8060 Series Alternate Action and Momentary Pushbutton Switches

Transcription

1 Features/Benefits Long travel vailable with LED Long life contact design Epoxy terminal seal compatabile with bottom wash cleaning RoHS compliant models available Typical pplications Instrumentation Computers and peripherals Telecommunications and networking equipment Models vailable Specifications CONTCT RTING: Q contact material: V C or 28 V DC; V C. See page -59 for additional ratings. ELECTRICL LIFE: 50,000 make-and-break cycles at full load. CONTCT RESISTNCE: Below 20 mω typ. 2-4 V DC, 100 m, for both silver and gold plated contacts. INSULTION RESISTNCE: 10 9 Ω min. DIELECTRIC STRENGTH: 1,000 Vrms sea level. OPERTING TEMPERTURE: 30ºC to 65ºC SOLDERBILITY: Per MIL-STD-202F method 208D, or EI RS-186E method 9 (1 hour steam aging). CP INSTLLTION FORCE: 10 lbs. maximum permissible. NOTE: ny models supplied with P, R, S, Q, B or G contact material are RoHS compliant. NOTE: Specifications and materials listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center. Materials CSE: Glass filled nylon 6/6 or diallyl phthalate (DP), flame retardant (UL 94V-0). PLUNGER: S, S1, S2 Options: Glass filled nylon or glass filled polyester (PBT) (UL 94V-0). L, L1 Options: Brass, nickel plated. CP & FRME: Nylon, black standard. BUSHING: Brass or zinc, nickel plated. HOUSING: Stainless steel. SWITCH SUPPORT: Brass or steel, matte-tin plated. END CONTCTS: Q contact material: Coin silver, silver plated. See page -59 for additional contact materials. CENTER CONTCT & LL TERMINLS: Q contact material: Copper alloy, silver plated. See page -59 for additional contact materials. TERMINL SEL: Epoxy. Refer to soldering and cleaning in Technical Data Chapter. HRDWRE: Nut & Locking Ring: Brass, nickel plated; Lockwasher: Steel, nickel plated. Build--Switch To order, simply select desired option from each category and place in the appropriate box. vailable options are shown and described on pages -53 thru -61. For additional options not shown in catalog, consult Customer Service Center. ll models have epoxy terminal seal and are compatible with all bottom-wash PCB cleaning methods. Switch Function 8161 On-On 8168 On-Mom On-On ctuator or Plunger S.710" high plunger with.375" dia. cap J80 Snap-in J81 Snap-in with frame J82 Snap-in with frame for LED J86 Snap-in with frame & LED L.740" high plunger with.395" dia. cap L1.740" high plunger with.590" dia. cap S1.615" high plunger with.200" dia. cap S2.710" high plunger with.310" dia. cap Bushing H.300" high, flat, hi torque H9.300" high, flat, hi torque NONE No bushing choice required Y3 7.6mm, keyway Terminations Right angle, PC thru-hole V2 Vertical right angle, PC thru-hole C PC Thru-hole Z Solder lug 3 Right angle, snap-in, PC thru-hole V3 Vertical right angle, snap-in, PC thru-hole V3.460" high, V-bracket V4.630" high, V-bracket V6.460" high, V-bracket V21.555" high, snap-in V-bracket V31.460" high, snap-in V-bracket W.750" long, wire wrap Z3 Quick connect Contact Material B Gold P Gold, matte-tin Q Silver S Silver, matte-tin G Gold over silver R Gold over silver, matte-tin Seal E Epoxy I Epoxy potted base Cap Color 2 Black 1 White 3 Red 4 Orange 5 Yellow 9 Gray Frame Color 2 Black LED Color 3 Red NONE Models without LED -52

2 SWITCH FUNCTION NO. POLES SP MODEL NO SWITCH FUNCTION POS. 1 POS. 2 C&K marking this side ON ON ON MOM. CONNECTED TERMINLS POS. 1 POS. 2 C&K marking this side SCHEMTIC Part number shown: 8161SHZQE Terminal Nos. For Reference Only DP 8261 ON ON 2-3, ,5-4 Part number shown: 8261SHZQE MOM. = Momentary ll models Terminal Nos. For Reference Only with all options when ordered with G or Q contact material. CTUTOR SNP-IN FRONT MOUNT CTUTOR OR PLUNGER CP COLOR J80 SNP-IN PNEL MOUNTING CP COLOR * 2 BLCK 1 WHITE 3 RED 4 ORNGE 5 YELLOW 9 GRY Cap Finish: matte. Other colors available, consult Customer Service Center. vailable with C, W, Z or Z3 terminations. NOTE: Caps & frames available separately, see pages -60 and -61. J81 SNP-IN WITH BLCK FRME *Increase this dimension to.620/.625 (15,75/15,88) for.091/.125 (2,41/2,18) thick panels. PNEL MOUNTING * *Increase this dimension to.620/.625 (15,75/15,88) for.091/.125 (2,41/2,18) thick panels. -53

3 8060 Series J82 CTUTOR SNP-IN FRONT MOUNT SNP-IN WITH BLCK FRME FOR LED CTUTOR OR PLUNGER CP COLOR vailable with C, W, Z or Z3 terminations. LED not included. For LED information, see page -61. NOTE: Caps & frames available separately, see pages -60 and -61. Other colors available, consult Customer Service Center. CP COLOR 2 BLCK 1 WHITE 3 RED 4 ORNGE 5 YELLOW 9 GRY J86 CTUTOR SNP-IN FRONT MOUNT SNP-IN WITH BLCK FRME ND LED CTUTOR OR PLUNGER CP COLOR LED COLOR PNEL MOUNTING * 8161J86ZQE223 * Increase this dimension to.620/.625 (15,75/15,88) for.091/.125 (2,31/3,18) thick panels. vailable with C, W, Z or Z3 terminations and models only. NOTE: Caps & frames available separately, see pages -60 and -61. Other colors available, consult Customer Service Center. CP COLOR 2 BLCK 1 WHITE 3 RED 4 ORNGE 5 YELLOW 9 GRY 3 RED LED COLOR For LED information, see page

4 S PLUNGER WITH CP P/N 7527 PLUNGER CP COLOR CTUTOR OR PLUNGER S1 PLUNGER WITH CP P/N 7089 S2 PLUNGER WITH CP P/N 8018 L PLUNGER WITH CP P/N 8941 L1 PLUNGER WITH CP P/N 8940 CP COLOR 2 BLCK 1 WHITE 3 RED 4 ORNGE 5 YELLOW 9 GRY Cap Finish: gloss. Cap supplied not installed. Other colors available, consult Customer Service Center. NOTE: When selecting plunger and cap option, bushing selection must also be made, see below. BUSHING H.300" HIGH THREDED, FLT H9.300" HIGH UNTHREDED, FLT NONE NO BUSHING CHOICE REQUIRED (JXX CTUTORS) Y3 7.6mm THREDED, KEYWY 1/4±40 UNS-2 H bushing standard with C, W, Z or Z3 terminations. H9 bushing standard with, 3, V2, V3, or V3-V31 terminations. Withstands 12 in./lbs. of torque with no distortion. Withstands 12 in./lbs. of torque with no distortion. NOTE: When selecting bushing option, plunger selection must also be made, see above. No bushing option choice required when any JXX actuator option is selected. NOTE. Two mounting nuts, locking ring and lockwasher supplied standard with threaded bushings. Optional mounting nut and locking ring styles and finishes available, see section Technical Data and dditional Hardware. -55

5 C PC THRU-HOLE TERMINTIONS Z SOLDER LUG and and Not available with P, S or R contact material. Z3 QUICK CONNECT W WIRE WRP.750 (19,05) and HOLE RIGHT NGLE, PC THRU- Not available with P, S or R contact material. Mating quick connector available; order part number , page -61. and.130 (3,3).138 (3,51) 8161SH9BE2 SECTION - 3 RIGHT NGLE, SNP-IN, PC THRU-HOLE Terminal bend radii and lead-in manufacturing option. NOTE: PC pattern must clear switch support leg. -56

6 RIGHT NGLE, PC THRU-HOLE TERMINTIONS SECTION SH9BE2 3 RIGHT NGLE, SNP-IN, PC THRU-HOLE Terminal bend radii and lead-in manufacturing option. V2 VERTICL RIGHT NGLE, PC THRU-HOLE,.150" PITCH 8161SH9V2BE2 V3 VERTICL RIGHT NGLE, SNP-IN, PC THRU-HOLE,.150" PITCH Terminal bend radii and lead-in manufacturing option. -57

7 8060 Series V2 TERMINTIONS VERTICL RIGHT NGLE, PC THRU-HOLE,.150" PITCH 8261SH9V2BE2 SECTION - V3 VERTICL RIGHT NGLE, SNP-IN, PC THRU-HOLE,.150" PITCH Terminal bend radii and lead-in manufacturing option. V6 V21 VERTICL MOUNT, V-BRCKET VERTICL MOUNT, V-BRCKET, SNP-IN 8161SH9 BE2 DIM V (14,10) V6.460 (11,68) V6 V21 VERTICL MOUNT, V-BRCKET VERTICL MOUNT, V-BRCKET, SNP-IN DIM 8261SH9 BE2 V (14,10) V6.460 (11,68) -58

8 TERMINTIONS V3, V4 VERTICL MOUNT, V-BRCKET V31 VERTICL MOUNT, V-BRCKET, SNP-IN 8161SH9 BE2 DIM V3, V (11,68) V4.630 (16,00) V3, V4 VERTICL MOUNT, V-BRCKET V31 VERTICL MOUNT, V-BRCKET, SNP-IN 8261SH9 BE2 SNP-IN DIM V3, V (11,68) V4.630 (16,00) CONTCT MTERIL CONTCT MTERIL TERMINL PLTING RTINGS B P GOLD 1 GOLD 1 MTTE-TIN 6 LOW LEVEL/DRY CIRCUIT 0.4 V 20 V C OR DC MX. Q S SILVER 4,5 SILVER 5 MTTE-TIN 6 POWER V C OR 28 V DC; V C. G R GOLD OVER SILVER 2,3 GOLD 3 MTTE-TIN 6 LOW LEVEL/DRY CIRCUIT OR POWER 0.4 V 20 V C OR DC MX. OR V C OR 28 V DC; V C. * Note: See Technical Data section of this catalog for RoHS compliant and compatible definitions and specifications. 1 CONTCTS & TERMINLS: Copper alloy, with gold plate over nickel plate. END CONTCTS: Coin silver, with gold plate over nickel plate. ll models contact material. with all options when ordered with S, R, G, or Q 3 CENTER CONTCTS & LL TERMINLS: Copper alloy, with gold plate over nickel plate. END CONTCTS: Coin silver, silver plated. B contact material standard with all terminations except C, Z & Z3. Q contact material standard with C, Z & Z3 terminations. P, S & R contact materials not available with Z & Z3 terminations. 5 CENTER CONTCT & LL TERMINLS: Copper alloy, silver plated. 6 TERMINLS: Copper alloy, with matte-tin over nickel plate. NOTE: ny models supplied with P, S, R,Q, B or G contact material are RoHS compliant. -59

9 8060 Series E EPOXY SEL SEL I EPOXY POTTED BSE NOTE: vailable with C, W, Z, Z3 terminations only. VILBLE HRDWRE Cap.120 (3,05).200 DI. (5,08 ) Cap Cap.155 (3,94) WHITE BLCK RED ORNGE YELLOW GRY Cap, Snap-fitting plunger WHITE BLCK RED ORNGE YELLOW GRY Cap, Snap-fitting plunger WHITE BLCK RED ORNGE YELLOW GRY Cap, J80, J81 & J82 options only 452D D D D D D09000 WHITE BLCK RED ORNGE YELLOW GRY WHITE BLCK RED ORNGE YELLOW GRY WHITE BLCK RED ORNGE YELLOW GRY WHITE BLCK RED ORNGE YELLOW GRY Finish: Matte Cap, J86 & J96 options only Frame Frame WHITE BLCK RED ORNGE YELLOW GRY BLCK Finish: Matte BLCK Finish: Matte Finish: Matte NOTE: dditional nuts, locking rings and lockwashers available separately, see section Technical Data and dditional Hardware. Other cap & frame colors available, consult Customer Service Center. -60

10 Fits Z3 Termination female connector vailable in loose pieces. VILBLE HRDWRE Frames snap into panel opening and are independent from switch mounting. ccurate positioning of the PC mounted switch relative to the panel opening is necessary to provide proper clearance between actuator and frame. vailable in two basic styles and four panel thicknesses in.. Finish: Matte. TYPICL PPLICTION.047" (1,19) PNEL THK..062" (1,57) PNEL THK..090" (2,29) PNEL THK..125" (3,18) PNEL THK BLCK Panel Inserts bove frames (part nos. 432XXXXXX) are also available with insert which accepts LED for indicator light assembly. Order insert separately from frame. Blank insert panel (without hole for LED) also available. LED not included. PNEL INSERT WITH HOLE FOR LED BLNK PNEL INSERT WITHOUT HOLE FOR LED BLCK Special colors, custom markings available, consult Customer Service Center. LED INFORMTION SWITCHES WITH LED SUPPLIED: J86 : Rectangular LEDs are supplied on 8060 Series pushbutton switches with J86 option. These LEDs are factory installed and are not replaceable. The following specifications apply: COLOR TYP. INTENSITY TYP. FORWRD VOLTGE TYP. FORWRD CURRENT MX RTINGS T 25ºC MBIENT TEMPERTURE FORWRD CONTINUOUS POWER VOLTGE FORWRD CURRENT DISSIPTION Flat denotes cathode..20 DI. (5,08 ).025 SQ. TYP. (0,63) Green Red* Yellow 1.0 mcd 0.5 mcd 4.0 mcd 2.1 V 20 m 10 m 20 m mw 75 mw 125 mw.230 DI. (5,84 ) Process Information: Soldering to LED leads must be completed within 5 seconds at 500ºF (260ºC) maximum. Caution: Circuit elements must limit forward current of LED to 50m max. continuous. * Extra-bright red LED available (typ. intensity 4.5 mcd), consult Customer Service Center. LEDs are not supplied with J82 & J84 options. LED snaps into switch frame surrounding actuator and is wired externally. 2.5 V 50 m 30 m 50 m.030 (0,76).340 (8,64) Suggested LED for J82 & J84 options. Dimensions for reference only..750 (19,05)