Interface RF Connector with Switch

Transcription

1 NEW Interface RF onnector with Switch Series Overview Designed for end user applications requiring redirection of transmission from internal built-in antenna to the external antenna. Small size, lightweight and high reliability makes it ideal for use in.4 Hz band wireless Large rea Networks applications. Plug can be rotated after full insertion. Features. onfirmation of complete connection uilt-in interlock feature confirms fully mated condition with a "click" sensation.. Non-directional connection The connector can be mated in any position on a 36 axis and can rotate within the same when in use, allowing routing of the connected cable in any direction. 3. High durability uaranteed 5 insertion/removal cycles. 4. Space-saving The external dimensions of the board-mounted receptacle (5. mm high, 6.5 mm wide, 7. mm deep) makes it ideal for use in small devices. 5. Ease of connection and handling Over-molded plug, with convenient grip and built-in cable strain relief assures reliable mating/un-mating by end user. 6. Designed for board placement with automatic equipment Top surface of receptacle assembly is flat, allowing reliable hold for vacuum nozzles of automatic placement equipment. pplications PS terminals, wireless LN modules, notebook computers, PD, and other high frequency equipment. (Page 7 lists applications and antenna circuit switching examples.) Receptacle Plug -(LP) SM onversion dapter For Receptacle: SM onversion dapter For Plug: -(LP) MS5P-HRMJ MS5J-HRMJ 3.8

2 Product Specifications Frequency range D to 3Hz Operating temperature range -4ç to +85ç Power rating 4W Not mated with the plug Open(--(LP)) D to Hz.d Hz to Hz.4d Hz to 3 Hz.7d D to Hz.d.3d Insertion loss Hz to Hz.4d.5d Hz to 3 Hz.6d.d D to Hz d min. Isolation loss Hz to Hz d min. Hz to 3 Hz d min.. ontact resistance. Insulation resistance 3. Withstanding voltage 4. Vibration 5. Shock 6. Temperature cycle 7. Humidity 7. (Steady state) 8. Salt spray Item Specification onditions 9. Mating/un-mating forces. Durability. (insertion/ withdrawal) Materials 5 m ohms M ohms min. No flashover or insulation breakdown No electrical discontinuity of µ s or more No electrical discontinuity of µ s or more ontact resistance: m ohms Insulation resistance: M ohms min. ontact resistance: m ohms Insulation resistance: M ohms min. ontact resistance: m ohms No corrosions Mating: N Un-mating: 3 min. ontact resistance: m ohms m V D V / minute Frequency: to 5 Hz, single amplitude of.75 mm, acceleration of 98 m/s for hours in each of the 3 directions cceleration of 49 m/s, ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis Temperature: -55ç / +5ç to +35ç / +85ç / +5ç to +35ç Time: 3 / to 3 / 3 / to 3(Minutes) cycles 96 hours at temperature of 4ç and humidity of 9% 5% salt water solution, 48 hours With corresponding connector 5 cycles Receptacle Part Material Finish Insulator Polyamide (UL 94V-) Lock mating section Stainless steel Nickel plating (Termination area: tin-lead plated) Outer conductor shell Phosphor bronze Nickel plating (Termination area: tin-lead plated) ontact Phosphor bronze old plating ontact eryllium copper old plating Plug -(LP) Part Material Finish over P over P Ring Stainless steel Nickel plating Outer conductor shell Phosphor bronze Nickel plating Inner contact Phosphor bronze old plating Insulator Polyamide (UL 94-H) Ferrule Stainless steel rimp metal fitting rass Nickel plating ushing Polyester

3 High Frequency haracteristics (Typical) NORMLLY LOSED(N.O) ~ (Not mated with the plug) : SPE : INSERTION LOSS SPE : ISOLTION SPE INSERTION LOSS [d] INSERTION LOSS D.. 3. [Hz] OPEN(N.O) ~ (Mated with the plug) INSERTION LOSS [d] INSERTION LOSS ISOLTION [d] ISOLTION. D.. 3. [Hz] 3

4 Receptacle MS_ (.5) Ø M () , pieces per reel pieces ircuit diagram Not mated with the plug(n.) Mated with the plug(n.o) P mounting pattern -Ø.(Throug hole) onnector front edge Ø(Land) Ø No conductive traces 4

5 Specifications Ø Embossed tape reel packaging (, pieces/reel) Ø3 Unreeling direction 6.4 Ø8 7.5 Ø Ø38 6 Unreeling direction 7.4 Recommended Temperature Profile Temperature (ç) 35 sec. Maximum temperature Peak temperature duration Peak temperature ç min. : 4ç : sec. Max. : ç to 35ç : 5 sec. Max. 5ç to 6ç : 4 sec. Min sec. min. 5sec. 5 Time (sec.) 5

6 Plug (4.) (8) * Dedicated termination tools required. * an be supplied terminated with cable. (5.5) (.5) (Ø4.5) pplicable cable -(LP) DS-QEHV(T) or UL.5DL.5DS-QEHV(T) Termination fixture: /F-MD, /SO-MD, /E-MP and /K-MP Please contact your Hirose Electric representative for information. SM onversion adaptors For Receptacle: /4-36UNS- Ø7.3 Ø (6.9) MS5P-HRMJ For Plug: -(LP) /4-36UNS- Ø7.3 Ø (6.9) MS5J-HRMJ

7 pplications Notebook P's, PD's, PS terminals, wireless communications equipments. PS Note P PD ntenna ircuit Re-directing Notebook P with inner antenna for wireless LN Outer antenna for wireless LN Receptacle Plug -(LP) Re-direct from inner antenna to outer antenna Not mated with the plug (N.) Mated with the plug (N.O) 7