UNISONIC TECHNOLOGIES CO., LTD MJE13007 NPN SILICON TRANSISTOR

Transcription

1 UNISONIC TECHNOLOGIES CO., LTD MJE3007 NPN BIPOLAR POWER TRANSISTOR FOR SWITCHING POWER SUPPLY APPLICATIONS DESCRIPTION The UTC MJE3007 is designed for high-voltage, high-speed power switching inductive circuits where fall time is critical. It is particularly suited for and 220 V switch mode applications. FEATURES * V CEO(SUS) 40V * 700V Blocking Capability Lead-free: MJE3007L Halogen-free:MJE3007G ORDERING INFORMATION Order Number Pin Assignment Package Normal Lead Free Halogen Free 2 3 Packing MJE3007-TA3-T MJE3007L-TA3-T MJE3007G-TA3-T TO-220 B C E Tube MJE3007-TF3-R MJE3007L-TF3-R MJE3007G-TF3-R TO-220F B C E Tube of 6 Copyright 2009 Unisonic Technologies Co., Ltd

2 ABSOLUTE MAXIMUM RATING PARAMETER SYMBOL RATINGS UNIT Collector-Emitter Sustaining Voltage V CEO 40 V Collector-Emitter Breakdown Voltage V CBO 700 V Emitter-Base Voltage V EBO 9.0 V Collector Current Continuous I C 8.0 A Peak () I CM 6 A Base Current Continuous I B 4.0 A Peak () I BM 8.0 A Continuous I E 2 A Emitter Current Peak () I EM 24 A Total Device Dissipation T C = 2 C P D 80 W Operating and Storage Junction Temperature T J, T STG -~+0 C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. THERMAL DATA PARAMETER SYMBOL RATINGS UNIT Junction to Case θ JC.6 C/W Junction to Ambient θ JA 62. C/W Note : Pulse Test: Pulse Width =.0 ms, Duty Cycle %. Measurement made with thermocouple contacting the bottom insulated mounting surface of the package (in a location beneath the die), the device mounted on a heatsink with thermal grease applied at a mounting torque of 6 to 8 lbs. ELECTRICAL CHARACTERISTICS (T C =2 C, unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Collector-Emitter Sustaining Voltage V CEO(SUS) I C =ma, I B =0 40 V Collector Cutoff Current I CBO V CES =700V 0. ma V CES =700V, T C =2 C.0 ma Emitter Cutoff Current I EBO V EB =9.0V, I C =0 0 μa DC Current Gain h FE I C =2.0A, V CE =.0V h FE2 I C =.0A, V CE =.0V.0 30 I C =2.0A, I B =0.4A.0 V Collector-Emitter Saturation Voltage V CE(SAT) I C =.0A, I B =.0A 2.0 V I C =8.0A, I B =2.0A 3.0 V I C =.0A, I B =.0A, T C =0 C 3.0 V I C =2.0A, I B =0.4A.2 V Base-Emitter Saturation Voltage V BE(SAT) I C =.0A, I B =.0A.6 V I C =.0A, I B =.0A, T C =0 C. V Current-Gain-Bandwidth Product f T I C =00mA, V CE =V, f=.0 MHz MHz Output Capacitance C ob V CB =V, I E =0, f=0.mhz 80 pf Resistive Load (Table ) Delay Time t D μs V CC =2V, I C =.0A, Rise Time t R 0.. μs I B =I B2 =.0A, t p =2μs, Storage Time t S μs Duty Cycle.0% Fall Time t F μs * Pulse Test: Pulse Width 300μs, Duty Cycle 2.0% UNISONIC TECHNOLOGIES CO., LTD 2 of 6

3 TYPICAL THERMAL RESPONSE 0.7 D=0. 0. D= D=0. 0. D= D= D=0.0 SINGLE PULSE Figure. Typical Thermal Response 0. 2 P(pk) t t2 DUTY CYCLE, D=t/t2 Time, t (msec) R θjc (t)=r(t)r θjc R θjc =.6 C/W MAX D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT t TJ (pk) -T C =P (pk) R θjc (t) k There are two limitations on the power handling ability of a transistor: average junction temperature and second breakdown. Safe operating area curves indicate I C -V CE limits of the transistor that must be observed for reliable operation; i.e., the transistor must not be subjected to greater dissipation than the curves indicate. The data of Figure 7 is based on T C = 2 C; T J(pk) is variable depending on power level. Second breakdown pulse limits are valid for duty cycles to % but must be debated when T C 2 C. Second breakdown limitations do not debate the same as thermal limitations. Allowable current at the voltages shown on Figure 7 may be found at any case temperature by using the appropriate curve on Figure 9. At high case temperatures, thermal limitations will reduce the power that can be handled to values less than the limitations imposed by second breakdown. Use of reverse biased safe operating area data (Figure 8) is discussed in the applications information section. UNISONIC TECHNOLOGIES CO., LTD 3 of 6

4 Table. Test Conditions for Dynamic Performance REVERSE BIAS SAFE OPERATING AREA AND INDUCTIVE SWITCHING RESISTIVE SWITCHING TEST CIRCUITS CIRCUIT VALUES BV CEO (SUS) L=mH R B2 =8 V CC =20V I C(pk) =0mA Inductive Switching L=20mH R B2 =0 V CC =V R B selected for desired I B RBSOA L=00mH R B2 =0 V CC =Volts R B selected for desired I B V CC =2V R C =2Ω D=N820 OR EQUIV UNISONIC TECHNOLOGIES CO., LTD 4 of 6

5 TYPICAL CHARACTERISTICS Figure 2. Base-Emitter Saturation Voltage Figure 3. Collector-Emitter Saturation Voltage Base-Emitte Saturation Voltage, VBE(SAT) (V) I C =-40 C 2 C 0 C Collector Current, I C (A) I C /I B = Collector-Emitte Saturation Voltage, VCE(SAT) (V) I C =-40 C 2 C C Collector Current, I C (A) I C /I B = Collector-Emitter Voltage, VCE (V) Capacitance, C (pf) DC Current Gain, hfe Figure 6. Capacitance C ib C ob 0 Reverse Voltage,V R (V) T J =2 C 00 Collector Current, IC (A) Figure 7. Maximum Forward Bias Safe Operating Area 0 0 Extended SOA@μs,μs 20 μs μs 2 T C =2 C ms DC ms 0. Bonding wire limit 0. Thermal limit 0.0 Second breakdown limit curves apply below 0.02 rated vceo Collector-Emitter Voltage, V CE (V) UNISONIC TECHNOLOGIES CO., LTD of 6

6 TYPICAL CHARACTERISTICS Figure 8. Maximum Reverse Bias Switching Safe Operating Area Figure 9. Forward Bias Power Derating Collector Current, IC (A) T C 0 C G AIN 4 L C =00μH V V BE(OFF) -V -2V Power Derating Factor THERMAL DERATING SECOND BREAKDOWN DERATING Collector-Emitter Clamp Voltage, V CEV (V) Case Temperature, T C ( C) Time, t (ns) Time, t (ns) UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD 6 of 6