Connectors according to DIN / IEC
|
|
|
- Gillian Clark
- 7 years ago
- Views:
Transcription
1 78 Connetors ording to DIN / IEC
2 Tehnil spei tions 80 Derting digrms 81 Hole spei tions 82 Tehnil informtion 83 Type B 84 Type B/2 88 Type B/3 92 Type C 96 Type C/2 100 Type C/3 104 Type M 108 Type M/2 112, 113 Type M/3 112, 113 Type R 114 Type R/2 118 Type R/3 122 Type D 126 Type E 129 Type F 132 Type F low pro le 136 Type G 138, 140 Type G low pro le 139 Type H Type H11 low pro le 144 Type H15 145, 146 Type H15 low pro le 147 Type H7/F Type H7/F24 low pro le 150 Type VME 64x 152 Aessories: Shroud VME 153 Swithing onnetor 154 IDC: Types B nd C, tehnil spei tions 156 Aessories: Shroud 158 Additionl informtion: Bord lok 159 Additionl informtion: Coding 160 Additionl informtion: Pre-mting/lte-mting ontts 161 Fx request 162 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 79
3 Tehnil spei tions Tehnil spei tions Types ording to IEC B, B/2, B/3 C, C/2, C/3 D E F G H VME 64x Inverted type R, R/2, R/3 Mximum no. of ontts 64/32/20 96/48/ Contt row designtion of z d e z d z d f z d mle nd femle onnetors z d Operting temperture rnge 55 C to C 65 C to C 55 C to C Creepge (K) nd lerne (L) in mm Within row Between the rows K 1.2 mm 3.0 mm 3.0 mm 3.0 mm 8.0 mm 8.0 mm L 1.2 mm 3.0 mm 1.6 mm 1.6 mm 4.5 mm 4.5 mm K 1.2 mm 3.0 mm 3.0 mm 3.0 mm 8.0 mm 8.0 mm L 1.2 mm 3.0 mm 1.6 mm 1.6 mm 4.5 mm 4.5 mm I See digrms on pge 81 Mx. operting urrent t + 20 C 1.5 A 5.6 A 15 A 1.5 A mient temperture + 70 C 1.1 A 4.0 A 11 A 1.1 A C 0.7 A 2.5 A 8 A 0.7 A Test voltge, 50 Hz, 1 minute Contt/ontt V rms 1000 V 1550 V 1550 V 1550 V 3100 V 1000 V Contt/ground V rms 1550 V 1550 V 2500 V 2500 V 3100 V 1550 V Contt resistne R < 20 m < 15 m < 8 m 20 m < 30 m Insultion resistne R > 10 6 M 10 4 M Durility ording to DIN EN Engging nd seprting fore for the omplete, fully equipped onnetor F 64 ontts < 60 N 96 ontts < 90 N 32 ontts < 30 N 48 ontts < 45 N 20 ontts < 18 N 30 ontts < 28 N Performne level I = 500 mting yles 500 mting yles Performne level II = 400 mting yles 250 mting yles Performne level III = 50 mting yles < 40 N < 60 N < 75 N < 100 N < 80 N < 90 N 160 N Seprting fore per ontt (test mesuring devie) Design femle ontt Insultor mteril F > 0.15 N > 0.2 N > 0.15 N Doule ontt PBT glss lled, UL 94 V-0 PC er-glss reinfored, not omustile. to UL 94 V-1 PA glss lled, UL 94 V-0 Environment/pprovls RoHS omplint/ul ( le: E130314) * Note on press- t tehnology: Printed iruit ords with me protetion FR-4 or FR-6 re permissile up to temperture of 115 C. The press- t stndrd IEC only spei es the press- t onnetion up to n working temperture of 85 C. For working tempertures tht exeed 85 C, it is reommended tht the press- t onnetion is quli ed pplition-spei y ept. 80 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
4 Derting digrms Derting digrms Current rrying pity (Ampere) Current rrying pity (Ampere) Current rrying pity (Ampere) Amient temperture C Amient temperture C Amient temperture C Type B, C, R 20 C 1.5 A 70 C 1.1 A 100 C 0.7 A Type D, E, F, G 20 C 5.6 A 70 C 4.0 A 100 C 2.5 A Type H11 20 C 15 A 70 C 11 A 100 C 8 A ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 81
5 Hole spei tions Hole spei tions Plted through-hole ording to IEC ept offers dpted press- t zones for vrious new ord surfes. C femle onnetor Speil version B/C/R/M/F low pro le/ G low pro le/vme64x D/E/F/G Nominl hole Ø 0.85 mm Ø 1.0 mm Ø 1.6 mm imm. Sn printed iruit ords A PCB thikness min. 1.6 mm min. 1.6 mm min. 1.6 mm B Plted hole Ø / 0.00 mm Ø / 0.00 mm Ø / 0.00 mm C Drill hole 1.0 ± mm 1.15 ± mm 1.75 ± mm D Cu plting min. 25 m min. 25 m min. 25 m E imm. Sn plting mx. 1.5 m mx. 1.5 m mx. 1.5 m F Annulr ring min. 0.1 mm min. 0.1 mm min. 0.1 mm Ni, Au printed iruit ords A PCB thikness min. 1.6 mm min. 1.6 mm min. 1.6 mm B Plted hole Ø / 0.00 mm Ø / 0.00 mm Ø / 0.00 mm C Drill hole 1.0 ± mm 1.15 ± mm 1.75 ± mm D Cu plting min. 25 m min. 25 m min. 25 m E Ni, Au plting m Au more thn m Ni m Au more thn m Ni m Au more thn m Ni F Annulr ring min. 0.1 mm min. 0.1 mm min. 0.1 mm pure Cu printed iruit ords A PCB thikness min. 1.6 mm min. 1.6 mm min. 1.6 mm B Plted hole Ø / 0.00 mm Ø / 0.04 mm Ø / 0.07 mm C Drill hole 1.0 ± mm 1.15 ± mm 1.75 ± mm D Cu plting min. 25 m min. 25 m min. 25 m E OSP* e. g. GLICOAT-SMD (F2) with m e. g. GLICOAT-SMD (F2) with m e. g. GLICOAT-SMD (F2) with m F Annulr ring min. 0.1 mm min. 0.1 mm min. 0.1 mm HAL Sn printed iruit ords A PCB thikness min. 1.6 mm min. 1.6 mm min. 1.6 mm B Plted hole Ø / 0.02 mm Ø / 0.06 mm Ø 1.6 ± 0.09 mm C Drill hole 1.0 ± mm 1.15 ± mm 1.75 ± mm D Cu plting min. 25 m min. 25 m min. 25 m E HAL Sn 5 15 m 5 15 m 5 15 m F Annulr ring min. 0.1 mm min. 0.1 mm min. 0.1 mm * OSP = Orgni Solderiltity Preservtives 82 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
6 Tehnil informtion Tehnil informtion For onnetors ording to DIN / IEC (DIN onnetors), ept offers three Tom press press- t zone vrints for different printed iruit ord thiknesses. Prt numers key Type PCB thikness 1.5 to 2.0 mm PCB thikness 2.0 to 2.8 mm PCB thikness > 2.8 mm B, B/2, B/3 (femle onnetors) C, C/2, C/3 (femle onnetors) 102-xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx-03 Hole dimeter 0.85 mm In ddition to the 1.0 stndrd hole, for the DIN types B nd C femle onnetors Tom press press- t zone for the 0.85 mm hole is ville. This provides more spe etween two plted-through holes nd there n e n dditionl iruit etween the drill holes. Prt numers key for 0.85 mm Tom press on request Type B, B/2, B/3 (femle onnetors) C, C/2, C/3 (femle onnetors) Prt numer 002-xxxxx-xx 004-xxxxx-xx Tom press 1.0 mm/0.85 mm PCB hole 1.0 mm PCB hole 0.85 mm ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 83
7 Type B Mle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 206) Support tool (see pge 207) Coding essories (see pge 160) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Contt rrngement (see pge 162) 84 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
8 Type B Mle onnetor Solder tehnology Performne level II Termintion length THTR* Performne level II ontts Contt rrngement Prt numer TH TH Aessories Coding essories (see pge 160) Note * THTR (Through Hole Tehnology Re ow) Performne levels I + III or ustomer-spei Speil ontt length Other termintion lengths in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 85
9 Type B Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer xx xx xx Aessories Press- t tool (see pge 208) Support tool (see pge 209) Coding essories (see pge 160) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Alterntive surfe Sn, e. g. for WireWrp Ordering note Only for 102 PCB 1.5 to 2.0 mm = xxx-xxxxx-01 with termintion length = 3.2 mm PCB 2.0 to 2.8 mm = xxx-xxxxx-02 with termintion length = 4.6 mm PCB > 2.8 mm = xxx-xxxxx-03 with termintion length = 4.6 mm Without nge Contt rrngement (see pge 162) Cross referene Type B with IDC (see pge 156) 86 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
10 Type B Femle onnetor Solder tehnology Performne level II Termintion length Mnul soldering with solder lug ontts Contt rrngement Prt numer in THTR* TH in THTR* TH in THTR* TH Aessories Coding essories (see pge 160) Cross referene Type B with IDC (see pge 156) Performne levels I + III or ustomer-spei Speil ontt length Other termintion lengths in THTR Note * THTR (Through Hole Tehnology Re ow) Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 87
11 Type B/2 Mle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 206) Support tool (see pge 207) Coding essories (see pge 160) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Contt rrngement (see pge 162) 88 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
12 Type B/2 Mle onnetor Solder tehnology Performne level II Termintion length THTR* Performne level II ontts Contt rrngement Prt numer TH TH Aessories Coding essories (see pge 160) Note * THTR (Through Hole Tehnology Re ow) Performne levels I + III or ustomer-spei Speil ontt length Other termintion lengths in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 89
13 Type B/2 Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer xx xx xx xx xx xx Aessories Press- t tool (see pge 208) Support tool (see pge 209) Coding essories (see pge 160) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Alterntive surfe Sn, e. g. for WireWrp Ordering note PCB 1.5 to 2.0 mm = xxx-xxxxx-01 with termintion length = 3.2 mm PCB 2.0 to 2.8 mm = xxx-xxxxx-02 with termintion length = 4.6 mm PCB > 2.8 mm = xxx-xxxxx-03 with termintion length = 4.6 mm Without nge Contt rrngement (see pge 162) 90 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
14 Type B/2 Femle onnetor Solder tehnology Performne level II Termintion length Mnul soldering with solder lug ontts Contt rrngement Prt numer Aessories Coding essories (see pge 160) Performne levels I + III or ustomer-spei Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 91
15 Type B/3 Mle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 206) Support tool (see pge 207) Coding essories (see pge 160) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Contt rrngement (see pge 162) 92 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
16 Type B/3 Mle onnetor Solder tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Coding essories (see pge 160) Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 93
17 Type B/3 Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer xx xx xx Aessories Press- t tool (see pge 208) Support tool (see pge 209) Coding essories (see pge 160) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Alterntive surfe Sn, e. g. for WireWrp Ordering note PCB 1.5 to 2.0 mm = xxx-xxxxx-01 with termintion length = 3.2 mm PCB 2.0 to 2.8 mm = xxx-xxxxx-02 with termintion length = 4.6 mm PCB > 2.8 mm = xxx-xxxxx-03 with termintion length = 4.6 mm Without nge Contt rrngement (see pge 162) 94 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
18 Type B/3 Femle onnetor Solder tehnology Performne level II Termintion length Mnul soldering with solder lug ontts Contt rrngement Prt numer Aessories Coding essories (see pge 160) Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 95
19 Type C Mle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 206) Support tool (see pge 207) Coding essories (see pge 160) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Contt rrngement (see pge 162) 96 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
20 Type C Mle onnetor Solder tehnology Performne level II Termintion length THTR* Performne level II ontts Contt rrngement Prt numer TH TH TH TH Aessories Coding essories (see pge 160) Note * THTR (Through Hole Tehnology Re ow) Performne levels I + III or ustomer-spei Speil ontt length Other termintion lengths in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 97
21 Type C Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length Contt ontts rrngement Prt numer xx xx xx Note * Rer mting zone performne level II xx xx xx Without nge Contt rrngement (see pge 162) Cross referene Type C with swithing funtion (see pge 155) VMEx (see pge 152) Type C with IDC (see pge 157) Aessories Press- t tool (see pge 208) Support tool (see pge 209) Coding essories (see pge 160) Shroud (see pge 158) Performne levels I + III or ustomer-spei Speil ontt length Alterntive surfe Sn, e. g. for WireWrp Ordering note Only for 104 PCB 1.5 to 2.0 mm = xxx-xxxxx-01 with termintion length = 3.2 mm PCB 2.0 to 2.8 mm = xxx-xxxxx-02 with termintion length = 4.6 mm PCB > 2.8 mm = xxx-xxxxx-03 with termintion length = 4.6 mm 98 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
22 Type C Femle onnetor Solder tehnology Performne level II Termintion length Mnul soldering with solder lug ontts Contt rrngement Prt numer in THTR* TH in THTR* TH in THTR* TH in THTR* TH in THTR* TH in THTR* TH Aessories Coding essories (see pge 160) Cross referene Type C with swithing funtion (see pge 155) VMEx (see pge 152) Type C with IDC (see pge 157) Performne levels I + III or ustomer-spei Speil ontt length Other termintion lengths in THTR Note * THTR (Through Hole Tehnology Re ow) Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 99
23 Type C/2 Mle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 206) Support tool (see pge 207) Coding essories (see pge 160) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Contt rrngement (see pge 162) 100 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
24 Type C/2 Mle onnetor Solder tehnology Performne level II Termintion length THTR* Performne level II ontts Contt rrngement Prt numer TH TH TH Aessories Coding essories (see pge 160) Note * THTR (Through Hole Tehnology Re ow) Performne levels I + III or ustomer-spei Speil ontt length Other termintion lengths in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 101
25 Type C/2 Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer xx xx xx Aessories Press- t tool (see pge 208) Support tool (see pge 209) Coding essories (see pge 160) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Alterntive surfe Sn, e. g. for WireWrp Ordering note Only for 104 PCB 1.5 to 2.0 mm = xxx-xxxxx-01 with termintion length = 3.2 mm PCB 2.0 to 2.8 mm = xxx-xxxxx-02 with termintion length = 4.6 mm PCB > 2.8 mm = xxx-xxxxx-03 with termintion length = 4.6 mm Without nge Contt rrngement (see pge 162) 102 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
26 Type C/2 Femle onnetor Solder tehnology Performne level II Termintion length Mnul soldering with solder lug ontts Contt rrngement Prt numer Aessories Coding essories (see pge 160) Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 103
27 Type C/3 Mle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 206) Support tool (see pge 207) Coding essories (see pge 160) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Without nge Contt rrngement (see pge 162) 104 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
28 Type C/3 Mle onnetor Solder tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Coding essories (see pge 160) Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 105
29 Type C/3 Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 208) Support tool (see pge 209) Coding essories (see pge 160) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Alterntive surfe Sn, e. g. for WireWrp Without nge Contt rrngement (see pge 162) 106 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
30 Type C/3 Femle onnetor Solder tehnology Performne level II Termintion length Mnul soldering with solder lug ontts Contt rrngement Prt numer Aessories Coding essories (see pge 160) Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 107
31 Type M for speil ontts ording to DIN Femle onnetor 94.9 Similr drwing 3x7.62= x2.54=17.78 Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer 6/ / / / / ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
32 Type M for speil ontts ording to DIN Femle onnetor Performne levels I + III or ustomer-spei Speil ontt length Press- t tool Support tool Note Femle onnetors must e srewed or riveted onto the printed iruit ord t the nge ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 109
33 Type M for speil ontts in press- t tehnology Femle onnetor 94.9 Similr drwing 3x7.62= x2.54=17.78 Press- t tehnology Performne level II Termintion length Speil ontt is not pre-loded Speil ontt is pre-loded ontts Contt rrngement Prt numer 6/ / / / / ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
34 Type M for speil ontts in press- t tehnology Femle onnetor Performne levels I + III or ustomer-spei Speil ontt length Press- t tool Support tool Contt rrngement of the speil ontts Note Femle onnetors must e srewed or riveted onto the printed iruit t the nge ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 111
35 Type M/2, M/3 for speil ontts ording to DIN Femle onnetor M/2 M/3 Hole pttern Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer M/2 30/ M/3 12/ Performne levels I + III or ustomer-spei Speil ontt length Press- t tool Support tool Note Femle onnetors must e srewed or riveted onto the printed iruit t the nge 112 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
36 Type M/2, M/3 for speil ontts in press- t tehnology Femle onnetor Press- t tehnology Performne level II Termintion length Speil ontt is not pre-loded Speil ontt is pre-loded ontts Contt rrngement Prt numer M/2 30/ M/3 12/ Performne levels I + III or ustomer-spei Speil ontt length Press- t tool Support tool Contt rrngement of the speil ontts Note Femle onnetors must e srewed or riveted onto the printed iruit t the nge ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 113
37 Type R Mle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 206) Support tool (see pge 207) Shroud (see pge 158) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Alterntive surfe Sn, e. g. for WireWrp Contt rrngement (see pge 162) 114 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
38 Type R Mle onnetor Solder tehnology Performne level II Termintion length Mnul soldering with solder lug THTR* Performne level II ontts Contt rrngement Prt numer TH TH TH TH TH TH TH TH Performne levels I + III or ustomer-spei Speil ontt length Other termintion lengths in THTR Note * THTR (Through Hole Tehnology Re ow) Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 115
39 Type R Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 210) Support tool (see pge 211) Performne levels I + III or ustomer-spei Speil ontt length Without nge Contt rrngement (see pge 162) 116 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
40 Type R Femle onnetor Solder tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 117
41 Type R/2 Mle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 206) Support tool (see pge 207) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Alterntive surfe Sn, e. g. for WireWrp Contt rrngement (see pge 162) 118 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
42 Type R/2 Mle onnetor Solder tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 119
43 Type R/2 Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 210) Support tool (see pge 211) Performne levels I + III or ustomer-spei Speil ontt length Without nge Contt rrngement (see pge 162) 120 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
44 Type R/2 Femle onnetor Solder tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 121
45 Type R/3 Mle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 206) Support tool (see pge 207) Note * Rer mting zone performne level II Performne levels I + III or ustomer-spei Speil ontt length Alterntive surfe Sn, e. g. for WireWrp Contt rrngement (see pge 162) 122 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
46 Type R/3 Mle onnetor Solder tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 123
47 Type R/3 Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 210) Support tool (see pge 211) Performne levels I + III or ustomer-spei Speil ontt length Without nge Contt rrngement (see pge 162) 124 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
48 Type R/3 Femle onnetor Solder tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 125
49 Type D Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Press- t tool (see pge 208) Support tool (see pge 209) Coding essories (see pge 160) Performne levels I + III or ustomer-spei Speil ontt length Without nge Contt rrngement (see pge 162) 126 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
50 Type D Femle onnetor Solder tehnology Performne level II Termintion length Mnul soldering with solder lug ontts Contt rrngement Prt numer Aessories Coding essories (see pge 160) Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 127
51 Type D Mle onnetor Hole pttern Solder tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Coding essories (see pge 160) Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) 128 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
52 Type E Mle onnetor Hole pttern Solder tehnology Performne level II Termintion length ontts Contt rrngement Prt numer 32 e e e Aessories Coding essories (see pge 160) Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 129
53 Type E Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer 32 e e e Aessories Press- t tool (see pge 208) Support tool (see pge 209) Coding essories (see pge 160) Performne levels I + III or ustomer-spei Speil ontt length Without nge Contt rrngement (see pge 162) 130 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
54 Type E Femle onnetor Solder tehnology Performne level II Termintion length Mnul soldering with solder lug ontts Contt rrngement Prt numer 32 e e e Aessories Coding essories (see pge 160) Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 131
55 Type F Mle onnetor Bohrungen für Codierstifte hole enter for polriztion pin Hole pttern Solder tehnology Performne level II Termintion length ontts Contt rrngement Prt numer 32 d z d z d z ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I
56 Type F Mle onnetor Aessories Coding essories (see pge 160) Performne levels I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Contt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-mil sles@ept.de I 133
57 Type F Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement 32 d z Prt numer z d z d Aessories Press- t tool (see pge 208) Support tool (see pge 209) Coding essories (see pge 160) Performne level I + III or ustomer-spei Speil ontt length Speil ontt rrngement (see pge 162) 134 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
58 Type F Femle onnetor Solder tehnology Performne level II Termintion length Mnul soldering with solder lug ontts Contt rrngement 32 d z Ø Prt numer z d z d Aessories Coding essories (see pge 160) Performne level I + III or ustomer-spei Speil ontt length Also in THTR Speil ontt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 135
59 Type F low pro le Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement 32 d z Prt numer z d z d Aessories Press- t tool (see pge 208) Support tool (see pge 209) Coding essories (see pge 160) Note * Rer mting zone performne level II Performne level I + III or ustomer-spei Speil ontt length Without nge Speil ontt rrngement (see pge 162) 136 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
60 Type F low pro le Femle onnetor Solder tehnology Performne level II Termintion length ontts Contt rrngement 32 d z Prt numer z d z d Aessories Coding essories (see pge 160) Performne level I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Speil ontt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 137
61 Type G Mle onnetor Hole pttern Solder tehnology Performne level II Termintion length ontts Pre-mting ontt t position Contt rrngement Prt numer 64 Without f d 64 Z z Z 2 nd Z Aessories Coding essories (see pge 160) Performne level I + III or ustomer-spei Also in THTR Bord lok (see pge 159) Speil ontt rrngement (see pge 162) 138 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
62 Type G low pro le Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer 64 z d f Aessories Press- t tool (see pge 208) Support tool (see pge 209) Coding essories (see pge 160) Performne level I + III or ustomer-spei Speil ontt length Without nge Speil ontt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 139
63 Type G Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer 64 z d f Aessories Press- t tool (see pge 208) Support tool (see pge 209) Coding essories (see pge 160) Performne level I + III or ustomer-spei Speil ontt length Without nge Speil ontt rrngement (see pge 162) 140 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
64 Type G Femle onnetor Solder tehnology Performne level II Termintion length Mnul soldering with solder lug Ø ontts Contt rrngement Prt numer 64 z d f Aessories Coding essories (see pge 160) Performne level I + III or ustomer-spei Speil ontt length Also in THTR Bord lok (see pge 159) Speil ontt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 141
65 Type H11 Mle onnetor Hole pttern Solder tehnology Performne level II Termintion length Pre-mting ontts ontt t position Contt rrngement Prt numer 11 Without ; Aessories Coding essories (see pge 160) 142 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
66 Type H11 Femle onnetor Hole pttern Fston Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Coding essories (see pge 160) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 143
67 Type H11 low pro le Femle onnetor Hole pttern Solder tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Aessories Coding essories (see pge 160) 144 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
68 Type H15 Mle onnetor Hole pttern Solder tehnology Performne level II Termintion length Pre-mting ontts ontt t position Contt rrngement Prt numer 15 Z Z 4 nd Z Bord lok (see pge 159) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 145
69 Type H15 Femle onnetor Hole pttern Fston Performne level II Termintion length ontts Contt rrngement Prt numer Bord lok (see pge 159) Aessories Coding essories (see pge 160) 146 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
70 Type H15 low pro le Femle onnetor Hole pttern Solder tehnology Performne level II Termintion length Mnul soldering with solder lug ontts Contt rrngement Prt numer Bord lok (see pge 159) Aessories Coding essories (see pge 160) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 147
71 Type H7/F24 Mle onnetor Hole pttern Solder tehnology Performne level II Termintion length Pre-mting ontts ontt t position Contt rrngement Prt numer d 7+24 Z 32 z Bord lok (see pge 159) 148 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
72 Type H7/F24 Femle onnetor Hole pttern Solder tehnology Performne level II Termintion length ontts Contt rrngement Prt numer Ø 16 d z z d z d Performne level I + III or ustomer-spei Speil ontt length Also in THTR Crimp ontts Speil ontt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 149
73 Type H7/F24 low pro le Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts Contt rrngement Prt numer 7+16 z d z d z d Performne level I + III or ustomer-spei Speil ontt length Crimp ontts Press- t tool Support tool Without nge Speil ontt rrngement 150 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
74 Type H7/F24 low pro le Femle onnetor Solder tehnology Performne level II Termintion length ontts Contt rrngement Prt numer 7+16 z d z d z d Performne level I + III or ustomer-spei Speil ontt length Also in THTR Crimp ontts Bord lok (see pge 159) Speil ontt rrngement (see pge 162) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 151
75 Connetors ording to DIN / IEC Type VME 64x Femle onnetor Hole pttern Press- t tehnology Performne level I Termintion length ontts Contt rrngement Prt numer 160 z d z d z d Aessories Press- t tool (see pge 208) Support tool (see pge 209) Shroud (see pge 153) Performne level II + III or ustomer-spei Speil ontt length Note * Rer mting zone performne level I 152 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
76 Aessories Shroud VME x 2.54 = X A Ø A 31 x 2.54 = Hole pttern Prt numer PCB thikness X Post length VME mm 6.0 mm 17 mm mm 4.8 mm 17 mm Different designs nd speil types ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 153
77 Additionl informtion Swithing onnetors Swithing onnetors femle onnetor with integrted swithes Prolem A priniple often used for different us systems is the looping-through of signl lines vi module ords, the so-lled disy hining. Module plugged-in Disy hin Signl line Module not plugged-in Jumper plugged-in Module plugged-in This disy hining, however, leds to new prolem, whih eomes ovious when one of the modules is pulled from the system: The disy hin signl onnetion is roken nd must e re-estlished using jumpers. This is not esy s the modules re loted lose to eh other in the rk. More often lrge prt of the housing must e tken prt or the whole endevour of pling the jumper on the orret pins results in nerve-wrking fumling. Mistkes nd therefore mispositionings n hppen. A possile solution The integrtion of swithes into stndrd onnetor ording to IEC , e. g. into femle onnetor type C, is simple nd elegnt solution for the prolem desried. The ontt springs of this C femle onnetor were extended y wing-like ontt ts. A gold-plted metl disk is loted etween the ontt springs. In rest position, with the mle onnetor not plugged-in, the djent ontt springs re short-iruited through pling of the ontt ts on the metl disk. With the mle onnetor plugged-in, the ontt springs re seprted from eh other through the ontt pins of the mle onnetor. The ontt ts of the spring re lifted off the metl disk. This interrupts the onnetion etween the two springs. Due to the swithing ehvior of the C femle onnetor, the disy hin onnetion is utomtilly losed when the module ord is pulled out. Funtion-wise the losed swithing ontt etween two ontt springs orresponds to jumper utomtilly eing plugged in when the mle onnetor is pulled out. Applition in the VME us The disy hining priniple is used for the IACK nd BG signl lines in the VME us. By integrting swithing funtion t the positions of the respetive signl lines in the onnetor, the jumpers used so fr re no longer required. Further pplitions The integrted swithing funtion is not restrited to the positions in the C femle onnetor stted ove. A swith n e integrted etween ny positions in the, nd rows of C femle onnetor IEC nd/or etween the nd rows of C femle onnetor IEC A further pplition for ept swithing onnetors re e. g. network onentrtors (hus). In this pplition, too, the disy hining is rried out fully utomtilly vi ustomer-spei swithing onnetors. Funtionl priniple of the swithing onnetors View from the side Swithing ontts in rows 2 4 View from the top Swithing priniple 1 3 Swithing ontts ross rows ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
78 Swithing onnetor Femle onnetor Hole pttern Press- t tehnology Performne level II Termintion length ontts 96 Swithing ontts t position 21 22, 4 5, 6 7, 8 9, for VME Prt numer xx xx xx 96 1, 2, 3, 4,, xx xx xx Aessories Press- t tool (see pge 208) Support tool (see pge 209) Coding essories (see pge 160) Note * Rer mting zone performne level II Performne level I + III or ustomer-spei Speil termintion length Ordering note PCB 1.5 to 2.0 mm = xxx-xxxxx-01 with termintion length = 3.2 mm PCB 2.0 to 2.8 mm = xxx-xxxxx-02 with on request PCB > 2.8 mm = xxx-xxxxx-03 with termintion length = 4.6 mm Without nge Speil ontt rrngement (see pge 162) Customer-spei swithing ridge positions (see pge 163) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 155
79 IDC: type B nd tehnil spei tions Femle onnetor IDC Performne level II ontts Contt rrngement Prt numer Strin relief rket Rion le Also ville in solder/press- t tehnology (see pge 86) Tehnil spei tions IDC Connetions IDC Insultor mteril Polyester, self-extinguishing UL 94 V0 Temperture rnge 55 C to C Cpity pprox pf Opertionl urrent 1 A t 20 C Opertionl voltge Test voltge Contt resistne Insultion resistne Environment 220 V, 50 Hz 500 V/1.27 mm; 350 V/0.84 mm 30 m 10 6 M RoHS omplint 156 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
80 IDC: type C Femle onnetor IDC Performne level II ontts Contt rrngement Prt numer Strin relief rket Rion le Also ville in solder/press- t tehnology (see pge 98) ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 157
81 Aessories Shroud Hole Hole pttern Prt numer PCB thikness Post length C/R with nut C/R C/R self-retining C/R self-retining without nge mm mm mm mm Different designs nd speil types 158 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
82 Additionl informtion Bord lok Bord lok As n lterntive to the rivet nd/or srew fstening of the mle nd/or femle onnetors to the PCBs, onnetors n lso e mounted nd held onto PCBs using ord lok s. The onnetor with the ord lok is pressed onto the PCB to e equipped. The ord loks either lok into ple or re under tension. The onnetions re strong enough to hold the onnetor onto the PCB during the soldering proess. Using plted mounting holes, soldering the ord loks lso essentilly improves the strin relief of the onnetor during insertion nd/or wirhdrwl. Suitle for onnetors with type B, C, D, E, F low pro le, G low pro le femle onnetors nd R mle onnetors Ø Fores Type of insertion Prt numer PCB thikness F m not soldered F h soldered F h xxx-xxxxxc1 1.6 mm Loked < 20 N > 10 N > 25 N xxx-xxxxxc2 2.4 mm Under tension < 20 N > 5 N > 25 N xxx-xxxxxc3 3.6 mm F m : mx. mounting fore per ord lok F h : min. retention fore per ord lok Ordering exmple: C-FL/PCB 1.6 mm, prt numer C1 Suitle for onnetors with type B, C, D, E, F, G mle onnetors nd R femle onnetors Fores Type of insertion Ø Prt numer PCB thikness F m not soldered F h soldered F h xxx-xxxxxc1 1.6 mm Loked < 30 N > 10 N > 20 N xxx-xxxxxc2 2.4 mm Under tension < 30 N > 7.5 N > 20 N xxx-xxxxxc3 3.6 mm F m : mx. mounting fore per ord lok F h : min. retention fore per ord lok Ordering exmple: C-ML/PCB 1.6 mm, prt numer C1 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 159
83 Additionl informtion Coding Coding without loosing ontts Type B nd C The integrted oding of the onnetors with type B nd C prevent tht the wrong modules re plugged in. For oding, oding wedges re inserted into the femle onnetor nd mthing prts re roken out of the insultor mteril of the mle onnertor with oding pliers. Coding Coding str (4 oding wedges) Coding pliers 1) Mle onnetor 2) Femle onnetor 1) Brek-out oding 2) Insert oding wedge into the femle onnetor Prt numer Pkging unit Prt numer strs Type D, E, F nd G With onnetors with type D, E, F nd G holes n e drilled into the mle onnetor nd pins n e inserted into the femle onnetor in mthing positions. Mle onnetors Drill oding hole with guge. Femle onnetors Insert oding pin into the oding hole using the insertion tool. Bore guge Insertion tool Coding pin Prt numer Pkging unit oding pin items Prt numer insertion tool Type H11 nd H15 Keying plug Coding Prt numer ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
84 Additionl informtion Pre-mting nd lte-mting ontts Pre-mting nd lte-mting ontts Type x y x y x y x y x y x y x y For DIN type B, C, R, D, E, F, G The pre-mting ontt n s speil ontt rrngement e inserted into ny desired position. B C R D E F G Type Stndrd (X) Pre-mting (Y) Lte-mting (Y) mm mm mm 0.4 mm 0.8 mm B, B/2, B/3, C, C/2, C/ R, R/2,R/3 Mting side Termintion side D E (grid 2.54 mm) Rows,, e E (grid 5.08 mm) Row F, G Other lengths possile for pre-mting nd lte-mting ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I 161
85 Fx request Fx request Desription of the speil types pre-mting nd/or lte-mting ontts seletive loding Bsi onnetors ording to DIN / IEC : types B, C, R, D, E, F, G Compny Phone First nme Nme Fx Address Signture Estimted quntity required: Numer of required smples: Bsi onnetors ording to the ept tlog ept prt numer: 1/3 1/2 Type B, C, R femle onnetor: B,E Type B, C, R mle onnetor: Connetor side A, B, D, E Rer side A, D, E Type D, E: Femle onnetor Mle onnetor Type F, G mle onnetor: A, B Femle onnetor Mle onnetor C x = Stndrd = 0.8 mm pre-mting d = 0.4 mm lte-mting empty = not loded = 1.0 mm pre-mting e = 0.8 mm lte-mting = 1.3 mm pre-mting f = 1.0 mm lte-mting 162 ept GmH I Phone +49 (0) / I Fx +49 (0) / I E-Mil sles@ept.de I
ERmet ZD Application Note Version 1.1
ERmet ZD Applition Note Version. Generl The ERmet ZD is speiilly esigne or high spee ierentil signling in teleom pplitions t t rtes o up to 5 Git/s. This roust, high perormne, moulr onnetor system is lso
Connectors according to IEC 61076-4-101
Definitions Connectors according to IEC 61076-4-101 The hardmetric connector system ept hm 2.0 was developed and manufactured according to the international standard IEC 61076-4-101. Thus the user can
PC/104, PC/104 -Plus, VarPol connectors
164 PC/104, PC/104 -Plus, VarPol connectors Definitions 166 Technical specifications 168 Hole specifications 169 PC/104 170 PC/104-Plus 172 Accessories: PC/104 and PC/104-Plus 174 VarPol angled pin header
7 mm Diameter Miniature Cermet Trimmer
7 mm Dimeter Miniture Cermet Trimmer A dust seled plsti se proteting qulity ermet trk gurntees high performne nd proven reliility. Adjustments re mde esier y the ler sle redings. is idelly suited to ll
Active Directory Service
In order to lern whih questions hve een nswered orretly: 1. Print these pges. 2. Answer the questions. 3. Send this ssessment with the nswers vi:. FAX to (212) 967-3498. Or. Mil the nswers to the following
INSTALLATION, OPERATION & MAINTENANCE
DIESEL PROTECTION SYSTEMS Exhust Temperture Vlves (Mehnil) INSTALLATION, OPERATION & MAINTENANCE Vlve Numer TSZ-135 TSZ-150 TSZ-200 TSZ-275 TSZ-392 DESCRIPTION Non-eletril temperture vlves mnuftured in
4/3-4/2 Directional valve with solenoid actuation
4/3-4/2 Directionl vlve with solenoid ctution RE 18305-09/12.13 1/10 L511 (LC1-DZ) Size NG6 ISO 4401-03 CETOP RP121 H-03 (CETOP 3) Series 00 Mximum operting pressure 310 r [4500 psi] Mximum flow 50 l/min
Radial blowers with AC motor
Rdil lowers with AC motor Generl informtion Desription 32 Rdil lowers, motor diretly mounted RL, RLF, RLD, RLA, RLE, RLS 33 Rdil lowers with doule housing 37 Rdil lowers, motor deoupled mounted, high temperture
CompactPCI Connectors acc. to PIGMG 2.0 Rev. 3.0
Ctlog E 074486 08/00 Eition ComptPCI Conntors. to PIGMG.0 Rv. 3.0 Gnrl Lt in 999 PCI Inustril Computr Mnufturrs Group (PICMG) introu th nw rvision 3.0 of th ComptPCI Cor Spifition. Vrsion 3.0 of this spifition
Student Access to Virtual Desktops from personally owned Windows computers
Student Aess to Virtul Desktops from personlly owned Windows omputers Mdison College is plesed to nnoune the ility for students to ess nd use virtul desktops, vi Mdison College wireless, from personlly
AP Series Industrial Pushbutton Switch
P Series Features/Benefits IP67 sealed 1,000,000 life cycle Illumination / non-illumination Multiple colored caps Threaded or snap-in mounting Caps available separately RoHS compliant Typical pplications
08. SEK IDC CONNECTORS
. IDC CONNECTORS connectors for flat cables enable simple and, cost-optimized device configuration. connectors are preferably used for connection within the device. HARTING offers a broad range of these
Directory chapter 02 - DIN Power (to 6 A) Types D, E, F, FM, 2F, F9, interface connectors I/U 02. 01. Technical characteristics types D and E... 02.
Directory chapter 02 - () Types D, E, F, FM, 2F, F9, interface connectors I/U Page Technical characteristics types D and E.............................. 02.10 Type D connectors.................... 02.11
MICRO COMBICON Headers for Through Hole Reflow Applications MC(V) 0,5/ G-2,5 THT 2.5 mm Pitch
MICRO COMBICON Heders for Through Hole Reflow Applictions MC(V) 0,5/ G-2,5 THT The consistent use of Through Hole Reflow plug connectors hs lso mde it necessry to extend the COMBICON THR rnge to include
Calculating Principal Strains using a Rectangular Strain Gage Rosette
Clulting Prinipl Strins using Retngulr Strin Gge Rosette Strin gge rosettes re used often in engineering prtie to determine strin sttes t speifi points on struture. Figure illustrtes three ommonly used
Power consumption In operation At rest For wire sizing. Rated impulse voltage Control pollution degree 3. Non-operating temperature
echnicl dt sheet SRF2A-5(-O) Rotry ctutor with emergency function for utterfly vlves orque orue 2 2 2 m m m ominl voltge AC/DC 2 V Control Control Open-close Oen-close SRF2A-5 SRF2A-5 Deenergised C C SRF2A-5-O
4/3-, 4/2- and 3/2- directional valves with switching time adjustment, Model 5-.WE 10 (5-chamber version)
RA 23 351/9.99 RA 23 351/9.99 Replces: 6.98, 8.9 4/3-, 4/2- nd 3/2- directionl vlves with switching time djustment, Model 5-.WE 1 (5-chmer version) Nominl size 1 Series 3X Mximum operting pressure 4569
Power consumption In operation At rest For wire sizing. Auxiliary switch
echnicl dt sheet SRF2A-S2-5(-O) Rotry ctutor with emergency function for utterfly vlves orque orue 2 2 2 m m m ominl voltge AC/DC 2 V Control Control Open-close Oen-close wo integrted uxiliry uiliry switches
Chapter. Contents: A Constructing decimal numbers
Chpter 9 Deimls Contents: A Construting deiml numers B Representing deiml numers C Deiml urreny D Using numer line E Ordering deimls F Rounding deiml numers G Converting deimls to frtions H Converting
4/3, 4/2 directional valves solenoid operated
4/3, 4/2 directionl vlves solenoid operted RE 18303-01/07.12 Replces: RE00157/12.07 1/10 Type L5010 (LC04Z) Size 4 Series 00 Mximum operting pressure 310 r [4500 psi] Mximum flow 25 l/m [6.6 gpm] DVI0003
Solenoid Operated Proportional Directional Control Valve (with Pressure Compensation, Multiple Valve Series)
Solenoid Operted Proportionl Directionl Control Vlve (with Pressure Compenstion, Multiple Vlve Series) Hydrulic circuit (Exmple) v Fetures hese stcking type control vlves show pressure compensted type
Trowel Notch Sizes for Installation of Floor Coverings, Wood Flooring and Tiles
TKB-Tehnil Briefing Note 6 Trowel Noth s for Instlltion of Floor Coverings, Wood Flooring nd Tiles Version: My 2007 Prepred y the Tehnishe Kommission Buklestoffe (TKB) (Tehnil Commission on Constrution
VIESMANN. VITODENS Flue systems for gas condensing boilers 3.8 to 105.0 kw. Technical guide VITODENS FLUE SYSTEMS
VIESMNN VITODENS Flue systems for gs ondensing oilers 3.8 to 105.0 kw Tehnil guide VITODENS FLUE SYSTEMS 5/011 Index Index 1. Flue systems 1.1... 4 Struturl unit... 4 System ertifition... 4 1. Blned flue
Equivalence Checking. Sean Weaver
Equivlene Cheking Sen Wever Equivlene Cheking Given two Boolen funtions, prove whether or not two they re funtionlly equivlent This tlk fouses speifilly on the mehnis of heking the equivlene of pirs of
GT Series 150. Cross Sectional View. Male Connector Assembly GT 150 FEMALE CONNECTOR ASSEMBLIES UNSEALED GT 150 FEMALE TERMINALS UNSEALED
GT eries 150 U UNELED U N E L E D ross ectional View Terminal Terminal able able ide Lock over Female onnector ssembly ide Lock over Male onnector ssembly onnector Position ssurance (P) Female Terminal
hm connectors Type A Male connector
Type A Male connector Contact arrangement Press-fi t technology Performance level II PCB thickness > 2.2 110 243-11010-15 154 243-11310-15 cpci Hot-Swap (P1) 154 243-11322-15 cpci Telephony Spec (P4) Contact
Introductory Information. Setup Guide. Introduction. Space Required for Installation. Overview of Setup. The Manuals Supplied with This Printer ENG
Introdutory Informtion Introdution Setup Guide ENG Red this mnul efore ttempting to operte the printer. Keep this mnul in hndy lotion for future referene. Overview of Setup These re the steps in printer
CMD Series. 4 Contact Row High Density Signal Connectors. Technical Characteristics
MD Series 4 ontact Row High Density Signal onnectors Offset-grid layout, four rows within dielectric connector body, mm center-to-center spacing in each row and row-to-row spacing. 0.6 mm nominal pin DI
FUEL SYSTEMS ROCHESTER 4 BARREL CARBURETOR 5 C
FUEL SYSTEMS 72085 ROCHESTER 4 BARREL CARBURETOR 5 C Tle of Contents Pge Rohester 4 Brrel Cruretor............. 5C-1 Torque Speifitions.................. 5C-1 Tools................................. 5C-1
McAfee Network Security Platform
XC-240 Lod Blner Appline Quik Strt Guide Revision D MAfee Network Seurity Pltform This quik strt guide explins how to quikly set up nd tivte your MAfee Network Seurity Pltform XC-240 Lod Blner. The SFP+
Tri-Start TM TV-CTV. High performance threaded cylindrical connectors TV-CTV QPL APPROVED. MIL-DTL-38999 III subminiature cylindrical connectors
ri-trt - -- suminiture lindril onnetors in fetures hell mteril - omposite - luminium - rine ronze - tinless steel inish - Olive dr dmium plting - ikel plting - ssivtion (for steel versions) shell sizes
Classic Update Series
lassic Update Series *** These are special instructions for connecting your wiring system to a stock instrument cluster. *** REFER TO THE TTHED DIGRMS FOR YOUR PPLITION YER. USE THE ENLOSED PRTS ND INFORMTION
UNIVERSITY AND WORK-STUDY EMPLOYERS WEBSITE USER S GUIDE
UNIVERSITY AND WORK-STUDY EMPLOYERS WEBSITE USER S GUIDE Tble of Contents 1 Home Pge 1 2 Pge 2 3 Your Control Pnel 3 4 Add New Job (Three-Step Form) 4-6 5 Mnging Job Postings (Mnge Job Pge) 7-8 6 Additionl
the machine and check the components Black Yellow Cyan Magenta Starter Ink Cartridges Product Registration Sheet (USA only)
Quik Setup Guide Strt Here DCP-J140W Thnk you for hoosing Brother, your support is importnt to us nd we vlue your usiness. Your Brother produt is engineered nd mnuftured to the highest stndrds to deliver
TECHNICAL DATA TYPE WSL OFF-CIRCUIT TAP CHANGER
TECHNICAL DATA TYPE WSL OFFCIRCUIT TAP CHANGER SHANGHAI HUAMING POWER EQUIPMENT CO., LTD. TYPE WSL OFFCIRCUIT TAP CHANGER TECHNICAL DATA Contents 1. Generl 2 2. Technicl specifictions 2 3. Type designtion
CHAPTER 31 CAPACITOR
. Given tht Numer of eletron HPTER PITOR Net hrge Q.6 9.6 7 The net potentil ifferene L..6 pitne v 7.6 8 F.. r 5 m. m 8.854 5.4 6.95 5 F... Let the rius of the is R re R D mm m 8.85 r r 8.85 4. 5 m.5 m
Module 5. Three-phase AC Circuits. Version 2 EE IIT, Kharagpur
Module 5 Three-hse A iruits Version EE IIT, Khrgur esson 8 Three-hse Blned Suly Version EE IIT, Khrgur In the module, ontining six lessons (-7), the study of iruits, onsisting of the liner elements resistne,
1. Definition, Basic concepts, Types 2. Addition and Subtraction of Matrices 3. Scalar Multiplication 4. Assignment and answer key 5.
. Definition, Bsi onepts, Types. Addition nd Sutrtion of Mtries. Slr Multiplition. Assignment nd nswer key. Mtrix Multiplition. Assignment nd nswer key. Determinnt x x (digonl, minors, properties) summry
Trapezoidal-Connectors Series TMC
Trapezoidal-Connectors Series TMC Subminiature-D Connectors to DIN 41 652/IEC 807-3 General Series TMC connectors are available in 5 different housing sizes with 9, 15, 25, 37 and 50 pins. In applications
Start Here. IMPORTANT: To ensure that the software is installed correctly, do not connect the USB cable until step 17. Remove tape and cardboard
Strt Here 1 IMPORTANT: To ensure tht the softwre is instlled correctly, do not connect the USB cle until step 17. Follow the steps in order. If you hve prolems during setup, see Trouleshooting in the lst
2/2-, 3/2- and 4/2-way poppet directional valves, solenoid actuated Model M-.SEW 6
R 22 58/9.99 Replces: 6.98 R 22 58/9.99 2/2-, 3/2- nd 4/2-wy poppet directionl vlves, solenoid ctuted Model M-.SEW 6 Nominl size 6 Series 3X Mximum operting pressure 61/915 SI (42/63 r) Mximum flow 6.6
VIESMANN. VITODENS AND VITOSOLAR Flue systems for gas condensing boilers 1.9 to 150.0 kw. Technical guide FLUE SYSTEMS VITODENS AND VITOSOLAR
VIESMANN VITODENS AND VITOSOLAR Flue systems f gs ondensing oilers 1.9 to 150.0 kw Tehnil guide FLUE SYSTEMS VITODENS AND VITOSOLAR 5/01 Index Index 1. Flue systems 1. 1 Flue systems... 4 Struturl unit...
Enterprise Digital Signage Create a New Sign
Enterprise Digitl Signge Crete New Sign Intended Audiene: Content dministrtors of Enterprise Digitl Signge inluding stff with remote ess to sign.pitt.edu nd the Content Mnger softwre pplition for their
Start Here. Quick Setup Guide MFC-8710DW MFC-8810DW MFC-8910DW. the machine and check the components
Quik Setup Guide Strt Here MFC-8710DW MFC-8810DW MFC-8910DW Thnk you for hoosing Brother, your support is importnt to us nd we vlue your usiness. Your Brother produt is engineered nd mnuftured to the highest
Installer reference guide
Instller referene guide Dikin Altherm hyrid het pump + EVLQ05+08CA EHYHBH05AA EHYHBH/X08AA Instller referene guide Dikin Altherm hyrid het pump English Tle of ontents Tle of ontents 1 Aout the produt 3
THE LONGITUDINAL FIELD IN THE GTEM 1750 AND THE NATURE OF THE TERMINATION.
THE LONGITUDINAL FIELD IN THE GTEM 175 AND THE NATURE OF THE TERMINATION. Benjmin Guy Loder Ntionl Physil Lbortory, Queens Rod, Teddington, Middlesex, Englnd. TW11 LW Mrtin Alexnder Ntionl Physil Lbortory,
U-BLHB-2 SIZE: C SHEET 1 OF 1
POST TOP ULLHORN RKET TLOG # ESRIPTION EP (SQ. FT.) U-LH- IN LINE FLOO MOUNT.0 7.00 7.00 IN SHE 0 PIPE (Ø.8 O X Ø.07 I) REMOVLE P 5.56 / SHE 0 PIPE (Ø.88 O X Ø.7 I).00.00 () /8-6 UN SET SREWS T. ~ THRU
OUTLINE SYSTEM-ON-CHIP DESIGN. GETTING STARTED WITH VHDL August 31, 2015 GAJSKI S Y-CHART (1983) TOP-DOWN DESIGN (1)
August 31, 2015 GETTING STARTED WITH VHDL 2 Top-down design VHDL history Min elements of VHDL Entities nd rhitetures Signls nd proesses Dt types Configurtions Simultor sis The testenh onept OUTLINE 3 GAJSKI
Ratio and Proportion
Rtio nd Proportion Rtio: The onept of rtio ours frequently nd in wide vriety of wys For exmple: A newspper reports tht the rtio of Repulins to Demorts on ertin Congressionl ommittee is 3 to The student/fulty
8060 Series Alternate Action and Momentary Pushbutton Switches
Features/Benefits Long travel vailable with LED Long life contact design Epoxy terminal seal compatabile with bottom wash cleaning RoHS compliant models available Typical pplications Instrumentation Computers
End-to-end development solutions
TECHNICAL SERVICES Endtoend development solutions Mnged y TFE HOTELS TFE Hotels re the only Austrlin Hotel group with inhouse end to end development solutions. We hve expertise in Arhiteturl nd Interior
the machine and check the components Starter Ink Cartridges Basic User s Guide Product Safety Guide Telephone Line Cord
Quik Setup Guide Strt Here MFC-J450DW MFC-J470DW Thnk you for hoosing Brother, your support is importnt to us nd we vlue your usiness. Your Brother produt is engineered nd mnuftured to the highest stndrds
Quick Guide to Lisp Implementation
isp Implementtion Hndout Pge 1 o 10 Quik Guide to isp Implementtion Representtion o si dt strutures isp dt strutures re lled S-epressions. The representtion o n S-epression n e roken into two piees, the
Size 20 Contacts Solder and Crimp Removable. Military Quality and Severe Industrial Environmental Applications. Environmental-D Series
Environmental-D MILITRY QULITY, REMOVLE CONTCT, SUMINITURE-D CONNECTORS FOR MILITRY ND SEVERE INDUSTRIL ENVIRONMENTL PPLICTIONS Size 20 Contacts Solder and Crimp Removable Military Quality and Severe Industrial
SE3BB4: Software Design III Concurrent System Design. Sample Solutions to Assignment 1
SE3BB4: Softwre Design III Conurrent System Design Winter 2011 Smple Solutions to Assignment 1 Eh question is worth 10pts. Totl of this ssignment is 70pts. Eh ssignment is worth 9%. If you think your solution
Evolant Solutions Distribution System Series 71
Evolnt Solutions Distriution System Series 71 Contents Introduction One of the leding Suppliers of MDF Products 04 An Excellent Qulity Mngement System 05 Technicl Principles Insultion Displcement Connection
Connectors. product overview. Edition 3
Connectors product overview Edition 3 Editorial Good connections bear a name: ept Thomas Bernhard Claus Guglhör Guglhör Guglhör ept designs, produces and distributes electronic connectors for highquality
Practice Test 2. a. 12 kn b. 17 kn c. 13 kn d. 5.0 kn e. 49 kn
Prtie Test 2 1. A highwy urve hs rdius of 0.14 km nd is unnked. A r weighing 12 kn goes round the urve t speed of 24 m/s without slipping. Wht is the mgnitude of the horizontl fore of the rod on the r?
Angles 2.1. Exercise 2.1... Find the size of the lettered angles. Give reasons for your answers. a) b) c) Example
2.1 Angles Reognise lternte n orresponing ngles Key wors prllel lternte orresponing vertilly opposite Rememer, prllel lines re stright lines whih never meet or ross. The rrows show tht the lines re prllel
StyleView SV32 Change Power System Batteries
F the ltest User Instlltion Guie n StyleLink Softwre Downlo plese visit: Enontrrá l versión más reiente el mnul e instlión el usurio y el softwre e StyleLink en: Si vous souhitez téléhrger le ernier mnuel
How To Balance Power In A Distribution System
NTERNATONA JOURNA OF ENERG, ssue 3, ol., 7 A dynmilly S bsed ompt ontrol lgorithm for lod blning in distribution systems A. Kzemi, A. Mordi Koohi nd R. Rezeipour Abstrt An lgorithm for pplying fixed pitor-thyristorontrolled
Directory chapter 04
M Directory chapter 04 D-Sub Mixed subminiature D connectors New Page D-Sub mixed connector system general information................... 04.02 Contact arrangements............................................
Start Here. Quick Setup Guide. the machine and check the components DCP-9020CDW
Quik Setup Guide Strt Here DCP-9020CDW Plese red the Produt Sfety Guide first, then red this Quik Setup Guide for the orret setup nd instlltion proedure. To view the Quik Setup Guide in other lnguges,
Experiment 6: Friction
Experiment 6: Friction In previous lbs we studied Newton s lws in n idel setting, tht is, one where friction nd ir resistnce were ignored. However, from our everydy experience with motion, we know tht
Reasoning to Solve Equations and Inequalities
Lesson4 Resoning to Solve Equtions nd Inequlities In erlier work in this unit, you modeled situtions with severl vriles nd equtions. For exmple, suppose you were given usiness plns for concert showing
How To Organize A Meeting On Gotomeeting
NOTES ON ORGANIZING AND SCHEDULING MEETINGS Individul GoToMeeting orgnizers my hold meetings for up to 15 ttendees. GoToMeeting Corporte orgnizers my hold meetings for up to 25 ttendees. GoToMeeting orgnizers
Before you can use the machine, please read this Quick Setup Guide for the correct setup and installation.
Quik Setup Guide Strt Here DCP-365CN DCP-373CW DCP-375CW DCP-377CW Before you n use the mhine, plese red this Quik Setup Guide for the orret setup nd instlltion. WARNING CAUTION Wrnings tell you wht to
ETH Electro Cylinder. Parker High Force Electro Thrust Cylinder
ETH Eletro Cylinder Prker High Fore Eletro Thrust Cylinder WARNING USER RESPONSIBILITY FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL
GENERAL OPERATING PRINCIPLES
KEYSECUREPC USER MANUAL N.B.: PRIOR TO READING THIS MANUAL, YOU ARE ADVISED TO READ THE FOLLOWING MANUAL: GENERAL OPERATING PRINCIPLES Der Customer, KeySeurePC is n innovtive prout tht uses ptente tehnology:
Excellent The soldering tip from Weller innovative and reduces costs
Exellent The soldering tip from Weller innovtive nd redues osts 1 Tool protetion. Perfet intertion etween the heting element nd the soldering tip. Weller soldering tips re designed t the Weller Germn Reserh
p-q Theory Power Components Calculations
ISIE 23 - IEEE Interntionl Symposium on Industril Eletronis Rio de Jneiro, Brsil, 9-11 Junho de 23, ISBN: -783-7912-8 p-q Theory Power Components Clultions João L. Afonso, Memer, IEEE, M. J. Sepúlved Freits,
Simulation of a large electric distribution system having intensive harmonics in the industrial zone of Konya
Turkish Journl of Eletril Engineering & omputer Sienes http:// journls. tuitk. gov. tr/ elektrik/ Reserh rtile Turk J Ele Eng & omp Si (2013) 21: 934 944 TÜİTK doi:10.3906/elk-1201-55 Simultion of lrge
c b 5.00 10 5 N/m 2 (0.120 m 3 0.200 m 3 ), = 4.00 10 4 J. W total = W a b + W b c 2.00
Chter 19, exmle rolems: (19.06) A gs undergoes two roesses. First: onstnt volume @ 0.200 m 3, isohori. Pressure inreses from 2.00 10 5 P to 5.00 10 5 P. Seond: Constnt ressure @ 5.00 10 5 P, isori. olume
Start Here. Quick Setup Guide. the machine and check the components. NOTE Not all models are available in all countries.
Quik Setup Guide Strt Here HL-3140CW / HL-3150CDN HL-3150CDW / HL-3170CDW Thnk you for hoosing Brother, your support is importnt to us nd we vlue your usiness. Your Brother produt is engineered nd mnuftured
SECTION 7-2 Law of Cosines
516 7 Additionl Topis in Trigonometry h d sin s () tn h h d 50. Surveying. The lyout in the figure t right is used to determine n inessile height h when seline d in plne perpendiulr to h n e estlished
JaERM Software-as-a-Solution Package
JERM Softwre-s--Solution Pckge Enterprise Risk Mngement ( ERM ) Public listed compnies nd orgnistions providing finncil services re required by Monetry Authority of Singpore ( MAS ) nd/or Singpore Stock
FUEL SYSTEMS MERCARB 2 BARREL CARBURETOR 5 B
FUEL SYSTEMS 72681 MERCARB 2 BARREL CARBURETOR 5 B Tle of Contents Pge MerCr 2 BBL Cruretor.............. 5B-1 Torque Specifictions................ 5B-1 Tools............................... 5B-1 Specifictions.......................
the machine and check the components
Quik Setup Guide Strt Here MFC-7360N MFC-7460DN Plese red the Sfety nd Legl ooklet first efore you set up your mhine. Then, plese red this Quik Setup Guide for the orret setup nd instlltion. To view the
APPLICATION NOTE Revision 3.0 MTD/PS-0534 August 13, 2008 KODAK IMAGE SENDORS COLOR CORRECTION FOR IMAGE SENSORS
APPLICATION NOTE Revision 3.0 MTD/PS-0534 August 13, 2008 KODAK IMAGE SENDORS COLOR CORRECTION FOR IMAGE SENSORS TABLE OF FIGURES Figure 1: Spectrl Response of CMOS Imge Sensor...3 Figure 2: Byer CFA Ptterns...4
VMware Horizon FLEX Administration Guide
VMwre Horizon FLEX Administrtion Guide Horizon FLEX 1.0 This doument supports the version of eh produt listed nd supports ll susequent versions until the doument is repled y new edition. To hek for more
OxCORT v4 Quick Guide Revision Class Reports
OxCORT v4 Quik Guie Revision Clss Reports This quik guie is suitble for the following roles: Tutor This quik guie reltes to the following menu options: Crete Revision Clss Reports pg 1 Crete Revision Clss
Data Quality Certification Program Administrator In-Person Session Homework Workbook 2015-2016
Dt Qulity Certifition Progrm Aministrtor In-Person Session Homework Workook 2015-2016 Plese Note: Version 1.00: Pulishe 9-1-2015 Any exerises tht my e upte fter this printing n e foun online in the DQC
8146 Series Terminal Boxes
Series Terminal oxes TERMINTION Ready-Term Terminal oxes Features: Pre-onfigured with terminals mounted Made of Fiberglass Reinforced Polyester (FRP) enclosure sizes with different depths For power and
BUSINESS PROCESS MODEL TRANSFORMATION ISSUES The top 7 adversaries encountered at defining model transformations
USINESS PROCESS MODEL TRANSFORMATION ISSUES The top 7 dversries enountered t defining model trnsformtions Mrion Murzek Women s Postgrdute College for Internet Tehnologies (WIT), Institute of Softwre Tehnology
2. VOLTAGE TRANSFORMERS Support type Support type with fuse Touch-proof type
2. VOLTGE TRSFORMERS Support type Support type with fuse Touch-proof type 16 Instrument trnsformers Medium voltge indoor 2. VOLTGE TRSFORMERS ITRODUCTIO Voltge trnsformers reduce the voltge in the medium
NEMA Push Button Specifications
Tehnil Dt NEM Push utton Speifitions tlog Numers 800T nd 800 Topi Pge 800T/ Speifitions 2 800T/ DevieNet Sttions 4 800T/ Trigger tion E-stops 5 800T/ Momentry ontt Push uttons 7 800T/ Seletor Swith 10
EP Series Sealed Tiny Pushbutton Switches Typical Applications
Features/Benefits Sealed against solder & cleaning processes Thru-hole and surface mount models Snap-fitting actuator accepts standard caps Tape & reel packaging available RoHS compliant models available
ORGANIZER QUICK REFERENCE GUIDE
NOTES ON ORGANIZING AND SCHEDULING MEETINGS Individul GoToMeeting orgnizers my hold meetings for up to 15 ttendees. GoToMeeting Corporte orgnizers my hold meetings for up to 25 ttendees. GoToMeeting orgnizers
Solatube Brighten Up Series
Soltue Brighten Up Series Soltue 60 DS Dylighting System Soltue 290 DS Dylighting System Instlltion Instrutions 8 Prts List * Quntity Dome with Ryender 3000 Tehnology (). Shok Inner Dome* 8 2 Roof Flshing
Assembly tools. ept GmbH & Co. KG I Phone +49 (0) 88 61 / 25 01 0 I Fax +49 (0) 88 61 / 55 07 I E-mail sales@ept.de I www.ept.
192 ssembly tools TC products 194 Hardmetric products 198 ccessories 204 DIN products 206 ccessories 212 PC/104, PC/104-Plus 214 VarPol connectors 214 Power terminals 216 Other tools 218 ept GmbH & Co.
M.7 CONTENTS. Measurement transformers and shunts. Introduction Page 3 TC 5 TC 5,2 TC 6,2 TC 6 TC 8 TC 10 TC 12. Slim line current transformers Page 7
Current transformers and shunts M7 M.7.01 GB CONTENTS Introdution Page 3 TC TCH T TC 5 TC 5,2 TC 6,2 TC 6 TC 8 TC 10 TC 12 TCH 6,2 TCH 6 TCH 8 TCH 10 TCH 12 T 400 T 0 T 600 Slim line urrent transformers
RJ45 Connectors. RJ45 Connectors. Interconnect Solutions Worldwide
Connectors Connectors D3999 Derived Cat5e / Cat6 & Cat6a Connector ssemblies for Harsh Environments NCGE Code U5792 www.polamco.com Connectors D3999 Derived Cat5e / Cat6 & Cat6a Connector ssemblies for
Lesson 2.1 Inductive Reasoning
Lesson.1 Inutive Resoning Nme Perio Dte For Eerises 1 7, use inutive resoning to fin the net two terms in eh sequene. 1. 4, 8, 1, 16,,. 400, 00, 100, 0,,,. 1 8, 7, 1, 4,, 4.,,, 1, 1, 0,,. 60, 180, 10,
HSD High Speed Data interconnection
HSD High Speed Data interconnection Fast, safe and robust Very high data bit rate up to 5 Gbit/s SSR smart strain relief enables unstressed solder joints Excellent resistance against cross-talk and RF-EMC
Cree XLamp XP-E High-Efficiency White LEDs
Product family data sheet ree XLamp XP-E High-Efficiency White LEDs LD-DS34 Rev 0 www. cree.com/xlamp PRODUT DESRIPTION XLamp XP-E High-Efficiency White LEDs upgrade the XLamp XP-E to leading performance
CI/SfB. Legge (31.59) X. May 2001. Lever locks, mortice latches & nightlatches
Unilss L4 EPIC D6 Legge Lever loks, mortie lthes & nightlthes CI/SfB My 01 (31.5) X The World s No. 1 For more thn entury, the nme IR hs een synonymous with the very est in design, mnufture nd instlltion
15.6. The mean value and the root-mean-square value of a function. Introduction. Prerequisites. Learning Outcomes. Learning Style
The men vlue nd the root-men-squre vlue of function 5.6 Introduction Currents nd voltges often vry with time nd engineers my wish to know the verge vlue of such current or voltge over some prticulr time
Maximum drive current: 3000 ma. Low thermal resistance: 2.5 C/W. Maximum junction temperature: 150 C. Viewing angle: 125
ree XLamp XM-L LEDs PRODUT FMILY DT SHEET LD-DS33 REV 2 WWW.REE.OM/XLMP PRODUT DESRIPTION The XLamp XM-L LED is the industry s highest performance, singledie white lighting-class LED. XLamp XM-L is 20%
Welch Allyn CardioPerfect Workstation Installation Guide
Welch Allyn CrdioPerfect Worksttion Instlltion Guide INSTALLING CARDIOPERFECT WORKSTATION SOFTWARE & ACCESSORIES ON A SINGLE PC For softwre version 1.6.5 or lter For network instlltion, plese refer to
CS 316: Gates and Logic
CS 36: Gtes nd Logi Kvit Bl Fll 27 Computer Siene Cornell University Announements Clss newsgroup reted Posted on we-pge Use it for prtner finding First ssignment is to find prtners P nd N Trnsistors PNP