MIL-DTL type receptacle connector with size 8 opto-electronic contacts

Transcription

1 Series III Type ctive Receptacle onnector with Glenair Size 8 Opto-electronic s Opto-lectronic MIL-TL type receptacle connector with size 8 opto-electronic contacts TURS series of ctive Opto-electronic sealed panel mount connectors offers customers the power to convert from electrical to fiber optic signals within a connector to support high speed fiber optic transmission in harsh environments. The s incorporates size 8 active contacts in one of three standard configurations to enable optical s, optical s or Optical Transceivers. The optoelectronic performance parameters of the are defined by the performance of the size 8 contacts that are incorporated. or example if one incorporates 4.25Gbps contacts into the connector then each of the contacts will be 4.25Gbps capable. The fiber optic signal that is generated within the active connectors is transmitted via RIN 801 fiber optic connector interface to fiber optic cable system using a standard plug connector that has been fitted with adapters to incorporate RIN 801 fiber optic contacts. or example a plug connectors with size #8 contact cavities, such as insert arrangement (per MIL-ST-1560) can be fitted with Glenair RIN 801 contact adaptersthat convert this electrical connector into a fiber optic connector that enables it to properly house and retain contacts at the required optical interface to achieve very repeatable low loss optical transmission characteristics OMPNION SSORY PTR PROUTS These adapters are used to make the PLUG connector that serves as the fiber optic cable interface adapters convert size 8 cavities (twinax, coax, quadrax or power cavities) into RIN 801 Luxis fiber optic connectors. PPLITIONS Supports up to 34Gbps aggregate transmission bandwidth in a single connector MIL-ST-1560 arrangements & Glenair arrangements rrangements from 1 to 8 size 8 cavities available, contact factory for custom arrangements Operating temperatures -40 to +85 as supported by the size 8 contacts May be configured in one of 3 standard configurations:, or Transceiver contacts to support RIN mm fiber optic interconnect, 100Mbps to 4.25Gbps per contact dapters available to support converting PLUG size 8 cavities into RIN 801 fiber optic compatible connectors adapters convert size 8 cavities (twinax, coax, quadrax or power cavities) into RIN 801 appendix, N4531, LIO Support Harsh nvironment applications where robust connectors are required, irborne, Tactical and Shipboard thernet, ast thernet, Gigabit thernet, X, 1x/2x/4x iber hannel, VI, HMI, SP, Serial Rapid I/O (srio) and other high speed communication all over Multimode iber ctive size 8 contacts to support 2.5mm iber Optic contact systems, 100Mbps to 4.25Gbps per contact ctive size 8 contacts to support RIN mm fiber optic contact system, 10Mbps to 200Mbps, 1300nm L dapter available to support converting PLUG size 8 cavities into LIO fiber optic compatible connectors P tail electrical interfaces or custom micro-coax or flex to P interfaces available onnector rear face contains standoffs to allow direct mechanical attachment to P Glenair, Inc. Rev U.S. G ode Printed in U.S.. GLNIR, IN IR WY GLNL, X

2 Opto-lectronic Series III Type ctive Receptacle onnector with Glenair Size 8 Opto-electronic s How To Order /Insert rrangement J (MIL-ST-1560) H (Glenair pattern) G (MIL-ST-1560) (Glenair pattern) (Glenair pattern) 1-11L-01 (Glenair pattern) Product Series inish (Table I) Type (See Table II) P Standoff Option 01 - Standard N - 07 J8 T N Series III ctive Receptacle Shell Mounting Options S - Wall Mount, linch Nut Standard (38999/20 Modified) 00 - Wall Mount, Slotted (38999/20) 07 - Jam Nut Mount Opto-lectronic unction (See Table IX) T = R = X = Transceiver Polarization,,,, N = Normal Notes This connector is designed to meet applicable dimensional, environmental and performance characteristics of Series III per appropriate material class or opto-electric performance specifications, see Table II This connector mates with standard MIL-TL-38999/26 plug connector. See Table X for applicable part numbers or cleaning tools and instructions, see GLT-H125 in Glenair iber Optic catalog Receptacle contact removal tool: M81969/14-12 Plug contact insertion/removal tool: M81969/ Glenair, Inc. Rev U.S. G ode Printed in U.S.. GLNIR, IN IR WY GLNL, X

3 Series III Type ctive Receptacle onnector with Glenair Size 8 Opto-electronic s Opto-lectronic Table I: Material nd inish SYM Material inish escription M lectroless Nickel MT Nickel - PT N luminum admium, Olive rab ZR Zinc Ni, lack (Tri-Valent R) M lectroless Nickel Plate, Matte Z1 Passivate Stainless Steel ZL lectro-eposited Nickel Type (Multimode 50/125 & 62.5/125) Option Table II: Type P/N escription T 1.25 GPS R 1.25 GPS T 2.50 GPS R 2.50 GPS T 3.20 GPS R 3.20 GPS T 4.25 GPS R 4.25 GPS Type escription series optoelectronic size 8 contact, 100 MPS 4.25 GPS, 850 μm vcsel transmitter or Pin/TI receiver, 1.25mm Luxis optical interface that mates with RIN 801 terminus. Table XII: imensions ode M basic Ø GG Max (14.0).760 (19.3) (23.4) (28.7) (26.0) (31.4) G (26.0) (31.4) H (32.4) (37.7) J (36.8) (42.2) #4-40 THR.250 MIN PTH M ø GG M Table IX: Reccommended P Hole Sizes Ø J Ø L Solder Mill-Max* *Minimum P thickness to use Mill-Max contacts is.090" 5X X P Standoff Locations pplicable to ll onfigurations Ø J 2X Ø L 2X Size 8 ctive P Tail rrangement J8 rrangement xample Recommended P utout ll diameters are ll diameters are etail Scale 3: Glenair, Inc. Rev U.S. G ode Printed in U.S.. GLNIR, IN IR WY GLNL, X

4 Opto-lectronic Series III Type ctive Receptacle onnector with Glenair Size 8 Opto-electronic s Insert arrangements and P tails rrangement 1 rrangement 2 rrangement 4 P rrangement G4 rr. 11L-01 1X #8 Glenair Special Recommended P Layout Position I rr X #8 Glenair Special Recommended P Layout Position I K rr X #8 Glenair Special Recommended P Layout Position I K P rr X #8 Per M1560 Recommended P Layout Position I rrangement H6 rr X #8 Glenair Special Recommended P Layout Position I rrangement J8 G H rr X #8 Per M1560 Recommended P Layout Position I G H S R P rrangement Z N T M U L a b d c q r s e p n Y w v m k u t h K J g f V X H W G rr actory for etails 2013 Glenair, Inc. Rev U.S. G ode Printed in U.S.. GLNIR, IN IR WY GLNL, X

5 Series III Type ctive Receptacle onnector with Glenair Size 8 Opto-electronic s Opto-lectronic unction assignments and mating connectors Insert rrrangement Position I Table IX: unction ssignments T = R = X* = Transceiver 1 N/ 2 4 G4 H6 J8 K P * factory for other function assignments G H Receptacle onnector Ins. rr. Mating onnector escription Table X: Mating onnector P/N Glenair P/N** dapter Type *** 1 Glenair Special ?G6-11Q-01N Glenair Special ?G6-17Q-75N Glenair Special ?G6-19Q-04N G /26G4SN ?G6-21Q-75N H6 Glenair Special ?G6-23Q-06N J /26J8SN ?G6-25Q-08N ** Replace? with material/finish code from Table I. If unavailable, inquire about as alternative. ***Must order indicated amount for complete plug connector. adapters include respective contacts for each type Qty P/N 2013 Glenair, Inc. Rev U.S. G ode Printed in U.S.. GLNIR, IN IR WY GLNL, X

6 Opto-lectronic S Wall Mount, linch Nut Series III Type ctive Receptacle onnector with Glenair Size 8 Opto-electronic s ctive MIL-TL type wall-mount clinch nut receptacle X THR R OLOR N MX KK SQ THR S - Wall Mount, linch Nut (38999/20 Modified) (.175).613±.010 ode Table XII: imensions for linch Nut Receptacles Thread Per M38999/20 X Thread KK sq ± P-.3L-TS-2 # (30.5) P-.3L-TS-2 # (36.8) P-.3L-TS-2 # (39.4) G P-.3L-TS-2 # (41.9) H P-.3L-TS-2 # (45.0) J P-.3L-TS-2 # (48.3) Ø (RONT MOUNT) (RONT MOUNT) ø ROMMN PNL UT-OUT OR RONT PNL MOUNTING S N 00 WLL MOUNT RPTLS (NOT TO SL) ode Table XI: Recommended Panel ut-out Ø ±.005 Ø min (3.3) (20.2) (3.3) (31.0) (3.3) (32.9) G (3.3) (36.1) H (3.9) (39.3) J (3.8) (42.5) Ø (RR MOUNT) (RR MOUNT) ø ROMMN PNL UT-OUT OR K PNL MOUNTING S N 00 WLL MOUNT RPTLS (NOT TO SL) 2013 Glenair, Inc. Rev U.S. G ode Printed in U.S.. GLNIR, IN IR WY GLNL, X

7 Wall Mount, Slotted Series III Type ctive Receptacle onnector with Glenair Size 8 Opto-electronic s Opto-lectronic ctive MIL-TL type wall-mount slotted receptacle R OLOR N PR 38999/ MX R2 S PG ±.010 R2 SS (.175) THR.613± Wall Mount, Slotted (38999/20) Table XII: imensions for Slotted Receptacles ode Thread Per M38999/20 SS sq ± P-.3L-TS (26.2) P-.3L-TS (33.3) P-.3L-TS (36.5) G P-.3L-TS (39.7) H P-.3L-TS (42.9) J P-.3L-TS (46.0) Ø (RONT MOUNT) (RONT MOUNT) ø ode Shell Size Table XI: Recommended Panel ut-out Ø ±.005 Ø min Ø min per R2 per (3.3).796 (20.2).800 (20.3) (20.6).719 (18.3) (3.3) (31.0) (29.7) (27.0) (24.6) (3.3) (32.9) (32.4) (29.4) (27.0) G (3.3) (36.1) (32.4) (31.8) (29.4) H (3.9) (39.3) (38.7) (34.9) (31.8) J (3.8) (42.5) (43.2) (38.1) (34.9) Ø ROMMN PNL UT-OUT OR RONT PNL MOUNTING S N 00 WLL MOUNT RPTLS (NOT TO SL) (RR MOUNT) (RR MOUNT) ø ROMMN PNL UT-OUT OR K PNL MOUNTING S N 00 WLL MOUNT RPTLS (NOT TO SL) 2013 Glenair, Inc. Rev U.S. G ode Printed in U.S.. GLNIR, IN IR WY GLNL, X

8 Opto-lectronic Jam Nut Series III Type ctive Receptacle onnector with Glenair Size 8 Opto-electronic s ctive MIL-TL type jam nut receptacle ø UU WW R OLOR N MX THR 07 - Jam Nut Mount (38999/24) Y THR.511±.010 (.175) ode Table XII: imensions for linch Nut and Slotted Receptacles Thread Per M38999/20 Y Thread Per M38999/24 ØUU ±.010 WW sq ± P-.3L-TS-2 M20 X 1.0-6g 0.100R (35.0) (32.0) P-.3L-TS-2 M32 X 1.0-6g 0.100R (44.5) (41.3) P-.3L-TS-2 M35 X 1.0-6g 0.100R (49.2) (46.3) G P-.3L-TS-2 M38 X 1.0-6g 0.100R (52.4) (49.3) H P-.3L-TS-2 M41 X 1.0-6g 0.100R (55.6) (52.7) J P-.3L-TS-2 M44 X 1.0-6g 0.100R (58.7) (55.6) ode Table XI: Recommended Panel ut-out Ø (min) Per M38999/24 ±.005 Ø min Per M38999/24 ± (21.1) (19.5) (32.1) (30.6) (35.3) (33.8) G (38.5) (37.0) H (41.7) (47.0) J (44.8) (43.3) ø -- ROMMN PNL UT-OUT OR JM NUT RPTL (NOT TO SL) 2013 Glenair, Inc. Rev U.S. G ode Printed in U.S.. GLNIR, IN IR WY GLNL, X