SIACtor Series - TO-92 RoHS Pb e3 escription SIACtor Series TO-92 are designed to protect baseband equipment such as modems, line cards, CPE and SL from damaging overvoltage transients. The series provides a robust through-hole solution that enables equipment to comply with global regulatory standards. Features and Benefits Agency Approvals Agency Agency File Number E13383 Low voltage overshoot Low on-state voltage oes not degrade surge capability after multiple surge events within limit. Fails short circuit when surged in excess of ratings Low capacitance 2nd level interconnect is Pb-free per IPC/ JEEC J-ST-69A.1 Pinout esignation Schematic Symbol Pin 1 Pin 3 Applicable Global Standards TIA-968-A TIA-968-B ITU K.2/21 Enhanced Level* ITU K.2/21 Basic Level GR 189 Inter-building* GR 189 Intra-building IEC 61-4-5 Y/T 182 Y/T 993 Y/T 95 * A/B-rated parts require series resistance Electrical Characteristics @l RM =5µA @1V/µs @ =2.2 Amps Capacitance @1MHz, 2V bias Part Number Marking V min V max ma min ma max A max V max pf min pf max P8EALxxx P8EA 6 25 5 8 2.2 4 25 15 P3EALxxx P3EA 25 4 5 8 2.2 4 15 14 P64EALxxx P64EA 58 77 15 8 2.2 4 4 6 P72EALxxx P72EA 65 88 15 8 2.2 4 35 6 P9EALxxx P9EA 75 98 15 8 2.2 4 35 55 P11EALxxx P11EA 9 13 15 8 2.2 4 3 5 P13EALxxx P13EA 12 16 15 8 2.2 4 25 45 P15EALxxx P15EA 14 18 15 8 2.2 4 25 4 P18EALxxx P18EA 17 22 15 8 2.2 4 25 35 P23EALxxx P23EA 19 26 15 8 2.2 4 25 35 P26EALxxx P26EA 22 3 15 8 2.2 4 2 35 P31EALxxx P31EA 275 35 15 8 2.2 4 2 35 P35EALxxx P35EA 32 4 15 8 2.2 4 2 35 Table continues on next page.
Electrical Characteristics (continued Part Number Marking @l RM =5µA @1V/µs @ =2.2 Amps Capacitance @1MHz, 2V bias V Min V Max ma Min ma Max A Max V Max pf Min pf Max P8EBLxxx P8EB 6 25 5 8 2.2 4 25 15 P3EBLxxx P3EB 25 4 5 8 2.2 4 15 14 P64EBLxxx P64EB 58 77 15 8 2.2 4 4 6 P72EBLxxx P72EB 65 88 15 8 2.2 4 35 75 P9EBLxxx P9EB 75 98 15 8 2.2 4 35 7 P11EBLxxx P11EB 9 13 15 8 2.2 4 3 7 P13EBLxxx P13EB 12 16 15 8 2.2 4 25 6 P15EBLxxx P15EB 14 18 15 8 2.2 4 25 55 P18EBLxxx P18EB 17 22 15 8 2.2 4 25 5 xxx P23EB 19 26 15 8 2.2 4 25 5 P26EBLxxx P26EB 22 3 15 8 2.2 4 2 45 P31EBLxxx P31EB 275 35 15 8 2.2 4 2 45 P35EBLxxx P35EB 32 4 15 8 2.2 4 2 4 P8ECLxxx P8EC 6 25 5 8 2.2 4 35 26 P3ECLxxx P3EC 25 4 5 8 2.2 4 25 25 P64ECLxxx P64EC 58 77 15 8 2.2 4 55 155 P72ECLxxx P72EC 65 88 15 8 2.2 4 5 15 P9ECLxxx P9EC 75 98 15 8 2.2 4 45 14 P11ECLxxx P11EC 9 13 15 8 2.2 4 45 115 P13ECLxxx P13EC 12 16 15 8 2.2 4 4 15 P15ECLxxx P15EC 14 18 15 8 2.2 4 35 95 P18ECLxxx P18EC 17 22 15 8 2.2 4 35 9 P23ECLxxx P23EC 19 26 15 8 2.2 4 3 8 P26ECLxxx P26EC 22 3 15 8 2.2 4 3 8 P31ECLxxx P31EC 275 35 15 8 2.2 4 3 7 P35ECLxxx P35EC 32 4 15 8 2.2 4 25 65 - Absolute maximum ratings measured at T A = 25ºC (unless otherwise noted. - evices are bi-directional (unless otherwise noted. - xxx part number suffix: AP = Ammo Pack, RP1 and RP2 = Reel Pack, blank = Bulk Pack Surge Ratings Series I PP.2x31 1 2x1 1 8x2 1 1x16 1 1x56 1 5x32 1 1x36 1 1x1 1 5x31 1.5x7 2 2x1 2 1.2x5 2 1x16 2 1x56 2 9x72 2 1x36 2 1x1 2 1x7 2 ITSM 5/6 Hz A min A min A min A min A min A min A min A min A min A min A/µs max A 2 15 15 9 5 75 75 45 75 2 5 di/dt B 25 25 25 15 1 1 125 8 1 25 5 C 5 5 4 2 15 2 175 1 2 3 5 1 Current waveform in µs 2 Voltage waveform in µs - Peak pulse current rating (I PP is repetitive and guaranteed for the life of the product that remains in thermal equilibrium. - I PP ratings applicable over temperature range of -4ºC to +85ºC - The device must initially be in thermal equilibrium with -4 C < T J < +15 C Thermal Considerations Package Symbol Parameter Value Unit TO-92 T J Operating Junction Temperature Range -4 to +15 C T S Storage Temperature Range -65 to +15 C R JA Thermal Resistance: Junction to Ambient 9 C/W
Temperature SIACtor Protection Thyristors V-I Characteristics t r x t d Pulse Waveform +I -V I RM -I +V IPP Peak Pulse Current %IPP 1 5 t r Peak Value Waveform = t r x t d t d t r = rise time to peak value t d = decay time to half value Half Value t Time (µs Normalized Change vs. Junction Temperature Normalized C Holding Current vs. Case Temperature Percent of Change % 14 12 1 8 6 25 C 4 2-4 -6-8 -4-2 2 4 6 81 12 14 16 Junction Temperature (T J C (T C = 25ºC Ratio of 2. 1.8 1.6 1.4 1.2 1. 25 C.8.6.4-4 -2 2 4 6 8 1 12 14 16 Case Temperature (T C - ºC Soldering Parameters Reflow Condition Pb-Free assembly (see Fig. 1 - Temperature Min (T s(min +15 C Pre Heat - Temperature Max (T s(max +2 C - Time (Min to Max (t s 6-18 secs. Average ramp up rate (Liquidus Temp (T L to peak 3 C/sec. Max. T S(max to T L - Ramp-up Rate 3 C/sec. Max. Reflow - Temperature (T L (Liquidus +217 C - Temperature (t L 6-15 secs. T P T L T S(max T S(min Preheat t S Figure 1 Ramp-up t P t L Critical Zone TL to TP Ramp-down Peak Temp (T P Time within 5 C of actual Peak Temp (t p Ramp-down Rate Time 25 C to Peak Temp (T P o not exceed +26(+/-5 C 3 secs. Max. 6 C/sec. Max. 8 min. Max. +26 C 25 time to peak temperature (t 25ºC to peak Time
Physical Specifications Environmental Specifications Lead Material Terminal Finish Body Material Copper Alloy 1% Matte-Tin Plated UL recognized epoxy meeting flammability classification 94V- High Temp Voltage Blocking Temp Cycling Biased Temp & Humidity 8% Rated (V AC Peak +125 C or +15 C, 54 or 18 hrs. MIL-ST-75 (Method 14 JEEC, JES22-A-11-65 C to +15 C, 15 min. dwell, 1 up to 1 cycles. MIL-ST-75 (Method 151 EIA/JEEC, JES22-A14 52 V C (+85 C 85%RH, 54 up to 18 hrs. EIA/ JEEC, JES22-A-11 High Temp Storage +15 C 18 hrs. MIL-ST-75 (Method 131 JEEC, JES22-A-11 Low Temp Storage -65 C, 18 hrs. Thermal Shock C to +1 C, 5 min. dwell, 1 sec. transfer, 1 cycles. MIL-ST-75 (Method 156 JEEC, JES22-A-16 Autoclave (Pressure Cooker Test +121 C, 1%RH, 2atm, 24 up to 168 hrs. EIA/ JEEC, JES22-A-12 Resistance to Solder Heat +26 C, 3 secs. MIL-ST-75 (Method 231 Moisture Sensitivity Level 85%RH, +85 C, 168 hrs., 3 reflow cycles (+26 C Peak. JEEC-J-ST-2, Level 1 Part Numbering Part Marking TYPE P = SIACtor MEIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE P xxx ExLxxx PACKING OPTIONS RoHS COMPLIANT I PP RATING XXXXXXX XX XXXXX Part Marking Code (Refer to Electrical Characteristics Table ate Code Packing Options Package Type escription Packing Options Quantity Added Suffix Lead Spacing Industry Standard E RP1.1 inch (2.54mm TO-92 Tape and Reel Pack EIA-481- RP2.2 inch (5.8mm 2 TO-92 Ammo Pack AP EIA-468-B TO-92 Bulk Pack N/A N/A Additional Information atasheet Resources Samples
imensions TO-92 Ammo Pack Specification TO-92 MT1/PIN 1 M L Temperature Measurement Point E K J MT2/PIN 3 The TO-92 is designed to meet mechanical standards as set forth in JEEC publication number 95. H N A B G Min Max Min Max A.176.196 4.47 4.98 B.5 12.7.95.15 2.41 2.67 E.15 3.81 G.135.145 3.43 3.68 H.88.96 2.23 2.44 J.176.186 4.47 4.73 K.88.96 2.23 2.44 L.13.19.33.48 M.13.17.33.43 N.6 1.52 All leads are insulated from case. Case is electrically non-conductive. (Rated at 16 V (AC RMS for one minute from leads to case over the operating temperature range. Mold flash shall not exceed.13 mm per side. 1.62.236 (41.2 (6. MAX.78 (18..2 (.5.354 (9..5 (12.7.5 (12.7 irection of Feed imensions are in inches (and millimeters. 12.9 (327.25 (6.35.2 (5.8.125 (3.2 MAX 1.27 (32.2 25 evices per fold.157 IA (4. Flat down 1.7 (43 6.9 (175 1.7 (43 Tape and Reel Specification TO-92 FLAT SIE OF TO-92 imensions Min Max Min Max A N/A 14.173 N/A 36. B 4.16 N/A 12. N/A A C B W1 C 3.386 N/A 86. N/A.795 N/A 2.2 N/A W1 1.181 1.968 3. 5. P.496.54 12.6 12.8 P ROUN SIE OF TO-92 P.498.52 12.65 12.75 F(for RP1.9.11 2.29 2.8 F(for RP2.182.244 4.63 6.19 H H1 W2 W W3 W4 (RP1 (RP2 H N/A 1.673 N/A 42.5 H1 N/A 1.27 N/A 32.26 W.674.763 17.12 19.38 W2.354.37 8.25 9.75 W3.236 N/A 6. N/A P F F W4.2 N/A.5 N/A imension Minimum Maximum Minimum Maximum A N/A 14.173 N/A 36. B 4.16 N/A 12. N/A C 3.386 N/A 86. N/A Specifications.795 are subject N/A to change without 2.2 notice. N/A W1 1.181 1.968 3. 5. P.496.54 12.6 12.8