HI-200, HI-201. Features. Dual/Quad SPST, CMOS Analog Switches. Applications. Ordering Information. Functional Diagram FN3121.9

Transcription

1 Data Sheet FN Dual/Quad SPST, CMOS Analog Switches HI-200/HI-201 (dual/quad) are monolithic devices comprising independently selectable SPST switches which feature fast switching speeds (HI ns, and HI ns) combined with low power dissipation (15mW at 25 o C). Each switch provides low ON resistance operation for input signal voltage up to the supply rails and for signal current up to 80mA. Rugged DI construction eliminates latch-up and substrate SCR failure modes. All devices provide break-before-make switching and are TTL and CMOS compatible for maximum application versatility. HI-200/HI-201 are ideal components for use in high frequency analog switching. Typical applications include signal path switching, sample and hold circuit, digital filters, and operational amplifier gain switching networks. Ordering Information PART NUMBER HI Z (Note) (No longer available or supported) TEMP. RANGE ( C) PACKAGE 0 to Ld PDIP* (Pb-free) PKG. DWG. # E14.3 HI to Ld CERDIP F16.3 HI Z (Note) HI4P0201-5Z (Note) (No longer available or supported) HI9P0201-5Z (Note) HI9P0201-9Z (Note) 0 to Ld PDIP* (Pb-free) 0 to Ld PLCC (Pb-free) 0 to Ld SOIC (Pb-free) -40 to Ld SOIC (Pb-free) E16.3 N20.35 M16.15 M16.15 *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. Features Pb-Free Available (RoHS Compliant) Analog Voltage Range V Analog Current Range mA Turn-On Time ns Low r ON Low Power Dissipation mW TTL/CMOS Compatible Applications High Frequency Analog Switching Sample and Hold Circuits Digital Filters Operational Amplifier Gain Switching Networks Functional Diagram LOGIC REFEREE, LEVEL SHIFTER, AND DRIVER GATE TRUTH TABLE SWITCH CELL SOURCE DRAIN GATE LOGIC HI-200 HI ON ON 1 OFF OFF OUTPUT NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 0% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures INTERSIL or Intersil (and design) is a registered trademark of Intersil Americas LLC Copyright Intersil Americas LLC. 1999, 2001, 2004, 2005,2015. All Rights Reserved All other trademarks mentioned are the property of their respective owners.

2 Pinouts (Switches Shown For Logic 1 Input) HI-200 (PDIP) TOP VIEW HI-201 (CERDIP, PDIP, SOIC) TOP VIEW HI-201 (PLCC) TOP VIEW A 2 IN2 OUT A IN1 OUT1 NO LONGER AVAILABLE OR SUPPORTED A 1 OUT1 IN1 IN4 OUT4 A A 2 OUT2 IN2 IN3 OUT3 A 3 IN1 IN4 OUT1 A1 A2 OUT NO LONGER AVAILABLE OR SUPPORTED IN2 IN3 OUT4 A4 A3 OUT3 Schematic Diagrams TTL/CMOS REFEREE CIRCUIT CELL HI-200 TTL/CMOS REFEREE CIRCUIT CELL HI-201 R 2 5K QP2 R6 300 R 2 5K QP2 R6 600 QP1 QP3 Q N4 QP1 QP3 Q N4 M P13 Q N1 Q P4 Q P5 TO P 2 M P13 Q N1 Q P4 Q P5 TO P 2 D 3 R K M N14 D 3 R K M N14 Q N2 R 4 5.4K R 5 7.9K M N15 MN16 MN17 V LL R 7 0K Q N2 R 4 5.4K R 5 7.9K M P14 QN3 Q P6 M N15 MN16 MN17 V LL R 7 0K 2 FN3121.9

3 Schematic Diagrams (Continued) SWITCH CELL A Q N11 Q N12 Q P11 Q N13 OUTPUT Q P12 A DIGITAL BUFFER AND LEVEL SHIFTER Q P3 Q P5 Q P1 Q P4 A Q N1 D 1 QP6 Q P7 Q P8 QP9 Q P TO V LL 200 D 2 TO Q N6 Q N7 Q N8 Q N9 QN Q P2 A A Q N2 QN4 Q N5 Q N3 3 FN3121.9

4 Absolute Maximum Ratings Supply Voltage ( to ) V ( 22) to Ground V, -5V Digital Input Voltage () +4V to () -4V Analog Input Voltage (One Switch) () +2V to () -2V Operating Conditions Temperature Ranges HI o C to 125 o C HI o C to 85 o C HI-200-5, HI o C to 75 o C HI o C to 85 o C Thermal Information Thermal Resistance (Typical, Note 1) JA ( o C/W) JC ( o C/W) CERDIP Package PLCC Package N/A PDIP Package* N/A SOIC Package N/A Maximum Storage Temperature o C to 150 o C Maximum Junction Temperature (Hermetic Packages) o C Maximum Junction Temperature (Plastic Packages) o C Maximum Lead Temperature (Soldering, s) o C (PLCC and SOIC - Lead Tips Only) *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in reflow solder processing applications. CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. JA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications Supplies = +15V, -15V; = Open; V AH (Logic Level High) = 2.4V, VAL (Logic Level Low) = 0.8V PARAMETER TEST CONDITIONS TEMP ( o C) -2-4, -5, -9 MIN TYP MAX MIN TYP MAX UNITS DYNAMIC CHARACTERISTICS Switch ON Time, t ON HI ns HI ns Full ns Switch OFF Time, t OFF HI ns HI ns Off Isolation (Note 4) Full ns HI db HI db Input Switch Capacitance, C S(OFF) pf Output Switch Capacitance, C D(OFF) pf Output Switch Capacitance, C D(ON) pf Digital Input Capacitance, C A pf Drain-to-Source Capacitance, C DS(OFF) pf DIGITAL CHARACTERISTICS Input Low Threshold, V AL Full V Input High Threshold, V AH Full V Input Leakage Current (High or Low), I A (Note 3) Full A ANALOG SWITCH CHARACTERISTICS Analog Signal Range, V S Full V ON Resistance, r ON (Note 2) Full FN3121.9

5 Electrical Specifications Supplies = +15V, -15V; = Open; V AH (Logic Level High) = 2.4V, VAL (Logic Level Low) = 0.8V (Continued) PARAMETER TEST CONDITIONS TEMP ( o C) -2-4, -5, -9 MIN TYP MAX MIN TYP MAX UNITS OFF Input Leakage Current, I S(OFF) (Note 6) na HI-200 Full na HI na Full na OFF Output Leakage Current, I D(OFF) (Note 6) na HI-200 Full na HI na Full na ON Leakage Current, I D(ON) (Note 6) na HI-200 Full na HI na Full na POWER SUPPLY CHARACTERISTICS (Note 5) Power Dissipation, P D mw Full mw Current, I ma Full ma Current, I ma Full ma NOTES: 2. V OUT = V, I OUT = 1mA. 3. Digital Inputs are MOS gates: typical leakage is < 1nA. 4. V A = 5V, R L = 1k, C L = pf, V S = 3V RMS, f = 0kHz. 5. V A = +3V or V A = 0V for Both Switches. 6. Refer to Leakage Current Measurements (Figure 2). Test Circuits and Waveforms T A = 25 o C, V SUPPLY = ± 15V, V AH = 2.4V, V AL = 0.8V and = Open 1mA V 2 r ON = mA IN V 2 OUT V IN FIGURE 1A. ON RESISTAE TEST CIRCUIT 5 FN3121.9

6 Test Circuits and Waveforms T A = 25 o C, V SUPPLY = ± 15V, V AH = 2.4V, V AL = 0.8V and = Open (Continued) 80 0 ON RESISTAE ( ) V IN = 0V ON RESISTAE ( ) 50 = +V = -V = +15V = -15V = +12.5V = -12.5V TEMPERATURE ( o C) ANALOG SIGNAL LEVEL (V) FIGURE 1B. ON RESISTAE vs TEMPERATURE FIGURE 1C. HI-200 ON RESISTAE vs ANALOG SIGNAL LEVEL FIGURE 1. ON RESISTAE I S(OFF) I D(OFF) 0 A IN OUT A +14V 14V I S(OFF) / I D(OFF) CURRENT (na) 1.0 I D(ON) FIGURE 2B. OFF LEAKAGE CURRENT TEST CIRCUIT IN OUT TEMPERATURE ( o C) A I D(ON) 14V FIGURE 2A. LEAKAGE CURRENT vs TEMPERATURE FIGURE 2C. ON LEAKAGE CURRENT TEST CIRCUIT FIGURE 2. LEAKAGE CURRENTS SWITCH CURRENT (ma) IN OUT HI-201 I V IN VOLTAGE ACROSS SWITCH ( V) FIGURE 3A. SWITCH CURRENT vs VOLTAGE FIGURE 3. SWITCH CURRENT FIGURE 3B. TEST CIRCUIT 6 FN3121.9

7 Test Circuits and Waveforms T A = 25 o C, V SUPPLY = ± 15V, V AH = 2.4V, V AL = 0.8V and = Open (Continued) DIGITAL V AH = 4V 50% V AL = 0V 50% t ON t OFF 80% 80% SWITCH OUTPUT 0V FIGURE 4A. MEASUREMENT POINTS V A V A OUTPUT OUTPUT V A = 0 to 4V Vertical: 2V/Div. Horizontal: 0ns/Div. FIGURE 4B. WAVEFORMS WITH TTL COMPATIBLE LOGIC V A = 0 to 15V Vertical: 5V/Div. Horizontal: 0ns/Div. FIGURE 4C. WAVEFORMS WITH CMOS COMPATIBLE LOGIC FIGURE 4. SWITCH t ON AND t OFF 140 OFF ISOLATION (db) R L = 1k Hz 1kHz khz 0kHz 1MHz FREQUEY (Hz) FIGURE 5. HI-201 OFF ISOLATION vs FREQUEY For more information see Application Notes AN520, AN521, AN531, AN532 and AN FN3121.9

8 Application Information Single Supply Operation The switch operation of the HI-200/201 is dependent upon an internally generated switching threshold voltage optimized for 15V power supplies. The HI-200/201 does not provide the necessary internal switching threshold in a single supply system. Therefore, if single supply operation is required, the HI-300 series of switches is recommended. The HI-300 series will remain operational to a minimum +5V single supply. Switch performance will degrade as power supply voltage is reduced from optimum levels ( 15V). So it is recommended that a single supply design be thoroughly evaluated to ensure that the switch will meet the requirements of the application. For further information see Application Notes AN520, AN557, AN33 and AN34. 8 FN3121.9

9 Die Characteristics METALLIZATION: Type: CuAl Thickness: 16kÅ 2kÅ PASSIVATION: Type: Nitride over Silox Nitride Thickness: 3.5kÅ 1kÅ Silox Thickness: 12kÅ 2kÅ WORST CASE CURRENT DENSITY: 2 x 5 A/cm 2 at 25mA Metallization Mask Layout HI-200 A 2 A IN IN 1 OUT OUT 1 9 FN3121.9

10 Die Characteristics METALLIZATION: Type: CuAl Thickness: 16kÅ 2kÅ PASSIVATION: Type: Nitride over Silox Nitride Thickness: 3.5kÅ 1kÅ Silox Thickness: 12kÅ 2kÅ WORST CASE CURRENT DENSITY: 2 x 5 A/cm 2 at 25mA Metallization Mask Layout HI-201 A 1 A 2 OUT OUT 2 IN IN IN IN 3 OUT OUT 3 A 4 A 3 All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9001 quality systems. Intersil Corporation s quality certifications can be viewed at Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see FN3121.9

11 Revision History HI-200, HI-201 The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that you have the latest revision. DATE REVISION CHANGE FN Updated Ordering Information Table on page 1. - Added Revision History. - Added About Intersil Verbiage. About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at You may report errors or suggestions for improving this datasheet by visiting Reliability reports are also available from our website at 11 FN3121.9