2-Way Wireless Security Suite v1.0 Installation Guide

Transcription

1 2-Way Wreless Securty Sute v1.0 Installaton Gude Models: PC /868 PC9155G-433/868 PC9155D-433/868 Used wth: WT /868 WT5500P-433/868 Seres 2-way Wreless Keypad TELEPERMIT These DSC Securty Alarm Systems may be connected to the Telecom Network PTC 211 / 09 /017 PC PTC 211 / 09 /018 PC9155D-433 PTC 211 / 09 /019 PC9155G-433 RN = 0.5 N11427 IMPORTANT: Ths manual contans nformaton on lmtatons regardng product use and functon and nformaton on the lmtatons as to lablty of the manufacturer. The entre manual should be carefully read.

2 SAFETY INSTRUCTIONS FOR SERVICE PERSONNEL WARNING: WHEN USING EQUIPMENT CONNECTED TO THE TELEPHONE NETWORK, THERE ARE BASIC SAFETY INSTRUCTIONS THAT SHOULD ALWAYS BE FOLLOWED. REFER TO THE SAFETY INSTRUCTIONS PROVIDED WITH THIS PRODUCT; SAVE THEM FOR FUTURE REFERENCE. INSTRUCT THE END-USER REGARDING THE SAFETY PRECAUTIONS THAT SHALL BE OBSERVED WHEN OPERATING THIS EQUIPMENT. Selectng a Sutable Locaton for the Alarm Controller Use the followng lst as a gude to fnd a sutable place for ths equpment: Locate the control panel near a telephone socket and a power outlet. Select a place that s free from vbraton and shocks. Place the alarm controller on a flat, stable surface and follow the nstallaton nstructons. Do NOT locate ths product where persons wll walk on the secondary crcut cable(s). Do NOT connect the alarm controller to electrcal outlets on the same crcut as large applances. Do NOT select a place that exposes your alarm controller to drect sunlght, excessve heat, mosture, vapors, chemcals or dust. Do NOT nstall ths equpment near water. (e.g., bath tub, wash bowl, ktchen/laundry snk, n a wet basement, or near swmmng pools, etc.). Do NOT nstall ths equpment and ts accessores n areas where there s a rsk of exploson. Do NOT connect ths alarm controller to electrcal outlets controlled by wall swtches or automatc tmers. AVOID sources of rado nterference. AVOID settng up the equpment near heaters, ar condtoners, ventlators, and/or refrgerators. AVOID locatng ths equpment close to or on top of large metal objects (e.g., metal wall studs). Safety Precautons Requred Durng Installaton NEVER nstall ths equpment and/or telephone wrng durng a lghtnng storm. NEVER touch unnsulated telephone wres or termnals unless the telephone lne has been dsconnected at the network nterface. Ensure that cables are postoned so that accdents can not occur. Connected cables must not be subject to excessve mechancal stran. For Drect Plug-n versons, use the transformer suppled wth the devce. WARNING (Drect plug-n versons only) THIS EQUIPMENT HAS NO MAINS ON/OFF SWITCH. THE PLUG OF THE DIRECT PLUG-IN POWER SUPPLY IS INTENDED TO SERVE AS THE DISCONNECTING DEVICE IF THE EQUIPMENT MUST BE QUICKLY DISCONNECTED. IT IS IMPERATIVE THAT ACCESS TO THE MAINS PLUG AND ASSOCIATED MAINS SOCKET/OUTLET, IS NEVER OBSTRUCTED. IMPORTANT NOTE! The PC9155 Alarm System shall be nstalled and used wthn an envronment that provdes the polluton degree max 2 and overvoltages category II NON-HAZARDOUS LOCATIONS, ndoor only. The equpment s DIRECT PLUG-IN (external transformer) or PER- MANENTLY CONNECTED (See Fgure 2-3: Mountng & Wrng Detals) and s desgned to be nstalled, servced and/or repared by servce persons only; [servce person s defned as a person havng the approprate techncal tranng and experence necessary to be aware of hazards to whch that person may be exposed n performng a task and of measures to mnmze the rsks to that person or other persons]. There are no parts replaceable by the end-user wthn ths equpment. The wrng (cables) used for nstallaton of the Alarm System and accessores, shall be nsulated wth PVC, TFE, PTFE, FEP, Neoprene or Polyamde. (a) The equpment enclosure must be secured to the buldng structure before operaton. (b) Internal wrng must be routed n a manner that prevents: - Excessve stran or loosenng of wre on termnal connectons; - Damage of conductor nsulaton (c) Dsposal of used batteres shall be made n accordance wth local waste recovery and recyclng regulatons. (d) Before servcng, DISCONNECT the power and telephone connecton. (e) DO NOT route any wrng over crcut boards. (f) It s the nstaller s responsblty to ensure that a readly accessble dsconnect devce s ncorporated n the buldng for permanently connected nstallatons. The power supply must be Class II, FAIL SAFE wth double or renforced nsulaton between the PRIMARY and SECONDARY crcut/enclo- SURE and be an approved type acceptable to the local authortes. All natonal wrng rules shall be observed.

3 Gudelnes for Locatng Smoke & CO Detectors The followng nformaton s for general gudance only and t s recommended that local fre codes and regulatons be consulted when locatng and nstallng smoke alarms and CO Alarms. Smoke Detectors Research ndcates that all hostle fres n homes generate smoke to a greater or lesser extent. Detectable quanttes of smoke precede detectable levels of heat n most cases. Smoke alarms should be nstalled outsde of each sleepng area and on each storey of the home. DSC recommends that addtonal smoke alarms beyond those requred for mnmum protecton be nstalled. Addtonal areas that should be protected nclude: the basement; bedrooms, especally where smokers sleep; dnng rooms; furnace and utlty rooms; and any hallways not protected by the requred unts. On smooth celngs, detectors may be spaced 9.1m (30 feet) apart as a gude. Other spacng may be requred dependng on celng heght, ar movement, the presence of josts, unnsulated celngs, etc. Consult Natonal Fre Alarm Code NFPA 72, CAN/ULC-S553-M86 or other approprate natonal standards for nstallaton recommendatons. Do not locate smoke detectors at the top of peaked or gabled celngs; dead ar space n these locatons may prevent smoke detecton. Avod areas wth turbulent ar flow, such as near doors, fans or wndows. Rapd ar movement around the detector may prevent smoke from enterng the unt. Do not locate detectors n areas of hgh humdty. Do not locate detectors n areas where the temperature rses above 38 o C (100 o F) or falls below 5 o C (41 o F). Smoke detectors should always be nstalled n accordance wth NFPA 72, the Natonal Fre Alarm Code. Smoke detectors should always be located n accordance wth: Smoke detectors shall be nstalled outsde of each separate sleepng area n the mmedate vcnty of the bedrooms and on each addtonal storey of the famly lvng unt, ncludng basements and excludng crawl spaces and unfnshed attcs. In new constructon, a smoke detector also shall be nstalled n each sleepng room. Splt level arrangement: Smoke detectors are requred where shown. Smoke detectors are optonal where a door s not provded between lvng room and recreaton room Makuuhuone Makuuhuone Makuuhuone Fgure 1 Kettö Olohuone Fgure 2 Fgure 3 Kuva 1 Fgure 3a Fgure 4 CO Detectors CO gas moves freely n the ar. Suggested locatons are n or as near as possble to sleepng areas of the home. The human body s most vulnerable to the effects of CO gas durng sleepng hours. For maxmum protecton, a CO alarm should be located outsde prmary sleepng areas or on each level of your home. Fgure 5 ndcates the suggested locatons n the home. The electronc sensor detects carbon monoxde, measures the concentraton and sounds a loud alarm before a potentally harmful level s reached. Do NOT place the CO alarm n the followng areas: Where the temperature may drop below -10ºC or exceed 40 ºC. Near pant thnner fumes Wthn 5 feet (1.5 meter) of open flame applances such as furnaces, stoves and freplaces In exhaust streams from gas engnes, vents, flues or chmneys Do not place n close proxmty to an automoble exhaust ppe; ths wll damage the detector BEDROOM GROUND FLOOR BEDROOM BASEMENT BEDROOM KITCHEN CARBON MONOXIDE DETECTOR Fgure 5 GARAGE

4 Dgtal Securty Controls warrants the orgnal purchaser that for a perod of twelve months from the date of purchase, the product shall be free of defects n materals and workmanshp under normal use. Durng the warranty perod, Dgtal Securty Controls shall, at ts opton, repar or replace any defectve product upon return of the product to ts factory, at no charge for labour and materals. Any replacement and/or repared parts are warranted for the remander of the orgnal warranty or nnety (90) days, whchever s longer. The orgnal purchaser must promptly notfy Dgtal Securty Controls n wrtng that there s defect n materal or workmanshp, such wrtten notce to be receved n all events pror to expraton of the warranty perod. There s absolutely no warranty on software and all software products are sold as a user lcense under the terms of the software lcense agreement ncluded wth the product. The Customer assumes all responsblty for the proper selecton, nstallaton, operaton and mantenance of any products purchased from DSC. Custom products are only warranted to the extent that they do not functon upon delvery. In such cases, DSC can replace or credt at ts opton. Internatonal Warranty The warranty for nternatonal customers s the same as for any customer wthn Canada and the Unted States, wth the excepton that Dgtal Securty Controls shall not be responsble for any customs fees, taxes, or VAT that may be due. Warranty Procedure To obtan servce under ths warranty, please return the tem(s) n queston to the pont of purchase. All authorzed dstrbutors and dealers have a warranty program. Anyone returnng goods to Dgtal Securty Controls must frst obtan an authorzaton number. Dgtal Securty Controls wll not accept any shpment whatsoever for whch pror authorzaton has not been obtaned. Condtons to Vod Warranty Ths warranty apples only to defects n parts and workmanshp relatng to normal use. It does not cover: damage ncurred n shppng or handlng; damage caused by dsaster such as fre, flood, wnd, earthquake or lghtnng; damage due to causes beyond the control of Dgtal Securty Controls such as excessve voltage, mechancal shock or water damage; damage caused by unauthorzed attachment, alteratons, modfcatons or foregn objects; damage caused by perpherals (unless such perpherals were suppled by Dgtal Securty Controls Ltd.); defects caused by falure to provde a sutable nstallaton envronment for the products; damage caused by use of the products for purposes other than those for whch t was desgned; damage from mproper mantenance; damage arsng out of any other abuse, mshandlng or mproper applcaton of the products. Lmted Warranty WARNING - READ CAREFULLY Items Not Covered by Warranty In addton to the tems whch vod the Warranty, the followng tems shall not be covered by Warranty: () freght cost to the repar centre; () products whch are not dentfed wth DSC's product label and lot number or seral number; () products dsassembled or repared n such a manner as to adversely affect performance or prevent adequate nspecton or testng to verfy any warranty clam. Access cards or tags returned for replacement under warranty wll be credted or replaced at DSC's opton. Products not covered by ths warranty, or otherwse out of warranty due to age, msuse, or damage shall be evaluated, and a repar estmate shall be provded. No repar work wll be performed untl a vald purchase order s receved from the Customer and a Return Merchandse Authorzaton number (RMA) s ssued by DSC's Customer Servce. Dgtal Securty Controls Ltd. s lablty for falure to repar the product under ths warranty after a reasonable number of attempts wll be lmted to a replacement of the product, as the exclusve remedy for breach of warranty. Under no crcumstances shall Dgtal Securty Controls be lable for any specal, ncdental, or consequental damages based upon breach of warranty, breach of contract, neglgence, strct lablty, or any other legal theory. Such damages nclude, but are not lmted to, loss of profts, loss of the product or any assocated equpment, cost of captal, cost of substtute or replacement equpment, facltes or servces, down tme, purchaser s tme, the clams of thrd partes, ncludng customers, and njury to property. The laws of some jursdctons lmt or do not allow the dsclamer of consequental damages. If the laws of such a jursdcton apply to any clam by or aganst DSC, the lmtatons and dsclamers contaned here shall be to the greatest extent permtted by law. Some states do not allow the excluson or lmtaton of ncdental or consequental damages, so that the above may not apply to you. Dsclamer of Warrantes Ths warranty contans the entre warranty and shall be n leu of any and all other warrantes, whether expressed or mpled (ncludng all mpled warrantes of merchantablty or ftness for a partcular purpose) and of all other oblgatons or labltes on the part of Dgtal Securty Controls. Dgtal Securty Controls nether assumes responsblty for, nor authorzes any other person purportng to act on ts behalf to modfy or to change ths warranty, nor to assume for t any other warranty or lablty concernng ths product. Ths dsclamer of warrantes and lmted warranty are governed by the laws of the provnce of Ontaro, Canada. WARNING: Dgtal Securty Controls recommends that the entre system be completely tested on a regular bass. However, despte frequent testng, and due to, but not lmted to, crmnal tamperng or electrcal dsrupton, t s possble for ths product to fal to perform as expected. Out of Warranty Repars Dgtal Securty Controls wll at ts opton repar or replace out-of-warranty products whch are returned to ts factory accordng to the followng condtons. Anyone returnng goods to Dgtal Securty Controls must frst obtan an authorzaton number. Dgtal Securty Controls wll not accept any shpment whatsoever for whch pror authorzaton has not been obtaned. Products whch Dgtal Securty Controls determnes to be reparable wll be repared and returned. A set fee whch Dgtal Securty Controls has predetermned and whch may be revsed from tme to tme, wll be charged for each unt repared. Products whch Dgtal Securty Controls determnes not to be reparable wll be replaced by the nearest equvalent product avalable at that tme. The current market prce of the replacement product wll be charged for each replacement unt. Note to Installers Ths warnng contans vtal nformaton. As the only ndvdual n contact wth system users, t s your responsblty to brng each tem n ths warnng to the attenton of the users of ths system. System Falures Ths system has been carefully desgned to be as effectve as possble. There are crcumstances, however, nvolvng fre, burglary, or other types of emergences where t may not provde protecton. Any alarm system of any type may be compromsed delberately or may fal to operate as expected for a varety of reasons. Some but not all of these reasons may be: Inadequate Installaton A securty system must be nstalled properly n order to provde adequate protecton. Every nstallaton should be evaluated by a securty professonal to ensure that all access ponts and areas are covered. Locks and latches on wndows and doors must be secure and operate as ntended. Wndows, doors, walls, celngs and other buldng materals must be of suffcent strength and constructon to provde the level of protecton expected. A reevaluaton must be done durng and after any constructon actvty. An evaluaton by the fre and/or polce department s hghly recommended f ths servce s avalable. Crmnal Knowledge Ths system contans securty features whch were known to be effectve at the tme of manufacture. It s possble for persons wth crmnal ntent to develop technques whch reduce the effectveness of these features. It s mportant that a securty system be revewed perodcally to ensure that ts features reman effectve and that t be updated or replaced f t s found that t does not provde the protecton expected. Access by Intruders Intruders may enter through an unprotected access pont, crcumvent a sensng devce, evade detecton by movng through an area of nsuffcent coverage, dsconnect a warnng devce, or nterfere wth or prevent the proper operaton of the system. Power Falure Control unts, ntruson detectors, smoke detectors and many other securty devces requre an adequate power supply for proper operaton. If a devce operates from batteres, t s possble for the batteres to fal. Even f the batteres have not faled, they must be charged, n good condton and nstalled correctly. If a devce operates only by AC power, any nterrupton, however bref, wll render that devce noperatve whle t does not have power. Power nterruptons of any length are often accompaned by voltage fluctuatons whch may damage electronc equpment such as a securty system. After a power nterrupton has occurred, mmedately conduct a complete system test to ensure that the system operates as ntended. Falure of Replaceable Batteres Ths system s wreless transmtters have been desgned to provde several years of battery lfe under normal condtons. The expected battery lfe s a functon of the devce envronment, usage and type. Ambent condtons such as hgh humdty, hgh or low temperatures, or large temperature fluctuatons may reduce the expected battery lfe. Whle each transmttng devce has a low battery montor whch dentfes when the batteres need to be replaced, ths montor may fal to operate as expected. Regular testng and mantenance wll keep the system n good operatng condton. Compromse of Rado Frequency (Wreless) Devces Sgnals may not reach the recever under all crcumstances whch could nclude metal objects placed on or near the rado path or delberate jammng or other nadvertent rado sgnal nterference. System Users A user may not be able to operate a panc or emergency swtch possbly due to permanent or temporary physcal dsablty, nablty to reach the devce n tme, or unfamlarty wth the correct operaton. It s mportant that all system users be traned n the correct operaton of the alarm system and that they know how to respond when the system ndcates an alarm. Smoke Detectors Smoke detectors that are a part of ths system may not properly alert occupants of a fre for a number of reasons, some of whch follow. The smoke detectors may have been mproperly nstalled or postoned. Smoke may not be able to reach the smoke detectors, such as when the fre s n a chmney, walls or roofs, or on the other sde of closed doors. Smoke detectors may not detect smoke from fres on another level of the resdence or buldng. Every fre s dfferent n the amount of smoke produced and the rate of burnng. Smoke detectors cannot sense all types of fres equally well. Smoke detectors may not provde tmely warnng of fres caused by carelessness or safety hazards such as smokng n bed, volent explosons, escapng gas, mproper storage of flammable materals, overloaded electrcal crcuts, chldren playng wth matches or arson. Even f the smoke detector operates as ntended, there may be crcumstances when there s nsuffcent warnng to allow all occupants to escape n tme to avod njury or death. Moton Detectors Moton detectors can only detect moton wthn the desgnated areas as shown n ther respectve nstallaton nstructons. They cannot dscrmnate between ntruders and ntended occupants. Moton detectors do not provde volumetrc area protecton. They have multple beams of detecton and moton can only be detected n unobstructed areas covered by these beams. They cannot detect moton whch occurs behnd walls, celngs, floor, closed doors, glass parttons, glass doors or wndows. Any type of tamperng whether ntentonal or unntentonal such as maskng, pantng, or sprayng of any materal on the lenses, mrrors, wndows or any other part of the detecton system wll mpar ts proper operaton. Passve nfrared moton detectors operate by sensng changes n temperature. However ther effectveness can be reduced when the ambent temperature rses near or above body temperature or f there are ntentonal or unntentonal sources of heat n or near the detecton area. Some of these heat sources could be heaters, radators, stoves, barbeques, freplaces, sunlght, steam vents, lghtng and so on. Warnng Devces Warnng devces such as srens, bells, horns, or strobes may not warn people or waken someone sleepng f there s an ntervenng wall or door. If warnng devces are located on a dfferent level of the resdence or premse, then t s less lkely that the occupants wll be alerted or awakened. Audble warnng devces may be nterfered wth by other nose sources such as stereos, rados, televsons, ar condtoners or other applances, or passng traffc. Audble warnng devces, however loud, may not be heard by a hearng-mpared person. Telephone Lnes If telephone lnes are used to transmt alarms, they may be out of servce or busy for certan perods of tme. Also an ntruder may cut the telephone lne or defeat ts operaton by more sophstcated means whch may be dffcult to detect. Insuffcent Tme There may be crcumstances when the system wll operate as ntended, yet the occupants wll not be protected from the emergency due to ther nablty to respond to the warnngs n a tmely manner. If the system s montored, the response may not occur n tme to protect the occupants or ther belongngs. Component Falure Although every effort has been made to make ths system as relable as possble, the system may fal to functon as ntended due to the falure of a component. Inadequate Testng Most problems that would prevent an alarm system from operatng as ntended can be found by regular testng and mantenance. The complete system should be tested weekly and mmedately after a break-n, an attempted break-n, a fre, a storm, an earthquake, an accdent, or any knd of constructon actvty nsde or outsde the premses. The testng should nclude all sensng devces, keypads, consoles, alarm ndcatng devces and any other operatonal devces that are part of the system. Securty and Insurance Regardless of ts capabltes, an alarm system s not a substtute for property or lfe nsurance. An alarm system also s not a substtute for property owners, renters, or other occupants to act prudently to prevent or mnmze the harmful effects of an emergency stuaton. IMPORTANT - READ CAREFULLY: DSC Software purchased wth or wthout Products and Components s copyrghted and s purchased under the followng lcense terms: (f) Termnaton - Wthout prejudce to any other rghts, DSC may termnate ths EULA f You fal to comply wth the terms and condtons of ths EULA. In such event, You must destroy all copes of the SOFTWARE PRODUCT and all of ts component parts. (g) Trademarks - Ths EULA does not grant You any rghts n connecton wth any trademarks or servce marks of DSC or ts supplers. Ths End-User Lcense Agreement ( EULA ) s a legal agreement between You (the company, ndvdual or entty who acqured the Software and any related Hardware) and Dgtal Securty Controls, a dvson of Tyco Safety Products Canada Ltd. ( DSC ), the manufacturer of the ntegrated securty systems and the developer of the software and any related products or components ( HARDWARE ) whch You acqured. If the DSC software product ( SOFTWARE PRODUCT or SOFTWARE ) s ntended to be accompaned by HARDWARE, and s NOT accompaned by new HARDWARE, You may not use, copy or nstall the SOFTWARE PRODUCT. The SOFTWARE PRODUCT ncludes computer software, and may nclude assocated meda, prnted materals, and onlne or electronc documentaton. Any software provded along wth the SOFTWARE PRODUCT that s assocated wth a separate end-user lcense agreement s lcensed to You under the terms of that lcense agreement. By nstallng, copyng, downloadng, storng, accessng or otherwse usng the SOFTWARE PRODUCT, You agree uncondtonally to be bound by the terms of ths EULA, even f ths EULA s deemed to be a modfcaton of any prevous arrangement or contract. If You do not agree to the terms of ths EULA, DSC s unwllng to lcense the SOFTWARE PRODUCT to You, and You have no rght to use t. SOFTWARE PRODUCT LICENSE The SOFTWARE PRODUCT s protected by copyrght laws and nternatonal copyrght treates, as well as other ntellectual property laws and treates. The SOFTWARE PRODUCT s lcensed, not sold. 1.GRANT OF LICENSE Ths EULA grants You the followng rghts: (a) Software Installaton and Use - For each lcense You acqure, You may have only one copy of the SOFTWARE PRODUCT nstalled. (b) Storage/Network Use - The SOFTWARE PRODUCT may not be nstalled, accessed, dsplayed, run, shared or used concurrently on or from dfferent computers, ncludng a workstaton, termnal or other dgtal electronc devce ( Devce ). In other words, f You have several workstatons, You wll have to acqure a lcense for each workstaton where the SOFTWARE wll be used. (c) Backup Copy - You may make back-up copes of the SOFTWARE PRODUCT, but You may only have one copy per lcense nstalled at any gven tme. You may use the back-up copy solely for archval purposes. Except as expressly provded n ths EULA, You may not otherwse make copes of the SOFTWARE PRODUCT, ncludng the prnted materals accompanyng the SOFTWARE. 2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS (a) Lmtatons on Reverse Engneerng, Decomplaton and Dsassembly - You may not reverse engneer, decomple, or dsassemble the SOFTWARE PRODUCT, except and only to the extent that such actvty s expressly permtted by applcable law notwthstandng ths lmtaton. You may not make any changes or modfcatons to the Software, wthout the wrtten permsson of an offcer of DSC. You may not remove any propretary notces, marks or labels from the Software Product. You shall nsttute reasonable measures to ensure complance wth the terms and condtons of ths EULA. (b) Separaton of Components - The SOFTWARE PRODUCT s lcensed as a sngle product. Its component parts may not be separated for use on more than one HARDWARE unt. (c) Sngle INTEGRATED PRODUCT - If You acqured ths SOFTWARE wth HARDWARE, then the SOFTWARE PRODUCT s lcensed wth the HARDWARE as a sngle ntegrated product. In ths case, the SOFTWARE PRODUCT may only be used wth the HARDWARE as set forth n ths EULA. (d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make t avalable to others or post t on a server or web ste. (e) Software Product Transfer - You may transfer all of Your rghts under ths EULA only as part of a permanent sale or transfer of the HARDWARE, provded You retan no copes, You transfer all of the SOFTWARE PRODUCT (ncludng all component parts, the meda and prnted materals, any upgrades and ths EULA), and provded the recpent agrees to the terms of ths EULA. If the SOFTWARE PRODUCT s an upgrade, any transfer must also nclude all pror versons of the SOFTWARE PRODUCT. 3. COPYRIGHT - All ttle and ntellectual property rghts n and to the SOFTWARE PRODUCT (ncludng but not lmted to any mages, photographs, and text ncorporated nto the SOFTWARE PRODUCT), the accompanyng prnted materals, and any copes of the SOFTWARE PRODUCT, are owned by DSC or ts supplers. You may not copy the prnted materals accompanyng the SOFTWARE PRODUCT. All ttle and ntellectual property rghts n and to the content whch may be accessed through use of the SOFTWARE PRODUCT are the property of the respectve content owner and may be protected by applcable copyrght or other ntellectual property laws and treates. Ths EULA grants You no rghts to use such content. All rghts not expressly granted under ths EULA are reserved by DSC and ts supplers. 4. EXPORT RESTRICTIONS - You agree that You wll not export or re-export the SOFTWARE PRODUCT to any country, person, or entty subject to Canadan export restrctons. 5. CHOICE OF LAW - Ths Software Lcense Agreement s governed by the laws of the Provnce of Ontaro, Canada. 6. ARBITRATION - All dsputes arsng n connecton wth ths Agreement shall be determned by fnal and bndng arbtraton n accordance wth the Arbtraton Act, and the partes agree to be bound by the arbtrator s decson. The place of arbtraton shall be Toronto, Canada, and the language of the arbtraton shall be Englsh. 7. LIMITED WARRANTY (a) NO WARRANTY - DSC PROVIDES THE SOFTWARE AS IS WITHOUT WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE. (b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsble for problems caused by changes n the operatng characterstcs of the HARDWARE, or for problems n the nteracton of the SOFTWARE PRODUCT wth non-dsc-software or HARDWARE PRODUCTS. (c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU. (d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE PRODUCT. (e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY. WARNING: DSC recommends that the entre system be completely tested on a regular bass. However, despte frequent testng, and due to, but not lmted to, crmnal tamperng or electrcal dsrupton, t s possble for ths SOFTWARE PRODUCT to fal to perform as expected.

5 Table of Contents Chapter Descrpton Page 1. Introducton PC9155 Model Dfferences Specfcatons Controls & Indcators Data Entry Installaton Hardware Installaton Wrng Wreless Devce Enrollment Global Wreless Devce Placement Test Indvdual Wreless Devce Placement Test GPRS/Ethernet Intalzaton Operaton Operatng Modes Language Selecton [] Commands Functon Keys Programmng Template Programmng DLS Programmng Installer Programmng Installer Programmng Index to Programmng Optons Programmng Worksheets Programmng Descrptons Testng & Troubleshootng Wreless Devce Placement Test Testng the System Resettng the System to Factory aults Troubleshootng Battery Removal/Replacement Appendx A: Appendx B: Appendx C: Appendx D: Reportng Code Formats APP-1 Communcator Format Optons APP-5 2-Way Audo Verfcaton (PC5950) APP-6 Regulatory Approvals Informaton APP-6 v

6 PC9155 Wreless Alarm System 1 Introducton Ths manual provdes nstallaton and programmng nformaton for the PC9155 two-way wreless seres of alarm panels. The PC9155 s a twoway wreless alarm system that can nterface wth one-way and two-way RF devces. Three separate hardware platforms exst for the 433 MHz and 868 MHz versons. 1.1 PC9155 Model Dfferences Models wth a G n the suffx have a GS2065 module nstalled. The GS2065 module s a GSM (Global System for Moble communcatons) wreless cell communcator that communcates wth a GPRS (General Packet Rado Servces) global network that can be programmed as the prmary or backup communcator. Models wth a D n the suffx have a TL265GS module nstalled. The TL265GS module combnes the dual functonalty of the GS2065 wreless cell communcator and T-Lnk TCP/IP Ethernet/Internet communcator. Ether functon can be programmed as the prmary or backup communcator. All models can communcate va telephone (PSTN) n addton to cell and Internet descrbed above. Refer to the assocated nstallaton gude for programmng of the GS2065 and TL265GS modules. 1.2 Specfcatons Table 1-2 Specfcatons Specfcatons Temperature Range...0 C-49 C (32 F F) Humdty...93%RH Non Condensng Power Current Draw (panel) 240 VAC Prmary...57mA(AC)(Max) 120 VAC Prmary...114mA(AC)(Max) 16.5 VAC Secondary...855mA(AC)(Max) Current Draw (panel) Battery Only Standby...90mA Max Transmt (GPRS/Ethernet Module)...330mA Max Battery Capacty... 12VDC 2.3Ah Chargng Rate...240mA. (12Hrs Max) Backup Tme (No Aux)... 24Hr Aux+ Voltage VDC Current ma Max PGM 1&2 Output Current... 50mA (ea.) Note: Aux and PGM outputs share the 200mA load. Wreless Transcever Operatng Frequency Panel MHz/ MHZ Dmensons: PC H10.5 x W8.5 x D 2.3 n WT H4.9 x W6.5 x D 1.25 n wth wall bracket... H4.9 x W6.5 x D 1.5 n Weght PC9155 NA lb. (1.830Kg) PC9155 EU (Internal Transformer) lb. (2.275Kg) WT lb. (0.454Kg) Out of the Box: PC9155 RJ31-x Telephone (NA only) Transformer: NA external, EU nternal Mountng Hardware Kt Installaton, Keypad & User manuals...qty (1) ea. One-way, Two-way Devce Installaton sheets...as requred Table 1-1 PC9155 Models Note: For SIA CP-01 complant nstallatons the mnmum requred components are: PC Control Panel and WT Keypad. Optonal components that can be used wth the system are: TL265GS, GS2065, WT5500P-433, PT4, WT4989 and WT4901. Model PC PC PC9155G-433 PC9155G-868 PC9155D-433 PC9155D-868 Operatng Frequency MHz MHz MHz MHz MHz MHz GS2065 TL265GS Note: Only Models PC , PC9155D-433 and PC9155G-433 are UL/ULC lsted Table 1-3 Compatble Wreless Devces Compatble Wreless Devces WS, WLS, EV prefxes ndcate one-way wreless devce. WT prefx ndcates two-way wreless devce. Descrptons PC9155x-433 PC9155x-868 Wreless Keypads Proxmty Tag Door Contacts Moton Detectors Smoke Detector UL WT UL WT5500P-433 UL PT4 UL WS4945 UL WS4965 **WS4975 EV-DW4955 ***EV-DW4975 UL WS4904 UL WS4904P UL WLS UL WS4916 UL WS4926 WT WT5500P-868 PT8 WS8945 WS8965 WS8975 WS8904 WS8904P WS8916 CO (Carbon Monoxde) Detector WS4913 WS8913 Flood Detector WS4985 WS8985 Glass Break Detectors UL WLS912L-433 Shock Detector EV-DW4927 Wreless Srens Indoor Outdoor UL WT4901 UL WT4911 WT8901 WT8911 Wreless Keys UL WS4939 WS4949 WS4959 WS4969 WS4979 UL WT4989 WS8939 WT8989 Panc Pendants UL WS4938 WS8938 UL WS4938-2W Hold-up WLS Only UL approved devces are to be used wth lsted systems. **Not avalable n North Amerca, South Amerca and New Zealand ***Avalable n North Amerca, South Amerca and New Zealand only 1-1

7 1 Introducton 1.3 Controls & Indcators The PC9155 can have a maxmum of eght status ndcators located on the front panel. The four ndcators located on the left sde of the panel ndcate the Ready status, Armed status, Trouble status and AC Power status of the alarm system. The four ndcators are located on the rght sde of the panel only f a GS2065 or TL265GS module s nstalled. These ndcate Communcator Trouble status, Network status (TL265GS only), and Hgh or Low sgnal strength. Table 1-4 Controls & Indcators - Alarm Panel Alarm Indcators GPRS/Ethernet Module Indcators Ready: Panel s ready to be armed. Armed: Panel s armed. Trouble: Enter [][2] to vew troubles. Yellow ndcates trouble. Orange ndcates RF Jam trouble. AC Power: On=AC present. OFF=AC absent Communcator Trouble: Enter [][2] to vew troubles. Network: Internet communcaton absent. Sgnal Strength (Hgh): GPRS sgnal strength s hgh. Sgnal Strength: (Low): GPRS sgnal strength s low. Fgure 1-1 Controls & Indcators - Keypad Ambent Lght Sensor LCD < > ndcates user can scroll through optons System s Ready to Arm <> LED Indcators Ready Armed Trouble AC Power Scroll Keys Emergency Keys Fre Auxlary Functon Keys Panc * 0 # DG Data Entry Conventons Used Brackets [ ] ndcate numbers or symbols that are to be entered on the keypad. E.g., [][8][Installer Code][898] requres the followng key enteres: ndcates to the alarm system that a specal command wll be entered. places the alarm system n Installer Programmng mode. s the default nstaller code. The default nstaller code should be changed when programmng the system. ndcates the partcular programmng secton beng accessed. E.g. [898] Wreless Devce Enrollment [899] Template Programmng [999] Alarm System ault 1-2

8 PC9155 Wreless Alarm System Enterng Letters Some commands requre the entry of letters (.e., A, B, C, D, E, F). To enter a letter, press and the number on the keypad that corresponds to the approprate letter, as ndcated below. 1 = A 4 = D 2 = B 5 = E 3 = C 6 = F The cursor wll blnk to ndcate that you are enterng letters. To revert back to numerc entry press. Incorrect Data Entres: To change a data entry before t has been accepted by the alarm system, use the scroll keys to reposton the cursor then re-enter the dgt. If the data has already been accepted by the system, press [#] to ext the secton then re-enter the programmng secton and enter the data agan. If you ncorrectly enter 0001 n Step 2 of Program alarm system n Template Programmng, you must ether reset the alarm system to ts default values (secton. [996], re-enroll all wreless devces and re-program the system) or re-enter the correct data n Installer Programmng [][8]. Specal Keys: Scroll symbols < > on the dsplay ndcate that there are optons you can vew by pressng the keys. These scroll keys can also be used to poston the cursor. The key s smlar n functon to the ENTER key on a personal computer. It s generally used to accept the exstng programmng opton. It s also the frst key entry for [] commands and can be used to enter the letters A-F when n Installer Programmng mode. The key functons smlarly to the ESCAPE key on a personal computer. It s generally used to ext the current programmng secton or to return to the prevous menu. 1-3

9 2 Installaton 2 Installaton 2.1 Hardware Installaton Hardware Installaton Step 1 Step 2 Step 3 Step 4 Select a sutable locaton for the alarm panel n a dry locaton, close to an unswtched AC outlet, phone lne (f requred), and Ethernet cable (f requred). DO NOT mount system on an electrcal box. Poston system away from metal objects (e.g., applances, furnace, duct work etc.). Gently pry the front cover from the chasss usng a small slotted screwdrver n the slots provded. Remove the battery by depressng the plastc battery retaner on the rght sde of the battery wth thumb to free the battery from the housng. Cauton: Before nstallaton or operaton, remove and dspose of the plastc bag coverng the battery. If requred, connect the battery cable to the battery connector on the PC board. Remove the termnal protecton from the battery. Install the battery cable on the battery spade lug termnals [(+)Red, (-)Black). To nstall, slde the left sde of the battery [(+) termnal] under the left battery retanng bracket. Insert a slot screwdrver between the battery and rght retanng bracket. Lever the rght retanng bracket to the rght whle pressng the battery frmly n place. Route wrng through the channels provded to the wrng access hole. See Fgure 2-3. Secure unt to wall usng the mountng holes provded. For PC9155 models equpped wth an nternal transformer, route AC wrng through the AC wrng gude then through the access hole adjacent to the nternal transformer. Secure the AC lne and neutral (N) wrng to the fused sde of the termnal block as ndcated. For PC9155D models, route the RJ-45 termnated CAT5 Ethernet cable through the wrng gude then through the wrng access hole and connect to the RJ-45 jack located on the TL265GS module. Ethernet communcaton lnes must be connected to an approved (acceptable to local authortes) type NID (Network Interface Devce) before leavng the premses (e.g., UL Installatons, UL60950 lsted NID). If requred remove/replace exstng coaxal cable and connect TL265GS/GS2065 to an external antenna. Fgure 2-2 GPRS/Ethernet Module Wrng Detals 250VAC/ 160mA FUSE Fgure 2-1 AC Fuse Block SIM Card Jumperng Ethernet Cable to ground may cause communcaton problems. Use wth cauton To Alternate External Antenna Connecton To Router/Ethernet GND SHLD Insert small flat head screwdrver between cable and Rx/Tx module then gently pry plug loose. T-1 R-1 TIP RING IO2 IO1 -AUX AUX+ AC AC BATTERY CONNECTION (NOT SHOWN) 2-1

10 PC9155 Wreless Alarm System Fgure 2-3 Mountng & Wrng Detals Internal Transformer Verson Only FUSE Internal Transformer Verson Only DG AC T-1 R-1 TIP RING I/O2 I/O1 - AUX + AC AC CAUTION: The Ethernet communcaton lnes must be connected frst to an Approved (acceptable to the local authortes) type NID (Network Interface Devce) before leavng the premses (e.g., UL nstallatons, UL60950 Lsted NID). Phone Lne T1-Brn Connects to n-house phone lne R1- Gra Connects to n-house phone lne Tp - Grn Connects to outsde phone Lne. Allows system to seze the phone lne from devces connected to T1-R1 PC9155 Telephone I/O T-1 R-1 Tp Rng 2 1 Aux AC Rng - Red Connects to outsde phone Lne. Allows system to seze the phone lne from devces connected to T1-R1 I/O I/O - 1 Can be confgured as a PGM output (50mA) or hard wred zone nput (Zone 33) I/O - 2 Can be confgured as a PGM output (50mA) or hard wred zone nput (Zone 34) Aux Aux - Provdes common connecton for hard-wred zones and Aux+ power Aux + Provdes +12VDC, 200mA (Max.) for PGMs and modules AC ~ Connects drectly to external 16.5VAC transformer or fused nternal transformer ~ Connects drectly to external 16.5VAC transformer or fused nternal transformer 2-2

11 2 Installaton 2.2 Wrng 1. I/O Wrng The two I/O termnals can be programmed as hard-wred zone nputs and/or PGM outputs. See programmng secton [013] Opt [1,2]. 1a. Zone Wrng Zones 1-32 are reserved for wreless zones. If programmed as zone nputs, I/O- 1 s zone 33 and I/O-2 s zone 34. Zones can be wred for Normally Open (NO) contacts wth sngle-end-of-lne resstors or Normally Closed (NC) contacts wth sngle-end-of-lne or doubleend-of-lne resstors. Observe the followng gudelnes. For UL/ULC lsted nstallatons use SEOL or DEOL only Use mnmm 22AWG, maxmum 18 AWG wre DO NOT use shelded wre Wre run resstance shall not exceed 100 Ω Burglary Zone Wrng Chart Wre Sze Max wre length to end-of-lne resstor AWG mm Feet Meters Fgures are based on maxmum wrng resstance of 100 Ω Zones 33 and 34 are defaulted for SEOL resstors Programmng secton [133]-[134] opt.[14] selects Normally Closed or Normally Open Programmng secton [133-[134] opt.[15] selects SEOL resstors Programmng secton [133]-[134] opt.[16] selects DEOL resstors Zone Status - Loop Resstance/Loop Status (DEOL only) Fault - 0Ω (shorted wre/loop)(shorted wre to 4.5KOhm) Secure - 5,600Ω (contact closed)(4.5kohm to 6.25KOhm) Volated - 11,200Ω (contact open)(13.5kohm to open) Tamper - nfnte (broken wre, open)(9kohm to 13.5KOhm) Normally Closed Loops - Do NOT use for UL Installatons Any I/O Termnal ALARM CONTACT AUX- Termnal 2 NORMALLY CLOSED CONTACTS WITH NO END OF LINE RESISTOR Sngle End-of-Lne Resstor Wrng Any I/O Termnal Any I/O Termnal AUX- Termnal 1 NORMALLY CLOSED CONTACT WITH 5600Ω END OF LINE RESISTOR AUX- Termnal 1 NORMALLY OPEN CONTACT AND 1 NORMALLY CLOSED CONTACT WITH 5600Ω END OF LINE RESISTOR Any I/O Termnal Double End-of-Lne Resstor Wrng Any I/O Termnal AUX- Termnal 2 NORMALLY OPEN CONTACTS AND 2 NORMALLY CLOSED CONTACTS WITH 5600Ω END OF LINE RESISTOR AUX- Termnal DEOL CIRCUIT ALARM 1 NORMALLY CONTACT CLOSED CONTACT WITH 5600Ω END OF LINE RESISTORS Any I/O Termnal Any I/O Termnal Any I/O Termnal AUX- Termnal AUX- Termnal 1 NORMALLY CLOSED CONTACT WITH NO END OF LINE RESISTOR 1 NORMALLY OPEN CONTACT WITH 5600 Ω END OF LINE RESITSTOR AUX- Termnal TEMPER CONTACT DEOL CIRCUITS 2 NORMALLY CLOSED CONTACTS WITH 5600Ω END OF LINE & TAMPER RESISTOR 1b. Programmable Output (PGM) and Aux Wrng I/O termnals confgured as Programmable Outputs (PGMs) swtch to ground when actvated by the alarm system. The PGMs are open collector outputs. Wth a 45 ma load, the voltage measured at the PGM and Aux + shall be approxmately 8V wth respect to ground. Wth a 25 ma load, the voltage measured shall be approxmately 10V. Connect the postve sde of the devce to the Aux+ termnal. Connect the negatve sde of the devce to the I/O termnal. Each PGM can provde 50mA maxmum output. NOTE: The alarm system can provde 200mA maxmum of AUX current for PGMs, relays, LEDs etc. The AUX output shall be used only for resdental burglary applcatons. I/O I/O LED output wth: Current lmtng resstor and optonal relay drver output. Compatble ntatng devces ntended to be used on the AUX output shall be rated for the range: 9.6VDC to 13.8VDC mn. 2-3

12 PC9155 Wreless Alarm System 1c. PC Way Audo Verfcaton Module Wrng Install the PC5950 n a metal cabnet secured to a wall. Power down the PC9155 f requred. Route wrng to the PC9155 through the wrng gude. Route wrng to the audo statons as ndcated (2 Max). Ensure telephone lne wrng enables the PC9155 to seze the lne. Test System. Refer to the PC5950 Installaton Gude. Refer to Appendx D: 2-Way Audo Verfcaton (PC5950). Wrng dagram 1, Talk/Lsten wth Sren Shutdown, does a full talk/lsten n sesson for slent alarms. If a lsten n only sesson s requred for slent alarms, use wrng dagram 2, Lsten-n Only wth Sren Shutdown. PC5950 Programmng Secton 01 - Set to 1 (Hard Trp) Secton 10 - Set to 2 (Trgger Enable:Auto Trp by Bell or Green) PC5950 Programmng Secton 01 - Set to 1 (Hard Trp) Secton 07 - Set to 1 (Trgger Hgh) Secton 10 - Set to 2 (Trgger Enable: Auto Trp by Bell or Green) 2. Telephone Lne Wrng Wre the ncomng lne (phone company) and outgong lne (premses) to the connecton termnals of an RJ31x connector as ndcated. Ths wll allow lne sezure f requred by the alarm system. Use 24AWG mnmum for wrng. Communcaton formats are programmed n secton [350]. Telephone call drectons are programmed n sectons [351]-[376]. Program I/O 1 - Audo Verfcaton PGM Program I/O 2 - Audo Verfcaton Montor Zone T-1 R-1 TIP RING BRN GRA GRN RED RJ-31X 3. Battery 4. AC Wrng Sealed Lead Acd Battery Model FP VDC 2.3Ah@20Hr. dscharge rate Standby...24Hr Battery Replacement Removal: (1) Dsconnect the RED (+) and BLACK (-) connectors from the battery. (2) Depress the plastc battery retaner on the rght sde of the battery wth thumb to free battery from the housng, then remove battery. Replacement: (1) Remove termnal protecton from battery. (2) Install battery cable on battery spade lug termnals. (3) Slde left sde of battery [(+) termnal] under the left battery retanng bracket. (4) Insert a slot screwdrver between the battery and rght retanng bracket. Lever the rght retanng bracket to the rght whle pressng the battery frmly n place. (5) If requred route battery cable through wre gudes and connect to the battery connector. DSC recommends battery replacement every 3-5 years. Dspose of battery n accordance wth local regulatons. AC Transformer Requrements: Prmary: 120VAC, 60Hz., 0.200A (For UL/ULC Lsted nstallatons) 240VAC, 50Hz., 0.100A (Fuse: 503 S, 250V/160mA Fast-Blo) Secondary: 16.5VAC/20VA The followng plug-n transformers shall be used: North Amerca (UL Lsted Installatons) PTD1620U-CC Canada (ULC Lsted Installatons) PTD1620 Internal Transformer Secondary Wre Run Dstance AWG Feet Meters Do NOT connect transformer to a receptacle controlled by a swtch. Use a Class 2, power lmted transformer for UL/ULC nstallatons. 2.3 Wreless Devce Enrollment Installng a one-way or two-way wreless devce requres programmng the system wth the Electronc Seral Number (ESN) so that t can be dentfed when an event s communcated. Two-way devces must also ntate communcaton wth the control panel to complete the enrollment process. The control panel wll then assgn the devce a unque system ID, devce ID and encrypton key. Ths nformaton s sent to the devce and s stored n ts memory. The system uses these ID's and encrypton to communcate events. Methods of Enrollment Two methods of enrollment are avalable: Quck Enroll Used to enroll new devces on the system. (See below for procedure). The Quck Enroll procedure performs twoway enrolment communcatons n the background. The Two-way devce and One-way devce enrollment procedures are dentcal. Manual or DLS Enroll See Installer Programmng or DLS Programmng (secton [804]). Manual or DLS enrollment of two-way wreless keys requres the devce to be physcally trggered to complete the enrollment

13 2 Installaton Enroll wreless devces n the followng sequence: Keypad Srens Sensors Pendants Wreless Keys Refer to the assocated nstallaton sheet for addtonal detals on how to actvate specfc wreless devces. Enrollng Wreless Keypads When the PC9155 s frst powered up a 2 mnute wndow s establshed for enrollng the frst keypad. The AC Power and Ready LEDs wll flash for the duraton of the enrollment wndow. The keypad must be powered up and enrolled wthn ths perod. If the keypad s not enrolled durng ths wndow (.e., The AC Power and Ready LEDs stop flashng) the panel must be powered down then powered up agan to re-open the 2 mnute enrollment wndow. Step 1 Step 2 Power up alarm system. Connect alarm system to AC Power. The Ready and AC LEDs flash for 2 mnutes. Power up keypad. Connect keypad to AC power or nstall new batteres. After a few seconds the keypad may beep rapdly. Hold [1] and [] to Enroll Keypad s dsplayed. Press the and keys smultaneously to enroll the keypad. WFKP Enrollment Successful s dsplayed. Hold [1] and [*] to Enroll Keypad WFKP Enrollment Successful If the Faled to Enroll message s dsplayed perform the followng: Retry the enrollment. Reposton the keypad closer to the control panel. Verfy that the READY and POWER LED ndcators are flashng on the panel. If not, dsconnect the panel from AC and DC power sources then reconnect. Check for RF nterference. Verfy that the keypad s the correct model for the PC9155 System. Step 1 Step 2 Step 3 Enter [][8][5555][898] The followng s dsplayed: Enrollng Addtonal Keypads, Srens & Wreless Keys Actvate the devce as ndcated below or n the devce s Installaton Sheet. Addtonal keypad: press the and keys smultaneously. Sren: power up the devce, press the tamper button or the test button to enroll. Wreless key: Press any Key to actvate. To re-enroll on another system, press and hold the and buttons smultaneously for 3 seconds. The Electronc Seral Number (ESN) s dsplayed on the frst keypad. Press to confrm the ESN. If the ESN s ncorrect press then repeat ths step. After successful confrmaton of the ESN, the system prompts for the slot number. The next avalable slot s dsplayed. Press to accept or enter for keypads and srens or for wreless keys. To re-enroll a wreless key press smultaneously for approxmately 3 seconds. Wreless Enrollment Mode 8F0125 Confrm ESN? * Press (*) or Zone #: 02 Press (*) for Zone Type:

14 PC9155 Wreless Alarm System Step 1 Enter [*][8][5555][898] Wreless Enrollment Mode s dsplayed. Enrollng Sensors & Pendants Wreless Enrollment Mode Step 2 Place the Wreless devce near the alarm system. Actvate the devce as descrbed n the assocated nstallaton sheet. The Electronc Seral Number (ESN) s dsplayed. Press to confrm seral number. 223E02 Confrm ESN? * The ESN s a 6-dgt alphanumerc number located on a removable stcker on the wreless devce. If the seral number s ncorrect, press and repeat ths step. Step 3 After successful confrmaton of the seral number, the system prompts for the zone #. The next avalable zone s dsplayed. Press to accept the selecton or enter a zone number (01 to 32). For the frst enrolled devce enter. If a second devce s enrolled n a zone that already has a devce enrolled, the system offers the choce of overwrtng the exstng devce. Press to overwrte the zone. Press to re-enter the zone number (prevous dsplay). Enter Zone # 00 Zone 01: 224A01 Overwrte? * Step 4 Step 5 After successful entry of the zone number, the system prompts for the zone type. (The recommended zone type s dsplayed). Press to accept the zone type or: Enter for: Delay Type 1 - Entry/Ext Pont e.g., door. Enter for: Instant Type - e.g., wndow. Enter for: Interor Stay/Away Type - e.g., moton detector. Enter for: Delayed 24 Hr. Fre Type - e.g., smoke detector. Enter for: 24 Hr. Panc - e.g., panc pendant. After successful entry of the zone type: The alarm system returns to the Wreless Enrollment screen. Contnue wth one of the followng: Actvate another sensor or pendant to contnue enrollment (Step 2). Press to enter another programmng secton. Press to ext Installer Programmng. Enrollng Proxmty Tags Press (*) or Zone Type: 03 Wreless Enrollment Mode If ths functon s avalable on the keypad, the [][5] menu provdes the opton to assgn a proxmty tag to an access code once the access code has been entered. Swpe the tag to enroll t durng user access code assgnment. To unenroll a proxmty tag, the user code must be deleted. To retan the user code t must be reentered. 2-6

15 2 Installaton 2.4 Global Wreless Devce Placement Test Wreless Devce Placement Perform the Wreless Devce Placement testng on keypads, sounders and sensors only. Ths test s NOT requred for wreless keys or pendants. Verfy that pendants and Key FOBs operate wthn the desred operatng area by armng and dsarmng the sytem. Test each devce multple tmes to ensure a good placement. If a devce tests BAD reposton the devce and retest. Slght changes n placement can cause sgnfcant dfferences n sgnal strength and range of the wreless devce. Step 1 To enter ndvdual Wreless Devce Placement Test: Press - for wreless zones - for wreless keypads - for wreless srens represents the new nstaller code programmed n Installer s programmng to replace the 5555 default nstaller code. Enter Secton --- Select Devce <> for Test Step 2 Place the wreless devce n the ndended mountng locaton. Actvate the devce as descrbed n the assocated nstallaton sheet. If the alarm system receves a STRONG sgnal the bell wll sound once and Locaton s Good wll be dsplayed on the LCD. If the alarm system receves a WEAK sgnal the bell wll sound 3 tmes and Locaton s Bad wll be dsplayed on the LCD. If the alarm system ndcates no response, reposton wreless devce and repeat test. Actvate Devce Locaton s Good Actvate Devce Locaton s Bad Step 3 Repeat Step 2 for each devce. When placement testng s complete, press to ext Installer Programmng. System s Ready to Arm <> Two-way wreless keys must be actvated by pressng any key before they become functonal. To placement test a wreless keypad, press number keys 0-9. To placement test a wreless sren, press the Test button, or tamper the devce. 2.5 Indvdual Wreless Devce Placement Test Wreless Devce Placement Placement testng can be performed on ndvdual wreless devces. To confgure the alarm system for ndvdual placement test, opton [8] n secton [804][900] must be turned off. Use the scroll keys or enter a 2 dgt entry to select a specfc keypad, zone or sren dependng on whch placement test secton s entered. Step 1 To enter ndvdual Wreless Devce Placement Test: Press - for wreless zones - for wreless keypads - for wreless srens represents the new nstaller code programmed n Installer s programmng to replace the 5555 default nstaller code. Enter Secton --- Select Devce <> for Test 2-7

16 PC9155 Wreless Alarm System Step 2 Step 3 Step 4 Enter a 2 dgt zone number, keypad number, or sren number dependng on the placement test secton entered, or scroll to the desred devce and press to begn ndvdual placement test. Place the wreless devce n the ntended mountng locaton. Actvate the devce as descrbed n the assocated nstallaton sheet. If the alarm system receves a STRONG sgnal the bell wll sound once and Locaton s Good wll be dsplayed on the LCD. If the alarm system receves a WEAK sgnal the bell wll sound 3 tmes and Locaton s Bad wll be dsplayed on the LCD. If the alarm system ndcates no response, reposton wreless devce and repeat test. Repeat Step 3 for each devce. Once the placement test s complete for the devce, press [#] once and select the next smlar devce. When placement testng s complete, press to ext Installer Programmng. Actvate Devce Locaton s Good Actvate Devce Locaton s Bad System s Ready to Arm <> 2.6 GPRS/Ethernet Module Setup/Intalzaton Perform the followng after system nstallaton and programmng: Ensure that the followng sectons are programmed: Central Staton Phone Number,(Template Programmng - Entry 5) (f applcable, n sectons [301]-[303] & [305]) Account code, secton [310], (Template Programmng - Entry 6) Communcatons Format, Secton [350]- set to [04] SIA FSK GPRS/Ethernet Module Enable secton [382] Opton[5] - set to GPRS/Ethernet Module Enabled 2-8

17 3 Operaton 3 Operaton 3.1 Operatng Modes Away Armng Away Armng arms the entre system ncludng the permeter and nteror devces. The Ready lght must be ON to arm the system. If the Ready lght s OFF, ensure all protected doors and wndows are secure or bypassed. To arm the system n the Away mode, ether press and hold the Away functon key for 2 seconds or enter a vald user code and leave the premses through a door programmed as Delay. Upon pressng a functon key or enterng an access code, the Armed lght wll turn ON. If the Audble Ext Delay opton s enabled, the keypad wll beep once every second durng the ext delay (and three tmes a second durng the last 10 seconds) to alert the user to leave. The Ready lght wll turn off when the Ext Delay ends Stay Armng Stay Armng s ntended to arm the permeter of the premses whle permttng movement wthn the premses. The Ready lght must be ON to arm the system. If the Ready lght s OFF ensure all protected doors and wndows are secure or bypassed. To arm the system n the Stay mode, ether press and hold the Stay functon key for 2 seconds or enter a vald user code and stay wthn the premses (do NOT volate a door programmed as Delay). Upon pressng a functon key or enterng an access code, the Armed lght turns ON. If the Stay functon button s used, the keypad wll not beep durng the ext delay and the user can stll ext the buldng wthout the system revertng to Away mode. When a user code s used, the keypad beeps f the Audble Ext Delay opton s enabled. The Ready lght turns off when the ext delay ends Nght Armng Nght armng s ntended to arm the permeter and restrct movement to desgnated areas n the nteror (e.g., hallways from bedrooms to bathrooms). If nght zones are programmed, enterng [][1] whle the system s armed n stay mode wll re-actvate all nteror zones except those programmed as nght zones. Alternatvely, whle the system s dsarmed the Nght Arm functon key can be pressed for 2 seconds to arm the panel n nght mode. The Ready lght must be ON (dsarmed) or the system must be armed n the Stay mode to arm the system n ths mode. In Nght mode only nght zones (Zone defnton 37) are bypassed. When actvated, there are no acknowledgement beeps, the ext delay s slent and the panel logs Armed n Nght Mode. If there are no nght zone types programmed on the system, the system arms n Away mode and the panel logs Armed n Away Mode Dsarmng Zones must be programmed wth zone defntons (05 Interor Stay/Away, 06 Delay Stay/Away, or 32 Instant Stay/ Away) for ths functon to work. The user must enter through a door programmed as Delay. Upon enterng, the keypad emts a steady entry delay tone (and a pulsng tone durng the last 10 seconds of entry delay) to alert the user to dsarm the system. To dsarm the system, enter a vald user code, present a proxmty tag or use a wreless key. If an alarm occurred whle the panel was armed, the keypad dsplays Alarm n Memory and the zone(s) that went nto alarm durng the armed perod. Press the [#] key to return the keypad to the Ready state. 3.2 Language Selecton The keypad can be programmed to dsplay messages and labels n dfferent languages. Perform the followng when n Ready to Arm mode or at the Installer Programmng menu: [1] Press and hold both scroll keys [< >] smultaneously untl language optons are dsplayed. [2] Scroll to the desred language usng the scroll keys [< >]. [3] Press [] to select the desred language. 3.3 [ ] Commands The followng s a lst of the [] commands avalable and a descrpton of each: [][1] Bypass (dsarmed state)/reactvate Stay/Away Zones (armed state) [][2] Dsplay Trouble Condtons [][3] Dsplay Alarm Memory [[4] Door Chme Enable/Dsable [][5][Master/Supervsory Code] User Code Programmng [][6][Master/Supervsory Code] User Functons [][7][1/2] Command Outputs 1 and 2 [][8][Installer Code] Installer Programmng [][9][User Code] No-Entry Armng [][0] Quck Arm (dsarmed state)/quck Ext (armed state) 3-1

18 PC9155 Wreless Alarm System [][1] Bypass/Re-actvate Stay/Away and Nght Zones Press [][1] to enter Bypass mode. If the Code Requred for Bypass opton s enabled, enter a vald user code. The keypad dsplays Scroll to Bypass Zones. The keypad dsplays the programmed zone labels and ncludes the letter O n the bottom, rght corner f the zone s volated or the letter B f the zone s bypassed. Scroll to the approprate zone and press the [] key to change the bypass status (or enter the 2-dgt zone number). Once the correct zones are bypassed, press [#] to ext. Addtonal Bypass Commands Bypass Recall: In Bypass mode, press [99]. The keypad recalls the last group of zones that were bypassed. Clear Bypass: Press [00]. The keypad clears the bypass on all zones. Save Bypass: Press [95]. The keypad saves zones whch are manually bypassed. Recall Save: Press [91]. The keypad recalls the bypassed zones that were saved. Re-actvate Stay/Away and Nght Zones: Press [][1] when the system s armed n the Stay mode to change the armed status to Away mode or Nght mode. The system wll add the Stay/ Away zones back nto the system after the ext delay tme expres. If any zones are programmed as nght zones (zone defnton 37) pressng [][1] when the system s n Stay mode actvates Nght mode nstead of Away mode. Only nght zones are bypassed. The stay and away zones are added back nto the system. [][2] Trouble Dsplay Refer to Chapter 6: Testng & Troubleshootng, for troubleshootng assstance and a detaled descrpton of all trouble condtons. [][3] Alarm Memory Dsplay Pressng the scroll <> keys dsplay an Alarms n Memory message f an alarm occurred durng the last armed perod. Pressng [][3] dsplays the message Scroll to vew Alarms. To clear the memory, arm then dsarm the system. [][4] Door Chme Enable/Dsable Press [][4]. The keypad emts 3 rapd beeps to ndcate that the door chme feature s enabled or a steady 2-second tone f dsabled. The same functon can be performed by pressng and holdng the Chme functon key for 2 seconds. [][5] Program User Codes The followng table dentfes avalable user codes: Code Type Functon [01] [16] [40] General User Codes Master Code Determned by attrbutes programmed below All attrbutes descrbed below Programmng User Codes Press [][5] followed by the master code. The keypad dsplays the frst user (user 01) and ncludes the letter P f the user code s programmed. Scroll to the approprate user and press the [] key to program the user (or enter the 2-dgt user number). Enter a new 4 or 6-dgt user code or press [] to delete the user code. After the user code s programmed or deleted, scroll to another user or press [#] to ext. Proxmty tags can be assgned to a programmed user code on WT5500P keypads. After assgnng a user code, the dsplay prompts for the tag to be swpped. Ths assgns a proxmty tag to the user code. The user code wll have a T n the lower rght hand corner ndcatng that a tag s assocated wth that code. To delete a proxmty tag, the user code must be deleted. Refer to the Proxmty Tag Installaton Sheet for detals. The proxmty tag can be used n place of the access code for any of the nstructons referred to n the Operaton secton of ths manual. Programmng User Attrbutes Press [][5] followed by the master code or supervsor code. Press [9] followed by the 2-dgt user number to vew user attrbutes. To change user attrbutes, press the number correspondng to the attrbute or scroll to the desred attrbute and press []. When the correct attrbutes are assgned to the user, press [#] to ext. To change the attrbutes for another user, press [9] followed by the 2-dgt user number. When fnshed, press [#] to ext. These attrbutes affect the operaton of wreless keys. Wreless key numbers (01-16) correspond wth user access codes (01-16). Duress codes are not vald when enterng [*][5], [*][6] or [*][8] sectons. Duplcate codes and codes that are +/- 1 of an exstng code can not be programmed. 3-2

19 3 Operaton [1] Supervsor s Code: Ths attrbute s used for valdaton when enterng the [][5] User Code Programmng secton and [][6] User Functons secton. Note, the supervsor s code can only valdate programmng for codes wth equal or lesser attrbutes. The supervsor s code also allows ths user to create bypass groups f an access code s requred to enter nto [][1] Bypassng. [2] Duress Code: Duress codes are standard user codes that transmt the Duress Alarm Reportng Code whenever the code s entered to perform any functon on the system. [3] Bypass Zones: The user can manually bypass zones f bypassng requres an access code. [4-6] Future Use [7] Bell Squawk On Armng/Dsarmng: The panel squawks the bell when the user arms usng the away functon key and a user code, or f the away functon key s pressed on an dentfed wreless key. [8] One-tme Use Code: The one-tme-use code allows unlmted armng but only permts a sngle dsarmng once a day. The Dsarm functon s restored at mdnght. [][6] User Functons To access the User Functons secton, press [][6] followed by the master or supervsor code. Select one of the functons descrbed below by pressng the correspondng number or scrollng to the desred opton then pressng []. [1] Program Tme and Date: Enter the tme and date usng the followng format [HH:MM] [MM/DD/YY]. Program the tme usng mltary standard (e.g., 8:00 pm = 20:00 hours). [2]-[3] Future Use [4] System Test: The system actvates the sren output on medum volume for 2 seconds followed by full volume alarm for 2 seconds. All dsplay lghts and LCD pxels turn on. [5] Enable DLS: The panel wll temporarly enable DLS double-call for 6 hours. [6] User Intated DLS: The panel attempts to call the DLS computer. [7] Future Use [8] User Walk Test Mode: Walk Test mode allows the operaton of each detector n the system to be tested. Press [*][6][Master Code][8] to ntate Walk Test mode. Whle n Walk Test mode, the Ready, Armed, and Trouble LED's flash to ndcate that the walk test s actve. Re-enterng [*][6][Master Code][8] exts Walk Test mode. The system wll also automatcally termnate the Walk Test on completon; t wll sound an audble warnng (5 beeps every 10 seconds), begnnng 5 mnutes before the termnaton of the test. [9] Late to Open Control: Ths feature notfes a user f ther alarm system s not dsarmed by a programmed tme of day (see Late to Open Tme of Day). It s typcally used to track chldren after school. For example, f the parents get home from work at 5pm, and a chld gets home at 4pm, the programmable tmer could be set for 4:15. If the system s not dsarmed at ths tme an alert s sent to the montorng staton. The keypad dsplays "Late to Open s Enabled" and sounds a beep f [9] s pressed wthn the User Functons menu when ths feature s off. The LCD keypad dsplays "Late to Open s Dsabled" and sounds an error tone f [9] s pressed wthn the User Functons menu when ths feature s on. [0] Late to Open Tme of Day: Ths attrbute sets the tme for Late to Open Control programmed for attrbute [9] operaton. Vald entres for these sectons are 00:00-23:59. Enterng 99:99 dsables the late to open feature for that day. After the [0] key s pressed n the [][6] menu, acknowledge beeps are sounded and the message Press (*) for <> Sunday s dsplayed on the keypad. Pressng the [>] key scrolls through each day of the week from Sunday to Saturday. Whle n the Late to Open menu, enterng keys 1-7 also selects each day from Sunday to Saturday. Addtonal Keypad Functons The followng addtonal keypad functons are avalable: Event Buffer: Used to vew the 500-event panel buffer Brghtness Control: Used to adjust the dsplay backlghtng level for optmal vewng Contrast Control: Used to adjust the dsplay contrast level for optmal vewng Buzzer Control: Used to adjust the keypad buzzer tone for optmal sound 3-3

20 PC9155 Wreless Alarm System [][7][1 or 2] Command Outputs (1&2) Press [][7] then [1] or [2]. If the Command Output Code Requred opton s enabled, enter a vald user code. The panel actvates a command output assgned to any PGM. [][8] Installer Programmng Press [][8][Installer Code] to enter Installer Programmng. Installer programmng allows the nstaller to program all system functons. Refer to the secton 5: Installer Programmng for detals. [][9][User Code] No-Entry Armng Press [][9] followed by a vald user code. The system arms n the Stay mode after the ext delay expres and removes entry delay. All zones programmed as Delay functon lke Instant zones. The system flashes the Armed lght to ndcate that t s armed wth no entry delay. [][0] Quck Arm/Quck Ext Quck Arm: When dsarmed, press [][0] to arm the system. Quck Arm s equvalent to enterng your user code. Quck Ext: When armed, press [][0] to actvate Quck Ext. Quck Ext allows you to ext the premses wthout dsarmng the system.the system allows a sngle zone programmed as Delay to be volated and restored once durng the followng 2 mnute tme perod wthout changng the status of the system. 3.4 Functon Keys The keypad has 5 programmable one-touch functon keys located n a column down the rght-sde of the keypad. These keys can also be actvated by pressng and holdng number [1] through [5] respectvely for 2 seconds. The default for these keys are as follows: [1] Stay Arm [4] Bypass [2] Away Arm [5] Quck Ext [3] Chme Enable/Dsable 3-4