Socket P2RF-05-S P2RF-08-S Clip & Release Lever R99-11 nameplate for MY

Transcription

1 Screwless Clamp Terminal Socket Screwless clamping greatly contributes to reducing wiring time. No over or under tightening of cable connection so better contact reliability is achieved. Double wiring possible on all the terminals, and easy bridge and branch connections. Use either solid or standard wires from 0.2 to 1.5 mm 2 (AWG24 to AWG16). Safe terminal arrangement: Coil terminals separated from contact terminals. Unique ejector enables easy relay replacement. Two types of nameplate are available: New MY and Legrand. Finger-protection construction. VDE, UL, CSA approval pending. Ordering Information 1-pole Socket P2RF-05-S P2RF-08-S Clip & Release Lever P2CM-S Nameplate R99-11 nameplate for MY Socket Bridge P2RM-SR, P2RM-SB 2-pole Specifications Item P2RF05S P2RF08S Remarks Relay G2R-1-S Series G2R-2-S Series --- Dimensions (W H D) max. --- Rated voltage 250 VAC --- Rated carry current 10 A at 70 C 5 A at 70 C VDE0627 Applicable wires 0.2 to 1.5 mm 2 (AWG24 to AWG16) --- Solid wire, Standard wire Number of wire connections 2 wires per terminal (1 wire per hole) --- Clamping force 10 N min. (0.2 mm 2 ), 40 N min. (1.5 mm 2 ) EN60999 Safety Standards Standard VDE0627 (IEC664, EN60999) UL508 (UL1059) CSA C22.2 No. 14 (CSA C22.2 No. 158) Approval pending Approval pending Approval pending File No. (status) 3

2 Dimensions P2RF-05-S 38.2 max max. 6 TYP 16.8 TYP Standard model max max (5.3) 61.3 TYP P2RF-08-S 38.2 max max. 6 TYP 16.8 TYP (3.4) Standard model 92.0 max (5.3) 18.0 max TYP 4

3 Terminal Arrangement P2RF-05-S 11 P2RF-08-S Common contacts Make contacts Break contacts A1 A2 Coils A1 A2 Mounting Height (With Lever) P2RF-05-S P2RF-08-S 61.6 TYP TYP (5.30) (5.30) Accessories (Option) Socket Bridge Insulating coating dia. conductor L (See note 1.) Note: 1. The relationship between the model number, the length L, and the color of the insulating coating is shown in the following table. Model number Length L (mm) Color of insulating coating P2RM-SR 14.3 Red P2RM-SB Blue 2. The insulating coating must be able to withstand a voltage of 3,000 V for 1 minute. Use either PE or PA as the material of the insulating coating. 3. The positions of the ends of the insulating coating must not vary more than 0.5 mm. 4. The characteristics of the socket bridge are shown in the following table. Item Characteristic Rated ON current 10 A Rated insulation voltage 250 VAC Temperature rise 35 C max. Dielectric strength 3,000 VAC for 1 minute Ambient operating temperature 55 to 70 C 5

4 Clip and Release Lever 16.8 TYP 6 TYP 40.1 TYP (32.0) 36 TYP 3 TYP (4.0) Installation Tools A flat-blade screwdriver should be used to mount the cables. Applicable Screwdriver Flat-blade, Parallel-tip, 2.5 mm diameter (3.0 mm max.) Flat-blade, Parallel-tip 2.5 dia. (3.0 mm max.) Flat-blade, Flared-tip Examples: FACOM AEF E (AEF. 3 75E) VESSEL No (-) (No (-)3 100) WAGO WIHA 260/ (260/3 50) *Chamfering the tip of the driver improves insertion when used as an exclusive tool. Applicable Wires Applicable Wire Sizes 0.2 to 1.5 mm 2, AWG24 to AWG16 Applicable Wire Type Cannot be used. Solid wires, standard wires, flexible wires, or wires with ferules can be used. (See note 1.) < 2.2 Diameter D (mm) 3.2 (3.5: see note 2.) Conductor diameter d (mm) or length of sides a and b (mm) 1.9 Note: 1. If the overall diameter of the wire is less than 2.2 mm, do not insert the wire past the conductor. Refer to the following diagrams. 2. If the overall diameter of the wire is over 3.2 mm, it will be difficult to use double wiring. Wires with Ferules 6

5 Examples of Applicable Wires (Confirmed Using Catalog Information) Type of wire Conductor type See note 1, above. Recommended wire See note 2, above. sizes Equipment wire 2491X Flexible 0.5, 0.75, 1.0 mm mm 2 BS6004 Solid 0.5 mm 2 Switchgear BS6231 Solid 1.0 mm mm 2 Switchgear BS6231 Flexible 0.5, 0.75 mm mm 2 Tri-rated control and switchgear Flexible 0.5, 0.75, 1.0, 1.5 mm 2 Conduit Standard 1.5 mm 2 UL1007 Flexible 18AWG 16AWG UL1015 Flexible 18AWG, 16AWG UL1061 Flexible 18AWG UL1430 Flexible 18AWG 16AWG Wiring Use wires of the applicable sizes specified above. The length of the exposed conductor should be 8 to 9 mm. 8 to 9 mm Fig. 1 Exposed Conductor Length Use the following wiring procedure. 1. Insert the specified screwdriver into the release hole located beside the wire connection hole where the wire is to be inserted. Fig. 3 Section A-A of Fig. 2 Wire connection hole Release hole Screwdriver Insert Wire connection holes 2. Insert the exposed conductor into the wire connection hole. Release holes Insert Fig. 2 Wire Connection Holes and Release Holes 3. Pull out the screwdriver. Pull out 7

6 Precautions Precautions for Connection Do not move the screwdriver up, down, or from side to side while it is inserted in the hole. Doing so may cause damage to internal components (e.g., deformation of the clamp spring or cracks in the housing) or cause deterioration of insulation. Do not insert the screwdriver at an angle. Doing so may break the side of socket and result in a sort-circuit. Do not insert two or more wires in the hole. Wires may come in contact with the spring causing a temperature rise or be subject to sparks. (There are two wiring holes for each terminal.) General Precautions Use the clip to prevent relays floating or falling out of the socket. Do not use the product if it has been dropped on the ground. Dropping the product may adversely affect performance. Confirm that the socket is securely attached to the mounting track before wiring. If the socket is mounted insecurely it may fall and injure the operator. Ensure that the socket is not charged during wiring and maintenance. Not doing so may result in electric shock. Do not pour water or cleansing agents on the product. Doing so may result in electric shock. Do not use the socket in locations subject to solvents or alkaline chemicals. Do not use the socket in locations subject to ultraviolet light (e.g., direct sunlight). Doing so may result in markings fading, rust, corrosion, or resin deterioration. Do not dispose of the product in fire. Removing from Mounting Rail To remove the socket from the mounting rail, insert the tip of screwdriver in the fixture rail, and move it in the direction shown below. Insert the screwdriver along the hole wall as shown below. Screwdriver If lubricating liquid, such as oil, is present on the tip of screwdriver, the screwdriver may fall out resulting in injury to the operator. Insert the screwdriver into the bottom of the hole. It may not be possible to connect cables properly if the screwdriver is inserted incorrectly. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by To convert grams into ounces, multiply by Cat. No. J132-E1-01 OMRON Corporation Electronic Components Company In the interest of product improvement, specifications are subject to change without notice. Electronic & Mechanical Components Division H.Q. General Purpose Relay Division Shiokoji Horikawa, Shimogyo-ku Kyoto, Japan Tel: (81) /Fax: (81) Printed in Japan M (0302) (O) 8