SxX8xSx Series RoHS escription New device series offers high static dv/dt and lower turn off (t q ) sensitive SR with its small die planar construction design. It is specifically designed for I (round ault ircuit Interrupter) and as Ignition applications. ll SRs junctions are glass-passivated to ensure long term reliability and parametric stability. eatures Main eatures Symbol Value Unit I T(RMS) 0.8 V RM /V RRM 400 to 800 V I T 5 to 200 μ RoHS compliant and Halogen-ree Thru-hole and surface mount packages Surge current capability > 10mps Blocking voltage ( V RM / V RRM ) capability - up to 800V Schematic Symbol High dv/dt noise immunity Improved turn-off time (t q ) < 25 μsec Sensitive gate for direct microprocessor interface pplications The SxX8xSx EV series is specifically designed for I (round ault ircuit Interrupter) and gas ignition applications. K bsolute Maximum Ratings Symbol Parameter Value Unit TO-92 T = 55 0.8 I T(RMS) RMS on-state current (full sine wave) SOT-89 T = 60 0.8 SOT-223 T L = 60 0.8 TO-92 T = 55 0.51 I T(V) verage on-state current SOT-89 T = 60 0.51 SOT-223 T L = 60 0.51 I TSM TO-92 Non repetitive surge peak on-state current = 50Hz 8 SOT-89 (Single cycle, initial = 25 ) SOT-223 = 60Hz 10 t = 10 ms = 50 Hz 0.32 2 s I 2 t I 2 t Value for fusing p t p = 8.3 ms = 60 Hz 0.41 2 s TO-92 di/dt ritical rate of rise of on-state current I = 10m SOT-89 = 125 50 /µs SOT-223 I M Peak urrent t p = 10 μs = 125 1.0 P (V) verage gate power dissipation = 125 0.1 W T stg Storage junction temperature range -40 to 150 Operating junction temperature range -40 to 125
Electrical haracteristics ( = 25, unless otherwise specified) Symbol escription Test onditions Limit Value SxX8yS1 SxX8yS2 SxX8yS Unit I T V T Trigger urrent Trigger Voltage V = 6V R L = 100 Ω V = 6V R L = 100 Ω MIN. 0.5 1 15 μ MX. 5 50 200 μ MX. 0.8 V V RM Peak Reverse Voltage I R = 10μ MIN. 5 V I H Holding urrent R K = 1 KΩ Initial urrent = 20m MX. 5 m (dv/dt)s ritical Rate-of-Rise of Off-State Voltage = 125 V = V RM /V RRM Exp. Waveform R K =1 kω MIN. 75 V/μs V Non-Trigger Voltage V = V RM R K =1 kω = 25 MIN. 0.2 V t q Turn-Off Time = 25 @ 600 V R K =1 kω MX. 30 25 25 μs t gt Turn-On Time I =10m PW = 15μsec I T = 1.6(pk) TYP. 2.0 2.0 2.0 μs Note: x = voltage, y = package Static haracteristics ( = 25, unless otherwise specified) Symbol escription Test onditions Limit Value Unit V TM Peak On-State Voltage I TM = 1.6 (pk) MX. 1.70 V I RM Off-State urrent, Peak Repetitive = 25 @ V = V RM R K =1 kω = 125 @ V = V RM R K =1 kω MX. 3 μ MX. 500 μ Thermal Resistances Symbol escription Test onditions Value Unit TO-92 75 /W R th(j-c) Junction to case () I T = 0.8 (RMS) 1 SOT-223 30 /W SOT-89 50 /W TO-92 150 /W R th(j-a) Junction to ambient I T = 0.8 (RMS) 1 SOT-223 60 /W SOT-89 90 /W 1 60Hz resistive load condition, 100% conduction.
igure 1: Normalized Trigger urrent or ll Quadrants vs. Junction Temperature igure 2: Normalized Holding urrent vs. Junction Temperature 2.0 4.0 I T I T ( = 25 ) Ratio of 1.5 1.0 0.5 I H Ratio of I H ( = 25 ) 3.0 2.0 1.0 0.0-40 -15 +25 +65 +105 Junction Temperature ( ) - +125 0.0-55 -35-15 +5 +25 +45 +65 +85 +105 Junction Temperature ( ) - +125 igure 3: Normalized Trigger Voltage vs. Junction Temperature igure 4: On-State urrent vs. On-State Voltage (Typical) Trigger Voltage (V T ) - V 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2-40 -25-10 +5 +20 +35 +50 +65 +80 +95 +110 +125 Junction Temperature ( ) - Instantaneous On-state urrent (IT) mps 10 8 6 4 2 0 SxX8xS1 SxX8xS SxX8xS2 0.9 1.3 1.7 2.1 2.5 2.9 3.3 3.7 Instantaneous On-state Voltage (VT) Volts igure 5: Power issipation (Typical) vs. RMS On-State urrent igure 6: Maximum llowable ase Temperature vs. On-State urrent verage On-state Power issipation [P (V) ] - Watts 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 URRENT WVEORM: Sinusoidal LO: Resistive or Inductive ONUTION NLE: 180 o 0.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 RMS On-state urrent [I T(RMS) ] - mps Maximum llowable ase Temperature (T ) - o 130 120 110 100 90 80 70 60 TO-92 URRENT WVEORM: Sinusoidal LO: Resistive or Inductive ONUTION NLE: 180 o SE TEMPERTURE: Measured as shown on dimensional drawings SOT-223 & SOT-89 50 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 RMS On-state urrent [I T(RMS) ] - mps
Temperature Teccor brand Thyristors igure 7: Surge Peak On-State urrent vs. Number of ycles Peak Surge (Non-repetitive) On-State urrent (I TSM ) mps. 20 10 9 8 7 6 5 4 3 2 0.8 evices Supply requency: 60Hz Sinusoidal Load: Resistive RMS On-State urrent [I T(RMS) ]: Max Rated Value at Specific ase Temperature Notes: 1. control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 1 1 2 3 4 5 6 7 8910 20 30 40 60 80 100 200 300 400 600 1000 Surge urrent uration - ull ycle Soldering Parameters Reflow ondition Pb ree assembly T P t P - Temperature Min (T s(min) ) 150 Ramp-up Pre Heat - Temperature Max (T s(max) ) 200 - Time (min to max) (t s ) 60 180 secs verage ramp up rate (Liquidus Temp) (T L ) to peak 5 /second max T L T S(max) T S(min) Preheat t L Ramp-down T S(max) to T L - Ramp-up Rate 5 /second max t S - Temperature (T L ) (Liquidus) 217 Reflow - Time (min to max) (t s ) 60 150 seconds Peak Temperature (T P ) 260 +0/-5 25 time to peak temperature Time Time within 5 of actual peak Temperature (t p ) 20 40 seconds Ramp-down Rate 5 /second max Time 25 to peak Temperature (T P ) 8 minutes Max. o not exceed 280 dditional Information atasheet Resources Samples
Physical Specifications Reliability/Environmental Tests Terminal inish Body Material Lead Material esign onsiderations 100% Matte Tin-plated. UL recognized epoxy meeting flammability classification 94V-0. opper lloy areful selection of the correct device for the application s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. ood design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. orrect mounting, soldering, and forming of the leads also help protect against component damage. Test Blocking Temperature ycling Temperature/ Humidity High Temp Storage Low-Temp Storage Resistance to Solder Heat Solderability Lead Bend Specifications and onditions MIL-ST-750, M-1040, ond pplied Peak voltage @ 110 for 1008 hours MIL-ST-750, M-1051, 100 cycles; -40 to +150 ; 15-min dwell-time EI / JEE, JES22-101 1008 hours; 320V - : 85 ; 85% rel humidity MIL-ST-750, M-1031, 1008 hours; 150 1008 hours; -40 MIL-ST-750 Method 2031 NSI/J-ST-002, category 3, Test MIL-ST-750, M-2036 ond E imensions TO-92 T MESURIN POINT Inches Millimeters imension Min Max Min Max 0.175 0.205 4.450 5.200 B B 0.170 0.210 4.320 5.330 0.500 12.70 SETIN PLNE 0.135 3.430 E 0.125 0.165 3.180 4.190 TE 0.080 0.105 2.040 2.660 0.016 0.021 0.407 0.533 H 0.045 0.055 1.150 1.390 I 0.095 0.105 2.420 2.660 THOE H I NOE J 0.015 0.020 0.380 0.500 J E
imensions SOT-223 1.5 (0.059 ) 1.5 (0.059 ) 1.2 (0.047 ) (3x) 3.3 (0.130 ) 2.3 (0.091 ) 4.6 (0.181 ) imensions in Millimeters (Inches) Recommended Soldering ootprint for SOT223 imensions SOT-89 J 6.4 (0.252 ) J Tc Measuring Point B B Tc Measuring Point E imensions 0.001 0.004 0.02 0.10 E 0.114 0.118 0.124 2.90 3.00 J 3.15 0.024 0.027 0.034 0.60 0.70 0.85 0.090 2.30 H 0.181 Tc Measuring Point 4.60 B J I 0.264 0.276 0.287 6.70 7.0 0 7.30 J 0.009 0.010 0.014 0.24 0.26 0.35 E K 10 MX Inches Millimeters Min Typ Max Min Typ Max 0.248 0.256 0.264 6.30 6.50 6.70 B 0.130 0.138 0.146 3.30 3.50 3.70 0.071 1.80 Tc Measuri H B E H E H imension Inches Millimeters c Min Typ Max Min Typ g Max (0.91).036 Pad Layout for SOT-89 H (1.12).044 (1.19).047 (1.63).064 g (2.21).087 (1.63).064 (3.91).154 imensions in Millimeters (Inches) f c d a e g f c d a 0.173 0.181 4.40 4.60 B 0.090 c 0.102 2.29 2.60 0.055 g 0.155 0.063 0.167 1.40 3.94 f 1.60 4.25 E 0.035 0.047 e 0.89 a 1.20 0.056 f d0.062 1.42 1.57 b 0.115 0.121 2.92 3.07 e H 0.014 0.017 0.35 0.44 I 0.014 0.019 0.36 0.48 b J 0.064 0.072 1.62 1.83 d b e b
Product Selector Part Number 400V Voltage 600V 800V Sensitivity Package S4X8ES X 200 μ TO-92 S6X8ES X 200 μ TO-92 S8X8ES X 200 μ TO-92 S4X8TS X 200 μ SOT-223 S6X8TS X 200 μ SOT-223 S8X8TS X 200 μ SOT-223 S4X8BS X 200 μ SOT-89 S6X8BS X 200 μ SOT-89 S4X8ES1 X 5 μ TO-92 S6X8ES1 X 5 μ TO-92 S8X8ES1 X 5 μ TO-92 S4X8TS1 X 5 μ SOT-223 S6X8TS1 X 5 μ SOT-223 S8X8TS1 X 5 μ SOT-223 S4X8ES2 X 50 μ TO-92 S6X8ES2 X 50 μ TO-92 S8X8ES2 X 50 μ TO-92 S4X8TS2 X 50 μ SOT-223 S6X8TS2 X 50 μ SOT-223 S8X8TS2 X 50 μ SOT-223 Packing Options Part Number Marking Weight Packing Mode Base Quantity SxX8ESy SxX8ESy 0.217g Bulk 2500 SxX8ESyP SxX8ESy 0.217g mmo Pack 2000 SxX8ESyRP SxX8ESy 0.217g Tape & Reel 2000 SxX8TSyRP SxX8TSy 0.120g Tape & Reel 1000 SxX8BSRP xx8 0.053g Tape & Reel 1000 SxX8BSRP1 xx8 0.053g Tape & Reel 1000 Note: x = voltage, y = gate sensitivity
TO-92 (3-lead) Reel Pack (RP) Radial Leaded Specifications Meets all EI-468- Standards 1.6 (41.0) 0.236 (6.0) 0.02 (0.5) 0.098 (2.5) MX 1.26 (32.0) 0.708 (18.0) 0.354 (9.0) 0.5 (12.7) 0.1 (2.54) 14.17(360.0) 0.2 (5.08) 0.157 I (4.0) lat up 1.97 (50.0) irection of eed imensions are in inches (and millimeters). TO-92 (3-lead) mmo Pack (P) Radial Leaded Specifications Meets all EI-468- Standards 1.62 (41.2) 0.708 (18.0) 0.236 (6.0) 0.02 (0.5) 0.354 (9.0) 0.5 (12.7) irection of eed 0.1 (2.54) 0.2 (5.08) 0.098 (2.5) MX 0.157 I (4.0) lat down 1.27 (32.2) 25 evices per fold 1.85 (47.0) 12.2 (310.0) 1.85 (47.0) imensions are in inches (and millimeters). 13.3 (338.0)
SOT-89 Reel Pack (RP) Specifications Ø1.5 mm 4 mm 8 mm 2 mm NOE 1.75 mm 12 mm 5.5 mm TE NOE THOE 180 mm 13 mm bor Hole iameter 13.4 mm IRETION O EE SOT-89 Reel Pack (RP1) Specifications Ф 1.5mm 4mm 8mm 2mm THOE NOE 1.75mm 5.5mm 12mm NOE TE 180 mm 13 mm bor Hole iameter 13.4 mm IRETION O EE
SOT-223 Reel Pack (RP) Specifications 1.5 mm 4 mm 8 mm 2 mm 1.75 mm 12 mm 5.5 mm K TE 180 mm 13 mm bor Hole iameter 13.4 mm Part Numbering System Part Marking System SERIES S: SR VOLTE 4: 400V 6: 600V 8: 800V URRENT X8: 0.8 S xx8 x xx xx PKIN TYPE Blank: Bulk Pack RP: Reel Pack (TO-92) Embossed arrier Pack (SOT-223) Embossed arrier Pack (SOT-89) RP1: Embossed arrier Pack (SOT-89) (alternate orientation) P: mmo Pack (TO-92) SENSITIVITY & TYPE S1: 5µ Sensitive SR S2: 50µ Sensitive SR S: 200µ Sensitive SR PKE TYPE E: TO-92 T: SOT-223 B: SOT-89 SOT89 TO-92 SOT223 Line1 = Littelfuse Part Number Line2 = continuation Littelfuse Part Number Y = Last igit of alendar Year M = Letter Month ode (-L for Jan-ec) L = Location ode = alendar ate