SYSTEMS FURNITURE SPECIFICATIONS:

Transcription

1 SYSTEMS FURNITURE SPECIFICATIONS: General Infrmatin: Cntracted furniture vendr will be respnsible t field measure the space t verify building dimensins befre the rder is placed. Electrical and cmmunicatins wiring will be cming frm the ceiling, please prvide all necessary cmpnent parts fr this type f installatin. Must prvide 4-circuit pwer within furniture system. Data/Cmm jacks are t be installed abve the wrksurface, please prvide all necessary cmpnents fr this type f installatin. Electrical raceways are t be installed in the base f the panel. Panel System Specificatins: 1.0 Warranty and Testing Lifetime warranty that prduct is free frm defects in materials and wrkmanship. Panels meet r exceed the ANSI/BIFMA X Panel System tests. Panel wiring meets r exceeds UL 183 Manufactured Wiring Systems tests. Panels are designed fr installatin in cmpliance with the Natinal Electric Cde (NFPA 70). Standard panel fabrics meet r exceed UL 723 Surface Burning Characteristic f Building Materials tests. Standard panel fabrics meet r exceed UL 1286 Standard fr Safety f Office Furnishings tests Panels meet the fllwing minimum acustic ratings per ASTM C423-02a and E795-00: Panel with Perfrmance Tackable Acustic Skins NRC:.65, STC: 16 Panel with Tackable Acustic Skins NRC:.55, STC: Envirnmental Requires SCS IndrAdvantage Gld Certified fr indr air quality. Requires nn-dedicated frame t make it easy t disassemble and recycle panel cmpnents Features and Cnstructin: 3 thick nn-dedicated, pen cre steel frame. Allws fr 90 degree and 120 degree planning. Panel frame is cnstructed n-site using vertical junctins and hrizntal frames (rdered separately). Vertical junctins Heights: Please see typical scale drawing: heights may vary up t 1. THE HEIGHT OF EACH PANEL MUST BE STATED ON THE DETAILED PARTS LIST Sltted steel channels in junctin allw fr wrksurface supprts and verhead strage at 1 increments. Lay-in cable ruting is accmmdated in the base area and in the tp cap. Hrizntal cable ruting is als accmmdated with ther penings in the junctins. Leveling glides adjust up t 2. Adjacent panel frames share junctins, thus keeping csts dwn. Panel System Specificatins (cntinued):

2 Hrizntal frame packages Widths: Please see typical scale drawing: width may vary up t 1. THE WIDTH OF EACH PANELS MUST BE STATED ON THE DETAILED PARTS LIST 16 ga. (.059 ) steel rectangular tube cnstructin Quick lck cam assembly (n fasteners). Panel stacking capabilities 12 and 24 lad-bearing stackers. Can wrk n any base panel. With stackers, panel can reach a maximum height f 90. Can stack up t 2 tiers, with the first tier being lad bearing. Requires cable trays t allw fr additinal supprt f cables abve the wrksurface. Requires ff-mdular cnnectrs t allw fin panels t be attached t a spine wall in 1 increments withut defacing the spine wall. Flr anchr brackets allw panel t be secured t the flr t prevent mvement esp. in seismic znes. Trims Skins: Hrizntal trims (tp caps and junctin caps) can be specified as either val r square prfile. Tp caps are steel and attach t the panel with spring steel clips (n tls required). Change-f-Height vertical trims are available in standard 1-1/8 W slim prfile and ptinal cable-ruting 2-1/4 W prfile. Cable-ruting trim allws lay-in cable ruting in change-f-height cnditins. Steel base cvers feature integral hks and install withut tls t the vertical junctins. Base cvers are steel and feature knckuts fr bth pwer and cmmunicatin terminatins. A filler is available fr clsing unused penings. Junctin tp caps are plastic and have either mlded-in alignment features r cme with snap-in aligners t insure prper alignment with adjacent tp caps. Requires: Tackable acustical skins (full-height r segmented) Glass windw segments Offer bth mnlithic and segmented ptins. Are remvable and can be repsitined (nt dedicated t ne psitin). Steel, wd, laminate, tackable and technlgy skins are munted with spring steel attachment clips (n tls needed). Nn-prgressive: any skin in the panel cnfiguratin can be remved withut disrupting any f the ther skins. Allws fr skin segmentatin every 12. Allws fr any cmbinatin f available skin heights and materials. Glass windws are single pane and with safety glass, plastic is nt acceptable. Fabric skins can be field cut fr receptacle/cmmunicatin utlet penings. Tackable acustical skins feature an 8 lb/cu ft. dense fiberglass cre. Skins include a light seal feature t prevent light frm transferring frm ne side f the panel t the ther. Overhead strage can als be up-munted. Pwer and Data Lay-in cable ruting is accmmdated in the base area, the tp f every panel, and thrugh hrizntal and vertical penings. Pwer can be accessed in the base r every 12 vertically. Wiring schematic required:

3 -3+1, 8-wire, 4-circuit Same mdular pwer kit can be in any lcatin n the panel. Requires pen frame cnstructin allws user t lk and stre excess cable in the frame fr additinal future wrkstatins. Pwer is UL rated. Pwer cmpnents are clr-cded and keyed fr safety. Pwer distributin is nt interrupted when stackers are added t the frame. Cables that run thrugh the frame are prtected by the frame s steel cnstructin and d nt interfere with the ability t hang cmpnents. Panel System Specificatins (cntinued): Each side f the panel has access t every circuit distributed within the panel. Pwer and cmmunicatin is field-installed with the ability t add r mve pwer and cable within any panel after installatin. The use f pwer receptacles at any lcatin ther than the base shall nt restrict the number f available receptacles in the panel base. All panels are installed with prvisins in place t prtect the cabling frm system cmpnent damage. If the pwer and cabling is t be placed in frnt f the sltted channel, manufacturer s metal prtectr shields must be supplied and put int place t cver and prtect at least 12 f pwer and cabling passageway. Base pwer-ins accmmdate flr interface. Utility ples accmmdate ceiling interface. Hardwired cnnectin t the building s pwer can be made in the junctin bx included. Pwer and cable ruting/access in base panels is nt disturbed when stacking elements are added including cables at the tp f the base panel. Cable ruting lcatins maintain the minimum bend radius required fr fiber ptic cable. Cabling terminatin desn t utilize any f the pwer access lcatins within the panel base. Can accmmdate a cnslidatin lcatin fr multiple data interfaces. 4.0 Surface Materials Fabric-Cvered Skins Grade 2. Panel trim Grade 2 paint Glass Windw tempered safety glass Strage Cmpnents Specificatins: WARRANTY Lifetime warranty that prduct shall be free frm defects in materials and wrkmanship (includes shipping, parts and labr fr the repair r replacement f defective items). TESTING Must meet r exceed X5.9 Strage Unit Tests MATERIALS CHEMISTRY Shall be cnstructed free f envirnmentally hazardus materials such as PVC, CFC, slvent-based adhesives, heavy metals (chrme, lead and mercury) and benzene.

4 Must be cnstructed free f envirnmentally hazardus prcesses such as thse that prduce VOC s and deplete zne Paint must be VOC-free pwder cat type. Water-based stains and tpcats must be available fr specifying a wd finish. RECYCLED CONTENT AND RECYCLABILITY Fixed mdels (steel drawer uterheads) shall be cnstructed f up t 28% recycled cntent 22% pst cnsumer cntent 6% pre cnsumer cntent. Mbile mdels (steel drawer uterheads) shall be cnstructed f up t 27% recycled cntent 22% pst cnsumer cntent 5% pre cnsumer cntent. Fixed mdels must be up t 100% recyclable at end f life. Mbile mdels must be up t 96% recycled at the end f life. CABINET Exterir dimensins shall be: Depth: 22-5/8 D r 28-5/8 D (add 7/8 fr prud frnt mdels) Widths: 15 W Fixed mdel heights: 27 H Shall have strng 22 ga. (.030 ) steel unibdy cnstructin with welded 20 ga. (.036 ) steel rear hrizntal braces and 16 ga. (.059 ) vertical steel upright braces (2 per side) t minimize racking and misalignment. Back must be finished t allw file t be used in the pen plan withut wrapping with panels. Strage Cmpnents Specificatins Cntinued: Several pre-assembled tps must be available fr mbile mdels: Standard 20 ga. (.036 ) steel tp with 1 H flanged edges, welded in the crners, with a 20 ga. steel reinfrcing channel fr supprt f tp lads. Laminate-cvered 1-1/8 thick particlebard tp with plastic edge banding. Wd veneer-cvered 1-1/8 thick particlebard tp with plastic r wd veneer edge banding. Cushin tp with an ptinal self-string,extendable handle shall be available fr ease f transprt. Base must be 3 H and must be integral t the cabinet. Leveling glides n each crner shall adjust fr uneven flrs with 7/8 range. Factry- r field-installed, frnt-remvable lcks shall simplify field changes. Available keyed randm, cnsecutive, specific r master-keyed. One lck shall lck all drawers. An individual drawer lcking mdel must als be available. Lck mechanism shall engage bth sides f the case t prevent surreptitius entry int the lcked drawers. DRAWERS

5 Interir dimensins: 12 H File Drawers Depth: 18-1/4 H r 24-1/4 H Widths: 12-1/16 W Height: 9-3/8 H 6 H Bx Drawers Depth:, 18-23/32 H r 24-23/32 H Widths: 12-3/4 W Height: 4-7/32 H Drawer frnt must be available in bth painted steel and wd veneer finishes. Steel drawer frnts must be 22 ga. (.030 ) steel and shall feature a flush frnt with fullwidth integral pull r prud frnt with a chice f at least fur applied pulls. Drawer frnts shall be remvable and replaceable in the field. This is less cstly than buying a replacement drawer r new file. Drawer frnts feature a 22 ga. (.030 ) steel innerhead n the inside t prvide a finished appearance and t shield the interir f the drawer frm the lck mechanism. Pulls must be standard cabinet dimensins t allw fr interchangeability with ff-theshelf pulls (aka Custmer s Own Pulls r COP ). Drawer bdy must be 20 ga. (.036 ) frmed steel with a tp hem fr strength and stiffness. Prgressive, heavy-duty steel suspensins shall allw fr cmplete, full depth access t drawer cntents. Drawer suspensins shall feature precisin steel ball bearings fr durable, smth and quiet peratin. Must have rubber bumpers cushin drawer pening and clsing fr quiet peratin. Must have safety interlck t prevent tipping. Only ne drawer can be pened at a time. Each 6 H bx drawer must be prvided with ne remvable divider Strage Cmpnents Specificatins Cntinued: Each 12 H file drawer must be prvided with ne remvable hanging flder bar fr accmmdating side-t-side filing f letter-, A4 internatinal-, and legal-size hanging flders. One remvable pencil tray must be prvided with each bx drawer pedestal. Clear plastic label hlders which fit inside the integral pull r ver the tp edge f prud frnt drawer frnts must be available. OPTIONAL FEATURES User-adjustable rails fr accmmdatin f frnt-t-back filing must be available as a field installed ptin fr drawers.

6 User-adjustable dividers fr accmmdatin f side-t-side filing in 2 increments must be available as a field installed ptin fr drawers. Anchr brackets must be available fr securing the files t the flr fr lcal cde cmpliance. Individual drawer lcks must be available n file/file mdels. These mdels must als feature a security shield abve each drawer t prevent unauthrized access t ther drawers. Extended adjustable leveling glides t replace standard glides must be available fr leveling the unit beynd the 7/8 range fr uneven flr applicatins. A field-installable cnversin kit must be available t prvide fr 28 H freestanding applicatins. Kit must include a tp and cunterweight. The tp prevents unauthrized access t the cntents f the cabinet when the cabinet is nt physically attached beneath a wrksurface. STORAGE TOWERS OVERALL DIMENSIONS 24X24X52-54 MUST BE CLOSEDTOWER WITH SIDE WARDROBE MUST BE AVAILABLE ON LEFT OR RIGHT SIDE OF TOWER MUST HAVE LOCKING DRAWER AND LOCKING COAT LOCKER Wrksurface Specificatins: WARRANTY Lifetime warranty that prduct shall be free frm defects in materials and wrkmanship (includes shipping, parts and labr fr the repair r replacement f defective items). Nte: Cmplete warranty cverage is available nline r upn request. TESTING Desks and Tables must meet r exceed the ANSI/BIFMA X Desk/Table Prduct Tests. Wrksurface edge prfile, n edges designed t cme int cntact with users' wrists, must cmply with ISO (1998) Sectin 5.4.4, ANSI/HFES-100 (2008) sectin , BIFMA G1 (2002) Sectin 9, and CSA-Z412 (2000) sectin Standard high-pressure laminates must meet r exceed NEMA LD High- Pressure Decrative Laminate standards. When applied accrding t published applicatin guidelines, panel-munted r freestanding wrksurfaces must nt sag mre than 1/240 f the ttal wrksurface

7 length when subjected t a lad f 200 punds distrubuted via a rigid 18" x 36" bard lcated flush t the frnt edge f the wrksurface at its apparent weakest pint. When applied accrding t published applicatin guidelines, panel-munted r freestanding wrksurfaces must sustain n structural damage when subjected t the impact f a 225 pund weight bag, 16" in diameter, drpped frm a height f 2" nt the wrksurface, with the edge f the weight bag lcated 1" in frm the frnt edge f the wrksurface at its apparent weakest pint. RECYCLED CONTENT AND RECYCLABILITY Desk supprts shall be made up f at least 30% recycled cntent. Certified tackbard fabrics must cntain up t 100% recycled cntent. Packaging waste must be minimized by palletizing like wrksurfaces. Packaging materials shall cntain 15% t 35% recycled cntent. CERTIFICATIONS Furniture must be certified t meet the emissins requirements f the Califrnia DPH Standard Practice fr the Testing f Vlatile Organic Emissins frm Varius Surces (CA Sectin 01350) and ANSI/BIFMA X7.1 Standard fr Frmaldehyde and TVOC Emissins f Lw-emitting Office Furniture Systems and Seating using either the pen plan r private ffice expsure scenaris defined in ANSI/BIFMA M7.1 Standard Test Methd fr Determining VOC Emissins frm Office Furniture Systems, Cmpnents, and Seating. Testing must be cnducted in accrdance with ANSI/BIFMA M7.1. Certificatin must be prvided by an rganizatin independent f the manufacturer as well as frm the testing labratry, in accrdance with the requirements f ISO/IEC Guide 65 General requirements fr bdies perating prduct certificatin systems. The abve requirement is cvered by SCS IndrAdvantage Gld Certificatin fr indr air quality. Wrksurface Specificatins (Cntinued): GENERAL Desks and tables must be available in a wide range f sizes and shapes, including bth straight and curvilinear shapes, with a variety f strage ptins, table leg and base styles, etc. available. WORKSURFACES Wrksurfaces must be available in nminal 24", 30" depths. Straight wrksurfaces shall be available in 24" t 96" widths. Wrksurfaces fr desks shuld be available in straight, transitin, tapered, crner, extended crner, bullet peninsula, angled peninsula, jetty, bubble jetty, and visitr shapes. Wrksurfaces must be available in "full depth" sizes that allw the rear edge f the wrksurface t be flush with panels in panel-wrapped situatins, s that panel-munted L-crner applicatins can be created withut intrducing nn-unifrm gaps. Wrksurfaces must als be available in sizes that create at least 1/2" gap at the rear edge fr cable management in panel-wrapped applicatins.

8 The same wrksurfaces must be usable in desk applicatins and in panelmunted applicatins. A selectin f crner wrksurfaces must be available with an adjustable keybard shelf. Keybard shelf must have minimum adustment range f 6 abve and 4-1/2 belw the mnitr surface. Keybard shelf mdels shall be available with Single-arm spring mechanism with cntinuus adjustment t prvide superir knee clearance when cmpared t duble-arm mechanisms. Adjustable keybards must have a minimum tilt range f 15 degrees up and 10 degrees dwn. Adjustable keybard shelf shall feature a minimum 1 gap all arund t prevent pinching. Transactin wrksurfaces shall be available fr use as a shelf by wrkstatin standing visitrs. Transactin wrksurfaces shall include attachment brackets fr munting t the tp f a panel. Transactin wrksurfaces shall be available sized t fit n a panel that is munted between tw taller panels. Wrksurface shall be centered n the supprting panel. Must allw munting f utility shelf lights beneath. Wrksurface Specificatins (Cntinued): Standards Included The minimum radius n wrksurface edges designed fr a wrker t rest the fream r wrist must be 3mm. Wrksurfaces must include pilt hles that ensure prper lcatin and secure attachment f desk supprts, strage prducts, panel-munted wrksurface supprts, and legs. Optins Wrksurfaces must include scallps r edge grmmets fr cable management in panel-wrapped r panel-munted applicatins at n additinal charge. Wrksurfaces must als be available with n scallps. Wrksurface wire managers shall be available t cnvert cable scallps t edge grmmets. Grmmets shall als be available fr cable management. Wrksurfaces must be available in either high-pressure laminate r wd veneer. PANEL-MOUNTED WORKSURFACE SUPPORTS

9 Supprts are rdered separately and installed in the field. All supprts must be able t be remved and repsitined later withut any permanent damage t panels r skins. Cantilevers Shall engage vertical panel slts s that the wrksurface can be munted at 1 increments. The same cantilever must be useable n either 18, 24, r 30 nminal depth wrksurfaces, t simplify inventry management and recnfiguratin. The same cantilever must be useable n either the left r right end f a single wrksurface r in a shared applicatin between tw wrksurfaces. Cantilever must be able t switch between these three applicatins withut requiring tls r fasteners except fr thse attaching the cantilever t the wrksurface(s). This feature simplifies inventry management and reduces recnfiguratin csts. Side supprt brackets Shall engage vertical panel slts s that the wrksurface can be munted at 1 increments. Shall be used t supprt the end f a wrksurface that is wrapped by a matching width panel, r in a rear crner f a crner wrksurface. Supprt plate and Tie plates Supprt plates must be available t cnnect tw wrksurfaces and allw ne t supprt the ther. Tie plates must be available t prvide added strength and alignment between tw wrksurfaces. Reinfrcing channel A field installed steel reinfrcing channel shall be available fr heavily laded wrksurfaces r lng spans f unsupprted wrksurface. Center supprt panels and end panels Shall engage vertical panel slts Must be available fr supprting a wrksurface at either standard height (28-1/2 ) r standing height (40-7/8 ) End supprts must be available in nminal 24 and 30 depths. Must be nn-handed. Center supprt panel must be n greater than 11 deep t prvide ample knee clearance. Must have at least ¾ glide adjustment range. Wrksurface Specificatins (Cntinued): LEGS AND TABLE SUPPORTS Pst legs (fr wrksurfaces and tables) Must be available in nminal 26, 28-1/2, and 40-7/8 wrksurface heights. Must be ffered with swivel caster r glide (exceptin: 40-7/8 high is nly available with glide).

10 Must ffer adjustable-height versins which are user-adjustable in n greater than 3/4 increments between 25-1/2 and 31-1/2 wrksurface height. Adjustable-height pst leg with caster shall feature a lcking caster. Must ffer duble pst legs that are visually cmpatible with standard pst legs and are suitable fr a shared applicatin between tw wrksurfaces available in nminal 28-1/2 and 40-7/8 wrksurface heights. All pst legs with glides must have at least ¾ glide adjustment range. C-Legs (fr wrksurfaces and tables) Must be available in nminal 28-1/2 wrksurface height. Must have at least 5/8 glide adjustment range. The same leg must be suitable fr 24 and 30 nminal depth wrksurface applicatins. The same leg must be suitable fr left-hand, right-hand, r shared applicatins (cnnecting tw wrksurfaces). Clumn supprts (fr panel-munted and desk applicatins nly) Must ffer a clumn with extended height adjustment range f at least 3 1/8 (ttal range 28-1/2 t 31-5/8 ). Must als ffer a standard clumn with glide adjustment range f at least 1-1/2. Rund clumns must be at least 4 in diameter t prvide a sturdy-lking supprt fr peninsula wrksurfaces and similar applicatins. Wrksurface Specificatins (Cntinued): DESK SUPPORTS AND MODESTY PANELS Desks shall be n less than 28-1/2" high, in cmpliance with BIFMA G Sectin Supprts must feature adjustable glides fr installatin n uneven flrs. Minimum adjustment range shall be 1 ½. 36"D straight desks must be available with inset supprts, strage and mdesty panels, prviding at least 6" f visitr kneespace alng the entire back edge f the desk. All desks, returns, bridges and ther freestanding wrksurfaces shall prvide an ptin fr munting a mdesty panel with at least 1 1/2" gap between the mdesty panel and the underside f the wrksurface, fr cable management. A cable tray shall be available t manage crds and t blck light frm passing thrugh this gap. All desks, returns, bridges and ther freestanding wrksurfaces must be available with n mdesty panel, t prvide free access t pwer and data utlets in the building wall r panel at any height belw the wrksurface. All desk supprts and strage prducts must pass ANSI/BIFMA X sectin 12, leg strength test, withut mdesty panels present. End supprts Must be available in nminal 24" and 30" depths.

11 Must have at least 1-1/2" glide adjustment range. End supprts shall be L-shaped in plan view, with the back leg f the "L" matching the width f a pedestal, s that the same width mdesty panel can be used in desk shells, single pedestal desks, and duble pedestal desks f equivalent width. End supprts must be nn-handed s the same cmpnents can be assembled int left-hand and right-hand desks and returns. Peninsula supprts Must be available in nminal 24" and 30" widths. Must have at least 1-1/2" glide adjustment range. Peninsula supprts shall prvide fr the attachment f a mdesty panel directly belw the centerline f the wrksurface, spanning the full distance frm the peninsula supprt t the clumn supprt. Crner supprts Crner supprts shall supprt the rear crner f any crner wrksurface. They shall als be usable as intermediate supprts, prviding increased kneespace when crner wrksurfaces are attached t adjacent wrksurfaces. Crner supprts shall include a remvable inner cver fr vertical cable ruting within the supprt. Must have at least 1-1/2" glide adjustment range. Flush Munt brackets Flush munt brackets shall be available t cnnect a return r bridge wrksurface t the frnt edge f anther wrksurface, prviding supprt and alignment. Flush munt brackets shall emply a tw-plate design s the same bracket package can be used fr 24, and 30 nminal depth return and bridge wrksurfaces. Mdesty panels All desks, returns, bridges, and ther freestanding wrksurfaces must be available with either full-height mdesty panels, Half-height mdesty panels must be stackable. Strage units used as freestanding desk supprts Pedestals, lateral files, strage cabinets and bkcases shall be available as a freestanding desk supprt in place f an end panel r ther supprt in mst applicatins t save the extra cst f additinal supprts. Mnitr arms- 360 mnitr rtatin 160 vertical angle range 200 lateral angle range Steel and die-cast aluminum cnstructin fr strength and durability Pneumatic cylinder supprts mnitrs 5 t 20 lbs. Pwder cat finish

12 Pelican Drawer-10 dual purpse drawer, includes file bar Mbile ped: Mbile Bx/File pedestal t fit beneath wrksurface. Tp is steel with a cushin seat tp. Hard casters are frnt lcking. Drawer cnfiguratin will be Bx/File. Must cme with 2 keys. Fabric grade 3