Advanced Systems Tester 900AST Series Calibration Verification Procedure
|
|
- Kristian Kelley
- 7 years ago
- Views:
Transcription
1 Advanced Systems Tester 900AST Series Calibratin Verificatin Prcedure Instructins March 2006
2 Table f Cntents Intrductin...3 Test Instruments Required...3 Test Cmpnents Required...3 Test Prcedure...3 Self-Calibratin...3 DC Vlts...3 AC Vlts...4 Ohms...4 Capitance...5 ID Tne...5 TDR...6 Precisin Resistance Measurements...7 Special Resistance / Resistive Balance...9 Cntact Resistance...9 Appendix A...10 Appendix B...11 Appendix C...15
3 Intrductin This dcument is a prcedure t verify the calibratin f the 3M Advanced Systems Tester 900AST. An internal sftware calibratin functin is prvided in the 900AST tester fr self-calibratin f internal circuits and test leads. This shuld be run n a peridic basis, r after lead replacement. T ensure the maximum accuracy this internal self calibratin shuld be run using the same adapters at the ends f the test leads as thse that will be used during measurements. The prcedure cntained in this dcument is prvided nly as an assurance t the custmer that the 900AST tester is functining within its specified precisin limits. If any f the results f these tests fail t fall within the limits given, the instrument shuld be returned t 3M fr service. Befre equipment is sent in fr repair, upgrade, and/r calibratin, yu must first get a Return Material Authrizatin (RMA) number frm the 3M Repair & Service Center. Please cntact yur 3M Repair & Service Center Custmer Service Representative, tll-free, by dialing (800) and pressing ptin #2, fr test equipment upgrades, calibratin, r warranty service. Test Instruments Required The fllwing test instruments r their equivalent are required t run the 900AST tester functinal verificatin prcedure. Agilent 34401A 6-1/2 Digit Multimeter () r equivalent Agilent 11059A Kelvin Prbe Set r equivalent Agilent 33220A 20 MHz Functin Generatr / Arbitrary Wavefrm Generatr r equivalent Tektrnix 1502C Metallic TDR Cable Tester r equivalent Tektrnix TDS 220 tw channel scillscpe r equivalent RFL Industries Mdel 828 AC/DC V-A Surce r equivalent Test Cmpnents Required The fllwing cmpnents are required fr this 900AST tester Calibratin Verificatin Prcedure. Resistr Netwrk fr Verifying RFL/Cntact Resistance/Special Resistance, see Appendix A. Capacitr film Mkt 1.0 μf 250VDC 1% radial lead Capacitr Panasnic ECG 0.01 μf (10 nf) 100V PPS film ECHS radial lead (Digikey P/N PS1103J-ND) Precisin Metal Film 1% tlerance +/-50ppm/ C 0.6W axial lead Resistrs, ne each: 135, 10.0K and 1.00M Ohm. 3 Optinal: Precisin Metal Film 1% tlerance +/-50ppm/ C 0.6W axial lead Resistrs, ne each: 1.00K, 100K, 10.0M and 115M Ohm. 20 feet RG62A/U 93 Ohm cax with Male BNC n ne end. Other end is pen. One duble female BNC cupler. Test Prcedure Self Calibratin Run the internal self-calibratin. Nte: T ensure the maximum accuracy f the 900AST tester the internal self calibratin must be run using the same adapters at the ends f the test leads as thse that will be used during measurements. With the unit n, press the tl key (4). Cursr up as necessary t highlight Self Calibrate and press the Enter key. Shrt all 5 leads tgether. Press Enter. Wait fr Calibratin t cmplete (Apprximately 2 minutes). DC Vlts Self Calibratin Cmplete? Verify tw DC vltage measurements: Select Vlts functin (blue key 1) Ensure DC Vlts is selected. Set the RFL Mdel 828 surce fr 2.0 VDC. With the surce de-energized, cnnect the red and black leads f the 900AST tester and the (in parallel) t the surce. Select OPERATE n the surce and verify the DC vltage n the 900AST tester with that measured with the De-energize the surce Change the surce t 48 VDC. Select OPERATE n the surce and verify the DC vltage n the 900AST test set with that measured with the De-energize the surce. Change the surce t 120 VDC (1K Vlts, scale factr 0.120). Select OPERATE n the surce and verify the DC vltage n the 900AST unit with that measured with the De-energize the surce. Change the surce t 250 VDC (1K Vlts, scale factr 0.250). Select OPERATE n the surce and verify the DC vltage n the 900AST unit with that measured with the De-energize the surce.
4 AC Vlts Input [VDC] [VDC] [VDC] Verify tw AC vltage measurements: Select Vlts functin (blue key 1) Ensure AC vlts is selected. Set the RFL Mdel 828 surce fr 20.0 Vrms 60 Hz VDC. With the surce de-energized, cnnect the red and black leads f the 3M Advanced Systems Tester 900AST and the (in parallel) t the surce. Select OPERATE n the surce and verify the AC vltage n the 900AST tester with that measured with the. Repeat measurement fr 400 Hz. Set the surce t Vrms 60 Hz. Select OPERATE n the surce and verify the AC vltage n the 900AST tester with that measured with the. Repeat measurement fr 400 Hz. De-energize the surce. Ohms Input [Vrms] [Vrms] 20.0 Vrms 60 Hz +/- 6 Hz Vrms 60 Hz +/- 6 Hz Vrms 400 Hz +/- 40 Hz Vrms 400 Hz +/- 40 Hz Fr resistance verificatin, the readings f the 900AST test set fr three resistrs are cmpared with thse measured with the. Using the measure and recrd the actual value f a 135, 10K and 1M hm metal film resistr. Calculate the 900AST unit's tlerance n these resistrs using the table belw: Apprximate Resistance, R Calculate, R Calculate 135 x = x = 10K x 0.99 = x 1.01 = 1M x 0.97 = x 1.03 = Select Ohms (Blue key 3) n the 900AST tester. Verify that the 900AST test set's measured value f each resistr is within the calculated range determined frm the value measured with the. Apprximate Resistance K 1M
5 Additinal accuracy ranges can be verified, but are nt necessary as the same hardware is used fr all resistance measurements. OPTIONAL: Using the measure and recrd the actual value f a 1K, 100K, 10M and 150M hm metal film resistr. Calculate the 3M Advanced Systems Tester 900AST's tlerance n these resistrs using the table belw: Optinal Apprximate Resistance, R Calculate, R Calculate 1K x = x = 100K x 0.97 = x 1.03 = 10M x 0.95 = x 1.05 = 150M x 0.90 = x 1.10 = Select Ohms (Blue key 3) n the 900AST tester. Verify that the 900AST tester measured value f each resistr is within 1% +/- 5 hms f that measured with the. Optinal Apprximate Resistance 1K 100K 10M 150M, R Capacitance Fr capacitance verificatin tw precisin (2% r better) capacitrs are used t verify the readings f the 900AST tester. Select Capacitance functin (blue key 5) n the 900AST tester. Verify that the measured value f each capacitr is within 10% f its value. ID Tne Capacitance Lw Limit High Limit 10 nf 9 nf 11 nf 1 μf 0.9 μf 1.1 μf Fr ID Tne the 900AST tester ID utputs a nminal 8 Vp-p square wave under n lad with apprximately 50% duty cycle, at the selected frequency in tw bursts, each nminal 80 ms lng, spaced abut 80 ms apart. This dual burst is repeated apprximately every 560 ms. Nte: Because the ID tne is nt cntinuus, a frequency cunter cannt be used. On the scillscpe set hrizntal scale t 250 μs/div. sweep. On the CH1 menu select Cupling DC, BW Limit Off, Vlts/Div Carse. Select 2.00 V/div. On the MEASURE menu select CH1 Freq. On the Trigger menu select Edge Vide, slpe Rising, Surce CH1, Mde Single, Cupling DC. Cnnect the red and black leads f the 900AST tester t Channel 1. Nte that since the 900AST tester is islated either lead can be cnnected t grund. Reversing the leads will affect the DC ffset, but nt the frequency reading. 5
6 Select the ID Tne functin (blue key 6) and verify that the selected frequency is 577 Hz. Press Enter t start the ID tne. Verify that the square wave frequency is 577 Hz +/- 1 Hz. In rder t btain a gd frequency measurement several samples may need t be taken by pressing the RUN/STOP buttn until a square wave is captured. TDR ID Tne Lw Limit [Hz] Frequency [Hz] High Limit [Hz] 577 Hz In rder t measure the distance t a fault by lcating the cursr at the start f the reflected pulse, the start f the rising edge f the start pulse must be at 0.0 inches. If it is nt, then the prcedure in Appendix B shuld be used t re-calibrate the TDR start pulse. Plug the supplied six ft caxial test lead in the red/black jacks. Leave the BNC end discnnected. Select the TDR functin (blue key 9) and enter TDR setup. Select the wire type as caxial. Select the Gauge as RG-8. Select First Length as Minimum. Start the TDR. If the base f the pen circuit is at 0.0 (left edge f the display), n adjustment is required. The image belw shws a TDR that requires n adjustment since the base f the pulse is a 0.0. If the base f the pen circuit is nt at 0.0 then re-calibrate its lcatin using the prcedure in Appendix B. Since the Vp f a wire in a cable bundle is specific t that cable, the verificatin f TDR is dne with a twenty ft lng 93 Ohm caxial cable whse Vp has been determined by the Tektrnix 1502C Metallic TDR Cable Tester. Determine Vp f 20 ft caxial cable: Turn n the Tektrnix 1502C Metallic TDR Cable Tester, set the dist/div t 5.0 feet. As a preliminary value, set the Vp t Adjust the <> psitin cntrl until the cursr is at the start f the rising prtin f the start pulse. Zer the meter by selecting hriz and pressing the stre buttn. Cnnect the 20 ft caxial cable t the Tektrnix 1502C Metallic TDR Cable Tester. Mve the cursr t exactly 20 feet and adjust the Vp until the cursr is at the start f the rising prtin f the reflected TDR pulse. Remve the cable and verify that the start f the rising prtin f the start pulse is still at 0.0 feet. If nt, repeat the abve. Recrd the Vp. Measure the length f the cable with the 3M Advanced Systems Tester 900AST with 3ns Pulse: Plug the supplied six ft caxial cable int the 900AST red-black input. Plug the BNC f the 20 caxial cable int the six ft caxial cable. 6
7 Turn n the 3M Advanced Systems Tester 900AST, select the TDR (blue key 9) and g int setup. Select caxial cable, and set the Vp t that previusly measured by the 1502C and press Enter. Select Single Trace and press Enter. Select the 384 range. This will autmatically use a 3ns pulse. Mve the cursr t the start f the rising prtin f the reflected pulse. Recrd this distance reading. 3ns TDR Vp f 20 cable (~0.84) Lw Limit [inches] High Limit [inches] Test lead + 20 cable Measure the length f the cable with the 900AST test set using a 5ns Pulse: Cntinuing frm the previus, 3ns measurement, press the left-right arrw key until Pulse is displayed at the bttm f the screen. Using the up-arrw key change the pulse width t 5ns. Mve the cursr t the start f the rising prtin f the reflected pulse. Recrd this distance reading. Mve the curser t 0.0 in. Verify that this is the start f the rising edge f the pulse. 5ns TDR Vp f 20 cable (~0.84) Lw Limit [inches] High Limit [inches] Test lead + 20 cable, 5ns Pulse With test lead nly, start f rising edge f 5ns pulse is at 0.0 inches Passed Precisin Resistance Measurements The same 900AST tester internal circuits are used fr Resistive Fault Lcate (RFL), Special Resistance (als called Resistive Balance), and Cntact Resistance, therefre it is nt necessary t verify bth RFL and Resistive Balance. Nte: T achieve the accuracy specificatin, the lead adapters used during 900AST tester internal self calibratin must be the same as used during these tests. Using the Agilent 34401A 6-1/2 Digit Multimeter in 4 wire resistance mde, with Agilent 11059A Kelvin Prbe Set measure and recrd the values f the resistances in the table belw f the Resistr Netwrk fr Verifying RFL/Cntact Resistance/Special Resistance (See appendix A). B Ten 1.00 Ohm resistrs in parallel t make ~ Ohms D Tw 1.00 Ohm resistrs in parallel t make ~ Ohms 1K Ohm C A 7
8 Parameter Measurement Pints Apprximate RTS (Resistance t Strap) B t C RTF (Resistance t Fault) B t D Rf (Fault Resistance) A t D 1K Resistive Fault Lcate (RFL) Verify that the RFL values f the Resistr Netwrk fr Verifying RFL/Cntact Resistance/Special Resistance fall within the specified limits. Frm the resistance values abve use the table belw t determine the acceptable RFL lwer and upper limits. Parameter Apprximate Tlerance: Lwer Limit Tlerance: RTS (B-C) = = RTF (B-D) = = Rf (A-D) 1.00K - 15 = + 15 = Make the RFL measurement and cmpare the results with these limits. Cnnect the black lead t the pen end (pint A) f the 1K hm resistr. Cnnect the red and blue test leads t the pen end (pint B) f the hm resistr. Cnnect the green and yellw test leads t the pen end (pint C) f the hm resistr. Select RFL (blue key 7) n the 900AST tester and press Enter. Wait fr the measurement t cmplete. Ensure that hms (nt distance) is selected. Verify that the Resistance t Strap (RTS) value (upper reading) is that f the measured B t C value +/ hms. Verify that the Resistance t Fault (RTF) value (left center reading) is that f the measured B t D value +/ hms. Verify that the Fault Resistance (Rf) value (lwer left reading) is that f the measured A t D value +/- 15 hms. Red & Blue Leads B Ten 1.00 Ohm resistrs in parallel t make ~ Ohms RFL VERIFICATION D A Tw 1.00 Ohm resistrs in parallel t make ~ Ohms 1K Ohm Black Lead Green & Yellw Leads C Measurement Pint RTS (B-C) RTF (B-D) Rf (A-D) Upper Limit 8
9 Special Resistance / Resistive Balance This functin is verified using the previus RFL test. Cntact Resistance Measure the precise value f the hm resistr in the resistr netwrk fr verifying RFL/Cntact Resistance/ Special Resistance. Using the values previusly measured with the, calculate the acceptable lwer and upper limits. The table belw is prvided t assist in this calculatin. Measurement Pint Apprximate Tlerance: Lwer Limit Tlerance: B t D = = C t D = = Turn n the 3M Advanced Systems Tester 900AST, select the hms functin (blue key 3). Press the left arrw t select Cntact Resistance. Cnnect the red and the blue leads t the pen end f the hm resistr (pint B) n the resistr netwrk. Cnnect the green and the yellw leads t the cmmn center (pint D) n the resistr netwrk. Press Enter and wait fr the measurement t cmplete. Cnnect the red and the blue leads t the pen end f the hm resistr (pint C) n the resistr netwrk. Press Enter and wait fr the measurement t cmplete. Measurement Pint B t D C t D Upper Limit Red & Blue Leads B t D B Ten 1.00 Ohm resistrs in parallel t make ~ Ohms CONTACT RESISTANCE VERIFICATION Green & Yellw Leads D A Tw 1.00 Ohm resistrs in parallel t make ~ Ohms 1K Ohm Red & Blue Leads C t D C 9
10 APPENDIX Appendix A: Resistr Netwrk fr Verifying RFL/Cntact Resistance/Special Resistance This resistr netwrk cnsists f three sets f resistrs wired and sldered tgether in a T netwrk. Parts required: Twelve 1.00 hm 1% 0.6W +/-50ppm/C axial leaded metallic film resistrs (Digikey P/N MRS25F-1-ND) One 1.00K hm 1% +/-50ppm/C axial leaded metallic film resistr (Digikey P/N PPC-1.00K-ND) Assembly Instructins: Parallel ten 1.00 hm 1% metallic film resistrs t create the precisin resistance left side f the tp f the T. This resistance is apprximately 0.1 hms. Parallel anther tw 1.00 hm metallic film resistrs t create the precisin resistance right side f the tp f the T. This resistance is apprximately 0.5 hms. The stem f the T cnsists f a single 1K 1% metallic film resistr. B Ten 1.00 Ohm resistrs in parallel t make ~ Ohms D Tw 1.00 Ohm resistrs in parallel t make ~ Ohms 1K Ohm C A 10
11 Appendix B: Zering the 3M Advanced Systems Tester 900AST TDR 900AST units manufactured with Versin 2.0 sftware and later have the capability f adjusting the TDR launch timing s that the start f the launch pulse is at 0.0 inches. This prcess is perfrmed during the manufacturing f the unit. If necessary it can be perfrmed in the field as n external test equipment is required. Please use the fllwing prcedure t verify that the TDR is crrectly zered t the end f the caxial test leads. 1. Insert a caxial test lead in the Red/Black jacks. Leave the BNC end discnnected. 2. G t TOOLBOX -> MAINTENANCE, enter the sequence using the keypad, and then press the [Enter] key. The unit will display Clear All fr a few secnds and then rebt. This is necessary t refrmat the system memry t prvide a lcatin fr the new TDR Launch Delay variable. Nte: Unit may require self-calibratin after perfrming this step. 3. G t TOOLBOX -> MAINTENANCE, enter the sequence 5594 using the keypad, and then press the [Enter] key. Yu will see a screen like this: If yu d NOT see a 5 next t the lwer bx, use the blue 5 key t enter a 5 in the lwer bx and press the [Enter] key. This ensures that yu are starting frm the neutral (nn-shifted) psitin initially. Nte: 5 is the zer shift value. s less than 5 shift t the right and values greater than 5 shift t the left. Yu can always return t 5 t get the initial zer shift trace. Press the [Return} key t exit MAINTENANCE and again t exit the TOOLBOX. 4. Start the TDR functin and enter TDR setup. Select the wire type as Caxial. Select the Gauge as RG-8. Select First Length as Minimum. 11
12 5. Start the TDR. Put the cursr at the base f the pen. If the base f the pen is nt visible, skip t step 9 belw. If the base f the pen circuit is at apprximately 0, n adjustment is required. The image belw shws a TDR that requires n adjustment since the base f the pulse is a If the base f the pen circuit is shifted left r right frm 0, yu can use a Maintenance cde t shift the trace int psitin. First, determine the apprximate amunt that the trace is shifted. 7. If the trace is shifted right n the screen, put the cursr n base f the pen as shwn. In this case, the base is at 14. The trace must be shifted by 14 t the left t get the base at G t TOOLBOX -> MAINTENANCE, enter the sequence 5594 using the keypad, and then press the [Enter] key. Yu will see a screen like this: 9. Refer t the Table belw fr the delay factr t use t shift the trace. In this case, select delay factr 8 t shift the pulse left by Enter 8 using the blue key 8 and then press [Enter] t accept. Press the [Return] key t exit. The adjustment factr is saved in system memry. Run the TDR functin again t verify that the base f the pulse is lcated at r near 0. 12
13 10. If the trace is nt visible n the screen because the pulse is shifted t far left (as in the image belw), the pulse must first be shifted as far right as pssible t make the pulse base viewable. 11. First, g t TOOLBOX -> MAINTENANCE, enter the sequence 5594 using the keypad, and then press the [Enter] key. Yu will see a screen like this: 12. Enter 0 using the 0 blue key. Press [Enter] t accept and then the [Return] key t exit. Press the TDR blue key t restart the TDR. The pulse will have shifted as far right (22 ) as pssible. Psitin the cursr n the base f the pulse. In this case the cursr is at 14 n the right-shifted pulse. 13
14 13. At this pint yu can determine that the pulse needed t shift = 8 t the right. Use the Table belw t determine the delay factr fr an 8 right shift. G t TOOLBOX -> MAINTENANCE, enter the sequence 5594 using the keypad, and then press the [Enter] key. Use the blue 3 key t enter a 3 and press the [Enter] key t accept. Press [Return] t exit MAINTENANCE. The shift value is nw saved in memry. Shift Directin Shift Amunt Delay Factr Right 22 0 Right Right Right Right Nne 0 5 Left Left Left Left Left Enter TDR mde and verify that the pulse is similar t the image belw t verify that the prcedure has been successfully cmpleted. 14
15 Appendix C: 3M Advanced Systems Tester 900AST Electrical Specificatins Functins Range Reslutin Accuracy Vltage (DC) Vltage (AC) 50Hz - 440Hz 0 t 99.9 V 100 t 300 V 0 t 99.9 V 100 t 250 V 0.1 V 1 V 0.1 V 1 V 1% f reading ± 0.5 V 3% f reading 1% f reading ± 0.5 V 3% f reading Ohms (resistance) N freign vltage * 0 t 9999 hms 1 hm 1% f reading ± 5 hm With freign vltage present 0 t 9999 hms 1 hm 1% f reading ± 50 hms 10 k t 99.9 k hms 0.1 k hm 1% f reading 100 k t 999 k hms 1 k hm 3% f reading 1 M t 9.9 M hms 10 k hm 3% f reading 10 M t 99 M hms 0.1 M hm 5% f reading 100 M t 990 M hms 1 M hm 10% f reading Cntact Resistance * 0 t 5 hms hm 1% f reading +/ hm Special Resistance * 0 t 25 hms 0.01 hm 1% f reading ± 0.05 hm Capacitance) 10nF t 9.9uF 1nF 10% f reading ID Tne 200 t 1000 Hz, fixed level, interrupted 1Hz +1Hz RFL * Fault range 0 t 500 K hms Resistance t Fault 0 t 15 hms hm 1% f reading +/ hm Resistance t Strap 0 t 15 hms hm 1% f reading +/ hm TDR ** Pulse width 3ns, 5ns, 34ns Fixed values Ranges (nminal, specified fr twisted pair with Vp f 0.68) 192, 384, 624, 1320, 2640, 3840, 5760, Velcity f Prpagatin 0.10 t % f range Mdes Single, Dual, Differential, Crsstalk, Memry, Peak * Measurement applies current-limited (<1mA) 80V stimulus ** Measurement applies pulse amplitude f apprximately 60Vpeak 15
16 3M is a trademark f 3M Cmpany. Other trademarks used herein are the prperties f their respective wners. Imprtant Ntice All statements, technical infrmatin, and recmmendatins related t 3M s prducts are based n infrmatin believed t be reliable, but the accuracy r cmpleteness is nt guaranteed. Befre using this prduct, yu must evaluate it and determine if it is suitable fr yur intended applicatin. Yu assume all risks and liability assciated with such use. Any statements related t the prduct which are nt cntained in 3M s current publicatins, r any cntrary statements cntained n yur purchase rder shall have n frce r effect unless expressly agreed upn, in writing, by an authrized fficer f 3M. Warranty; Limited Remedy; Limited Liability. This prduct will be free frm defects in material and manufacture fr a perid f ne (1) year frm the time f purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this prduct is defective within the warranty perid stated abve, yur exclusive remedy shall be, at 3M s ptin, t replace r repair the 3M prduct r refund the purchase price f the 3M prduct. Except where prhibited by law, 3M will nt be liable fr any indirect, special, incidental r cnsequential lss r damage arising frm this 3M prduct, regardless f the legal thery asserted. Aerspace and Aircraft Maintenance Department Transprtatin Business 3M Center, Building 220-9W-14 St. Paul, MN r Recycled paper 40% Pre-cnsumer waste paper 10% Pst-cnsumer waste paper Lith in USA 3M 2006
Burner Troubleshooting Guide
IMMEDIATE RESPONSE TECHNOLOGIES, INC. Burner Trubleshting Guide Flash Water Heater (all standard types) Created By: Stefan Swan Infrmatin in this guide was deemed technically accurate at the time f printing.
More informationUsing PayPal Website Payments Pro UK with ProductCart
Using PayPal Website Payments Pr UK with PrductCart Overview... 2 Abut PayPal Website Payments Pr & Express Checkut... 2 What is Website Payments Pr?... 2 Website Payments Pr and Website Payments Standard...
More informationiphone Mobile Application Guide Version 2.2.2
iphne Mbile Applicatin Guide Versin 2.2.2 March 26, 2014 Fr the latest update, please visit ur website: www.frte.net/mbile Frte Payment Systems, Inc. 500 West Bethany, Suite 200 Allen, Texas 75013 (800)
More informationHow To Install Fcus Service Management Software On A Pc Or Macbook
FOCUS Service Management Sftware Versin 8.4 fr Passprt Business Slutins Installatin Instructins Thank yu fr purchasing Fcus Service Management Sftware frm RTM Cmputer Slutins. This bklet f installatin
More informationFOCUS Service Management Software Version 8.5 for CounterPoint Installation Instructions
FOCUS Service Management Sftware Versin 8.5 fr CunterPint Installatin Instructins Thank yu fr purchasing Fcus Service Management Sftware frm RTM Cmputer Slutins. This bklet f installatin instructins will
More informationFOCUS Service Management Software Version 8.5 for Passport Business Solutions Installation Instructions
FOCUS Service Management Sftware fr Passprt Business Slutins Installatin Instructins Thank yu fr purchasing Fcus Service Management Sftware frm RTM Cmputer Slutins. This bklet f installatin instructins
More information990 e-postcard FAQ. Is there a charge to file form 990-N (e-postcard)? No, the e-postcard system is completely free.
990 e-pstcard FAQ Fr frequently asked questins abut filing the e-pstcard that are nt listed belw, brwse the FAQ at http://epstcard.frm990.rg/frmtsfaq.asp# (cpy and paste this link t yur brwser). General
More informationCenterPoint Accounting for Agriculture Network (Domain) Installation Instructions
CenterPint Accunting fr Agriculture Netwrk (Dmain) Installatin Instructins Dcument # Prduct Mdule Categry 2257 CenterPint CenterPint Installatin This dcument describes the dmain netwrk installatin prcess
More informationAdmission Scheduling
Admissin Scheduling The Scheduler will receive an ACE task ntifying them when the referral is ready fr the Admissin Visit t be scheduled. Same Day Admissin Visits: If Intake receives a referral requiring
More informationSIMULATIONS USING PSPICE & OSCILLOSCOPE TRAINING DRILL
SIMULATIONS USING PSPICE & OSCILLOSCOPE TRAINING DRILL In this experiment the student will explre circuit simulatins using MicrSim s Pspice fllwed by an scillscpe training drill using Virtual Bench. Pspice
More informationAdvanced Systems Tester 900AST
Advanced Systems Tester 900AST Clear skies ahead with the 900AST TESTER The internal wiring in aircraft is under constant bombardment from age, vibration and moisture especially in airplanes that work
More informationOtomasyon, Danışmanlık Ltd. Şti. INDILOAD DATACARD M AN UAL. Antetli03.doc / Page 9 of 1. Kibele Hedef mükemmele ulasmaksa.
Otmasyn, Danışmanlık Ltd. Şti. INDILOAD DATACARD M AN UAL Antetli03.dc / Page 9 f 1 Otmasyn, Danışmanlık Ltd. Şti. Chapter 1 : General Chapter 2 : Cnnectins Chapter 3 : Operatin Chapter 4 : Technical sheet
More informationPhone support is available if you have any questions or problems with the NASP PRO software during your tournament.
NASP Pr Turnament Instructins Updated 11/4/13 - NASP Pr Turnament Step by Step It is HIGHLY recmmended that yu read and fllw these instructins. Als, print these instructins and have them available at yur
More informationSBClient and Microsoft Windows Terminal Server (Including Citrix Server)
SBClient and Micrsft Windws Terminal Server (Including Citrix Server) Cntents 1. Intrductin 2. SBClient Cmpatibility Infrmatin 3. SBClient Terminal Server Installatin Instructins 4. Reslving Perfrmance
More informationDial Backup for Dedicated T1 Circuits using the ATLAS
Article ID: 1449 Q&A Dial Backup fr Dedicated T1 Circuits using the ATLAS Q: Dial Backup fr Dedicated T1 Circuits using the ATLAS A: Intrductin This technical supprt nte describes hw t cnfigure the ATLAS
More informationIntroduction to Mindjet MindManager Server
Intrductin t Mindjet MindManager Server Mindjet Crpratin Tll Free: 877-Mindjet 1160 Battery Street East San Francisc CA 94111 USA Phne: 415-229-4200 Fax: 415-229-4201 mindjet.cm 2013 Mindjet. All Rights
More information1) Update the AccuBuild Program to the latest version Version 9.3.0.3 or later.
Certified Payrll XML Exprt As f June 4 th, 2015, The Califrnia Department f Industrial Relatins (DIR) is requiring that all certified payrll reprts be submitted nline using the ecpr system. The ecpr System
More informationExcel Contact Reports
Excel Cntact Reprts v.1.0 Anther efficient and affrdable ACT! Add-On by http://www.expnenciel.cm Excel Cntact Reprts User s Manual 2 Table f cntents Purpse f the add-n... 3 Installatin prcedure... 3 The
More informationThe ad hoc reporting feature provides a user the ability to generate reports on many of the data items contained in the categories.
11 This chapter includes infrmatin regarding custmized reprts that users can create using data entered int the CA prgram, including: Explanatin f Accessing List Screen Creating a New Ad Hc Reprt Running
More informationCSAT Account Management
CSAT Accunt Management User Guide March 2011 Versin 2.1 U.S. Department f Hmeland Security 1 CSAT Accunt Management User Guide Table f Cntents 1. Overview... 1 1.1 CSAT User Rles... 1 1.2 When t Update
More informationSamsung Saga Software Upgrade for Microsoft Windows Vista Instructions
Samsung Saga Sftware Upgrade fr Micrsft Windws Vista Instructins Overview Samsung has released a sftware upgrade fr the Samsung Saga, which is recmmended t be installed. This upgrade includes numerus sftware
More informationPENNSYLVANIA SURPLUS LINES ASSOCIATION Electronic Filing System (EFS) Frequently Asked Questions and Answers
PENNSYLVANIA SURPLUS LINES ASSOCIATION Electrnic Filing System (EFS) Frequently Asked Questins and Answers 1 What changed in Release 2.0?...2 2 Why was my accunt disabled?...3 3 Hw d I inactivate an accunt?...4
More informationWelcome to CNIPS Training: CACFP Claim Entry
Welcme t CNIPS Training: CACFP Claim Entry General Cmments frm SCN CACFP claiming begins with submissin f the Octber claim due by Nvember 15, 2012. Timelines/Due Dates With CNIPS, SCN will cntinue t enfrce
More informationENERGY CALIBRATION IN DPPMCA AND XRS-FP REV A0 ENERGY CALIBRATION IN DPPMCA AND XRS-FP
ENERGY CALIBRATION IN DPPMCA AND XRS-FP Energy calibratin is very imprtant fr quantitative X-ray analysis. Even a small errr in the calibratin f the energy scale can have significant cnsequences: if the
More informationInfiniTV 4 Installation Instructions
InfiniTV 4 Installatin Instructins 1. Obtain a CableCARD frm yur cable TV service prvider 1. Call yur cable TV service prvider and tell them yu need a multi-stream CableCARD (M-Card) fr a Cetn InfiniTV
More informationefusion Table of Contents
efusin Cst Centers, Partner Funding, VAT/GST and ERP Link Table f Cntents Cst Centers... 2 Admin Setup... 2 Cst Center Step in Create Prgram... 2 Allcatin Types... 3 Assciate Payments with Cst Centers...
More informationAdobe Sign. Enabling Single Sign-On with SAML Reference Guide
Enabling Single Sign-On with SAML Reference Guide 2016 Adbe Systems Incrprated. All Rights Reserved. Prducts mentined in this dcument, such as the services f identity prviders Micrsft Active Directry Federatin,
More informationUser s Guide. Moduc Elements MagiCAD plugin
User s Guide Mduc Elements MagiCAD plugin Cntents Chapter 1. General 1 Abut this dcument... 1 Installing the sftware... 1 Required third-party sftware... 1 Installatin... 1 Starting the prgram... 2 Chapter
More informationRegions File Transmission
Regins File Transmissin Getting Started with FTPS Regins Bank Member FDIC Revised 022113 It s time t expect mre. Table f Cntents Getting Started with FTPS Setting Up FTPS Cnnectin in FTP Client 3 4 9 Regins
More informationUsing Sentry-go Enterprise/ASPX for Sentry-go Quick & Plus! monitors
Using Sentry-g Enterprise/ASPX fr Sentry-g Quick & Plus! mnitrs 3Ds (UK) Limited, February, 2014 http://www.sentry-g.cm Be Practive, Nt Reactive! Intrductin Sentry-g Enterprise Reprting is a self-cntained
More information1.0 Special Education and Conversion in MyEducation BC
1.0 Special Educatin and Cnversin in MyEducatin BC Special Educatin student eligibilities have been cnverted int MyEducatin BC frm BCeSIS. In rder t d s, special educatin wrkflw shells cntaining the designatin
More informationHP Point of Sale FAQ Warranty, Care Pack Service & Support. Limited warranty... 2 HP Care Pack Services... 3 Support... 3
HP Pint f Sale FAQ Warranty, Care Pack Service & Supprt Limited warranty... 2 HP Care Pack Services... 3 Supprt... 3 Limited warranty Q: What des a 3/3/3 limited warranty mean? A: HP Retail Pint f Sale
More informationDavid Drivers Revit One-sheets: Linked Project Positioning and shared coordinates
This paper discusses the fllwing features f Revit Building Shared Crdinates Named lcatins Publish and acquire Vs Saving lcatins Shared Crdinates and wrkset enabled files Revisin 1 (Versin 9.0) David Driver.
More informationPreparing to Deploy Reflection : A Guide for System Administrators. Version 14.1
Preparing t Deply Reflectin : A Guide fr System Administratrs Versin 14.1 Table f Cntents Table f Cntents... 2 Preparing t Deply Reflectin 14.1:... 3 A Guide fr System Administratrs... 3 Overview f the
More informationMerchant Processes and Procedures
Merchant Prcesses and Prcedures Table f Cntents EXHIBIT C 1. MERCHANT INTRODUCTION TO T-CHEK 3 1.1 Wh is T-Chek Systems? 3 1.2 Hw t Cntact T-Chek Systems 3 1.3 Hw t Recgnize T-Chek Frms f Payment 3 1.3.1
More informationMaaS360 Cloud Extender
MaaS360 Clud Extender Installatin Guide Cpyright 2012 Fiberlink Cmmunicatins Crpratin. All rights reserved. Infrmatin in this dcument is subject t change withut ntice. The sftware described in this dcument
More informationKronoDesk Migration and Integration Guide Inflectra Corporation
/ KrnDesk Migratin and Integratin Guide Inflectra Crpratin Date: September 24th, 2015 0B Intrductin... 1 1B1. Imprting frm Micrsft Excel... 2 6B1.1. Installing the Micrsft Excel Add-In... 2 7B1.1. Cnnecting
More informationTaskCentre v4.5 Send Message (SMTP) Tool White Paper
TaskCentre v4.5 Send Message (SMTP) Tl White Paper Dcument Number: PD500-03-17-1_0-WP Orbis Sftware Limited 2010 Table f Cntents COPYRIGHT 1 TRADEMARKS 1 INTRODUCTION 2 Overview 2 FEATURES 2 GLOBAL CONFIGURATION
More informationTaskCentre v4.5 MS SQL Server Trigger Tool White Paper
TaskCentre v4.5 MS SQL Server Trigger Tl White Paper Dcument Number: PD500-03-02-1_0-WP Orbis Sftware Limited 2010 Table f Cntents COPYRIGHT... 1 TRADEMARKS... 1 INTRODUCTION... 2 Overview... 2 Features...
More informationLicensing Windows Server 2012 for use with virtualization technologies
Vlume Licensing brief Licensing Windws Server 2012 fr use with virtualizatin technlgies (VMware ESX/ESXi, Micrsft System Center 2012 Virtual Machine Manager, and Parallels Virtuzz) Table f Cntents This
More informationSoftware Update Notification
Sftware Update Ntificatin PSS0223-02 Mastersizer 3000 v1.01 sftware Abstract This dcument details the release f sftware PSS0223-02 v1.01 f the sftware fr the Mastersizer 3000 laser diffractin system. It
More informationCustomer no.: enter customer no. Contract no.: enter contract no.
Annex Versin: 2.0 Specificatin f services E-mail and telephne supprt by and between (client) and secunet Security Netwrks AG Krnprinzenstrasse 30 45128 Essen Germany (secunet r cntractr) Custmer n.: enter
More informationAccess EEC s Web Applications... 2 View Messages from EEC... 3 Sign In as a Returning User... 3
EEC Single Sign In (SSI) Applicatin The EEC Single Sign In (SSI) Single Sign In (SSI) is the secure, nline applicatin that cntrls access t all f the Department f Early Educatin and Care (EEC) web applicatins.
More informationValley Transcription Service I-Phone/I-Pod App User s Guide
541-926-4194 Valley Transcriptin Service I-Phne/I-Pd App User s Guide (Fr use with iphne/ipad/i-pd Tuch) Page 0 Table f Cntents Table f Cntents... i Intrductin... 1 Requirements... 1 1. 2. 3. Installing
More informationUTO Training Bb Discussion Boards. Technical Assistance: Website: http://help.asu.edu Help Desk Phone: 855.278.5080 (24/7 support) Instruction
Bb Discussin Bards Technical Assistance: Website: http://help.asu.edu Help Desk Phne: 855.278.5080 (24/7 supprt) Instructin 1. Discussin Bard Basics Instructrs can create frums fr the curse r fr Grups
More informationOperational Amplifier Circuits Comparators and Positive Feedback
Operatinal Amplifier Circuits Cmparatrs and Psitive Feedback Cmparatrs: Open Lp Cnfiguratin The basic cmparatr circuit is an p-amp arranged in the pen-lp cnfiguratin as shwn n the circuit f Figure. The
More informationTable of Contents. Welcome to Employee Self Service... 3 Who Do I Call For Help?... 3
ALABAMA STATE UNIVERSITY HUMAN RESOURCES EMPLOYEE SELF SERVICE USER GUIDE 2 Table f Cntents Welcme t Emplyee Self Service... 3 Wh D I Call Fr Help?... 3 Hw d I access Emplyee Self Service?... 4 Persnal
More informationCopyrights and Trademarks
Cpyrights and Trademarks Sage One Accunting Cnversin Manual 1 Cpyrights and Trademarks Cpyrights and Trademarks Cpyrights and Trademarks Cpyright 2002-2014 by Us. We hereby acknwledge the cpyrights and
More informationDTU Data Transfer Utilities Software User manual
DTU Data Transfer Utilities Sftware User manual Ft. Atkinsn, Wiscnsin USA Panningen, Nederland www.digi-star.cm D3912-GB Rev A Sept 11 Table f cntents TABLE OF CONTENTS DTU Sftware general... 1 Minimum
More informationCreate a Non-Catalog Requisition
Create a Nn-Catalg Requisitin Jb Aid This jb aid describes hw t create a standard nn-catalg (i.e., nn-ibuynu) purchase request. REFER TO ADDITIONAL TRAINING GUIDES If yu need t create a special requisitin
More informationEmulation Tech Note 12 Testing XDS560V2 STM Emulator s Ethernet Port on Wi-Fi
Emulatin Tech Nte 12 Testing XDS560V2 STM Emulatr s Ethernet Prt n Wi-Fi Dcument Revisin 0.01 March 2, 2011 Page 1 f 6 TABLE OF CONTENTS 1 OVERVIEW... 3 2 HARDWARE TOOLS USED FOR TESTING... 3 3 SOFTWARE
More informationHow To Set Up A General Ledger In Korea
MODULE 6: RECEIVABLES AND PAYABLES MANAGEMENT: PAYMENT DISCOUNT AND PAYMENT TOLERANCE Mdule Overview Granting payment discunts prvides an incentive fr custmers t quickly pay their utstanding amunts in
More informationDurango Merchant Services QuickBooks SyncPay
Durang Merchant Services QuickBks SyncPay Gateway Plug-In Dcumentatin April 2011 Durang-Direct.cm 866-415-2636-1 - QuickBks Gateway Plug-In Dcumentatin... - 3 - Installatin... - 3 - Initial Setup... -
More informationHow to put together a Workforce Development Fund (WDF) claim 2015/16
Index Page 2 Hw t put tgether a Wrkfrce Develpment Fund (WDF) claim 2015/16 Intrductin What eligibility criteria d my establishment/s need t meet? Natinal Minimum Data Set fr Scial Care (NMDS-SC) and WDF
More informationFrequently Asked Questions November 19, 2013. 1. Which browsers are compatible with the Global Patent Search Network (GPSN)?
Frequently Asked Questins Nvember 19, 2013 General infrmatin 1. Which brwsers are cmpatible with the Glbal Patent Search Netwrk (GPSN)? Ggle Chrme (v23.x) and IE 8.0. 2. The versin number and dcument cunt
More information1 GETTING STARTED. 5/7/2008 Chapter 1
5/7/2008 Chapter 1 1 GETTING STARTED This chapter intrduces yu t the web-based UIR menu system. Infrmatin is prvided abut the set up necessary t assign users permissin t enter and transmit data. This first
More informationThis guide is intended for administrators, who want to install, configure, and manage SAP Lumira, server for BI Platform
Hw T install SAP Lumira, server n SAP BusinessObjects BI platfrm Distributed Install Applies t: SAP Lumira, server versin fr the SAP BusinessObjects BI platfrm Summary This guide is intended fr administratrs,
More informationSelling System Security Wire Instructions
Overview Security wire instructins are assigned at a cntract level and indicate where t send the security that is assciated with all f the lans in a Guarantr r Multilender cntract. Since security wires
More informationSamsung Omnia II Software Upgrade for Microsoft Windows XP Instructions
Samsung Omnia II Sftware Upgrade fr Overview Samsung has released a sftware upgrade fr the Samsung Omnia II, which is recmmended t be installed. This upgrade includes numerus sftware imprvements and enhancements.
More informationTraffic monitoring on ProCurve switches with sflow and InMon Traffic Sentinel
An HP PrCurve Netwrking Applicatin Nte Traffic mnitring n PrCurve switches with sflw and InMn Traffic Sentinel Cntents 1. Intrductin... 3 2. Prerequisites... 3 3. Netwrk diagram... 3 4. sflw cnfiguratin
More informationBRILL s Editorial Manager (EM) Manual for Authors Table of Contents
BRILL s Editrial Manager (EM) Manual fr Authrs Table f Cntents Intrductin... 2 1. Getting Started: Creating an Accunt... 2 2. Lgging int EM... 3 3. Changing Yur Access Cdes and Cntact Infrmatin... 3 3.1
More informationEmployee Self Service (ESS) Quick Reference Guide ESS User
Emplyee Self Service (ESS) Quick Reference Guide ESS User Cntents Emplyee Self Service (ESS) User Quick Reference Guide 5 Intrductin t ESS 5 Getting Started 6 Prerequisites 6 Accunt Activatin 7 Hw t activate
More informationInstructions for Configuring a SAFARI Montage Managed Home Access Expansion Server
Instructins fr Cnfiguring a SAFARI Mntage Managed Hme Access Expansin Server ~ Please read these instructins in their entirety befre yu begin. ~ These instructins explain hw t add a SAFARI Mntage Managed
More informationSupervisor Quick Guide
Payrll Office: ext. 7611 payrll@dixie.edu Supervisr Quick Guide This dcument prvides an verview f the daily functins and respnsibilities t be cmpleted by Supervisrs in the EMPOWERTIME Autmated Timekeeping
More informationLicensing Windows Server 2012 R2 for use with virtualization technologies
Vlume Licensing brief Licensing Windws Server 2012 R2 fr use with virtualizatin technlgies (VMware ESX/ESXi, Micrsft System Center 2012 R2 Virtual Machine Manager, and Parallels Virtuzz) Table f Cntents
More informationConnecting to Email: Live@edu
Cnnecting t Email: Live@edu Minimum Requirements fr Yur Cmputer We strngly recmmend yu upgrade t Office 2010 (Service Pack 1) befre the upgrade. This versin is knwn t prvide a better service and t eliminate
More informationGETTING STARTED With the Control Panel Table of Contents
With the Cntrl Panel Table f Cntents Cntrl Panel Desktp... 2 Left Menu... 3 Infrmatin... 3 Plan Change... 3 Dmains... 3 Statistics... 4 Ttal Traffic... 4 Disk Quta... 4 Quick Access Desktp... 4 MAIN...
More informationCreating Vehicle Requests
Overview Vehicle requisitins, including additins, replacements, dnatins and leases, are submitted, reviewed, and apprved using the State f Gergia Frms in VITAL Insights. The prcess has three levels f review
More informationAccess to the Ashworth College Online Library service is free and provided upon enrollment. To access ProQuest:
PrQuest Accessing PrQuest Access t the Ashwrth Cllege Online Library service is free and prvided upn enrllment. T access PrQuest: 1. G t http://www.ashwrthcllege.edu/student/resurces/enterlibrary.html
More informationSTIOffice Integration Installation, FAQ and Troubleshooting
STIOffice Integratin Installatin, FAQ and Trubleshting Installatin Steps G t the wrkstatin/server n which yu have the STIDistrict Net applicatin installed. On the STI Supprt page at http://supprt.sti-k12.cm/,
More informationMiaRec. Performance Monitoring. Revision 1.1 (2014-09-18)
Revisin 1.1 (2014-09-18) Table f Cntents 1 Purpse... 3 2 Hw it wrks... 3 3 A list f MiaRec perfrmance cunters... 4 3.1 Grup MiaRec Statistics... 4 3.2 Grup MiaRec Call Statistics Per-State... 5 3.3 Grup
More informationUsing PayPal Website Payments Pro with ProductCart
Using PayPal Website Payments Pr with PrductCart Overview... 2 Abut PayPal Website Payments Pr & Express Checkut... 3 What is Website Payments Pr?... 3 Website Payments Pr and Website Payments Standard...
More informationimarket Welcome Pack Version: 1.1 Status: Issued Date: 10/07/2015 Copyright 2012 Polaris U.K. Limited All Rights reserved
imarket Welcme Pack Versin: 1.1 Status: Issued Date: 10/07/2015 Cpyright 2012 Plaris U.K. Limited All Rights reserved Cntents Welcme t imarket... 3 User Types... 3 1. Getting Started... 4 2. Adding new
More informationClient Application Installation Guide
Remte Check Depsit Client Applicatin Installatin Guide Client Applicatin Installatin Guide Table f Cntents Minimum Client PC Requirements... 2 Install Prerequisites... 4 Establish a Trust t the Web Server...
More informationWireless Light-Level Monitoring
Wireless Light-Level Mnitring ILT1000 ILT1000 Applicatin Nte Wireless Light-Level Mnitring 1 Wireless Light-Level Mnitring ILT1000 The affrdability, accessibility, and ease f use f wireless technlgy cmbined
More informationNote: The designation of a Roommate is determined from the Occupants table. Roommate checkbox must be checked.
MultiSite Feature: Renters Insurance Versin 2 with Rmmates Renter s Insurance infrmatin can be tracked n each resident and rmmate, including insurance histry. Infrmatin can be edited in the Renters Insurance
More informationBasic Guide line for The Sportident system
Basic Guide line fr The Sprtident system SI-statins BSF7-8, Master statins BSM7, SI-Cnfig versin 1.4.1, 2006-10-24-1 - Index This guide line... 3 General... 3 Knwledge... 3 Mre infrmatin... 3 System requirements...
More informationRainwater Harvesting Incentive Program
Rainwater Harvesting Incentive Prgram Water Cnservatin Divisin P. O. Bx 1088 Austin, TX 78767 (512) 974-2199 fax 974-6548 Watercn@ci.austin.tx.us 10/2008 PROGRAM GUIDELINES FOR RAINWATER HARVESTING REBATE
More informationHigh Speed Internet Services
Cnventin Center High Speed Internet Services Wired high-speed Internet access inside a meeting rm, fyer r ther cmmn area: $550 fr the first IP address/device per meeting rm/lcatin, ONE TIME charge fr the
More informationELEC 204 Digital System Design LABORATORY MANUAL
ELEC 204 Digital System Design LABORATORY MANUAL : Design and Implementatin f a 3-bit Up/Dwn Jhnsn Cunter Cllege f Engineering Kç University Imprtant Nte: In rder t effectively utilize the labratry sessins,
More informationConcur Travel QuickStart Guide. Concur Technologies Version 1.0
Cncur Travel QuickStart Guide Cncur Technlgies Versin 1.0 August 22, 2014 Dcument Revisin Histry Date Descriptin Versin Authr 08/22/2014 Cncur Travel QuickStart Guide 1.0 Cncur Prprietary Statement These
More informationImproved Data Center Power Consumption and Streamlining Management in Windows Server 2008 R2 with SP1
Imprved Data Center Pwer Cnsumptin and Streamlining Management in Windws Server 2008 R2 with SP1 Disclaimer The infrmatin cntained in this dcument represents the current view f Micrsft Crpratin n the issues
More informationGUARD1 /plus. PIPE Utility. User's Manual. Version 2.0
GUARD1 /plus PIPE Utility User's Manual Versin 2.0 30700 Bainbridge Rad Sln, Ohi 44139 Phne 216-595-0890 Fax 216-595-0991 supprt@guard1.cm www.guard1.cm 2010 TimeKeeping Systems, Inc. GUARD1 PLUS and THE
More informationTelelink 6. Installation Manual
Telelink 6 Installatin Manual Table f cntents 1. SYSTEM REQUIREMENTS... 3 1.1. Hardware Requirements... 3 1.2. Sftware Requirements... 3 1.2.1. Platfrm... 3 1.2.1.1. Supprted Operating Systems... 3 1.2.1.2.
More informationUninstalling and Reinstalling on a Server Computer. Medical Director / PracSoft
Uninstalling and Reinstalling n a Server Cmputer Medical Directr / PracSft This guide describes the prcess fr uninstalling and then reinstalling Medical Directr, PracSft, and/r SQL Instances n a cmputer
More informationManual. Adapter OBD v2. Software version: NEVO-4.0.4.0. DiegoG3-3.0.8.0. Full compatibility with OBD Adapter v2 2.0B
Manual Adapter OBD v2 Sftware versin: NEVO-4.0.4.0 DiegG3-3.0.8.0 Full cmpatibility with OBD Adapter v2 2.0B Page 2 / 7 1 Descriptin The OBD Adapter v2 enables cmmunicatin between NEVO r Dieg gas injectin
More informationCallCenter@nywhere Interaction Manager OFT 605 (Part1)
Interactin Manager OFT 605 (Part1) Cpyright 2014 ICS, McGill University Table f Cntents What is Interactin Manager?... 1 Features and Benefits... 1 Launch Interactin Manager... 1 Screen Layut... 2 Cnfiguring
More informationUser Guide. Excel Data Management Pack (EDM-Pack) OnCommand Workflow Automation (WFA) Abstract PROFESSIONAL SERVICES. Date: December 2015
PROFESSIONAL SERVICES User Guide OnCmmand Wrkflw Autmatin (WFA) Excel Data Management Pack (EDM-Pack) Date: December 2015 Dcument Versin: 1.0.0 Abstract The EDM-Pack includes a general-purpse Data Surce
More informationUse the CV module within Pure to create several CVs, each targeted towards a different objective (e.g. a specific project or funding application).
Last updated: 26 Octber 2011 Create a persnal CV Use the CV mdule within Pure t create several CVs, each targeted twards a different bjective (e.g. a specific prject r funding applicatin). A CV can cntain
More informationAny symbols displayed within these pages are for illustrative purposes only, and are not intended to portray any recommendation.
WebTrader Users' Guide July 2015 2015 Interactive Brkers LLC. All Rights Reserved Any symbls displayed within these pages are fr illustrative purpses nly, and are nt intended t prtray any recmmendatin.
More informationCU Payroll Data Entry
Lg int PepleSft Human Resurces: Open brwser G t: https://cubshr9.clemsn.edu/psp/hpprd/?cmd=lgin Enter yur Nvell ID and Passwrd Click Sign In A. Paysheets are created by the Payrll Department. B. The Payrll
More informationedoc Lite Recruitment Guidelines
edc Lite Recruitment Guidelines Intrductin OneStart & the Academic Psitin Search Channel edc Lite Ruting and Wrkgrups Ruting Actin List Ruting Cntrls Wrkgrups Dcument Search edc Lite Dcuments Vacancy Ntice
More informationTaskCentre v4.5 File Management Tool White Paper
TaskCentre v4.5 File Management Tl White Paper Dcument Number: PD500-03-30-1_0-WP Orbis Sftware Limited 2010 Table f Cntents COPYRIGHT 1 TRADEMARKS 1 INTRODUCTION 2 Overview 2 FEATURES 2 TECHNICAL SUMMARY
More informationICD-10 Handbook APPLICATION MANUAL
APPLICATION MANUAL Table f Cntents Definitin...3 Billing...3 Transactin Cdes...3 Diagnsis Cdes...3 PQRS Measures (frmerly PQRI Measures)...5 Parameters...5 System Wide Defaults...5 System...5 Patient Definitin...6
More informationIntroduction LIVE MAPS UNITY PORTAL / INSTALLATION GUIDE. 2015 Savision B.V. savision.com All rights reserved.
Rev 7.5.0 Intrductin 2 LIVE MAPS UNITY PORTAL / INSTALLATION GUIDE 2015 Savisin B.V. savisin.cm All rights reserved. This manual, as well as the sftware described in it, is furnished under license and
More informationCalibration of Oxygen Bomb Calorimeters
Calibratin f Oxygen Bmb Calrimeters Bulletin N.101 Prcedures fr standardizatin f Parr xygen bmb calrimeters. Energy Equivalent The calibratin f an xygen bmb calrimeter has traditinally been called the
More informationJuniper Networks Product End-of-Life
Juniper Netwrks Prduct End-f-Life Plicy & Prcedure ( EOL Plicy ) Frm time t time, Juniper Netwrks may find it necessary t discntinue prducts and services fr a number f reasns, including technlgy innvatins
More informationPerl for OpenVMS Alpha
Perl fr OpenVMS Alpha Installatin Guide and Release Ntes January 25, 2002 Perl fr OpenVMS Versin 5.6.1 CPQ-AXPVMS-PERL-V0506-1-1.PCSI-DCX-AXPEXE On this page yu'll find infrmatin abut: Sftware prerequisites
More informationSystem Business Continuity Classification
System Business Cntinuity Classificatin Business Cntinuity Prcedures Infrmatin System Cntingency Plan (ISCP) Business Impact Analysis (BIA) System Recvery Prcedures (SRP) Cre Infrastructure Criticality
More information