INTRODUCTION Thank yu fr purchasing KOSO RS DYNO digital LCM meter the meter is displayed by lcm with led back light, befre perating, please read the instructin carefully and fllw it t install the meter. NOTICE 1.The lcd meter is apply fr DC 12V. 2.Fr installatin, please fllw the steps described in manual. Any damage caused by wrng installatin shall be imputed t the users. 3.Dn't break r mdify the wire terminal. T avid the shrt circuit, please dn't pull the wire when installing. 4.D nt disassemble r change any parts excluding the manual descriptin. 5.The interir examinatin r maintenance shuld be executed by ur prfessinals. MARK MEANING: Yu culd get the installatin details frm the infrmatin behind the mark. Sme prcesses must be fllwed t avid the affectin caused by wrng installatin. WARNING! CAUTION! Cntent 1-1 Accessry 1-2 Optin accessry 2-1 Wiring installatin instructins 2-2 Installatin instructins 3-1 Basic functin instructin 3-2 Standard screen functin instructin 3-3 The buttn functin instructin 3-4 The screen switch instructin 3-5 Main screen functin switch instructin 3-6 Digital screen functin switch instructin 3-7 The setting screen instructin 4 Functin, setting instructin 4-1 Speed unit setting 4-2 Cycle/ pistn setting 4-3 The temperature unit setting 4-4 Speeding warning light setting 1-1 4-5 Over RPM warning light setting Sme prcesses must be fllwed t avid damages t yurself r the public. Sme prcesses must be fllwed t avid the damage t the vehicle. 4-6 Over temperature (Water temperature) warning light 1 setting 4-7 Over temperature (Oil temperature) warning light 2 setting 4-8 Tire size adjustment/ sensr pint setting instructin 4-9 The clck setting instructin 4-10 Fuel sensr impedance & insufficient fuel warning setting instructin 4-11 The target speed timer / target distance timer setting 5-1 Target speed timer test 5-2 Target distance timer test 5-3 The tp speed test 6 Truble shting 7 Guarantee & ntice f prducts 8 Guaranty 1-1 1 4 7 10 Accessry 2 Meter X 1 Main wiring X 1 RPM wire set (Type B) X 1 Digital speed signal sensr X 1 M8/ S type speed sensr bracket X 1 Next page 5 8 Temp sensr wire set X 2 D6 X 5L mm magnet X 6 3 6 9 M10/ S type speed 11 12 sensr bracket X 1 TEMP 2 TEMP 1 RPM wire set (Type A) X 1 PT1/8 water temp sensr X 2 Cnnect terminal X 7 M5 X 5L hexagnal blt X 2
1-1 2.5 mm spanner 4 mm spanner 13 14 15 X 1 Accessry X 1 Meter bracket X 1 set 1-2 Optin accessry 1 Disc magnet screw 5/16-18 X 22.1L M5 X P0.8 X 12L M6 X P1.0 X 12.6L M6 X P1.0 X 19.7L M6 X P1.0 X 24L M8 X P1.25 X 22.5L M8 X P1.25 X 27.5L M8 X P1.25 X 29L M10 X P1.25 X 28.3L 2 Active speed sensr 3 Oil temp sensr adapter M12 X P1.5 X 15L M14 X P1.25 X 15L M14 X P1.5 X 15L M16 X P1.5 X 15L M18 X P1.5 X 15L M20 X P1.0 X 15L M20 X P1.5 X 15L 16 M5 X 12L screw X 2 M5 X 18L screw 17 X 2 18 M5 gasket X 2 4 Water temp sensr adapter 5 Cylinder head temp sensr 6 Temp sensr M14 M16.M18 M22.M26 mm M10. M14 mm M10 X P1.0 M12 X P1.5 M14 X P1.25 M14 X P1.5 M16 X P1.5 / M18 X P1.5 19 Manual 7 L type speed sensr bracket 8 Meter bracket Please cntact us if the items yu pen are nt the same, with the abve-listed nes. Sme f the ptin accessries may nt be sld. Fr the details, please cntact the lcal distributr.
2-1 Wiring installatin instructins Meter (Accessry 1) Yellw / fuel (-) Green / white- neutral (-) Gray / il light (+12V/-) Orange / L turn signal (+12V) Blue / R turn signal (+12V) TEMP 2 TEMP 1 Water temperature Oil temperature Temp sensr wire (Accessry 5) PT1/8 (Accessry 6) Please install the temp sensr t the psitin yu want t measure. Main wiring (Accessry 2) Black / Grund wire cnnect t the vehicle bdy r the engine (It must be a gd grund) Brwn / RPM Digital speed signal sensr (Accessry 7) Pick-up Ignitin cntrl bx RPM wire set-type A (Accessry 3) YAMAHA HONDA SUZUKI SYM Red / "+"Wire cnnect key n DC 12V main pwer switch Main switch wiring reference: "+" Clr "-" Clr Brwn Black Brwn Black Black Green Black Green The clr listed abve may differ depending n the mdel. Fuel indicatr wiring reference: YAMAHA HONDA SUZUKI SYM Green Yellw/white Yellw/white Yellw/white The fuel sensr is electrnic type, please dn't parallel cnnectin with the riginal, therwise the fuel gauge wn't display. The wrng installatin f the fuel wiring may cause the meter brken. RPM wire set-type A (Accessry 3) RPM wire set-type B (Accessry 4) Spark plug wire Magnet (Accessry 8) The ignitin cil psitive electrde The nrth (N) side f magnet must face t the sensr when installing. If yu dn't cnnect the fuel wiring, the fuel gauge will nt display. When cnnecting the pwer wiring, please fllw the instructin. If yu cnnect the red & brwn wiring in parallel will cause the meter wrk imprperly. We prvide 2 ways t get the RPM signal-sensr A & sensr B. If there are interruptins, yu culd change the sensr wiring t get better signal. CAUTION! Just wind the RPM wire(a) nt the spark plug wire. D nt cnnect them! We als suggest yu t replace the "R" type spark plug in the mean time t get better signal. Fr the mdel mre than ne pistn, please catch the signal frm the first cylinder cil wire. Fr the mdel with mre than ne pistn, please just cnnect the RPM sensr wiring t ne f the ignitin cil psitive electrdes. Please make sure that the ignitin cil psitive electrde befre cnnecting the RPM sensr wiring! Wrng installatin will cause the meter brken!
2-2 Installatin instructins MOTO/SCOOTER S type speed sensr bracket instructin 2. Put the magnet int the brake disc screw hle. Install the s type sensr bracket. Adjust the sensr bracket psitin t make sure that the sensr culd face the magnet t prevent bad speed signal r n signal! 7. 6. When installing, please fllw the prcess 1.M5 X 12L screw X 2 6.Meter fixed bard 2.Meter bracket fr handle bar 7.Fix the meter n the bard (6) 3.Fix the bracket n handle bar with the screw (5) (7/8 inch) 8.Fix the meter and the bracket tgether 4.M5 X 18L screw X 2 Please adjust the meter t the 5.M5 washer X 2 best visible angle befre tightening the screw ATV S type speed sensr bracket instructin 1 Insert the signal magnet. (Yu need t dig a hle by yurself). 2 Install the s-type sensr bracket, yu culd adjust the prper distance and angle t fit different mdel. 3 After installing the sensr, please adjust the distance between sensr and magnet. Please keep the distance in 8 mm. Abut the setting, please refer t 4-8 tire size adjustment/ sensr pint setting instructin 4. 5. 1. 2. 2 3. 1 Magnet (fr speed signal) 3 Speed sensr S type sensr bracket Install the speed sensr n the bracket. P.S. MOTO/SCOOTER MAGNET BELOW 8mm The mre magnet sensr pints are, the less the display interval is. When installing the magnet, please put the magnet with N-mark side face the utside and put them averagely t avid wrng signal. EX. 1: If yur disk has 3 screws, yu culd install 1 r 3 magnets t catch the speed. L type speed sensr bracket instructin Use the bind & the nn-slip rubber t fix bracket t the frnt f the shck and adjust the prper height and angle. SPEED SENSOR Adjust the distance between sensr and magnet. We suggest yu t make sure the distance is under 8mm fr catching gd speed signal. EX. 1 EX. 2 EX. 3 EX. 4 EX. 2: If yur disk has 4 screws, yu culd install 1 2 r 4 magnets t catch the speed. EX. 3: If yur disk has 5 screws, yu culd install 1 r 5 magnets t catch the speed. EX. 4: If yur disk has 6 screws, yu culd install 1 2 3 r 6 magnets t catch the speed. After finishing the magnet installatin and sensr pint setting, please mve yur tire t test the speedmeter wrk r nt. Put the magnet int the brake disc screw hle. Speed sensr installatin find a prper hle t put the sensr in and fix it by hexagnal blt. MAGNET BELOW 8mm SPEED SENSOR Please keep the distance between sensr and magnet in 8 mm t avid bad signal.
3-1 Basic functin instructin 3-2 Standard screen functin instructin Speedmeter Display range: 0~360 km/h (0~223 MPH). Display unit: km/h r MPH can be changed. Speeding warning light Setting range: 30~180 km/h (19~112 MPH). Setting unit: 1 km/h (MPH). Water/ il indicatr Display range: 0~150 C (32~ 302 F) 10 levels, each level represents 15 C (27 F). Display unit: C/ F fr alternative. Over temperature warning light Setting range: 50~150 C (122~ 302 F). Setting unit: 1 C ( F). Fuel indicatr Display unit: 10 levels, each level represents 10 %. Fuel indicatr: 100 Ù, 510 Ù, n display. Fuel warning Setting range: 10~50 %. Setting unit: 10 %. Vltage indicatr Display range: DC 9.5~24.0 V. Display unit: DC 0.1 V. Od meter Display range: 0~99999.9 km/h, and then restart frm 0. Display unit: km/h r MPH can be changed. 37 mm Indicatr lights Frm left t right: ver RPM, speeding, ver temperature (water) warning light 1, ver-temperature (il) warning light 2, natural, flash light, and il lights. Dwn Tachmeter Display range: 0~9,000/ 18,000 RPM. Display unit: 500 RPM. Over-RPM warning light Setting range: 3,000~22,000 RPM. Setting unit: 100 RPM. Trip meter Display range: 0~999.9 km/h, and then restart frm 0, manually r autmatically. Display unit: km/h r MPH can be changed. Clck 24 H. 81 mm Exit Enter Indicatr lights Frm left t right: ver RPM, speeding, ver temperature (water) warning light 1, ver-temperature (il) warning light 2, natural, flash light, and il lights. Dwn Vltage indicatr Display range: DC 9.5~24.0 V. Display unit: DC 0.1 V. Tachmeter Display range: 0~22,000 RPM. Display unit: 100 RPM. Over-RPM warning light Setting range: 3,000~22,000 RPM. Setting unit: 100 RPM. Exit Enter Water/ il indicatr Display range: 0~150 C (32~302 F) Display unit: C/ F fr alternative. Over temperature warning light Setting range: 50~ 150 C (122~302 F). Setting unit : 1 C ( F). Fuel indicatr Display unit: 10 levels, each level represents 10 %. Fuel indicatr: 100 Ù, 510 Ù, n display. Fuel warning Setting range: 10~50 %. Setting unit: 10 %. Speedmeter Display range: 0~360 km/h (0~223 MPH). Display unit: km/h r MPH can be changed. Speeding warning light Setting range: 30~180 km/h (19~112 MPH). Setting unit: 1 km/h (MPH). Od meter Display range: 0~99999.9 km/h, and then restart frm 0. Display unit: km/h r MPH can be changed. Trip meter Display range: 0~999.9 km/h, and then restart frm 0, manually r autmatically. Display unit: km/h r MPH can be changed. Clck 24 H. 138 mm 49 mm
3-3 The buttn functin instructin BUTTON Press buttn ne time t enter the setting screen r t back t the main screen frm any screens. 3-4 The screen switch instructin In setting screen: Press buttn screen. t get back t the main BUTTON X 3 SECONDS In the screen with trip meter, hld dwn buttn fr 3 secnds t reset the trip meter. BUTTON Press buttn t switch between main screen, digital screen, and the pwer test screen. In main screen: Press buttn setting screen. In main screen: Press buttn digital screen. In digital screen: Press buttn screen. t enter the t enter t enter the Pwer test BUTTON In main/digital screen, press buttn t select the functin display between water temperature, il temperature, and the fuel. (Please refer t 3-4 & 3-5) In setting screen, press buttn t select the screen yu want t make the setting. (Please refer t 3-6) In functin setting screen, press buttn t select the units and increase the setting value (like the figure belw), press r hld dwn t increase the setting value autmatically. BUTTON In main/digital screen, press buttn t select the functin display between dmeter, trip meter and clck. (Please refer t 3-4 & 3-5) In setting screen, press buttn t select the screen yu want t make the setting. (Please refer t 3-6) In functin setting screen, press buttn t select the units and decrease the setting value (Like the figure belw), press r hld dwn t decrease the setting value. In pwer test screen: Press buttn t back t the main screen. Press buttn t return t the main screen in any screen.
3-5 Main screen functin switch instructin In main screen: Press buttn t switch the il temperature t the fuel indicatr. EX. Nw the left-side screen displays the il temperature. 3-6 Digital screen functin switch instructin In digital screen: Press buttn t switch the il temperature t the fuel indicatr. EX. Nw il temperature is 28.5 C. In main screen: Press buttn t switch the fuel indicatr t the water temperature. EX. Nw the left-side screen displays the Fuel. In digital screen: Press buttn t switch the fuel indicatr t the water temperature. EX. Nw fuel indicatr is full. In main screen: Press buttn t switch the water temperature t the il temperature. EX. Nw the left-side screen displays the il temperature. In main screen: Press buttn the dmeter t trip meter. EX. Nw the screen displays the dmeter. t switch In digital screen: Press buttn t switch the water temperature t the il temperature. EX. Nw water temperature is 28.5 C. In digital screen: Press buttn t switch the dmeter t trip meter. EX. Nw the dmeter is 0 km. In main screen: Press buttn t switch the trip meter t clck. EX. Nw the screen displays the trip meter. In digital screen: Press buttn switch the trip meter t clck. EX. Nw the trip meter is 0 km. t In main screen: Press buttn t switch t the dmeter. EX. Nw the screen displays the clck. In digital screen: Press buttn the dmeter. EX. Nw the time is 0:00. t switch t
3-7 +1 +2 +3 +4 +5 The setting screen instructin -10-9 -8 Press buttn t select the screen yu want, in rder f S-1, S-2,S-3. Press buttn t select the screen yu want, in rder f S-11, S-10, S-9, S-8. -11-1 +11-7 -6 +6 When entering the setting screen, if yu dn't press any buttns after 30 secnds, it will return t the main screen autmatically. -2-3 -4-5 +10 +9 +8 +7 4 Functin, setting instructin Speedmeter Display range: 0~360 km/h (0~223 MPH) Display unit: km/h & MPH fr alternative Display internal <0.5 secnd Odmeter 0~99999.9 km, reset autmatically after 99999.9 km. Trip meter 0~999.9 km, reset autmatically after 999.9 km Speeding warning light Setting range: 30~180 km/h (19~112 MPH) Setting unit: 1 km/h (MPH) Tire circumference Setting range: 1,000~2,500 mm Setting unit: 1 mm Sensitive pint: 1~6 Needle tachmeter Display range: 0~9,000/ 18,000 RPM Display unit: 500 RPM Digital tachmeter Display range: 0~22,000 RPM Display unit: 100 RPM Display internal <0.5 secnd Over RPM warning light Setting range: 3,000~22,000 RPM Setting unit: 100 RPM Strke / pistn setting 2 Strke: 1, 2, 3, 4 pistns 4 Strke: 1, 2, 3, 4, 5, 6, 8, 10, 12 pistns Temperature Display unit: C & F fr alternative Level water indicatr Display range: 0~150 C (32~302 F), 10 levels Display unit: Each level represents 15 C (27 F) Level il indicatr Display range: 0~150 C (32~302 F), 10 levels Display unit: Each level represents 15 C (27 F) Digital water indicatr Display range: 0~150 C (32~302 F) Display unit: 0.1 C ( F) Digital il indicatr Display range: 0~150 C (32~302 F) Display unit: 0.1 C ( F) Next page
4 Functin, setting instructin 4-1 Display internal <0.5 secnd Over temperature warning Setting range: 50~150 C (122~302 F) (water & il) light Setting unit: 1 C ( F) Fuel indicatr Display range: 10 levels Display unit: Each level represents 10 % Setting range: 100 Ù, 510 Ù, n display Fuel warning Setting range: 10~50 % Setting unit: 10 % Clck 24 H Vlt meter Display range: DC 9.5~24.0 V Display unit: DC 0.1V Display internal <0.5 secnd Target speed timer Setting range: 30~360 km/h (20~220 MPH) Setting unit: 5 km/h (MPH) Target distance timer Setting range: 50~1,000 m (1/32~20/32 mile) Setting unit: 50 m (1/32 mile) Tp speed timer The recrd including, 1.Speed 0~360 km/h (0~223 MPH) 2.Distance 0~999 m (0~3280 feet) 3.Timer 0~9.59.9 secnd. Usage vltage DC 12V Install vltage DC 40V Operating temperature range -10~+60 C Prduct mdel JIS D 0203 S2 Prduct size 126 X 81 X 49 m m Prduct weight Arund 200 g Indicatr light Neutral-green, flash-yellw, il-red Design and Specificatins are subject t change withut ntice! Speed unit setting Press buttn nce (Or the buttn 11 times) t select the speed unit setting screen. Press buttn t enter the setting screen. EX. Nw the riginal setting is km/h. If yu just want t check the setting, press buttn t return t the main screen. Press buttn r t select the speed unit. km/h and MPH is alternative. Nw the km/h is flashing! Press buttn t return t the main screen. EX. The setting is changed frm km/h t MPH. If yu just want t make the setting, press buttn t back t the main screen. Press buttn r t select the ther setting screens.
4-2 Cycle/ pistn setting Press buttn 2 times (Or the buttn 10 times) t select the strkes/pistns setting screen. CAUTION! Make sure the crrect strkes and pistns befre setting. Make sure the input is crrect, r the RPM utput will be incrrect. We define the engine with the ignitin system ignites every 360 degree as 2-strke and the engine with the ignitin system ignites every 720 degree as 4-strke. Sme 4-strke bikes with ne single pistn are igniting every 360 degree nce, s the setting shuld be the same as the bike with 2-strke and ne pistn engine. Press buttn r t select the number yu want t input. 2-strke pistns are 1,2,3,4. 4-strke pistns are 1,2,3,4,5,6,8,10,12. Nw the 1 is flashing! Press buttn t enter the signal impulse setting. EX. The pistn setting is changed frm 1 P (Pistn) t 4 P (Pistns). Press buttn t enter strkes/pistns setting screen. EX. Nw the setting is 2-strke with ne single pistn. If yu just want t check the setting, press buttn t return t the main screen. Press buttn r t select the strke. There are 4-strke and 2-strke. Nw the 2 is flashing! Press buttn r t chse the signal impulse yu want t set. Nw the signal impulse setting is flashing! The signal impulse setting range is between hight (The psitive signal) & lw (The negative signal) If the tachmeter can't detect the signal (N RPM is displayed n the screen), yu culd chse anther setting and check it again. Press buttn t enter pistns setting screen. EX. The setting is changed frm 2-Strke t 4-strke. Press buttn t enter the digital needle tachmeter range setting EX. The input signal is changed frm lw t hight. Next page Next page
4-2 Cycle/ pistn setting Press buttn r t chse the range yu need. The ranges fr selectin are 9,000 RPM and 18,000 RPM. Nw the 9000 is flashing! 4-3 The temperature unit setting Press buttn 3 times (Or the buttn 9 times) t select the temperature unit setting screen. Press buttn t return t strkes/ pistns setting screen. EX. Nw the digital needle tachmeter range is changed frm 9,000 RPM t 18,000 RPM. If yu just want t make the setting, press buttn t back t the main screen. Press buttn t enter the setting screen. EX. Nw the setting unit is C. If yu just want t check the setting, press buttn t return t the main screen. Press buttn r t select the temperature unit. There are C and F fr alternatives. Nw the c is flashing! Press buttn r t select the ther setting screens. Press buttn t return t temperature unit setting screen. EX. The unit setting is changed frm C t F. If yu just want t make the setting, press buttn t back t the main screen. Press buttn r t select the ther setting screens.
4-4 Speeding warning light setting Press buttn 4 times (Or the buttn 8 times) t select the speeding warning light setting screen. Press buttn r t select the ther setting screens. P.S. The speeding warning light is set t be 60 km/h, the red light flashes when speeding. (Like fig. Right) Dwn Exit Enter Dwn Exit Enter Press buttn t enter the speeding warning light setting screen. EX. Nw the setting is 30 km/h. If yu just want t check the setting, press buttn t return t the main screen. Press buttn r t select the number yu want t input. The setting range: 30~180 km/h (19~1 12 MPH). Setting unit: 1 km/h (MPH). Nw the 30 is flashing! Next NEXT page PAGE Press buttn t return t speeding warning light setting screen. EX. The setting is changed frm 30 km/h t 60 km/h. If yu just want t make the setting, press buttn t back t the main screen.
4-5 Over RPM warning light setting Press buttn 5 times (Or the buttn 7 times) t select the ver RPM warning light setting screen. Press buttn r t select the ther setting screens. P.S. The ver RPM warning light will light when the RPM reaches yur setting. (The red light) The yellw light will light t warn yu 500 RPM befre yur setting. Dwn Exit Enter Press buttn t enter the ver RPM warning light setting screen. EX. Nw the setting is 10,000 RPM. If yu just want t check the setting, press buttn t return t the main screen. Dwn Exit Enter Press buttn r t select the number yu want t input. The setting range: 3,000~22,000 RPM. Setting unit: 100 RPM. Nw the 100 is flashing! Next NEXT page PAGE Press buttn t return t ver RPM warning light setting screen. EX. The setting is changed frm 10,000 RPM t 12,000 RPM. If yu just want t make the setting, press buttn t back t the main screen.
4-6 Over temperature (Water temperature) warning light 1 setting Press buttn 6 times (Or the buttn 6 times) t select the ver temperature warning light 1 setting screen. Press buttn r t select the ther setting screens. P.S. If the warning light is set t be 90 C, the red light will flash when the il temperature is ver yur setting. (Like fig. right) Dwn Exit Enter Dwn Exit Enter Press buttn t enter the ver temperature warning light 2 setting screen. EX. Nw the setting is 100 C. If yu just want t check the setting, press buttn t return t the main screen. Press buttn r t select the number yu want t input. The setting range: 50~150 C (122~302 F). Setting unit: 1 C ( F). Nw the 100 is flashing! Press buttn t return t ver temperature warning light 1 setting screen. EX. The setting is changed frm 100 C t 90 C. If yu just want t make the setting, press buttn t back t the main screen. Next NEXT page PAGE
4-7 Over temperature (Oil temperature) warning light 2 setting Press buttn 7 times (Or the buttn 5 times) t select the ver temperature warning light 2 setting screen. Press buttn r t select the ther setting screens. P.S. If the warning light is set t be 90 C, the red light will flash when the il temperature is ver yur setting. (Like fig. right) Dwn Exit Enter Dwn Exit Enter Press buttn t enter the ver temperature warning light 2 setting screen. EX. Nw the setting is 100 C. If yu just want t check the setting, press buttn t return t the main screen. Press buttn r t select the number yu want t input. The setting range: 50~150 C (122~302 F). Setting unit: 1 C ( F). Nw the 100 is flashing! Press buttn t return t ver temperature warning light 2 setting screen. EX. The setting is changed frm 100 C t 90 C. If yu just want t make the setting, press buttn t back t the main screen. Next NEXT page PAGE
4-8 Tire size adjustment/ sensr pint setting instructin Press buttn 8 times (Or the buttn 4 times) t select the tire size adjustment/ sensr pint setting screen. CAUTION! Please measure the circumference f the tire (Please measure the tire which yu will put the magnets n) befre setting and make sure the numbers f the magnets (Installed t the breaking rtr r the screws n the sprcket.) Please make sure all the input value is crrect, r the utput data will be affected. Press buttn t enter the sensr pint setting screen. EX. Nw the circumference is changed frm 1,250 mm t 1,300 mm. Press buttn r t select the number yu want t input. The sensr pint setting range is frm 1 t 6. Nw the 1 is flashing! Press buttn t enter the setting screen. EX. The circumference setting is 1,250 mm and the sensr pint is 1. If yu just want t check the setting, press buttn t return t the main screen. Press buttn t return t the tire size adjustment/ sensr pint setting screen. EX. Nw the sensr pint setting is changed frm 1 t 6. If yu just want t make the setting, press buttn t back t the main screen. P.S. Yu culd define the valve as the starting pint and the terminal pint t measure the wheel circumference with a measuring tape. 130 cm Press buttn r t select the number yu want t input. The setting range: 1,000~2,500 mm. Setting unit: 1 mm. Nw the 1250 is flashing! Press buttn r t select the ther setting screens. Next NEXT page PAGE
4-9 The clck setting instructin Press buttn 9 times (Or the buttn 3 Press buttn t return t the clck setting times) t select the clck setting instructin instructin screen. setting screen. EX. The minute is changed frm 0 t 1. If yu just want t make the setting, press buttn t back t the main screen. Press buttn t enter the clck setting instructin screen. EX. Nw the time is 0:00. If yu just want t check the setting, press buttn t return t the main screen. Press buttn r t select the ther setting screens. Press buttn r t select the number yu want t input. The time range: 0~24 hurs. Nw the 0 is flashing! Press buttn t enter the minutes setting screen. EX. The hur is changed frm 0 t 13. Press buttn r t select the number yu want t input. Nw the 00 is flashing! Next NEXT page PAGE
4-10 Fuel sensr impedance & insufficient fuel warning setting instructin Press buttn 10 times (Or the buttn 2 times) t select the fuel impedance & insufficient fuel warning setting screen. Press buttn r t select the number yu want t input. The setting range: 10~50 %. Setting unit: 10 %. Nw the 30% is flashing! Press buttn t enter the fuel impedance & insufficient fuel warning setting screen. EX. Nw the fuel sensr impedance setting is 100 Ù and the insufficient fuel warning is 30 %. If yu just want t check the setting, press buttn t return t the main screen. Press buttn t return t the previus fuel sensr impedance setting screen. EX. Nw the setting is changed frm 30 % t 20 %. If yu just want t make the setting, press buttn t back t the main screen. P.S. Usually the fuel sensr impedance setting is 100 Ù fr YAMAHA mdels, and 510 Ù fr the HONDA mdels, but smetimes it will differ depending n the mdel. The insufficient fuel warning setting: if the fuel is less than the value yu set, it will flash. (Like fig. right) Press buttn r t select the number yu want t input. Fuel sensr impedance setting range: 100 Ù, 510 Ù and n display. Nw the 100 Ù is flashing! Dwn Exit Enter Press buttn r t select the ther setting screens. Press buttn t enter the insufficient fuel warning setting screen. EX. Nw 100 Ù is changed t 510 Ù. Next NEXT page PAGE
4-11 The target speed timer/ target distance timer setting Press buttn 11 times (Or the buttn nce) t select the target speed timer/ target distance timer setting Press buttn t enter the target speed timer setting screen. EX. The target speed timer setting is 0~50 km/h and the target distance timer setting is 50 m (1/32 mile). If yu just want t check the setting, press buttn t return t the main screen. Press buttn r t select the number yu want t input. The target distance timer setting range: 50~1000 m (1/32~20/32 mile). Setting unit: 50 m (1/32 mile). Nw the 50 is flashing! Press buttn r t select the number yu want t input. The target speed timer setting range: 30~360 km/h (20~220 MPH). Setting unit: 5 km/h (MPH). Nw the 50 is flashing! The setting unit will change tgether with the speed unit setting (4-1). Press buttn t return t the target speed timer/ target distance timer setting EX. Nw the target distance timer setting is changed frm 1/32 mile (50 m) t 2/32 mile (100 m). If yu just want t make the setting, press buttn t back t the main screen. Press buttn t enter the target distance timer setting screen. EX. Nw the target speed timer is changed frm 0~50 km/h t 0~120 km/h. Press buttn r t select the ther setting screens. Next NEXT page PAGE
5-1 Target speed timer test Enter the testing screen if n recrd The recrd display screen Enter the testing screen Next NEXT page PAGE WARNING! Please use this functin at racetrack t avid traffic accidents. In the pwer test screen, press nce (Or the buttn 3 times.) t enter the target speed timer test screen. Please start the test when the bike stps. If yu have the pwer test recrd, it will display the recrd first. Yu must clear the recrd befre starting a new test. Press buttn t enter the test standby screen. EX. The target speed timer test setting is 0~120 km/h, the time t reach the speed is 19.2 secnds, and the distance yu need t reach the speed is 640 meter. If yu just want t check the recrd, press buttn t back t the main screen. When the bike mves, the timer will start autmatically. Nw the target speed timer is flashing! Abut the pwer test setting, please check 4-11. P.S. The timer and trip meter will start t cunt autmatically when yur bike mves. When yu reach the target speed yu set, the timer and trip meter will stp cunting autmatically. Next page 0 km/h 3 km/h Speed up 120 km/h During the test. When yu reach the target speed yu set (0~120 km/h), the timer will stp cunting (19.1 secnd). EX. The dtted line means the previus recrd, and the true line means the new recrd. Fr example, the previus recrd n the left side curve means the time t reach 120 km/h is 19.2 secnds, and the distance yu need is 640 meter. And the new recrd is 19.1 secnds, and the distance is 639 meter. If the speed yu set is t lw (Fr example 30~60 km/h), the curve will discnnect because the sampling is nt enugh.
5-1 Target speed timer test 5-2 Target distance timer test P.S. Press buttn t save the recrd and then enter the new recrd screen. When yu save the new recrd, the previus recrd will be replaced. Press buttn t delete the recrd and back t the previus recrd screen. The recrd screen. If yu already finished the test, press buttn t back t the main screen. If yu want t make anther test, press buttn t enter the test standby screen. 0 km/h 3 km/h Speed up Test failure T stp the timer during the test: 1.Press buttn, the timer will stp right away and then enter the recrd screen. 2.Press any buttn t enter the recrd screen. 3.Press buttn t save the recrd and enter the recrd screen r press buttn t delete the recrd and enter the previus recrd screen. 4.Press buttn t enter the target speed timer test? standby screen. Enter the testing screen if n recrd The recrd display screen Enter the testing screen WARNING! Please use this functin at racetrack t avid traffic accidents. In the pwer test screen, press 2 times (Or the buttn 2 times.) t enter the Target distance timer test screen. Please start the test when the bike stps. If yu have the pwer test recrd, it will display the recrd first. Yu must clear the recrd befre starting a new test. Press buttn t enter the test standby screen. EX. The target distance timer test setting is 100 meters (2/32 mile) the time t reach the distance is 10.2 secnds, and the tp speed yu reach during the test is 63 km/h. If yu just want t check the recrd, press buttn t back t the main screen. When the bike mves, the timer will start autmatically. Nw the target distance timer is flashing! Abut the pwer test setting, please check 4-11. Next NEXT page PAGE
5-2 Target distance timer test P.S. The timer and trip meter will start t cunt autmatically when yur bike mves. When yu reach the target distance yu set, the speedmeter and timer will stp cunting autmatically. 0km/h 3 km/h Speed up 63 km/h Press buttn t save the recrd and then enter the new recrd screen. When yu save the new recrd, the previus recrd will be replaced. Press buttn t delete the recrd and back t the previus recrd screen. During the test. The recrd screen. If yu already finished the test, press buttn t back t the main screen. If yu want t make anther test, press buttn t enter the test standby screen. Next page When yu reach the target distance yu set (100 m. 2/32 mile), the timer will stp cunting (10.2 secnd). EX. The dtted line means the previus recrd, and the true line means the new recrd. Fr example, the previus recrd n the left side curve means the time t reach 100 km/h is 10.2 secnds, and the tp speed yu reach is 63 km/h. And the new recrd is 10.1 secnds, and the tp speed yu reach is 64 km/h. Press any buttn t enter the recrd screen. If the distance yu set is shrt (fr example 50 r 100 meters), the curve will discnnect because the sampling is nt enugh. P.S. 0 km/h 3 km/h Speed up 0 km/h T stp the timer during the test: 1.Press buttn, the timer will stp right away and then enter the recrd screen. Test failure 2.Press any buttn t enter the recrd screen. 3.Press buttn t save the recrd and enter the recrd screen r press buttn t delete the recrd and enter the previus recrd screen. 4.Press buttn t enter the target distance timer test? standby screen.
5-3 The tp speed test Enter the testing screen if n recrd The recrd display screen Enter the testing screen WARNING! Please use this functin at racetrack t avid traffic accidents. In the Pwer test screen, press 3 times (Or the buttn nce.) t enter the tp speed test screen. Please start the test when the bike stps. If yu have the pwer test recrd, it will display the recrd first. Yu must clear the recrd befre starting a new test. Press buttn t enter the test standby screen. EX. Nw yu culd see the recrd yu have befre. It displays the tp speed is 130 km/h, the distance t reach the tp speed is 751 m, the time yu need t reach the tp speed is 20.8 secnds. If yu just want t check the recrd, press buttn t back t the main screen. When the bike mves, the timer will start autmatically. Nw the pwer test is flashing! The tp speed test range: Speed: 0~360 km/h (0~223 MPH). Distance: 0~999 m (3280 feet) Timer: 0~9.59.9 secnds. The setting unit will change tgether with the speed unit setting (4-1). P.S. The timer is autmatic, s when yur bike start t mve, the timer will start t cunt the time and stp autmatically after yu stps the bike. 0 km/h 3 km/h Speed up 120 km/h During the test. When yu reach the tp speed (130 km/h), the meter will stp cunting the distance (751 m), and time (20.8 secnds). EX. The dtted line means the previus recrd, and the true line means the new recrd. Fr example, the tp speed is 130 km/h, the time t reach it is 20.8 secnds, and the distance yu need is 751m in the previus recrd. And the tp speed is 131 km/h, the time t reach it is 20.8 secnds, and the distance yu need is 751 m in the new recrd. Press any buttn t enter the recrd screen. Press buttn t save the recrd and then enter the new recrd screen. When yu save the new recrd, the previus recrd will be replaced. Press buttn t delete the recrd and back t the previus recrd screen. Next NEXT page PAGE Next page
5-3 The tp speed test The recrd screen. If yu already finished the test, press buttn t back t the main screen. If yu want t make anther test, press buttn t enter the test standby screen. 6 Truble shting The fllwing situatin d nt indicate malfunctin f the meter. Please check the fllwing befre taking it in fr repair. Truble Check item N display Please check the pwer wiring. Please check the wiring is cnnected the wiring and fuse are nt brken. The battery is brken r the utput pwer is nt enugh. D yu replace the spark plug with "R" type ne? (N RPM display) Incrrect date appear Please check the input pwer is DC 12V. If the vltage is insufficient, please change the battery. Speed des nt appear r Please make sure the cable is cnnected appear incrrectly crrectly. Please check the tire-size setting. Please refer t the manual 4-8. Tachmeter des nt appear r appear incrrectly Fuel gauge des nt appear r appear incrrectly Temp des nt appear r appear incrrectly The clck appear Incrrectly Please check the rpm sensr wiring is cnnected crrectly. Please check yur setting. Please refer t the manual 4-2. Please check yur fuel tank. Is there any fuel indicatr? Please check the pwer. Is the pwer n? Please check the wiring. D yu cnnect the wiring crrectly? Please check the setting. Please refer t the manual 4-10. Please check the sensr. is the wiring brken r falling ff? If yu dn't ride the mtrcycle fr a lng time, the capacitance will lse pwer and the recrd will be reset. the capacitance will recharge after yu start riding the bike. If yu still can't slve the prblems accrding t the steps abve, please cntact with distributrs r us.
7 Guarantee & ntice f prducts We hpe ur prducts are perfect. Shuld it happened that ur prducts were bad qualities, we wuld d ur best t exchange the same items t yu. Furthermre, we aplgize we culd nt exchange the items with breakdwns r damages by human. (The guarantee standards are n the basis f the fllwing rules.) The guarantee rules f prducts 1.Prblems are happened when nrmal perating accrding t the ntes f the manual in the guarantee time, please bring the prduct t distributrs r us and we will repair fr free. 2.If breakdwns are happened in the guarantee time, please bring t distributrs r us and present us the guarantee and the details describing the damages situatins. 3.It culdn't be repaired if it is a prize, but yu can cntact with us. 4.We will charge yu fr repairing under the fllwing situtatins even in the guarantee time: 1 N guarantee. 2 N custmer's name, purchase date, distributr's name, and/r change the characters in the guarantee. 3 The damage is caused by being perated with mistakes, repaired rughly, disassembled and refitted. 4 The damage is caused by being fell dwn t the grund r being watered. 5 The damage is nt caused by the electric pwer. Fr example: Fire, earthquake, wind, rain, thunder, r visitatin etc. 5.The guarantee is nly available in yur cuntry. The guarantee time is an advantage f cnsumers fr repairing free. If yur prduct needs t be repaired but the guarantee time has passed r yu dn't remember where yu bught, please cntact with us.