High and Low Side Driver
|
|
|
- Brent Dixon
- 7 years ago
- Views:
Transcription
1 High and Low Side Driver Features Product Summary Floating channel designed for bootstrap operation Fully operational to 200V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 10 to 20V Independent low and high side channels Input logic HIN/LIN active high Undervoltage lockout for both channels 3.3V and 5V logic compatible CMOS Schmitt-triggered inputs with pull-down Matched propagation delay for both channels V OFFSET (max) 200V I O+/- (typ) 1.0A / 1.0A V OUT t on/off (typ) Delay Matching (max) 10 20V 80ns & 60ns 20ns Description The IR2011 is a high power, high speed power MOSFET driver with independent high and low side referenced output channels. Logic inputs are compatible with standard CMOS or LSTTL output, down to 3.0V logic. The output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. Propagation delays are matched to simplify use in high frequency applications. The floating channel can be used to drive an N-channel power MOSFET in the high side configuration which operates up to 200 volts. Proprietary HVIC and latch immune CMOS technologies enable ruggedized monolithic construction. Applications Package Options 8-Lead PDIP 8-Lead SOIC Converters DC motor drive Ordering Information Base Part Number Package Type Standard Pack Form Quantity Orderable Part Number IR2011PBF PDIP8 Tube 50 IR2011PBF IR2011SPBF SO8N Tube 95 IR2011SPBF IR2011SPBF SO8N Tape and Reel 2500 IR2011STRPBF International Rectifier April 14, 2015
2 Typical Connection Diagram (Refer to Lead Assignments for correct configuration.) This diagram shows electrical connections only. Please refer to our Application Notes and Design Tips for proper circuit board layout International Rectifier April 14, 2015
3 Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to COM. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions. Symbol Definition Min. Max. Units V B High side floating supply voltage V S High side floating supply offset voltage V B - 25 V B V HO High side floating output voltage V S V B V CC Low side fixed supply voltage V V LO Low side output voltage -0.3 V CC V IN Logic input voltage (HIN, LIN) -0.3 V CC dv s /dt Allowable offset supply voltage transient 50 V/ns P D Package power T A +25 C Thermal resistance, junction to ambient 8-Lead PDIP Lead SOIC Lead PDIP 125 Rth JA 8-Lead SOIC 200 T J Junction temperature 150 T S Storage temperature T L Lead temperature (soldering, 10 seconds) 300 W C/W C Recommended Operating Conditions For proper operation the device should be used within the recommended conditions. The V S and COM offset ratings are tested with all supplies biased at 15V differential. Symbol Definition Min. Max. Units V B High side floating supply absolute voltage V S + 10 V S + 20 V S High side floating supply offset voltage 200 V HO High side floating output voltage V S V B V CC Low side fixed supply voltage V LO Low side output voltage 0 V CC V IN Logic input voltage (HIN, LIN) COM 5.5 T A Ambient temperature C Logic operational for V S of -4 to +200V. Logic state held for V S of -4V to -V BS. V International Rectifier April 14, 2015
4 Dynamic Electrical Characteristics V BIAS (V CC, V BS ) = 15V, C L = 1000pF and T A = 25 C unless otherwise specified. Figure 1 shows the timing definitions. Symbol Definition Min. Typ. Max. Units Test Conditions t on Turn-on propagation delay 80 V S = 0V t off Turn-off propagation delay 75 V S = 200V t r Turn-on rise time t f Turn-off fall time ns DM1 Turn-on delay matching t on (H) - t on (L) 20 DM2 Turn-off delay matching t off (H) - t off (L) 20 Static Electrical Characteristics V BIAS (V CC, V BS ) = 15V and T A = 25 C unless otherwise specified. The V IN, V TH and I IN parameters are referenced to COM and are applicable to all logic input leads: HIN and LIN. The V O and I O parameters are referenced to COM and are applicable to the respective output leads: HO or LO. Symbol Definition Min. Typ. Max. Units Test Conditions V IH Logic 1 input voltage 2.2 V CC = 10V 20V V IL Logic 0 input voltage 0.7 V V OH High level output voltage, V BIAS - V O 2.0 I O = 0A V OL Low level output voltage, V O 0.2 I O = 20mA I LK Offset supply leakage current 50 V B = V S = 200V I QBS Quiescent V BS supply current I QCC Quiescent V CC supply current μa V IN = 0V or 3.3V I IN+ Logic 1 input bias current V IN = 3.3V I IN- Logic 0 input bias current 1.0 V IN = 0V V BS supply undervoltage positive going threshold V BSUV+ V BSUV- V CCUV+ V CCUV- I O+ I O- V BS supply undervoltage negative going threshold V CC supply undervoltage positive going threshold V CC supply undervoltage negative going threshold Output high short circuit pulsed current Output low short circuit pulsed current V A V O = 0V, PW 10 μs V O = 15V PW 10 μs International Rectifier April 14, 2015
5 Functional Block Diagram International Rectifier April 14, 2015
6 Lead Definitions Symbol Description HIN Logic input for high side gate driver outputs (HO), in phase LIN Logic input for low side gate driver outputs (LO), in phase V B High side floating supply HO High side gate drive output V S High side floating supply return V CC Low side supply LO Low side gate drive output COM Low side return Lead Assignments 8-Lead PDIP 8-Lead SOIC International Rectifier April 14, 2015
7 Application Information and Additional Details Figure 1. Timing Diagram International Rectifier April 14, 2015
8 Figure 2A. Turn-on Propagation Delay vs. Temperature Figure 2B. Turn-on Propagation Delay vs. Supply Voltage Figure 3A. Turn-off Propagation Delay vs. Temperature Figure 3B. Turn-off Propagation Delay vs. Supply Voltage Figure 4A. Turn-on Rise Time vs. Temperature Figure 4B. Turn-on Rise Time vs. Supply Voltage International Rectifier April 14, 2015
9 Figure 5A. Turn-off Fall Time vs. Temperature Figure 5B. Turn-off Fall Time vs. Supply Voltage Figure 6A. Turn-on Delay Matching vs. Temperature Figure 6B. Turn-on Delay Matching Time vs. Supply Voltage Figure 7A. Turn-off Delay Matching Time vs. Temperature Figure 7B. Turn-off Delay Matching Time vs. Supply Voltage International Rectifier April 14, 2015
10 Figure 8A. Logic 1 Input Voltage vs. Temperature Figure 8B. Logic 1 Input Voltage vs. Supply Voltage Figure 9A. Logic 0 Input Voltage vs. Temperature Figure 9B. Logic 0 Input Voltage vs. Supply Voltage Figure 10A. High Level Output vs. Temperature Figure 10B. High Level Output vs. Supply Voltage International Rectifier April 14, 2015
11 Figure 11A. Low Level Output vs. Temperature Figure 11B. Low Level Output vs. Supply Voltage Figure 12A. Offset Supply Leakage Current vs. Temperature Figure 12B. Offset Supply Leakage Current vs. Supply Voltage Figure 13A. V BS Supply Current vs. Temperature Figure 13B. V BS Supply Current vs. Supply Voltage International Rectifier April 14, 2015
12 Figure 14A. V CC Supply Current vs. Temperature Figure 14B. V CC Supply Current vs. V CC Supply Voltage Figure 15A. Logic 1 Input Bias Current vs. Temperature Figure 15 B. Logic 1 Input Bias Current vs. Supply Voltage Figure 16A. Logic 0 Input Bias Current vs. Temperature Figure 16B. Logic 0 Input Bias Current vs. Supply Voltage International Rectifier April 14, 2015
13 Figure 17. V CC and V BS Undervoltage Threshold (+) vs. Temperature Figure 18. V CC and V BS Undervoltage Threshold (-) vs. Temperature Figure 19A. Output Source Current vs. Temperature Figure 19B. Output Source Current vs. Supply Voltage Figure 20A. Output Sink Current vs. Temperature Figure 20B. Output Sink Currnt vs. Supply Voltage International Rectifier April 14, 2015
14 Figure 21. Maximum V S Negative Offset vs. V BS Floating Supply Voltage International Rectifier April 14, 2015
15 Package Details International Rectifier April 14, 2015
16 Tape and Reel Details LOADED TAPE FEED DIRECTION B A H D F C NOTE : CONTROLLING DIMENSION IN MM E G CARRIER TAPE DIMENSION FOR 8SOICN Metric Imperial Code Min Max Min Max A B C D E F G 1.50 n/a n/a H F D E C B A G H REEL DIMENSIONS FOR 8SOICN Metric Imperial Code Min Max Min Max A B C D E F n/a n/a G H International Rectifier April 14, 2015
17 Part Marking Information Part number IRxxxxx Date code YWW? IR logo Pin 1 Identifier? P MARKING CODE Lead Free Released Non-Lead Free Released? XXXX Lot Code (Prod mode 4 digit SPN code) Assembly site code Per SCOP International Rectifier April 14, 2015
18 Qualification Information Qualification Level Moisture Sensitivity Level RoHS Compliant 8-Lead SOIC Industrial (per JEDEC JESD 47) Comments: This family of ICs has passed JEDEC s Industrial qualification. IR s Consumer qualification level is granted by extension of the higher Industrial level. MSL2 (per IPC/JEDEC J-STD-020) Yes Qualification standards can be found at International Rectifier s web site Higher qualification ratings may be available should the user have such requirements. Please contact your International Rectifier sales representative for further information. Higher MSL ratings may be available for the specific package types listed here. Please contact your International Rectifier sales representative for further information. The information provided in this document is believed to be accurate and reliable. However, International Rectifier assumes no responsibility for the consequences of the use of this information. International Rectifier assumes no responsibility for any infringement of patents or of other rights of third parties which may result from the use of this information. No license is granted by implication or otherwise under any patent or patent rights of International Rectifier. The specifications mentioned in this document are subject to change without notice. This document supersedes and replaces all information previously supplied. For technical support, please contact IR s Technical Assistance Center WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California Tel: (310) International Rectifier April 14, 2015
IRS2004(S)PbF HALF-BRIDGE DRIVER. Features. Product Summary. Packages
Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from V to V Undervoltage lockout. V, V,
IR2110(-1-2)(S)PbF/IR2113(-1-2)(S)PbF HIGH AND LOW SIDE DRIVER Product Summary
Data Sheet No. PD6147 rev.u Features Floating channel designed for bootstrap operation Fully operational to +5V or +6V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1
IR2110(S)/IR2113(S) & (PbF)
Data Sheet No. PD6147 Rev.T Features Floating channel designed for bootstrap operation Fully operational to +5V or +6V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1
CURRENT LIMITING SINGLE CHANNEL DRIVER V OFFSET. Packages
Features Floating channel designed for bootstrap operation Fully operational to +5V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 12 to 18V Undervoltage lockout Current
IR2117(S)/IR2118(S) & (PbF)
Data Sheet No. PD14 Rev N IR2117(S)/IR211(S) & (PbF) Features Floating channel designed for bootstrap operation Fully operational to +V Tolerant to negative transient voltage dv/dt immune Gate drive supply
V OUT. I o+ & I o- (typical) 2.3A & 3.3A. Package Type
July 25 th, 2012 Automotive Grade AUIRS4427S DUAL LOW SIDE DRIVER Features Gate drive supply range from 6 V to 20 V CMOS Schmitt-triggered inputs 3.3V and 5V logic compatible Two independent gate drivers
IR2130/IR2132(J)(S) & (PbF)
Data Sheet No. PD619 Rev.P Features Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1 to 2V Undervoltage
SELF-OSCILLATING HALF-BRIDGE DRIVER
Data Sheet No. PD60029 revj I2155&(PbF) (NOTE: For new designs, we recommend I s new products I2153 and I21531) SELF-OSCILLATING HALF-BIDGE DIE Features Floating channel designed for bootstrap operation
IR2109(4) (S) HALF-BRIDGE DRIVER. Features. Product Summary. Packages. Description. Typical Connection
Data Sheet No. PD66-T Features Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from to V Undervoltage
IRS2453(1)D(S) Product Summary
Features Integrated 600 V full-bridge gate driver CT, RT programmable oscillator 15.6 V Zener clamp on V CC Micropower startup Logic level latched shutdown pin Non-latched shutdown on CT pin (1/6th V CC
IR2233/IR2235(J&S) & (PbF)
Features Floating channel designed for bootstrap operation Fully operational to +6V or+v Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1V/V to 2V DC and up to 25V for
IR1168S DUAL SMART RECTIFIER DRIVER IC
Datasheet No PD97382 September 26, 2011 IR1168S DUAL SMART RECTIFIER DRIVER IC Features Secondary-side high speed controller for synchronous rectification in resonant half bridge topologies 200V proprietary
IRS2092 PROTECTED DIGITAL AUDIO AMPLIFIER. Product Summary
PROTECTED DIGITAL AUDIO AMPLIFIER Features Integrated analog input Class D audio amplifier driver in a small 16 pin package Floating inputs enable easy half bridge implementation Programmable bidirectional
IR2154 SELF-OSCILLATING HALF-BRIDGE DRIVER. Features. Product Summary. Packages. Description. Typical Connection V OFFSET
Features Integrated 600V half-bridge gate driver 15.6V zener clamp on Vcc True micropower start up Tighter initial deadtime control Low temperature coefficient deadtime Shutdown feature (1/6th Vcc) on
Lower Conduction Losses Low Thermal Resistance to PCB ( 0.5 C/W)
PD -97428 IRFH5020PbF HEXFET Power MOSFET V DS 200 V 55 m: R DS(on) max (@V GS = V) Q g (typical) 36 nc R G (typical).9 : I D (@T c(bottom) = 25 C) 43 A PQFN 5X6 mm Applications Secondary Side Synchronous
A I DM. W/ C V GS Gate-to-Source Voltage ± 20. Thermal Resistance Symbol Parameter Typ. Max. Units
V DS 2 V V GS Max ± 2 V R DSon) max @V GS = V) 24 m * PD - 9787A HEXFET Power MOSFET R DSon) max @V GS = 4.V) 4 m 6 Micro3 TM SOT-23) Applications) Load System Switch Features and Benefits Features Benefits
IRF6201PbF. HEXFET Power MOSFET V DS 20 V. R DS(on) max. 2.75 mω. Q g (typical) 130 nc 27 A. Absolute Maximum Ratings
PD - 97500A IRF620PbF V DS 20 V HEXFET Power MOSFET R DS(on) max (@ = 4.5V) 2.45 mω 6 R DS(on) max (@ = 2.5V) 2.75 mω 6 6 Q g (typical) 30 nc * SO-8 I D (@T A = 25 C) 27 A Applications OR-ing or hot-swap
IRLR8729PbF IRLU8729PbF
Applications l High Frequency Synchronous Buck Converters for Computer Processor Power l High Frequency Isolated DC-DC Converters with Synchronous Rectification for Telecom and Industrial Use Benefits
L6384E. High voltage half-bridge driver. Description. Features. Applications
High voltage half-bridge driver Description Datasheet - production data Features High voltage rail up to 600 V dv/dt immunity ± 50 V/nsec in full temperature range Driver current capability 400 ma source
CD4001BC/CD4011BC Quad 2-Input NOR Buffered B Series Gate Quad 2-Input NAND Buffered B Series Gate
CD4001BC/CD4011BC Quad 2-Input NOR Buffered B Series Gate Quad 2-Input NAND Buffered B Series Gate General Description The CD4001BC and CD4011BC quad gates are monolithic complementary MOS (CMOS) integrated
MM74HC14 Hex Inverting Schmitt Trigger
MM74HC14 Hex Inverting Schmitt Trigger General Description The MM74HC14 utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as
A I DM. W/ C V GS Gate-to-Source Voltage ± 12. Thermal Resistance Symbol Parameter Typ. Max. Units
V DS 2 V V GS Max ±2 V * PD - 973A HEXFET Power MOSFET R DSon) max @V GS = 4.V) 2. m R DSon) max @V GS = 2.V) 27. m 6 Micro3 TM SOT-23) Applications) Load System Switch Features and Benefits Features Benefits
RoHS Compliant Containing no Lead, no Bromide and no Halogen. IRF9310PbF SO8 Tube/Bulk 95 IRF9310TRPbF SO8 Tape and Reel 4000
PD 97437A IRF93PbF HEXFET Power MOSFET V DS 30 V R DS(on) max (@V GS = V) I D (@T A = 25 C) 4. mω 20 A * SO8 Applications Charge and Discharge Switch for Notebook PC Battery Application Features and Benefits
ISL6700. 80V/1.25A Peak, Medium Frequency, Low Cost, Half-Bridge Driver. Features. Ordering Information. Applications. Pinouts
ISL6700 Data Sheet FN9077.6 80V/1.25A Peak, Medium Frequency, Low Cost, Half-Bridge Driver The ISL6700 is an 80V/1.25A peak, medium frequency, low cost, half-bridge driver IC available in 8-lead SOIC and
MM74HC273 Octal D-Type Flip-Flops with Clear
MM74HC273 Octal D-Type Flip-Flops with Clear General Description The MM74HC273 edge triggered flip-flops utilize advanced silicon-gate CMOS technology to implement D-type flipflops. They possess high noise
C Soldering Temperature, for 10 seconds 300 (1.6mm from case )
l Advanced Process Technology l Ultra Low On-Resistance l Dynamic dv/dt Rating l 75 C Operating Temperature l Fast Switching l Fully Avalanche Rated l Optimized for SMPS Applications Description Advanced
MM74HC4538 Dual Retriggerable Monostable Multivibrator
MM74HC4538 Dual Retriggerable Monostable Multivibrator General Description The MM74HC4538 high speed monostable multivibrator (one shots) is implemented in advanced silicon-gate CMOS technology. They feature
MM74HC174 Hex D-Type Flip-Flops with Clear
Hex D-Type Flip-Flops with Clear General Description The MM74HC174 edge triggered flip-flops utilize advanced silicon-gate CMOS technology to implement D-type flipflops. They possess high noise immunity,
AAT4280 Slew Rate Controlled Load Switch
General Description Features SmartSwitch The AAT4280 SmartSwitch is a P-channel MOSFET power switch designed for high-side load switching applications. The P-channel MOSFET device has a typical R DS(ON)
MM74HCT373 MM74HCT374 3-STATE Octal D-Type Latch 3-STATE Octal D-Type Flip-Flop
3-STATE Octal D-Type Latch 3-STATE Octal D-Type Flip-Flop General Description The MM74HCT373 octal D-type latches and MM74HCT374 Octal D-type flip flops advanced silicongate CMOS technology, which provides
1 TO 4 CLOCK BUFFER ICS551. Description. Features. Block Diagram DATASHEET
DATASHEET 1 TO 4 CLOCK BUFFER ICS551 Description The ICS551 is a low cost, high-speed single input to four output clock buffer. Part of IDT s ClockBlocks TM family, this is our lowest cost, small clock
HCF4001B QUAD 2-INPUT NOR GATE
QUAD 2-INPUT NOR GATE PROPAGATION DELAY TIME: t PD = 50ns (TYP.) at V DD = 10V C L = 50pF BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20V
Features. Symbol JEDEC TO-220AB
Data Sheet June 1999 File Number 2253.2 3A, 5V,.4 Ohm, N-Channel Power MOSFET This is an N-Channel enhancement mode silicon gate power field effect transistor designed for applications such as switching
CD4001BC/CD4011BC Quad 2-Input NOR Buffered B Series Gate Quad 2-Input NAND Buffered B Series Gate
Quad 2-Input NOR Buffered B Series Gate Quad 2-Input NAND Buffered B Series Gate General Description The CD4001BC and CD4011BC quad gates are monolithic complementary MOS (CMOS) integrated circuits cotructed
CD4013BC Dual D-Type Flip-Flop
CD4013BC Dual D-Type Flip-Flop General Description The CD4013B dual D-type flip-flop is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P-channel enhancement mode transistors.
AUIPS71411G CURRENT SENSE HIGH SIDE SWITCH
February, 21st 2010 Automotive grade AUIPS71411G CURRENT SENSE HIGH SIDE SWITCH Features Suitable 24V battery operation Over current shutdown Over temperature shutdown Current sensing Active clamp Low
HCF4010B HEX BUFFER/CONVERTER (NON INVERTING)
HEX BUFFER/CONVERTER (NON INVERTING) PROPAGATION DELAY TIME: t PD = 50ns (Typ.) at V DD = 10V C L = 50pF HIGH TO LOW LEVEL LOGIC CONVERSION MULTIPLEXER: 1 TO 6 OR 6 TO 1 HIGH "SINK" AND "SOURCE" CURRENT
AP1509. 150KHz, 2A PWM BUCK DC/DC CONVERTER. Description. Pin Assignments V IN. Applications. Features. (Top View) GND GND. Output AP1509 GND GND
Description Pin Assignments The series are monolithic IC designed for a stepdown DC/DC converter, and own the ability of driving a 2A load without additional transistor. It saves board space. The external
AP331A XX G - 7. Lead Free G : Green. Packaging (Note 2)
Features General Description Wide supply Voltage range: 2.0V to 36V Single or dual supplies: ±1.0V to ±18V Very low supply current drain (0.4mA) independent of supply voltage Low input biasing current:
CD4027BC Dual J-K Master/Slave Flip-Flop with Set and Reset
October 1987 Revised March 2002 CD4027BC Dual J-K Master/Slave Flip-Flop with Set and Reset General Description The CD4027BC dual J-K flip-flops are monolithic complementary MOS (CMOS) integrated circuits
AP1506. 150KHz, 3A PWM BUCK DC/DC CONVERTER. Pin Assignments. Description. Features. Applications. ( Top View ) 5 SD 4 FB 3 Gnd 2 Output 1 V IN
Description Pin Assignments The series are monolithic IC designed for a stepdown DC/DC converter, and own the ability of driving a 3A load without external transistor. Due to reducing the number of external
CD4043BC CD4044BC Quad 3-STATE NOR R/S Latches Quad 3-STATE NAND R/S Latches
CD4043BC CD4044BC Quad 3-STATE NOR R/S Latches Quad 3-STATE NAND R/S Latches General Description The CD4043BC are quad cross-couple 3-STATE CMOS NOR latches, and the CD4044BC are quad cross-couple 3- STATE
DM74LS157 DM74LS158 Quad 2-Line to 1-Line Data Selectors/Multiplexers
September 1986 Revised April 2000 DM74LS157 DM74LS158 Quad 2-Line to 1-Line Data Selectors/Multiplexers General Description These data selectors/multiplexers contain inverters and drivers to supply full
TSM2N7002K 60V N-Channel MOSFET
SOT-23 SOT-323 Pin Definition: 1. Gate 2. Source 3. Drain PRODUCT SUMMARY V DS (V) R DS(on) (Ω) I D (ma) 5 @ V GS = 10V 100 60 5.5 @ V GS = 5V 100 Features Low On-Resistance ESD Protection High Speed Switching
DM74121 One-Shot with Clear and Complementary Outputs
June 1989 Revised July 2001 DM74121 One-Shot with Clear and Complementary Outputs General Description The DM74121 is a monostable multivibrator featuring both positive and negative edge triggering with
Description. Table 1. Device summary. Order code Temperature range Package Packaging Marking
14-stage ripple carry binary counter/divider and oscillator Applications Automotive Industrial Computer Consumer Description Datasheet - production data Features Medium speed operation Common reset Fully
MC74HC132A. Quad 2-Input NAND Gate with Schmitt-Trigger Inputs. High Performance Silicon Gate CMOS
MC74HC32A Quad 2-Input NAND Gate with Schmitt-Trigger Inputs High Performance Silicon Gate CMOS The MC74HC32A is identical in pinout to the LS32. The device inputs are compatible with standard CMOS outputs;
Automotive Grade AUIRS2092S PROTECTED DIGITAL AUDIO AMPLIFIER
March 11, 2011 Automotive Grade AUIRS2092S PROTECTED DIGITAL AUDIO AMPLIFIER Features Integrated analog input Class D audio amplifier driver in a small 16 pin package Floating inputs enable easy half bridge
SLG7NT4129 PCIE RTD3. Pin Configuration. Features Low Power Consumption Dynamic Supply Voltage RoHS Compliant / Halogen-Free Pb-Free TDFN-12 Package
General Description Silego SLG7NT4129 is a low power and small form device. The SoC is housed in a 2.5mm x 2.5mm TDFN package which is optimal for using with small devices. Features Low Power Consumption
UNISONIC TECHNOLOGIES CO., LTD 50N06 Power MOSFET
UNISONIC TECHNOLOGIES CO., LTD 50N06 50 Amps, 60 Volts N-CHANNEL POWER MOSFET DESCRIPTION TO-263 TO-25 The UTC 50N06 is three-terminal silicon device with current conduction capability of about 50A, fast
C Soldering Temperature, for 10 seconds 300 (1.6mm from case )
dvanced Process Technology Dynamic dv/dt Rating 75 C Operating Temperature Fast Switching Fully valanche Rated Lead-Free Description Fifth Generation HEXFETs from International Rectifier utilize advanced
74AC139 74ACT139 Dual 1-of-4 Decoder/Demultiplexer
Dual 1-of-4 Decoder/Demultiplexer General Description The AC/ACT139 is a high-speed, dual 1-of-4 decoder/ demultiplexer. The device has two independent decoders, each accepting two inputs and providing
INTEGRATED CIRCUITS. 74LVC08A Quad 2-input AND gate. Product specification IC24 Data Handbook. 1997 Jun 30
INTEGRATED CIRCUITS IC24 Data Handbook 1997 Jun 30 FEATURES Wide supply voltage range of 1.2 V to 3.6 V In accordance with JEDEC standard no. 8-1A Inputs accept voltages up to 5.5 V CMOS low power consumption
3-Channel Supervisor IC for Power Supply
3-Channel Supervisor IC for Power Supply Features Over-voltage protection and lockout Under-voltage protection and lockout Open drain power good output signal Built-in 300mS delay for power good 38mS de-bounce
IRF150 [REF:MIL-PRF-19500/543] 100V, N-CHANNEL. Absolute Maximum Ratings
![IRF150 [REF:MIL-PRF-19500/543] 100V, N-CHANNEL. Absolute Maximum Ratings](/thumbs/40/21333646.jpg "IRF150 [REF:MIL-PRF-19500/543] 100V, N-CHANNEL. Absolute Maximum Ratings")
PD - 90337G REPETITIVE AVALANCHE AND dv/dt RATED HEXFET TRANSISTORS THRU-HOLE (TO-204AA/AE) Product Summary Part Number BVDSS RDS(on) ID IRF150 100V 0.055Ω 38A IRF150 JANTX2N6764 JANTXV2N6764 [REF:MIL-PRF-19500/543]
2.5 A Output Current IGBT and MOSFET Driver
VO. A Output Current IGBT and MOSFET Driver 9 DESCRIPTION NC A C NC _ The VO consists of a LED optically coupled to an integrated circuit with a power output stage. This optocoupler is ideally suited for
DM74LS00 Quad 2-Input NAND Gate
DM74LS00 Quad 2-Input NAND Gate General Description This device contains four independent gates each of which performs the logic NAND function. Ordering Code: August 1986 Revised March 2000 Order Number
ICS514 LOCO PLL CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET
DATASHEET ICS514 Description The ICS514 LOCO TM is the most cost effective way to generate a high-quality, high-frequency clock output from a 14.31818 MHz crystal or clock input. The name LOCO stands for
DM74LS191 Synchronous 4-Bit Up/Down Counter with Mode Control
August 1986 Revised February 1999 DM74LS191 Synchronous 4-Bit Up/Down Counter with Mode Control General Description The DM74LS191 circuit is a synchronous, reversible, up/ down counter. Synchronous operation
S112-XHS. Description. Features. Agency Approvals. Applications. Absolute Maximum Ratings. Schematic Diagram. Ordering Information
Description Features The S112-X is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay. The circuit is composed of one input IR LED with a series limiting resistor
IRF5305PbF. HEXFET Power MOSFET V DSS = -55V. R DS(on) = 0.06Ω I D = -31A
dvanced Process Technology Dynamic dv/dt Rating 75 C Operating Temperature Fast Switching PChannel Fully valanche Rated LeadFree Description Fifth Generation HEXFETs from International Rectifier utilize
DM74LS05 Hex Inverters with Open-Collector Outputs
Hex Inverters with Open-Collector Outputs General Description This device contains six independent gates each of which performs the logic INVERT function. The open-collector outputs require external pull-up
.OPERATING SUPPLY VOLTAGE UP TO 46 V
L298 DUAL FULL-BRIDGE DRIVER.OPERATING SUPPLY VOLTAGE UP TO 46 V TOTAL DC CURRENT UP TO 4 A. LOW SATURATION VOLTAGE OVERTEMPERATURE PROTECTION LOGICAL "0" INPUT VOLTAGE UP TO 1.5 V (HIGH NOISE IMMUNITY)
STPS20L15DPbF SCHOTTKY RECTIFIER. Case Styles. I F(AV) = 20Amp V R = 15V. Bulletin PD-20873 rev. A 02/07. Major Ratings and Characteristics
STPS20L5DPbF SCHOTTKY RECTIFIER 20 Amps I F(AV) = 20Amp V R = 5V Major Ratings and Characteristics Characteristics Values Units I F(AV) Rectangular 20 A waveform V RRM 5 V I FSM @ tp = 5 μs sine 700 A
HI-200, HI-201. Features. Dual/Quad SPST, CMOS Analog Switches. Applications. Ordering Information. Functional Diagram FN3121.9
Data Sheet FN3121.9 Dual/Quad SPST, CMOS Analog Switches HI-200/HI-201 (dual/quad) are monolithic devices comprising independently selectable SPST switches which feature fast switching speeds (HI-200 240ns,
CAT4109, CAV4109. 3-Channel Constant-Current RGB LED Driver with Individual PWM Dimming
3-Channel Constant-Current RGB LED Driver with Individual PWM Dimming Description The CAT419/CAV419 is a 3 channel constant current LED driver, requiring no inductor. LED channel currents up to 175 ma
DM7474 Dual Positive-Edge-Triggered D-Type Flip-Flops with Preset, Clear and Complementary Outputs
DM7474 Dual Positive-Edge-Triggered D-Type Flip-Flops with Preset, Clear and Complementary Outputs General Description This device contains two independent positive-edge-triggered D-type flip-flops with
CD40174BC CD40175BC Hex D-Type Flip-Flop Quad D-Type Flip-Flop
Hex D-Type Flip-Flop Quad D-Type Flip-Flop General Description The CD40174BC consists of six positive-edge triggered D- type flip-flops; the true outputs from each flip-flop are externally available. The
STPS40L15CW. 2 x 20 Amps SCHOTTKY RECTIFIER. Case Styles. I F(AV) = 40Amp V R = 15V. Bulletin PD-20622 rev. B 10/06. Description/ Features
Bulletin PD-20622 rev. B 0/06 STPS40L5CW SCHOTTKY RECTIFIER 2 x 20 Amps I F(AV) = 40Amp V R = 5V Major Ratings and Characteristics Characteristics Values Units I F(AV) Rectangular 40 A waveform V RRM 5
MADR-009190-0001TR. Quad Driver for GaAs FET or PIN Diode Switches and Attenuators Rev. 4. Functional Schematic. Features.
Features High Voltage CMOS Technology Four Channel Positive Voltage Control CMOS device using TTL input levels Low Power Dissipation Low Cost Lead-Free SOIC-16 Plastic Package Halogen-Free Green Mold Compound
FPAB20BH60B PFC SPM 3 Series for Single-Phase Boost PFC
FPAB20BH60B PFC SPM 3 Series for Single-Phase Boost PFC Features UL Certified No. E209204 (UL1557) 600 V - 20 A Single-Phase Boost PFC with Integral Gate Driver and Protection Very Low Thermal Resistance
1.5A ASYNCHRONOUS DC-DC BUCK CONV
General Description The is a 1.4MHz fixed frequency, current mode, PWM buck (step-down) DC-DC converter, capable of driving a 1.5A load with high efficiency, excellent line and load regulation. The device
AUTOMOTIVE MOSFET. C Soldering Temperature, for 10 seconds 300 (1.6mm from case )
PD 9399A AUTOMOTIVE MOSFET Typical Applications Electric Power Steering (EPS) Antilock Braking System (ABS) Wiper Control Climate Control Power Door Benefits Advanced Process Technology Ultra Low OnResistance
74F74 Dual D-Type Positive Edge-Triggered Flip-Flop
Dual D-Type Positive Edge-Triggered Flip-Flop General Description The F74 is a dual D-type flip-flop with Direct Clear and Set inputs and complementary (Q, Q) outputs. Information at the input is traferred
AUIRLR2905 AUIRLU2905
Features dvanced Planar Technology Logic Level Gate Drive Low On-Resistance Dynamic dv/dt Rating 175 C Operating Temperature Fast Switching Fully valanche Rated Repetitive valanche llowed up to Tjmax Lead-Free,
HCF4028B BCD TO DECIMAL DECODER
BCD TO DECIMAL DECODER BCD TO DECIMAL DECODING OR BINARY TO OCTAL DECODING HIGH DECODED OUTPUT DRIVE CAPABILITY "POSITIVE LOGIC" INPUTS AND OUTPUTS: DECODED OUTPUTS GO HIGH ON SELECTION MEDIUM SPEED OPERATION
L293B L293E PUSH-PULL FOUR CHANNEL DRIVERS. OUTPUT CURRENT 1A PER CHANNEL PEAK OUTPUT CURRENT 2A PER CHANNEL (non repetitive) INHIBIT FACILITY
L293B L293E PUSH-PULL FOUR CHANNEL DRIVERS OUTPUT CURRENT 1A PER CHANNEL PEAK OUTPUT CURRENT 2A PER CHANNEL (non repetitive) INHIBIT FACILITY. HIGH NOISE IMMUNITY SEPARATE LOGIC SUPPLY OVERTEMPERATURE
MASW-007070-0001TB. GaAs SPST Switch, Absorptive, Single Supply, DC-4.0 GHz. Features. Pin Configuration 1,2,3,4. Description. Ordering Information
Features Operates DC - 4 GHz on Single Supply ASIC TTL / CMOS Driver Low DC Power Consumption 50 Ohm Nominal Impedance Test Boards are Available Tape and Reel are Available Lead-Free 4 x 6 mm PQFN Package
HCF4081B QUAD 2 INPUT AND GATE
QUAD 2 INPUT AND GATE MEDIUM SPEED OPERATION : t PD = 60ns (Typ.) at 10 QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15 PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I = 100nA (MAX) AT DD = 18 T A = 25
HCF4070B QUAD EXCLUSIVE OR GATE
QUAD EXCLUSIE OR GATE MEDIUM-SPEED OPERATION t PHL = t PLH = 70ns (Typ.) at CL = 50 pf and DD = 10 QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15 PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I = 100nA
MC14008B. 4-Bit Full Adder
4-Bit Full Adder The MC4008B 4bit full adder is constructed with MOS PChannel and NChannel enhancement mode devices in a single monolithic structure. This device consists of four full adders with fast
74LS193 Synchronous 4-Bit Binary Counter with Dual Clock
74LS193 Synchronous 4-Bit Binary Counter with Dual Clock General Description The DM74LS193 circuit is a synchronous up/down 4-bit binary counter. Synchronous operation is provided by having all flip-flops
DM74LS151 1-of-8 Line Data Selector/Multiplexer
1-of-8 Line Data Selector/Multiplexer General Description This data selector/multiplexer contains full on-chip decoding to select the desired data source. The DM74LS151 selects one-of-eight data sources.
DM74LS153 Dual 1-of-4 Line Data Selectors/Multiplexers
Dual 1-of-4 Line Data Selectors/Multiplexers General Description Each of these data selectors/multiplexers contains inverters and drivers to supply fully complementary, on-chip, binary decoding data selection
3-PHASE-BRIDGE DRIVER
June 1 211 IRS233(,2)(D)(S & J)PbF 3-PHASE-BRIDGE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +6 V Tolerant to negative transient voltage dv/dt immune Gate drive
SPREAD SPECTRUM CLOCK GENERATOR. Features
DATASHEET ICS7152 Description The ICS7152-01, -02, -11, and -12 are clock generators for EMI (Electro Magnetic Interference) reduction (see below for frequency ranges and multiplier ratios). Spectral peaks
TYPICAL APPLICATION CIRCUIT. ORDER INFORMATION SOP-EP 8 pin A703EFT (Lead Free) A703EGT (Green)
www.addmtek.com 2 CHANNELS 150mA HIGH VOLTAGE ADJUSTABLE CURRENT REGULATOR DESCRIPTION A703 is a high voltage, adjustable constant current driver for LED applications. Two regulated current ports are designed
IRGP4068DPbF IRGP4068D-EPbF
INSULATED GATE BIPOLAR TRANSISTOR WITH ULTRA-LOW VF DIODE FOR INDUCTION HEATING AND SOFT SWITCHING APPLICATIONS Features Low V CE (ON) Trench IGBT Technology Low Switching Losses Maximum Junction temperature
400KHz 60V 4A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter
Features Wide 5V to 32V Input Voltage Range Positive or Negative Output Voltage Programming with a Single Feedback Pin Current Mode Control Provides Excellent Transient Response 1.25V reference adjustable
74VHC574 Octal D-Type Flip-Flop with 3-STATE Outputs
74HC574 Octal D-Type Flip-Flop with 3-STATE Outputs General Description Ordering Code: March 1993 Revised May 2005 The HC574 is an advanced high speed CMOS octal flipflop with 3-STATE output fabricated
NTMS4920NR2G. Power MOSFET 30 V, 17 A, N Channel, SO 8 Features
NTMS9N Power MOSFET 3 V, 7 A, N Channel, SO Features Low R DS(on) to Minimize Conduction Losses Low Capacitance to Minimize Driver Losses Optimized Gate Charge to Minimize Switching Losses These Devices
10MQ100N SCHOTTKY RECTIFIER. I F(AV) = 2.1Amp V R = 100V. Bulletin PD-20520 rev. M 07/04. Major Ratings and Characteristics. Description/ Features
0MQ00N SCHOTTKY RECTIFIER 2. Amp I F(AV) = 2.Amp V R = 00V Major Ratings and Characteristics Characteristics 0MQ00N Units I F DC 2. A V RRM 00 V I FSM @ tp = 5 µs sine 20 A V F @.5Apk, T =25 C 0.68 V J
HCF4056B BCD TO 7 SEGMENT DECODER /DRIVER WITH STROBED LATCH FUNCTION
BCD TO 7 SEGMENT DECODER /DRIVER WITH STROBED LATCH FUNCTION QUIESCENT CURRENT SPECIF. UP TO 20V OPERATION OF LIQUID CRYSTALS WITH CMOS CIRCUITS PROVIDES ULTRA LOW POWER DISPLAY. EQUIVALENT AC OUTPUT DRIVE
STP80NF55-08 STB80NF55-08 STB80NF55-08-1 N-CHANNEL 55V - 0.0065 Ω - 80A D2PAK/I2PAK/TO-220 STripFET II POWER MOSFET
STP80NF55-08 STB80NF55-08 STB80NF55-08-1 N-CHANNEL 55V - 0.0065 Ω - 80A D2PAK/I2PAK/TO-220 STripFET II POWER MOSFET TYPE V DSS R DS(on) I D STB80NF55-08/-1 STP80NF55-08 55 V 55 V
Power MOSFET FEATURES. IRFZ44PbF SiHFZ44-E3 IRFZ44 SiHFZ44 T C = 25 C
Power MOSFET PRODUCT SUMMARY (V) 60 R DS(on) (Ω) V GS = 10 V 0.028 Q g (Max.) (nc) 67 Q gs (nc) 18 Q gd (nc) 25 Configuration Single FEATURES Dynamic dv/dt Rating 175 C Operating Temperature Fast Switching
Features. Modulation Frequency (khz) VDD. PLL Clock Synthesizer with Spread Spectrum Circuitry GND
DATASHEET IDT5P50901/2/3/4 Description The IDT5P50901/2/3/4 is a family of 1.8V low power, spread spectrum clock generators capable of reducing EMI radiation from an input clock. Spread spectrum technique
MADR-009269-0001TR. Single Driver for GaAs FET or PIN Diode Switches and Attenuators Rev. V1. Functional Schematic. Features.
Features High Voltage CMOS Technology Complementary Outputs Positive Voltage Control CMOS device using TTL input levels Low Power Dissipation Low Cost Plastic SOIC-8 Package 100% Matte Tin Plating over
Power MOSFET FEATURES. IRL540PbF SiHL540-E3 IRL540 SiHL540
Power MOSFET PRODUCT SUMMARY (V) 100 R DS(on) (Ω) = 5.0 V 0.077 Q g (Max.) (nc) 64 Q gs (nc) 9.4 Q gd (nc) 27 Configuration Single TO220AB G DS ORDERING INFORMATION Package Lead (Pb)free SnPb G D S NChannel
TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER. Features
DATASHEET ICS280 Description The ICS280 field programmable spread spectrum clock synthesizer generates up to four high-quality, high-frequency clock outputs including multiple reference clocks from a low-frequency
ICS650-44 SPREAD SPECTRUM CLOCK SYNTHESIZER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS650-44 Description The ICS650-44 is a spread spectrum clock synthesizer intended for video projector and digital TV applications. It generates three copies of an EMI optimized 50 MHz clock