Precision Monolithic Quad SPST CMOS Analog Switches

Transcription

1 G4HS, G42HS, G43HS Precision Monolithic Quad SPST MOS Analog Switches ESRIPTION The G4HS series of monolithic quad analog switches was designed to provide high speed, low error switching of precision analog signals. ombining low power (0.3 µw) with high speed (t ON : 68 ns), the G4HS family is ideally suited for portable and battery powered industrial and military applications. To achieve high-voltage ratings and superior switching performance, the G4HS series was built on Vishay Siliconix s high voltage silicon gate process. An epitaxial layer prevents latchup. Each switch conducts equally well in both directions when on, and blocks input voltages up to the supply levels when off. The G4HS and G42HS respond to opposite control logic as shown in the Truth Table. The G43HS has two normally open and two normally closed switches. FEATURES 44 V supply max. rating ± V analog signal range On-resistance - R S(on) : 2 Fast switching - t ON : 68 ns Ultra low power - P : 0.3 µw TTL, MOS compatible Single supply capability BENEFITS Widest dynamic range Low signal rrrors and distortion Break-before-make switching action Simple interfacing APPLIATIONS Precision automatic test equipment Precision data acquisition ommunication systems Battery powered systems omputer peripherals Available Available FUNTIONAL BLOK IAGRAM AN PIN ONFIGURATION G4HS ual-in-line and SOI G4HS QFN6 G4HS L IN S GN S IN 2 2 S 2 S 3 3 S GN S IN IN S 2 S 3 IN N IN 2 2 Key S 4 8 S 2 7 N 6 6 N GN 7 S S 3 IN IN Top View 4 IN 4 Top View IN IN 4 N IN 3 3 Top View TRUTH TABLE Logic G4HS G42HS 0 ON OFF OFF ON * Pb containing terminations are not RoHS compliant, exemptions may apply ocument Number: 7203 S3-283-Rev., 27-May-3 THE PROUTS ESRIBE HEREIN AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9000

2 G4HS, G42HS, G43HS FUNTIONAL BLOK IAGRAM AN PIN ONFIGURATION G43HS ual-in-line and SOI G43HS QFN6 G43HS L IN 6 IN S 3 4 S GN 2 S 4 6 S IN IN 3 Top View S GN S IN IN IN 4 IN 3 3 Top View S 2 S 3 IN N IN 2 2 Key S 4 8 S 2 7 N 6 6 N GN 7 S S IN 4 N IN 3 3 Top View TRUTH TABLE Logic SW, SW 4 SW 2, SW 3 0 OFF ON ON OFF ORERING INFORMATION Temp. Range Package Part Number G4HS, G42HS G43HS - 40 to 8-40 to 8 6-Pin Plastic IP 6-Pin Narrow SOI 6-Pin QFN 4 x 4 mm (Variation ) 6-Pin Plastic IP 6-Pin Narrow SOI 6-Pin QFN 4 x 4 mm (Variation ) G4HSJ G4HSJ-E3 G42HSJ G42HSJ-E3 G4HSY G4HSY-E3 G4HSY-T G4HSY-T-E3 G42HSY G42HSY-E3 G42HSY-T G42HSY-T-E3 G4HSN-T-E4 G42HSN-T-E4 G43HSJ G43HSJ-E3 G43HSY G43HSY-E3 G43HSY-T G43HSY-T-E3 G43HSN-T-E4 2 ocument Number: 7203 S3-283-Rev., 27-May-3 THE PROUTS ESRIBE HEREIN AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9000

3 G4HS, G42HS, G43HS ABSOLUTE MAXIMUM RATINGS Parameter Limit Unit to 44 GN to 2 (GN - 0.3) to () igital Inputs a, V S, V () - 2 to () + 2 or 30 ma, whichever occurs first ontinuous urrent (Any terminal) 30 Peak urrent, S or (Pulsed ms, 0 % duty cycle) 00 Storage Temperature Power issipation (Package) b (AK, AZ Suffix) - 6 to 0 (J, Y, N Suffix) - 6 to 2 6-Pin Plastic IP c Pin Narrow SOI d Pin erip e 900 L-20 e Pin (4 x 4 mm) QFN f 880 Notes: a. Signals on S X, X, or IN X exceeding or will be clamped by internal diodes. Limit forward diode current to maximum current ratings. b. All leads welded or soldered to P board. c. erate 6 mw/ above 2. d. erate 7.6 mw/ above 7. e. erate 2 mw/ above 7. f. erate 23. mw/ above 70. V ma mw SPEIFIATIONS a Parameter Symbol Test onditions Unless Specified = V, = - V = V, V IN = 2.4 V, 0.8 V f Temp. b Typ. c A Suffix - to 2 Suffix - 40 to 8 Min. d Max. d Min. d Max. d Analog Switch Analog Signal Range e V ANALOG - - V rain-source On-Resistance Switch Off Leakage urrent hannel On Leakage urrent igital ontrol R S(on) I S(off) I (off) I (on) = 3. V, = - 3. V I S = - 0 ma, V = ± 8. V = 6. V, = - 6. V V = ±. ma, V S = ±. V = 6. V, = - 6. V V = V S = ±. V ± ± ± Input urrent, V IN Low I IL V IN under test = 0.8 V Input urrent, V IN High I IH V IN under test = 2.4 V µa Input apacitance e IN f = MHz pf ynamic haracteristics Turn-On Time t ON R L = 300, L = 3 pf 27 6 Turn-Off Time t OFF V S = ± 0 V, see figure ns Break-Before-Make Time elay t G43HS only, V S = 0 V R L = 300, L = 3 pf 20 harge Injection e Q V g = 0 V, R g = 0, L = 0 nf 22 p Unit na ocument Number: 7203 S3-283-Rev., 27-May-3 3 THE PROUTS ESRIBE HEREIN AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9000

4 G4HS, G42HS, G43HS SPEIFIATIONS a Parameter Symbol Test onditions Unless Specified = V, = - V = V, V IN = 2.4 V, 0.8 V f Temp. b Typ. c ynamic haracteristics (ont d) Off Isolation e hannel-to-hannel rosstalk e OIRR X TALK R L = 0, L = pf f = MHz Source Off apacitance e S(off) 2 rain Off apacitance e (off) f = MHz 2 hannel On apacitance e (on) 30 Power Supplies Positive Supply urrent I+ Negative Supply urrent Logic Supply urrent I- I L = 6. V, = - 6. V V IN = 0 or V Ground urrent I GN A Suffix - to 2 Suffix - 40 to 8 Min. d Max. d Min. d Max. d Unit db pf µa SPEIFIATIONS a (for Unipolar Supplies) Parameter Symbol Test onditions Unless Specified = 2 V, = 0 V = V, V IN = 2.4 V, 0.8 V f Temp. b Typ. c A Suffix - to 2 Suffix - 40 to 8 Min. d Max. d Min. d Max. d Analog Switch Analog Signal Range e V ANALOG 2 2 V rain-source On-Resistance R S(on) = 0.8 V, I S = - 0 ma V = 3 V, 8 V Notes: a. Refer to PROESS OPTION FLOWHART. b. = 2, = as determined by the operating temperature suffix. c. Typical values are for ESIGN AI ONLY, not guaranteed nor subject to production testing. d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. e. Guaranteed by design, not subject to production test. f. V IN = input voltage to perform proper function. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ynamic haracteristics Turn-On Time t ON R L = 300, L = 3 pf Hot Turn-Off Time t OFF V S = 8 V, see figure 2 Hot Break-Before-Make G43HS only, V t S = 8 V Time elay 60 R L = 300, L = 3 pf harge Injection Q V g = 6 V, R g = 0, L = nf 60 p Power Supplies Positive Supply urrent I+ Hot Negative Supply urrent I- Hot = 3.2 V, V IN = 0 or V Logic Supply urrent I L Hot Ground urrent I GN Hot Unit ns µa 4 ocument Number: 7203 S3-283-Rev., 27-May-3 THE PROUTS ESRIBE HEREIN AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9000

5 TYPIAL HARATERISTIS (2, unless otherwise noted) G4HS, G42HS, G43HS r S(on) - rain-source On-Resistance (Ω) ± 8 V ± V T A = 2 ± 0 V ± 2 V ± V ± 20 V rs(on) - rain-source On-Resistance (Ω) = 3.0 V = 3 V =.0 V T A = 2 = V = 8.0 V = 2.0 V =.0 V V - rain Voltage (V) On-Resistance vs. V and ual Supply Voltage = 20.0 V V - rain Voltage (V) On-Resistance vs. V and Unipolar Supply Voltage I S, I (pa) = + V = - V = V I (on) I S(off) I (off) r S(on) - rain-source On-Resistance (Ω) = V = - V = V V or V S - rain or Source Voltage (V) Leakage urrent vs. Analog Voltage V - rain Voltage (V) On-Resistance vs. V and Temperature r S(on) - rain-source On-Resistance (Ω) = 2 V = 0 V = V V - rain Voltage (V) On-Resistance vs. V and Temperature LOSS, OIRR, X TLAK (db) K M OIRR LOSS X TALK = V = - V = V R L = 0 Ω 0 M 00 M G Frequency (Hz) Insertion Loss, Off-Isolation, rosstalk vs. Frequency ocument Number: 7203 S3-283-Rev., 27-May-3 THE PROUTS ESRIBE HEREIN AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9000

6 G4HS, G42HS, G43HS TYPIAL HARATERISTIS (2, unless otherwise noted) Q - harge Injection (p) V = ± V V = ± 2 V Q - harge Injection (p) V = ± V V = ± 2 V V - rain Voltage (V) harge Injection vs. Analog Voltage V S - Source Voltage (V) harge Injection vs. Analog Voltage = V = - V = V = 2 V = 0 V = V T ON/ T OFF (ns) t ON t OFF T ON/ T OFF (ns) t ON t OFF Temperature ( ) Switching Time vs. Temperature Temperature ( ) Switching Time vs. Temperature 00 ma 0 ma = V = - V = V ma = SW = 4 SW I+, I- I SUPPLY 00 µa 0 µa I L µa 00 na 0 na 0 00 k 0 k 00 k M 0 M f - Frequency (Hz) Supply urrent vs. Input Switching Frequency 6 ocument Number: 7203 S3-283-Rev., 27-May-3 THE PROUTS ESRIBE HEREIN AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9000

7 G4HS, G42HS, G43HS SHEMATI IAGRAM (Typical hannel) S V IN Level Shift/ rive GN Figure. TEST IRUITS ± 0 V + V S IN GN + V R L 300 Ω L 3 pf Logic Input Switch Input* 3 V 0 V V S 0 V 0 % t ON 90 % t r < ns t f < ns t OFF 90 % - V L (includes fixture and stray capacitance) R O = V S R L + r S(on) Note: Logic input waveform is inverted for switches that have the opposite logic sense control Figure 2. Switching Time + V + V V S V S2 S IN S 2 IN 2 GN 2 R L2 300 Ω 2 L2 3 pf R L 300 Ω L 3 pf Logic Input Switch Output Switch Output 3 V 0 V V S 0 V V S2 2 0 V 0 % 90 % t 90 % t - V L (includes fixture and stray capacitance) Figure 3. Break-Before-Make (G43HS) ocument Number: 7203 S3-283-Rev., 27-May-3 7 THE PROUTS ESRIBE HEREIN AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9000

8 G4HS, G42HS, G43HS TEST IRUITS Δ + V + V R g S IN X OFF ON OFF V g 3 V IN GN L nf IN X OFF ON Q = Δ x L OFF - V Figure 4. harge Injection + V + V V S S R g = 0 Ω 0 V, 2.4 V IN 0 Ω N S V, 2.4 V IN 2 R L GN X TALK Isolation = 20 log = RF bypass V S Figure. rosstalk - V + V + V + V + V V S R g = 0 Ω 0 V, 2.4 V S IN R L 0 Ω S Meter GN - V Off Isolation = 20 log V S = RF Bypass Figure 6. Off-Isolation 0 V, 2.4 V IN GN - V HP492A Impedance Analyzer or Equivalent Figure 7. Source/rain apacitances maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see /ppg? ocument Number: 7203 S3-283-Rev., 27-May-3 THE PROUTS ESRIBE HEREIN AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9000

9 Package Information JEE Part Number: MS E im Min Max Min Max A A B E e.27 BS 0.00 BS H L EN: S Rev. F, 09-Jul-0 WG: 300 H All Leads e B A L 0.0 mm IN ocument Number: Jul-0

10 Package Information E E S Q A A L B e B e A MAX im Min Max Min Max A A B B E E e e A L Q S EN: S Rev., 09-Jul-0 WG: 482 ocument Number: Jul-0

11 Package Information E E S Q A A L L B e B e A im Min Max Min Max A A B B E E e 2.4 BS 0.00 BS e A 7.62 BS BS L L Q S EN: S Rev. G, 09-Jul-0 WG: 403 ocument Number: Jul-0

12 Packaging Information A e L 28 2 E A im Min Max Min Max BS 0.00 BS EN: S Rev. B, 09-Jul-0 WG: 32 L B ocument Number: Jul-0

13 QFN 4x4-6L ase Outline Package Information () (4) VARIATION VARIATION 2 IM MILLIMETERS () INHES MILLIMETERS () INHES MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. A A A ref ref ref ref. b BS 0.7 BS 4.00 BS 0.7 BS e 0.6 BS BS 0.6 BS BS E 4.00 BS 0.7 BS 4.00 BS 0.7 BS E K 0.20 min min min min. L N (3) Nd (3) Ne (3) Notes () Use millimeters as the primary measurement. (2) imensioning and tolerances conform to ASME Y4.M (3) N is the number of terminals. Nd and Ne is the number of terminals in each and E site respectively. (4) imensions b applies to plated terminal and is measured between 0. mm and 0.30 mm from terminal tip. () The pin identifier must be existed on the top surface of the package by using identification mark or other feature of package body. (6) Package warpage max. 0.0 mm. EN: S Rev. B, 22-Apr-3 WG: 890 Revision: 22-Apr-3 ocument Number: 792 For technical questions, contact: powerictechsupport@vishay.com THIS OUMENT IS SUBJET TO HANGE WITHOUT NOTIE. THE PROUTS ESRIBE HEREIN AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9000

14 Application Note 826 REOMMENE MINIMUM PAS FOR SO-6 REOMMENE MINIMUM PAS FOR SO (9.449) (.94) APPLIATION NOTE (6.248) 0.2 (3.86) (0.9) 0.00 (.270) (0.7) Recommended Minimum Pads imensions in Inches/(mm) Return to Index Return to Index ocument Number: Revision: 2-Jan-08

15 Legal isclaimer Notice Vishay isclaimer ALL PROUT, PROUT SPEIFIATIONS AN ATA ARE SUBJET TO HANGE WITHOUT NOTIE TO IMPROVE RELIABILITY, FUNTION OR ESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. ustomers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Revision: 3-Jun-6 ocument Number: 9000