Manual Headend Controller (HCB 100 blue ( )

Transcription

1 Mnul Hedend Controller (HCB 100 blue ( ) Chnges due to technicl progress possible! Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

2 CONTENT 1. Set up of the network connection WINDOWS XP WINDOWS Set up of the Web browser Microsoft Internet Eplorer Working with the Hedend Controller (HCB 100) Cll up the Hedend Controller Selection of the desired Hedend overview Selcection of Adjustments nd Configurtions Bsic settings of the Hedend Controller Reset of the HEADEND CONTROLLER Configurtion of the HEADEND CONTROLLER Mnul strt of NIT - distribution Timer / Time controlled switching Adjustment of Dte/Time Cold strd of individul/single modules Chnge of User ID, Pss word Additionl NIT - Dts Protocoll / Log book Updte of the HEAEND CONTROLLER Digrmm for the mnul opertion/mngement of the HCB Configurtion of the HCB Adjustment possibilities of IP - Numbers Generl Informtion for djustments of the IP - Number LCD disply t the HCB Initilizing of the modules fter RESET Stndrd Disply Error disply, if module cn not be clled up Chnges of the Hrdwre Additionl Network components Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

3 1. Set up of the network connection 1.1 WINDOWS XP - Entering vi Strt button of your desktop nd then cll up System opertion Confirm LAN - connection with douple click (continue t pge 4) 3 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

4 TCP/IP Protocol not instlled TCP/IP Protocol instlled Select Use the following IP - Address!!! NOTICE - Enter vlid IP - Address nd Subnet msk. - The IP - Address of the PC/Lptop hs to be different (lst two figures) of the IP - Address of the HCB The Subnet msk cn be entered s shown in the bove emple. NO entries for Gtewy, DNS... re necessry. Select TCP/IP nd then press OK 4 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

5 1.2 WINDOWS Entering vi Strt button of your desktop nd then cll up System opertion vi Adjustments Confirm LAN - connection with douple click (continue t pge 4) 5 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

6 TCP/IP Protocol NOT instlled TCP/IP Protocol instlled Select Use the following IP - Address!!! NOTICE - Enter vlid IP - Address nd Subnet msk. - The IP - Address of the PC/Lptop hs to be different (lst two figures) of the IP - Address of the HCB The Subnet msk cn be entered s shown in the bove emple. NO entries for Gtewy, DNS...necessry. Select TCP/IP nd then press OK 6 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

7 2. Set up of the Webbrowser 2.1 Microsoft Internet Eplorer - Open the Webbrowser, select Etrs snd then Internet Option Generl settings Adjustments for Connections Select No connections Select Every visit to the pge!!! Notice To void disply errors plese chnge the, djustments for the storing oftemporry Internet files. Plese disconnect the ccess to Proyserver for direct connection of the HCB 100 with PC/Lptop. Plese restrt the PC/Lptop fter ll settings/djustments re finished. Then the connection to the Hedend Controller HCB 100 cn be clled up vi the Webbrowser. 7 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

8 3. Working with the Hedend Controller HCB Access to the Hedend Controller Enter the IP - Number into the ddress - line. (IP - Number e works BLANKOM is ) The Login - window of the HCB 100 will be displyed if ll djustments/settings re correct. You now cn sve/secure the opertion vi pssword. Selecting the configurtion Automtic Login llows i Login without pssword entry (see 3.4.2). 8 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

9 Enter USER ID nd psswordt USER ID nd Pssword e works BLANKOM: User ID Psswordt Writing protection hs been deleted. You will be utomticlly forwrded to the Selcetion - Menu. Selection of desired Hedend overview tble (see 3.2) Selection of Adjustments nd Configurtions (see 3.3) 9 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

10 3.2 Selection of the desired Hedend overview tble Hedend overview (LIST) The Hedend overview (List) displys ll the modules of the entire Hedend system s List. Selecting the button Edit gets you to the opertion overview of the respective module. Hedend overview tble (Mtri) The Hedend overview (Mtri) displys ll the modules of the entire Hedend system s Mtri. - The first line (horizontly / here 02 nd 03) displys the line-ddresses of the Bus-Etender/Power supply (BEB 100). - The fist line (verticly / here 01-07) displys the ddresses of the individul modules. s well s dditionl informtion like the module type, the synchronistion (SYNC) for digitl converters, chnnel nme(s), respective output bnd nd -frequencyies Selecting the button Edit gets you to the opertion overview of the respective module. Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

11 Hedend overview tble (Button) The Hedend overview tble (Button) displys ll the modules of the entire Hedend system with vrious configurtion buttons. Following functions cn be selected: Edit Die Bedienoberfläche des jeweiligen Moduls wird geöffnet und es können Einstellungen vorgenommen werden. Copy (dt pge) ON / OFF Ouput ttenution Sttus The Copy (dt pge) of the desired module will be processed. It displys ll djusted prmeters nd cn be sved/stored. (Store/sve within Internet Eplorer: Dt/File Sve trget t/s ) The menu All enbles the processing of copy/dt pge for the entire Hedend system. NOTICE: The Copies/dt pges will be stored/sved with new form nd re NOT downwrds comptible. These cn not be used with the HCB 100 module types ( / ). A menu with ON, OFF or RESET will be displyed - Selecting ON or OFF llows you to chnge the opertion sttus of the desired module - Selecting RESET will disconnect/switch off the desired module for 8 seconds. Selecting Output ttenution enbles you to chnge the output level of the desired module. The operting sttus of the desired module will be clled up nd displyes. - Selecting the button Hedend red out effects Scn of the entire Hedend system including ll connected modules. - Selecting the button check-out occurs n utomtic log out of the hedend system - Selecting the button Selection gets you to the selection menu of the hedend system. 11 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

12 3.3 Selcection of Adjustments nd Configurtions Hedend level settings (List) Module informtion (Mtri) The Mtri overview displys the prt n, current softwre nd the seril n of the respective module. For djustment/setting of signl-level for ech module of the hedend Enter Trnsmit to confirm desired/selected level. Hedend Controller - Displys ll setting/djustment opportunities of the entire hedend or for individul modules. - Displys the IP - number, the current softwre of the Hedend Controller HCB Bsic settings/djustments in prt The button Nme llows the desired nme for the hedend. - The button Lnguge llows the selection between Germn & Englisch. 12 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

13 3.4 Bsic settings/djusments for the Hedend Controllers Reset of the HEADEND CONTROLLER Ente RESET effects restrt of the HEADEND CONTROLLER nd softwre reset is done lso. Afterwrds hedend red out is done Konfigurtion HEADEND CONTROLLER Sub-Menu for ctivtion of dditionl functions for the Hedend controller HCB 100. Address select. (mnul opertion) ON... Mnul selection is done vi Up / Down key-pds of the HCB 100 OFF... Selection is done vi direct entry of line- nd device ddresses All chrcters (mnl opertion) ON... Tet input for ll chrcters possible OFF... Tet input only for 0-9 und A - Z possible NIT - Distribution ON... NIT - dts will be echnged dynmiclly OF... NIT - dts will be switched OFF NIT - Rck A NIT - Rck B Emple:* Notice: Specil djustments hve to be done when interchnging NIT - dts of two HCB 100 or one HCB 100 with dditionl NIT - dts NIT - Rck A NIT - Rck B HCB 100 with 32 STB 606** OFF OFF HCB 100 Rck A with 16 STB 606** EIN OFF HCB 100 Rck B with 16 STB 606** OFF ON dditionl NIT - dts ON... input of 16 eternl trnsponder informtion possible OFF...NO dditionl inputs possible Key lock ON... mnul settings/djustments directly t HCB 100 dectivted OFF... mnul settings/djustments directly t HCB 100 ctivted Automtic Login ON... Writing protection is dectivted. Access to the Menu without pssword entry possible. OFF... Entry of User ID & Pssword necessry for ccess to the menu A Timer / Time controlled switching ON... time controlled chnges/switching is possible/ctivted AUS... time controlled chnges/switching dectivted * Ml 32 NIT - Dts of the B-LINE - modules cn be processed. (16 Rck A + 16 Rck B) or (16 B-LINE + 16 eternl) **Vlid for following B-LINE modules: STB 606, STB 607, STB 006, AMB 206, CTB Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

14 3.4.3 Mnul NIT-Distribution Press Str Mnul NIT - Distribution for n one time NIT - Distribution. Pls. see more detiled informtion for NIT-Distribution t our website, Timer / Time controlled switching Timer / Time controlled switching llows time controlled switchover of progrms. NOTICE Time-synchroniztion of the HCB100 is done with reference time (see 3.4.5). NOTICE - Input of prmeters/vlues into the timer hs to be done in the sequence of the opertor interfce of the respective module (see pge 17 for the sequences of the module) - Upper nd lower cses hve s well s the input of the dimensions (e. G. MHz) hve to be considered Timer / Time controlled switching is OFF - NO input windows re enbled - Press Configurtion to go to the menu Configurtion for Hedend Controller - To enble the configurtion tble press Timer/Time controlled switching to ON. 14 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

15 Beispiele HCB 100 Timer This menu is for the configurtion of time controlled switching nd will only be displyed when the Timer-Mode is ctivted. Emple 1 (Specil cse) Switching of 2 modules vi RF - disconnection (switching itme ppro. 1-2 sec.) 5:00 hrs. Address 00/03 will be switched off Addresse 00/04 will be switched on 7:00 hrs Address 00/04 will be switched off Address 00/03 will be switched on Emple 2 Progrm switchover for MPEG - modules KIKA TV-Progrm switched to ANTENNE Byern Rdio - Progrm (Switschtime ppro. 10 sec.) Emple 3 (Specil cse) Progrm switchover for nlogue signls C-LINE TWIN-Module 8:00 hrs. ctivtion for chnnel 1 20:00 hrs. ctivtion for chnnel 2 The desired chnges hve been entered s displyed t the html - opertion surfce. e. g. Operting sttus: ON or OFF 15 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

16 Progrm switchover (Emple for KIKA-TV / Antenne Byern-Rdio) Differences specil configurtion for KIKA: Nme = KIKA SAT-IF = 1354 ServiceID = Service Type = TV specil configurtion for Antenne Byern: Nme= Antenne Byern SAT-IF = 1548 ServiceID = 170 Service Type = Rdio NOTICE! Plese consider tht only the vlues which re desired to be chnged for switchover hve to entered within the configurtion window.n. Also the desired switchtimes for the switchover of the desired progrms hve to be selected. NOTICE! If progrms (e. G. KIKA) re to be switchedover by fied brodcsting-times, then plese to NOT progrm the switchover time!!! 16 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

17 Progrm selection for the C-LINE hedend system (specil cse vi RF - Signl) Differences Switching condition chnnel 2 ON : Progrm = Sonnenklr TV Output frequency = 503,25 MHz (K25) Switching condition chnnel 1 ON : Progrmm = HSE Output frequency = 503,25 MHz (K25) Emple - Currently chnnel 1 (HSE) is ctiv - Output chnnel for timer controlled switchover is K25 - As desired Sonnenklr-TV will be switched ON nd HSE24 will be switche OFF t 20:00 hrs.. ctivted chnnel Only the ctive chnnel hs to be selected for this configurtion. No further entries necessry This time controlled switchover llows to chnge/switchover progrms of different levels within one modul without n dditionl RF - switch. Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

18 Further informtion for timer configurtion RF - Signl: This prmeter is only vilble t the 1. selection bo. Not ll modules support this configurtion. This cn be done only if the respective module supprt switching/selection of the RF-signl (see pge 18) Übernhme: This function is only vilble t the 8. selection bo The djustments of the input prmeters will be overtken without reset (see tbel pge 20). Color br: When color br is ON then nd dts will be sent to the module then the Frbblken will be switched off Following configurtions hve to be done. Prmeter-List TV-picture with Frbblken ON 1. selection bo 8. selection bo Emple for n Einstellbo (Address, Switchtime, Prmeter, Werte) 18 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

19 Possible prmeters for timer controlled switchover Prmeter Chnnel (only Nme SAT-IF QPSK-Symbol rte Service ID Lnguge n Service Type Adjustement code Prmeter C-LINE) Chnnel (only Nme SAT-IF QPSK-Symbol rte Service ID Lnguge n Service Type Adjustement code C-LINE) SAT-Sound frequency Input frequency Spectrum inversion QAM-Symbol rte IF bndwith Frbblken Operting sttus Übernhme RF.-signl STB SAT-Sound frequency Input frequency Spectrum inversion QAM-Symbol rte IF bndwith Frbblken Operting sttus Übernhme RF.-signl STC SDB TCC STB STC STC STB VMC TTB TTC UCB CCB TCB CTB VMB ATB ADB b Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

20 3.4.5 Adjustment of Dte/Time 3 Options for Dte & Time configurtion vi the Hedend Controller HCB Time cn be configured mnully, synchronised with the PC/Lptop-time or dopted from n digitl converter Mnul correction of Dte/Time - Press Trnsmit for cceptnce/storge Synchroniztion of Dte/Time with connected PC/Lptop - Press Trnsmit to Confirm ccept PC-Time Select ddress of module to dopt its time (Cn be done with ll hedend modules) [-/- = die Adressuswhl erfolgt utomtisch] - Press Trnsmit for cceptnce Offset time, for time correction of desired/selected ddress Aktuliztion/Updte of Dte/Time for displyed module Overview of ll modules which provide Dte & Time. The reference ddress cn be selected directly in this window NOTICE! Disply of the dte for digitl Trnsmodultors possible only from sofwre-version V1.68 of the MPEG-Module Cold strt of single modules Entry of the sytstem cold strt time (e.g. 03:00 hrs.) ( Cold strt is dectivted when entering 00:00 hrs.) Time lignment * ON... Time ligment will be done fter restrt of the module OFF... No Time ligment fter restrt of the module Mtri for ll vilble modules - Selection of the module for restrt - Select All (ll modules will be considered) - Delete module-selection will be relocted nd restrt configurtions - Trnsmit for cceptnce of cold strt configurtions - Mnul restrt of selected/modules 20 * Die Zeitktulisierung erfolgt bei ktivierten Neustrt uch wenn für kein Modul ein Neustrt vereinbrt wurde. Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

21 3.4.7 Chnge User ID, Pssword Access rights for 1 Min-Administrtor nd for up to 15 Sub-dminsitrtors cn be edited!!! Rights for Min-Administrtor - Full rights for configurtion/mngement/chnges for the hedend system - To provide nd to chnge User Id s nd Psswords for the Sub-Administrtors Rights for Sub-Administrtors - The Sub-Adminsitrtors only hve the right to do ny for chnges/configurtion/mngement of the hedend 21 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

22 3.4.8 Additionl NIT - Dts Entering/Using dditionl NIT - dts of previous BLANKOM hedend systems (e.g Profi 800- or MINISAT system) or even of hedend system of other suppliers llows lso both the distribution of this nd of NIT - Dts of the B-/C-LINE hedend systems. This function hs to be ctivted t the Configurtion menu for the Hedend Controller HCB 100. Then tble for 16 mnul entries is vilble. The vlues for output frequency, modultion nd QAM symbol rte of the respective chnnels re known. The Trnsport strem - ID nd the ORIGINAL Network-ID cn be selected/seen with QPSK-QAM Trnsmodultor (STB606/607 or STC696/697) or with respective test device. Emples for Trnsport strem - ID nd Originl Network - ID Trnsponder Downlink (MHz) Symbol rte (MSps) SAT-IF (MHz) Trnsport strem - ID Hel Deziml Originl-Network - ID Hel Deziml ,500 27,500 27,500 27,500 27,500 27,500 27,500 27,500 27, (3) (17) (2) 0044D (1101) (6) (1079) (4) (5) (1073) (133) (133) (133) (1) (133) (1) (133) (133) (1) Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

23 3.4.9 Protocoll / Logbook The HCB 100 contins of Protocoll/Logbook system - Up to 127 events cn be stored - Every entry displys dte, time nd informtion of the respective events. (The ltest/lst input/entry is lwys displyed bove the green line) The Protocoll registers/stores different ccesses nd its relted events to the hedend system: Logon nd Logoff vi the Browser (User ID / Pssword) Chnges of the mimum- nd minimum vlues for temperture nd voltge Activtin of the Timer Strt of NIT - distribution Reset of the Hedend controller HCB 100 Chnging of djustments/configurtions (Writing protecton to the module will be registered) ALL CHANGES WILL BE STORED AND DISPLAYED WITH DATE AND TIME INFORMATION ONLY IF THE CLOCK OF THE HCB 100 IS SYNCHRONIZED 23 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

24 Updte of the HCB 100 (internl softwre) 1. Connect PC/Lptop to the Hedend Controller HCB 100 (directly connection or vi network) 2. Select the configurtion pge for the HEADEND CONTROLLER t the selection menu Smple hedend sttion Lod Dts (vlues) or softwre Serch Select Uplod files* HCB_100_Up_V2.tt Select Uplod to strt the updte function Serch Uplod is running!!! Uplod ws successful! Strt softwre-updte then! 24 * The uplod/updte file hs to be stored s.tt file t the PC/Lptop. NO zip - dt/file cn be stored with the HCB 100. Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

25 Disply for ll versions vilble with this updte. The connection circuit bord Anschlussleitertpltte (APL) versions will be culized utomticlly lso Strt softwre updte - Durtion for HCB 100 updte ppro 2 Min. - Disconnect possible ethernet-connecton before strting the updte nd during upd. - Durtion for the APL updte ppro. 15 sec./per module *) - Firmwre-Updtes for the modules cn much more longer (Meldung HCB: Softwre updte) *) Bootloder Feedbck: Strt Softwre updte - Updtes runs utomticlly!!! NO ccess to the HCB 100 during the updte possible!!! BLANKOM Antennentechnik Updtes runs utomticlly Softwreupdte BLANKOM Antennentechnik ENTER 13:01 Updte is finished when ENTER nd the TIME is displyed t the HCB 100 END of Updte 25 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

26 b 4. Flussdigrmm for mnul opertion of the HCB 100 ENTER BLANKOM Modules/Cssettes Select module ddress Type / Prt N OK Chnge Module ( see device mnul of respective module) NIT - Distribution Displys NIT-Verteilung eecution Any key Temperture Displys Temperture Any key Voltge Displys Voltge Any key Current Displys Current Any key Configurtion Chnge configurtion 1 11 Contrst Displys/Selection +/- Version Displys Version Any key Reset System reset IP - Number Chnge IP - Number 2 21 Bck ENTER Up Down 26 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

27 4.1 Configurtion of the HCB 100 Configurtion chnge 1 1 Address selection Direct input or selection All signs All or numbers nd cpitl letters Mtriview Module overview s list or mtri NIT - distribution Implement or do not implement NIT - Rck A 1. HCB 100 in the NIT - Dt echnge NIT - Rck B 2. HCB 100 in the NIT - Dt echnge End Adjustments for IP - Numbers 4.3 Generl routine for djustment of the IP - Numbers 2 IP - number Webserver or zz (see fig. on the right side) IP - number chnge 2 Subnet Msk Gtewy DHCP - IP or zz (see fig. on the right side) or zz (see fig. on the right side) or zz (see fig. on the right side) NO Chnge JA 4. Byte (MSB) VEA - IP or zz (see fig. on the right side) 3. Byte Trp - IP (SNMP) * or zz (see fig. on the right side) 2. Byte 1. Byte (LSB) * Option 27 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

28 5. LCD Disply t the Hedend Controller HCB 100 Strt... V2.22 / IP-Nummer Strt of the HCB 100 ==> Current softwre version of HCB 100 is displyed Strt... V2.22 / Puse... 8s Power ON RESET occurs n dditionl running-time for for the self initiliztion of the modules 5.1 Initiliztion of the modules fter RESET Serch... BUS-Etender BEB 100 ADDR Serch... BUS-Etender BEB 100 ADDR Serch for BUS-Etenders BEB 100 (used with of the hedend system) ==> Displys ll found BEB 100 Serch for BUS - Etendern BEB 100 is finished ==> Displys the found BEB 100 with respective ddresses (here 1, 2, 3, 4 und 5=5BEB100refounded) Serch... BEB 100 ADDR 02 Module ADDR Serch... BEB 100 ADDR 02 Modules ADDR Serch for modules of line 2 ==> Displys ll found modules Serch for modules of line 2 is finished => Displys the found BEB 100 with respective ddresses 5.2 Stndrd Disply Suche... BEB 100 ADDR 02 BEB 100 ADDR - - Enter 15:23 Suche... BEB 100 ADDR 02 BEB 100 ADDR - - NIT - Verteilung HCB 100 is in opertion mode (works correctly) ==> Green LED is on. HCB 100 is doing Dtenustusch between QSPK/QAM-Modules ==> Yellow Led is blinking 5.3 Disply of Errors, if module is not supported HCB 100 tried to detect module which is not supported. TTT TTT ZZZZ. ZZ Softwre updte! Press ny key TTT TTT ZZZZ.ZZ Inde of the module recognized Type Inde of thehcb 100 red out drwing number 28 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

29 6. Chnge of hrdwre (remove, d or chnge modules) The internl memory of the HCB 100 ssures bckup (Copy) of the hedend configurtion. If module will be chnged/removed or new one will be dded then the HCB 100 hs to relod this new hrdwre Press Hedend red out ==> New/chnged configuriton will be scnned (new scn) NOTICE No communiction/ccess to the HCB 100 possible The selection menu is vilble fterr successful scn is finished INFORMATION A Reset/Restrt cn be done within the menu of the Hedend Controller or t the HCB 100 directly. ==> The hedend will lso be scnned then Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

30 7. Additionl network components Interconnection of severl Hedend Controllers HCB 100 nd combintion with different ctivtions: - At site opertion/mngement/djustment with PC/Lptop (Direct connection between PC/Lptop nd HCB 100) - Remote control/mngement vi Ethernet - Remote control vi Router (ISDN, Modem, WLAN) Connection to one or more HCB 100 directly with PC/Lptop Lptop or Ethernet IP-Number 1 HCB 100 IP-Number 2 1. HCB 100 IP-Number 2 Lptop or Ethernet IP-Number 1 HUB / SWITCH 2. HCB 100 IP-Number 3 3. HCB 100 IP-Number 4 Connection to HCB 100 with PC/ Lptop vi WLAN Lptop WLAN crd Ad-hoc IP-Number 1 Wireless Access Point 1. HCB 100 IP-Number 2 IP-Number 3 Connection to HCB 100 with PC/ Lptop vi ISDN - Router ISDN ISDN-Router HCB 100 IP-Number 1 IP-Number 2 ISDN ISDN-Router HUB / SWITCH 1. HCB 100 Bsp. X1000 von Bintec 30 IP-Number 1 t 2. nd 3. HCB 100 IP-Number 3 und 4 IP-Number 2 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /

31 Connection to HCB 100 vi n nlogue - Router nlogue Telephone connection Router with integrted Modem IP-Number 1 HCB 100 IP-Number 2 nlogue Telephone connection Router with integrted Moddem IP-Number 1 Emple: Prestige 100 MH from ZyXEL HUB / SWITCH t 2. nd 3. HCB 100 IP-Number 3 nd 4 1. HCB 100 IP-Number 2 Network of severl HCB At site Controll/Mngement/Adjustments - REMOTE Controll/Mngement/Adjustmentsvi network connection - REMOTE Controll/Mngement/Adjustments vi Router Lptop 1. HCB 100 IP-Number 2 Ethernet (LAN / WAN) HUB / SWITCH with minimum 6 Port s 2. HCB 100 IP-Number 3 ISDN ISDN-Router 3. HCB 100 IP-Number 4 31 Hermnn - Petersilge - Strße 1 D Bd Blnkenburg Germny Phone: (0) /60-0 Telef: (0) /