Easy Fit SmartPhone alarm system (HSA6092) V3 onward

Transcription

1 Easy Ft SmartPhone alarm system (HSA6092) V3 onward Installaton Programmng Operatng Keep ths manual safe for reference and future mantenance Introducton Contents Thank you for choosng the Wreless Alarm System. Ths smple to nstall system has been desgned wth the user n mnd. All the components are self contaned and no connectons are needed between the unts. There s no need to damage the home decor, lft carpets or run cables. You can nstall up to 40 devces (Max. 6 PIR Cameras) n ths system. As well as extra door/wndow contacts, PIRs and smoke detectors, you can add keyfob remote controls and keypads for added control convenence. There s no need to wre nto the mans supply or seek the servces of a qualfed electrcan. The control box s powered by an adaptor and all other components are powered by battery (all batteres ncluded). Batteres wll operate for 2 years or more before they need changng. Regular testng and battery changes (when notfed by the system) wll ensure relablty and peace of mnd. The securty detectors and external sren are tamper protected. Any unauthorsed tamperng wth these tems when the system s armed wll result n an alarm. Dsplay extreme cauton when usng ladders or steps, please follow manufacturer s nstructons. Be careful when usng hand and power tools and follow the manufacturer s gudelnes when usng them. Take care that the correct tools are used. Wear goggles or protectve clothng where requred. The external Sren s extremely loud, please ensure you replace the cover and retreat to a safe dstance before testng. 1 Locaton plannng 2 2 Unpack all the parts 4 3 Intal set-up 6 4 Mountng Devces 8 5 Usng the System 11 Addng and usng Accessores 13 Changng the batteres 15 Troubleshootng 17 Specfcatons 18 Recommended Installaton Sequence We recommend you follow the smple nstall sequence, headngs numbered 1-5. The dallng facltes must only be used wth persons who have consented to beng contacted by the system. The system s not to be used to make 999 emergency calls drectly. do not hold responsblty for any actons taken by emergency servces for ncorrect use of the dallng faclty. Informaton and llustratons are subject to change wthn ths document. reserves the rght to alter the specfcaton and product desgn at anytme wthout notce. s a regstered trademark ASSA ABLOY. All rghts reserved.

2 Locaton plannng 1Work out the best places to locate the devces for maxmum protecton. Havng chosen the locatons do not mount at ths stage. Home and Away Mode Plannng The home armng mode allows the premses to be part armed so that no one can get nsde wthout warnng the occuper, yet the person already nsde the house can move freely wthout trggerng the alarm. For example the downstars of a house can be armed whle upstars can be dsarmed allowng the user to go to bed wthout causng an alarm. If ths feature s to be used, then t should be planned now, before nstallaton. Decde what areas can be occuped when n home armng mode, the sensors for these areas should have ts attrbute set to Home Omt (see page 11); and the sensors actvated on the path to access the control unt should be to be set to Home access. Keypad Remote Control Accessory The remote keypad s deal n the front entrance, bedrooms or at the top of a starwell so the ground floor can be armed when gong to bed for the nght. Or, at a sde or back door for alternatve entry. Mount at chest heght for ease of use Desgned for ndoor use only Keypad should be accessble from a protected entry/ext pont Ensure that the keypad s not vsble from the outsde of the premses. Operatng Range All devces must be wthn 30 metres of the control unt and must not be mounted on or near large metal objects. Avod obvous sources of electrcal nterference such as frdges and mcrowave ovens Tamper Swtches When mountng devces ensure that any tamper swtches close fully. On uneven surfaces t may be necessary to place packng behnd the swtch for relable operaton. Extend the System Extend the system n the future to ncrease your securty or as your needs change. For example, add extra PIR detectors and extra door/wndow contacts. Choosng Locaton To mnmse nterference, avod locatng devces close to metal framework, glass, electrcal applances (especally wreless devces) and electrc cables. Please note that the presence of hgh densty materal (metal, glass etc) n the transmsson path wll sgnfcantly reduce the wreless transmsson range. Help Button Accessory The help button provdes extra protecton for you and your famly. When help s needed the button can actvate your alarm mmedately - even when the system s dsarmed. Mount on wall surface Desgned for ndoor use only Out of reach of chldren Hdden from vew whle easly accessble. 2

3 Y a le Smoke Detector Mount n the mddle of the celng at the top of a starwell, or on the centre of hallway celngs where smoke would most lkely be detected. Do not mount n corners or above cookng applances and heaters. Install addtonal detectors f there are closed doors preventng smoke from reachng detectors. Sren Choose a poston on an external wall where the sren would be most promnent. Mount as hgh as possble, out of easy reach. Door/Wndow Contact Select a door that wll be the man pont of entry and ext, usually your front door. Mount as hgh as possble Do not am a PIR at ths door or wndow Keyfob Remote Control Accessory Can be used nsde or outsde the property and can be kept on your keyrng. PIR Movement Detector or PIR Camera Mount n a poston such that an ntruder would normally move across the PIRs feld of vew. Heght should be between 1.9 and 2 metres above floor level. Locaton n a corner wll ensure wder room coverage. Do not mount the PIR where ts feld of vew wll be obstructed e.g. by curtans, ornaments etc. Do not pont drectly at sources of heat e.g. fres or bolers, and do not poston drectly above radators. Text Dsplay Avod mountng the PIR drectly facng a wndow. Do not pont the PIR at a door protected by a door/wndow contact. Control Box Ensure t s hdden from vew. Access to mans socket and broadband nternet router. 3

4 2 Unpack all the parts Control Box HSA6092 Unpack the kt content on a table. Remove the mountng plate (f ftted) from the control unt by sldng plate downwards. A power adaptor s suppled that plugs nto the man wall socket and control unt. Plug n the power adaptor and connect the box to your nternet router usng the cable provde. Sren HSA6050 WARNING The sren s very loud, be prepared! Take care not to actvate the sren tamper swtch unnecessarly. 1 Remove the cover by unscrewng the sngle screw located on the ld. Power swtch to ON poston. Battery Power <On Off> Learn Battery swtch Power socket Network Port (connect to Broadband Internet router) Learn button (press and hold for 3 secs) In addton to the adapter, there s a rechargeable battery nsde the control unt that serves as a backup n case of a power falure. A fully charged battery can provde backup power for a perod of at least 10 hours. It takes approxmately 72 hours to fully charge the battery. Remove the rubber battery swtch cover and locate the battery swtch. Swtch ON the nternal battery and replace the rubber cover. PIR Movement Detectors HSA Pull out the plastc pull tab on the back of the PIR. Ths wll actvate the batteres. Status LED Top LED 1 (Panel Status) Red ON: System Arm FLASH: Home Arm Green ON: Dsarm FLASH: Learn mode OFF: Walk test mode Learn/Test Button Cover screw Mddle LED 2 (Alarm & Fault Status) Red ON: Alarm been trggered FLASH: Ongong alarm event Yellow ON: Devce fault (Tamper/Low battery) FLASH: Mans power faled OFF: Normal Bottom LED 3 (Operaton Status) Yellow ON: Network problem. FLASH: Dsconnected from server Green ON: Normal Door/Wndow Contacts HSA Pull out the battery saver tab on the sde to actvate the battery. Sensor Magnet LED Learn/Test button Gap no more than 10mm 4

5 Keyfob Remote Control HSA6060 Keypad remote Remote control Control HSA6080 Remove the cover and nsert the 3 AAA alkalne 1 Pull out the plastc battery saver tab at the back of batteres as shown. The Tx LED wll flash brefly the remote keypad. Ths wll actvate the batteres. whle components ntalse. Please note, the Home button on the operatng panel and the jumper swtch nsde Panc button (do not A move) have no functon on ths model. Away / Panc button B LED Learn button= Press 8 and 9 together Dsarm HomeArm 1 Open the battery compartment usng a con by turnng cover n the drecton of the bg arrow so Keyfob remote control accessory the small arrow s next to round dot. Slde off the battery cover, nsert the 223A/MN21 Insert CR2032 battery battery as shown, and replace and replace cover. battery cover. Swtch to on. On/Off swtch Away / SmartPhone Alarm Accessores: PIR mage camera EF-PC PIR vdeo camera EF-PVC Room sensor (Temperature/Humdty) EF-RS Power swtch EF-PS Door/wndow contacts 1 Remove the Test: cover Hold for 1 second of each door/wndow contact Flash lght by loosenng the fxng screw. 2 Insert two AAA batteres nto each detector as shown. The ndcator LED wll flash brefly. Tamper swtch Jumper swtch Lght On, Test & Jumper Learn button swtch Tamper swtch 1 Insert AA/AAA batteres as suppled. Power swtch do not requre any battery. Learn/Test button Learn: Hold for 10 seconds Flash lght Camera c ah % Extenson termnals Learn/Test button Learn: Hold for 10 seconds Test: Hold for 1 second Learn: Hold for 10 seconds BackLght On: Press & release Test: Press & release Camera Learn/Test button Smoke Detector HSA Remove the cover and nsert three AA batteres Smoke detector accessory 2 The smoke detector wll now enter nto selfcalbraton mode for mnutes. It wll resume Remove normal the cover operaton and nsert after ths the perod. four AAA batteres as shown. Learn/Test Button Learn/Test button LED Help button accessory Help Button HSA3045 Remove the cover by loosenng the fxng Remove screw and the nsert cover by the loosenng 12V battery the (suppled) fxng screw as and shown. nsert Please the CR2032 ensure battery you observe (suppled) battery as shown polarty. (1). Please ensure you observe battery polarty. Magnet 1 On/Off, Test & Learn button Learn: Hold for 10 seconds Power On/Off: Press & release Test: Press & release Panc/Learn button 7 5

6 Intal set-up 3Please ensure all devces are powered and operatonal at ths pont. Download app (Smart Phone) Search term n app store: Home System Compatblty: OS 4.3+, Androd 2.2+ (wth mnmum resoluton 320x480) Internet connecton: Requred on Smart Phone Frst tme regstraton Start the app on your phone. *Due to contnuous mprovement, please note that the graphc may dffer from shown. Select New user clck here Enter your detals Panel MAC can be found on the Control box s stcker. Close app Wat for: 1) Authentcaton emal (also check spam folder) 2) SMS wth Auth code Once you have receved BOTH the authentcaton emal and SMS, clck on the emal lnk: Enter SMS Auth code. If you encounter errors, t s due to the control box not communcatng wth our server. Please check that you have connected your panel to the nternet. You wll be asked to set-up a password when regstraton s successful. Please use your emal and ths new password to logn va the front page. 6

7 Addng accessores (f you purchased extra accessores) All accessores n the kt are lnked to the control box. If you purchased extra accessores (or for some reason the accessores are deleted), please do the followng: 1 Battery Power <On Off> Learn Press and hold the learn button for at least 3 seconds. Led 1 wll now flash and beep to ndcate that you have entered learn mode 2 One by one, press the learn button on the accessores. The control box wll beep every tme a new devce s regstered Learn Button Press & hold for 3 seconds Learn button Learn button Learn HSA6020 HSA6010 button HSA3045 HSA6060 Learn button Learn button: Press 8 and 9 together Learn HSA6080 HSA3070 button HSA6050 For the followng accessores, please hold the learn button for 10 seconds before releasng to learn. Learn button Hold for 10 seconds c ah % Learn button Hold for 10 seconds EF-PC EF-PVC Learn button EF-RS EF-PS Hold for 10 seconds Learn button Hold for 10 seconds 3 Ext Learn Mode: Press and hold the control box learn button for at least 3 seconds. The LED should now stop flashng. Proceed to nstallaton. 7

8 Mountng Devces 4Tamper swtch s dsabled when system s dsarmed. Control Box Mountng The box can be free standng, ether vertcally or horzontally on a flat surface. It s also sutable for wall mountng. Usng the two holes on the mountng back plate, mark the poston of the holes. Drll two holes and fx wth the screws and plugs provded. Hook the control box onto the plate. When you are happy that all your devces can communcate wth the box, please proceed to mountng the accessores Mountng the sren Ensure the tamper swtch s fully depressed when the sren s mounted. If there s a gap, pack wth a sutable spacng materal. Check accessores range Fnd a locaton where the devce s to be mounted, see secton Locaton Plannng for suggestons. Sprng compressed frmly aganst wall Round Sren Base Wall Before proceedng to mount the devces physcally, check that the control box wll receve the system rado transmssons by dong a smple rado range test. Logn to your Home system app. Select Controller, Devce Lst then select Walk Test. Sprng Gude 1 Usng the large screws and wall plugs provded, screw the sren onto the wall through the 4 mountng holes on the sren base. 2 Fx the sren cover wth the securng screw. Mountng the PIR & PIR mage/vdeo camera 1 Open the PIR by loosenng the bottom screw. Knock out the relevant holes on the base where the plastc s thnner. The center 2 knockout holes are for flat wall mountng whle the 4 sde holes are for corner mountng. 2 Drll holes nto the wall usng the knockout holes on the base as a template. Hold the devces n the desred locaton and press the Test/Learn button (see below) on the accessores. KEYPAD: press button together for 1 second. 8 ALL OTHER DEVICES: Hold the devce n the desred locaton and press the test button for 1 second, the control box should respond wth a chme. If the sensor sgnal reached the control box, t wll show up on the last screen (see above). The rado sgnal strength s shown by a number under the devce name. Ths number ranges from 1 to 9 (strongest). Where possble please ensure devces show 3 or above for optmal performance. Battery tab Wall fxng knockouts x2 Corner fxng knockouts x4 3 Ft wall plugs and secure the PIR base wth the screws provded. 4 Ft the PIR back together and tghten bottom screw, the PIR nstallaton s complete.

9 Mountng the Keypad: degreaser agent. Please note that some surface or envronment (.e. exposure to Sunlght) may be unsutable for ths mountng method. Please use screw mountng n these cases. Battery Saver tab Wall Fxng knockouts x2 -Mountng usng screws and wall plugs Loosen the bottom screw and open the door/ wndow contact. Knock out the holes on the base as shown. Drll holes nto the mountng surface usng the holes n the knockouts on the base as template. Ft wall plugs (f requred) and secure wth the screws provded. 1 Knock out the fxng holes. Drll holes nto the wall usng the fxng holes as a template. 2 Ft wall plugs nto the wall and fx back cover wth the screws provded. Fx front of the keypad onto the back plate. Mountng the Door Contact Mountng the Help button 1 Break through the knockouts (where the plastc s thnner). 2 Usng the holes as a template, drll holes n the surface and nsert wall plugs f fxng nto plaster or brck. Screw the rear case to the wall. Replace the cover and tghten the screw. Frame Mountng the Smoke Detector Knockouts Sensor Sensor Door/Wndow Magnet Gap no more than 10mm 1 Fnd a locaton on the door/wndow where you would lke the devce to be mounted. The sensor should be on the frame whle the magnet should be on the door/wndow. Once mounted make sure the tamper swtch sprng s fully depressed. The gap between the magnet and sensor should be no more than 10mm when closed (maybe shorter dependng upon the actual envronment). Smple test to see whether the magnet s n range of the sensor: hold the magnet and sensor n place and then pull them apart. If the sensor LED lghts up t mples the two tems are wthn range. 1 The base has two mountng slots. Usng the slots as a template, drll holes and nsert the wall plugs f fxng to plaster. Screw the rear case to the celng usng the screws provded. 2 Replace the man unt onto the bracket. Mountng the Room Sensor 1 Push tab to the left to open the case. The base has two mountng slots. Usng the slots as a template, drll holes and nsert the wall plugs f fxng to plaster. Fx the base to the wall wth screws. 2 Replace the man unt onto the base. -Mountng usng adhesve pads Clean the mountng surface wth a sutable 9

10 About your alarm system (default settngs) All accessores (except EF-PC) are pre-set to entry attrbutes. When the system s frst armed, users wll have 30 seconds to ext the buldng. The System wll gnore any sensors trggerng n ths duraton. If the system s already armed, trggerng any sensors wll cause an entry countdown to begn. EF-PC/EF-PVC s default settng s Away only,.e. mmedate trggerng durng full arm and sleep durng home arm. Ths s done to conserve battery lfe When the alarm s trggered, the system wll send an emal, push notfcaton (OS only) and SMS to alert the owner. The network traffc condton wll determne how quckly the user s alerted. There may be notceable delay should the thrd party emal/sms gateway become congested. To change the ext and entry tmer, please see Controller -> Panel Settng Home armng s dsabled by default. If you need Home armng functon, see page 11. To change the attrbutes of ndvdual sensors (.e. Burglar attrbute where the ndvdual sensor wll nstantly alarm when trggered), please go to Devces Lst, then clck on sensor s settng. Each system has 20 free SMS credts, after whch reserves the rght to charge for any addtonal SMS sent. It s possble to arm the system wth open door contact (.e. wndows open). You wll be prompted on the app when tryng to arm wth your door/wndow open. Jammng and nterference detecton dsabled as default. Supervson s dsabled as default (recommended). If jammng and nterference s of concern, please enable va Controller -> Panel Settng Enable or dsable supervson detecton on the control box. PIR, Door Contact, Smoke Detector and Sren can be montored for outage usng ths feature. Except for Smoke Detector (whch s always on), the other three accessores need to have supervson enabled on board to facltate ths feature. Supervson can be enabled va Controller -> Panel Settng. Comfort LED s dsabled as default (recommended). Please enable Comfort LED va Devces -> Sren propertes (arrow on the rght). NOTE: Ths functon wll sgnfcantly reduce your Sren s battery lfe. 10

11 5 Usng the System The PIR/PIR camera have a bult-n sleep tmer to save battery power. If there s no movement n front of the PIRs for 1 mnute, the PIRs wll become ready to sgnal and movement wll now be reported. The PIRs wll sleep for 1 mnute after reportng. Changng your keypad pncode The default keypad pncode s You can set up to 6 sets of pncode by: Any movement detected n sleep tme wll not be reported and wll extend the sleep perod by a further 1 mnute. Settng up home arm mode The Home Arm mode allows the home to be partally armed so that no one can get nsde wthout frst dsarmng the system. However, the person nsde the house can move freely around wthout trggerng the alarm. Home mode s usually used to protect the ground floor when you are upstars n bed. To enable home arm, you need to choose the sensors to be gnored durng ths mode. It would typcally be the bedroom PIR etc f you want to arm your system durng the nght. These sensors should be set to Home Omt n order to be gnored durng Home Arm mode. If you wsh to trgger alarm count down wth a sensor durng Home Arm mode, please select the attrbute: Home Access. Armng and Dsarmng your alarm Usng the Home system app 11

12 Usng the keyfob (HSA6060) or keypad (HSA6080) Away Arm & Home Arm Press the Away Arm/Home Arm key on the keyfob or keypad. Dsarm Press the dsarm key on the keyfob or press the dsarm key followed by a pncode on the keypad. Manually requestng PIR mages Addng alert emal/sms You can add/delete emal and SMS phone numbers for alert durng alarm condton. Only Burglar events wll be reported va SMS, whle you can choose to have ALL events (or Burglar only) reported va emal. Hnt: our report emal wll use the emal address of: report@yalehomesystem.co.uk Save ths emal address as your VIP (Apple OS) or Prorty (Androd) emal and assgn a specal rngtone to t. Durng an alarm, the PIR mage/vdeo camera wll send mages/vdeo to your phone. You can also manually request these mages/vdeo. Stll mages take an average of 15 seconds before showng on your phone, and vdeo takes approxmately 1 mnute. Clck on mage to vew mages/vdeos. Note: Up to 50 mages/vdeos can be kept n the Server (the oldest mages/vdeos are automatcally deleted to make space). Users are advsed to delete unwanted mages/vdeos. Controllng Dgtal door lock Ths s a reserved functon for use wth our Dgtal door lock. We wll shortly be launchng a module compatble wth our Dgtal door lock range. 12

13 Addng and usng Accessores To provde addtonal protecton you can add extra door/wndow contacts, PIRs, keyfob remote controls, keypad remote controls, help buttons and smoke detectors. These are avalable separately from your local stockst. Addng accessores to your system See page 7 Usng your keyfob The keyfob can be used to Away Arm, Home Arm, and Dsarm the system usng the buttons as shown. An emergency alarm can be actvated by pressng the emergency button for 3 seconds untl LED stops flashng. An emergency alarm can only be stopped by usng the control unt keypad or a remote keypad. Away / Keypad Keypad ntalsaton If you purchase a keypad as an accessory, you wll need to ntalse t pror to use wth the control panel. 1 Press Panc button A followed by factory default keypad code 0000 (ths s dfferent to your control panel pncode). 2 The LED wll now flash slowly ndcatng t s n test (programmng) mode. 3 Press Panc button A followed by the 7 key to set the keypad nto control panel system mode (also known as slave mode). 4 Qut test mode by pressng the dsarm key twce. The keypad code and mode settng has been completed. The keypad wll now use the same pncode that s set for the control panel unt. Away / Panc button A Panc button B LED Learn button= Press 8 and 9 together Dsarm HomeArm Forgotten keypad code (dfferent to dsarmng pncode) If the keypad code s accdentally forgotten, the keypad can be reset to factory default (0000) usng the followng steps: 1 Unscrew the two keypad case screws and remove keypad back cover (please dsable tamper frst). Locate and remove the battery. 2 Press the number 4 key at the same tme as rensertng the battery. 3 Screw the keypad case together and re-learn the keypad nto the system usng the steps descrbed above n ths secton. 13

14 Usng your keypad The keypad can be used to Away Arm and Home Arm the system usng the buttons as shown. The system s dsarmed by pressng the dsarm button followed by any user code. An emergency alarm can be actvated by pressng the panc A and B buttons smultaneously. Deactvate panc event by pressng the dsarm button followed by any user code. If there s a system fault. you wll need to press the arm/home arm button for a second tme to force arm the system. Usng your smoke detector Smoke Detecton When smoke s detected the devce wll actvate for a mnmum of 10 seconds wth a two tone alarm and flashng LED for a local fre alarm. The detector wll send a rado sgnal to the control unt for actvatng a system fre alarm. Usng your Help Button Actvate an Alarm Press and hold the red button for at least 3 seconds. The LED wll lght momentarly and the alarm wll be actvated. Slence an Alarm Press and hold down the red button for 10 seconds. The LED wll lght momentarly for a second tme and the alarm wll be slenced. Please note that slencng the alarm wth the help button does not reset the system. If the alarm s armed pror to actvaton, the system wll re-arm after beng slenced wth the help button. The system wll requre a reset at the control unt after beng slenced wth the help button. Pressng the test button when n an alarm condton wll slence the alarm for 10 mnutes. It wll automatcally resume smoke detecton agan after ths perod. If the smoke densty s stll over the alarm threshold, then the smoke detector wll reman n an alarm condton and t wll repeat the local fre alarm wth a rado fre alarm sgnal to the control unt. Testng Smoke detector testng should be done on a regular monthly bass. Pressng the test button wll make the LED flash, the audble sounder chme and wll send a rado test sgnal to the control unt when the button s released. If nothng happens after pressng the test button, t ndcates the batteres wll need changng. Recalbraton The smoke detector mght need recalbratng after tme to ensure t s workng at ts optmum. Ths s done by pressng and holdng the test button untl the LED flashes and beeps after 10 seconds. The detector wll then start ts self calbraton routne. 14

15 Changng the Batteres Always use correct type of batteres as replacements because any other battery can cause problems wth the operaton of the system. Typcal lfe of batteres s two years or more. Ensure the correct steps are taken when changng batteres n tamper protected devces. Low Battery Indcaton The app wll dsplay the low battery message under the actual devce. PIR & PIR Camera Battery Change When the battery s low the LED wll flash when any movement s detected. The batteres are changed as follows: 1 Ensure the system s dsarmed. 2 Loosen the case screw and remove PIR sensor from base to reveal the batteres. 3 Insert new batteres (Note: PIR camera requres 1.5V AA Alkalne batteres) observng correct polarty. The PIR LED wll flash for 30 seconds whle ntalsng. 4 Reft sensor on base and tghten bottom case screw. Swtch tamper protecton back on. When a devce frst shows the low battery sgnal t has enough battery capacty to operate for a further month before complete exhauston. Sren Battery Change When the batteres start gettng low the sren wll produce a seres of pps and flashes durng armng and dsarmng. 1 Select Controller, Devce Lst, clck sren s propertes (con on the rght) and set sren tamper to the OFF poston. 2 Remove the sren ld and swtch the sren power swtch to OFF. 3 Unscrew the four screws on the battery compartment ld and remove the cover. 4 Remove the four batteres, wat for 30 seconds, and replace them wth four fresh alkalne D cells. 5 Swtch on sren power and check that the sren beeps and flashes. Warnng: After the batteres have been nserted, the tamper wll become actve after three hours. Please replace the cover back onto the sren quckly. Sren case tamper condtons are also sgnalled by a seres of beeps when the system s armed but not when the system s dsarmed (low battery warnng produces a seres of pps when armed and dsarmed), take care not to confuse the two dfferent condtons. PIR case tamper condtons are also ndcated by a flashng LED, check the tamper before changng the batteres. Door/Wndow Sensor Battery Change When the battery s low the LED wll lght up when the door/wndow s opened. The battery s changed as follows: 1 Ensure the system s dsarmed. 2 Loosen the case screw and remove door/wndow sensor from base to reveal battery. 3 Usng a screwdrver gently lever out the old battery. 4 Insert new CR2032 con cell wth the + sde uppermost. 5 Press battery nto holder frmly wth fnger and thumb untl a clck s heard. 6 Reft sensor on base and tghten bottom case screw. Swtch tamper protecton back on. Door/wndow sensor case tamper condtons are also ndcated by a lt LED, check the tamper before changng the battery. 15

16 Keyfob Battery Change When the battery s low the LED wll glow dmly when any key s pressed. The battery s changed as follows: 1 Usng a con turn the battery cover antclockwse to the unlocked poston and remove cover and battery. 2 Insert new CR2032 con cell wth the + sde uppermost. 3 Replace battery cover. Press any key and check that the LED lghts. If the LED lghts the new battery nstallaton s successful. Keypad Battery Change When the battery s low the LED wll flash when any key s pressed. The battery s changed as follows: 1 Ensure the system s dsarmed. 2 Unscrew the two keypad case screws and remove keypad back to reveal battery. 3 Usng a screwdrver gently lever out the old battery. 4 Insert new CR2032 con cell wth the + sde uppermost. 5 Press battery nto holder frmly wth fnger and thumb untl a clck s heard. 6 Press a number key and check that the LED lghts. If the LED lghts the new battery nstallaton s successful, screw keypad back on and the battery change s complete. Help Button Battery Change When the battery s low the LED wll glow dmly when the button s pressed. The battery s changed as follows: 1 Loosen the bottom case screw and take button cover off base. 2 Insert new CR2032 con cell wth the + sde uppermost. 3 Replace button cover. Press the button and check that the LED lghts. If the LED lghts the new battery nstallaton s successful. Smoke Detector Battery Change When the battery s low the LED wll flash accompaned wth a Low-volume beep once every 30 seconds. 1 Rotate smoke detector ant-clockwse to detach from base bayonet fxng. 2 Insert new AA alkalne batteres, takng care to observe polarty and wat mnutes for he smoke detector to recalbrate tself, ndcted by a rapdly flashng LED.. 3 Replace smoke detector on base and rotate clockwse to lock. 4 Press the test button and check that the LED lghts and the sounder chmes. 16

17 Troubleshootng For onlne assstance, please vst: Sren Sren does not respond to armng or dsarmng Sren batteres are completely exhausted. Check sren batteres by removng sren cover, f there s no tamper alarm when removed, replace batteres wth new alkalne equvalents. Sren not learnt-n. If sren produces a tamper alarm when the cover s removed and sren s OK, learn-n the sren. Sren out of range. Sren produces a 3 second alarm when dsarmed There has been a prevous alarm and there mght be an ntruder stll n the premses. Sren produces a seres of pps when armed or dsarmed the sren If produces a seres of pps when armng and dsarmng ths ndcate low batteres. the sren If produces a seres of pps only when armng ths ndcates a tamper fault. Check that the sren cover s frmly secured and the tamper swtch plunger s n contact wth the wall. If not use sutable packng materal to fll gap. Sren produces an nterrupted tone when soundng an alarm The sren has low batteres. Change batteres wth new alkalne replacements. PIR PIR does not respond to movement Prevous movement has trggered the PIR sleep tmer and s preventng subsequent movement detecton. Arm system and vacate protected room for at least 1.5 mnutes before testng. PIR s slow to respond Ths s normal, the PIR has sophstcated false alarm flterng that wll flter out random fluctuatons and responds to genune movement across feld of vew, t s less senstve walkng drectly towards t. PIR gves false alarms Check pets have no access to protected area. Check that PIR s not ponted at sources of heat or movng objects, e.g. flutterng curtans. Check that PIR s not mounted above convector heaters or pontng drectly at wndows. PIR LED flashes Batteres are low or the tamper swtch s dsturbed. Check that the tamper swtch sprng s makng contact wth base. If the tamper swtch s OK, change batteres wth new alkalne replacements. PIR does not respond to movement Batteres are completely exhausted. Door Contact Door contact LED lghts up Batteres are low or the tamper swtch dsturbed. Check that the tamper swtch sprng s makng contact wth the mountng surface. If the tamper swtch s OK, please change battery. Door contact does not respond to door openng when jumper s n test poston Batteres are completely exhausted. Change batteres wth new CR2032 con cell replacements. The magnet s too far away from the door contact. Check that the gap between door contact and magnet s not greater than 8mm. PIR mage/vdeo Camera PIR Camera LED flashes every 5 seconds PIR Camera s ether not n range of the control box or not learnt nto the system. * If a PIR Camera s not learnt nto the system or wthn range of the control box, battery lfe wll be Control box s LED 2 (Warnng LED) Red Yellow ON: Alarm been trggered. Arm and then dsarm the system once more wll clear ths LED. FLASH: Ongong alarm event ON: Devce fault (Tamper/Low battery) FLASH: Mans power faled OFF: Normal 17

18 Specfcatons All devces Envronmental condtons -10 C to 40 C, relatve humdty 70% non-condensng for all unts except the external sren. Sren: -20 C to 50 C, relatve humdty 95% non-condensng Rado operatonal range 30m n a typcal domestc nstallaton, range can vary dependng on buldng constructon, devce postons and RF envronment Housngs Control box ABS/polycarbonate Sren Output 100dBA sound 1m mnmum Zones 20 rado devces Rado system 433MHz AM, 2.4GHz Power supply Plug top adaptor type, nput 230VAC 50Hz, output 9VDC, 1A, tested to EN Rechargeable battery N-MH, 4.8V 1100mAH, charge tme 72hrs, standby tme 10hrs Sren Sren output 104dBA sound 1m mnmum Rado 433MHz AM Power supply 6V, 4 x D alkalne cells. 2.5 years typcal servce lfe Passve nfra red (PIR) Detector Alarm processng Mcroprocessor controlled dual edge sequental pulse count wth pulse length dscrmnaton Rado 433MHz AM Power supply 4.5V, 3 x AAA alkalne cells. 2 years typcal domestc servce lfe wthout supervson. Movement detecton range 12m, 110 PIR mage camera Alarm processng Mcroprocessor controlled dual edge sequental pulse count wth pulse length dscrmnaton Rado 2.4GHz Power supply 2 x AA 1.5V Alkalne cells. 2 years+ typcal domestc servce lfe. Movement detecton range 12m, 110 Door/wndow contact Rado 433MHz AM Power supply 3V, CR2032 lthum con cell. 2 years typcal domestc servce lfe wthout supervson. Smoke detector Rado 433MHz AM Power supply 4.5V, 3 x AA alkalne cells. 3 years typcal domestc servce lfe Tested to EN54 Keyfob remote control Rado 433MHz AM Power supply 3V, CR2032 lthum con cell. 3 years typcal domestc servce lfe Keypad remote control Rado 433MHz AM Power supply 3V, CR2032 lthum con cell. 3 years typcal domestc servce lfe Help button Rado 433MHz AM Power supply 3V, CR2032 lthum con cell. 3 years typcal domestc servce lfe 18

19 ASSA ABLOY Ltd. School Street, Wllenhall West Mdlands England, WV13 3PW ASSA ABLOY Ltd. School Street Wllenhall West Mdlands England WV13 3PW Model: HSA3400 HSA3020 HSA3060 HSA3010 HSA3050 HSA3045 HSA3080 HSA3030 HSA3070 EN / V2.3.1 (2010) EN / V2.3.1 (2010) EN / V1.8.1 (2008) EN / V (2002) EN / A11 : A1: A12:2011 John Ward Drector Date: 15/04/13 On behalf of ASSA ABLOY Ltd

20 WARRANTY AUSTRALIAN CONSUMER LAW GUARANTEES Securty Merchants Pty Ltd ABN ( SECURITY MERCHANTS ) guarantees all of ts YALE branded products n accordance wth the Australan Consumer Law. YALE WARRANTY 1. Warranty - SECURITY MERCHANTS also warrants that each of ts YALE branded products wth whch ths document s gven wll be free of defects n materal and workmanshp (ncludng mechancal parts) for a perod of 2 years from the date of purchase of the product, subject to the lmtatons and exclusons set out below ("Warranty"). 2. Lmtatons - Unless otherwse expressly provded for n wrtng and subject to the exclusons set out n ths Warranty: a. Electrcal and Electronc Components - Electrcal and electronc components used n SECURITY MERCHANTS's YALE branded products (excludng batteres) are warranted wll be free of defects n materal and workmanshp for a perod of 2 years from the date of purchase. Batteres are not covered by the Warranty. b. Fnsh The Warranty does not apply to the fnshes of YALE branded products nor to cosmetc or appearance damage. 3. Clamng on the Warranty (a). If you purchased a YALE branded product from a retaler or other reseller (as opposed to drect from SECURITY MERCHANTS) and wsh to clam on the Warranty to the retaler or other reseller, you must, at your own expense: a. return the product securely packed to protect aganst damage to the product; and b. provde detals of: I. the clam on the Warranty; II. proof of orgnal purchase; and III. your name, address, emal address (f you have one) and telephone number; to the retaler or other reseller from whom you orgnally purchased the product, wthn the respectve warranty perod referred to above.. (A) If you purchased a YALE branded product drect from SECURITY MERCHANTS or otherwse wsh to clam on the Warranty drect to SECURITY MERCHANTS, you must, at your own expense:. frst contact the SECURITY MERCHANTS Customer Servce Department at the contact detals below to: a. provde SECURITY MERCHANTS wth detals of the clam on the Warranty; b. organse to provde SECURITY MERCHANTS wth proof of orgnal purchase; and c. obtan a Case Number;. securely pack the product to protect aganst damage to the product;. nclude a copy of the orgnal proof of purchase n the packagng;