BJT Circuits & Limitations LTspice
|
|
- Deirdre Charles
- 7 years ago
- Views:
Transcription
1 BJT Circuits & Limitations LTspice Acnowledgements: Neamen, Donald: Microelectronics Circuit Analysis and Design, 3 rd Edition LTspice material by Devon Rosner 13 (6.101 TA), Engineer, Linear Technology Spring 2015 Lecture 3 1
2 BJT Configurations Voltage Gain Current Gain Power Gain Common Emitter X X X Common Collector X X Common Base X X Common emitter: hgh input impedance, for general amplification of voltage, current and power from low power, high impedance sources. Common collector: aka "emitter follower" for high input impedance and current gain without voltage gain, as in an amplifier output stage. Common base: low input impedance for low impedance sources, for high frequency response. Grounding the base short circuits the Miller capacitance from collector to base and makes possible much higher frequency response Spring 2015 Lecture 3 2
3 General Configuration Common Emitter Common Collector Common Base Spring 2015 Lecture 3 3
4 Transistor Configurations TRANSISTOR AMPLIFIER CONFIGURATIONS +15V +15V +15V R L R L R 2 R 2 R V in - + R 1 R E + V OUT - + V in - + R 1 R E + + V OUT - + V in - + R 1 + R E + V OUT - [a] Common Emitter Amplifier [b] Common Collector [Emitter Follower] Amplifier [c] Common Base Amplifier Spring 2015 Lecture 3 4
5 Base Current Resistor Divider 68K i b I C F 3.7 ma ma ma ma 300 I C =0.6 ma 33K i b Make small compared to the current through R 2 See handout: Transistor bias stability Spring 2015 Lecture 3 5
6 Commom Emitter Hybrid π TRANSISTOR AMPLIFIER CONFIGURATIONS WITH HYBRID- EQUIVALENT CIRCUITS COMMON EMITTER AMPLIFER C R s + v in _ + R B I B R L +15V I C 2N v out _ g g 0 m v g m v m I V r CQ TH V TH 26mv b i b r R s R B R L + v in e _ c + v out _ A if R s =R B // R S v v v R' S out in r ; oibr i R' r b s then A L v or R' r s or o g m L L g m R L Spring 2015 Lecture 3 6
7 Common Emitter with Emitter Degeneration Spring 2015 Lecture 3 7 E L v E o s E o s L o E o s b L b o in out v R R then A R r R if R r R R R r R i R i v v A / ; 1 ' ; 1 ' 1 ' Input resistance (β+1)r E Voltage gain reduced by (1+g m R E ) Voltage gain less dependent on β (linearity) R s =R B // R S
8 AC Coupled vs DC Coupled Amplifiers AC Coupling Advantage: easy cascading with DC blocking capacitor, bias stability and stage independent Disadvantage: lot s of R s and C s, no DC gain, need large C for low freqency DC coupling Same gain at DC Fewer R s C s Spring 2015 Lecture 3 8
9 Gain vs Frequency Spring 2015 Lecture 3 9
10 Expanded Hybrid π r x Spring 2015 Lecture 3 10
11 Miller Effect* Common Emitter C M C [ 1 gm( RC RL )] * Agarwal & Lang Foundations of Analog & Digital Electronics Circuits p Spring 2015 Lecture 3 11
12 Low Pass Filter LPF log scale A V (db) R C V 1 V 2 0-3dB slope = -6 db / octave slope = -20 db / decade A A v v V V 2 1 j X C R j X 1 src 1 C 1 j C 1 R j C 1 j RC 1 0 o Degrees PHASE LAG f HI or f -3dB log f High frequency cutoff f hi 1 2RC -45 o -90 o log f f HI or f -3dB Spring 2015 Lecture 2 12
13 g m q I C kt 0 h fe (datasheet) C C ob Hybrid π Parameters (datasheet) g m 2(C C ) f T (transit frequency datasheet) C g m 2 f T r C r x (low frequency):datasheet or estimate (high frequency):estimate Spring 2015 Lecture 3 13
14 β Use max for worst case c u Spring 2015 Lecture 3 14
15 2N3904 CE configuration, V CC +15v Spring 2015 Lecture 3 15
16 h fe and High Frequency Limits Small signal current gain versus frequency, h fe, of a BJT biased in a common emitter configuration: i b v r be v be jc h fe gmv i b be gmr 1 jr C 1 jr C For h fe =1 = f T, (transit frequency ) h T gm 2C where C ( c c ) For 2N3904*, I C =1ma, V CE =10V, c π =25pF, c μ =2pF f T 0.04mho 2 27 pf for a gain of 240MHz g m R L 100 f h 2 r 1 g m R L c K(100)2 pf 320kHz Miller effect reduces high frequency limit! *Lundberg, Kent: Become One with the Transistor p Spring 2015 Lecture 3 16
17 Common Base Configuration Spring 2015 Lecture 3 17
18 Common Collector (Emitter Follower) Spring 2015 Lecture ; 1 ' ; 1 ' 1 1 ' 1 v E o s E o s E o E o s b E b o in out v A then R r R if R r R R R r R i R i v v A Buffer with unity gain High input resistance driving low output resistance (current gain). R s =R B // R S mv V V I g r g TH TH CQ m m 26 0 v g v m
19 Common Collector Emitter Follower Biasing R 2 A +15V 7.5 ma 2N3904 Β = 100, i B = 7.5ma/100 = 75µa Using Thevenin equivalent, R B = R 1 R 2, V B = 15 R R1 R 1 2 R 1 B 1.0 k 7.5 ma +15V V B = I B R B + 0.6V + 7.5V V B = [75 µa x 10k] + 0.6V + 7.5V V B = 750 mv + 0.6V + 7.5V V B = 8.9V I B R B V B 7.5 ma 2N V [15 R 1 ] [R 1 + R 2 ] = 8.9V 15 R 1 = 8.9 x [R 1 + R 2 ] [15 8.9] R 1 = 8.9 R 2 R 1 = 1.44 R 2 [R 1 x R 2 ] [R 1 + R 2 ] = 10 kω [1.44R 2 x R 2 ] [1.44 R 2 + R 2 ] = 10kΩ R 2 = 16.9 kω (use 16 kω) R 1 = 1.44 R 2 = 24.4 kω (use 24 kω) Spring 2015 Lecture 3 19
20 Common Collector Emitter Follower Biasing +15V With R1 = 24kΩ, R2 = 16 kω, the current through the voltage divider is 15 [40 kω] = 375 µa. R 2 I Divider 7.5 ma The 75 µa base current is 20% of 375 µa. 8.1 V R 1 A B 1.0 k 2N ma With R1 = 2 kω, will need a divider current that is ~ 4.1 ma. (75 µa is only ~2% of 4.1 ma, which is negligible) The voltage drop across R2 will be [15 V 8.1 V] = 6.9 V; R2 = 1.7 kω But input impedance will be low = ~890Ω Use bootstrapping configuration = 24.4 kω (use 24 kω) Spring 2015 Lecture 3 20
21 Low Frequency Hybrid Equation Chart High gain applications Moderate input resistance High output resistance Unity gain, low output resistance High input resist. High gain, better high frequency response Low input resistance Spring 2015 Lecture 3 21
22 Introduction to LTspice Acknowledgment: LTspice material by Devon Rosner (6.101 TA), Engineer, Linear Technology Spring 2015 Lecture 4 22
23 SPICE Simulation Program with Integrated Circuit Emphasis Developed in 1973 by Laurence Nagel at UC Berkeley s Electronics Research Laboratory Dependent on user defined device models Spring 2015 Lecture 4 23
24 Netlists Spring 2015 Lecture 4 24
25 LTspice Developed in 1998 by Mike Engelhardt at Linear Technology Corporation GUI, simulator and schematic > netlist for SPICE Free with lot s of models! Spring 2015 Lecture 4 25
26 LTspice Available Windows and MAC OS X Windows version easier to use. For MAC users install Windows version under VMware or use WINE (short for Wine Is Not an Emulator) Spring 2015 Lecture 4 26
27 Getting Started Spring 2015 Lecture 4 27
28 Component to Menu Item Spring 2015 Lecture 4 28
29 Net Labels Labeling nets avoid drawing wires. Use nets for power supply voltages, ground, circuit wide signals Spring 2015 Lecture 4 29
30 Adding Other Components Spring 2015 Lecture 4 30
31 Op Amps Spring 2015 Lecture 4 31
32 Editing Components Spring 2015 Lecture 4 32
33 Component Values 1 MEG = 1 megohm resistor 1 = 1 farad capacitor (not 1F) Spring 2015 Lecture 4 33
34 Basic Voltage Source Basic voltage source: used for DC supply voltage or bias voltage Spring 2015 Lecture 4 34
35 Advanced Voltage Sources Voltage source can produce arbitrary test signals using a PWL (Piece Wise Linearly) test file Spring 2015 Lecture 4 35
36 Device Models Many device models provided by Ltspice (BJT, MOSFETS, diodes Spring 2015 Lecture 4 36
37 Simulation: Transient Voltage/Current vs Time Spring 2015 Lecture 4 37
38 Simulation Stop Time Spring 2015 Lecture 4 38
39 Parameters in Simulation Spring 2015 Lecture 4 39
40 What Should My Circuit Do? Before running simulation you should have an ideal of how the circuit behaves. Simulation is a verification tool circuit solver Spring 2015 Lecture 4 40
41 Analyze this circuit Spring 2015 Lecture 4 41
42 Low Pass Filter Use low pass filter (LPF). Sallen Key filter is a second order filter. (A second order filter attenuates by a factor of one fourth for every doubling of frequency.) For low frequencies, capacitors are open circuit op amp feeds signal through. For high frequencies, capactiors act as shorts. f c 1 2RC R = 10K C = 1n (1nf) f c = 16 khz IAP 2015 Lecture 3 42
43 Transient Simulation Spring 2015 Lecture 4 43
44 Low Pass Filter Simulation Spring 2015 Lecture 4 44
45 AC Simulation Spring 2015 Lecture 4 45
46 AC Simulation Spring 2015 Lecture 4 46
47 Math In LTspice Spring 2015 Lecture 4 47
48 Transient Analysis Spring 2015 Lecture 4 48
49 More Fun Spring 2015 Lecture 4 49
50 AC Simulation Spring 2015 Lecture 4 50
51 Finishing Touches Spring 2015 Lecture 4 51
52 Finishing Touches Spring 2015 Lecture 4 52
BJT Characteristics and Amplifiers
BJT Characteristics and Amplifiers Matthew Beckler beck0778@umn.edu EE2002 Lab Section 003 April 2, 2006 Abstract As a basic component in amplifier design, the properties of the Bipolar Junction Transistor
More informationDEGREE: Bachelor in Biomedical Engineering YEAR: 2 TERM: 2 WEEKLY PLANNING
SESSION WEEK COURSE: Electronic Technology in Biomedicine DEGREE: Bachelor in Biomedical Engineering YEAR: 2 TERM: 2 WEEKLY PLANNING DESCRIPTION GROUPS (mark X) SPECIAL ROOM FOR SESSION (Computer class
More informationCommon Base BJT Amplifier Common Collector BJT Amplifier
Common Base BJT Amplifier Common Collector BJT Amplifier Common Collector (Emitter Follower) Configuration Common Base Configuration Small Signal Analysis Design Example Amplifier Input and Output Impedances
More informationTransistor Amplifiers
Physics 3330 Experiment #7 Fall 1999 Transistor Amplifiers Purpose The aim of this experiment is to develop a bipolar transistor amplifier with a voltage gain of minus 25. The amplifier must accept input
More informationCommon Emitter BJT Amplifier Design Current Mirror Design
Common Emitter BJT Amplifier Design Current Mirror Design 1 Some Random Observations Conditions for stabilized voltage source biasing Emitter resistance, R E, is needed. Base voltage source will have finite
More informationLABORATORY 2 THE DIFFERENTIAL AMPLIFIER
LABORATORY 2 THE DIFFERENTIAL AMPLIFIER OBJECTIVES 1. To understand how to amplify weak (small) signals in the presence of noise. 1. To understand how a differential amplifier rejects noise and common
More informationCommon-Emitter Amplifier
Common-Emitter Amplifier A. Before We Start As the title of this lab says, this lab is about designing a Common-Emitter Amplifier, and this in this stage of the lab course is premature, in my opinion,
More informationTDA2040. 20W Hi-Fi AUDIO POWER AMPLIFIER
20W Hi-Fi AUDIO POWER AMPLIFIER DESCRIPTION The TDA2040 is a monolithic integrated circuit in Pentawatt package, intended for use as an audio class AB amplifier. Typically it provides 22W output power
More informationTDA2040. 20W Hi-Fi AUDIO POWER AMPLIFIER
20W Hi-Fi AUDIO POWER AMPLIFIER DESCRIPTION The TDA2040 is a monolithic integrated circuit in Pentawatt package, intended for use as an audio class AB amplifier. Typically it provides 22W output power
More informationTransistor Characteristics and Single Transistor Amplifier Sept. 8, 1997
Physics 623 Transistor Characteristics and Single Transistor Amplifier Sept. 8, 1997 1 Purpose To measure and understand the common emitter transistor characteristic curves. To use the base current gain
More informationUniversity of California, Berkeley Department of Electrical Engineering and Computer Sciences EE 105: Microelectronic Devices and Circuits
University of California, Berkeley Department of Electrical Engineering and Computer Sciences EE 105: Microelectronic Devices and Circuits LTSpice LTSpice is a free circuit simulator based on Berkeley
More informationLaboratory 4: Feedback and Compensation
Laboratory 4: Feedback and Compensation To be performed during Week 9 (Oct. 20-24) and Week 10 (Oct. 27-31) Due Week 11 (Nov. 3-7) 1 Pre-Lab This Pre-Lab should be completed before attending your regular
More informationChapter 12: The Operational Amplifier
Chapter 12: The Operational Amplifier 12.1: Introduction to Operational Amplifier (Op-Amp) Operational amplifiers (op-amps) are very high gain dc coupled amplifiers with differential inputs; they are used
More informationPhysics 623 Transistor Characteristics and Single Transistor Amplifier Sept. 13, 2006
Physics 623 Transistor Characteristics and Single Transistor Amplifier Sept. 13, 2006 1 Purpose To measure and understand the common emitter transistor characteristic curves. To use the base current gain
More informationDesign of a TL431-Based Controller for a Flyback Converter
Design of a TL431-Based Controller for a Flyback Converter Dr. John Schönberger Plexim GmbH Technoparkstrasse 1 8005 Zürich 1 Introduction The TL431 is a reference voltage source that is commonly used
More informationLecture 23: Common Emitter Amplifier Frequency Response. Miller s Theorem.
Whites, EE 320 ecture 23 Page 1 of 17 ecture 23: Common Emitter mplifier Frequency Response. Miller s Theorem. We ll use the high frequency model for the BJT we developed the previous lecture and compute
More informationTransistor Models. ampel
Transistor Models Review of Transistor Fundamentals Simple Current Amplifier Model Transistor Switch Example Common Emitter Amplifier Example Transistor as a Transductance Device - Ebers-Moll Model Other
More informationBipolar Transistor Amplifiers
Physics 3330 Experiment #7 Fall 2005 Bipolar Transistor Amplifiers Purpose The aim of this experiment is to construct a bipolar transistor amplifier with a voltage gain of minus 25. The amplifier must
More informationCOMMON-SOURCE JFET AMPLIFIER
EXPERIMENT 04 Objectives: Theory: 1. To evaluate the common-source amplifier using the small signal equivalent model. 2. To learn what effects the voltage gain. A self-biased n-channel JFET with an AC
More informationMAS.836 HOW TO BIAS AN OP-AMP
MAS.836 HOW TO BIAS AN OP-AMP Op-Amp Circuits: Bias, in an electronic circuit, describes the steady state operating characteristics with no signal being applied. In an op-amp circuit, the operating characteristic
More informationChapter 8 Differential and Multistage Amplifiers. EE 3120 Microelectronics II
1 Chapter 8 Differential and Multistage Amplifiers Operational Amplifier Circuit Components 2 1. Ch 7: Current Mirrors and Biasing 2. Ch 9: Frequency Response 3. Ch 8: Active-Loaded Differential Pair 4.
More informationBJT Amplifier Circuits
JT Amplifier ircuits As we have developed different models for D signals (simple large-signal model) and A signals (small-signal model), analysis of JT circuits follows these steps: D biasing analysis:
More informationDigital to Analog Converter. Raghu Tumati
Digital to Analog Converter Raghu Tumati May 11, 2006 Contents 1) Introduction............................... 3 2) DAC types................................... 4 3) DAC Presented.............................
More information6.101 Final Project Report Class G Audio Amplifier
6.101 Final Project Report Class G Audio Amplifier Mark Spatz 4/3/2014 1 1 Introduction For my final project, I designed and built a 150 Watt audio amplifier to replace the underpowered and unreliable
More informationVoltage Divider Bias
Voltage Divider Bias ENGI 242 ELEC 222 BJT Biasing 3 For the Voltage Divider Bias Configurations Draw Equivalent Input circuit Draw Equivalent Output circuit Write necessary KVL and KCL Equations Determine
More informationLocal Oscillator for FM broadcast band 88-108 MHz
Local Oscillator for FM broadcast band 88-108 MHz Wang Luhao Yan Shubo Supervisor: Göran Jönsson Department of Electrical and Information Technology Lund University 2012.05.15 Abstract In this project
More informationOp-Amp Simulation EE/CS 5720/6720. Read Chapter 5 in Johns & Martin before you begin this assignment.
Op-Amp Simulation EE/CS 5720/6720 Read Chapter 5 in Johns & Martin before you begin this assignment. This assignment will take you through the simulation and basic characterization of a simple operational
More informationBJT Circuit Configurations
BJT Circuit Configurations V be ~ ~ ~ v s R L v s R L V Vcc R s cc R s v s R s R L V cc Common base Common emitter Common collector Common emitter current gain BJT Current-Voltage Characteristics V CE,
More informationAN1991. Audio decibel level detector with meter driver
Rev. 2.1 20 March 2015 Application note Document information Info Keywords Abstract Content SA604A, LM358, RSSI, cellular radio The SA604A can provide a logarithmic response proportional to the input signal
More informationReading: HH Sections 4.11 4.13, 4.19 4.20 (pgs. 189-212, 222 224)
6 OP AMPS II 6 Op Amps II In the previous lab, you explored several applications of op amps. In this exercise, you will look at some of their limitations. You will also examine the op amp integrator and
More informationLow Noise, Matched Dual PNP Transistor MAT03
a FEATURES Dual Matched PNP Transistor Low Offset Voltage: 100 V Max Low Noise: 1 nv/ Hz @ 1 khz Max High Gain: 100 Min High Gain Bandwidth: 190 MHz Typ Tight Gain Matching: 3% Max Excellent Logarithmic
More informationObjective. To design and simulate a cascode amplifier circuit using bipolar transistors.
ascode Amplifier Design. Objective. o design and simulate a cascode amplifier circuit using bipolar transistors. Assignment description he cascode amplifier utilises the advantage of the common-emitter
More informationLecture 24. Inductance and Switching Power Supplies (how your solar charger voltage converter works)
Lecture 24 Inductance and Switching Power Supplies (how your solar charger voltage converter works) Copyright 2014 by Mark Horowitz 1 Roadmap: How Does This Work? 2 Processor Board 3 More Detailed Roadmap
More information*For stability of the feedback loop, the differential gain must vary as
ECE137a Lab project 3 You will first be designing and building an op-amp. The op-amp will then be configured as a narrow-band amplifier for amplification of voice signals in a public address system. Part
More information11: AUDIO AMPLIFIER I. INTRODUCTION
11: AUDIO AMPLIFIER I. INTRODUCTION The properties of an amplifying circuit using an op-amp depend primarily on the characteristics of the feedback network rather than on those of the op-amp itself. A
More informationUnit/Standard Number. High School Graduation Years 2010, 2011 and 2012
1 Secondary Task List 100 SAFETY 101 Demonstrate an understanding of State and School safety regulations. 102 Practice safety techniques for electronics work. 103 Demonstrate an understanding of proper
More informationOPERATIONAL AMPLIFIERS
INTRODUCTION OPERATIONAL AMPLIFIERS The student will be introduced to the application and analysis of operational amplifiers in this laboratory experiment. The student will apply circuit analysis techniques
More informationTWO PORT NETWORKS h-parameter BJT MODEL
TWO PORT NETWORKS h-parameter BJT MODEL The circuit of the basic two port network is shown on the right. Depending on the application, it may be used in a number of different ways to develop different
More informationENEE 307 Electronic Circuit Design Laboratory Spring 2012. A. Iliadis Electrical Engineering Department University of Maryland College Park MD 20742
1.1. Differential Amplifiers ENEE 307 Electronic Circuit Design Laboratory Spring 2012 A. Iliadis Electrical Engineering Department University of Maryland College Park MD 20742 Differential Amplifiers
More informationLM1036 Dual DC Operated Tone/Volume/Balance Circuit
LM1036 Dual DC Operated Tone/Volume/Balance Circuit General Description The LM1036 is a DC controlled tone (bass/treble), volume and balance circuit for stereo applications in car radio, TV and audio systems.
More informationWhat Does Rail-to-Rail Operation Really Mean?
What Does Rail-to-Rail Operation Really Mean? 2004 Microchip Technology Incorporated. All Rights Reserved. What does Rail-to-Rail Operation really mean? 1 Agenda What does Rail-to-Rail output operation
More informationSingle Supply Op Amp Circuits Dr. Lynn Fuller
ROCHESTER INSTITUTE OF TECHNOLOGY MICROELECTRONIC ENGINEERING Single Supply Op Amp Circuits Dr. Lynn Fuller Webpage: http://people.rit.edu/lffeee 82 Lomb Memorial Drive Rochester, NY 146235604 Tel (585)
More informationLM 358 Op Amp. If you have small signals and need a more useful reading we could amplify it using the op amp, this is commonly used in sensors.
LM 358 Op Amp S k i l l L e v e l : I n t e r m e d i a t e OVERVIEW The LM 358 is a duel single supply operational amplifier. As it is a single supply it eliminates the need for a duel power supply, thus
More informationBJT Amplifier Circuits
JT Amplifier ircuits As we have developed different models for D signals (simple large-signal model) and A signals (small-signal model), analysis of JT circuits follows these steps: D biasing analysis:
More informationEquivalent Circuit. Operating Characteristics at Ta = 25 C, V CC = ±34V, R L = 8Ω, VG = 40dB, Rg = 600Ω, R L : non-inductive load STK4181V
Ordering number: 2137B Thick Film Hybrid IC STK4181V AF Power Amplifier (Split Power Supply) (45W + 45W min, THD = 0.08%) Features Pin-compatible with the STK4102II series. The STK4101V series use the
More informationLab 7: Operational Amplifiers Part I
Lab 7: Operational Amplifiers Part I Objectives The objective of this lab is to study operational amplifier (op amp) and its applications. We will be simulating and building some basic op amp circuits,
More informationLAB VIII. BIPOLAR JUNCTION TRANSISTOR CHARACTERISTICS
LAB VIII. BIPOLAR JUNCTION TRANSISTOR CHARACTERISTICS 1. OBJECTIVE In this lab, you will study the DC characteristics of a Bipolar Junction Transistor (BJT). 2. OVERVIEW In this lab, you will inspect the
More informationAmplifier Teaching Aid
Amplifier Teaching Aid Table of Contents Amplifier Teaching Aid...1 Preface...1 Introduction...1 Lesson 1 Semiconductor Review...2 Lesson Plan...2 Worksheet No. 1...7 Experiment No. 1...7 Lesson 2 Bipolar
More informationBaseband delay line QUICK REFERENCE DATA
FEATURES Two comb filters, using the switched-capacitor technique, for one line delay time (64 µs) Adjustment-free application No crosstalk between SECAM colour carriers (diaphoty) Handles negative or
More informationThe 2N3393 Bipolar Junction Transistor
The 2N3393 Bipolar Junction Transistor Common-Emitter Amplifier Aaron Prust Abstract The bipolar junction transistor (BJT) is a non-linear electronic device which can be used for amplification and switching.
More informationProgrammable Single-/Dual-/Triple- Tone Gong SAE 800
Programmable Single-/Dual-/Triple- Tone Gong Preliminary Data SAE 800 Bipolar IC Features Supply voltage range 2.8 V to 18 V Few external components (no electrolytic capacitor) 1 tone, 2 tones, 3 tones
More informationObjectives The purpose of this lab is build and analyze Differential amplifiers based on NPN transistors (or NMOS transistors).
1 Lab 03: Differential Amplifiers (BJT) (20 points) NOTE: 1) Please use the basic current mirror from Lab01 for the second part of the lab (Fig. 3). 2) You can use the same chip as the basic current mirror;
More information100V - 100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BY THERMAL SHUTDOWN STBY-GND
TDA7294 100V - 100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BY VERY HIGH OPERATING VOLTAGE RANGE (±40V) DMOS POWER STAGE HIGH OUTPUT POWER (UP TO 100W MU- SIC POWER) MUTING/STAND-BY FUNCTIONS NO SWITCH ON/OFF
More informationP D 215 1.25 Operating Junction Temperature T J 200 C Storage Temperature Range T stg 65 to +150 C
SEMICONDUCTOR TECHNICAL DATA Order this document by /D The RF Line The is designed for output stages in band IV and V TV transmitter amplifiers. It incorporates high value emitter ballast resistors, gold
More informationSophomore Physics Laboratory (PH005/105)
CALIFORNIA INSTITUTE OF TECHNOLOGY PHYSICS MATHEMATICS AND ASTRONOMY DIVISION Sophomore Physics Laboratory (PH5/15) Analog Electronics Active Filters Copyright c Virgínio de Oliveira Sannibale, 23 (Revision
More informationQucs. A Tutorial. Getting Started with Qucs. Stefan Jahn Juan Carlos Borrás
Qucs A Tutorial Getting Started with Qucs Stefan Jahn Juan Carlos Borrás Copyright c 2007 Stefan Jahn Copyright c 2007 Juan Carlos Borrás Permission is granted to
More informationApplication Note SAW-Components
Application Note SAW-Components Principles of SAWR-stabilized oscillators and transmitters. App: Note #1 This application note describes the physical principle of SAW-stabilized oscillator. Oscillator
More informationLAB VII. BIPOLAR JUNCTION TRANSISTOR CHARACTERISTICS
LAB VII. BIPOLAR JUNCTION TRANSISTOR CHARACTERISTICS 1. OBJECTIVE In this lab, you will study the DC characteristics of a Bipolar Junction Transistor (BJT). 2. OVERVIEW You need to first identify the physical
More informationHigh Common-Mode Rejection. Differential Line Receiver SSM2141. Fax: 781/461-3113 FUNCTIONAL BLOCK DIAGRAM FEATURES. High Common-Mode Rejection
a FEATURES High Common-Mode Rejection DC: 00 db typ 60 Hz: 00 db typ 20 khz: 70 db typ 40 khz: 62 db typ Low Distortion: 0.00% typ Fast Slew Rate: 9.5 V/ s typ Wide Bandwidth: 3 MHz typ Low Cost Complements
More information3.4 - BJT DIFFERENTIAL AMPLIFIERS
BJT Differential Amplifiers (6/4/00) Page 1 3.4 BJT DIFFERENTIAL AMPLIFIERS INTRODUCTION Objective The objective of this presentation is: 1.) Define and characterize the differential amplifier.) Show the
More informationBasic Electronics Prof. Dr. Chitralekha Mahanta Department of Electronics and Communication Engineering Indian Institute of Technology, Guwahati
Basic Electronics Prof. Dr. Chitralekha Mahanta Department of Electronics and Communication Engineering Indian Institute of Technology, Guwahati Module: 2 Bipolar Junction Transistors Lecture-2 Transistor
More informationCIRCUITS LABORATORY. In this experiment, the output I-V characteristic curves, the small-signal low
CIRCUITS LABORATORY EXPERIMENT 6 TRANSISTOR CHARACTERISTICS 6.1 ABSTRACT In this experiment, the output I-V characteristic curves, the small-signal low frequency equivalent circuit parameters, and the
More informationCurrent vs. Voltage Feedback Amplifiers
Current vs. ltage Feedback Amplifiers One question continuously troubles the analog design engineer: Which amplifier topology is better for my application, current feedback or voltage feedback? In most
More informationAN105. Introduction: The Nature of VCRs. Resistance Properties of FETs
Introduction: The Nature of s A voltage-controlled resistor () may be defined as a three-terminal variable resistor where the resistance value between two of the terminals is controlled by a voltage potential
More informationwww.jameco.com 1-800-831-4242
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LF411 Low Offset, Low Drift JFET Input Operational Amplifier General Description
More informationElectronics. Discrete assembly of an operational amplifier as a transistor circuit. LD Physics Leaflets P4.2.1.1
Electronics Operational Amplifier Internal design of an operational amplifier LD Physics Leaflets Discrete assembly of an operational amplifier as a transistor circuit P4.2.1.1 Objects of the experiment
More informationCollection of Solved Feedback Amplifier Problems
c Copyright 2009. W. Marshall Leach, Jr., Professor, Georgia Institute of Technology, School of Electrical and Computer Engineering. Collection of Solved Feedback Amplifier Problems This document contains
More informationY.LIN ELECTRONICS CO.,LTD.
Features Current transfer ratio (CTR 50~600% at I F =5mA, V CE =5V) High isolation voltage between input and output (Viso=5000 V rms ) Creepage distance >7.62 mm Operating temperature up to +110 C Compact
More informationPIN CONFIGURATION FEATURES ORDERING INFORMATION ABSOLUTE MAXIMUM RATINGS. D, F, N Packages
DESCRIPTION The µa71 is a high performance operational amplifier with high open-loop gain, internal compensation, high common mode range and exceptional temperature stability. The µa71 is short-circuit-protected
More informationSeries AMLDL-Z Up to 1000mA LED Driver
FEATURES: Click on Series name for product info on aimtec.com Series Up to ma LED Driver Models Single output Model Input Voltage (V) Step Down DC/DC LED driver Operating Temperature range 4ºC to 85ºC
More informationLab #9: AC Steady State Analysis
Theory & Introduction Lab #9: AC Steady State Analysis Goals for Lab #9 The main goal for lab 9 is to make the students familar with AC steady state analysis, db scale and the NI ELVIS frequency analyzer.
More information30. Bode Plots. Introduction
0. Bode Plots Introduction Each of the circuits in this problem set is represented by a magnitude Bode plot. The network function provides a connection between the Bode plot and the circuit. To solve these
More informationSchool of Engineering Department of Electrical and Computer Engineering
1 School of Engineering Department of Electrical and Computer Engineering 332:223 Principles of Electrical Engineering I Laboratory Experiment #4 Title: Operational Amplifiers 1 Introduction Objectives
More informationNotes about Small Signal Model. for EE 40 Intro to Microelectronic Circuits
Notes about Small Signal Model for EE 40 Intro to Microelectronic Circuits 1. Model the MOSFET Transistor For a MOSFET transistor, there are NMOS and PMOS. The examples shown here would be for NMOS. Figure
More informationLecture 18: Common Emitter Amplifier. Maximum Efficiency of Class A Amplifiers. Transformer Coupled Loads.
Whites, EE 3 Lecture 18 Page 1 of 10 Lecture 18: Common Emitter Amplifier. Maximum Efficiency of Class A Amplifiers. Transformer Coupled Loads. We discussed using transistors as switches in the last lecture.
More informationLM118/LM218/LM318 Operational Amplifiers
LM118/LM218/LM318 Operational Amplifiers General Description The LM118 series are precision high speed operational amplifiers designed for applications requiring wide bandwidth and high slew rate. They
More informationLM386 Low Voltage Audio Power Amplifier
Low Voltage Audio Power Amplifier General Description The LM386 is a power amplifier designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count
More informationDifferential Amplifier Offset. Causes of dc voltage and current offset Modeling dc offset R C
ESE39 ntroduction to Microelectronics Differential Amplifier Offset Causes of dc voltage and current offset Modeling dc offset mismatch S mismatch β mismatch transistor mismatch dc offsets in differential
More informationUnderstanding Power Impedance Supply for Optimum Decoupling
Introduction Noise in power supplies is not only caused by the power supply itself, but also the load s interaction with the power supply (i.e. dynamic loads, switching, etc.). To lower load induced noise,
More informationDesign of op amp sine wave oscillators
Design of op amp sine wave oscillators By on Mancini Senior Application Specialist, Operational Amplifiers riteria for oscillation The canonical form of a feedback system is shown in Figure, and Equation
More informationLAB 12: ACTIVE FILTERS
A. INTRODUCTION LAB 12: ACTIVE FILTERS After last week s encounter with op- amps we will use them to build active filters. B. ABOUT FILTERS An electric filter is a frequency-selecting circuit designed
More informationSupply voltage Supervisor TL77xx Series. Author: Eilhard Haseloff
Supply voltage Supervisor TL77xx Series Author: Eilhard Haseloff Literature Number: SLVAE04 March 1997 i IMPORTANT NOTICE Texas Instruments (TI) reserves the right to make changes to its products or to
More informationLM134-LM234 LM334 THREE TERMINAL ADJUSTABLE CURRENT SOURCES. OPERATES from 1V to 40V
LM134-LM234 LM334 THREE TERMINAL USTABLE CURRENT SOURCES OPERATES from 1 to 40. 0.02% CURRENT REGULATION PROGRAMMABLE from 1µA to 10mA ±3% INITIAL ACCURACY DESCRIPTION The LM134/LM234/LM334 are 3-terminal
More informationLab Report No.1 // Diodes: A Regulated DC Power Supply Omar X. Avelar Omar de la Mora Diego I. Romero
Instituto Tecnológico y de Estudios Superiores de Occidente (ITESO) Periférico Sur Manuel Gómez Morín 8585, Tlaquepaque, Jalisco, México, C.P. 45090 Analog Electronic Devices (ESI038 / SE047) Dr. Esteban
More informationLH0091 True RMS to DC Converter
LH0091 True RMS to DC Converter General Description The LH0091 rms to dc converter generates a dc output equal to the rms value of any input per the transfer function E OUT(DC) e 0 1 T T 0 E IN 2 (t) dt
More informationChapter 10. RC Circuits ISU EE. C.Y. Lee
Chapter 10 RC Circuits Objectives Describe the relationship between current and voltage in an RC circuit Determine impedance and phase angle in a series RC circuit Analyze a series RC circuit Determine
More informationOBJECTIVE QUESTIONS IN ANALOG ELECTRONICS
1. The early effect in a bipolar junction transistor is caused by (a) fast turn-on (c) large collector-base reverse bias (b)fast turn-off (d) large emitter-base forward bias 2. MOSFET can be used as a
More informationCMOS, the Ideal Logic Family
CMOS, the Ideal Logic Family INTRODUCTION Let s talk about the characteristics of an ideal logic family. It should dissipate no power, have zero propagation delay, controlled rise and fall times, and have
More informationBJT AC Analysis. by Kenneth A. Kuhn Oct. 20, 2001, rev Aug. 31, 2008
by Kenneth A. Kuhn Oct. 20, 2001, rev Aug. 31, 2008 Introduction This note will discuss AC analysis using the beta, re transistor model shown in Figure 1 for the three types of amplifiers: common-emitter,
More informationBipolar Junction Transistor Basics
by Kenneth A. Kuhn Sept. 29, 2001, rev 1 Introduction A bipolar junction transistor (BJT) is a three layer semiconductor device with either NPN or PNP construction. Both constructions have the identical
More informationApplication Report SLVA051
Application Report November 998 Mixed-Signal Products SLVA05 ltage Feedback Vs Current Feedback Op Amps Application Report James Karki Literature Number: SLVA05 November 998 Printed on Recycled Paper IMPORTANT
More informationUse and Application of Output Limiting Amplifiers (HFA1115, HFA1130, HFA1135)
Use and Application of Output Limiting Amplifiers (HFA111, HFA110, HFA11) Application Note November 1996 AN96 Introduction Amplifiers with internal voltage clamps, also known as limiting amplifiers, have
More informationLecture 3: DC Analysis of Diode Circuits.
Whites, EE 320 Lecture 3 Page 1 of 10 Lecture 3: DC Analysis of Diode Circuits. We ll now move on to the DC analysis of diode circuits. Applications will be covered in following lectures. Let s consider
More information2N6056. NPN Darlington Silicon Power Transistor DARLINGTON 8 AMPERE SILICON POWER TRANSISTOR 80 VOLTS, 100 WATTS
NPN Darlington Silicon Power Transistor The NPN Darlington silicon power transistor is designed for general purpose amplifier and low frequency switching applications. High DC Current Gain h FE = 3000
More informationContent Map For Career & Technology
Content Strand: Applied Academics CT-ET1-1 analysis of electronic A. Fractions and decimals B. Powers of 10 and engineering notation C. Formula based problem solutions D. Powers and roots E. Linear equations
More informationBJT AC Analysis 1 of 38. The r e Transistor model. Remind Q-poiint re = 26mv/IE
BJT AC Analysis 1 of 38 The r e Transistor model Remind Q-poiint re = 26mv/IE BJT AC Analysis 2 of 38 Three amplifier configurations, Common Emitter Common Collector (Emitter Follower) Common Base BJT
More informationSection 3. Sensor to ADC Design Example
Section 3 Sensor to ADC Design Example 3-1 This section describes the design of a sensor to ADC system. The sensor measures temperature, and the measurement is interfaced into an ADC selected by the systems
More informationLM741. Single Operational Amplifier. Features. Description. Internal Block Diagram. www.fairchildsemi.com
Single Operational Amplifier www.fairchildsemi.com Features Short circuit protection Excellent temperature stability Internal frequency compensation High Input voltage range Null of offset Description
More informationSmall Signal Analysis of a PMOS transistor Consider the following PMOS transistor to be in saturation. Then, 1 2
Small Signal Analysis of a PMOS transistor Consider the following PMOS transistor to be in saturation. Then, 1 I SD = µ pcox( VSG Vtp)^2(1 + VSDλ) 2 From this equation it is evident that I SD is a function
More informationCopyright 2011 Linear Technology. All rights reserved.
Copyright. All rights reserved. LTspice IV Getting Started Guide 2 Benefits of Using LTspice IV Stable SPICE circuit simulation with Unlimited number of nodes Schematic/symbol editor Waveform viewer Library
More information