AMP Standard Terminals and Splices. RoHS. Ready

AMP Standard Terminals and Splices RoHS Ready

Table of Contents Product Facts Solderless terminals and splices performs up to today s standards for reliable termination in applications ranging from control circuits to heavy duty power wiring This catalog describes only standard terminals and splices accommodating wire sizes from 2 AWG through 4/0 AWG These terminals are preinsulated and color coded by wire size for easy identification Funnel entry on many terminals allows for easy wire insertion for high speed production Nylon or vinyl insulation provides high dielectric strength The serration or dimple feature inside the terminal barrel provides exceptional barrel contact and tensile strength Special plating process creates a high resistance to corrosion Use of AMP application tooling is designed for uniform high quality terminations UL, CSA, Military Approved Table of Contents Introduction...2, 3 Performance Specifications... 4, 5 Terminal Stud Hole Sizes... PIDG (Pre-Insulated Diamond Grip)...7-32 Terminals... 8-30 Splices...31, 32 PIDG FASTON... 33-3 Terminals... 34, 35 Splices...3 PLASTI-GRIP...37-52 Terminals...38-49 Splices...50-52 TERMINYL...53-5 Terminals... 54, 55 Splices...5 CERTI-SEAL... 57, 58 Splices and Tooling...58 Class 1 and Class 2 Military Approvals...59-5 Tooling...-70 Part Numerical Index...71-73 Global Contacts...74 Numerical values To convert U.S. customary unit values in this catalog to their metric equivalents, use the following formulas: To convert from to Multiply by inch millimeter (mm) 2.540000 x inch metre (m) 2.540000 x -2 inch centimeter (cm) 2.540000 foot metre (m) 3.0480000 x -1 pound-force newton (N) 4.448222 bar pascal (Pa) 1.000000 x 5 pound-force/inch 2 pascal (Pa).894757 x 3 pound-mass kilogram (kg) 4.535924 x -1 ounce-mass kilogram (kg) 2.834952 x -2 To convert wire size (AWG) to the equivalent metric value using the circular mil area of the wire, use the following formula: circular mil area (CMA)/1550.003 = square millimeter (mm 2 ) Note: Dimensions in this catalog are for reference purposes only. Customer drawings are available on request. Specifications subject to change. Consult Tyco Electronics for latest design specifications. Need more information? Call Technical Support: 1-800-522-752 The Center is staffed with specialists well versed in Tyco Electronics products. They can provide you with: Technical Support Catalogs Technical Documents Product Samples 1977, 1980, 1982, 1985, 198, 1988, 1995, 2000 and 2008 by Tyco Electronics Corporation. All Rights Reserved. AMP, AMP-O-LECTRIC, AMPOMATOR, TETRA-CRIMP, AMP-TAPETRONIC, AUTO-PRO, CERTI-SEAL, DYNA-CRIMP, FASTON, PIDG, PLASTI-GRIP, PRO- CRIMPER, SHUR-PLUG, TERMINYL, T-HEAD, TE logo and Tyco Electronics are trademarks. 2

Terminals and Splices PIDG Terminals and Splices Page 7 ( Restricting Terminals also) PIDG FASTON Terminals and Splices Page 33 ( Restricting Terminals also) PLASTI-GRIP Terminals and Splices Page 37 Terminals and Splices TERMINYL Terminals and Splices Page 53 CERTI-SEAL Splices Page 57 3

Terminals and Spices (Continued) Ordering Information Standard Packaging Quantities Terminals and Splices This catalog is designed for easy selection of terminal type to meet your needs. All terminals and splices are cataloged by tongue type and wire size. If the part number is known, refer to the numerical index at the back of this catalog for page location of tabular information. In many instances the part is available in loose piece as well as tape mounted. FASTON terminals are available in strip form. When ordering tape mounted parts, specify the terminal or splice part number, the total quantity of parts required, the part number of the tooling to be used and the type of packaging desired (if applicable). The table shown at top right, lists the wire sizes available and the quantity per package for tape mounted and loose piece. Insulated terminals and splices are color coded to indicate wire range and to help match the terminal with the appropriate tool. The table shown at right identifies the specific wire range insulation color. Range AWG Packaging Quantity Loose Piece Tape Mounted 2-22 1M/Box 2,500/Reel 22-14 1M/Box 5,000/Reel 1-14 H.D. 500/Box 2,500/Reel 12-500/Box 2,500/Reel 8 thru 4 0/Box 2 thru 4/0 50/Box Note: Package quantities may vary with specific part numbers. Color Code Color Code Range AWG Comments 2-22 Transparent 24-20 22-1 1-14 /Black 1-14 Heavy Duty 12-8 4 2 1/0 2/0 3/0 4/0 Terminals and Splices Performance Specifications For detailed test information and product specifications, request appropriate report or refer to the applicable specification listed in the following table. Product Type Test Report Number Application Specification PIDG Terminals Nylon 501-31 MIL-T-7928 PIDG Restriction GPR-575-9 Terminals 1-23 MIL-T-7928/1 PIDG FASTON Terminals UL3 PLASTI-GRIP Terminals 1-11514 UL48 TERMINYL Terminals 1-178 MIL-T-7928 CERTI-SEAL Terminals 4

Terminal and Splices Performance Specifications (Continued) The many millions of AMP terminals and splices that have given ten, fifteen and twenty years of service are ample proof of the testing and research that went into their design and manufacturing. Like all AMP solderless wiring devices, they are thoroughly tested to conform to standards of performance under heavy usage. Tests conducted in Tyco Electronics laboratories and research facilities, some of the best-equipped in their field, indicate that these terminals and splices meet or exceed applicable industrial requirements and military specifications. The result of some of the most popular tests are tabulated here. Upon request, a formal test report will be supplied to support these values and document additional performance requirements not listed. MIL-T-7928 Group III Group VI Tensile Strength After Tensile Strength After Wire Spec. Vibration - Lb. Corrosion - Lb. Size Min. lb. Terminal Type Terminal Type PIDG PIDG 2 7 11.7.7 24 19.8 19.2 22 15 29.0 23.5 20 19 37.7 4.5 18 38 58.9 70.5 1 50 78.5 81.9 14 70 0 5 12 1 209 213 150 247 282 TERMINYL TERMINYL 8 225 299 3 300 00 09 4 400 784 835 2 550 1,035 1,13 1/0 700 1,781 1,77 2/0 750 1,787 1,721 3/0 825 2,845 2,880 4/0 875 3,048 3,28 Terminals and Splices MIL-T-7928 Group II Group III Group VI Wire Specification Millivolt Drop After Millivolt Drop After Millivolt Drop After Size Maximum Current Cycling 2 Vibration 2 Corrosion 2 Millivolt Drop 1 Terminal Type Terminal Type Terminal Type PIDG PIDG PIDG 2 9.2 3.2 3.1 3.3 24 7.9 2. 4.9 2.9 22 9.0 4.5 3.8.0 20 7.5 3. 3.8 3. 18 7.2 3.1 3. 3.1 1 7.7 3. 3.7 3.9 14 7.7 3.7 4.0 3. 12 8.4 4.0 4. 4.2 7.5 3.3 3. 3.3 TERMINYL TERMINYL TERMINYL 8 5.2 3.7 3.8 4.2 5.7 4.3 4.1 4.1 4 5.4 4.1 4.0 4.1 2 5.5 4.2 4.2 4.2 1/0.8 4.4 4.3 4.4 2/0.7 4.2 4.2 4.2 3/0.3 4.2 4.1 4.1 4/0.4 4.0 4.1 4.1 1 Value is millivolt drop permitted after test plus equal length of wire. 2 Value includes equal length of wire. 5

Terminal Stud Hole Size Use to Select Proper Size Terminal The chart shows sizes and dimensions of various studs and the corresponding terminal stud hole sizes used with AMP devices. For example, with stud #5 ( Diameter), use AMP device listed for #5 stud (.129 Hole Diameter). Terminal stud hole sizes may easily be checked by fitting sample terminal to black circle. Terminal Stud Hole Sizes Stud Size Minimum Terminal Stud Dia. U.S. Cust. Metric Hole Diameter #0.00.04 #1.073.077 #2 M2.08.090 #3.099.3 #4.112.11 Stud Size Stud Dia. Minimum Terminal U.S. Cust. Metric Hole Diameter 5/8" M1.25.51 3/4".750.77 #5 M3.129 # M3.5.138.142 #8 M4.14.18 7/8" M22.875.901 #.190.194 #12.21.220 #14.242.245 1" 1.000 1.02 1/4" M.20 5/1" M8.323 1 1/8" 1 1.151 3/8".375.385 7/1".437.448 1 1/4" 1 1.27 1/2" M12.500.5

PIDG Terminals and Splices Product Facts Pre-insulated terminal designed for uniform reliability in most difficult circuit environments PIDG Terminals consist of tin plated copper or tin plated phosphor bronze body for spring spades with a copper sleeve and insulation sleeve fitted over terminal barrel Design of the tool dies and construction of the terminal allows for uniform insulation thickness under crimping pressure, transmitting this pressure evenly to the center of the crimp area The AMP Mated Tool/Terminal Concept AMP compression crimping produces crimps for a given size wire and terminal that are alike in appearance and performance Terminal and crimping tool are designed as uniform matched devices Dies are precisionengineered from the finest hard-metal alloys Crimping pressure is controlled by a ratchet device on the hand tool or a corresponding pre-calibration in the crimping jaws of AMP automated crimping machines The Crimp When done properly, crimping pressure can neither overstress nor under stress the terminal barrel machined dies fully bottom to the precise crimp height Resulting termination is free of contamination Resistant to shock and critical environments Tensile strength approaches that of the wire itself PIDG Terminals meet or exceed the requirements of MIL-T-7928, Type II, Class 1 and 2 Refer to AMP Qualified Products for Military Application, Catalog 73-159 for Military Specification Number to AMP Part Number cross reference Color Coding. Terminal insulation is color-coded by wire range to prevent errors during installation. Serrations. Serrations inside barrel provide maximum contact and tensile strength after crimping. Nylon. Nylon sleeve has high dielectric strength. Temperature Rating: 5 C Max. AMP PIDG Terminals (Use PIDG Tooling) AMP LR7189 Wire Certified Range 22-1 22-1 Solid or Stranded 1-14 1-14 Solid or Stranded 300 V Max., 5 C. Max. 1 12-12- Solid or Stranded Note: 22-1 terminals are stamped 22-18 in accordance with MIL-T-7928. 1 UL & CSA Nylon Basic Terminal. The basic terminal is constructed of fine grade high conductivity copper per ASTM B-152 and tin-plated per ASTM B-545. Basic material for Spring Spade Tongue Terminals is phosphor bronze per ASTM B-139 and tin-plated per ASTM B-545. Tyco Electronics' special plating process creates durable corrosion resistance to salt spray and most chemical fumes. Copper Sleeve. The specially designed copper sleeve, fitted over the terminal barrel, provides circumferential insulation support to the wire and allows the wire to be bent in any direction, without fraying the wire s insulation or breaking the conductor. Funnel Ramp Entry. Prevents a turned back strand and permits rapid wire insertion during high speed production. Note: Over size expansions are provided in vinyl insulation only. AMP PIDG Nylon Butt Window Splice (Use PIDG Tooling) AMP LR7189 Wire Certified Range 22-1 22-1 Stranded or Solid 1-14 1-14 Stranded or Solid 300 V Max., 5 C. Max. 12-12- Stranded or Solid Note: 22-1 splices are stamped 22-18 in accordance with MIL-T-7928. PIDG Terminals and Splices 7

PIDG Terminals and Splices (Continued) Ring Tongue Terminals L E W C -Nylon, UL 94V-2 Terminal Body and Metallic Sleeve-Copper per ASTM B-152 Plating-Tin per ASTM B-545 Application Tooling -pg. PIDG Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted 2.203.211.32.739.5 M2 5.1 5.3 1.05 18.77 2.7 543-1 4.203 5.1.211 5.3.32 1.05.73 18.9.5 2.7 52189 2-24.029.243.4.792.5 238-475 0.74 M3.5.17 1.87 20.12 2.7 53073 [0.12-0.24] 8.71.814.5 M4 17.04 20.8 2.7 54311-1.702 17.83.88 22.05.5 2.7 54312-1 54312-2 0.121 3.07.452 11.48.525 13.34.082 2.08 3213.121 3.07.452 11.48.525 13.34.082 2.08 323912* 2-323912-1 2.211.542.15.082 5.3 13.77 15.2 2.08 329951* M2.15.211.542.17 /Br..082 4.19 5.3 13.77 15.7 2.08 32120* 1-32120-0.203 5.1.211 5.3.542 13.77.4 1.41.082 2.08 323913 2-323913-1 4.203 5.1.211 5.3.542 13.77.4 1.41.082 2.08 323914* 2-323914-1 2-22.020.198.308.43.745.082 202-8 0.51 5.03 7.82 1.33 18.92 2.08 32117 [0.-0.41].203.211.542.4.082 M3.5 5.1 5.3 13.77 1.41 2.08 323915* 2-323915-2.12 15.54.740 18.80.082 2.08 32875* 2-32875-1 8.12.740.082 15.54 18.80 2.08 32391* 2-32391-1 M4.300.12.75.082 7.2 15.54 19.43 2.08 52124 52124-2.12 15.54.740 18.80.082 2.08 324075* 2-324075-1.300 7.2.12 15.54.75 19.43.082 2.08 52124-1 0.10 4.0.50 12.85.589 14.9 Natural.0 2.54 2-328489-1 2 M2.10 4.0.50 12.85.589 14.9 Natural.0 2.54 3293 2-3293-1.203.31.735 Natural.0 5.1 1.03 18.7 2.54 50534 24-20 4.025.31.774 Natural.0 320-1,290 0.4 1.03 19. 2.54 323985 [0.1-0.5].31.774 Natural.0 M3.5 1.03 19. 2.54 32398 2-32398-1 8 M4.2 1.81.821 20.85 Natural.0 2.54 323989 1-323989-0.2 1.81.821 20.85 Natural.0 2.54 323990 2-323990-1 Note: C dimension applies from edge of metal wire barrel to center of stud hole. Must be crimped with 22-18 or 22-1 PIDG (red) Tooling. 8

PIDG Terminals and Splices (Continued) Ring Tongue Terminals (Continued) Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted 1.10.15.50.43 4.0 3.9 14.22 1.33 327174 2-327174-1.182 4.2.172 4.37.57 14.3.9 1.99 324158 2-324158-1 2 M2.182 4.2.172 4.37.57 14.3.9 1.99 320773.218 5.54.15 3.9.50 14.22.72 17.07 32857* 2-32857-1.182 4.2.172 4.37.57 14.3.9 1.99 /Green 32754*.182 4.2.172 4.37.57 14.3.9 1.99 320882* 2-320882-1.218.15.50.72 5.54 3.9 14.22 17.07 320553* 2-320553-2 4.218 5.54.15 3.9.50 14.22.72 17.07 3254 1.218 5.54.15 3.9.50 14.22.72 17.07 31880* 2-31880-1.218 5.54.15 3.9.50 14.22.72 17.07 Black 35229.71 18.19.844 21.44 323758 2-323758-1.71 18.19.844 21.44 33048 2-33048-1.218 5.54.15 3.9.50 14.22.72 17.07 3149* 2-3149-2.218 5.54.15 3.9.50 14.22.72 17.07 3150* 2-3150-1 22-1.54.782 5183* 5183-1 509-3,20.033 1.1 19.8 [0.2-1.5] 0.84.54.797 M3.5 1.1 20.24 3151* 2-3151-2.54 1.1.797 20.24 3152* 2-3152-1.85 17.40.844 21.44 323008 2-323008-1.85 17.40.844 21.44 32878 2-32878-1.54 1.1.797 20.24 320554* 2-320554-1.54 1.1.797 20.24 3188* 2-3188-2 8 M4.85 17.40.844 21.44 320551* 1-320551-1.85 17.40.844 21.44 31890* 2-31890-1.344 8.74.297 7.54.701 17.81.87 22.25 32835 2-32835-2.54 1.1.797 20.24 320552* 2-320552-1.54 1.1.797 20.24 31887* 2-31887-1.85 17.40.844 21.44 3153* 2-3153-2.85 17.40.844 21.44 3154* 2-3154-2.344 8.74.297 7.54.701 17.81.87 22.25 3283*.344 8.74.297 7.54.701 17.81.87 22.25 32837* 32837-1 1 Slightly larger than standard #4 stud hole. (.128 in./3.25 mm.) PIDG Terminals and Splices Note: C dimension applies from edge of metal wire barrel to center of stud hole. 9

PIDG Terminals and Splices (Continued) Ring Tongue Terminals (Continued) L E W C -Nylon, UL 94V-2 Terminal Body and Metallic Sleeve-Copper per ASTM B-152 Plating-Tin per ASTM B-545 Application Tooling-pg. PIDG Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted.49 11.91.437 11..841 21.3 1.078 27.38 320571* 2-320571-2 1/4 M.49 11.91.437 11..841 21.3 1.078 27.38 Black 5593-1 5593-2.49 11.91.437 11..841 21.3 1.078 27.38 31894* 2-31894-2.49.437.841 1.078 11.91 11. 21.3 27.38 320572* 2-320572-1 5/1.49.437.841 1.078 22-1 31895* 2-31895-1 509-3,20.033 M8 11.91 11. 21.3 27.38 [0.2-1.5] 0.84.531.54.950 1.218 13.49 13.87 24.13 30.94 324123.531 13.49.54 13.87.950 24.13 1.218 30.94 320573* 2-320573-4 3/8.531 13.49.54 13.87.950 24.13 1.218 30.94 31897* 2-31897-2.5 1..437 11..841 21.3 1.171 29.74 321522 1/2 M12.713 18.11.530 13.4.934 23.72 1.293 32.84 328975* 20-1HD 1 992-2,800.042.49.718.955.150 [0.50-1.42] 1.07 11.91 18.24 24.2 3.81 150247 2 M2.180 4.57.171 4.34.575 14.1.8 1.97 324993.171 4.34.575 14.1.703 17.8.150 3.81 324159* 2-324159-2 4.171 4.34.575 14.1.703 17.8 32899* 2-32899-1.85 17.40.813 20.5.150 3.81 3237.171 4.34.575 14.1.703 17.8.150 3.81 32051* 2-32051-2.171 4.34.575 14.1.703 17.8 32019* 2-32019-1.85 17.40.813 20.5 50881 50881-2 1-14.033.54.813 0.84 M3.5 1.1 20.5 32882* 2-32882-1.85.844.150 17.40 21.44 3.81 5184* 5184-3.343 8.71.85 17.40.859 21.82.150 3.81 3157* 2-3157-2.343 8.71.85 17.40.859 21.82 3158* 2-3158-1.54 1.1.813 20.5 53941-1* 53941-2 8.85.844.150 17.40 21.44 3.81 5184-1* 5184-5 M4.343.85.859.150 8.71 17.40 21.82 3.81 32050* 2-32050-1.343.85.859 8.71 17.40 21.82 32055* 2-32055-1 1 Heavy duty for extra mechanical strength. Note: C dimension applies from edge of metal wire barrel to center of stud hole.

PIDG Terminals and Splices (Continued) Ring Tongue Terminals (Continued) Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted.54 1.1.813 20.5 53942-1 53942-2.85 17.40.844 21.44.150 3.81 5184-2* 5184-4.343 8.71.85 17.40.859 21.82.150 3.81 320574* 2-320574-2.343 8.71.85 17.40.859 21.82 310* 2-310-1.49 11.91.437 11..841 21.3 1.078 27.38 324533 2-324533-2 12.49 11.91.437 11..841 21.3 1.078 27.38 32408 2-32408-1 14.48.71.953 11.89 18.19 24.21 35274.49.437.841 1.078 1-14.150 32053* 2-32053-2.033 11.91 11. 21.3 27.38 3.81 0.84 1/4.49.437.841 1.078 M 11.91 11. 21.3 27.38 3245* 2-3245-1.49 11.91.437 11..841 21.3 1.078 27.38 Black 325034 2-325034-1 5/1.49.437.841 1.078.150 11.91 11. 21.3 27.38 3.81 320575* 2-320575-1 M8.49.437.841 1.078 11.91 11. 21.3 27.38 328998* 2-328998-1 3/8.531 13.49.54 13.87.950 24.13 1.218 30.94.150 3.81 32054* 2-32054-3.531 13.49.54 13.87.950 24.13 1.218 30.94 328999* 2-328999-1 1/2.713.530.934 1.293.150 18.11 13.4 23.72 32.84 3.81 32897 M12.713.530.934 1.293 18.11 13.4 23.72 32.84 328849* 4.219 5.5.8 20.57.953 24.21 /Blk. 5.84 33734.219 5.5.8 20.57.953 24.21 /Blk. 5.84 32031* 2-32031-1 M3.5.219 5.5.8 20.57.953 24.21 /Blk. 3534*.343 8.71.872 22.15 1.04 2.57 /Blk. 5.84 33724 8.343.872 1.04 /Blk. 8.71 22.15 2.57 5.84 32027* 1-32027-0 M4.343.872 1.04 /Blk. 8.71 22.15 2.57 35* 2-35-1.343 8.71.872 22.15 1.04 2.57 /Blk. 5.84 32030* 2-32030-2 1-14HD 1.050.343.872 1.04 /Blk. 1.27 8.71 22.15 2.57 34805* 2-34805-1.500.344 1.179 1.432 /Blk..220 12.70 8.74 29.95 3.37 5.59 329391.500 12.70.344 8.74.935 23.75 1.188 30.18 /Blk. 5.84 34974* 2-34974-1.500 12.70.344 8.74.935 23.75 1.188 30.18 /Blk. 32382 2-32382-1 1/4 M.531 13.49.437 11. 1.028 2.11 1.29 32.92 /Blk. 5.84 327743 1-327743-1.531 13.49.437 11. 1.028 2.11 1.29 32.92 /Blk. 3480* 2-3480-3.531 13.49.437 11. 1.028 2.11 1.29 32.92 2-3480-2 5/1 M8.531 13.49.437 11. 1.028 2.11 1.29 32.92 /Blk. 348 1-348-1 1 Heavy duty for extra mechanical strength. PIDG Terminals and Splices Note: C dimension applies from edge of metal wire barrel to center of stud hole. 11

PIDG Terminals and Splices (Continued) Ring Tongue Terminals (Continued) L E W C -Nylon, UL 94V-2 Terminal Body and Metallic Sleeve -Copper per ASTM B-152 Plating-Tin per ASTM B-545 except where noted. Application Tooling-pg. PIDG Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted 3/8.531 13.49.437 11. 1.028 2.11 1.29 32.92 /Blk. 5.84 33089 1-14HD 1.750.25 1.21 1.594 /Blk. 3531*.050 1/2 19.05 15.88 30.89 40.49 1.27 M12 1 1.000 1.591 2.219 /Blk. 31.75 25.40 40.41 5.3 3203 3/4 1 1.000 1.591 2.219 /Blk. 31.75 25.40 40.41 5.3 322724 4.219 5.5.8 20.57.953 24.21 35148* 1-35148-1.219 5.5.8 20.57.953 24.21 5.84 32034* 2-32034-1.219 5.5.8 20.57.953 24.21 35149* 2-35149-1 M3.5.302 7.7.893 22.8 1.052 2.72 5.84 3288 3288-1.375 9.53.302 7.7.893 22.8 1.083 27.51 5.84 32057* 2-32057-2.375 9.53.302 7.7.893 22.8 1.083 27.51 357* 2-357-1.872 22.15 1.031 2.19 5.84 35787* 1-35787-0 8.302.893 1.052 7.7 22.8 2.72 5.84 324915* M4.375.302.893 1.083 9.53 7.7 22.8 27.51 5.84 32058* 2-32058-1.375.302.893 1.083 12-358* 2-358-1.042 9.53 7.7 22.8 27.51 5,180-13,0 1.07 [2.2-.4].302.893 1.052 7.7 22.8 2.72 5.84 324918* 1-324918-0.343 8.71.872 22.15 1.04 2.57 5.84 32883* 1-32883-0.375 9.53.302 7.7.893 22.8 1.083 27.51 5.84 311* 2-311-2.375 9.53.302 7.7.893 22.8 1.083 27.51 359* 2-359-1.500 12.70.344 8.74.935 23.75 1.188 30.18 5.84 2-32372-1 2-32372-3.500 12.70.344 8.74 1.179 29.95 1.432 3.37.220 5.59 329389.500 12.70.344 8.74.935 23.75 1.188 30.18 5.84 35273* 2-35273-2 1/4 M.531 13.49.48 11.89 1.054 2.77 1.322 33.58 5.84 32059* 2-32059-3.531 13.49.48 11.89 1.054 2.77 1.322 33.58 5.84 2-32545-4 2.531 13.49.48 11.89 1.054 2.77 1.322 33.58 351* 2-351-1 1 Heavy duty for extra mechanical strength. 2 Terminal body plating Gold per MIL-G-45204 Type II over Nickel per QQ-N-290. 3 Terminal body plating Nickel per QQ-N-290. Note: C dimension applies from edge of metal wire barrel to center of stud hole. 12

PIDG Terminals and Splices (Continued) Ring Tongue Terminals (Continued) Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted M5.375 9.53.302 7.7.97 24.5 1.10 29.4.300 7.2 55157-2 5/1.531.48 1.054 1.322 13.49 11.89 2.77 33.58 5.84 32057* 2-32057-1 M8.531.48 1.054 1.322 13.49 11.89 2.77 33.58 35111* 2-35111-1.593 15.0.531 13.49 1.115 28.32 1.414 35.92 5.84 320577* 2-320577-3 3/8.593 15.0.531 13.49 1.115 28.32 1.414 35.92 35112* 12-.042.750.25 1.21 1.594 5,180-13,0 35150 1.07 19.05 15.88 30.89 40.49 [2.2-.4].715.474 1.05 1.414 18.1 12.04 27.05 35.92 5.84 52077 1/2.715.50 1.151 1.511 18.1 14.22 29.24 38.38 5.84 33147 M12.750.25 1.21 1.594 19.05 15.88 30.89 40.49 5.84 323784.750 19.05.25 15.88 1.21 30.89 1.594 40.49 35151* 5/8 M1 1 31.75 1.000 25.40 1.591 40.41 2.219 5.3 5.84 32415 Note: C dimension applies from edge of metal wire barrel to center of stud hole. Vinyl insulation material PIDG Terminals and Splices 13

PIDG Terminals and Splices (Continued) Ring Tongue Terminals (Vinyl) L E W C -Vinyl, UL 94V-0 Terminal Body and Metallic Sleeve-Copper per ASTM B-152 Plating-Tin per ASTM B-545 except where noted. PIDG Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted M3.5.54 1.1.797 20.24 31885.85.844 31888 8 17.40 21.44 22-1 509-3,20.033 M4.85.844 2-31888-1 2 [0.2-1.5] 0.84 17.40 21.44.54 1.1.797 20.24 31884.85 17.40.844 21.44 31891.54 1.1.813 20.5 2-322238-1 1-14.033.85.844.150 0.84 17.40 21.44 3.81 5181-4.343.85.859 8.71 17.40 21.82 31903.343.91 1.135 /Blk..300 8.71 24.41 28.83 7.2 3533* 1-14HD 1/4.531.437 1.117 1.385 1 /Blk..300 3532*.050 M 13.49 11. 28.37 35.18 7.2 1.27 5/1.531.437 1.117 1.385 /Blk..300 M8 13.49 11. 28.37 35.18 7.2 35538 1/2 M12 1 31.75 1.000 25.40 1.80 42.7 2.308 58.2 /Blk..300 7.2 3485 M3.5.375 9.53.302 7.7.982 24.94 1.172 29.77.300 7.2 3504 8 M4.375 9.53.302 7.7.982 24.94 1.172 29.77.300 7.2 3505* 2-3505-2.375 9.53.302 7.7.982 24.94 1.172 29.77.300 7.2 3534* 2-3534-1 12-5mm 3.375.302.97 1.10.300 55157-2 5,180-13,0.042 9.53 7.7 24.5 29.4 7.2 1.07 [2.2-.4].500.344 1.024 1.277.300 32373 2-32373-2 1/4 12.70 8.74 2.01 32.44 7.2 M.531.48 1.148 1.41.300 13.49 11.89 29.1 35.97 7.2 35345* 2-35345-1 5/1 M8.531 13.49.48 11.89 1.148 29.1 1.41 35.97.300 7.2 3534* 2-3534-1 3/8.593 15.0.531 13.49 1.211 30.7 1.5 38.35.300 7.2 35478 1-35478-0 1 Heavy duty for extra mechanical strength. 2 Terminal body plating Gold per MIL-G-45204 Type II over Nickel per QQ-N-290. 3 # stud may be substituted. Note: C dimension applies from edge of metal wire barrel to center of stud hole. 14

PIDG Terminals and Splices (Continued) Ring Tongue Terminals ( Restricting) [mm 2 ] L E W C -Nylon, UL 94V-2 Terminal Body-Copper per ASTM B-152 Plating-Tin per ASTM B-545 Metallic Sleeve-Copper per ASTM B-152 Plating-Nickel per QQ-N-290 or Tin per ASTM B-545 Application Tooling-pg. Tongue Dimensions Terminal Wire Part Numbers Stud W C E L Loose Tape Thickness Size Color Diameter Min. Max. Max. Piece Mounted Max. Solid/Stripe Range 2 M2.203 5.1.211 5.3.32 1.05.739 18.77 /Black.02-.055 0.-1.40 4.203.211.32.73 /Black.02-.055 5.1 5.3 1.05 18.9 0.-1.40 2 304.029.243.4.792 /Black.02-.055 [0.15] 0.74 M3.5.17 1.87 20.12 0.-1.40 8 M4.71 17.04.814 20.8 /Black.02-.055 0.-1.40.702 17.83.83 21.92 /Black.02-.055 0.-1.40 4.203 5.1.211 5.3.587 14.91.91 17.55 /.031-.055 0.79-1.40.020.57.785 /.031-.055 M3.5 1.9 19.94 0.79-1.40 0.51 8.57.785 /.031-.055 M4 1.9 19.94 0.79-1.40.57 1.9.785 19.94 /.031-.055 0.79-1.40 24 2.203.211.32.739 475 /.031-.055 M2 5.1 5.3 1.05 18.77 0.79-1.40 [0.24] 4.203.211.32.73 /.031-.055 5.1 5.3 1.05 18.9 0.79-1.40.029 0.74 M3.5.243.17.4 1.87.792 20.12 /.031-.055 0.79-1.40 8 M4.71 17.04.814 20.8 /.031-.055 0.79-1.40.702 17.83.80 21.84 /.031-.055 0.79-1.40 2 M2.182 4.2.172 4.37.38 1.21.731 18.57 /Green.038-.1 0.97-2.79 4.218 5.54.15 3.9.22 15.80.734 18.4 /Green.038-.1 0.97-2.79.218.15.22.734 /Green.038-.1 5.54 3.9 15.80 18.4 0.97-2.79 M3.5.71.844 /Green.038-.1 18.19 21.44 0.97-2.79 8.747.90 /Green.038-.1 22.033 M4 18.97 23.01 0.97-2.79 754 [0.38] 0.84.747.90 /Green.038-.1 18.97 23.01 0.97-2.79 1/4 M.49 11.91.437 11..903 22.94 1 28.9 /Green.038-.1 0.97-2.79 5/1 M8.49 11.91.437 11..903 22.94 1 28.9 /Green.038-.1 0.97-2.79 3/8.531 13.49.54 13.87 1.012 25.70 1.280 32.51 /Green.038-.1 0.97-2.79 1/2 M12.713 18.11.530 13.4.99 25.30 1.355 34.42 /Green.038-.1 0.97-2.79 Note: C dimension applies from edge of metal wire barrel to center of stud hole. Must be crimped with 22-18 or 22-1 PIDG (red) Tooling. 53078 53049 53050 53051 53052 2-323914-2 2-32875-4 2-32391-3 2-32875-5 53053 53054 53055 53055-1 5305 53057 53057-1 52307 52273* 2-3149-3* 5183-2* 5183-5 1-320551-2* 1-320551-5 2-3153-3* 2-3153- 2-320571-3 2-320572-2 2-320573-1 2-328975-1 PIDG Terminals and Splices 15

PIDG Terminals and Splices (Continued) PIDG Terminals and Splices 1 Ring Tongue Terminals ( Restricting) (Continued) [mm 2 ] L E W C Tongue Dimensions Terminal Wire Part Numbers Stud W C E L Loose Tape Thickness Size Color Diameter Min. Max. Max. Piece Mounted Max. Solid/Stripe Range 2 M2.182 4.2.172 4.37.38 1.21.731 18.57 /.04-.1 1.17-2.79 4.218 5.54.15 3.9.22 15.80.734 18.4 /.04-.1 1.17-2.79.218.15.22.734 /.04-.1 5.54 3.9 15.80 18.4 1.17-2.79 M3.5.71.844 /.04-.1 18.19 21.44 1.17-2.79 8.747.90 /.04-.1 20.033 M4 18.97 23.01 1.17-2.79 1,18 [0.0] 0.84.747.90 /.04-.1 18.97 23.01 1.17-2.79 1/4 M.49 11.91.437 11..903 22.94 1 28.9 /.04-.1 1.17-2.79 5/1 M8.49 11.91.437 11..903 22.94 1 28.9 /.04-.1 1.17-2.79 3/8.531 13.49.54 13.87 1.012 25.70 1.280 32.51 /.04-.1 1.17-2.79 1/2 M12.713 18.11.530 13.4.99 25.30 1.355 34.42 /.04-.1 1.17-2.79 4.218 5.54.15 3.9.22 15.80.734 18.4 /White.05-.1 1.42-2.79.218.15.22.734 /White.05-.1 5.54 3.9 15.80 18.4 1.42-2.79 M3.5.71.844 /White.05-.1 18.19 21.44 1.42-2.79 8 M4.747 18.97.90 23.01 /White.05-.1 1.42-2.79 18.033.747.90 /White.05-.1 1,900 0.84 18.97 23.01 1.42-2.79 [0.9] 1/4.49.437.903 1 /White.05-.1 M 11.91 11. 22.94 28.9 1.42-2.79 5/1 M8.49 11.91.437 11..903 22.94 1 28.9 /White.05-.1 1.42-2.79 3/8.531 13.49.54 13.87 1.012 25.70 1.280 32.51 /White.05-.1 1.42-2.79 1/2 M12.713 18.11.530 13.4.99 25.30 1.355 34.42 /White.05-.1 1.42-2.79 4.171 4.34.37 1.18.75 19.43 /.03-.130 1.0-3.30.171.37.75 /.03-.130 4.34 1.18 19.43 1.0-3.30 M3.5.747.90 /.03-.130 18.97 23.01 1.0-3.30 8 M4.747 18.97.90 23.01 /.03-.130 1.0-3.30 1.033.747.90 /.03-.130 2,800 0.84 18.97 23.01 1.0-3.30 [1.42] 1/4.49.437.903 1 /.03-.130 M 11.91 11. 22.94 28.9 1.0-3.30 5/1 M8.49 11.91.437 11..903 22.94 1 28.9 /.03-.130 1.0-3.30 3/8.531 13.49.54 13.87 1.012 25.70 1.280 32.51 /.03-.130 1.0-3.30 1/2 M12.713 18.11.530 13.4.99 25.30 1.355 34.42 /.03-.130 1.0-3.30 Note: C dimension applies from edge of metal wire barrel to center of stud hole. -Nylon, UL 94V-2 Terminal Body-Copper per ASTM B-152 Plating-Tin per ASTM B-545 Metallic Sleeve-Copper per ASTM B-152 Plating-Nickel per QQ-N-290 or Tin per ASTM B-545 Application Tooling-pg. 52307-1 52273-1* 2-3149-4* 5183-3 5183-1-320551-3* 1-320551-7 2-3153-4* 2-320571-4 2-320572-3 2-320573-2 2-328975-2 52273-2* 2-3149-5* 5183-4* 5183-7 1-320551-4* 1-320551-8 2-3153-5* 2-3153-9 2-320571-5 2-320572-4 2-320574-7 2-320573-3 2-328975-3 52274 2-32051-3* 2-32051-5 5184-* 1-5184-2 1-5184-0* 1-5184- 5184-7* 2-32053-3 2-320575-2 2-32054-1 2-32897-1

PIDG Terminals and Splices (Continued) Ring Tongue Terminals ( Restricting) (Continued) Tongue Dimensions Terminal Wire Part Numbers Stud W C E L Loose Tape [mm 2 ] Thickness Size Color Diameter Min. Max. Max. Piece Mounted Max. Solid/Stripe Range 4.171 4.34.37 1.18.75 19.43 /Green.078-.130 1.98-3.30 52274-1.171.37.75 /Green.078-.130 4.34 1.18 19.43 1.98-3.30 2-32051-4 M3.5.747.90 /Green.078-.130 18.97 23.01 1.98-3.30 5184-8* 1-5184-4 8 M4.747 18.97.90 23.01 /Green.078-.130 1.98-3.30 1-5184-1* 1-5184-7 14.033.747.90 /Green.078-.130 4,234 0.84 18.97 23.01 1.98-3.30 5184-9* 1-5184-5 [2.15] 1/4.49.437.903 1 /Green.078-.130 M 11.91 11. 22.94 28.9 1.98-3.30 2-32053-4 5/1 M8.49 11.91.437 11..903 22.94 1 28.9 /Green.078-.130 1.98-3.30 2-320575-3 3/8.531 13.49.54 13.87 1.012 25.70 1.280 32.51 /Green.078-.130 1.98-3.30 2-32054-2 1/2 M12.713 18.11.530 13.4.99 25.30 1.355 34.42 /Green.078-.130 1.98-3.30 2-32897-2 M3.5.375 9.53.302 7.7.958 24.33 1.148 29.1 /.095-.200 2.41-5.08 2-311-5 8.375.302.958 1.148 /.095-.200 M4 9.53 7.7 24.33 29.1 2.41-5.08 2-32058-2*.375 9.53.302 7.7.958 24.33 1.148 29.1 /.095-.200 2.41-5.08 2-311-3* 12.042 1/4.531.48 1.124 1.392 /.095-.200,54 1.07 M 13.49 11.89 28.55 35.3 2.41-5.08 2-32059-5 [3.37] 5/1.531.48 1.124 1.392 /.095-.200 M8 13.49 11.89 28.55 35.3 2.41-5.08 2-32057-2 3/8.593 15.0.531 13.49 1.187 30.15 1.48 37.74 /.095-.200 2.41-5.08 2-320577-1 1/2 M12.715 18.1.474 12.04 1.130 28.70 1.490 37.85 /.095-.200 2.41-5.08 52077-1 M3.5.375 9.53.302 7.7.958 24.33 1.148 29.1 /Brown.119-.200 3.02-5.08 2-311- 3-311-0 8 M4.375 9.53.302 7.7.958 24.33 1.148 29.1 /Brown.119-.200 3.02-5.08 2-32058-3*.375 9.53.302 7.7.958 24.33 1.148 29.1 /Brown.119-.200 3.02-5.08 2-311-4 2-311-8.042 1/4.531.48 1.124 1.392 /Brown.119-.200 12,0 1.07 M 13.49 11.89 28.55 35.3 3.02-5.08 2-32059- 2-32059-8 [.11] 5/1.531.48 1.124 1.392 /Brown.119-.200 M8 13.49 11.89 28.55 35.3 3.02-5.08 2-32057-3 3/8.593 15.0.531 13.49 1.187 30.15 1.48 37.74 /Brown.119-.200 3.02-5.08 2-320577-2 1/2 M12.715 18.1.474 12.04 1.130 28.70 1.490 37.85 /Brown.119-.200 3.02-5.08 52077-2 Note: C dimension applies from edge of metal wire barrel to center of stud hole. PIDG Terminals and Splices 17

Ring Tongue Terminals 90 Bend PIDG Terminals and Splices (Continued) -Vinyl, UL 94V-0 Terminal Body and Metallic Sleeve-Copper per ASTM B-152 Plating-Tin per ASTM B-545 Application Tooling-pg. PIDG Terminals and Splices Tongue Dimensions Wire Part Number Stud Terminal Cicular Mils Thickness Size W D Diameter Loose [mm 2 ] Max. Min. Color Max. Piece Vinyl 22-1 509-3,20.033.157 [0.2-1.5] 0.84 3.99 55148-1 Nylon 12-5,180-13,0.040.375.20 [2.2-.4] 1.02 9.53 5.23 9020-1 18

Rectangular Tongue Terminals PIDG Terminals and Splices (Continued) -Nylon except where noted. Terminal Body and Metallic Sleeve -Copper per ASTM B-152 except where noted. Application Tooling-pg. Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L X Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted 2.182.211.542.47.0 2-22.082 32120 2.020 M2 4.2 5.3 13.77 1.43 2.54 2.08 202-8 0.51 [0.-0.41].277.308.43.783.130.082 M3.5 7.04 7.82 1.33 19.89 3.30 2.08 330250 2 M2.182 4.2.203 5.1.07 15.42.727 18.47.115 2.92 325148 4.237.237.43.79.143.02.02 1.33 20.22 3.3 2-32798-1.237.404.8 1.015.195.02.2 20.57 25.78 4.95 32792 5.187.591.73 4.75 15.01 18.9 55777-1 M3.277.277.702.855.143 7.04 7.04 17.83 21.72 3.3 2-327950-1.237.404.8 1.015.195 22-1 2-32795-1.033.02.2 20.57 25.78 4.95 509-3,20 [0.2-1.5] 0.84.71.84 32029 2-32029-1 18.19 21.49 M3.5.71.84 18.19 21.49 3347* 2-3347-1.302 7.7.45 11.81.872 22.15 1.9 28.17.227 5.77 2-327938-1 2-327938-2 8.302.45.872 1.9.227 7.7 11.81 22.15 28.17 5.77 327944* 2-327944-2 M4.390.21 1.039 1.359.3 9.91 15.77 2.39 34.52 7.87 327932.85 17.40.893 22.8.203 5.1 320209*.237.237.43.79.143.150.02.02 1.33 20.22 3.3 3.81 2-327970-4 4.237.404.8 1.015.195 1-14.150 2-32794-4.033.02.2 20.57 25.78 4.95 3.81 0.84.244.71.85.150 5594-1 1 5.20 18.19 21.74 3.81 M3.277.277.702.855.143.150 7.04 7.04 17.83 21.72 3.3 3.81 2-327952-2 1 - Vinyl PIDG Terminals and Splices 2 Terminal Body - Brass per MIL-C-50. Note: C dimension applies from edge of metal wire barrel to center of stud hole. 19

Rectangular Tongue Terminals (Continued) PIDG Terminals and Splices (Continued) -Nylon except where noted. Terminal Body and Metallic Sleeve -Copper per ASTM B-152 Application Tooling pg. PIDG Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L X Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted.237.02.404.2.8 20.57 1.015 25.78.195 4.95.150 3.81 2-327958-4.237.02.404.2.8 20.57 1.015 25.78.195 4.95 2-327958-1.244.71.85.150.20 18.19 21.74 3.81 33172 M3.5.244.71.85.20 18.19 21.74 33173*.29 7.52.203 5.1.07 15.42.752 19..150 3.81 3318 1-14.033.302.45.872 1.9.227.150 0.84 7.7 11.81 22.15 28.17 5.77 3.81 2-327940-4.244.71.85.20 18.19 21.74 35279 8.29.343.747.939.187 7.52 8.71 18.97 23.85 4.75 321283* M4.302.45.872 1.9.227.150 7.7 11.81 22.15 28.17 5.77 3.81 2-32794-4.390 9.91.21 15.77 1.039 2.39 1.359 34.52.3 7.87.150 3.81 2-327934-2.85 17.40.940 23.88 32403 4.237.02.237.02.831 21.11.984 24.99.143 3.3 5.84 327972.237.02.404.2.998 25.35 1.203 30.5.195 4.95 5.84 3279 5 M3.277 7.04.277 7.04.889 22.58 1.042 2.47.143 3.3 5.84 327954 2-327954-2.237.02.404.2.998 25.35 1.203 30.5.195 4.95 5.84 2-32790-1 2-32790-2.302.893 1.085.187 12-32997.042 7.7 22.8 27.5 4.75 5.84 5,180-13,0 1.07 M3.5 [2.2-.4].290.218.809.954 34512 7.37 5.54 20.55 24.23 5.84.302 7.7.45 11.81 1.044 2.52 1 32.54.227 5.77 5.84 327942.302 7.7.45 11.81 1.044 2.52 1 32.54.227 5.77 5.84 327948 8 M4.302 7.7.45 11.81 1.077 27.3 1.247 31.7.10 4.0 5.84 33128 2-33128-1.390 9.91.21 15.77 1.211 30.7 1.531 38.89.3 7.87 5.84 32793 Note: C dimension applies from edge of metal wire barrel to center of stud hole. 20

PIDG Terminals and Splices (Continued) Rectangular Tongue Terminals (Continued) -Nylon, UL 94V-2 Terminal Body -Copper per ASTM B-152 Metallic Sleeve -Copper per ASTM B-152 Plating Nickel per QQ-N-290 Application Tooling-pg. Tongue Dimensions Terminal Wire Part Numbers Stud [mm 2 Thickness Size W C E L X Color Diameter Loose ] Max. Min. Max. Max. Solid/Stripe Range Piece 24 475.020.308.83.875.187 /.031-.055 2-3287-2 [0.24] 0.51 M3.5 7.82 17.35 22.23 4.75 0.79-1.40 5.277.277.934 1.087.143 /Brown.119-.200 53912-2.042 M3 7.04 7.04 23.72 27.1 3.3 3.02-5.08 12,0 [.11] 1.07 8.390.21 1.27 1.59.3 /Brown.119-.200 M4 9.91 15.77 32.41 40.54 7.87 3.02-5.08 53914-2 Note: C dimension applies from edge of metal wire barrel to center of stud hole. Spade Tongue Terminals -Nylon, UL 94V-2 Terminal Body and Metallic Sleeve -Copper per ASTM B-152 Application Tooling-pg. PIDG Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L X Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted 2-24 238-475.029.211.32.709.072.095 [0.12-0.24] 0.74 M3.5 5.3 1.05 18.01 1.83 2.41 53115-2 0.078.409.47.02.082 2-22 322001.020 1.98.39 12.09 1.57 2.08 202-8 [0.-0.41] 0.51 4.203.211.542.27.07.082 5.1 5.3 13.77 15.93 1.93 2.08 3235* 2-3235-1 2 M2.182 4.2.203 5.1.07 15.42.727 18.47.115 2.92 328394* 2-328394-1 4.218 5.54.15 3.9.50 14.22.74 17.12.9 2.77 1-327717-0.218 5.54.15 3.9.50 14.22.74 17.12.9 2.77 327717* 1-327717-2.71 18.19.84 21.49 34541* 2-34541-1.297 7.54.203 5.1.07 15.42.753 19.13.141 3.58 34080* 2-34080-1.297.203.07.753.141 22-1 3281* 2-3281-1.033 M3.5 7.54 5.1 15.42 19.13 3.58 509-3,20 [0.2-1.5] 0.84.344.218.22.783.15 8.74 5.54 15.80 19.89 3.9 32403.344 8.74.218 5.54.22 15.80.783 19.89.15 3.9 32404 2-32404-1 8.375.71.908.187 9.53 18.19 23.0 4.75 32050* 2-32050-1 M4.375.71.908.187 9.53 18.19 23.0 4.75 32053* 2-32053-1.375 9.53.71 18.19.908 23.0.187 4.75 32051* 2-32051-1.375 9.53.71 18.19.908 23.0.187 4.75 32054* 2-32054-1 Note: C dimension applies from edge of metal wire barrel to center of stud hole. 21

Spade Tongue Terminals (Continued) PIDG Terminals and Splices (Continued) -Nylon, UL 94V-2 Terminal Body and Metallic Sleeve -Copper per ASTM B-152 Application Tooling-pg. PIDG Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L X Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted.244.20.71 18.19.84 21.49 328281* 1-328281-1 M3.5.297 7.54.203 5.1.07 15.42.753 19.13.141 3.58 35559* 2-35559-1.385.71.908.187 9.78 18.19 23.0 4.75 32058*.297.203.07.753.141 7.54 5.1 15.42 19.13 3.58 321233* 2-321233-1 1-14.033.375.779 1.034 0.84 325199 8 9.53 19.79 2.2 M4.385.71.908.187.150 9.78 18.19 23.0 4.75 3.81 3205* 2-3205-1.385 9.78.71 18.19.908 23.0.187 4.75 32059* 2-32059-1.385 9.78.71 18.19.908 23.0.187 4.75.150 3.81 32057.385 9.78.71 18.19.908 23.0.187 4.75 3200* 2-3200-1.290.218.809.954 7.37 5.54 20.55 24.23 5.84 322985* 1-322985-0 M3.5.29.887 1.095.203 7.52 22.53 27.81 5.1 5.84 32859* 2-32859-1.48 1.059 1.314 12-325197.042 11.89 2.90 33.38 5.84 5,180-13,0 [2.2-.4] 1.07 8.40.29.887 1.095.203 M4.31 7.52 22.53 27.81 5.1 5.84 32588* 2-32588-1.40.31.29 7.52.887 22.53 1.095 27.81.203 5.1 35152* 2-35152-1.40.31.29 7.52.887 22.53 1.095 27.81.203 5.1 5.84 32589* 2-32589-1 Note: C dimension applies from edge of metal wire barrel to center of stud hole. 22

Flanged Spade Tongue Terminals PIDG Terminals and Splices (Continued) -Nylon, UL 94V-2 Terminal Body and Metallic Sleeve -Copper per ASTM B-152 Application Tooling-pg. Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L X H Diameter Loose Tape ] Max. Min. Max. Max. Min. Color Max. Piece Mounted 2 M2.182 4.2.203 5.1.534 1.49 1.48.1 2.79.02 0..082 2.08 324597* 2-324597-1 2-22.020 4.193.203.534.49.1.02.082 202-8 0.51 4.90 5.1 1 1.48 2.79 0. 2.08 5239* 5239-1 [0.-0.41].203.534.49.1.02.082 M3.5 5.1 1 1.48 2.79 0. 2.08 51874* 51874-1 2.182.203.07.727.115.041 4.2 5.1 15.42 18.47 2.92 1.04 2-32408-2 M2.182.203.07.727.115.041 4.2 5.1 15.42 18.47 2.92 1.04 32408* 2-32408-1.203 5.1.07 15.42.737 18.72.04 1.17 322777* 2-322777-1.25.73.203 5.1.07 15.42.737 18.72.04 1.17 32242.29.203.07.737.04 M3.5 7.52 5.1 15.42 18.72 1.17 3251* 2-3251-1 22-1.033.29.203.07.737.04 509-3,20 0.84 7.52 5.1 15.42 18.72 1.17 3252* 2-3252-1 [0.2-1.5].328.203.07.737.04 8.33 5.1 15.42 18.72 1.17 324557 2-324557-1.29 7.52.203 5.1.07 15.42.737 18.72.04 1.17 2-3252-2 2-3252-3 8 M4.41.57.54 1.1.830 21.08.171 4.34.02 1.57 32497 2-32497-1.41.57.54 1.1.830 21.08.171 4.34.02 1.57 32498* 2-32498-1.29 7.52.203 5.1.07 15.42.737 18.72.04 1.17 1-3313-0 1-3313-1.294 7.47.203 5.1.07 15.42.737 18.72.047 1.19.150 3.81 2-32081-2 2-32081-3 M3.5.294 7.47.203 5.1.07 15.42.737 18.72.047 1.19 32081* 2-32081-1.328 8.33.203 5.1.07 15.42.737 18.72.047 1.19 32457* 1-14.033.294.203.07.737.047 0.84 7.47 5.1 15.42 18.72 1.19 32082* 2-32082-1 8.41.54.830.171.02.150 M4.57 1.1 21.08 4.34 1.57 3.81 33155*.41.57.54 1.1.830 21.08.171 4.34.02 1.57 3315 2-3315-1.294 7.47.203 5.1.07 15.42.737 18.72.052 1.19 32083* 2-32083-2.29 7.52.841 21.3 1.017 25.83.171 4.34.052 1.32 5.84 324577 1-324577-0 M3.5.29 7.52.841 21.3 1.017 25.83.171 4.34.052 1.32 325150*.328.841 1.017.171.052 12-324587.042 8.33 21.3 25.83 4.34 1.32 5.84 5,180-13,0 [2.2-.4] 1.07 8.41.841 1.017.171.052 M4.57 21.3 25.83 4.34 1.32 5.84 325* 2-325-1.41.57.841 21.3 1.017 25.83.171 4.34.052 1.32 5.84 3285 2-3285-1.41.57.841 21.3 1.017 25.83.171 4.34.052 1.32 324015* 2-324015-1 Note: C dimension applies from edge of metal wire barrel to center of stud hole. PIDG Terminals and Splices 23

Short Spring Spade Tongue Terminals PIDG Terminals and Splices (Continued) -Nylon, UL 94V-2 Terminal Body -Phosphor Bronze per ASTM B-139 Metallic Sleeve -Copper per ASTM B-152 Application Tooling-pg. PIDG Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L X Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted 2 M2.171 4.34.20 5.23.537 13.4.51 1.54.9 2.77.082 2.08 52921* 52921-1 4.203.219.550.95.082 5.1 5.5 13.97 17.5 2.08 52922* 52922-1 2-22 202-8.020 5.203.534.79.082 0.51 M3 5.1 1 17.25 2.08 52923 52923-1 [0.-0.41].203.534.79.082 M3.5 5.1 1 17.25 2.08 52924* 52924-1 8 M4.375 9.53.12 15.54.787 19.99.082 2.08 52925 52925-1 4.203 5.1.54 1.1.799 20.29 52927* 52927-1 5 M3.54 1.1.799 20.29 52928* 52928-1.54.799 1.1 20.29 52929* 52929-1 M3.5.54.799 1.1 20.29 52929-3.244.725.895 22-1 5578-1.033.20 18.42 22.73 509-3,20 [0.2-1.5] 0.84 8.375.85.80 M4 9.53 17.40 21.84 52930* 52930-1.375 9.53.85 17.40.80 21.84 52930-3.40.31.85 17.40.908 23.0.218 5.54 52931* 52931-1.40.31.85 17.40.908 23.0.218 5.54 52931-3 1/4 M.25 15.88.343 8.71.747 18.97 1.033 2.24 52933* 5 M3.54 1.1.799 20.29 52934* 52934-1.54.799 1.1 20.29 52935* 52935-1 M3.5.54.799.182 1.1 20.29 4.2 52935-2* 52935-3.375.85.80 1-14 5293* 5293-1.033 8 9.53 17.40 21.84 0.84 M4.375.85.80.182 9.53 17.40 21.84 4.2 5293-2 5293-3.40.31.85 17.40.908 23.0.218 5.54 52937* 52937-1.40.31.85 17.40.908 23.0.218 5.54.182 4.2 52937-2* 52937-3 1/4 M.25 15.88.343 8.71.747 18.97 1.033 2.24 52939 5 M3.19 4.29.770 19.5.959 24.3.184 4.7 52940* 52940-1.174.775.959.179 M3.5 4.42 19.9 24.3 4.55 52941* 52941-1 12-5,180-13,0.042 8.375.27.877 1.052 1.07 M4 9.53 7.01 22.28 2.72 52942* 52942-1 [2.2-.4].40.31.27 7.01.877 22.28 1.0 27.94.218 5.54 52943* 52943-1 1/4 M.25 15.88.338 8.59.939 23.85 1.225 31.12 52945* Note: C dimension applies from edge of metal wire barrel to center of stud hole. 24

Long Spring Spade Tongue Terminals PIDG Terminals and Splices (Continued) -Nylon, UL 94V-2 Terminal Body -Phosphor Bronze per ASTM B-139 Metallic Sleeve -Copper per ASTM B-152 Application Tooling-pg. Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L X Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted 2-22 202-8.020.235.5.847.27.082 [0.-0.41] 0.51 M3.5 5.97 14.38 21.51 7.01 2.08 52403 52403-1 4.203 5.1.201 5.11.15 15.2.89 22.7.27 7.01 52408.238.52.933.27 52409* 52409-1.05 1.5 23.70 7.01 22-1.033 M3.5 509-3,20.238.52.933.27 0.84.05 1.5 23.70 7.01 52409-2 52409-3 [0.2-1.5] 8 M4.270.8.84 17.37.979 24.87.290 7.37 524* 524-1.343 8.71.283 7.19.97 17.70 1.005 25.53.303 7.70 52411* 52411-1.238.52.933.27.150.05 1.5 23.70 7.01 3.81 52420* 52420-2 M3.5.238.52.933.27.05 1.5 23.70 7.01 52420-1* 52420-3.270.84.979.290.150 1-14 52421*.033 8.8 17.37 24.87 7.37 3.81 0.84 M4.270.84.979.290.8 17.37 24.87 7.37 52421-1* 52421-3.343 8.71.283 7.19.97 17.70 1.005 25.53.303 7.70 52422-1* 52422-3 1/4 M.437 11..345 8.7.759 19.28 1.2 27.99.338 8.59.150 3.81 52423 52423-2.242.843 1.131.283.15 21.41 28.73 7.19 5.84 52430 52430-2 M3.5.242.843 1.131.283.15 21.41 28.73 7.19 52430-1 52430-3 8.375.273.874 1.174.295 12-52431-1 52431-3.042 M4 9.53.93 22.20 29.82 7.49 5,180-13,0 [2.2-.4] 1.07.375.305.90 1.219.308 9.53 7.75 23.01 30.9 7.82 5.84 52432-2.375.305.90 1.219.308 9.53 7.75 23.01 30.9 7.82 52432-1 52432-3 1/4 M.437 11..345 8.7.94 24.03 1.289 32.74.338 8.59 52433-1 Note: C dimension applies from edge of metal wire barrel to center of stud hole. PIDG Terminals and Splices 25

Slotted Ring Tongue Terminals PIDG Terminals and Splices (Continued) -Nylon except where noted. Terminal Body and Metallic Sleeve -Copper per ASTM B-152 Application Tooling-pg. PIDG Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted 2-22 202-8.020.12.719.082 323011 2-323011-2 [0.-0.41] 0.51 M3.5 15.54 18.2 2.08.85.828 M3.5 17.40 21.03 3521* 2-3521-1 8.54.770 22-1 3954* 2-3954-2.033 M4 1.1 19.5 509-3,20 [0.2-1.5] 0.84.85.812 17.40 20.2 331453 1-331453-0 1/4.49.437.841 1.039 M 11.91 11. 21.3 2.39 321808.343.85.844 1-14 3440.033 M3.5 8.71 17.40 21.44 0.84 8.344.85.837 M4 8.74 17.40 21.2 35440 1-14 HD.048.750.25 1.21 1.594 1.22 3/8 19.05 15.88 30.89 40.49 /Black 9077-2 9077-1.042 1/4.531.48 1.15 1.390 12-.300 1.07 M 13.49 11.89 29.3 35.31 7.2 32111 1 5,180-13,0 [2.2-.4].040 3/8.750.25 1.21 1.594 1.02 19.05 15.88 30.89 40.49 907-2 907-1 1 Vinyl. Note: C dimension applies from edge of metal wire barrel to center of stud hole. Hook Tongue Terminals -Nylon except where noted. Terminal Body and Metallic Sleeve -Copper per ASTM B-152 Application Tooling-pg. 2 [mm 2 ] 22-1 509-3,20 [0.2-1.5] 1-14 1 Vinyl. Tongue Dimensions Wire Part Numbers Stud Terminal Thickness Size W C E L Diameter Loose Tape Max. Min. Max. Max. Color Max. Piece Mounted 0.84.203.07.750 M3.5 5.1 15.42 19.05 34313*.033 8.343.29.705.879 M4 8.71 7.52 17.91 22.33 3245 M3.5.343 8.71.85 17.40.859 21.82.150 3.81 320381 2-320381-1.033 0.84 8 M4.343 8.71.85 17.40.859 21.82 32030* 2-32030-1.343 8.71.85 17.40.859 21.82 35481 1 Note: C dimension applies from edge of metal wire barrel to center of stud hole.

Multiple Stud Terminals PIDG Terminals and Splices (Continued) -Nylon, UL 94V-2 Terminal Body -Copper per ASTM B-152 Metallic Sleeve -Copper per ASTM B-152 Plating -Nickel per QQ-N-290 Application Tooling-pg. Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 Thickness Size W C E L Diameter Loose Tape ] Max. Min. Max. Max. Color Max. Piece Mounted 22-1 509-3,20.033-8-.325.85.957 [0.2-1.5] 0.84 8.2 17.40 24.31 54771-1* 54771-2 12-5,180-13,0.042-8-.325.302.893 1.15 [2.2-.4] 1.07 8.2 7.7 22.8 29.59 5.84 54773-1* Note: C dimension applies from edge of metal wire barrel to center of stud hole. Offset Ring Tongue Terminals -Nylon, UL 94V-2 Terminal Body and Metallic Sleeve -Copper per ASTM B-152 Application Tooling-pg. PIDG Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal Thickness Size W C E L Diameter Loose [mm 2 ] Max. Min. Max. Max. Color Max. Piece.375.71.90 22-1 323039.033 9.53 18.19 23.01 509-3,20 [0.2-1.5] 0.84 M3.5.375.71.90 9.53 18.19 23.01 324011.375.71.90.150 1-14 323817.033 M3.5 9.53 18.19 23.01 3.81 0.84.375.71.90.150 9.53 18.19 23.01 3.81 323818 Note: C dimension applies from edge of metal wire barrel to center of stud hole. 27

Offset Ring Tongue Terminals ( Restricting) PIDG Terminals and Splices (Continued) -Nylon, UL 94V-2 Terminal Body and Metallic Sleeve -Copper per ASTM B-152 Application Tooling-pg. PIDG Terminals and Splices Tongue Dimensions Terminal Wire Part Numbers Stud [mm 2 Thickness Size W C E L Color Diameter Loose ] Max. Min. Max. Max. Solid/Stripe Range Piece 22 754.033.375.758.94 /Green.038-.1 [0.38] 0.84 M3.5 9.53 19.25 24.03 0.97-2.79 52284-4.375.758.94 /.04-.1 20 52284-2.033 M3.5 9.53 19.25 24.03 1.17-2.79 1,18 [0.0] 0.84.375.758.94 /.04-.1 9.53 19.25 24.03 1.17-2.79 52284-3 1 2,800.033.375.748.938 /.03-.130 [1.42] 0.84 M3.5 9.53 19.00 23.83 1.0-3.30 52283-2 14 4,234.033.375.748.938 /Green.078-.130 [2.15] 0.84 9.53 19.00 23.83 1.98-3.30 52283-1 Note: C dimension applies from edge of metal wire barrel to center of stud hole. 28

SHUR-PLUG Terminal PIDG Terminals and Splices (Continued) -Nylon, UL 94V-2 Terminal Body and Metallic Sleeve -Copper per ASTM B-152 Application Tooling-pg. Dimension Terminal Wire Part Numbers L Diameter Loose Tape [mm 2 ] Max. Color Max. Piece Mounted 1-14.790 20.07 324225* 2-324225-1 1-14 Receptacle.78.157 19.51 3.99 15429-1 PIDG Terminals and Splices 3-Way Connector Terminal -Nylon, UL 94V-2 Terminal Body and Metallic Sleeve -Copper per ASTM B-152 Rivet -Brass per QQ-B-2 Application Tooling-pg. Tongue Dimensions Terminal Wire Part Number W L Diameter Loose [mm 2 ] Thickness Max. Max. Max. Color Max. Piece 1-14.033.859 1.370 53222-1* 0.84 21.82 34.80 29

Tabs PIDG Terminals and Splices (Continued) -Nylon, UL 94V-2 Terminal Body and Metallic Sleeve -Copper per ASTM B-152 Application Tooling-pg. PIDG Terminals and Splices Tongue Dimensions Wire Part Numbers Terminal Style Thickness W C L D Diameter Loose [mm 2 ] Max. Min. Max. Color Max. Piece 22-1 509-3,20.033 A.480.904 [0.2-1.5] 0.84 12.19 22.9 34294* 1-14.033 B.15.375.809 0.84 3.9 9.53 20.55 327748 12-5,180-13,0.042 C.225.00 1.194 [2.2-.4] 1.07 5.72 15.24 30.33 5.84 324543* Note: C dimension applies from edge of metal wire barrel to end of tab. 30

PIDG Terminals and Splices (Continued) Butt Splices Sleeve - Standard, Step Down Assembly and Special Nylon Radiation Resistant Polyvinylidene Fluoride (PVF 2 ) Splice Body and Support Sleeve -Copper per ASTM B-152 Application Tooling-pg. Dimension Splice Wire Part Numbers 2 Style L Diameter Loose Tape [mm 2 ] Max. Color Max. Piece Mounted 2-24 3 238-475.890.082 [0.12-0.24] 22.1 2.08 323994 2-323994-1 2-22 202-8.890.082 [0.-0.41] 22.1 2.08 2-323994-2* 24-20 320-1,290 1.035 Natural.0 [0.1-0.5] 2.29 2.54 Standard 323975 2-323975-3 22-1 4 509-3,20 1.25 [0.2-1.5] 32.13 320559* 2-320559-4 1-14 1.25.150 32.13 3.81 32052* 2-32052-3 12-5,180-13,0 1.5.220 [2.2-.4] 42.0 5.59 320570* 2-320570-3 1-14 22-18 to 509-1,900 [0.2-0.9] 1.25 32.13.150/.115 3.81/2.92 327583 2-327583-1 12-22-18 Step Down 5,180-13,0 to 509-1,900 [2.2-.4] [0.2-0.9] Assembly 1.5 42.0.220/ 5.59/ 32739 12-1-14 5,180-13,0 to [2.2-.4] 1.5 42.0.220/ 5.59/ 32738 2-24 3 238-475 Radiation.890 Natural w/.082 [0.12-0.24] Resistant 22.1 Stripes 2.08 5354-1 2-22 202-8 Radiation.890 Natural w/.082 [0.-0.41] Resistant 22.1 Stripes 2.08 5354-3 24-20 320-1,290 1.035 Natural w/.0 [0.1-0.5] 2.29 White Stripes 2.54 Radiation 53547-1 53547-2 22-1 4 Resistant 509-3,20 1.25 Natural w/ [0.2-1.5] 32.13 Stripes 53548-1* 53548-2 1-14 1.25 Natural w/.150 32.13 Stripes 3.81 53549-1* 53549-2 12-5,180-13,0 1.5 Natural w/.220 [2.2-.4] 42.0 Stripes 5.59 53550-1* 12-5,180-13,0 Special 1.245.220 [2.2-.4] 31.2 5.59 32891 5 1 Includes adapter insert. 2 When using two or more wires in either end of a butt splice, the combined cross sectional area must be within the (CMA) circular mil area range listed. 3 2-24 range in accordance with MIL-T-7928. 4 22-1 splices are 22-18 range in accordance with MIL-T-7928. 5 12- butt splice, threaded 8-32 one end. AMP-TAPETRONIC machine tools only. PIDG Terminals and Splices 31

Butt Splice Step Down Adapter Inserts 1 PIDG Terminals and Splices (Continued) Adapter Body -Copper per ASTM B-152 Plating -Zinc Plate/ DyeChromate Application Tooling-pg. PIDG Terminals and Splices Butt Splice Adapter Insert Part No. Dimension Color Part Numbers L Code [mm 2 ] [mm 2 ].350 1-14 22-18 8.89 1-32735-1 32052 509-1,900 [0.2-0.9].402.21 32735* 22-18 509-1,900.52 3273* 12- [0.2-0.9] 14.27 5,180-13,0 320570 [2.2-.4] 1-14.52 32737* 1.04-2.2] 14.27 1Adapter inserts can be ordered separately for use in specific Standard PIDG Butt Splices. Knife Disconnect Splices -Nylon, UL 94V-2 Splice Body and Metallic Sleeve -Copper per ASTM B-152 Application Tooling-pg. Dimensions Splice Wire W L [mm 2 ] Thickness Max. Color Diameter Max..203.878 22-1.031 5.1 22.30 509-3,20 [0.2-1.5] 0.79.203.878 5.1 22.30.203.878.150 1-14.031 5.1 22.30 3.81 0.79.203.878 5.1 22.30 1.234 12-.040 31.34 5.84 5,180-13,0 [2.2-.4] 1.02 1.20 32.00 Part Numbers Loose Piece Tape Mounted 320555* 3244* 2-3244-1 3205* 32448* 32020* 3572* 32

Product Facts Pre-insulated terminal designed for uniformed reliability in most difficult circuit environment Consists of an unplated or tin-plated brass body or a tin-plated phosphor bronze body with a specially designed copper sleeve and insulation sleeve fitted over the terminal barrel Design of the tool dies and construction of the terminal permits uniform insulation thickness under crimping pressure, transmitting this pressure evenly to the center of the crimp area The AMP Mated Tool/Terminal Concept AMP compression crimping produces crimps for a given size wire and terminal that are alike in appearance and performance Terminal and the crimping tool are designed as uniform matched devices Dies are precisionengineered from the finest hard-metal alloys Crimping pressure is controlled by a ratchet device on the hand tool or a corresponding pre-calibration in the crimping jaws of AMP automated crimping machines The Crimp When done properly, crimping pressure can neither overstress nor under stress the terminal barrel machined dies fully bottom to the precise crimp height Resulting termination is free of contamination Resistant to shock and critical environments Tensile strength approaches that of the wire itself PIDG FASTON Terminals and Splices Color Coding. Terminal insulation is color-coded by wire range to prevent errors during installation. Copper Sleeve. The specially designed copper sleeve, fitted over the terminal barrel, provides circumferential insulation support to the wire and allows the wire to be bent in any direction, without fraying the wire s insulation or breaking the conductor. Funnel Ramp Entry. Prevents a turned back strand and rapid wire insertion during high speed production. Temperature Rating: 5 C Max. AMP PIDG FASTON Terminals (Use TETRA-CRIMP Tooling) AMP Component Wire Recognized Range File E 717 22-18 22-18 Stranded LR 7189 Certified 1-14 1-14 Stranded 300 V Max., 5 C. Max. 1 12-12- Stranded 1 UL & CSA Nylon except where noted Nylon. Nylon sleeve has high dielectric strength. Serrations. Serrations inside barrel provide maximum contact and tensile strength after crimping. Basic Terminal. The basic terminal is constructed of fine grade high conductivity brass per ASTM B-3 or phosphor bronze per ASTM B-139. The brass terminal is either unplated or tin-plated per ASTM B-545. The phosphor bronze terminal is tin-plated per ASTM B-545. Tyco Electronics' special plating process creates durable corrosion resistance to salt spray and most chemical fumes. AMP PIDG FASTON Line Splice Connectors 250 Series Component 5 C LR 7189 5 C Recognized Max. Certified Max. File E 717 (Vinyl) (Vinyl) AMP Part No. 00 V AMP Part No. 1-321235-0 Max. 1-321235-0 1-321235-1 1-321235-1 300 V Max. 321235 300 V 321235 300 V 32188 Max. 32188 Max. PIDG FASTON Terminals and Splices 33

PIDG FASTON Terminals and Splices (Continued) Receptacles Receptacle Style: A - No dimple with wire stop B - Dimple with wire stop C - No dimple, no wire stop -Nylon, UL 94V-2 Receptacle Body -Brass per ASTM B-3 or Phosphor Bronze per ASTM B-139 except where noted. Metallic Sleeve -Copper per ASTM B-152 Application Tooling -pg. 7 PIDG FASTON Terminals and Splices 34 Dimensions Terminal Wire Fits Part Numbers Series Style W L Recept. Stock Tab Loose Tape Strip [mm 2 ] Nom. Max. Color Diameter Matl. Thk. Thk. Piece Mounted Form Max..300.900 Brass.018.032 22-18 7.2 22.8 0.4 0.81 40903-1* 40903-2 40902-1 509-1,900 B [0.2-0.9].300.900 Brass.018.032 7.2 22.8 0.4 0.81 5575-1 2 5575-2 2 1-14 B.300.900 Brass.018.032 40905-1* 40905-2 40904-1 7.2 22.8 0.4 0.81.300 1.012 Green Brass.018.032 14-12 7.2 25.70 0.4 0.81 42844-1* 42844-3 0544-3 3,831-,470 1 B [1.94-3.28].300 1.012 Green Phos. Brz..018.032 7.2 25.70 0.4 0.81 42844-2*.300 1.012 Brass.018.032 12-7.2 25.70 0.4 0.81 40907-1* 40907-2 4090-1 5,180-13,0 B [2.2-.4].300 1.012 Phos. Brz..018.032 7.2 25.70 0.4 0.81 1198-2 1198-4 22-18 509-1,900.300.900.145 Brass.01.032 18422-1 18422-2 18421-1 [0.2-0.9] 7.2 22.8 3.8.40.813 Low Insertion 1-14.300.900.173 Brass.01.032 18425-1 18425-2 18424-1 7.2 22.8 4.39.40.813.800.135 Brass.01.020 20.32 3.43 0.41 0.51 9018-1 9018-2.800 Brass.01.020 22-18 20.32 0.41 0.51 40909-1* 40909-2 40908-1 509-1,900 B [0.2-0.9].800 /Black Brass.01.020 20.32 0.41 0.51 40174-1.205.800 Brass.01.032 20.32 0.41 0.81 40911-1* 40911-2 409-1.800 Brass.01.020 1-14 20.32 0.41 0.51 40913-1* 40913-2 B.800 Brass.01.032 20.32 0.41 0.81 40915-1* 40915-2 2-24 238-475 B.700.082 Brass.01.020 41321-1* 41321-2 41320-1 [0.12-0.24] 5.84 17.78 2.08 0.41 0.51.187.800 Brass.01.020 22-18 5.84 20.32 0.41 0.51 40917-1* 40917-2 4091-1 509-1,900 B [0.2-0.9].800 Brass.01.040 5.84 20.32 0.41 1.02 40578-2 Not UL or CSA approved or listed. 1 Wire range is limited as noted. 2 Unplated receptacle body.

PIDG FASTON Terminals and Splices (Continued) Reseptacles (Continued) Dimensions Terminal Wire Fits Part Numbers Series Style W L Recept. Stock Tab Loose Tape Strip [mm 2 ] Nom. Max. Color Diameter Matl. Thk. Thk. Piece Mounted Form Max..800 1-14 Brass.01.020 5.84 20.32 0.41 0.51 40919-1* 40919-2 40918-1.187 B.900 Brass.01.020 5.84 22.8 0.41 0.51 98-1 98-2 22-18 509-1,900.800.145 Brass.01.032 18428-1 18428-2 18427-1.187 [0.2-0.9] 5.84 22.8 3.8.40.813 Low Insertion 1-14.300.900.173 Brass.01.032 184235-1 184235-2 184234-1 7.2 22.8 4.39.40.813.148.734 Natural.1 Brass.012.01 3.7 18.4 2.79 0.30 0.41 48-1* 48-2.148.734.1 22-18 Natural.1 Brass.012.020 3.7 18.4 2.79 0.30 0.51 0-1* 0-2 59-2 Standard 509-1,900 B [0.2-0.9].148.734 Natural.1 Brass.012.032 0894-1* 3.7 18.4 2.79 0.30 0.81 0894-2 0893-2.148.734 Black.1 Brass.012.032 3.7 18.4 2.79 0.30 0.81 178-2 2-24 238-475 A.10.700.082 Brass.01.020 41324-1 41324-2 [0.12-0.24] 4.0 17.78 2.08 0.41 0.51.10.79 Brass.01.012 Standard 4.0 20.22 0.41 0.30 350871-1.10.800 22-18 Brass.01.01 Low 40921-1 40921-2 4.0 20.32 0.41 0.41 509-1,900 A [0.2-0.9].10.800.11 0 Brass.01.020 4.0 20.32 0.41 0.51 40923-1* 40923-2 40922-1.1 Low.10.800 Brass.01.032 4.0 20.32 0.41 0.81 40925-1* 40925-2 40924-1 Insertion A.10.800 Brass.01.020 4.0 20.32 0.41 0.51 40929-1* 40929-2 1-14 A.10.800 Brass.01.032 4.0 20.32 0.41 0.81 40931-1* 40931-2 B.10.800 Brass.01.01 4.0 20.32 0.41 0.41 40927-1 40927-2 C.10.79 Brass.01.032 4.0 20.19 0.41 0.81 41317-1 Not UL or CSA approved or listed. PIDG FASTON Terminals and Splices Receptacles ( Restricting) -Nylon, UL 94V-2 Receptacle Body -Brass per ASTM B-3 Receptacle Style B -Dimple with wire stop Metallic Sleeve -Copper per ASTM B-152 or Nickel per QQ-N-290 Application Tooling -pg. 7 Dimensions Terminal Wire Fits Part Numbers Series Recept. Stock Style W L Tab Loose Tape Strip [mm 2 ] Color Diameter Matl. Thk. Nom. Max. Thk. Piece Mounted Form Solid/Stripe Range.1 22 754 B.148.780 /.040-.080 Brass.012.01 Standard 55319-1 55319-3 [0.38] 3.7 19.81 Green 1.02-2.03 0.30 0.41 35

PIDG FASTON Terminals and Splices (Continued) PIDG FASTON Terminals and Splices Line Splice Connector for 250 Series Terminals Dimensions Plating W L E Unplated Tin 22- Unplated Tin Unplated 1 Oval expansion at end opposite w. (.380 x.320 inside diameter.) 2 E min. on expansion end only. Line Splice Connector for 187 Series Terminals -Vinyl, UL 94V-0 Color -Natural Splice Body -Brass per ASTM B-3 except where noted. Max. Min..391 2.093.80 9.93 53.1 21.84.391 2.093.80 9.93 53.1 21.84.409 2.25 1.151.39.8 29.24.409 2.25 1.151.39.8 29.24.409 2.451.970 2.39 2.2 24.4 Housing -Nylon, UL 94V-2 Splice Body -Brass per ASTM B-3 Part Numbers Loose Piece 321235* 32188 1-321235-0 1-321235-1 1-321235-3 1 Type Single Dual Dual UL File E717 00 V Max Housing Dimensions Temperature Part Numbers Color W L Rating Loose Piece Natural Natural Black.345 1.750 8.7 44.45.50 1.750 1.51 44.45.50 1.750 1.51 44.45 30035-1 5 C 30025-1 150 C 30025-2 3 Receptacle (Low Insertion Force) Dimensions Terminal Wire Fits Part Numbers Series W L Recept. Stock Tab Loose Tape Strip [mm 2 ] Nom. Max. Color Diameter Matl. Thk. Thk. Piece Mounted Form Max. Low 22-18 509-1,900.300.900.145 Brass.01.032 Insertion 18422-1 18422-2 18421-1 [0.2-0.9] 7.2 22.8 3.8.40.813 Low 1-14.300.900.173 Brass.01.032 Insertion 18425-1 18425-2 18424-1 7.2 22.8 4.39.40.813.187 Low 22-18 509-1,900.800.145 Brass.01.032 Insertion 18428-1 18428-2 18427-1 [0.2-0.9] 5.84 22.8 3.8.40.813.187 Low 1-14.300.900.173 Brass.01.032 Insertion 184235-1 184235-2 184234-1 7.2 22.8 4.39.40.813

PLASTI-GRIP Terminals and Splices Product Facts Pre-insulated PLASTI- GRIP solderless terminals and splices Designed specifically to answer the need for inexpensive, insulated electrical terminations Can be used in almost every type of commercial application Accommodate wire sizes from 22 AWG through 2/0 AWG The Crimp Carefully engineered application tooling has been developed to ensure uniformly high quality terminations Tool and terminal have been designed as a team to promote ease and speed of application and at the same time to provide precise crimping pressure for every wire size The wire and the terminal barrel form a homogeneous mass of metal, providing a connection of maximum conductivity, tensile strength, and high resistance to corrosion The quality performance, the facility of installation and the inherent simplicity make them wellsuited for many industrial applications Color Coding. Terminal insulation is color-coded by wire size range to eliminate errors during installation. Funnel Entry. Assures rapid wire insertion during high speed production. (Except 8 to 2/0 range.) Temperature Rating: 90 C Max. Basic Terminal. The basic terminal is constructed of fine grade high conductivity copper per ASTM B-152 and tin-plated per ASTM B-545. Basic material for Spring Spade Tongue Terminals is phosphor bronze per ASTM B-139 or brass per ASTM B-3 and tinplated per ASTM B-545. Tyco Electronics' special plating process creates durable corrosion resistance to salt spray and most chemical fumes. Serrations. Serrations inside barrel provide maximum contact and tensile strength after crimping. Dimples on 8 to 2/0 range.. Vinyl insulation sleeve provides good dielectric strength and supports the wire insulation so that no bare wire is exposed. AMP PLASTI-GRIP Terminals and Splices (Use PLASTI-GRIP or PIDG Tooling) AMP Wire Range 22-1 1-14 12- Listed Except as noted with individual part number listing. LR 7189 8 thru 4/0 Certified 00V Terminals, Butt & Parallel Splices 22-1 Solid or Stranded 1 00 V Max. Recognized under Terminals, Butt & Parallel Splices (00 V Fixture the component program 1-14 Solid or Stranded 1 or Sign) of Underwriters Terminals, Butt & Parallel Splices 90 C Max. Laboratories Incorporated File No. E13288 12- Solid or Stranded 1 Note: 22-1 terminals and splices are stamped 22-18 in accordance with MIL-T-7928. 1 Stranded wire only using TETRA-CRIMP tooling. PLASTIC-GRIP Terminals and Splices 37

PLASTI-GRIP Terminals and Splices (Continued) Ring Tongue Terminals L E W C -Vinyl, UL 94V-0 Terminal Body -Copper per ASTM B-152 Application Tooling-pg. A PLASTI-GRIP Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal Style [mm 2 ] Thickness Size W C E L Diameter Loose Tape Max. Min. Max. Max. Color Max. Piece Mounted 2 M2 A.218 5.54.15 3.9.572 14.53.84 17.37 134140* 2-34140-1.218 5.54.15 3.9.572 14.53.84 17.37 132944* 2-32944-1 4 A.218.15.572.84 5.54 3.9 14.53 17.37 134141* 2-34141-1. 1.92.809 20.55 34143 2-34143-1.218 5.54.15 3.9.572 14.53.84 17.37 132945* 2-32945-1.218 5.54.15 3.9.572 14.53.84 17.37 134142* 1-34142-1. 1.92.809 20.55 132947* 2-32947-1..809 134144* 2-34144-1 1.92 20.55 A M3.5..809 Black 1.92 20.55 32819 2-32819-1. 1.92.809 20.55 2-35449-1.97 17.70.85 21.74 32950 2-32950-1.97 17.70.85 21.74 134147* 2-34147-1. 1.92.809 20.55 132948* 2-32948-1 22-1 509-3,20.033..809 [0.2-1.5] 0.84 1.92 20.55 134145* 2-34145-1 8 M4 A.97 17.70.85 21.74 132951* 2-32951-1.97 17.70.85 21.74 134148* 2-34148-1.74 18.95.905 22.99.200 5.08 2-34148-4. 1.92.809 20.55 132949* 2-32949-1. 1.92.809 20.55 13414* 2-3414-1. 1.92.809 20.55 Black 2-3414-4 2-3414-5 A. 1.92.809 20.55 35451 2-35451-1.97 17.70.85 21.74 132952* 2-32952-1.97 17.70.85 21.74 134149* 2-34149-1.74 18.95.905 22.99.200 5.08 2-34149-3.49 11.91.437 11..853 21.7 1.090 27.9 132953* 2-32953-1 1/4 M A.49 11.91.437 11..853 21.7 1.090 27.9 134150* 2-34150-1.49 11.91.437 11..853 21.7 1.090 27.9 Black 2-34150-3 38

PLASTI-GRIP Terminals and Splices (Continued) Ring Tongue Terminals (Continued) Tongue Dimensions Wire Part Numbers Stud Terminal Style [mm 2 ] Thickness Size W C E L Diameter Loose Tape Max. Min. Max. Max. Color Max. Piece Mounted Note: C dimension applies from edge of metal wire barrel to center of stud hole. (Styles A & E)..49.437.853 1.090 1134151* 2-34151-1 5/1 11.91 11. 21.7 27.9 A M8 22-1.49.437.853 1.090 Black 2-34151-3 509-3,20.033 11.91 11. 21.7 27.9 [0.2-1.5] 0.84.531.54.92 1 13.49 13.87 24.43 31.24 1134152* 2-34152-2 3/8 A.531.54.92 1 Black 13.49 13.87 24.43 31.24 2-34152-4 4 A.171 4.34.587 14.91.715 18.1 1134157* 2-34157-1.171.587.715.145 4.34 14.91 18.1 3.8 1132957* 2-32957-1.171.587.715 1134158* 2-34158-1 4.34 14.91 18.1 M3.5 A.343.97.871.145 8.71 17.70 22.12 3.8 1132958* 2-32958-1.343 8.71.97 17.70.871 22.12 1134159* 2-34159-1. 1.92.825 20.9 1328527* 2-328527-1.343.97.871.145 1132959* 2-32959-1 8 8.71 17.70 22.12 3.8 A M4.343.97.871 8.71 17.70 22.12 113410* 2-3410-1.343 8.71.74 18.95.920 23.37 2-3410-2 2-3410-3.343.97.871 1-14.145 113290* 2-3290-1.033 8.71 17.70 22.12 3.8 0.84.343.97.871 8.71 17.70 22.12 113411* 2-3411-1 A.343 8.71.74 18.95.920 23.37 2-3411-2 2-3411-3.343 8.71.74 18.95.920 23.37 Black 2-34959-1.48 11.89.728 18.49.95 24.51 2-34954-1.49 11.91.437 11..853 21.7 1.090 27.9.145 3.8 113291* 2-3291-1 1/4 M A.49 11.91.437 11..853 21.7 1.090 27.9 113412* 2-3412-1.49 11.91.437 11..853 21.7 1.090 27.9 Black 2-3412-2 2-3412-3 5/1 M8 A.49 11.91.437 11..853 21.7 1.090 27.9 113413* 2-3413-1 3/8 A.531.54.92 1.248 1 13.49 13.87 24.43 31.70 13414* 2-3414-2.531.54.92 1.248 Black 13.49 13.87 24.43 31.70 2-3414-4 A.219.8.953 /Blk..200 M3.5 5.5 20.57 24.21 5.08 1 34821 2-34821-1 1-14HD 1 8 A.343.872 1.04 /Blk..200 11 34822.050 M4 8.71 22.15 2.57 5.08 1.27.343.872 1.04 /Blk..200 111 34823* 2-34823-1 8.71 22.15 2.57 5.08 A.343.872 1.04 /Blk. 8.71 22.15 2.57 321518 2-321518-1 Not UL or CSA Approved or Listed. 1 Heavy Duty for extra mechanical strength. Note: C dimension applies from edge of metal wire barrel to center of stud hole. (Styles A & E). PLASTIC-GRIP Terminals and Splices 39

PLASTI-GRIP Terminals and Splices (Continued) Ring Tongue Terminals (Continued) L E W C -Vinyl, UL 94V-0 Terminal Body -Copper per ASTM B-152 Application Tooling - pgs. & 7 A E PLASTI-GRIP Terminals and Splices 40 [mm 2 ] Tongue Dimensions Wire Part Numbers Stud Terminal Style Thickness Size W C E L Diameter Loose Tape Max. Min. Max. Max. Color Max. Piece Mounted.500.344.935 1.188 /Blk. 1/4 12.70 8.74 23.75 30.18 5.84 A M.531.437 1.028 1.29 /Blk..200 13.49 11. 2.11 32.92 5.08 1-14HD 1.050 5/1 A.531.437 1.028 1.29 /Blk..200 1.27 M8 13.49 11. 2.11 32.92 5.08 3/8 A.750 19.05.25 15.88 1.21 30.89 1.594 40.49 /Blk..200 5.08 1/2 M12 A.750 19.05.25 15.88 1.21 30.89 1.594 40.49 /Blk..200 5.08 0 A.219 5.5.8 20.57.953 24.21 4 A.219 5.5.8 20.57.953 24.21.219.8.953 5.5 20.57 24.21 A M3.5.375.302.893 1.098 9.53 7.7 22.8 27.89 5.84.302 7.7.893 22.8 1.02 2.97.302.893 1.02 8 7.7 22.8 2.97 A M4.375.302.893 1.098 9.53 7.7 22.8 27.89 5.84.375 9.53.302 7.7.893 22.8 1.098 27.89.302 7.7.893 22.8 1.052 2.72 5.84.302.953 1.111.300 7.7 24.21 28.22 7.2 12-12- A.375.302.893 1.083 Black 5,180-13,0.042 9.53 7.7 22.8 27.51 [2.2-.4] 1.07.375.302.893 1.098 9.53 7.7 22.8 27.89 5.84.375 9.53.302 7.7.893 22.8 1.098 27.89 E.400.1.48 11.89 1.118 28.40 1.373 34.87.300 7.2 1/4.500.344.994 1.247 Black.300 12.70 8.74 25.25 31.7 7.2 M A.531.48 1.059 1.327 13.49 11.89 2.90 33.71 5.84.531 13.49.48 11.89 1.059 2.90 1.327 33.71.531 13.49.48 11.89 1.059 2.90 1.327 33.71 5.84 5/1 M8 A.531 13.49.48 11.89 1.059 2.90 1.327 33.71 Black 5.84.531 13.49.48 11.89 1.059 2.90 1.327 33.71 3/8 A.593 15.0.531 13.49 1.122 28.50 1.421 3.09 5.84 1/2 M12 A.750 19.05.25 15.88 1.21 30.89 1.594 40.49 1 Heavy Duty for extra mechanical strength. Note: C dimension applies from edge of metal wire barrel to center of stud hole. (Styles A & E). 35349 2-35349-1 34824 2-34824-3 34825 3482 34827 2-34835-4 34835 2-34835-1 134852* 2-34852-1 13418* 2-3418-1 1 9047-1 1 9048-1 13419* 2-3419-1 134853* 2-34853-1 330518 1-330518-2 2-32821-1 134170* 2-34170-1 134854* 2-34854-1 1-5578-1 1-5578-2 35492 134171* 2-34171-1 134855* 2-34855-1 134172* 2-34172-1 2-34172-3 13485* 2-3485-1 134173* 2-34173-1 134837* 2-34837-4

PLASTI-GRIP Terminals and Splices (Continued) Ring Tongue Terminals (Continued) B C D F Tongue Dimensions Wire Part Numbers Stud Terminal Style [mm 2 ] Thickness Size W C E L Diameter Loose Tape Max. Max. Max. Color Max. Piece Mounted 8 M4 C.478 12.14.437 11. 1.344 34.14 1.58 40.28.30 9.14 52041 1-52041- D.430.437 1.33 1.05.30.92 11. 34.2 40.77 9.14 1-54351-2.431.437 1.338 1.55.30.95 11. 33.99 39.52 9.14 5223 1-5223-2 B.431.437 1.338 1.55.390.95 11. 33.99 39.52 9.91 1-5223-5 1-5223-4.431.437 1.358 1.57.330.95 11. 34.49 40.03 8.38 1-5223-1 1-5223-3 8 13,0-20,800.043.431.437 1.303 1.51.30 1-5521-1 1-5521-2 [.4-.5] 1.09.95 11. 33. 39.5 9.14 1/4 M C.478 12.14.437 11. 1.344 34.14 1.58 40.28.30 9.14 52041-1 52041-7.478 12.14.437 11. 1.358 34.49 1.00 40.4.330 8.38 52041-3* 52041-9 5/1 M8 C.587 14.91.500 12.70 1.400 35.5 1.9 43.08.30 9.14 52291*1 52291-4 3/8 C.587 14.91.500 12.70 1.400 35.5 1.9 43.08.30 9.14 52291-1* 52291-5 1/2 M12 A.875 22.23.25 15.88 1.420 3.07 1.80 47.24.330 8.38 5222-1.500.515 1.591 1.844.43 520421* 8 12.70 13.08 40.41 4.84 11.07 C M4.500.515 1.591 1.89.30 12.70 13.08 40.41 47.47 9.14 52042-2.48.421 1.482 1.719.30 11.89.9 37.4 43. 9.14 5225-4 B.48.421 1.482 1.719.43 11.89.9 37.4 43. 11.07 5225*1 5225-3.500.515 1.591 1.844.43 12.70 13.08 40.41 4.84 11.07 52042-4 C.500.515 1.591 1.89.30 52042-5* 20,800-33,0.048 12.70 13.08 40.41 47.47 9.14 [.5-1.8] 1.22 F.398.515 1.591 1.84.450.11 13.08 40.41 4.89 11.43 5579-1 5579-2 1/4.500.515 1.591 1.844.43 M 12.70 13.08 40.41 4.84 11.07 52042-1 52042-7 C.500.515 1.591 1.89.30 12.70 13.08 40.41 47.47 9.14 52042-3* 52042-9 5/1 M8 B.25 15.88.515 13.08 1.591 40.41 1.90 48.41.450 11.43 5224*1 5224-4 3/8 B.25 15.88.515 13.08 1.591 40.41 1.90 48.41.450 11.43 5224-1* 5224-5 1/2 M12 C.815 20.70.515 13.08 1.441 3.0 1.851 47.02.43 11.07 52350*1 Note: C dimension applies from edge of metal wire barrel to center of stud hole. (Styles A & E). PLASTIC-GRIP Terminals and Splices 41

PLASTI-GRIP Terminals and Splices (Continued) Ring Tongue Terminals (Continued) -Vinyl, UL 94V-0 Terminal Body -Copper per ASTM B-152 Application Tooling -pg. 7 B PLASTI-GRIP Terminals and Splices [mm 2 ] Tongue Dimensions Wire Part Numbers Stud Terminal Style Thickness Size W C E L Diameter Loose Tape Max. Max. Max. Color Max. Piece Mounted B.54 13.87.531 13.49 1.72 42.47 1.948 49.48.450 11.43 52043-2.54 13.87.531 13.49 1.72 42.47 1.948 49.48.515 13.08 520431* 52043-4.391 9.93.531 13.49 1.72 42.47 1.927 48.95.450 11.43 5580-2 1/4 M B.54 13.87.531 13.49 1.72 42.47 1.948 49.48.450 11.43 52043-3* 52043-7 4.051.54.531 1.72 1.948 33,0-52,00.515 1.30 13.87 13.49 42.47 49.48 13.08 52043-1 52043-5 [1.8-2.7].79.531 1.72 2.014.450 522-3 522-9 5/1 17.25 13.49 42.47 51.1 11.43 B M8.79.531 1.72 2.014.515 17.25 13.49 42.47 51.1 13.08 5221* 3/8 B.79 17.25.531 13.49 1.72 42.47 2.014 51.1.450 11.43 522-4* 1-522-0.79 17.25.531 13.49 1.72 42.47 2.014 51.1.515 13.08 522-1.75.578 1.731 2.071.50 5227-1 1/4 17.15 14.8 43.97 52.0 14.22 B M.75.578 1.731 2.071.32 17.15 14.8 43.97 52.0 1.05 52271*.711.578 1.731 2.089 2.50 52044-4 52,00-83,700.00 5/1 18.0 14.8 43.97 53.0 14.22 B [2.7-42.4] 1.52 M8.711.578 1.731 2.089.32 18.0 14.8 43.97 53.0 1.05 52044-1 3/8 B.711 18.0.578 14.8 1.731 43.97 2.089 53.0.50 14.22 52044-5.711 18.0.578 14.8 1.731 43.97 2.089 53.0.32 1.05 52044-2 5/1 M8 B.807 20.50.25 15.88 2.041 51.84 2.447 2.15.84 17.37 52045-1.807.25 2.041 2.447 1/0.5 52045-5 83,700-119,500.073 20.50 15.88 51.84 2.15 1.89 3/8 B [42.4-0.] 1.85.807.25 2.041 2.447.84 20.50 15.88 51.84 2.15 17.37 52045-2 1/2 M12 B.875 22.23.25 15.88 2.041 51.84 2.478 2.94.84 17.37 52289-1 2/0 119,500-150,500.083 5/1 B.92.25 2.082 2.477.775 [0.-7.3] 2.11 M8 23.52 15.88 52.88 2.92 19.9 5204-1 42

PLASTI-GRIP Terminals and Splices (Continued) Ring Tongue 90 Bend Terminals -Vinyl, UL 94V-0 Terminal Body -Copper per ASTM B-152 Application Tooling -pg. 7 Tongue Wire Dimensions Stud Terminal Part Numbers Thickness Size W D Diameter Loose [mm 2 ] Max. Min. Color Max. Piece.431.311.30 8.043.95 7.90 9.14 13,0-20,800 [.4-.5] 1.09 1/4.478.435.30 M 12.14 11.05 9.14.500.3.43.048 12.70 7.87 11.07 20,800-33,0 [.5-1.8] 1.22 1/4.500.379.43 M 12.70 9.3 11.07 Rectangular Tongue Terminals -Vinyl, UL 94V-0 Terminal Body -Copper per ASTM B-152 5554-1 54725-1 54753-1 54754-1 Performance Specifications - Application Tooling-pg. Tongue Dimensions Wire Stud Terminal Part Numbers Thickness Size W C E L X Diameter Loose Tape [mm 2 ] Max. Min. Max. Max. Color Max. Piece Mounted 1-14.033.249.728.88.145 0.84 M3.5.32 18.49 22.05 3.8 34898 Note: C dimension applies from edge of metal wire barrel to center of stud hole. PLASTIC-GRIP Terminals and Splices 43

PLASTI-GRIP Terminals and Splices (Continued) Spade Tongue Terminals -Vinyl, UL 94V-0 Terminal Body -Copper per ASTM B-152 Application Tooling-pg. PLASTI-GRIP Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal Thickness Size W C E L X Diameter Loose Tape [mm 2 ] Max. Min. Max. Max. Color Max. Piece Mounted.728 18.49.858 21.79 327043* 2-327043-1 M3.5.297 7.54.203 5.1.19 15.72.75 19.43.141 3.58 327735* 2-327735-1.297.203.19.75.141 7.54 5.1 15.72 19.43 3.58 3205* 2-3205-1 22-1 509-3,20.033.307.245.1.83.175 [0.2-1.5] 0.84 7.80.22 1.79 21.23 4.45 9003-1 9003-2 8 M4.375 9.53.728 18.49.920 23.37.187 4.75.120 * 2-32981-1.375 9.53.728 18.49.920 23.37.187 4.75 34155* 2-34155-1.375 9.53.728 18.49.920 23.37.187 4.75 3415* 2-3415-1 5.237.02.728 18.49.85 21.97.145 3.8 900-1.297 7.54.203 5.1.19 15.72.75 19.43.141 3.58.145 3.8 322994* 2-322994-1 M3.5.297 7.54.203 5.1.19 15.72.75 19.43.141 3.58 5437-1 2-5437-2.385.728.920.187 1-14 3415*.033 9.78 18.49 23.37 4.75 0.84.297.203.19.75.141 7.54 5.1 15.72 19.43 3.58 32741 2-32741-1 8 M4.307 7.80.245.22.1 1.79.83 21.23.175 4.45 9024-1 9024-2.385 9.78.728 18.49.920 23.37.187 4.75 341* 2-341-1.385 9.78.728 18.49.920 23.37.187 4.75 3417* 2-3417-1 12-5.237.29.887 1.095.203 9007-1.042.02 7.52 22.53 27.81 5.1 5.84 5,180-13,0 1.07 [2.2-.4].40.29.887 1.095.203.31 7.52 22.53 27.81 5.1 5.84 3417* 2-3417-1 Gold Note: C dimension applies from edge of metal wire barrel to center of stud hole. 44

PLASTI-GRIP Terminals and Splices (Continued) Flanged Spade Tongue Terminals -Vinyl, UL 94V-0 Terminal Body -Copper per ASTM B-152 Application Tooling-pg. Tongue Dimensions Wire Part Numbers Stud Terminal Thickness Size W C E L X H Diameter Loose Tape [mm 2 ] Max. Min. Max. Max. Min. Color Max. Piece Mounted.29.203.19.749.045 7.52 5.1 15.72 19.02 1.14 322249* 1-322249-1 M3.5.328.203.19.749.045 8.33 5.1 15.72 19.02 1.14 32450 2-32450-1 22-1.033.29.203.19.749.045 509-3,20 0.84 1-322249-0 1-322249-9 8 7.52 5.1 15.72 19.02 1.14 [0.2-1.5] M4.41..842.171.02.57 1.92 21.39 4.34 1.57 32419* 2-32419-1.29 7.52.203 5.1.19 15.72.749 19.02.045 1.14 32851* 2-32851-1.294.203.19.749.047 7.47 5.1 15.72 19.02 1.19 32415* 2-32415-1 M3.5.294.203.8.798.047 1-14 2-32415-4.033 7.47 5.1 1.97 20.27 1.19 0.84.294.203.19.749.047 53874-1 53874-2 8 7.47 5.1 15.72 19.02 1.19 M4.41..842.171.02.57 1.92 21.39 4.34 1.57 324170 2-324170-1 M3.5.29 7.52.841 21.3 1.017 25.83.171 4.34.052 1.32 5.84 324581* 1-324581-1 12-.042 8.41.841 1.017.171.052 5,180-13,0 1.07 M4.57 21.3 25.83 4.34 1.32 5.84 324172* 1-324172-0 [2.2-.4].41.841 1.017.171.052.57 21.3 25.83 4.34 1.32 5285 5285-1 Note: C dimension applies from edge of metal wire barrel to center of stud hole. PLASTIC-GRIP Terminals and Splices 45

PLASTI-GRIP Terminals and Splices (Continued) Short Spring Spade Tongue Terminals -Vinyl, UL 94V-0 Terminal Body -Phosphor Bronze per ASTM B-139 for wire sizes 24 to 14 Brass per ASTM B-3 for wire sizes 12 to except where noted Application Tooling-pg. PLASTI-GRIP Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal Thickness Size W C E L X Diameter Loose Tape [mm 2 ] Max. Min. Max. Max. Color Max. Piece Mounted 24-20 320-1,290.025 4.203.219.24.744.115 White [0.1-0.5] 0.4 5.1 5.5 15.85 18.90 2.92 53829-2 4.203 5.1. 1.92.811 20.0 52947*-1 52947-1 5 M3. 1.92.811 20.0 52948*-1 52948-1.234 5.94. 1.92.811 20.0 53240-1* 53240-2 M3.5. 1.92.811 20.0 52949*-1 52949-1.715 18.1.80 21.84.200 5.08 52949-2* 52949-3.244.97.872 22-1 53241-1* 53241-2.033.20 17.70 22.15 509-3,20 0.84 [0.2-1.5] 8.375.97.872 M4 9.53 17.70 22.15 52950*-1 52950-1.375 9.53.74 18.95.921 23.39.200 5.08 52950-2* 52950-3.294 7.47.97 17.70.920 23.37.218 5.54 53242-1* 53242-2.294 7.47.74 18.95.99 24.1.218 5.54.200 5.08 53242-5* 53242-.40.31.97 17.70.920 23.37.218 5.54 52951*-1 52951-1.40.31.74 18.95.99 24.1.218 5.54.200 5.08 52951-3. 1.92.811 20.0 52955*-1 52955-1 M3.5.715 18.1.80 21.84 52955-2* 52955-3.715 18.1.80 21.84 52955-4 1.244.20.97 17.70.872 22.15 53244-1* 53244-2.244.74.921 53244-4 8.20 18.95 23.39 1-14.033 M4.375.97.872 5295*-1 5295-1 0.84 9.53 17.70 22.15.375.74.921 9.53 18.95 23.39 5295-2* 5295-3.294 7.47.97 17.70.920 23.37.218 5.54 53245-1* 53245-2.294 7.47.74 18.95.99 24.1.218 5.54 53245-.40.31.97 17.70.920 23.37.218 5.54 52957*-1 52957-1.40.31.74 18.95.99 24.1.218 5.54 52957-2* 52957-3 1 Terminal body plating Gold per MIL-G-45204 over Nickel per QQ-N-290. Note: C dimension applies from edge of metal wire barrel to center of stud hole. 4

PLASTI-GRIP Terminals and Splices (Continued) Short Spring Spade Tongue Terminals (Continued) Tongue Dimensions Wire Part Numbers Stud Terminal Thickness Size W C E L X Diameter Loose Tape [mm 2 ] Max. Min. Max. Max. Color Max. Piece Mounted.174 4.42.775 19.9.959 24.3.179 4.55.200 5.08 5291*-1 5291-1 M3.5.174 4.42.775 19.9.959 24.3.179 4.55 5324-1* 5324-2.174 4.42.775 19.9.959 24.3.179 4.55 5324-3 1.27 7.01.877 22.28 1.052 2.72 53247-1* 53247-2 8.375.27.877 1.052.200 12-5292*-1 5292-1.042 M4 9.53 7.01 22.28 2.72 5.08 5,180-13,0 [2.2-.4] 1.07.375.27.93 1.111.300 9.53 7.01 23.77 28.22 7.2 5292-2* 5292-3.27 7.01.877 22.28 1.0 27.94.218 5.54 53248-1* 53248-2.40.31.27 7.01.877 22.28 1.0 27.94.218 5.54.200 5.08 5293*-1 5293-1.40.31.27 7.01.877 22.28 1.0 27.94.218 5.54 5293-2* 5293-3.40.31.27 7.01.93 23.77 1.159 29.44.218 5.54.300 7.2 5293-4* 5293-5 1 Terminal body plating Gold per MIL-G-45204 over Nickel per QQ-N-290. Note: C dimension applies from edge of metal wire barrel to center of stud hole. Long Spring Spade Tongue Terminals -Vinyl, UL 94V-0 Terminal Body -Phosphor Bronze per ASTM B-139 for wire sizes 22 to 14 Brass per ASTM B-3 for wire sizes 12 to Application Tooling-pg. PLASTIC-GRIP Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal Thickness Size W C E L X Diameter Loose Tape [mm 2 ] Max. Min. Max. Max. Color Max. Piece Mounted M3.5.238.05.4 1.87.945 24.00.27 7.01 52453* 52453-1 22-1.033 8.270.9.991.290 509-3,20 0.84 M4.8 17.8 25.17 7.37 52454* 52454-1 [0.2-1.5].343.283.709 1.017.303 8.71 7.19 18.01 25.83 7.70 52455* 52455-1 M3.5.238.05.4 1.87.945 24.00.27 7.01 5243* 5243-1 1-14.033 8.270.9.991.290 0.84 M4.8 17.8 25.17 7.37 5244* 5244-1.343.283.709 1.017.303 8.71 7.19 18.01 25.83 7.70 5245* 5245-1 8.375.273.874 1.174.295.200 M4 9.53.93 22.20 29.82 7.49 5.08 52474* 52474-1 12-.042.375.305.90 1.219.308.200 5,180-13,0 1.07 9.53 7.75 23.01 30.9 7.82 5.08 52475* 52475-1 [2.2-.4].375.305.95 1.278.308.300 9.53 7.75 24.51 32.4 7.82 7.2 52475-3 Note: C dimension applies from edge of metal wire barrel to center of stud hole. 47

PLASTI-GRIP Terminals and Splices (Continued) Slotted Ring Tongue Terminals -Vinyl, UL 94V-0 Terminal Body -Copper per ASTM B-152 Application Tooling-pg. Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 ] Thickness Size W C E L Diameter Loose Tape Max. Min. Max. Max. Color Max. Piece Mounted.218.15.572.58 22-1 340901.033 M3.5 5.54 3.9 14.53 1.71 509-3,20 0.84 [0.2-1.5] 8..782 M4 1.92 19.8 324184 2-324184-1 Note: C dimension applies from edge of metal wire barrel to center of stud hole. PLASTI-GRIP Terminals and Splices Hook Tongue Terminals -Vinyl, UL 94V-0 Terminal Body -Copper per ASTM B-152 Application Tooling-pg. Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 ] Thickness Size W C E L Diameter Loose Tape Max. Min. Max. Max. Color Max. Piece Mounted 1-14.033 8.343.97.871 32023 2-32023-1 0.84 M4 8.71 17.70 22.12 Note: C dimension applies from edge of metal wire barrel to center of stud hole. 48

PLASTI-GRIP Terminals and Splices (Continued) Flag Tongue Terminals A B -Vinyl, UL 94V-0 Color -Natural Terminal Body -Copper per ASTM B-152 Application Tooling-pg. Tongue Dimensions Terminal Wire Part Numbers Style Stud [mm 2 ] Thickness Size W C L D Stripe Diameter Loose Piece Max. Min. Max. Max. Color Max. 20-1HD 1 8-3,20.042 A 14.500.2.749.95 Green 322307 [0.41-1.5] 1.07 12.70.7 19.02 17.5 B.385.272.741.95 1-14 322834.033 9.78.91 18.82 17.5 0.84 A 14.500.2.749.95 12.70.7 19.02 17.5 3223 1-14HD 1.500.2.8.775 Black 322312.050 12.70.7 20.57 19.9 5.84 1.27 A 14.500.2.8.775 Black 12.70.7 20.57 19.9 5.84 322313.500.2.812.775 12.70.7 20.2 19.9 5.84 322315 12-.042 A 14.500.2.812.775 5,180-13,0 1.07 12.70.7 20.2 19.9 5.84 32231 [2.2-.4] 14.500.2.812.775.280 12.70.7 20.2 19.9 7.11 322395 1 Heavy Duty for extra mechanical strength. Multiple Stud Terminals -Vinyl, UL 94V-0 Terminal Body -Copper per ASTM B-152 Application Tooling-pg. PLASTIC-GRIP Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal [mm 2 ] Thickness Size W C E L Diameter Loose Tape Max. Min. Max. Max. Color Max. Piece Mounted 22-1 509-3,20.033-8-.325.271.91.99 [0.2-1.5] 0.84 8.2.88 17.55 24.1 54774-1 54774-2 1-14.033-8-.325.271.91.99.145 0.84 8.2.88 17.55 24.1 3.8 54775-1 54775-2 Note: C dimension applies from edge of metal wire barrel to center of stud hole. 49

PLASTI-GRIP Terminals and Splices (Continued) Butt Splices -Vinyl, UL 94V-0 Splice Body -Copper per ASTM B-152 Application Tooling-pg. PLASTI-GRIP Terminals and Splices Dimension Splice Wire Part Numbers 1 L Diameter Loose Tape [mm 2 ] Max. Color Max. Piece Mounted 2-22 202-8.20.080 [0.-0.41] 15.75 2.03 322* 2-322-1 22-18/1-14 1.05 27.05 / Stripe.115.8 2.92 90-1 1.05 27.05.120 3.05 3407* 2-3407-1 1.05 27.05 34243* 1-34243-1 22-1 1.07 Natural w/.120 2 27.33 Letters 3.05 324138* 509-3,20 [0.2-1.5] 1.07 27.33 34070* 1-34070-1 1.07 27.33 Natural w/ Stripes 55792-1* 55792-2 1.05 27.05.083 x.171 2.11 x 4.34 34203 3 *.00 15.24 5529-2 1.05 27.05 3408* 2-3408-1 1.05 27.05 Natural w/ Letters 328427* 1.05 1-14 27.05 34071* 2-34071-1 1.05 27.05 Natural Stripes w/ 55785-1* 55785-2 1.05 27.05.215 5.4 35244* 2-35244-1 1.5 28.07 2-34071-2 4 2-34071-3 4 1.05 27.05.135 x.245 3.43 x.22 34204 3 * 1-34204-0 1.10 29.4.200 5.08 3409 1.10 29.4 5.84 34072* 2-34072-2 1.10 29.4 Natural w/ Stripes 5.84 55793-1* 55793-2 1.10 12-29.4 34945* 5,180-13,0 [2.2-.4] 1.10.300 29.4 7.2 32742 1.200 30.48 2-34945-1 4 2-34945-2 4 1.10 29.4.15 x.315 4.19 x 8.00 32128 5 1.10 29.4.138 x 3.51 x 34205 3 * 8 1.340 34.04 9025-1 1.530 38.8.330 8.38 902-1 Not UL or CSA Approved or Listed. 1 When using two or more wires in either end of a butt splice, the combined cross sectional area must be within the (CMA) circular mil range listed. (Not UL or CSA approved with use of multiple wires.) 2 22-1 splices are 22-18 range in accordance with MIL-T-7928. 3 Oval expansion. 4 Funnel entry 50 5 Oval expansion at one end; circular expansion at other end.

PLASTI-GRIP Terminals and Splices (Continued) Parallel Splices -Vinyl, UL 94V-0 Splice Body -Copper per ASTM B-152 Application Tooling-pg. Dimension Splice Wire 1 L [mm 2 ] Max. Color Diameter Max..70.120 22-1 19.30 3.05 509-3,20 [0.2-1.5].70 19.30.70 19.30 1-14.70 19.30.70.135 x.245 19.30 3.43 x.22.843.200 12-21.41 5.08 5,180-13,0 [2.2-.4].870 22. 5.84 Part Numbers Loose Piece 1 When using two or more wires in a parallel splice, the combined cross sectional area must be within the (CMA) circular mil area listed. 2 Oval expansion. Shur-Plug (.093,.15 and.180 Series).093 Series.15 Series (.093 Series) -Vinyl, UL 94V-0 Terminal Body -Brass per ASTM B-3 (.15 &.180 Series) -Vinyl, UL 94V-0 Terminal Body -Copper per ASTM B-152 34131* 34132* 34133* 34134* 34207 2 * 34135 3413* Application Tooling-pg. PLASTIC-GRIP Terminals and Splices.180 Series Tongue Dimension Terminal Wire Part Numbers Series L Diameter Loose Tape [mm 2 ] Thickness Max. Color Max. Piece Mounted Max. 22-1 509-3,20.093.812 [0.2-1.5] 20.2 34178.15.800 1-14 324227* 1-324227-0.033 20.32 0.84.180.753 19.13 324228* Not UL or CSA Approved or Listed. 51

PLASTI-GRIP Terminals and Splices (Continued) 3-Way Connector -Vinyl, UL 94V-0 Terminal Body -Copper per ASTM B-152 Rivet -Brass per QQ-B-2 Application Tooling-pg. Tongue Dimensions Terminal Wire Thickness W L Diameter [mm 2 ] Max. Max. Max. Color Max. Part Number Loose Piece 1-14.033.877 1.400.145 34073* 0.84 22.28 35.5 3.8 PLASTI-GRIP Terminals and Splices Tube Cap Assembly -Vinyl, UL 94V-0 Terminal Body -Copper per ASTM B-152 Tube Cap -Copper/Zinc alloy per MIL-C-50 Rivet -Brass over Copper Tongue Dimensions Terminal Wire Thickness E L Diameter [mm 2 ] Max. Max. Max. Color Max. Application Tooling-pg. Part Number Loose Piece 22-1 509-3,20.033..978 Black 55137-1 [0.2-1.5] 0.84 1.92 24.84 Not UL or CSA Approved or Listed. Wire Pins Dimensions Terminal Wire Tab Ins. L Diameter Part Number [mm 2 ] Max. Color Max..070.943.145 911-1 (Tape) 22-1 1.78 23.95 3.8.071.135.905.145 1.80 3.43 22.99 3.8 1517 (Loose Piece) 52

Product Facts Designed to provide insulated terminals and splices for large wire sizes, many of which are used in airborne and ground support applications Tested under the procedures stipulated by MIL Spec. MIL-T-7928, they meet and exceed requirements Designed and engineered to withstand extreme vibration, shock and structural stresses, elevated temperatures and other conditions which could adversely affect the circuit requirements in complex air and space flight equipment The use of matching AMP tooling provides for precision crimping which makes all terminations identical This uniformity promotes maximum reliability and, coupled with tool die marks on the barrel indicating the wire size and color coding of the insulation sleeve, also serves as a built-in quality control factor Pre-insulated with color coded nylon which also acts as insulation support Wire size range of terminals is 8 AWG through 4/0 AWG TERMINYL Terminals and Splices Funnel Entry. Molded insulation for ease of wire insertion and snug fit over MIL-standard wire diameters. Dimples. Dimples afford maximum contact of barrel and wire and maximum tensile strength. Temperature Rating: 5 C Max. Basic Terminal. The basic terminal is constructed of fine grade high conductivity copper per ASTM B-152 and tin-plated per ASTM B-545. Tyco Electronics special plating process creates durable corrosion resistance to salt spray and most chemical fumes.. Nylon insulation for dielectric strength, color coded to wire size. TERMINYL Terminals meet or exceed the requirements of MIL-T-7928, Type II, Class 2. Refer to AMP Qualified Products for Military Application, Catalog 73-159 for Military Specification Number to AMP Part Number cross reference. TERMINYL Terminals and Splices 53

Ring Tongue Terminals TERMINYL Terminals and Splices (Continued) -Nylon, UL 94V-2 Terminal Body -Copper per ASTM B-152 Application Tooling -pg. 7 TERMINYL Terminals and Splices Tongue Dimensions Wire Part Numbers Stud Terminal Thickness Size W C E L Diameter Loose [mm 2 ] Max. Max. Max. Color Max. Piece 8 M4.478 12.14.437 11. 1.183 30.05 1.425 3.20.25.50 53041.431.95.437 11. 1.183 30.05 1.402 35.1.25.50 324043 8.043 1/4.478.437 1.183 1.425.25 13,0-20,800 1.09 M 12.14 11. 30.05 3.20.50 324082 [.4-.5] 5/1.587.500 1.24 1.542.25 M8 14.91 12.70 31.5 39.17.50 324044 3/8.587 14.91.500 12.70 1.24 31.5 1.542 39.17.25.50 324045.398.11.515 13.08 1.447 3.75 1.700 4.314 7.98 53119-1 1.48 11.89.421.9 1.338 33.99 1.575 40.01.314 7.98 32404.048 1/4.500.515 1.447 1.700.314 20,800-33,0 1.22 M 12.70 13.08 3.75 4 7.98 324047 [.5-1.8] 5/1.25.515 1.447 1.72.314 M8 15.88 13.08 3.75 44.75 7.98 324048 3/8.25 15.88.515 13.08 1.447 3.75 1.72 44.75.314 7.98 324049 8 M4.437 11..25.73 1.155 29.34 1.37 34.95.382 9.70 33145.437 11..25.73 1.155 29.34 1.37 34.95.382 9.70 1-33145-0.54 13.87.531 13.49 1.53 39.01 1.812 4.02.382 9.70 324111 4.051 1/4.54.531 1.53 1.812 33,0-52,00.382 1.30 M 13.87 13.49 39.01 4.02 9.70 324050 [1.8-2.7] 5/1.79.531 1.53 1.878.382 M8 17.25 13.49 39.01 47.70 9.70 324051 3/8.79 17.25.531 13.49 1.53 39.01 1.878 47.70.382 9.70 324052* 1/2 M12.79 17.25.531 13.49 1.53 39.01 1.878 47.70.382 9.70 324114 1/4 M.500 12.70.390 9.91 1.349 34.2 1.02 40.9.443 11.25 3309 4HD 3.094 5/1.79.45 1.55 1.907.443 33,0-52,00 2.39 M8 17.25 11.58 39.75 48.44 11.25 1-331421-0 [1.8-2.7] 3/8.79.45 1.55 1.907.443 17.25 11.58 39.75 48.44 11.25 1-331421-1.711 18.0.578 14.8 1.705 43.31 2.03 52.40.48 11.89 32855 1/4 M.79 17.25.578 14.8 1.705 43.31 2.045 51.94.48 11.89 324053 2.00 5/1.711.578 1.705 2.03.48 52,00-83,700 1.52 M8 18.0 14.8 43.31 52.40 11.89 324112 [2.7-42.4] 3/8.711.578 1.705 2.03.48 18.0 14.8 43.31 52.40 11.89 324054 1/2 M12.855 21.72.578 14.8 1.705 43.31 2.135 54.23.48 11.89 324055 1 Rectangular tongue terminal 2 90 bend ring tongue terminal 3 Heavy duty for extra mechanical strength. 54

TERMINYL Terminals and Splices (Continued) Ring Tongue Terminals (Continued) [mm 2 ] Tongue Dimensions Wire Part Numbers Stud Terminal Thickness Size W C E L Diameter Loose Max. Max. Max. Color Max. Piece 1/4.75.25 2.033 2.30.580 17.15 15.88 51.4 59.94 14.73 55822-1 M.807.25 2.033 2.42.580 20.50 15.88 51.4 1.2 14.73 32405 1/0 83,700-119,500.073 5/1.807.25 2.033 2.42.580 1.85 M8 20.50 15.88 51.4 1.2 14.73 324113 [42.4-0.] 3/8.807 20.50.25 15.88 2.033 51.4 2.42 1.2.580 14.73 324057 1/2 M12.875 22.23.25 15.88 2.017 51.23 2.454 2.33.580 14.73 324058 5/1.92.25 2.02 2.41. M8 23.52 15.88 51.4 1.37 15.49 324083 2/0 119,500-150,500.083.92.25 2.02 2.41. 2.11 3/8 23.52 15.88 51.4 1.37 15.49 324084 [0.-7.3] 1/2 M12.92 23.52.25 15.88 2.02 51.4 2.41 1.37. 15.49 324085 3/0 150,500-190,000.094 3/8 1.082.25 2.294 2.794.80 [7.3-9.3] 2.39 27.48 15.88 58.27 70.97 17.27 324185.835.25 2.295 2.700.75 21.21 15.88 58.29 8.58 19.43 329150 4/0 3/8 190,000-231,0.5 1.150.25 2.295 2.858.75 2.7 29.21 15.88 58.29 72.59 19.43 324187 [9.3-117] 1/2 M12 1.150 29.21.25 15.88 2.295 58.29 2.858 72.59.75 19.43 324188 TERMINYL Terminals and Splices 55

Butt Splices TERMINYL Terminals and Splices (Continued) Sleeve -Nylon, UL 94V-2 Splice Body -Copper per ASTM B-152 Application Tooling -pg. 7 TERMINYL Terminals and Splices Dimension Splice Wire Diameter Max. Style L Part Numbers [mm 2 ] Max. Color Single End Multiple End 8 to 12-13,0-20,800 [.4-.5] Single to Single w/ Step-Down 2.0 at.255 to Assembly 52.48 adapter end.48 5,180-13,0 32859 [2.2-.4] to 8 20,800-33,0 [.5-1.8] Single to Single w/ Step-Down 2.25 at.3 to Assembly 57.53 adapter end 7.87 13,0-20,800 328571 [.4-.5] 8 13,0-20,800 2.0.255 [.4-.5] 52.48.48 32425 20,800-33,0 2.25.3 [.5-1.8] Single to Single 57.53 7.87 3240 4 Standard Splice 33,0-52,00 2.804.370 [1.8-2.7] 71.22 9.40 32422 2 52,00-83,700 3.094.445 [2.7-42.4] 78.59 11.30 32423 8 13,0-20,800 2.171.255.335 [.4-.5] 55.14.48 8.51 32458 Single to Multiple 20,800-33,0 2.359.3.415 [.5-1.8] Standard Splice 59.92 7.87.54 32421 4 33,0-52,00 2.804.370.495 [1.8-2.7] 71.22 9.40 12.57 3242 8 13,0-20,800 2.27.335 [.4-.5] 57.81 8.51 32457 Multiple to Multiple 20,800-33,0 2.484.415 [.5-1.8] Standard Splice 3.09.54 32459 2 52,00-83,700 3.094.595 [2.7-42.4] 78.59 15.11 3243 1 Step-Down Assembly includes adapter which is visible through insulation sleeve window. 5

Product Facts Nylon window splice for military, commercial, aircraft, and missile applications that seals out vapors and fluids and imparts exceptional wire insulation support Metal rings at both ends of splice and permanently crimped to wire insulation for a moisture tight seal, even at altitude Designed to fit more than 0 insulation diameters in MIL-Spec wires from #24 to # AWG, and is available in three types First type is made with a nylon ring adapter within the wire entrance Second type, without nylon ring adapters Third type with a nylon ring adapter in one end only Special notch feature on the outside of the splice allows locator in the crimping tool to precisely position splice before crimping and to prevent twisting or horizontal movement during crimping Window area of each splice permits visual inspection of the linear plane of the crimp in relation to the inner metal sleeve Wire-stops in splice barrel indicate exact insertion depth of stripped wireends CERTI-SEAL Terminals and Splices Color Coding. The splice body is color coded by wire size: Tin plated for 24-20, for 22-18, for 1-14, for 12-. The metal rings are color coded green or orange to identify the presence of adapters. Rings. Metal rings at both ends permanently seal the splice to the wire insulation for a moisture tight seal. Adapters. Nylon ring adapter allows for smaller wire insulation diameters. Basic Splice. The basic splice body is constructed of fine grade high conductivity copper per ASTM B-152 and is either color coded or tin-plated per ASTM B-545. Tyco Electronics special plating process creates durable corrosion resistance to salt spray and most chemical fumes.. Nylon insulation assures high dielectric strength. Special notch feature allows crimping tool locator to position the splice to prevent twisting during crimping. CERTI-SEAL Terminals and Splices 57

Splice Splices with nylon wire insulation diameter adapters CERTI-SEAL Terminals and Splices (Continued) -Nylon, UL 94V-2 Splice Body -Copper per ASTM B-152 or Zinc Plate/Dye Chromate Application Tooling -shown below L Body Ring Wire Max. Color Color [mm 2 ] Dia. Max. Part Numbers Hand Tool Part No. 24-20 320-1,290.970 Tin Plated Green.05 [0.1-0.5] 24.4 1.5 324987 4073 24-20 320-1,290.970 Tin Plated Orange.073 [0.1-0.5] 24.4 1.85 1-324987-0 4073 22-18 509-1,900 1.15 Green.1 [0.2-0.9] 29.3 2.57 324988 4074 1-14 1.15 Green.120 29.3 3.05 324989 59282 12-5,180-13,0 1.345 Green.150 [2.2-.4] 34.1 3.81 324990 58325-1 CERTI-SEAL Terminals and Splices Splices without nylon wire insulation diameter adapters L Body Ring Wire Max. Color Color [mm 2 ] Dia. Max. Part Numbers Hand Tool Part No. 24-20 320-1,290.970 Tin Plated Tin Plated.0 [0.1-0.5] 24.4 2.54 324544 4073 22-18 509-1900 1.15 Tin Plated.133 [0.2-0.9] 29.3 3.38 324548 4074 1-14 1.15 Tin Plated.157 29.3 3.99 324549 59282 12-5,180-13,0 1.345 Tin Plated.218 [2.2-.4] 34.1 5.54 32431 58325-1 1.345.218 1-14 HD Tin Plated Tin Plated 5585-1 58325-1 34.1 5.54 Splices with nylon wire insulation diameter adapter in one end L Body Ring Wire Dia. Max. Part Hand Tool [mm 2 Max. Color Color Adapter End Other End Number Part No. ] 24-20 320-1,290.970 Tin Plated Orange & Tin Plated.073.0 1-324987-1 4073 [0.1-0.5] 24.4 1.85 2.54 Tooling Tool Part No. 4073 or 4074 Tool Part No. 59282 or 58325-1 Hand tooling features the AMP CERTI-CRIMP ratchet so that the operator fully closes tool so that crimping dies in tool head fully bottom. Locator feature in head assures that splice is properly oriented in tool. CERTI-SEAL Tools do not require wire insulation adjustment prior to crimping. 58

Class 1 and Class 2 Military Approvals Approval Dimensional Application Use Performance Requirement Tooling Requirement Terminals must comply Hand application tool For procurement with the dimensional which must conform to by government Class 1 requirements specified the military s dimensional agencies for by the military. and performance maintenance and specification. repair. Terminals must comply The terminal For procurement Per Military with the dimensional manufacturers by contractors Specification requirements specified recommended and Mil-T-7928G by the manufacturer s application tooling. manufacturers Class 2 customer drawing. For field repair purposes Note: Several tape mounted part numbers for high volume production, Class 2 terminals must are currently Class 2 modification, be capable of being approved. and repair. replaced by Class 1 Terminals. Military Specifications MS 2503 MS2503 PIDG Part Numbers AWG Dash Class Stud Size Loose Piece Tape Mounted Numbers 3149 1 & 2 1 2-3149-2 2 3150 1 & 2 2-3150-1 2 2 5183 1 & 2 5183-1 2 3153 1 & 2 2-3153-2 2 3 3154 1 & 2 22-18 2-3154-2 2 31895 1 & 2 5/1 4 2-31895-1 2 5/1 320572 1 & 2 5/1 2-320572-1 2 5/1 31897 1 & 2 3/8 5 2-31897-2 2 3/8 320573 1 & 2 3/8 2-320573-4 2 3/8 32051 1 & 2 2-32051-2 2 7 5184 1 & 2 5184-3 2 1-14 8 5184-2 1 & 2 5184-4 2 9 320575 1 & 2 5/1 2-320575-1 2 5/1 1 32054 1 & 2 3/8 2-32054-3 2 3/8 357 1 & 2 111 2-357-1 2 32057 1 & 2 2-32057-2 2 359 1 & 2 112 2-359-1 2 311 1 & 2 12-2-311-2 2 35111 1 & 2 5/1 113 2-35111-1 2 5/1 32057 1 & 2 5/1 2-32057-1 2 5/1 35112 1 & 2 3/8 114 320577 1 & 2 3/8 2-320577-3 2 3/8 Military Approvals 59

Class 1 and Class 2 Military Approvals (Continued) Military Specifications MS 2503 (Continued) AWG MS2503 Dash Numbers TERMINYL Part Numbers Loose Piece Tape Mounted Class Stud Size 115 324043 2 8 11 324082 2 1/4 117 324044 2 5/1 118 324045 2 3/8 119 32404 2 120 324047 2 1/4 121 324048 2 5/1 122 324049 2 3/8 123 324050 2 1/4 4 124 324051 2 5/1 125 324052 2 3/8 12 324053 2 1/4 2 127 324054 2 3/8 128 324055 2 1/2 129 32405 2 1/4 130 324057 2 3/8 1 1 131 324058 2 1/2 132 32405 2 1/4 1/0 133 324057 2 3/8 134 324058 2 1/2 135 324083 2 5/1 2/0 13 324084 2 3/8 137 324085 2 1/2 3/0 138 324185 2 3/8 4/0 140 324187 2 3/8 141 324188 2 1/2 1 Tyco Electronics recommends #1/0 AWG terminals for #1 AWG application. Military Approvals 0

Class 1 and Class 2 Military Approvals (Continued) Military Specifications MS 2503 (Continued) AWG MS2503 Dash Numbers Loose Piece PIDG Part Numbers Tape Mounted Class Stud Size 143 543-1 1 & 2 2 323913 2 2 144 52189 1 & 2 4 323914 2-323914-1 2 4 2-24 145 53073 1 & 2 32875 2-32875-1 2 14 54311-1 1 & 2 8 32391 2-32391-1 2 8 54312-1 1 & 2 147 54312-2 2 324075 2-324075-1 2 31880 1 & 2 4 148 2-31880-1 2 4 320553 1 & 2 4 2-320553-2 2 4 31890 1 & 2 8 22-18 149 2-31890-1 2 8 320551 1 & 2 8 1-320551-1 2 8 31894 1 & 2 1/4 150 2-31894-2 2 1/4 320571 1 & 2 1/4 2-320571-2 2 1/4 151 328975 1 & 2 1/2 152 324159 1 & 2 4 1-14 12-153 5184-1 1 & 2 8 5184-5 2 8 154 32053 1 & 2 1/4 2-32053-2 2 1/4 155 32897 1 & 2 1/2 358 1 & 2 8 15 2-358-1 2 8 32058 1 & 2 8 2-32058-1 2 8 351 1 & 2 1/4 157 2-351-1 2 1/4 32059 1 & 2 1/4 2-32059-3 2 1/4 Military Approvals 158 52077 2 1/2 1

Class 1 and Class 2 Military Approvals (Continued) Military Specifications M7928/1 M7928/1 PIDG- Restricting AWG Dash Part Numbers Class Stud Size Numbers Loose Piece Tape Mounted Military Approvals 1 53078 1 & 2 2 2 53049 1 & 2 4 2 3 53050 1 & 2 4 53051 1 & 2 8 5 53052 1 & 2 53053 1 & 2 2 7 53054 1 & 2 4 24 8 53055 1 & 2 9 5305 1 & 2 8 53057 1 & 2 11 52273 1 & 2 4 12 2-3149-3 1 & 2 13 5183-2 1 & 2 5183-5 2 22 14 1-320551-2 1 & 2 8 1-320551-5 2 8 15 2-3153-3 1 & 2 2-3153- 2 1 2-320571-3 1 & 2 1/4 17 2-320572-2 1 & 2 5/1 18 2-320573-1 1 & 2 3/8 19 2-328975-1 1 & 2 1/2 20 52273-1 1 & 2 4 21 2-3149-4 1 & 2 22 5183-3 1 & 2 5183-2 23 1-320551-3 1 & 2 8 20 2-3153-4 1 & 2 24 2-3153-8 2 25 2-320571-4 1 & 2 1/4 2 2-320572-3 1 & 2 5/1 27 2-320573-2 1 & 2 3/8 28 2-328975-2 1 & 2 1/2 29 52273-2 1 & 2 4 30 2-3149-5 1 & 2 31 5183-4 1 & 2 5183-7 2 18 32 1-320551-4 1 & 2 8 1-320551-8 2 8 33 2-3153-5 1 & 2 2-3153-9 2 34 2-320571-5 1 & 2 1/4 35 2-320572-4 1 & 2 5/1 3 2-320573-3 1 & 2 3/8 37 2-328975-3 1 & 2 1/2 38 52274 1 & 2 4 39 2-32051-3 1 & 2 40 5184-1 & 2 1-5184-2 2 41 1-5184-0 1 & 2 8 1 5184-7 1 & 2 42 1-5184-3 2 43 2-32053-3 1 & 2 1/4 44 2-320575-2 1 & 2 5/1 45 2-32054-1 1 & 2 3/8 4 2-32897-1 1 & 2 1/2 2

Class 1 and Class 2 Military Approvals (Continued) Military Specifications M7928/1 (Continued) M7928/1 PIDG- Restricting AWG Dash Part Numbers Class Stud Size Numbers Loose Piece Tape Mounted 14 12 47 52274-1 1 & 2 4 48 2-32051-4 1 & 2 49 5184-8 1 & 2 50 1-5184-1 1 & 2 8 1-5184-7 2 8 51 5184-9 1 & 2 1-5184-5 2 52 2-32053-4 1 & 2 1/4 53 2-320575-3 1 & 2 5/1 54 2-32054-2 1 & 2 3/8 55 2-32897-2 1 & 2 1/2 5 2-311-5 1 & 2 57 2-32058-2 1 & 2 8 58 2-311-3 1 & 2 59 2-32059-5 1 & 2 1/4 0 2-32057-2 1 & 2 5/1 1 2-320577-1 1 & 2 3/8 2 52077-1 2 1/2 3 2-311- 1 & 2 4 2-32058-3 1 & 2 8 5 2-311-4 1 & 2 2-311-8 2 2-32059- 1 & 2 1/4 2-32059-8 2 1/4 7 2-32057-3 1 & 2 5/1 8 2-320577-2 1 & 2 3/8 9 52077-2 2 1/2 Military Specifications M7928/4 M7928/4 PIDG PVF 2 AWG Dash Part Numbers Class Stud Size Numbers Loose Piece Tape Mounted 1 5340-1 1 & 2 53407-1 1 & 2 2 53407-2 2 22-18 3 53409-1 1 & 2 4 53411-1 1 & 2 5/1 5 53412-1 1 & 2 3/8 53415-1 1 & 2 7 5341-1 1 & 2 5341-2 2 1-14 53418-1 1 & 2 8 53418-2 2 9 53420-1 1 & 2 5/1 1 53421-1 1 & 2 3/8 111 53423-1 1 & 2 53425-1 1 & 2 112 12-53425-2 2 113 53427-1 1 & 2 5/1 114 53428-1 1 & 2 3/8 143 53400-1 1 & 2 2 144 53401-1 1 & 2 4 2-24 145 53402-1 1 & 2 14 53403-1 1 & 2 8 147 53404-1 1 & 2 Military Approvals 3

Class 1 and Class 2 Military Approvals (Continued) Military Specifications M7928/4 (Continued) M7928/4 PIDG PVF 2 AWG Dash Part Numbers Class Stud Size Numbers Loose Piece Tape Mounted 22-18 1-14 12-148 53405-1 1 & 2 4 149 53408-1 1 & 2 8 53408-2 2 8 150 534-1 1 & 2 1/4 534-2 2 1/4 151 53413-1 1 & 2 1/2 152 53414-1 1 & 2 4 153 53417-1 1 & 2 8 154 53419-1 1 & 2 1/4 155 53422-1 1 & 2 1/2 15 53424-1 1 & 2 8 53424-2 2 8 157 5342-1 1 & 2 1/4 158 53429-1 2 1/2 Military Approvals Military Specifications M7928/ 5 Military Specifications M7928/ M7928/5 PIDG Window Splice AWG Dash Part Numbers Class Numbers Loose Piece Tape Mounted 2-24 1 323994 1 & 2 24-20 2 323975 1 & 2 2-323975-3 2 22-18 3 320559 1 & 2 2-320559-4 2 1-14 4 32052 1 & 2 2-32052-3 2 12-5 320570 1 & 2 M7928/ PIDG Window Splice PVF 2 AWG Dash Part Numbers Class Numbers Loose Piece Tape Mounted 2-24 1 5354-1 1 & 2 24-20 2 53547-1 1 & 2 53547-2 2 22-1 3 53548-1 1 & 2 53548-2 2 1-14 4 53549-1 1 & 2 4

Class 1 and Class 2 Military Approvals (Continued) Military Specifications MS 17143 MS17143 PIDG AWG Dash Part Numbers Class Stud Size Numbers Loose Piece Tape Mounted 22-18 1 327932 1 & 2 8 1-14 2 2-327934-2 1 & 2 8 12-3 32793 1 & 2 8 22-18 4 2-327938-1 1 & 2 2-327938-2 2 1-14 5 2-327940-4 1 & 2 12-327942 1 & 2 22-18 7 327944 1 & 2 8 2-327944-2 2 8 1-14 8 2-32794-4 1 & 2 8 12-9 327948 1 & 2 8 22-18 2-327950-1 1 & 2 5 1-14 11 2-327952-2 1 & 2 5 2-327952- 2 5 12-12 327954 1 & 2 5 2-327954-2 2 5 22-18 13 2-32795-1 1 & 2 1-14 14 2-327958-4 1 & 2 12-15 2-32790-1 1 & 2 2-32790-2 2 22-18 1 32792 1 & 2 4 1-14 17 2-32794-4 1 & 2 4 12-18 3279 1 & 2 4 22-18 19 2-32798-1 1 & 2 4 1-14 20 2-327970-4 1 & 2 4 12-21 327972 1 & 2 4 Military Approvals 5

Tooling Tooling Insulated Terminals and Splices 30 to AWG Wire Range Description AMP Wire Range 30-2 Tools for Loose Piece Termination Tools for Tape Mounted Terminations Hand Tools Pneumatic Tools Tape Dies for Tape Dies for Tape Dies for Tape Dies for Tape Dies for Single Multi- Heads for Heads for Dies for 9875 354500-1 818380-1 AMPOMATOR 55435-5 Wire Wire -2-2 935, AMP-TAPETRONIC AMP-O-LECTRIC AUTO-PRO CLS III G, CLS IV AMP-O-LECTRIC Range Range Single Wire Multi-Wire 935-2, No Applicator Model G Applicator Applicator Model K Range Range 97-1 3, Required Applicator 818057-2 8758-1 Applicator 4 57200-3 57200-2 217200-1 913 uses 2-22 Terms. 2-22 4121 59275 314537-1 9344 9877 9877 9877 9877 9877 PIDG 59250 Terminals & 22-1 4738 59824-1 314270-3 79305-1 4780-2 Splices 58433-32 and 8343-1 59250 PLASTI-GRIP 1-14 ( exp.) 59824-1 1 Terminals 47387 58433-3 2 31429-1 79305-1 47807-1 12-1-14 HD 2-22 22-1 59239-4 59287-2 (.300 exp.) 4121 (butt spl. only) 4510 (butt spl. only) 45449 (parallel spl. only) 59824-1 1 58433-3 2 47808- Std. 79300-1 79305-1 47808-5 (.300 exp.) 9872* 9872* 9872* 9872* 9872* 5982-1 1 5982-1 1 5982-1 1 5982-1 1 5982-1 1 9873* 9873* 9873* 9873* 9873* 59827-1 1 59827-1 1 59827-1 1 59827-1 1 59827-1 1 9874* 9874* 9874* 9874* 9874* 9897 9897 9897 9897 9897 (.300 exp.) (.300 exp.) (.300 exp.) (.300 exp.) (.300 exp.) 59828-1 1 59828-1 1 59828-1 1 59828-1 1 59828-1 1 58433-3 2 31488-1 (butt spl. (butt spl. only) only) 45575-1 58433-3 2 31489-1 PLASTI-GRIP (butt spl. only) 1-14 (butt spl. (butt spl. Splices 45450 only) only) (parallel spl. only) 9872 9872 9872 9872 9872 (butt spl. only) (butt spl. only) (butt spl. only) (butt spl. only) (butt spl. only) 9873 9873 9873 9873 9873 (butt spl. only) (butt spl. only) (butt spl. only) (butt spl. only) (butt spl. only 59489 (butt spl. only) 59287-1 58433-3 12-2 9874 9874 9874 9874 9874 (.300 exp. (butt spl. 1-14 HD (butt spl. only) (butt spl. only) (butt spl. only) (butt spl. only) (butt spl. only) butt spl. only) only) 59270 (parallel spl. only) Tooling with adjustable insulation crimp. *Same die set/configuration as in hand tools. 1 TETRA-CRIMP die configuration. 2 PRO-CRIMPER II commercial tool not approved for UL applications. 3 97-1 hand tool. 4-2 Pneumatic Tool Adapter

Insulated Terminals and Splices 8 to 4/0 AWG Wire Range Tools for Loose Piece Terminations Tools for Tape Mounted Terminations Description Wire Hand Tools Dies for Crimp Head Dies for Head for Dies for Dies for AMP- Size 9051 1 Crimp Head Pneumatic AMP-TAPETRONIC TAPETRONIC Machine & Hydraulic Hand Tool 90 1 Hand Tool Machine with 59974-1 & 58422-1 1 9015 8250-1 Adjustment 8250-2 8 9959 48752-1 47820 8247-1 2 1214512-13 1214512-2 4 48753-1 47821 2 8325-1 8248-1 2 1213500-2 1213500-13 PLASTI-GRIP 4 48754-1 Terminals 47822 8249-1 2 1213098-13 1213098-2 4 and Splices 2 48755-1 47823 2 1/0 4875-1 2/0 48757-1 8 47820 8285-1 47821 4 47822 Terminyl 2 47823 Terminals 1/0 47824 and Splices 2/0 47825 3/0 47915 4/0 47918 4 HD 943 1 Heads for Power Units 9120-1, 9120-2, or 314979-1. 2 No insulation crimp. 3 Without insulation crimp. 4 With insulation crimp. Tooling (Continued) Tooling Insulated FASTON Terminals and Splices 2 to AWG Wire Range Tools for Tape Mounted Terminations Tools for Strip Form Terminations Hand Tool Tape Dies for Tape Dies for Tape Dies for AMPOMATOR 9875 AMP-TAPETRONIC AMP-O-LECTRIC 1 AMPOMATOR CLS III G, CLS IV No Applicator Required Model G CLS III G, CLS IV Applicators Applicator 57200-3 Applicator 8758-1 2-24 48518-2 9877-2 9877-2 9877-2 22-18 59824-1 5982-1 5982-1* 5982-1 4788-3 2 22-18 (Natural) 90185-1 90248-2 90248-2 90248-2 4554-3 1-14 59824-1 59827-1 59827-1* 59827-1 4789-3 2 14-12 9024-1 90240-2 90240-2 90240-2 12-59824-1 59828-1 59828-1* 59828-1 4790-4 2 *Only UL and CSA approved. 1 AMP-O-LECTRIC Model K 55435-5 uses applicator 57200-2. 2 Die included with applicator. 7

Tooling (Continued) Loose Form Terminal and Splice Tooling CERTI-CRIMP Hand Tools Double Action Hand Tool Heavy Head Hand Tool C Head Straight Action Hand Tool Part No. 97-1 PRO-CRIMPER II Hand Tool Part No. 58433-3 T-HEAD Tool Part No. 59250, 59275 Tetra-Crimp Hand Tool Tooling Part No. 59824-1 Hydraulic Hand Tools Part No. 59974-1 (Dies Required) 8

Tooling (Continued) Pneumatic Tools Part No. 935 (Hand Actuation) Part No. 935-2 (Foot Actuation) Part No. 9015 Crimping Heads Part No. 58422-1 (408-9535) Part No. 90 (408-2453) Tooling Part No. 9051-2 Tool 9

Tooling (Continued) Tape Mounted AMP-TAPETRONIC Machine 9875, 8250-1 (Requires Dies) AMP-O-LECTRIC, Model G Machine (Requires Applicator and Dies) Tooling AUTO-PRO Machine 818380-1 (Requires Applicator and Dies) AMPOMATOR CLS IV Machine 217500-1 (Requires Applicator and Dies) 70

Part Number Index Note: This index lists all cataloged parts by base no. only. Complete part nos. (with prefixes and/or suffixes) are shown on the page(s) indicated. Part No. Page 31880 9 31884 14 31885 14 3188 9 31887 9 31888 14 31890 9 31891 14 31894 31895 31897 31903 14 32050 21 32051 21 32053 21 32054 21 3205 22 32057 22 32058 22 32059 22 3200 22 32403 21 32404 21 3244 32 32448 32 3245 2 32497 23 32498 23 325 23 3251 23 3252 23 32588 22 32589 22 32835 9 3283 9 32837 9 32883 12 32944 38 32945 38 32947 38 32948 38 32949 38 32950 38 32951 38 32952 38 32953 38 32957 39 32958 39 32959 39 3290 39 3291 39 32981 44 33155 23 3315 23 3318 20 33172 20 33173 20 3347 19 3343 14 33724 11 Part No. Page 33734 11 3407 50 3408 50 3409 50 34070 50 34071 50 34072 50 34073 52 34080 21 34090 48 34131 51 34132 51 34133 51 34134 51 34135 51 3413 51 34140 38 34141 38 34142 38 34143 38 34144 38 34145 38 3414 38 34147 38 34148 38 34149 38 34150 38 34151 39 34152 39 34155 44 3415 44 34157 39 34158 39 34159 39 3410 39 3411 39 3412 39 3413 39 3414 39 3415 44 341 44 3417 44 3418 40 3419 40 34170 40 34171 40 34172 40 34173 40 3417 44 34178 51 34203 50 34204 50 34205 50 34207 51 34243 50 34294 30 34313 2 3440 2 34512 20 34541 21 34805 11 3480 11 348 11 34821 39 34822 39 Part No. Page Part No. Page 34823 39 34824 40 34825 40 3482 40 34827 40 34835 40 34837 40 34852 40 34853 40 34854 40 34855 40 3485 40 34898 43 34945 50 34954 39 34959 39 34974 11 35 11 357 12 358 12 359 12 351 12 35111 13 35112 13 35148 12 35149 12 35150 13 35151 13 35152 22 3521 2 35229 9 35244 50 35273 12 35274 11 35279 20 3531 12 35345 14 3534 14 35349 40 3532 14 3533 14 3534 14 35440 2 35449 38 35451 38 35478 14 35481 2 35492 40 35538 14 35559 22 3504 14 3505 14 3534 11 3572 32 35787 12 3149 9, 15, 1 3150 9 3151 9 3152 9 3153 9, 15, 1 3154 9 3157 3158 310 11 311 12, 17 3203 12 3254 9 3485 14 3954 2 42844 34 50534 8 50881 5181 14 5183 9, 15, 1 5184, 11, 1, 17 51874 23 52041 41 52042 41 52043 42 52044 42 52045 42 5204 42 52077 13, 17 52124 8 52189 8 5222 41 5223 41 5224 41 5225 41 522 42 5227 42 52273 15, 1 52274 1, 17 52283 28 52284 28 52289 42 52291 41 52307 15, 1 52350 41 5239 23 52403 25 52408 25 52409 25 524 25 52411 25 52420 25 52421 25 52422 25 52423 25 52430 25 52431 25 52432 25 52433 25 52453 47 52454 47 52455 47 5243 47 5244 47 5245 47 52474 47 52475 47 5285 45 52921 24 52922 24 52923 24 52924 24 52925 24 52927 24 52928 24 52929 24 Part Number Index 71

Part Number Index (Continued) Part Number Index Part No. Page Part No. Page Part No. Page 52930 24 52931 24 52933 24 52934 24 52935 24 5293 24 52937 24 52939 24 52940 24 52941 24 52942 24 52943 24 52945 24 52947 4 52948 4 52949 4 52950 4 52951 4 52955 4 5295 4 52957 4 5291 47 5292 47 5293 47 53041 54 53049 15 53050 15 53051 15 53052 15 53053 15 53054 15 53055 15 5305 15 53057 15 53073 8 53078 15 53115 21 53119 54 53222 29 53240 4 53241 4 53242 4 53244 4 53245 4 5324 47 53247 47 53248 47 5354 31 53547 31 53548 31 53549 31 53550 31 53829 4 53874 45 53912 21 53914 21 53941 53942 11 543 8 54311 8 54312 8 54351 41 5437 44 54725 43 54753 43 54754 43 54771 27 54773 27 54774 49 54775 49 55137 52 55148 18 55157 14 55319 35 5521 41 5529 50 5554 43 5575 34 5578 40 5579 41 5580 42 5585 58 5594 19 5578 24 55777 19 55785 50 55792 50 55793 50 55822 55 5593 0544 34 0893 35 0894 35 48 35 59 35 0 35 1198 34 178 35 150247 1517 52 15429 29 184234 35 184235 35 18421 34 18422 34 18424 34 18425 34 18427 35 18428 35 320209 19 32023 48 32030 2 320381 2 320551 9, 15, 1 320552 9 320553 9 320554 9 320555 32 320559 31 32050 32051, 1, 17 32052 31 32053 11, 1, 17 32054 11, 1, 17 32055 3205 32 32057 12 32058 12, 17 32059 12, 17 320570 31 320571, 15, 1 320572, 15, 1 320573, 15, 1 320574 11 320575 11, 1, 17 32057 13, 17 320577 13, 17 32019 32020 32 32027 11 32029 19 32030 11 32031 11 32034 12 3205 44 320773 9 32081 23 32082 23 32083 23 320882 9 3213 8 322 50 3235 21 3245 11 32120 19 321233 22 321235 3 321283 20 32128 50 321518 39 321522 32111 2 32117 8 32120 8 32188 3 321808 2 322001 21 322238 14 322249 45 322307 49 3223 49 322312 49 322313 49 322315 49 32231 49 322395 49 32242 23 322724 12 322777 23 322834 49 322985 22 322994 44 323008 9 323011 2 323039 27 3237 32382 11 323758 9 32372 12 32373 14 323784 13 323817 27 323818 27 323912 8 323913 8 Part No. Page 323914 8, 15 323915 8 32391 8, 15 323975 31 323985 8 32398 8 323989 8 323990 8 323994 31 324011 27 324015 23 324043 54, 0 324044 54, 0 324045 54, 0 32404 54, 0 324047 54, 0 324048 54, 0 324049 54, 0 324050 54, 0 324051 54, 0 324052 54, 0 324053 54, 0 324054 54, 0 324055 54, 0 32405 55, 0 324057 55, 0 324058 55, 0 324075 8 324082 54 324083 55, 0 324084 55, 0 324085 55, 0 32408 11 324111 54 324112 54 324113 1 324114 54 324123 324138 50 324158 9 324159 32415 45 32419 45 324170 45 324172 45 324184 48 324185 55, 0 324187 55, 0 324188 55, 0 324225 29 324227 51 324228 51 324533 11 324543 30 324544 58 324548 58 324549 58 324557 23 32450 45 32457 23 324577 23 324581 45 324587 23 324597 23 32403 20 72

Part Number Index (Continued) Part No. Page Part No. Page Part No. Page 32408 23 32415 13 32421 5 32422 5 32423 5 32425 5 32431 58 32457 5 32458 5 32459 5 3240 5 3242 5 3243 5 324915 12 324918 12 324987 58 324988 58 324989 58 324990 58 324993 325034 11 325148 19 325150 23 325197 22 325199 22 32741 44 32742 50 32819 38 32859 22 3281 21 3285 23 32875 8, 15 3287 21 32878 9 32882 3288 12 327043 44 327174 9 327583 31 32735 32 3273 32 32737 32 32738 31 32739 31 32754 9 327717 21 327735 44 327743 11 327748 30 327932 19 327934 20 32793 20 327938 19 327940 20 327942 20 327944 19 32794 20 327948 20 327950 19 327952 19 327954 20 32795 19 327958 20 32790 20 32792 19 32794 19 3279 20 32798 19 327970 19 327972 20 32821 40 328281 22 328394 21 328427 50 328489 8 32851 45 328527 39 32859 5 328571 5 32855 54 32857 9 328849 11 32891 31 328975, 15, 1 32897 11, 1, 17 32899 328998 11 328999 11 329150 55 329389 12 329391 11 3293 8 32997 20 329951 8 330250 19 330518 40 33048 9 33089 12 3309 54 33128 20 3313 23 331421 54 331453 2 33145 54 33147 13 350871 35 30025 3 30035 3 40174 34 40578 34 40902 34 40903 34 40904 34 40905 34 4090 34 40907 34 40908 34 40909 34 409 34 40911 34 40913 34 40915 34 4091 34 40917 34 40918 35 40919 35 40921 35 40922 35 40923 35 40924 35 40925 35 40927 35 40929 35 40931 35 41317 35 41320 34 41321 34 41324 35 9003 44 900 44 9007 44 90 50 9018 34 9020 18 9024 44 9025 50 902 50 9047 40 9048 40 907 2 9077 2 98 35 911 52 Part Number Index 73

Americas Argentina Buenos Aires Phone: +54-11-4733-2200 Fax: +54-11-4733-2211 Brasil São Paulo Phone: +55-11-23-000 Fax: +55-11-23-030 Chile Santiago Phone: +5-2-345-031 Fax: +5-2-223-1477 Contact Us Worldwide Canada Toronto Phone: +905-475-222 Fax: +905-474-5520 Product Information Center: Phone: +905-470-4425 Fax: +905-474-5525 Colombia Bogota Phone: +57-1-319-8959 Fax: +57-1-319-890 Mexico Mexico City Phone: +52-55-1-0800 +01-800-733-892 Fax: +52-55-1-0901 For Latin/South American Countries not shown Phone: +54-11-4733-2015 Fax: +54-11-4733-2083 United States Harrisburg, PA Phone: +1-717-54-00 Fax: +1-717-98-7575 Product Information Center: Phone: +1-800-522-752 Fax: +1-717-98-7575 Troy, MI Phone: +1-248-273-3359 Fax: +1-248-273-3322 Asia/Pacific Australia Sydney Phone: +1-2-9554-200 Fax: +1-2-9502-255 Product Information Center: Phone: +1-2-9840-8200 Fax: +1-2-934-188 India Bangalore Phone: +91-80-285-40800 Fax: +91-80-285-40820 Indonesia Jakarta Phone: +5-482-0311 Fax: +5-482-12 Japan Kawasaki, Kanagawa Phone: +81-44-844-8111 Fax: +81-44-812-3207 Product Information Center: Phone: +81-44-844-8013 Fax: +81-44-812-3200 Korea Seoul Phone: +82-2-3415-4500 Fax: +82-2-348-38 Malaysia Selangor Phone: +0-3-7805-3055 Fax: +0-3-7805-30 New Zealand Auckland Phone: +4-9-34-4580 Fax: +4-9-34-458 Philippines Makati City Phone: +32-848-0171 Fax: +32-87-81 People s Republic of China Hong Kong Phone: +852-2735-128 Fax: +852-2735-0243 Shanghai Phone: +8-21-2407-1588 Fax: +8-21-2407-1599 Singapore Singapore Phone: +5-482-0311 Fax: +5-482-12 Taiwan Taipei Phone: +88-2-878-2788 Fax: +88-2-878-228 Thailand Bangkok Phone: +-2-955-0500 Fax: +-2-955-0505 Vietnam Ho Chi Minh City Phone: +84-8-930-554 Fax: +84-8-930-3443 Global Contacts 74 Europe/Middle East/Africa Austria Vienna Phone: +43-1-905-0-0 Fax: +43-1-905-0-1333 Product Information Center: Phone: +43-1-905-0-1249 Fax: +43-1-905-0-1251 Belarus Minsk Phone: +375 17 237 47 94 Fax: +375 17 237 47 94 Belgium Kessel-Lo Phone: +32-1-352-300 Fax: +32-1-352-352 Bulgaria Sofia Phone: +359-2-971-2152 Fax: +359-2-971-2153 Czech Republic and Slovakia Czech Republic Kurim Phone: +420-541-12-111 Fax: +420-541-12-223 Product Information Center: Phone: +420-541-12-113 Fax: +420-541-12-132 Denmark Glostrup Phone: +45-43-48-04-00 Fax: +45-43-44-14-14 Egypt Cairo Phone: +202-419-2334 Fax: +202-417-747 Estonia Tartu Phone: +372-5138-274 Fax: +372-7400-779 Finland Helsinki Phone: +358-95-12-34-20 Fax: +358-95-12-34-250 France Cergy-Pontoise Cedex Phone: +33-1-3420-8888 Fax: +33-1-3420-800 Product Information Center: Phone: +33-1-3420-88 Fax: +33-1-3420-823 France Export Divisions Cergy-Pontoise Cedex Phone: +33-1-3420-8804 Fax: +33-1-3420-899 Germany Bensheim Phone: +49-251-133-0 Fax: +49-251-133-100 Product Information Center: Phone: +49-251-133-1999 Fax: +49-251-133-1988 Greece Athens Phone: +30-2-9370-39/397 Fax: +30-2-9370-55 Hungary Budapest Phone: +3-1-289-00 Fax: +3-1-289- Product Information Center: Phone: +3-1-289-1 Fax: +3-1-289-17 Ireland Dublin Phone: +353-1-8-512 Fax: +353-1-8-5714 Israel Petach-Tikva Phone: +972-3-929-0999 Fax: +972-3-919-88 Italy Collegno (Torino) Phone: +39-011-4012-111 Fax: +39-011-4031-11 Product Information Center: Phone: +39-011-4012-428 Fax: +39-011-40-287-428 Lithuania and Latvia Lithuania Vilnius Phone: +370-5-213-1402 Fax: +370-5-213-1403 Product Information Center: Phone: +370-5-211-301 Fax: +370-5-213-1403 Netherlands s-hertogenbosch Phone: +31-73-24-24 Fax: +31-73-212-35 Product Information Center: Phone: +31-73-24-999 Fax: +31-73-24-998 Norway Nesbru Phone: +47--77-88-50 Fax: +47--77-88-55 Poland Warsaw Phone: +48-22-457-700 Fax: +48-22-457-720 Product Information Center: Phone: +48-22-457-704 Fax: +48-22-457-720 Romania Bucharest Phone: +40-21-311-3479/359 Fax: +40-21-312-0574 Russia Moscow Phone: +7-495-790-7902 Fax: +7-495-721-1893 Product Information Center: Phone: +7-495-790-7902-404 Fax: +7-495-790-7902-401 Russia St. Petersburg Phone: +7-812-718-8192 Fax: +7-812-718-8193 Slovenia Ljubljana Phone: +38-151-3270 Fax: +38-151-3240 South Africa Port Elizabeth Phone: +27-41-503-4500 Fax: +27-41-581-0440 Spain Barcelona Phone: +34-93-291-0330 Fax: +34-93-201-7879 Sweden Upplands Väsby Phone: +4-8-50-72-50-00 Fax: +4-8-50-72-50-01 Switzerland Steinach Phone: +41-71-447-0447 Fax: +41-71-447-0444 Turkey Istanbul Phone: +90-212-281-8181/2/3 +90-212-282-5130/5430 Fax: +90-212-281-8184 Ukraine Kiev Phone: +380-44-20-225 Fax: +380-44-20-224 Product Information Center: Phone: +380-44-20-225 Fax: +380-44-20-224 United Kingdom Stanmore, Middlesex Phone: +44-870-080208 Fax: +44-208-954-234 Product Information Center: Freephone (UK only): 0800-27- Phone: +44-870-080208 Fax: +44-208-420-8095

Engineering Notes Engineering Notes 75

Tyco Electronics Corporation Harrisburg, PA 82042 - Rev. 7/08 - OG3B