Intruder alarm integration 12V 12-24V. DC Only. Set N.C. N.O. COM N.C. N.O. COM. Alarm 12V. Exit. Contact N.C. COM PSU COM N.C. 1 N.C.

Transcription

1 For DC S Se Se Server Conneced Server Conneced 0 Server Link 00 0/00 Eherne hp://paxon.info/07 LABEL 3456 HERE Server Link 00 ns End of Line Terminaion RS485 Nework CAT5 Cable Coding or or Tx R elay xi -4V. Tamper For DC S Se Se Server Conneced Server Conneced 0 Server Link 00 Server Link 00 0/00 Eherne hp://paxon.info/07 LABEL 3456 HERE ns End of Line Terminaion RS485 Nework CAT5 Cable Coding or or Tx R elay xi -4V. Tamper 05/3/04 Ins US Ne plus conrol uni - UL Paxon Technical Suppor supporus@paxon-access.com Technical help is available: Monday - Friday from 0:00 AM - 8:00 PM (EST) Documenaion on all Paxon producs can be found on our web sie - hp:// For insrucions in alernaive languages - hp://paxon.info/000 Wiring The Ne plus ACU has reader pors and 3 oupu relays, bu can conrol jus one door. The configuraion of one conrol uni per door grealy simplifies insallaion and is ulimaely highly cos effecive. Inruder alarm inegraion DC power supply /keypad Media Deec Media Deec 0 Ne plus /00 Eherne indicaions DC DC (opional) C auion: y readers Sense Screen spare from daa Screen spare from daa Wh/Grn Wh/Grn /keypad Wh/Orng O u r Powe pus Ou pus Wh/Orng Power DC Only Relay E C onac Buo n P SU/Tamper N.O SENSE I ARM OK TX Ne plus RS485 CAT5 RX EXIT - 4V N.O N.O EXIT Swichable 0 ohm from previous ACU resisors TCP/IP pach lead C auion: For DC readers y Se Se Server Conneced 0 Server Link 00 0/00 Eherne Sense End of Line Terminaion Screen or spare from daa Inruder RS485 Nework CAT5 Cable Coding Tx Wh/Grn Ne plus hp://paxon.info/ Server Conneced LABEL 3456 HERE Server Link 00 S ns Screen or spare from daa Wh/Grn Wh/Orng Wh/Orng O u pus r Powe Ou pus Power DC Only Relay P SU/Tamper C onac E xi Buo n R elay -4V. Tamper Media Deec Media Deec DC DC N.O Tamper swich (opional) 0 00 SENSE ARM OK TX Ne plus RS485 CAT5 RX o nex ACU For a fail open lock (Maglock), wire o he "" erminal insead of "" 0/00 Eherne I - 4V N.O Normally N.O closed door conac EXIT EXIT 3456 C auion: y readers Door Lock buon (push o make) (opional) Sense Ne plus Screen spare from daa Screen spare from daa Wh/Grn Wh/Grn Wh/Orng O u pus r Powe Ou pus Wh/Orng Power DC Only Relay C onac E Buo n P SU/Tamper /4V () - Power. Relay () - The relay is energised - (NO/ conacs are closed). Relay () - The relay is energised - (NO/ conacs are closed). (Red) - oupu is acive. () - The exi buon conacs are closed. () - The door conacs are closed. Tamper () - The amper conacs are closed. () - The conacs are closed. OK ( flash) - The inernal sofware is running. Terminaion (Red) - The on-board resisors are in place across he RS485 daa pairs. (Red) - The ACU is receiving daa (TCP/IP or RS485) - See also FAQ secion. Tx () - The ACU is responding o daa - (TCP/IP or RS485). Server Conneced () - The TCP/IP inerface is communicaing wih he PC Ne server. Server Link - = 00 Mbi/s : = 0 Mbi/s (TCP/IP speed). PAGE

2 ense End o Line erminaion R Ne ork CA Cable Codin x 0/00 E erne er er Conneced 0 er er Link 00 e Ne plus LACE ERIAL N M ER LA EL ERE Ou o er Relay R elay xi uo amper ense End o Line erminaion R Ne ork CA Cable Codin x 0/00 E erne er er Conneced 0 er er Link 00 e Ne plus LACE ERIAL N M ER LA EL ERE Ou o er Relay R elay xi uo amper ense End o Line erminaion R Ne ork CA Cable Codin x 0/00 E erne er er Conneced 0 er er Link 00 e Ne plus LACE ERIAL N M ER LA EL ERE Ou o er Relay R elay xi uo amper ense End o Line erminaion R Ne ork CA Cable Codin x 0/00 E erne er er Conneced 0 er er Link 00 e Ne plus LACE ERIAL N M ER LA EL ERE Ou o er Relay R elay xi uo amper ense er er Conneced 0 er er Link 00 e Ne plus LACE ERIAL N M ER LA EL ERE End o Line erminaion R Ne ork CA Cable Codin x 0/00 E erne Ou o er Relay R elay xi uo amper Red v dc Keypad Brown Yellow Blue Mauve Black/Whie Brown Yellow Screen or spare from nework Whie/ 3 Whie/ 4 +v 0v Com Com Oupu 0v 0v 0v Tamper Overview A Ne plus can connec o he Ne PC using eiher an un-shielded RJ45 pach or an RS485 daa line. This grealy increases he number of insallaion opions available o he insaller. One Ne plus can also be used as he TCP/IP inerface for an RS485 daisy chain of Ne plus and Ne classic unis. When used wih a TCP/IP connecion, i mus firs be deeced using he Ne Server Configuraion Uiliy as defined laer in his insrucion. When used wih an RS485 daa line, on-board erminaion resisors can be pu in circui wih a simple slide swich. Ensure ha unis insalled in he middle of he daa line have his swich urned. A dedicaed connecion is provided. Sie Layou Examples Ne plus Ne plus Ne plus Ne plus Ne plus Ne classic C auion: For DC readers y /Grn creen r om daa or spare pus Oran e /Orn C onac E n / amper C auion: For DC readers y /Grn creen r om daa or spare pus Oran e /Orn C onac E n / amper C auion: For DC readers y /Grn creen r om daa or spare pus Oran e /Orn C onac E n / amper C auion: For DC readers y /Grn creen r om daa or spare pus Oran e /Orn C onac E n / amper C auion: For DC readers y /Grn creen r om daa or spare pus Oran e /Orn C onac E n / amper Red Brown Yellow Blue Mauve Black/Whie Brown Yellow Keypad CAUTI: for v d.c. readers y. For correc connecion of old 5v readers, refer o insrucions. Nework CAT5 coding Serial number Tes ID: z-440 Power Relay Relay Inpus v 5v OK Tamper Relay Relay Tx RS485 daaline TCP/IP LAN TCP/IP LAN TCP/IP LAN TCP/IP LAN Here are wo ypical sie layous. - The Ne plus ACU's can be individually conneced o he Ne PC via he sie LAN nework. - The Ne plus ACU can be used as he TCP/IP converer for a line of Ne plus and Ne classic ACU's. The TCP/IP inerface allows an RS485 daa line o be conrolled by he Ne Server running across a LAN nework. An RS485 daa line has a 000 yds maximum. This disance can be increased wih he use of Paxon high speed repeaers or by using shorer independan daa lines using muliple LAN connecions conrolled from he same PC. The ACU shall be insalled wihin he proeced premises as boh he power and lock wiring is presen a he PCB. A Tamper alarm inpu is provided on he PCB - See Inpu/Oupu Wiring The ACU's will coninue o operae in a 'sandalone' mode if he PC is shu down or he daaline is disconneced. Any Evens ha occur during his period are sored in he ACU and he PC is updaed when i comes back on line. The PC mus be running for any 'server based' funcions o operae. (Anipassback, Time and Aendance, ec). TCP/IP and RS485 indicaion The Ne plus performs wo funcions. I is an access conrol uni and also a TCP/IP RS485 converer. Informaion can pass across he PCB beween he TCP/IP and RS485 daa por bu is no relevan o his ACU - Server Conneced (Seady ) This shows ha he TCP/IP inerface is acive and receiving daa from he Ne PC server. This includes all daa for oher ACU's ha may be linked via he RS485 daa por. - and Tx 's These 's show he aciviy for his ACU y. This is same indicaion as seen on a Ne classic ACU. I is no dependan on he source (TCP/IP or RS485). The will flash for all daa being received and he Tx will y flash when his uni responds o is own address. PAGE

3 Cable ype Cable specificaion Use Max lengh Type RS485 Daa Line 000 yds x wised pairs - Belden 873 or Ca5 equivalen / Keypad 500 fee 8 core, shielded - Beldon 9538, Alpha 98C (AWG) or equivalen Inpu / Oupu 00 yds conducor - Alpha 7C (AWG) or equivalen Mouning Pars ki Par Number Qy Fiing Ki fk-08 Ferrie ube The ACU is suppored on mouning poss locaed a he corners. Gromme, mm hole 3 Wall plugs 3 Pozi round woodscrew - zinc Pozi panhead lid screw Rubber washer Cable gland Cable gland lock nu 4 Cable clip 0 Cable ie N400 diode Fiing Ki fk ohm Resisor /4W Cable ie Descripion If he uni is supplied in a plasic housing, i should be fixed o he surface wih suiable faseners. Four screws and wall plugs are provided for his in he pars ki along wih ies and wo smaller screws for he lid. Moun he four corner f/f mouning poss o he plae wih four of he machine screws and hen secure he circui board o heir ops using he remaining four screws. Conrol uni insallaion The ACU shall be insalled wihin he proeced premises as boh he power and lock wiring is presen a he PCB. A Tamper alarm inpu is provided on he PCB - See Inpu/Oupu Wiring Where he ACU is being insalled wihin a plasic enclosure, he hub mus be conneced o he condui before i is conneced o he plasic enclose. This is o eliminae he poenial of any excessive orque loading being applied o he plasic enclosure during insallaion. This housing should be fixed o he surface wih suiable faseners; screws and wall plugs are provided for his in he fiing ki. Also provided are ies o secure he cabling and a smaller securing screw for he lid. Wire he componens o he Access Conrol Uni (ACU) as shown on he firs page. This uni is for Indoor use y Press he exi buon or in he absence of an exi buon, shor he and exi erminals ogeher. The configured lock oupu will come on and he lock should release. The uni will coninue o operae in a 'sandalone' mode if he PC is shu down. Any Evens ha occur during his period are sored in he uni and he PC is updaed when i comes back on line. PC insallaion The curren specificaion for compaible PC hardware, nework and operaing sysems is available on our websie a he following link: hp://paxon.info/70 PAGE 3

4 Connecing o he PC via he Eherne por If he TCP/IP daa connecion is longer han 5 f he following surge proecion device mus be insalled wihin 3 f of he conrol uni. Daa line surge proecor. Emerson Nework Power: Model LCDP-060. The IP address should be assigned a fixed value, or a DHCP reservaion. Unreserved IP addresses issued by DHCP servers are no guaraneed o be consan, leading o poenial failure of PC o Ne bridge communicaions. Run he Ne Server Configuraion Uiliy (Sar/Programs/Ne) and Click on TCP/IP nodes. Click on;deec and he MAC address of he device(s) will appear in he able. You mus hen use he "IP address configuraion" ab o manually assign he IP address, subne mask and gaeway. Be aware ha if he IP address ha you give he device is no in he same IP range as he PC, he device will no longer respond unil you connec o i wih a PC ha is in he same IP range. Some firewall/virus proecion sofware and oher wireless hardware can block he IP deecion process. Disable hese and ry o deec he device again. Please conac Technical Suppor if you require furher advice. If you deec he MAC address bu he device now shows 'No Responding', you mus check he IP address, o make sure i is sill in range wih he PC or nework. If i is no, you should eiher change he IP address of he PC or he IP address of he device so hey are boh again in he same range. Our Technical eam can alk you hrough his if you need help. If he MAC address does no appear when you click;deec, ensure ha he following pors are open on all devices beween his uni and he Ne PC:- 69 UDP 000 TCP 3078 UDP TCP/IP Rese - The uni can be reurned o DHCP seings by powering down he uni and linking he '' and '' erminals on reader por. Power up he uni again and he uni will beep o acknowledge he link. You may now remove he link and he OK will flash fas for a few seconds. When he OK reurns o a seady hearbea, he IP seings will be rese o DHCP. If you sill canno deec he MAC address of he device, call our Technical Suppor Help line. NOTE: The device will 'beep' when deeced by he Ne Server Configuraion Uiliy or when new IP seings are applied. The sounder will also respond o a direc 'Ping' over he nework o help locae he uni. When connecing o a WAN or differen subne mask If you are connecing his device o a remoe subne which is differen from he Ne sofware PC, he sandard deec mechanism canno work across he nework rouers beween hem. The IP address, along wih he correc subne mask and gaeway for he remoe subne have o be se. Eiher do his on he local subne wih he exising Ne PC, or use a PC on he remoe subne once he device is insalled. The PC ha has he Ne server insalled mus be able o access he IP address range on he WAN/remoe sie. PAGE 4

5 This may require he rouers and gaeways o be configured beween he neworks. Again, his would be done by he Nework adminisraor of ha sie. Make sure he pors lised above are open on all inermediae rouers. Once insalled, creae a record wih he;add buon (if none was creaed during iniial se up) and you should hen be able o deec is MAC by enering he IP address in he Configuraion screen Ping box. Naming TCP/IP Eherne inerfaces The rename buon can be used o give an inerface a meaningful name in he sysem. This can be especially useful when more han one inerface is used, as he name will appear in he doors screen wihin Ne showing which ACUs are conneced o which daaline, helping in any fuure faul finding process. TCP/IP Loopback es The following es should be run if here are problems seing up he IP configuraion of he inerface. This es sends daa o he device and checks his agains he daa i receives back. This confirms ha he nework pahing is working correcly. The Ne server program mus be shu down during his es. Remove any wires from he RS485 daa line connecor and creae a hardwired daa loop as follows. Connec he o Whie/ and o Whie/. To run he es, click he Loopback buon in he advanced secion of he Server Config Uiliy/TCP/IP Nodes. If he es fails, connec he uni direcly o he PC wih a nework pach and es i again. Should his sill fail, please call Technical Suppor for furher advice. Connecing o he PC or oher ACU's via he RS485 daa connecion 90% of insallaion fauls are caused by wiring errors on he RS485 daa line. Special aenion o his area can save ime and effor. END OF LINE TERMINATI - 0 ohm resisors mus be linked across each daa pair a he beginning AND end of he line. This can be done on many unis wih a swich or jumpers. If no, resisors are provided wih he converer. & Daa Cable Screens - Daa screens and spare MUST be conneced hroughou. - and keypad screens where provided, should be conneced o he Black erminal. The daa line mus be wired in a single daisy chain. The daa connecion o he PC may be locaed a any posiion along he daa line. Ne Server Conrol uni RS485 daa line resisance check Power down all TCP/IP, USB and RS3 converers (individual and Ne plus). Check he resisance across each daa pair is ohms. Check ha here are no daa line o screen shors. Check he screen of he daa is coninuous - his provides he DC sysem reference. PAGE 5

6 Insallaion and es Wire he componens o he Access Conrol Uni (ACU) as shown on he firs page. Press he exi buon or in he absence of an exi buon shor he and exi erminals o es he relay funcion. The lock Relay will come on and he lock should release. Each ime he uni is powered on, i will run an inernal healh check. During his phase (abou 5 secs) he OK will flash quickly before changing o a slower hearbea. The reader's defaul indicaion has all he 's on. Access graned is denoed wih a single flashing. Access Denied is a single flashing. Ensure ha all he 's are li on he reader/keypad. Tes each reader by presening a oken and he uni should beep and display a single flashing red or green. Mainenance The Ne ACU is designed o ake inpu from Clock and Daa readers hrough is wo (In/Ou) reader pors. I can also be configured for Wiegand (6 / 50 bis). I has an RS485 communicaions por ha is used for uploading firmware and user informaion as well as providing Even informaion o he PC. Following he compleed insallaion of his equipmen, no furher mainenance or esing is required. I is advisable o ensure ha any hird pary backup power supplies or recovery procedures are checked regularly o ensure ha he operaion of he Paxon sysem is no compromised. - Shor circuiing, muilaion or incineraion of he cells mus be avoided o preven one or more of he following occurrences; Release of oxic maerials, release of hydrogen and/or oxygen gas, rise in surface emperaure. - If a cell has leaked or vened he conrol uni mus be replaced. The baery is no o be replaced. Sysem checks Presen a oken a each reader. An even for each read should appear in he Evens screen. Change he defaul password for he Sysem Engineer. Se up oher operaors if required. Se up ime zones. Se up access levels. Users can be added & assigned o he required access level. Deparmens can be creaed if required. The Ne CD can assis here wih deailed applicaion noes for seing up users and general sysem operaion. PAGE 6

7 INPUT / OUTPUT WIRING buon Where fied, a 'push o make' buon is required. (See Specificaion able for raings) The will be when he swich is closed. - Buon Pushed. When he erminal is shored o, he will illuminae and he ACU will operae Relay. The reader/exi buon will flash during his period. More han one exi buon can be wired in parallel. Relay will remain ransfered while he shor o remains. Door A NO swich may be fied so ha i is held closed while he door is shu. The will be when he swich is closed. - Door Closed. When conneced, Ne will check he door posiion during access aciviy and will raise an in he even of a 'Door Forced' or 'Door lef open' condiion. Tamper swich The ACU supplied in a plasic housing has a 'NO' amper swich fied and pre-wired ino he circui board. The Tamper will be when he swich is closed. Ne will monior he swich posiion and will raise an in he even of a 'Tamper' condiion. Connec o a UL lised burglar alarm uni for supervision. monioring The will be when he NO Relay conacs are closed. - Power OK. The Ne sofware will monior he relay conacs and will raise an in he even of a 'Power Fail' condiion. Door Bell - Relay Pressing he bell buon on he keypad will resul in Relay being energized for second. A bell sounder can be conrolled by wiring one of he bell feeds across / NO on he relay. See Specificaion able for Oupu Raings PAGE 7

8 sounder This local alarm has a ransisor 'open drain' oupu, (no a dry conac relay) and will swich A a DC for a bell, ligh ec. This local oupu can be urned on or off for each ype of alarm and can be configured o sound coninuously or inermienly o disinguish beween differen alarm ypes. Lock Wiring - Relay oupu DC power supply Lock power supply Door lock Fail closed Fail open Lock wih an independen supply This is a E door conroller using a dry conac relay. The lock is wired across and. A link ( o NO or NC) is required, depending on lock ype (Fail Closed / Open). Fi he supplied diode across and (Silver end o ) o proec he relay conacs. The dry relay conacs can be used o swich he power from an independen lock power supply. Wire he o NC or NO and he lock o ; he +VCC supply is wired direcly o he lock. Panic hardware A break glass should be fied, in conjuncion wih a fail open release o ensure a reliable egress mehod in he even of an emergency. This is fied on he supply wire o he lock and drops he power ensuring ha he lock opens. Break Glass fied The diagram shows how o include he break glass in he Ne lock wiring circui. Fire Door Inerface A fire alarm sysem mus be used o release all fire doors. Exernal relay conacs are held closed by he fire alarm's inerface and will be dropped during an alarm condiion. The sysem is fail safe as he door will release even if he burns hrough. Exernal Fire Door relay fied PAGE 8

9 Sofware configuraion Door name: Name he Door. Door open ime: Se he door open ime. Unlock he Door during: Holds he door unlocked during his imezone. - Se o 'A No Time' for normal user operaion. : Seings for and Keypad on he ACU. : Seings for and Keypad on he ACU. : Conains seings for he differen ypes of alarm. Codes: Valid codes can be viewed, added and removed. (Can y be viewed when a keypad is acive). Evens: Shows he evens for he conrol uni seleced. Name: Each reader can be named individually if required. ype: Se he reader ype, if appli. Keypad ype: Se he keypad ype, if appli. Token daa forma: Selec he ype of cards being used on he sysem. (New formas can be creaed). operaing mode: Se he operaing mode. Timed operaing modes: A differen operaing mode can be configured wihin a ime window. acion: Se he acion required when access is graned. UL compaable readers Par Type Par Type 37-0-US TOUCHLOCK K75 keypad US PROXIMITY P75 reader 37-0-US TOUCHLOCK K75 keypad, screw connecor US PROXIMITY P75 reader, screw connecor 37-0-US TOUCHLOCK K75 sainless seel keypad US PROXIMITY P50 reader 37-0-US TOUCHLOCK K75 sainless seel, screw connecor US PROXIMITY meal reader US PROXIMITY KP75 keypad US PROXIMITY meal reader, chrome US PROXIMITY KP75 keypad, screw connecor US PROXIMITY meal reader, brass US PROXIMITY panel moun reader Inruder alarm inegraion A dedicaed por for inpu and oupu signals is provided when inegraing a Ne plus ACU wih an alarm sysem. Please see AN035 - Inegraing Ne wih an inruder alarm sysem < hp://paxon.info/9 > or call Technical Suppor for furher informaion. - confirmaion Push Buon - Wire across and. Sense - Wire a volage free loop across and Sense o monior he alarms curren saus. Se - Wire a volage free loop across and or o provide a se signal for he alarm. PAGE 9

10 Technical Help - RS485 Daa line resisance check - ACU no responding or fails o be deeced. QFirs power down any daa line converers and disconnec any ACU's ha do no have a flashing OK. Using a QMulimeer, measure he resisance across he Whie/ and pair a one end of he nework. QA resisance of beween 60 and 80 ohms is required. Repea he es for he Whie/ and pair. QThis is vial for a sable and rouble free insallaion. - ACU Rese - No OK flashing. QThe ACU has no facory rese condiion as i does no conain any fixed seings. The uni does have an operaing Qprogram (firmware) ha conrols is funcions and can be confirmed as running by means of he flashing OK. Q- If he OK is flashing seadily, hen here should be no reason o rese he uni. Q- If he OK is no flashing, you need o clear he uni so ha i can receive a firmware download from he PC. Q Any oher ACU's wihou OK 's mus be aken off he line or powered down. Q. Sop Ne Server (Ne server icon - Boom righ of screen - Righ mouse click, Selec Sop he Ne Server). Q. Power down he Ne ACU. Q3. Inser a link wire beween he '' and '' erminals on reader por. Q4. Power up he ACU. - The OK flashes very quickly. Q5. Wih he uni sill powered, remove he link. Q6. Go o he PC and Sar he Ne Server and go ino he Doors screen. Click on he Deec buon. This Q should look for he ACU and hen download is firmware (This may ake up o 5 minues). - The OK Q should now be flashing wih a seady hearbea. This procedure mus y be done for one ACU a a ime. Q NOTE: If his uni is using he TCP/IP inerface, any fixed IP seings will be reained. Q If he uni is in DHCP mode i will need o be deeced a each sage using he Server Config Uiliy as a new Q address may be issued by he IP server, each ime he PCB reses. 3 - Can we use a DHCP IP address? QThe Eherne inerface does suppor DHCP, bu for more reliable communicaion, a saic IP address mus be Qreserved for he uni. This is because some servers issue differen DHCP addresses each ime hey are resared Qand his requires he Ne inerface o be manually se up again - a ime consuming process. 4 - TCP/IP - Direc PC connecion. QConnec he nework inerface direcly o he LAN por of he PC. Wihou he presence of a DHCP server he uni Qwill defaul o an IP address in he range X.X. QCheck he IP address of he nework card of your PC by yping IPCFIG a he command promp. Deec he QTCP/IP inerface hrough he Ne Configuraion Uiliy and change he IP address of he inerface o an address Qsimilar o ha of your machine. For example, if he IP address of he PC is , change he IP address Qof he TCP/IP inerface o Once he IP address of he inerface has been changed ino he range of Qhe PC hen Ne will be able o communicae wih i. QNOTE: Do no change he IP address of your PC o x.x, his will no allow he IP address of he TCP/IP Qinerface o be fixed correcly. 5 - Canno deec ACU via a TCP/IP inerface. Q. Ensure he TCP/IP inerface has been deeced in he Ne Configuraion Uiliy, and responds when PINGed Q from he uiliy. A saic IP address mus be used for he inerface. Q. If he inerface is responding, ry a loopback es. (see Loopback secion) Q3. The Ne daa line should be checked for resisance readings. 6 - s/keypads no working. Q- Sofware seings - Confirm ha he seings of he reader or keypad are correc. Q- Connecions - Check he wiring and inegriy of he connecors. - If possible, es his reader on he oher por. Q- Cable - Belden 9540 or 9538 should be used o exend he reader. Twised pair alarm Q should no be used. To confirm ha a exension is no a faul, wire he reader direc ino he reader por. Q- Supply volage - Confirm ha he volage is wihin specificaion. (see able) Q- User oken - Confirm ha he user oken used for esing is OK by presening i o a known working reader. Q- Inerference - Confirm wheher he reader works when esed 'in hand' and no mouned on he wall. Ensure Q ha readers are no mouned back o back or here is no inerference from oher local RF devices. PAGE 0

11 Produc compliance and limiaions To comply as a UL lised insallaion, he following condiions mus apply:- The power mus be provided via a separae DC supply, a UL Lised Access Conrol (or Burglar ) Class, Power-Limied, power source capable of 4 hours sandby mus be employed. This is wired ino he and /4V erminals and he secured wih he ies provided. Wiring mehods shall be in accordance wih he Naional Elecrical Code (ANSI/NFPA70), local codes, and he auhoriies having jurisdicion. Sofware feaures and funcions have no been evaluaed by UL. Server based funcions (Anipassback, Time and Aendance, ec) have no been evaluaed by UL and canno be used for UL 94 insallaions. The use of Wiegand readers and he configuraion sofware has no been evaluaed by 'UL' Wiring: - Where an equivalen / wire is used i mus be ' UL Lised ' All inerconnecing devices mus be UL Lised. buons - A UL lised 'push o make' buon mus be used. Door conac - A UL lised 'Normaly Open' () swich mus be used. Tamper alarm - Connec o a UL lised burglar alarm uni for supervision. sounder - Connecions o his alarm oupu have no been evaluaed by UL for burglar alarm use. Break glass- A UL lised break glass mus be used. Fire door inerface - This feaure has no been evaluaed by 'UL' and mus no be used in UL-94 insallaions. Inruder alarm inegraion - This feaure has no been evaluaed by 'UL' and mus no be used in UL-94 insallaions. For CAN/ULC-S39 insallaions, erminals, leads and wiring mehods mus comply wih CSA, C., Canadian elecrical code, Par, safey sandards for elecrical insallaions. The use of any add-on, expansion, memory or oher module manufacured or supplied by he manufacurer's represenaive will invalidae he CAN/ULC-S39 cerificaion. This device complies wih Indusry Canada licence-exemp RSS sandard(s). Operaion is subjec o he following wo condiions: () his device may no cause inerference, and () his device mus accep any inerference, including inerference ha may cause undesired operaion of he device. FCC Compliance Class B digial devices. This equipmen has been esed and found o comply wih he limis for a Class B digial device, pursuan o Par 5 of he FCC Rules. These limis are designed o provide reasonable proecion agains harmful inerference in a residenial insallaion. This equipmen generaes, uses and can radiae radio frequency energy and, if no insalled and used in accordance wih he insrucions, may cause harmful inerference o radio communicaions. However, here is no guaranee ha inerference will no occur in a paricular insallaion. If his equipmen does cause harmful inerference o radio or elevision recepion, which can be deermined by urning he equipmen off and on, he user is encouraged o ry o correc he inerference by one or more of he following measures: -- Reorien or relocae he receiving anenna. -- Increase he separaion beween he equipmen and receiver. -- Connec he equipmen ino an oule on a circui differen from ha o which he receiver is conneced. -- Consul he dealer or an experienced radio/tv echnician for help. PAGE

12 Opions Sales Code US US Descripion Ne plus access conrol uni Ne plus ACU in plasic housing Specificaions Elecrical Volage PCB Curren (depending on aciviy) Relay swichable volage Relay swichable curren oupu volage oupu curren Combined reader por oupu curren por volage buon volage buon curren Environmen Operaing emperaure - Baery limis Humidiy Waerproof Communicaion Eherne nework speed Eherne bandwidh requiremen DHCP suppor (fixed IP recommended) RS485 nework speed Feaures Number of Cards Number of PIN's Access Levels Time Zones Maximum door open ime Number of Codes Doors per ACU pors per ACU s per por Keypads per por ACU per daaline Daalines per PC Daa reenion afer oal power loss Evens sored in ACU wih no server connecion Dimensions Conrol Uni Min Max DC 4V DC (+0%) 00 ma 3 A 4V DC (+0%) 4 A DC A 500 ma.4v DC DC.8V DC DC 0 ma Min Max 0 C (3 F) 55 C (3 F) 85% - Relaive humidiy No Min Max 0 Mbis/sec 00 Mbis/sec 00 kbis/sec Yes 5. kbis/sec Min Max 50,000 Ne v4.6 50,000 Ne v sec 999,999 sec Ne v4. 30 days,78 Widh Heigh Deph 4 / inch 5 inch inch This produc is no suiable for reail sale. All warranies are invalid if his produc is no insalled by a rained echnician. PAGE