RRC-1258 MkII(s) m crob t. Yaesu Twin, Elecraft K3-Twin etc. User Manual USER MANUAL RRC-1258 MKII. User manual Rev. A Maj 28 1 of 233

Transcription

1 RRC-25 MkII(s) Yesu Twin, Elecrft K3-Twin etc. User Mnul B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

2 Tble of contents Sttement of Conditions... 7 Generl Description... Detchble control pnel... 9 PC-bsed control... 0 Step by step system setup... Hrdwre... 3 Front... 3 Bck... 7 Strpping nd jumpers... 2 Configurtion with Microbit Setup Mnger... 2 FW/HW version FW updte Setup Net info WiFi nd Seril Port tbs Initil IP setup... 3 Configurtion with WEB-interfce Info Sttus... 3 Profiles... 3 IP Settings Rdio Settings Seril Settings Advnced settings... 5 Dynmic DNS setting (only Rdio-RRC)... 0 Remoterig dynmic dns service... 0 DynDNS dynmic dns service... 3 Keyer Settings (Control-RRC)... 5 Keyer Settings (Rdio-RRC)... 7 IO Settings... 9 Ping settings (only Rdio-RRC) Wi-Fi settings Export settings (HTML) Export settings (bin) Import settings (bin)... 7 Appliction firmwre upgrde Bootloder firmwre upgrde... 7 Restrt device... 7 Configurtion with terminl-interfce WiFi... 0 Generl... 0 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

3 Connecting to Wifi network... CW-Keyer... 7 Generl... 7 Settings... 7 Connections... RTTY Keying Generl RTTY with MMTTY Settings Connections ICOM CI-V... 9 Generl... 9 Hrdwre configurtion... 9 Rdio settings (exmple) Connections ICOM IC Generl... 0 Hrdwre configurtion... 0 Rdio settings (exmple) Connections Power supply ICOM IC-703, IC Generl Hrdwre configurtion Rdio settings (exmple) Connections Power supply... 0 Prepre the seprtion cble to IC-703 nd IC ICOM IC-R Generl... 2 Hrdwre configurtion... 2 Rdio settings (exmple)... 2 Connections... 3 Power supply... 3 ICOM IC-E Generl... Hrdwre configurtion... Rdio settings (exmple)... Connections... 7 Using HM-33 Microphone... Power supply ICOM ID-E Generl Hrdwre configurtion B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 3 of 233

4 Rdio settings (exmple) Connections HM-33/0 Microphone dpter bords Modifictions of the Control-RRC circuit bord... 2 Modifictions of the Rdio-RRC circuit bord... 2 Power supply ICOM IC Generl Hrdwre configurtion Rdio settings (exmple)... 3 Connections... 3 Power supply... 3 YAESU TWIN Generl Hrdwre configurtion Rdio settings (exmple)... 4 Connections Logging or computer control, RTTY etc YAESU FT Generl Hrdwre configurtion Connections Power supply YAESU FTM Generl Hrdwre configurtion Connections Power supply YAESU FT-700/00/ Generl... 0 Hrdwre configurtion... 0 Connections... 2 Power supply... 2 YAESU FT-97, FT-000 etc Generl... 4 Hrdwre configurtion... 4 Rdio settings (exmple)... 5 Connections... 5 YAESU in Generl (FT-2000) Generl Hrdwre configurtion Rdio settings (exmple) Connections... 7 KENWOOD in Generl B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 4 of 233

5 Generl Hrdwre configurtion Rdio settings (exmple)... 7 Connections... 7 KENWOOD TS Generl... 0 Hrdwre configurtion... 0 Rdio settings (exmple)... Connections... Power supply... 2 KENWOOD TM-D Generl... 5 Hrdwre configurtion... 5 Rdio settings (exmple)... Power supply... KENWOOD TM-D Generl... 9 Hrdwre configurtion... 9 Rdio settings (exmple) Power supply KENWOOD TS Generl Hrdwre configurtion Rdio settings (exmple) Connections ELECRAFT K3-Twin... 9 Generl... 9 Hrdwre configurtion... 9 Rdio settings (exmple) Connections Connections Logging or computer control, RTTY etc ELECRAFT Generl Hrdwre configurtion Rdio settings (exmple) Connections ALINCO DX-SR nd DX-R Generl Hrdwre configurtion Rdio settings (exmple) Connections Power supply RRC-25MkII with 2-wire or 4-wire interfces... 2 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 5 of 233

6 Generl... 2 Hrdwre configurtion... 2 Rdio settings (exmple) Connections Power supply Schemtics I/O nd PAD interfce... 2 MIC/AUX Interfce Control-RRC MkII Speker output interfce Control-RRC MkIIs Speker input interfce Rdio-RRC MkIIs MIC/AUX Interfce Rdio-RRC Networks nd Firewlls DMZ Portforwrding SIP ALG Mobile Network Routers Appendix B - COM-port Keyer interfce Appendix D - Technicl Dt Appendix E - Sfety nd Regultory Informtion FCC Sttement Sfety Notice Disclimer FCC / CE - Declrtion of conformity B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

7 Sttement of Conditions In the interest of improving internl design, opertionl function, nd/or relibility, Microbit 2.0 AB reserves the right to mke chnges to the product described in this document without notice. Microbit does not ssume ny libility tht my occur due to the use or ppliction of the product(s) or circuit lyout(s) described herein. All prts of the softwre re property of Microbit 2.0 AB. The hrdwre design, schemtics PCB lyout, concept, grphics, user mnul, etc. re property of Microbit 2.0 AB. The device my not be disssembled, copied or reversed engineered. Copyright 200,20,202,203 Microbit 2.0 AB All rights reserved. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 7 of 233

8 Generl Description The Remoterig RRC-25MkII (RRC) is developed especilly for remote control of Amteur rdio sttions vi the Internet in user-friendly nd cost-effective wy. The RRC units re used in pirs, one is connected to the rdio (Rdio-RRC) nd the other is connected to the control equipment (Control-RRC). The system is unique in the wy tht no PC is needed for the voice nd dt communiction it s hndled by the two RRC. There re two versions vilble RRC25MkII nd RRC25MkIIs, the difference is tht the (s) versions hndles two udio chnnels from the rdio which is useful together with dul receiver equipment. The Remoterig system cn be configured to work together with most Amteur rdio sttions vilble on the mrket from ICOM, Kenwood, Yesu, Elecrft, Alinco nd Tentec. The Remoterig system fits very well in the following situtions: You re not llowed to put up ntenns t your home. The noise level is too high to mke Amteur rdio ctivity possible. You wnt to build so big ntenns tht cn t be done in urbn res. You do not wnt to be dependent of PC:s for the remote control. Etc. The Remoterig system itself will not introduce ny ltency nd the ltencies introduced by Internet nd buffering will rrely be ny noticeble problem. The Remoterig system lso includes unique solution for operting CW over Internet nd it lso includes CW-keyer. The Remoterig system is connected to the Internet primrily vi 0 or 00 Mbit Ethernet nd fixed connections like DSL, cble nd WLAN. 3G bsed mobile solutions will lso work but sometimes with reduced performnce. The system is portble nd you cn use it from lmost ny network connection in the world. Session control, udio (VoIP) nd dt is trnsferred using stndrdized protocols like SIP, RTP etc. where you cn select different udio qulities depending on vilble bndwidth. The RRC-25MkII is esily configured vi modern USB nd WEB bsed user interfces. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

9 Detchble control pnel You will get the ultimte function of the Remoterig system together with rdio sttions with detchble control pnels like Kenwood TS-40, Kenwood TM-D70, Kenwood TS-2000, Yesu FT-57, ICOM IC-700, IC-703, ICOM IC-70, IC-220 nd Alinco DX-SR. You simply replce the cble between the control pnel nd the rdio with the Remoterig system. You will get the sme feeling nd functionlity s with the originl setup. TWIN The twin solution for Elecrft K3 nd Yesus is the high end solution for the DX-er or contester who do not wnt to compromise in the selection of rdio. The Twin solution is bsed on the ide tht one locl rdio controls the remote rdio nd you get the feeling tht you hve the rdio t your control site. For the Elecrft K3-Twin solution there is lso specil K3 clled K3/0 vilble which is specilly designed to use s control s it hs no RF-prts. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 9 of 233

10 PC-bsed control The system lso works very well for more trditionl remote control from PC-bsed control softwre s like HmRdioDeLuxe. The Remoterig system solves the voice nd dt trnsmission but you need PC for the Control softwre itself in this setup. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 0 of 233

11 Step by step system setup Below follows recommendtion bout how to proceed when setting up the system.. Spend some time to red thru this user mnul to get fmilir with the product. 2. Apply 2V DC (good stbilized power) to both units. 3. Connect both units with CAT5 ptch cbles to the sme Ethernet switch or router s your PC which you will use to setup the system is connected. 4. Downlod the Microbit Setup Mnger nd the ltest firmwre from to your PC. Follow the instructions bout how to instll the Microbit Setup Mnger (see chpter Configurtion with Microbit Setup Mnger). 5. Find out how your network is configured nd configure the RRC to fit into your network (see chpter Initil IP Setup) with the Microbit Setup Mnger. This hs to be done with both units.. Check the instlled firmwre version. If the one you downloded from Remoterig is newer, updte the units with the new firmwre. Alwys updte both units to the sme version (see chpter FW/HW bout how to updte). 7. When you hve configured the units to fit into your network, Strt your Web browser nd connect to the units one by one by entering their resp. IP-ddress. If you get in contct with their internl web server everything is OK.. Disconnect ll cbles from the units nd open the housings (see chpter Strppings nd jumpers) nd mke the hrdwre strpping ccording to the instruction which is provided in the chpter for your rdio in the end of this Users mnul. Check the red jumpers with ohm meter to verify tht they re not broken before ssembling the housings gin. 9. Mke the bsic softwre configurtion for your system which is described in the chpter for your rdio in the end of this Users mnul. 0. Prepre the cbles needed for your rdio sttion nd/or PC ccording to the cble drwings provided in the chpter for your rdio in the end of this Users mnul. Double check your home mde cbles with n ohm meter before connecting them to the RRC nd the rdio to prevent hrm of ny equipment. Microbit do not tke ny responsibility of dmged RRC-units or rdio equipment.. After prepring the cbles connect them to the RRC-units nd the rdio equipment. Connect the power to ll equipment. Check with your web browser gin tht you re in contct with both RRC-units. 2. Now try to estblish the connection between the Control-RRC nd the Rdio-RRC. If you use rdio with detched control pnel it s done when you press the ordinry power on button. If you re using PC-t the control end you need to browse to the sttus pge in the Control-RRC nd connect by clicking on the Connect button on. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

12 3. When the connection is estblished, test the functionlity. Check tht you cn her the receiver udio, check tht PTT is working nd microphone level is OK to be sure tht the strppings re OK. 4. When this bsic functionlity re OK you cn go further connecting cbles for CW, rotor control, PA-control etc. Prepre ll functions tht you need nd test them before moving the RRC:s prt to different loctions, everything gets much more complicted to test when trvelling is needed. 5. When it s time to move the RRC:s prt you need to gther some informtion bout how the network t the remote site is configured. The first thing is to determine if your Internet Service Provider (ISP) re providing you with fixed or dynmic IP-ddress. Fixed IP:s re rre so you probbly hve dynmic IP-ddress if you re not pying extr for fixed one. A dynmic IP is no problem but you need to use dynmic DNS service. You cn use Remoterigs free dynmic DNS service or DynDNS ccount. New DynDNS ccount is no longer free. For detiled informtion bout Dynmic DNS services see the Dynmic DNS chpters under Configurtion with WEB-Interfce.. After moving the RRC-prt you need to connect PC to the locl network t the remote site where the Rdio-RRC should be connected nd find out how the network is configured (see chpter Initil IP Setup). You hve to set up the new IP, Netmsk nd Gtewy. When it s done use your web browser to connect to the Rdio-RRC:s internl web server nd configure the DNS IP. 7. Configure the Rdio-RRC:s Dynmic DNS settings (see chpter Dynmic DNS Setting).. Now it s time to configure your remote router. We recommend tht you first of enble the remote configuring of your router, you my need it lter. After tht s done configure DMZ or port forwrding (see chpter Network nd Firewlls). When this is done your remote Rdio-RRC should be rechble over the Internet. 9. When bck t the Control QTH try to browse to the Dynmic DNS ddress (Own host nme) you hve setup t the Rdio-RRC. You should get in contct with the Rdio-RRC internl web server exctly s it ws locl. 20. The only setting which need to be chnged in the Control-RRC is the SIP-contct t the Rdio settings pge. The SIP-contct should be chnged to the Dynmic DNS Own host nme you hve setup in the Rdio-RRC or to the fixed IP of the Rdio QTH if you hve one. Then everything should work remotely. Enjoy the remote controlling. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

13 Hrdwre Front PWR LED Green light is indicting norml sttus. When the green LED is flshing slow the unit is trying to connect to the Ethernet, normlly it only tkes few seconds. If the LED do not end flshing it's probbly something wrong with the network connection or network setup. A fst flshing power LED indicte tht the unit is powered from USB (see USB below). USB The USB-interfce is used to initilly set up the IP prmeters. It cn lso be used for downloding new softwre (cn lso be done vi the WEB-interfce). At the Control-RRC it cn lso be used for CAT control, PTT, RTTY or CW control vi the RTS nd DTR signls in the virtul COM-port delivered by the RRC USB device. From Version the RRC cn be powered vi the USB to mke it esier to updte the Firmwre. Note tht the RRC need to be connected to 2V DC for norml opertion. When the unit is powered from the USB the green power LED will flsh fst. COM COM cn in specil cses be used to set prmeters nd check sttuses if USB or WEB cnnot be used. The COM port cn lso be used for ex. rottor control s it cn be configured s trnsprent seril port between the RRC:s. RS-232 Pin no RS-232 Interfce (9-pol D-sub femle) 2 TXD (Out) B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 3 of 233

14 3 RXD (in) 4 5 GND 7 CTS (In) RTS (Out) 9 AUX/MIC The AUC/MIC connector (RJ-45) is used for microphone connection or for connection of the rdio control pnel (IC-703/70, DX-SR). Inside the RRC behind the connector is set of strps with cn be used to decide how the connector should be configured depending on rdio or microphone. The red nd yellow LED:s re indicting SIP-sttus: LED LED Red LED Yellow Off Incoming udio strem OK SIP disconnected Flshing - SIP connection filed On Incoming udio strem fil SIP connection OK Pin no AUX (RJ45) depends on the inside strps 2 depends on the inside strps 3 depends on the inside strps 4 depends on the inside strps 5 depends on the inside strps depends on the inside strps 7 depends on the inside strps depends on the inside strps TTL Control-RRC The TTL connector on Control-RRC (RJ-2) is used primry for connection of the rdio control pnel (TS-40, RC-2000 nd IC-E220) nd in other cses where you need to connect vi TTL level (5V) port. The connector is configured so stright cble cn be used to TS-40 nd RC-2000 control pnel. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 4 of 233

15 Pin no AUX (RJ45) AF output, Speker 2W/ ohm 5 TDO input, dt from pnel to rdio (TTL) 4 RDO output, dt from rdio to pnel (TTL) 3 GND 2 V output, lwys ctive GND TTL Rdio-RRC The TTL connector on Rdio-RRC (RJ-2) is used for connection of the cble which is normlly connected between the control pnel nd the rdio (TS-40, RC-2000, nd IC-220). It's lso used for CAT control of rdios with 5V.s inputs e.g. ll ICOM with 3.5mm C-IV connector nd FT-x7 with the mini DIN-connector. The connector is configured so stright cble cn be used to TS-40 control pnel nd to RC Pin no AUX (RJ45) AF Input (TS-40) 5 TDO input, dt to rdio (TTL) 4 RDO output, dt to rdio (TTL) 3 GND 2 V output, lwys ctive GND SP Control-RRC At the Control-RRC the connector is used s speker output. It's connected in prllel with the udio output pins in the MIC/AUX nd TTL connectors. The connector is stndrd 3.5 mm jck for mini stereo plug nd there is no switch in the connector. The speker output power is 2W t ohm. In the dul RX (stereo) version there re signls from both the Min- RX nd Sub-RX vilble in the SP-connector. There is only Lf power mplifier on the Min RX signl so I recommend tht you set jumper JMP-4 in the Hedset position nd use hedset B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 5 of 233

16 or Stereo spekers with built in lf-power mplifier if you use Dul Receiver system. PC-type spekers re very well suited for this. Sub Receiver (*) Min receiver GND (*) Sub receiver, only vilble in RRC-25MkIIs version SP Rdio-RRC At the Rdio-RRC the speker connector is n input for the speker signls from the rdio. The Dul-Rx version hs inputs for both the Min-Rx nd Sub-RX. The Min-Rx input is connected in prllel with the input pins in the MIC/AUX nd TTL connector. The inputs hs resistive lods of 50 ohms. The connector is stndrd 3.5 mm jck for mini stereo plug nd there is no switch in the connector. Sub Receiver (*) Min receiver GND (*) Sub receiver, only vilble in RRC-25MkIIs version CW Control-RRC The CW knob is used for djusting the CW-speed of the built in CW-keyer. The CW Speed djustment is lso connected to the WinKeyer emultor. There is no knob on the Rdio-RRC. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

17 Bck COM2 Control-RRC COM2 is used to connect to PC COM port (RS-232). It hs femle connector which mkes it possible to use stright cble between RRC nd PC. The communiction prmeter is set vi the web interfce. RS-232 Pin no RS-232 Interfce for PC connection (9-pol D-sub femle) 2 RXD (out) to PC RXD 3 TXD (in) from PC TXD 4 5 GND 7 RTS - connected to JMP-3 CTS - connected to JMP-3 9 COM2 Rdio-RRC COM2 is used to connect to Rdio with RS-232 port. It hs mle connector, which mkes it possible to use stright cble between RRC nd the rdio. The communiction prmeter is set vi the web interfce. RS-232 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 7 of 233

18 Pin no RS-232 Interfce for Rdio connection (9-pol D-sub mle) 2 RXD (in) to pc RXD 3 TXD (out) from pc TXD 4 5 GND 7 RTS - connected to JMP-3 (*) CTS - connected to JMP-3 (*) 9 (*) Both Kenwood nd Yesu trnsceivers need the RTS nd CTS pins to be strpped together. JMP-3 inside the box cn be used to strp them if you wnt to use stndrd fully connected cble. PAD Control-RRC At the Control-RRC the input is used to connect CW-pddle. The input is for stndrd 3.5 mm stereo plug. Normlly the left pddle is connected to the tip nd the right pddle to the ring. Common is connected to the inner ring nd ground. Note tht the CW-Keyer function must be enbled to ctivte this function. PAD Rdio-RRC At the Rdio-RRC the output is used to connect the output signl from the CW-keyer to the rdio stright KEY input. The output is for stndrd 3.5 mm stereo plug. A stndrd cble with 3.5 mm connector in both ends cn often be used. Note tht the OUT mode or OUT2 mode must be set to Keyer to ctivte this function. PWR The RRC is powered vi the PWR connector (2./5.5 mm) with 0- VDC. Rdio Control-RRC (2 VDC) Rdio-RRC (2 VDC) IC-70 up to 00mA, depending on mx 0 ma (0mA 0Mbit) bck lighter nd udio volume TS-40 up to 500mA, depending on mx 0 ma (0mA 0Mbit) udio volume RS-232 up to 400mA, depending on udio volume mx 0 ma (0mA 0Mbit) B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

19 2V DC Pin no PWR VDC (centre) - GND RESET A short press on the reset switch will reboot the unit. By pressing nd keep the button pressed for 20 sec the unit reset to fctory defult settings with the following network settings: Control-RRC IP-ddress: Rdio-RRC IP-ddress: Netmsk: Gtewy: DNS: I/O In the I/O connector is 3(2) inputs nd 3 outputs, V nd GND vilble (see below). The connector is used for trnsferring signls from one RRC to the other. If the CW-keyer function is not used the connector cn be used for whtever controls signls needed in both directions. The output trnsistor cn sink mx 200mA so instll n externl rely if it's not strong enough. Pin no I/O (RJ45) IN, ctive low (CW-Keyer right-pddle) 2 IN2, ctive low (CW-Keyer left-pddle) 3 OUT2, open collector (prllell with PAD Tip t Rdio-RRC) 4 IN0, ctive low (only vilble t Control-RRC) 5 OUT0 open collector OUT open collector (prllell with PAD Ring t Rdio-RRC) 7 V OUT (mx 00mA) GND B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 9 of 233

20 ETHERNET The unit cn be connected to both 0 nd 00 Mbit/s Ethernet bsed TCP/IP network. The RRC cn be configured for different connection types for Ethernet port, Auto, 0HDX, 0FDX, 00HDX, 00FDX nd Auto-with-preferred-0FDX. Defult is Auto-with-preferred-0FDX which works best in most cses. Pin no Ethernet (RJ45) Out [+] 2 Out [-] 3 In [+] 4 5 In [-] 7 LINK Green LED indictes link OK flshing LED indictes trffic ACT Yellow LED indictes speed = 00Mbit/s (off = 0MBits/s) B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 20 of 233

21 Strpping nd jumpers Before connecting the RRC to your rdio you need to put some strps in plce depending on your rdio. Down below follows instructions of how to disssembly the RRC nd pictures showing where to find the different strps. : Strt with removing the screws holding the D-sub on the rer mrked COM2. The tool should be 5 mm (3/"). 2: Open the box by pressing the D-sub until you cn get your fingers behind the edge of the lid nd cn slide the housing prt. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

22 3: Behind the AUX/MIC connector there is strpping re which looks like n IC-socket. There re two rows with 9 holes. The row next to the AUX/MIC connector is connected to the connector. The strpping is done by connecting the red strp wires, supplied with the RRC, between the holes ccording to the description for the rdio (see rdio chpter). Normlly the sme strpping should be done in both Control-RRC nd Rdio-RRC. (The picture shows the strpping for IC-70). Attention! The strpping wires should NOT be soldered. Just push them into the socket. The mechnicl friction is enough to get connection. Socket Pin : Control-RRC only: JMP- is plced behind the TTL connector. With the strp in plce DC voltge is feed to the microphone element. All ICOM microphones should be DC-feed. Dynmic microphones like the ones used by Kenwood should not be DC-feed. HEIL microphones should not be DC-feed either. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 22 of 233

23 5: Control-RRC only: JMP-2 is plced ner the bck of the RRC next to the RESET button. JMP-2 is used to select if the DC-power to the front pnels should be or 9 V. With the strp in plce it will be V, which fits ll ICOM rdios. Without the strp the voltge will be 9V, which fits Kenwood TS-40 nd RC-2000 pnels tht need 9V for the bck-lighter. : JMP-3 is plced next to the rer D-sub COM2. JMP-3 is used to connect RTS nd CTS together (pin 7 nd ) in COM2. Most of the Yesu nd Kenwood rdios with RS-232 port need to hve them tied together. This is convenient if you wnt to use prefbricted fully connected cble. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 23 of 233

24 7: Control-RRC Only: JMP-4 is plced behind the CW-pot, nd is vilble only in the Control- RRC nd re only present in the RRC-25MkIIs up to Hrdwre version 5. JMP-4 is used to select between Speker level or Hedset level for the Min-Rx output. The Sub-Rx is lwys Hedset level. From hrdwre version it s lwys speker level from both RX. : JMP-5 is plced behind the TLL connector nd is only present in the RRC-25MkIIs from hrdwre version 7. JMP-5 is used to decide if pin in the TTL connector should be grounded or not. It should be grounded (in plce) for ll Rdios but Yesu FT-57 nd ICOM ID-E-0 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 24 of 233

25 9: When you re done you cn slide the lid on the bottom prt nd put bck the screws. Be creful the threds do not stnd to much force. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 25 of 233

26 Configurtion with Microbit Setup Mnger The initil settings of the network prmeters re esiest done with the Microbit Setup Mnger. The Setup Mnger is softwre which runs under Windows on PC nd connects to the RRC vi USB (n USB cble is supplied with the RRC). The Setup Mnger cn be used for: IP Settings nd verifiction o IP-ddress o Netmsk o Gtewy o DNS o DHCP Firmwre upgrde o Appliction o Bootloder Chnging profile Scnning for WiFi networks nd WiFi setup. Strt with downloding the Microbit Setup Mnger from the homepge Instll the Microbit Setup Mnger by following the instructions which shows up. If you hve n old version of Windows P where Netfrmework 2.0 is not instlled, you hve to instll Netfrmework from Microsoft before instlling the Setup Mnger. When you hve finished the instlltion new shortcut to the Setup Mnger will show up on the desktop. Click on the icon to strt Setup Mnger Connect your RRC to 2V nd connect the USB-cble between your computer nd the USB jck on the front of the RRC. Windows will utomticlly instll the necessry drivers. When it's done the text in the bottom field will chnge from "RRC not connected" to "RRCconnected" which is n indiction tht you re in connection with the unit. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

27 FW/HW version When you connect the RRC the version of the firmwre nd Bootloder will show up in the upper window. The hrdwre versions is lso shown. Go to the pge nd under downlods you cn find the ltest firmwre. If there is newer firmwre vilble downlod it to your desktop unzip it nd chnge to the "FW-updte" tb. FW updte B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 27 of 233

28 Click on the "Select file" button nd browse to the file with the new firmwre, it should be something like RRC-25-CRC_v2.42_ bin depending on the version nd relese dte. When you hve selected the file click on the "Updte" button nd the updte process will strt, the text in the bottom field will chnge to "Updting firmwre". Attention -- Do not interrupt the updte process in ny wy! After bout minute the updte is finished nd the RRC will restrt. When the text "RRCconnected" shows up gin in the lower field of the Microbit Setup Mnger, you cn chnge to the "FW/HW" tb nd check softwre version. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

29 Setup The setup tb re used to setup the IP ddress nd/or select the profile (from v2.44). More info bout the IP setup see Initil IP-setup. A new window wills pop-up with the bsic IP settings. Chnge the settings so they fit into your locl network nd press the "Sve" button to sve the new settings. The RRC will restrt gin nd when the text "RRC-connected" shows up gin in the lower field of the Setup Mnger, you cn click on the "Setup" button gin to verify the chnges. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 29 of 233

30 Net info Click on the Get button to red the IP setting currently in use by the RRC. WiFi nd Seril Port tbs The Wifi tb is described in the WiFi Chpter. The Seril port tb is not used for the RRC- 25MkII it s used for other products. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 30 of 233

31 Initil IP setup The defult Ip settings from the fctory is (Control-RRC) nd (Rdio-RRC). The net msk is nd the gtewy To be ble to contct the RRC-units vi the network you must configure the units to fit into your home network. You cn check your network configurtion from your PC. On the strt menu select Run. In the Run dilog box enter cmd. You will get DOS-window. At the DOS-promt enter ipconfig. Then you will get the needed informtion: Your PC IP ddress in this exmple is this mens tht the IP of the RRC:s must hve IP:s in the re to B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 3 of 233

32 The Netmsk is the Netmsk in the RRC:s should be the sme The Defult gtewy is the Gtewy in the RRC:s should be the sme In this cse ll the defult IP setting will be OK. In n other network, this is the result of the ipconfig commnd. Your PC IP ddress in this exmple is this mens tht the IP of the RRC:s must hve IP:s in the re to The Netmsk is this the Netmsk in the RRC:S should be the sme The Defult gtewy is the Gtewy nd in the RRC:S should be the sme The DNS should in lmost ll sitution be the sme s Defult gtewy. In this cse you must chnge the IP:s of the RRC. I recommend to use nd Use the Microbit Setup Mnger to chnge the IP settings. Select the Setup tb click on the Get Setup button nd enter the IP ddresses in the Setup info dilog box. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 32 of 233

33 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 33 of 233

34 Configurtion with WEB-interfce Before you cn use your RRC-25MkII you must configure both the hrdwre (strpping) nd the softwre settings. The units will hve the defult IP ddresses (Control-RRC) nd (Rdio-RRC). The net msk is The configurtion is esiest done vi the web interfce. Be wre of tht your PC must be in the sme net e.g. hving n IP-number between nd nd not be the sme s the RRC. If the defult IP-ddresses of the RRC not fit your network plese use the PC-progrm Microbit Setup Mnger to chnge the IP-ddresses vi USB. It's convenient to use DHCP t the Control-RRC but wit to ctive DHCP until everything is setup nd working. Select setup pge from the links on the left side nd edit the prmeters. After ech setup pges is finished press Submit to temporry store the new settings. When you do tht new red Apply chnges button ppers on the pges. You cn now chnge prmeters on other pges but the new settings will not tke effect until you press Apply chnges. When you do tht the unit will reboot nd strt up with the new settings. If you chnge your mind fter clicking on submit you cn click on Restrt device on the left to restrt the device without chnging ny settings. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 34 of 233

35 Info The info pge shows some sttic informtion bout the RRC s firmwre revision etc. nd lso the bsic IP-configurtion. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 35 of 233

36 Sttus On the sttus pge you cn check some prmeters which cn be useful when debugging etc. But the most importnt is tht here is the "Connect" nd "Disconnect" button used to connect or disconnect the Internet connection between the two RRC in some modes. If the system is setup to be used with Control pnels or Twins then there is no Connect/disconnect buttons, the connection is controlled by the power on switch on the control pnel. In some modes there re disconnect button on the Rdio-RRC sttus pge which in multi user system cn be used to disconnect user who hve forgot to do it. When connecting you will see how the SIP-sttus is chnged to "Connected/Trnsferring" if everything is OK. Here is lso shown how your NAT-router hs mpped the ports nd the momentry sttus of the inputs nd outputs nd some other things. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 3 of 233

37 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 37 of 233

38 Profiles The profile menu is used to store nd lod settings profiles. This could be convenient if you chnge settings often. But NO settings re needed here if you do not use it, so leve this pge to lter if it s your initil setup of the RRC:s. You cn use up to five profiles nd you cn give them describing nmes. The first time you ctivte nother profile thn the defult profile the defult profile will be copied to the other profiles. When you sve settings in the norml wy with the red pply settings button the dt will be sved in the profile which is ctive for the moment. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 3 of 233

39 To chnge profile just select Active profile to the profile you wnt to chnge to, nd press submit. The new profile will then be loded but will not be used before restrt so you cn check ll settings nd the restrt to mke the new profile ctive. Profiles cn lso be chnged from the Setup Mnger which cn be useful if you connected it to different networks. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 39 of 233

40 IP Settings The IP Settings menu is used to setup the initil IP prmeters needed for the unit to connect to the IP network. Down below the settings re described more in detils. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 40 of 233

41 Prmeter Unit ID (Bnner) DHCP IP Netmsk Gtewy Dns server Extern IP/Host Eth-type Setting Text, whtever you wnt, tht will be shown t the top of the web-pge (within brckets). Used to identify different RRC. empty (defult) text Select between fixed IP ddress nd DHCP. DHCP cn be prcticl for the Control-RRC but fixed IP ddress is preferred in Rdio-RRC. No (defult) Yes IP-ddress (only when fixed IP-ddress is used) (defult Control-RRC) (defult Rdio-RRC) nnn.nnn.nnn.nnn Net msk (only when fixed IP-ddress is used) (defult) nnn.nnn.nnn.nnn Gtewy (only when fixed IP-ddress is used) (defult) nnn.nnn.nnn.nnn DNS-ddress (only when fixed IP-ddress is used) (defult) nnn.nnn.nnn.nnn Fixed externl IP-ddress of your NAT-router. Should NOT be used in norml instlltions. empty (defult) nnn.nnn.nnn.nnn Type of Ethernet connection: Auto Auto, prefer 0 Mbit (defult) 0HDX* 0FDX* 00HDX* 00FDX* Auto prefer 0 Mbit is defult s more speed is not needed nd the emissions from 0 Mbit LAN is much less thn from 00 Mbit LAN (*) If you use fixed settings you must hve mnged switch where you cn set the sme setting. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 4 of 233

42 IP-interfce Web pge user Web pge pwd Normlly the RRC connects vi the Ethernet interfce if it s vilble, nd s second choice vi the WiFi. If you set it to Ethernet you cn force the RRC not to connect vi WiFi even if the Ethernet is not vilble for the moment. Auto, prefer Ethernet (defult) Ethernet Enble pssword protection for the web pges nd lso the telnet connection by entering usernme (this field) nd pssword (next field). If this field is empty the RRC will not sk for pssword. Some of the pges re still ccessible but no editing is possible. empty (defult) usernme Pssword for the web pges nd telnet connection. The pssword re shown s **** to view it click on the show button empty (defult) pssword B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 42 of 233

43 Rdio Settings The Rdio settings re used to setup the RRC to ct together with different rdios. The settings must be done in both Control-RRC nd Rdio-RRC nd the prmeters re prtly different for the both RRC. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 43 of 233

44 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 44 of 233

45 Prmeter Progrm mode Sip pssword Sip contct Auto connect Setting Select the progrm mode depending on connected rdio: 0 = Trnsprent (for repeter links etc.) = ICOM CI-V (generic) 2 = IC70 (with detched control pnel) 3 = FT-x7, FT-000 (generic) 4 = Kenwood, Yesu, Elecrft 5 = TS40/TM-D70 (with detched control pnel) = (*) 7 = IC-R2500/IC-2725(with detched control pnel) = TS-2000/TM-D700 (TS-2000 with RC-2000) 9 = IC-220 (with detched control pnel) 0 = Yesu FT-950/FT-2K/FT-5K/FT-9K- Twin = Trnsprent, 4-wire (for repeter links etc.) 2 = DX-SR (with detched control pnel) 3 = ID-E0(with detched control pnel) 4 = K3 twin 5 = Yesu FT-57 (with detched control pnel) = Yesu FT-00 (with detched control pnel) 7 = Yseu FTM-350 (with detched control pnel) (*) These selections re only possible in specil editions of the RRC. Protect your remote rig nd should be sme in both ends. Normlly shown s **** click on the show button to view the pssword. (defult: no pssword) Control-RRC: Sets the fixed IP ddress or the Dynmic DNS own host nme to the Rdio-RRC Control-RRC: When enbled the Control-RRC will connect to Rdio-RRC immeditely fter power up in progrm mode 0,, 3 nd 4. No (defult) Yes B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 45 of 233

46 Audio qulity Sets the udio qulity depending on vilble bndwidth. Smple rte must be sme in both RRC but coding cn be different (more informtion cn be found in ppendix-a Audio coding): 0 = A-lw khz = Liner 2 bits khz 2 = Liner bits khz (defult) 3 = A-lw 2 khz 4 = Liner 2 bits 2 khz 5 = Liner bits 2 khz = A-lw khz 7 = Liner 2 bits khz = Liner bits khz 9 = A-lw 24 khz 0 = Liner 2 bits 24 khz = Liner bits 24 khz 2 = IMA ADPCM 4 bits khz 2 = IMA ADPCM 4 bits khz Audio Dul-RX Sets if LF from the Sub-RX should be sent s n seprte udio chnnel. Be wre of tht this doubles the need of Bndwidth. (Only vilble in the (s) version.) Codec out gin Sets the ttenution for the udio output, in 255 steps nd 0.5 db per step. Should lwys be set to = no ttenution (defult) 254 = -0.5 db 253 = -.0 db 0 = mx ttenution Codec inp gin Sets the gin for the udio input in 3 steps nd 0.75 db per step. Should be t Control-RRC for high level electret microphones nd should lwys be 0 t Rdio-RRC. 0 = defult Rdio-RRC = defult Control-RRC 3 = mx vlue B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 4 of 233

47 Codec inp HPF Hz Codec inp premp Codec inp ttenution COM0 budrte COM0 dt bits COM0 stop bits COM0 prity Sets the low cut frequency for the udio pssbnd [Hz]: (defult) The upper cut frequency is set utomticlly depending on the smpling rte. Control-RRC: Enbles +20 db pre-mplifier for the udio input t the Control-RRC: No Yes (defult) Rdio-RRC: Enbles -20 db ttenutor to the speker input t the Rdio-RRC: No (defult) Yes Set COM0 budrte for the rdio communiction [bps]: (IC-R2500,IC-2725) 9200 (IC703/70) 3400 (IC220,DX-SR,ID-E0) 4000 (FTM-350) 5700 (TS40, TS2000) 4000 (FT-57, FT-00) Set COM0 dt bits: 5 7 (defult) Set COM0 stop bits: (defult) 2 Set COM0 prity: 0 = Off (defult) = Odd 2 = Even 3 = Forced- 4 = Forced-0 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 47 of 233

48 COM0 Progrm mode 3 chr timeout Use USB Com Port s COM0 The chr timeout cn be progrmmed. The defult timeout should be 2 nd works for ll rdios except FT-000 in 400 bud which need it to be set to 0. 2 = defult 0 = FT-000 in 400 bud COM0 cn be connected to the USB interfce insted of the norml seril interfce. When instlling Microbit Setup mnger virtul Com port clled Microbit RRC Virtul Comport (COMX) is instlled. Tht s the one you should connect to when using HRD or other softwres. Yes or No (defult = No). B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 4 of 233

49 Seril Settings The seril ports COM nd COM2 cn be used s trnsprent seril chnnel between Control-RRC nd Rdio-RRC over Internet. The COM-ports cn be used for CAT control, rottor control etc. COM is lwys free to be used with the drwbck tht you cnnot use COM for configurtion. COM2 is used for the rdio control in some of the progrm modes nd cn then not be used s trnsprent seril chnnel. There is lso COM3 which is only vilble vi USB nd only for WinKey nd RTTY. Rdio settings / Progrm mode COM free chnnel COM2 free chnnel 0 - Trnsprent yes yes - ICOM CI-V yes no 2 IC-700,IC-70,IC-703 yes yes 3 FT-x7, FT-000x yes no 4 Yesu, Kenwood, Elecrft yes no 5 TS40/TM-D70 yes yes (*) yes yes 7 IC-R2500/IC-2725(*) yes yes TS2000/TM-D700 yes yes 9 IC-220 yes yes 0 Yesu FT-450/FT-950/FT- yes no 2000/FT-5000/FT-9000 Twin Trnsprent, 2/4-wire(*) yes yes 2 DX-SR yes yes 3 ID-E0 (*) yes yes 4 Elecrft K3-Twin yes no 5 Yesu FT-57 yes yes FT-00 yes yes 7 FTM-350 yes yes COM nd COM2 mode cn be configured differently depending on wht they will be used for. The sme settings must be done in both Control-RRC nd Rdio-RRC. (*) = Need specil hrdwre B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 49 of 233

50 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 50 of 233

51 Prmeter COM mode Setting Select mode for COM-to-COM trnsprent trnsfer of seril dt between two opposite RRC. The setting defines the event tht triggers the dt trnsfer over Internet. Inctive (defult) Mode = Chr-by-chr. A dt pcket is send for ech chr, needs lot of bndwidth. Mode 2 = ICOM CI-V. Used for CI-V control of IC-703/70 t the sme time s you use the control pnel. Mode 3 = Chr-timeout. A dt pcket is sent when there is pre-defined puse between two received chr. Mode 4 = Kenwood, Yesu, Elecrft. Used for CAT control of TS-40 or TS-2000 t the sme time s you use the control pnel. Mode 5 = User-def-termintor. Used if you wnt to define the termintor chr by yourself (see below). Should be ctivted together with Mode-7 in Rdio-RRC to combine dt from COM with the other ports described bove. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 5 of 233

52 COM budrte COM dtbits Mode = CAT to COM2 locl (Control-RRC) mkes it possible to connect for exmple logger PC which needs to spek to the Control rdio to COM t the Rdio-RRC. The IP-dt from rdio side COM2 nd this locl COM will be intelligent mixed (in sequence) before sent to locl COM2. Dt from locl COM2 goes to both locl COM nd to the rdio side COM2 vi IP. This function is only for the Yesu Twin configurtion only. Mode = CAT to COM2 locl (Rdio-RRC) mkes it possible to connect other hrdwre which needs to spek to the rdio vi COM t the Rdio-RRC. The IP-dt from control side COM2 nd locl COM will be intelligent mixed (in sequence) before sent to locl COM2. Dt from locl COM2 goes to both locl COM nd to the control side COM2 vi IP. Cn be used for MicroHm, the Web- Switch, Power Amplifier etc. This function is for Yesu, Kenwood nd Elecrft only. Mode 7 = CAT to COM2 locl & remote (Rdio-RRC) Sme function s bove but it lso combines dt sent from COM in Control-RRC with dt from the locl COM nd Control- RRC COM2. (Remember tht this function doubles the dt mount sent over the Internet). Mode 7 = CAT to COM2 remote (Control-RRC) Is used in combintion with mode 7 t the Rdio-RRC. Mode = The WinKeyer emultor is ctivted, nd dt received from COM re sent s CW from the Rdio-RRC in prllel with the ordinry keyer. Set COM budrte [bps]: (defult) Set COM dt bits: 5 7 (defult) B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 52 of 233

53 COM stop bits COM prity COM cts/rts COM termintor Use USB Com Port s COM Set COM stop bits: (defult) 2 Set COM prity: 0 = Off (defult) = Odd 2 = Even 3 = Forced- 4 = Forced-0 Enble the trnsfer of CTS input to RTS output of other RRC. 0 = No (defult) = Yes Defines the termintor chrcter used in COM- mode=5 (user-def-termintor). Chrcter should be in HEX-formt. 00 (defult) COM cn be connected to the USB interfce insted of the RS-232 interfce if your PC do not hve trditionl com ports. When instlling Microbit Setup mnger virtul Com port clled Microbit RRC Virtul Comport (COMX) is instlled. Tht s the one you should connect to when using HRD or other softwres. Yes or No (defult = No). B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 53 of 233

54 COM2 mode COM2 dtbits COM2 stop bits COM2 prity COM2 termintor Use USB Com Port s COM2 COM3 mode (USB-COMFSK) Only vilble in the Control-RRC Select mode for COM2-to-COM2 trnsprent trnsfer of seril dt between two opposite RRC. The setting defines the event tht triggers the dt trnsfer over Internet. Inctive (defult) Logicl prllel with COM0. = Is used for level converting for CI-V nd FT-x7. The settings from Rdio settings re used. Mode = Chr-by-chr. A dt pcket is send for ech chr, needs lot of bndwidth. Mode 2 = ICOM CI-V. Used for CI-V control of IC- 703/70 t the sme time s you use the control pnel. Mode 3 = Chr-timeout. A dt pcket is sent when there is pre-defined puse between two received chr. Mode 4 = Kenwood, Yesu, Elecrft. Used for CAT control of TS-40 or TS-2000 t the sme time s you use the control pnel. Mode 5 = User-def-termintor. Used if you wnt to define the termintor chr by yourself (see below). Mode = The WinKeyer emultor is ctivted, nd dt received from COM re sent s CW from the Rdio-RRC in prllel with the ordinry keyer. See COM See COM See COM See COM COM2 cn be connected to the USB interfce insted of the RS-232 interfce if your PC do not hve trditionl com ports. When instlling Microbit Setup mnger virtul Com port clled Microbit RRC Virtul Comport (COMX) is instlled. Tht s the one you should connect to when using HRD or other softwres. Yes or No (defult = No). COM3 is vilble only vi USB. It s shown s COMFSK in Widows Device mnger. In mode- the WinKeyer emultor is ctivted, nd dt received from the USB port re sent s CW from the Rdio- RRC in prllel with the ordinry keyer. In mode-0 received dt from the USB port RTTY re sent by the Rdio-RRC vi one of the (selectble) outputs. Inctive (defult) Mode- WinKeyer Mode-0 Budot RTTY B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 54 of 233

55 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 55 of 233

56 Advnced settings Under dvnced settings it is possible to chnge the defult port numbers used by the RRC. It cn be necessry if there re more thn one RRC on your LAN. In erlier versions we used port 500 for SIP but it s often reserved for IP-telephony tody so we hve chnged defult ports. You relly need to know wht you re doing when you chnge port numbers especilly on the Rdio-RRC so tht you don't disconnect yourself. Chnge web nd telnet port number ONLY if you hve to due to other services or more thn one RRC on your LAN. If you lose the connection cr ride might be the next thing you do. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 5 of 233

57 Prmeter UDP cmd port UDP udio port SIP port Setting Port number used for the Commnd chnnel (defult) Port number used for the udio chnnel 300 (defult) Port number used for the SIP session (defult) B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 57 of 233

58 Web server port Telnet server port Rx jitter buffer size Rx jitter dely Audio pcket size (ms) RTP Tx Mode Debug level Disble Audio tones (Control-RRC only). Port number used for the internl http web server. 0 (defult) Port number used for the internl telnet server. 23 (defult) Set the mximum number of udio pckets from the received udio strem tht is buffered. Dicttes mximum plybck dely. Higher vlues result in better tolernce ginst bd Internet connections. Note tht this vlue must be lrger thn the jitter dely. 4 (defult) Set the number of udio pckets received nd buffered from the udio strem before beginning plybck. Dicttes minimum plybck dely. Smll vlues gives short delys, higher vlues result in better tolernce ginst bd Internet connections but the dely will increse. Note tht this vlue must be less thn the jitter buffer size. 3 (defult) Sets the mx size (length) of the udio pckets in ms. If you hve good Internet connection with lots of bndwidth or running both RRC:s under the sme LAN/WLAN it's possible to reduce the pcket size down to ms. Smller pckets mens decresed dely but incresed bndwidth. 20 (defult) Control-RRC: If VOX will be used switch on this function. It mens tht the udio strem is sent continuously from the Control-RRC to the Rdio-RRC. This cn be security problem for some user becuse the udio from the mic is sent to the Internet ll the time. Rdio-RRC: Some mobile (3G) networks hve dely before they open up for the udio strem which ends up in problems when relesing the PTT. This function often solves this problem. If you use Squelched rdio you cn set RTP tx mode to Squelched, the udio dt will then only be sent when the squelch is open to reduce cost if you py by Mb for exmple. Norml (defult) Continuous Squelch (Only rdio-rrc) Not used, nd should not be chnged. Off (defult) Low Medium High Mkes it possible to disble the Busy nd Error tones. No (defult) Yes B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 5 of 233

59 Audio tones-db [70-0] (Control-RRC only) IP identifiction (morse) (Control-RRC only) Full Duplex (Control-RRC only) Yesu pwr-on/off (Rdio-RRC only) PTT-off mute dely (Control-RRC only) IP Type-of-Service (dec) Elecrft dvnced UDP ntenn-switch port (Rdio-RRC only) UDP cmd min-dtsize You cn set the level of the different sttus tones generted by the RRC (defult) Mkes it possible to let the Control-RRC to send it s IP number in morse code, cn be useful when DHCP is used. No (defult) Yes Mkes it possible to use full duplex. Eg. the speker will not be muted when PTT is pressed. To use the function Continuous RTP Tx must be ctivted in the Rdio-RRC. No (defult) Yes Is used to switch on nd off Yesu FT- 450/950/2000/5000/9000rdios utomticlly on connect/disconnect when rdiomode 4 or 0 is used. No (defult) Yes Mkes it possible to mute chirps coming from Txmonitor udio when PTT is relesed (0 = defult) The RTP pckets cn be tgged for ToS ccording to RFC 79 to mke it possible to use QoS in networks which support QoS. The prmeter is entered in deciml. 0 (defult) Not in use Sets the port to which the Remoterig 0 x Antenn switch should connect to, Should mtch the settings in the ntenn switch. 300 (defult) In some very rre situtions routers/isp will not trnsfer very short UDP messges. In this situtions you cn set the min dt size of the messge. The messge is filled out with dummy dt (defult) B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 59 of 233

60 Dynmic DNS setting (only Rdio-RRC) The Rdio-RRC hs Dynmic DNS client to be used when the Internet Service Provider (ISP) uses dynmic IP ddresses (DHCP) insted of fixed IP ddress. DHCP is the most common for privte users. The RRC supports our own free Remoterig dynmic DNS service nd DynDNS which is not free for new users nymore. You cn choose to use one of them. The dvntge with using dynmic DNS service is tht you do not need to know the IP ddress to your remote router, you only need to remember the own host nme. The Rdio-RRC will utomticlly updte the DNS server when the IP chnges so you don t need to bother bout it. Remoterig dynmic dns service The Remoterig dynmic dns service only support equipment from Remoterig nd Microbit like the RRC-25 nd the WebSwitch 2H etc. The Remoterig dynmic dns service do not need ny registrtion it s utomticlly generted bsed on the seril number on the equipment. To ctivte the Remoterig dynmic dns client select ddns.remoterig.com from the drop down on the Dynmic DNS settings pge. Also select DNS check intervl, if your IP ddress chnge often you cn select low vlue, if it goes month between the chnges you cn select higher vlue. After tht click on Submit nd Apply chnges, the RRC will restrt. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 0 of 233

61 After the RRC hs restrted go bck to the Dynmic DNS settings pge. You will now see tht the settings Own hostnme, Usernme nd Pssword re utomticlly generted. The only importnt informtion is the Own hostnme, copy the whole row, this is the informtion you should put into the SIP contct box in the Control-RRC nd the web ddress you should use when remote configure the Rdio-RRC in the future. No more registrtion is needed. Remember tht DNS ddress like this is only for use when you connect over the internet, s long s you re operting on you own LAN use the IP ddress. When using ddns it s importnt tht the DNS settings re ok s they re needed for the RRC to be ble to updte the ddns. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

62 When you hve done the setup nd restrted the RRC, it will updte the Remoterig DDNS. You cn check the sttus of the updte t Enter the hostnme from your RRC in this exmple = hfd3dqw. If your RRC hs updted the DDNS you will see when nd wht current public IP the RRC hs reported. If it s not updted check the RRC-sttus pge nd check the DNS nd DDNS sttus. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

63 DynDNS dynmic dns service The Rdio-RRC lso supports the commercil dynmic DNS service DynDns. Erlier this ws free service, it s still free for old users but not for new. If your router hs DynDNS client you cn lso use tht one, nd do not ctivte more thn one DynDNS client t the sme LAN segment. DynDNS do not ccept multiple updtes from sme IP. The DynDNS client checks wht IP ddress your router hs got from the ISP nd sends the informtion to DynDNS:s DNS server. When using DynDNS you enter "Own host nme" insted of n IP ddress in the SIP contct setting in the Control-RRC nd you don't need to bother if the IP ddress t the Rdio-RRC chnges. You need to register n ccount t nd get domin nme. There re other providers of the sme service but RRC-25MkII only supports DynDNS or Remoterig ddns. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 3 of 233

64 Prmeter Dynmic DNS check intervl Dynmic DNS host nme Own host nme Usernme Pssword Setting Sets how often the externl IP ddress of your router should be checked, vlue in minutes: Off (Dynmic DNS client disbled) Sets which DNS service you will use ddns.remoterig.com (our own free service) members.dyndns.org (commercil service) Domin nme registered t DynDNS.com. Exmple: my-rdio-site.hm-rdio-op.net Dynmic DNS ccount usernme. Dynmic DNS ccount pssword. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 4 of 233

65 Keyer Settings (Control-RRC) A very powerful function for remote CW opertion is implemented in the RRC-25MkII. The system is ble to hndle delys nd jitter cused by Internet in unique wy. This function is lso dependent on the I/O configurtion, see IO settings. The Keyer lso hndles stright key CW generted from n old fshion stright keyer or computer. The RRC lso emulte WinKeyer to be ble to send CW from log progrm supporting WinKeyer. The WinKeyer emultor hs to be ssigned to COM, COM2 or COM3 (USB) see seril settings. Prmeter Enble Setting Enble the CW-keyer function. No = CW-keyer is off Yes = CW-keyer is on (defult) B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 5 of 233

66 Imbic Set the CW-keyer imbic mode. Old type, squeeze keyer Mode-A Mode-B (defult) Mode-B + uto-chr-spce Pddle reverse Set the reverse mode for the CW-pddle. No, left pddle dot & right pddle dsh (defult) Yes, left pddle dsh & right pddle dot Weight Time rtio between dsh nd dot = / 30 = 3.0/ (defult) Side tone hz Frequency for the side-tone in Hz. 0, = side-tone frequency in Hz 00 = 00 Hz (defult) 0 = No locl side tone is generted, cn be used to test how the CW sounds if you enble side tone in the rdio nd send with memory keyer or PC. Side tone -db Audio level for the side-tone in db = udio level in db 20 = -20 dbm (defult) Lf dely ms Mute (dely) time for udio from the rdio t Control-RRC fter dot/dsh commnd. Recommendtion - strt with sme vlue s the ping time = dely in milliseconds 0 = no dely (defult) Key dely ms Dely time before the keying of the rdio is executed t RRC- rdio = dely in milliseconds 50 = 50 ms dely (defult) Speed pot min wpm[5-99] Speed pot mx wpm[5-99] Sets the lower limit of the pot rnge 5-99 = 5-99 wpm 0 = 0 wpm (defult) Sets the upper limit of the pot rnge 5-99 = 5-99 wpm 0 = 40 wpm (defult) B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

67 Keyer Settings (Rdio-RRC) In the Rdio-RCC only one prmeter is vilble. PTT-ctivted by keyer is function tht is useful if you wnt the PTT input of the rdio to be ctivted when using the Remoterig keying function. The PPT is ctivted before the Key dely mening tht PA for exmple cn be ctivted x ms before the keying signl is ctivted to prevent hot switching. With the PTT til dely you cn decide how long the PTT will be kept ctive fter the lst CW chrcter is sent. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 7 of 233

68 Prmeter PTT ctivted by keyer PTT til dely ms [999] Setting Enble the PTT function. No = (defult) Yes = PTT is ctivted by the keyer Enble the PTT Til function 0 = No dely (defult) -999 = dely in ms. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

69 IO Settings The inputs nd outputs in both the Control-RRC nd Rdio-RRC re configurble to meet different needs. Control-RRC: Prmeter IN0 mode Setting Select the function for Input-0 (IN0) signl in the I/O connector. 0 = I/O, input sttus is trnsferred to Rdio-RRC (defult) = Keyer, stright key or externl keyer 2 = PTT, PTT-switch or foot-switch etc. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 9 of 233

70 OUT0 mode OUT mode OUT2 mode USB RTS s PTT USB DTR s CW Output 0 cn only be configured for one of two functions. I/O = Indicting tht SIP connection is up. Keyer = The output follows the Keyer output. OUT mode Output cn be configured for one of two functions. I/O = The output follows Input from the Rdio-RRC. Keyer = The output follows the Keyer output. Output 2 cn cn be configured for one oftwo functions. I/O = The output follows Input 2 from the Rdio-RRC. Keyer = The output follows the Keyer output. Select which of the USB virtul COM ports RTS signl which should be used s externl PTT. Useful when using Logging softwre, RTTY progrms etc. Disbled = (defult) COM0 = COM0 rts is used s PTT control COM = COM rts is used s PTT control COM2 = COM2 rts is used s PTT control Select which of the USB virtul COM ports DTR signl which should be used s CW key input. Useful when using Logging softwre, RTTY progrms etc. Disbled = (defult) COM0 = COM0 dtr is used s CW key input COM = COM dtr is used s CW key input COM2 = COM2 dtr is used s CW key input B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 70 of 233

71 Rdio-RRC: B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 7 of 233

72 Prmeter Setting OUT0 mode Select the function for output-0 (OUT0) signl the I/O connector. 0 = I/O, ctive when IN0 on Control-RRC is ctive (Control-RRC IN0-mode setting must be in stte I/O). (defult) = Keyer, output to the rdio stright key input 2 = PTT, used s externl PTT 3 = Connect, ctive when the SIP-connection is ctive 4 = On/Off, controlled by the ON/OFF button on this side (*) 5 = Keyer PTT, ctive when CW is send vi the keyer (cn be used to key PA). If you set key dely in the Control-RRC this output will be ctivte key dely ms before the ctul CW-keying is strted. = Budot/45 used s output for RTTY bud. RTTY input vi USB virtul com port t Control-RRC. Connect PC softwre to the virtul com nmed FSK COM. 7 = Budot/45 (inv) sme s bove but the RTTY key signl is inverted. OUT mode Select the function for output- (OUT) signl the I/O connector (or tip in the PAD-jck). 0 = I/O, ctive when IN0 on Control-RRC is ctive. (Control-RRC CW- Keyer function must be disbled). (defult) = Keyer, output to the rdio stright key input 2 = PTT, used s externl PTT 3 = Connect, ctive when the SIP-connection is ctive 4 = On/Off, controlled by the ON/OFF button on this side (*) 5 = Keyer PTT, ctive when CW is send vi the keyer (cn be used to key PA). If you set key dely in the Control-RRC this output will be ctivte key dely ms before the ctul CW-keying is strted. = Budot/45 used s output for RTTY bud. RTTY input vi USB virtul com port t Control-RRC. Connect PC softwre to the virtul com port nmed FSK COM. 7 = Budot/45 (inv) sme s bove but the RTTY key signl is inverted. OUT2 mode Select the function for output-2 (OUT2) signl the I/O connector (or ring in the PAD-jck). 0 = I/O, ctive when IN0 on Control-RRC is ctive. (Control-RRC CW- Keyer function must be disbled). = Keyer, output to the rdio stright key input. (defult) 2 = PTT, used s externl PTT 3 = Connect, ctive when the SIP-connection is ctive 4 = On/Off, controlled by the ON/OFF button on this side (*) 5 = Keyer PTT, ctive when CW is send vi the keyer (cn be used to key PA). If you set key dely in the Control-RRC this output will be ctivte key dely ms before the ctul CW-keying is strted. = Budot/45 used s output for RTTY bud. RTTY input vi USB virtul com port t Control-RRC. Connect PC softwre to the virtul com port nmed FSK COM. 7 = Budot/45 (inv) sme s bove but the RTTY key signl is inverted. (*) When the ON/OFF buttons re pushed the output chnge will be immedite, but will resume to lst sved position fter power on. To mke the chnges permnent use the "pply chnges" button. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 72 of 233

73 Ping settings (only Rdio-RRC) The Rdio-RRC hs Ping Wtchdog function which cn be used s n extr security. This function is quite common in network equipments. It cn be set to ping n IP ddress nd when it does not get ny nswer, it will mke hrd reboot of the RRC. The sttus of the ping wtchdog cn be checked t the sttus pge. This function is only vilble on the Rdio-RRC. Enble ping wtchdog IP ddress to ping Ping Intervl (seconds) Strtup dely (seconds) Filure count to reboot Enbles the function. No = Function is disbled Yes, test = Function enbled but it will not ctully reboot, cn be used for test Yes, reboot = Function is enbled. IP ddress to ping is entered here, In norml cses use the Gtewy IP. Intervl between the ping is sent. (-5535, defult 300 s) Dely before the first ping is sent. ( ), defult 300 s. If Test mode is ctivted it cn be set to Sets how mny times the ping is llowed to fil before reboot is done. (-255, defult 3 ) B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 73 of 233

74 Wi-Fi settings You cn enter SSID nd Pssword direct or check them on the WiFi pge. See more in the WiFi Chpter. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 74 of 233

75 Export settings (HTML) This function cretes text file with the ctul settings nd sttus of the unit. This file cn be sent vi emil for support purposes for exmple. Export settings (bin) This function is used to bckup your settings to file in your PC. When clicking on the link dilog box will show up where you cn decide where to store nd the nme of your bckup file. Note! The exported file will only include settings for the ctive profile. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 75 of 233

76 Import settings (bin) This function is used import your bckup file from your PC. Click on select file nd browse to your file nd then click import. Note tht the imported settings will be stored in the currently selected profile. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 7 of 233

77 Appliction firmwre upgrde The ppliction firmwre cn be updted over the Internet vi the web interfce when bugs re fixed nd/or new functionlity is implemented. You don't hve to be where the RRC- 25MkII is to do the updtes. Downlod the new firmwre from nd sve the file on your computer (it hs nme like RRC25-CRC_v.3_ bin). Connect to the RRC you wnt to updte nd select 'Appliction-upgrde'. Then click on the 'Browse' button nd select the file with the new firmwre. After tht you click on the 'Upgrde' button nd the new firmwre will be trnsferred nd sved into the RRC. When the firmwre is updted the RRC will restrt. Note -- Do not interrupt the upgrde process in ny wy. Wit minute or two then connect to the RRC gin nd select 'Info' nd verify tht the Softwre version is updted. If it looks like its not updted empty the web browser cche, to prevent it from showing n old cched pge. The updte NEVER fils but the browser is common problem. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 77 of 233

78 Bootloder firmwre upgrde This follows the sme steps s the ppliction firmwre upgrde procedure bove. Restrt device Restrt device cn be used if you wnt to reset nd restrt the RRC without sving ny chnges (before pply chnges) or just for ordinry reset. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 7 of 233

79 Configurtion with terminl-interfce All prmeters cn lso be progrmmed vi the seril interfce COM (RS-232) or Telnet port. COM hs the following settings: 3400 bud, bits, No prity, nd stop bit. Select the sys [s] nd setup-edit [] menus to configure the RRC. This method of configurtion is not user friendly nd should be voided. ========================= : udio c: codec d: debug e: extio f: flsh i: sip l: led q: udio qulity p: power r: rdio s: sys u: usb ========================= s sys ========================= : setup edit 2: setup view 3: setup cler 4: sntp 5: rtc : wdt reset 7: dns query : show network info 9: STUN test 0: memory : UDP send b: UDP receive c: Setup defult (Control) d: Setup defult 2(Rdio) r: COM-rts/cts on/off q: exit B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 79 of 233

80 WiFi Generl The RRC-25 cn be equipped with WiFi Interfce. A WiFi interfce is convenient when you wnt to connect the RRC:s to WiFi network. You do not need ny extr cbles or boxes. For the Control-RRC the min reson to use WiFi might be the portbility, nd for the Rdio-RRC to physiclly seprte the RRC from the telephone/dsl line which is the most common route for lightning storms to hit the RRC nd the Rdio. The WiFi Interfce is mounted on the pin heder P3 in the RRC-box. Units produced from the summer 202 hs P3 in plce from production. Units produced erlier do not hve P3 in plce you hve to solder to put it in plce, Instruction for how this is done cn be found on the Remoterig website under Support/Mods (hrdwre). B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 0 of 233

81 The 2.4 GHz Wifi Interfce is complint to 02.b/g nd single strem 02.n nd supports WPA2- (AES), WEP (4 nd 2 bit) modes of security in infrstructure mode nd lso TKIP in SPI mode. There is no limittions compred to Ethernet, ll settings tht re used when they re connected to Ethernet cn be used. The RRC utomticlly switch between WiFi or Ethernet. IF Ethernet is connected, Ethernet will be used. Connecting to Wifi network The esiest wy to setup the WiFi connection is to do it vi the Microbit Setup mnger. If you know the prmeters it cn be done from the web interfce lso, but you cnnot scn WiFi Networks tht wy so we focus on using the Setup mnger. Do not forget to connect 2V power to the RRC, the setup works when the unit is powered from USB but you cn not scn for WiFi networks until you connect 2V. The RRC cn store settings for up to different WiFi networks. The RRC will utomticlly connect to the strongest network from the list. You cn not force the RRC to connect to specific network, if you must do tht, you hve to remove the unwnted network from the list. - Disconnect the Ethernet cble if it s connected, Connect 2V to the RRC, nd connect the USB cble from your PC to the RRC. Strt the Microbit setup mnger - Select the WiFi tb B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

82 Click on the Get button. - You will get empty pge when the unit is not progrmmed, when you lter open this pge you will see the stored settings for your WiFi networks. Click Scn. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

83 - After second you will see the WiFi networks which re vilble t your current loction. The networks re sorted in order decided by Signl strength, the strongest on top. Up to 32 WiFi networks cn be shown. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 3 of 233

84 - Select the network you wnt to use by clicking on the button beside the SSID. - Click on the button on the row where you wnt to store the Network. - Click on the use button. - Enter the pssword (Privte shred key) if it s needed. - Click Sve nd close button. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 4 of 233

85 - Give The RRC few seconds to reboot nd connect to the WiFi Network. - Click on the Net info tb. - Click on the Get button. You will now see tht the Box hs got n IP-dress from the DHCP- server. If it still shows etc. wit moment nd click on the Get button gin B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 5 of 233

86 - Click on the Browse unit button. You will now see the RRC internl web pges(*). - Click on Info nd you will see the WiFi network sttus * - Your PC hs to be connected to the sme network s the RRC if it should be possible to connect to it. If the PC is connected to the sme WiFi Network, wireless isoltion must be switched off in the Router/ccess point. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

87 CW-Keyer Generl The RRC-25 hs CW-keyer function tht mkes CW opertion possible over Internet even if there re long ltencies nd lots of jitter. Note tht the CW-keyer is by defult disbled. The CW-keyer side-tone is generted loclly t the control RRC. When the dot or dsh is executed the udio from the rdio cn be muted t the Control-RRC to disble the rdio sidetone or nnoying clicks nd sounds. The time the mute function is ctive is defined by the lfdely setting. The vlue of lf-dely depends on the ltency of Internet. A good strt vlue is the sme vlue s the ping time between control nd rdio QTH. Another unique feture is kind of djustble jitter buffer t the rdio end. If the Internet connection hs vrying ltencies, you cn set key-dely before the keying of the rdio is executed. This dely mkes it possible to reconstruct the trnsmission on-the-fly nd the system will be much more tolernt ginst vrying ltencies (jitter). Longer key-delys give higher tolernce ginst jitter but lso dd dely until the keying is executed t the rdio. Even if you hve good connection you could try with low vlue. Remember tht when you increse this vlue you must lso increse the lf-dely vlue. Settings Keyer settings: Control Rdio Enble Yes Imbic Mode-A Pddle reverse No Weight [25-40] 30 Side tone hz [ ] 00 Side tone db [50-0] 20 Lf dely [0-500] 0 Key dely [0-250] 0 IO settings: Control Rdio IN0 mode USB DTR s CW OUT0 mode OUT mode OUT2 mode I/O No I/O I/O Keyer B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 7 of 233

88 Connections PAD Control-RRC: At the Control-RRC the PAD-jck is used to connect CW-pddle. The input is for stndrd 3.5 mm stereo plug. The left pddle is connected to the tip nd the right pddle to the ring. Common is connected to the inner ring nd house. Note - these signls re lso vilble in the I/O-connector. Signl PAD jck IO setting left-pddle tip - right-pddle ring - gnd inner ring - PAD Rdio-RRC: At the Rdio-RRC the PAD-jck is used to connect the output signl from the CW-keyer to the rdio stright-key input. The output is for stndrd 3.5 mm stereo plug. A stndrd cble with 3.5 mm connector in both ends cn often be used. Note - these signls re lso vilble in the I/O-connector. Signl PAD jck IO setting keyer-output tip OUT2 mode = Keyer keyer-output ring OUT mode = Keyer gnd inner ring - USB Control-RRC: A PC with stright-key functionlity cn be used to perform the keying, lone or in combintion with CW-pddle. To ctivte keying the PC could use the DTR signl in the virtul USB COM-port delivered by the RRC USB device. The PC control works in prllel with the CW-pddle so it is possible to shift between PC-keying nd the CW-pddle without chnging the configurtion. I/O-connector Control-RRC: A PC with stright-key functionlity or other externl keyer cn be used to perform keying, lone or in combintion with CW-pddle. To ctivte keying connect pin-4 (IN0) to GND. The externl keyer works in prllel with the CW-pddle so it is possible to shift between externl keying nd the CW-pddle without chnging the configurtion. Note - The stright-key input (IN0) is generic input nd cnnot be connected direct to PC, you need n interfce, see ppendix. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

89 Signl I/O connector IO setting right-pddle (IN) - left-pddle 2 (IN2) - stright-key/pc 4 (IN0) IN0 mode = Keyer gnd - I/O-connector Rdio-RRC: The output signl from the CW-keyer to the rdio stright-key input cn lso be found in the I/O connector. Signl I/O connector IO setting keyer-output 5 (OUT0) OUT0 mode = Keyer keyer-output (OUT) OUT mode = Keyer keyer-output 3 (OUT2) OUT2 mode = Keyer gnd - B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 9 of 233

90 RTTY Keying Generl Most HF-rdios hve specil FSK/RTTY keying input which is better to use thn AFSK (udio frequency shift keying) since you don t need to set mic gin nd other settings. The RRC-25 hs seprte seril chnnel for trnsfer of bud RTTY keying dt. The RTTY seril chnnel is only vilble vi the USB interfce. When instlling the Microbit Setup mnger USB-driver clled COMFSK is instlled In your RTTY PC-Softwre you should select the serilport number ssigned to the driver by Windows, in the exmple bove it s COM4. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 90 of 233

91 At the Rdio-RRC IO-settings pge you need to select which output you wnt to use for the RTTY keying signl. RTS from the RRC-25 COMFSK USB port is used to key PTT. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 9 of 233

92 RTTY with MMTTY The Remoterig specific settings to use MMTTY for RTTY is shown below. At the TX tb select the PTT & FSK comport to the sme comport s Device Mnger showed to be ssigned to RRC-25 COMFSK port, in this exmple it s COM4. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 92 of 233

93 At the Misc tb e select COM-TxD(FSK) nd click on the USB Port button. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 93 of 233

94 In the USB port option dilog select C-limiting speed. If not limiting speed is selected the PTT will be relesed before the whole RTTY string is sent, becuse the USB communiction is so much fster thn ordinry RS-232 seril port. Settings IO settings: Control Rdio OUT0 mode - OUT mode Budot/45 OUT2 mode Keyer B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 94 of 233

95 Connections PAD Control-RRC: Only the USB interfce cn be used for RTTY s described bove. PAD Rdio-RRC: At the Rdio-RRC the PAD-jck cn be used to connect the RTTY signl from the FSK seril port. The PAD will then be shred with CW key output. The pd jck is for stndrd 3.5 mm stereo plug. Note - these signls re lso vilble in the I/O-connector. Signl PAD jck IO setting keyer-output tip - keyer-output ring OUT mode = Budot/45 gnd inner ring - USB Control-RRC: A PC with suitble softwre like MMTTY cn be used to perform the RTTY keying. Together with the RTTY keying signl PTT need to be ctivted this is done by ctivting the RTS signl in the virtul comport (COMFSK). MMTTY does this by defult other softwre my need mnul configurtion. I/O-connector Rdio-RRC: The output signl for the RTTY keying cn lso be found in the I/O connector. Signl I/O connector IO setting RTTY- output 5 (OUT0) OUT0 mode = Budot /45 RTTY -output (OUT) - RTTY -output 3 (OUT2) - gnd - The I/O connector cn lso be used for the PTT signl if the Mic PTT is not used. If you wnt this function chnge one of the free outputs to PTT. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 95 of 233

96 ICOM CI-V Generl RRC-25MkII supports the CI-V protocol used by lmost every ICOM rdio. Then you hve to use PC-softwre e.g. HmRdioDeLuxe or similr rig control softwre t the control site. All udio nd dt communiction goes true the RRC:s nd you don't need PC t the remote site. The Connect/Disconnect button on the web sttus pge is used to connect/disconnect to/from the remote site. It cn lso be done by the UP-button on the microphone or be set to lwys be connected. Hrdwre configurtion Norml: B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 9 of 233

97 SIP-Connect/disconnect vi MIC UP button: Rdio settings (exmple) Prmeter Control Rdio Progrm mode ICOM CI-V ICOM CI-V SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-25MkIIs, remember tht the bndwidth demnd is doubled. Connections Drwings of the connection cbles cn be found under ppendix B. Control-RRC: Connect Remoterig-I0c cble or stndrd RS-232 cble between the PC nd the RRC COM2. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 97 of 233

98 The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector, like the HM-03. If you hve microphone with circulr connector like HM-3 you hve to use the Remoterig I0 cble, the OPC-59, from ICOM or mke one by yourself (drwing for I0 is provided). The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: From the RRC TTL connector to the rdios CI-V jck you cn use the Remoterig Ic cble or mke it by your self. The cble should hve 4/ modulr connector in one end nd 3.5 mm stereo plug in the other end. The 3.5 mm plug is connected to the rdio CI-V jck. Between the RRC AUX/MIC connector nd the rdios microphone jck you cn connect stndrd ptch cble if the rdio hve RJ-45 jck. If the rdio hve circulr microphone jck you cn use the Remoterig I or mke the cble by yourself. (drwings for I is provided). Mke the cble s short s possible to prevent it from picking up HF. The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd "off- the-shelf cble with 3.5 mm stereo plugs in both ends. I,I0 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 9 of 233

99 Mic Inp -pol Circulr mle I0 screened 20 cm :2 Generic ICOM cbles RRC-25MkII -pol RJ 45 Con 25 Cble I0 () USER MANUAL UP AF V UP 2 2 PC COM2 Front pnel view GND MIC MICE PTT DSUB- 9pol Femle RRC-25MkII GND MIC MICE PTT I0c DSUB- 9pol Mle V SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 99 of 233

100 SPEAKER 3.5 mm stereo plug TTL 4/ modulr RRC-25MkII GND RDO TDO Ib Ic :2 Generic ICOM cbles RRC-25MkII Cble I () Front pnel view SPEAKER 3.5 mm stereo plug CI-V 3.5 mm stereo plug USER MANUAL PTT PTT MIC MIC AUX/MIC -pol RJ 45 Con V AF MICE GND PWR ON indiction I screened m V -pol Circulr femle AF MICE GND B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 00 of 233

101 ICOM IC-700 Generl The ltest HF/VHF/UHF rig from ICOM re supported by Remoterig. You get full remote functionlity from the control pnel nd the feeling is exctly s if you use them loclly. It s one of the simplest rig to setup nd come on the ir with. No specil cbles needed, just connect the RJ45:s nd setup the prmeters in the boxes. When you press the power button on the pnel the rdio comes to life t the remote side nd sound nd pnel info flows cross the Internet between the pir of RRC-25MkII:s. Hrdwre configurtion B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 0 of 233

102 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 2 IC-700/IC-70/IC IC-700/IC-70/IC-703 SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-25MkIIs. Connections All necessry signls between the pnel nd the rdio re connected vi the wires in the cble between the control pnel nd the rdio body. The cble is stndrd CAT- shielded ptch cble. We just need to dd one cble nd connect RRC-25MkII in ech end. The following signls re represented in the cble. V power to control pnel (only when rdio is ON) 2 PWR SW - power switch, grounding it switch on the rdio 3 AF - udio to speker. 4 TXD - seril dt 3400 bps from rdio to pnel 5 MICE - mic ground MIC- mic Signl 7 GND RXD - seril dt 3400 bps from pnel to rdio B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 02 of 233

103 Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS output. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 03 of 233

104 ICOM IC-703, IC-70 Generl The ide of remote controlling IC-703/70 is simple; it's just to extend the cord between the rdio nd the control pnel using Internet. When you press the power button on the pnel the rdio comes to life t the remote side nd sound nd pnel info flows cross the Internet between the pir of RRC-25MkII:s. The look nd feel of the pnel is the sme s if the pnel ws directly connected to the rdio. Hrdwre configurtion B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 04 of 233

105 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 2 IC70 2 IC70 SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-25MkIIs. Connections All necessry signls between the pnel nd the rdio re connected with the wires in the cble OPC-5 or OPC-57 from ICOM. We just need to cut it prt nd connect RRC- 25MkII in ech end. The following signls re represented in the cble, (the numbering is for the RJ45 connector to the RRC fter converting the cble, not for the ICOM connector): V power to control pnel (only when rdio is ON) 2 LRXD - seril dt 9200 bps from pnel to rdio 3 AF - udio to speker. 4 PWK - power control, grounding it switch on the rdio 5 MICE - mic ground MIC- mic Signl 7 GND LTXD - seril dt 9200 bps from rdio to pnel Cut the ICOM cble (OPC-5 or OPC-57) nd connect both ends to stndrd CAT-5 ptch cble for computer networks, use shrinking tubes to protect the soldering. One problem is tht the ICOM cble is very soft nd there is more sewing tred thn copper wire. The copper wire is lso vrnished to mke it even more difficult. Before you connect the cbles to the RRC:s, plese check the cbles by connecting them together with 2xRJ45 connector. Also py ttention to tht speker or hedset must be connected to the speker jck on the IC- 70 front-pnel otherwise the no udio will be sent from the microphone to the rdio. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 05 of 233

106 Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 0 of 233

107 :2 Splitted Cble for IC70 RRC 25 / RRC-25MkII (CAT-5) 25 Cble () USER MANUAL Pnel Rdio -pol ICOM-con -pol RJ 45 Con -pol RJ 45 Con -pol ICOM-con 3 Blue V Ornge/White Ornge/White V Blue 3 Yellow LRXD Ornge 2 2 Ornge LRXD Yellow 4 Red AF Green/White 3 3 Green/White AF Red 4 White PWK Blue 4 4 Blue PWK White 5 MICE Blue/White 5 5 Blue/White MICE 5 White MIC MIC White 7 GND 7 7 GND 7 2 Blck LTXD LTXD Blck 2 Screen to White Screen to White Green Green Screen to Red Brown/White Brown/White Screen to Red Convert from ICOM-cble to -pol CAT-5 cble Brown Brown Convert from ICOM-cble to -pol CAT-5 cble B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 07 of 233

108 Prepre the seprtion cble to IC-703 nd IC-70 The cble between front nd rdio before it is cut prt. You hve to buy this cble from your locl ICOM-deler (rt no OPC-5 or OPC-57). Connector t rdio end. Connector t control pnel end. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 0 of 233

109 - Identify the end with the connector to the rdio, se bove. - Cut the cble prt, don't mke it longer then needed t rdio end. The mic signl is sensitive of HF from ntenns etc. s usully. - Tke wy bout 40 mm of the outer covering. - Seprte the shields from the inner wire, the red wire hs copper coloured shield nd the white hs green shield. The shielded white wire is thinner thn the white one without shielding. Tht wy you cn identify them from ech other. The outer shielding is not connected to the RRC. - Cut ll wire to bout 20 mm. Tke wy bout 3 mm of the cover from ech wire nd tin-plte them. It's not esy but it's possible. - Also tin-plte the copper nd green shielding. - Use the supplied CAT-5 cble cut of 0-5 cm from ech connector nd tke wy 40 mm of the outer cover. - Seprte the pirs. - Tke wy 3 mm of the cover from ech wire nd tin-plte them. - Identify the following colours:. Ornge/White 2. Ornge 3. Green/White 4. Blue 5. Blue/White. Green 7. Brown/White. Brown B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 09 of 233

110 - Cut piece of shrinking tube to ech wire. Cut them short enough so they don't shrink from the het of the solder iron. - First tred 00 mm long,4 mm shrinking tube on the seprtion cble. - Then tred 0 mm long,4 mm shrinking tube on the seprtion cble. - Solder them together, follow the drwing bove. - Tred the shrinking tubes over the soldered joints nd shrink them with hot ir. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 0 of 233

111 - Tred the.4 mm shrinking tube over the joint nd shrink it with hot ir. - Tred the second shrinking tube over the first nd shrink them with hot ir - The first cble is now finished, Do the sme with the other prt. The one with the connector to the control pnel. When you hve finished both cbles, connect them together with the supplied RJ45 extender. - Check the cble with n ohm-meter. You should hve connection from pin t rdio end to pin t rdio end etc. Also check for short circuits between the pins. - Connect the cble between pnel nd rdio nd check the functionlity. Don't forget the microphone. ( this should be done without involving the RRC.s t this moment. When everything is OK you cn connect the cbles to the RRC:s B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

112 ICOM IC-R2500 Generl The technicl solution is the sme s for IC-70 nd TS-40; you cn remote control the receiver over Internet from the control pnel without ny PC. We simply replce the cble between the control pnel nd the receiver with two RRC-25 units, one t the control pnel nd one t the receiver. When you push the PWR-ON button n udio nd dt connection is estblished between the units nd you control the receiver s you do normlly with the control pnel ttched directly to the receiver. Hrdwre configurtion Rdio settings (exmple) Prmeter Control Rdio Progrm mode 7 ICR ICR2500 SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No/Yes Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-25MkIIs, remember tht the bndwidth demnd is doubled. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

113 Connections The cbling is quite simple nd cn be done with simple RJ connectors. Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 3 of 233

114 :2 ICOM cble RRC-25MkII to IC-R2500 Pnel end 25 Cble I4 () USER MANUAL HV HV TDO TDO GND GND RDO RDO PWR SW PWR SW Control Pnel IC-R2500 -pol Modulr RRC-25MkII MIC/AUX pol Modulr Con SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 4 of 233

115 SPEAKER 3.5 mm stereo plug RRC-25MkII MIC/AUX pol Modulr Con Control Inp IC-R2500 pol Modulr Con :2 ICOM cble RRC-25MkII to IC-R2500 Rdio end 25 Cble I5 () SPEAKER 3.5 mm stereo plug USER MANUAL PWR SW PWR SW GND GND RDO RDO TDO TDO HV HV B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 5 of 233

116 ICOM IC-E220 Generl It's not only shortwve trnsceivers which could be remote controlled, the remoterig system lso support ICOM:s D-str rdio IC-E220. The technicl solution is the sme s for IC-70 nd TS-40; you cn remote control the rdio over Internet from the control pnel without ny PC. We simply replce the cble between the control pnel nd the rdio with two RRC- 25 units, one t the control pnel nd one t the rdio. When you push the PWR-ON button n udio nd dt connection is estblished between the units nd you control the rdio s you do normlly with the control pnel directly ttched to the rdio. Hrdwre configurtion Rdio settings (exmple) Prmeter Control Rdio Progrm mode 9 IC-E220 9 IC-E220 SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

117 COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-25MkIIs Connections The cbling is quite simple nd cn be done with simple RJ connectors. Be wre of tht the originl microphone cn not be used without the HM-33 dpter bords. If you do not hve them use simple ICOM microphone like HM-03 or HM-95. Microphones with circulr connectors cn lso be used with dpter cble OPC-59. Control-RRC: You hve to mke the control cble I3 to connect between the Control pnel nd the RRC TTL connector. Mrk up the cble so you connect the connectors to the right unit, it will not work if you try to use it connected bckwrds. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: You hve to mke the control cble I2b to connect between the Rdio-RRC nd the Rdio. Mrk up the cble so you connect the connectors to the right unit, it will not work if you try to use it connected bckwrds. Between the RRC AUX/MIC connector nd the rdios microphone jck you cn connect stndrd ptch cble (CAT5 or CAT) I2. The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd "off- the-shelf cble with 3.5 mm stereo plugs in both ends. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 7 of 233

118 Using HM-33 Microphone If you hve RRC-25MkIIs you cn buy the HM-33 dpter pcbs which let you use the HM-33 microphone with ll it s buttons. The smll pcbs re mounted in the strpping sockets which mens tht no red strps re needed. The pcb with the yellow cble re mounted in the Control-RRC nd the pcb with the blue cble re mounted in the Rdio-RRC. The yellow nd blue cbles need to be solder to one point on the RRC pcb. See pictures below. Be sure to remove power when solder. There No settings need to be chnged fter mounting the pcbs. There is one solder pd which is significntly bigger thn the other vi holes to the right of the CPU over the Crystl. Tht s the one which the cbles should be soldered to. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

119 Control-RRC Rdio-RRC B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 9 of 233

120 Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 20 of 233

121 4 Control Pnel IC-E220 4-pol Modulr V GND TDO RDO I3 RRC-25MkII TTL 4/ pol Modulr Con V GND RDO TDO :2 ICOM cble RRC-25MkII to IC-220 Pnel end SPEAKER 3.5 mm stereo plug 25 Cble I3 () USER MANUAL B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

122 SPEAKER 3.5 mm stereo plug RRC-25MkII -pol RJ 45 Con RRC-25MkII 4/ pol Modulr Con Mic Inp IC-E220 -pol RJ 45 Con Control Inp IC-E220 4/ pol Modulr Con 2 V V 2 3 GND GND RDO TDO TDO RDO 4 5 I2b :2 ICOM cble RRC-25 to ICOM IC-E220 Rdio end SPEAKER 3.5 mm stereo plug 25 Cble I2 () USER MANUAL MIC MIC 7 7 Try Stndrd shielded CAT 5 PTT PTT MICE MICE GND GND I2 I2c B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 22 of 233

123 ICOM ID-E0 Generl The Remoterig system lso support ICOM:s D-str rdio ID-E0. The technicl solution is the sme s for IC-70 nd TS-40 etc. You cn remote control the rdio over Internet from the control pnel without ny PC. We simply replce the cble between the control pnel nd the rdio with two RRC-25 units, one t the control pnel nd one t the rdio. When you push the PWR-ON button n udio nd dt connection is estblished between the units nd you control the rdio s you do normlly with the control pnel directly ttched to the rdio. Hrdwre configurtion The hrdwre preprrions is little bit more complicted for the IC-E0 s some modifictions must be done t the Remoterig circuit bords. The HM-33 dpters must be mounted nd wire must be connected, more info below. Rdio settings (exmple) Prmeter Control Rdio Progrm mode 3 IC-E0 3 IC-E0 SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-25MkIIs Connections The cbling is quite simple nd cn be done with simple RJ connectors. Be wre of tht the HM-33/0 dpter bords must be used Drwings of the connection cbles cn be found below. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 23 of 233

124 Control-RRC: You hve to mke the control cble I20 to connect between the Control pnel nd the RRC TTL connector. Mrk up the cble so you connect the connectors to the right unit, it will not work if you try to use it connected bckwrds. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: You hve to mke the control cble I9 to connect between the Rdio-RRC nd the Rdio. Mrk up the cble so you connect the connectors to the right unit, it will not work if you try to use it connected bckwrds. Between the RRC AUX/MIC connector nd the rdios microphone jck you cn connect stndrd ptch cble (CAT5 or CAT). The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd "off- the-shelf cble with 3.5 mm stereo plugs in both ends. HM-33/0 Microphone dpter bords If you hve RRC-25MkIIs you cn buy the HM-33/0 dpter pcbs which re needed for the function together with the IC-E0. The smll pcbs re mounted in the strpping sockets which mens tht no red strps re needed. The pcb with the yellow cble re mounted in the Control-RRC nd the pcb with the blue cble re mounted in the Rdio-RRC. The yellow nd blue cbles need to be solder to one point on the RRC pcb. See pictures below. Be sure to remove power when solder. There is no settings tht need to be chnged fter mounting the pcbs. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 24 of 233

125 There is one solder pd which is significntly bigger thn the other vi holes to the right of the CPU over the Crystl. Tht s the one which the cbles should be soldered to. Control-RRC B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 25 of 233

126 Rdio-RRC Modifictions of the Control-RRC circuit bord One resistor must be removed nd wire must be solder between two pds. You need fine solder iron nd short piece of insulted thin wire nd mybe little piece of tin. Don t use ny soldering brid or pumps they my dmge the pcb. - Remove the resistor by heting the ends of the resistor, lternte from left to right end stying few seconds t ech end until the component come loose. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

127 - Solder the thin insulted wire between the solder pds s shown on the picture below. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 27 of 233

128 Modifictions of the Rdio-RRC circuit bord One resistor must be removed nd wire must be solder between two pds. You need fine solder iron nd short piece of insulted thin wire nd mybe little piece of tin. Don t use ny soldering brid or pumps they my dmge the pcb. - Remove the two 0 ohms resistors by heting the ends of the resistor, lternte from left to right end stying few seconds t ech end until the component come loose. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

129 - Solder the thin insulted wire between the solder pds s shown on the picture below. Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 29 of 233

130 PWR ON GND GND RD TD V Control Pnel IC-E0 -pol Modulr RRC-25MkII TTL pol Modulr Con White Blck 2 3 Blck Blue Green Yellow 4 5 Yellow Green 5 Blue White I20b :2 ICOM cble RRC-25MkII to ID-E0 Pnel end SPEAKER 3.5 mm stereo plug 25 Cble I20 () USER MANUAL Red Red B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 30 of 233

131 SPEAKER 3.5 mm stereo plug RRC-25MkII / pol Modulr Con Blck Control Inp ID-E0 / pol Modulr Con White Blck 2 Red 3 Green White Blue I9b I9c :2 ICOM cble RRC-25 to ICOM ID-E0 Rdio end PWR ON GND GND RD TD V 25 Cble I9 () SPEAKER 3.5 mm stereo plug USER MANUAL MIC MIC 7 7 Green Yellow RRC-25MkII -pol RJ 45 Con Blue Red Yellow Try Stndrd shielded CAT 5 PTT PTT I9 Mic Inp ID-E0 MICE MICE GND GND -pol RJ 45 Con B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 3 of 233

132 SPEAKER 3.5 mm stereo plug RRC-25MkII -pol RJ 45 Con RRC-25MkII Control Inp ID-E0 / pol Modulr Con / pol Modulr Con White White 2 3 Blue Red Blck Red Yellow Green 4 5 Green Yellow 5 Blck Blue I2b I2c Mic Inp ID-E0 :2 ICOM cble RRC-25 to ICOM ID-E0 Rdio end, RRC v7 -pol RJ 45 Con PWR ON GND GND RD TD V 25 Cble I2 () SPEAKER 3.5 mm stereo plug USER MANUAL MIC MIC 7 7 Try Stndrd shielded CAT 5 PTT PTT MICE MICE GND GND I2 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 32 of 233

133 PWR ON GND GND RD TD V Control Pnel IC-E0 -pol Modulr 2 RRC-25MkII TTL pol Modulr Con 3 4 Green Yellow 4 5 Yellow Blue Green Blck 5 I22b I22c :2 ICOM cble RRC-25MkII to ID-E0 Pnel end, RRC v7 2 3 SPEAKER 3.5 mm stereo plug 25 Cble I22 () USER MANUAL White White Red Red Blck Blue B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 33 of 233

134 ICOM IC-2725 Generl It's not only shortwve trnsceivers which could be remote controlled, the remoterig system lso support ICOM:s IC The technicl solution is the sme s for IC-70 nd TS-40; you cn remote control the rdio over Internet from the control pnel without ny PC. We simply replce the cble between the control pnel nd the rdio with two RRC-25 units, one t the control pnel nd one t the rdio. When you push the PWR-ON button n udio nd dt connection is estblished between the units nd you control the rdio s you do normlly with the control pnel directly ttched to the rdio. There re no limittions in functionlity, everything works nd you cn use the originl microphone. Hrdwre configurtion Unfortuntely ICOM hve inverted the seril bus in the IC-2725 so there need hrdwre dption to mke it work. This is quite simple so it cn be done by yourself. The dpters cn lso be bought from Remoterig webshop. The dpters re connected to the strpping socket where the red jumpers re normlly connected. The trnsistors used on the PCB hve built in resistors, so if you use stndrd trnsistor like BC-547 nd BC-557 you hve to put the resistors outside. Check the dt sheets for PDTC-43ET nd PDTA-44ET. Control side B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 34 of 233

135 Rdio side Microbit Adpters 25L When ssembling the dpter pcb:s tke notice tht they re not the sme in the different units, one is mrked Control nd the other Rdio. Be sure to put them in the right RRC nd tht they re turned ccording to the picture below. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 35 of 233

136 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 7 ICR2500/IC ICR2500/IC-2725 SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No/Yes Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-25MkIIs, remember tht the bndwidth demnd is doubled. Connections The cbling is quite simple nd cn be done with simple RJ connectors. Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 3 of 233

137 Control Pnel IC pol Modulr :2 ICOM cble RRC-25MkII to IC-2725 Pnel end RRC-25MkII MIC/AUX pol Modulr Con HV DATA DATA MICE MIC GND SPEAKER 3.5 mm stereo plug 25 Cble I () USER MANUAL B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 37 of 233

138 4 SPEAKER 3.5 mm stereo plug RRC-25MkII MIC/AUX pol Modulr Con HV DATA DATA MICE MIC GND Control Inp IC-2725 pol Modulr Con :2 ICOM cble RRC-25MkII to IC-2725 Rdio end Cble I7 () SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 3 of 233

139 YAESU TWIN Generl RRC-25MkIIs Yesu Twin supports the specil high end concept where one Yesu rdio cn be used to control nother Yesu rdio. No PC:s needed t either end. The RRC-25MkIIs Yesu Twin pckge includes power supplys nd ll necessry cbles. The boxes do not need to be opened ll strppings re done in production. All you need to do is to put the system together nd do the IP-settings. The twin concept is minly developed for using with two rdios of the sme model for exmple two FT-5000, but two different models cn lso be used. The following combintions of re tested: Control FT-450 FT-950 FT-950 FT-2000 FT-2000 FT-5000 FT-5000 FT-9000 FT-9000 Rdio FT-450 FT-950 FT-5000 FT-2000 FT-5000 FT-5000 FT-9000 FT-5000 FT-9000 In the combintions tested bove ll functions works nd re tested by severl test pilots, nywy we cnnot give ny gurnties tht we hve not missed some minor function. The meter functions in the FT-950 hve some limittions, the PWR, SWR nd ALC re replicted to B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 39 of 233

140 the controlling rdio but there is no scle mrks on the meters so you hve to lern how the different vlues re represented. For the FT-9000 FT-9000 the sub RX must be ctive for the ALC meter to work, nd of course the spectrum scope does not work remotely. Attention! If you wnt to use the Auto tuner on the Remote rdio, it s very importnt tht you connect dummy lods to the corresponding ntenn ports on the control rdio. As the rdio do not use full power when tuning nd it s done reltively fst, smll nd chep 0-20W dummy lods cn be used (not included). Hrdwre configurtion In the stndrd RRC:s the strppings re done mnully by the customer, but In the RRC- 25MkIIs Yesu Twin pckge the strppings re done by smll pcb mrked 25Y which is ssembled t the strpping re. The smll pcb is removble if you lter wnt to use the RRC:s for some other configurtion. When you replce it is importnt tht the notch which mrks pin one is plced ccording to the picture below. For your reference the picture below shows how the strppings re done on the smll pcb. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 40 of 233

141 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 0 Yesu FT- 450/950/2K/5K/9K twin 0 Yesu FT- 450/950/2K/5K/9K twin SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio Dul-RX - Yes (*) Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte 3400(*2) 3400(*2) COM0 dt bits COM0 stop bits COM0 prity 0 Off 0 Off (*) Remember tht the bndwidth demnd is doubled if Dul-RX is ctivted. (*2) Set the CAT speed in both Rdios to 3400 bud, nd set RTS to No B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 4 of 233

142 Connections Drwings of the connection cbles cn be found below. All necessry cbles re included in the pckge. Control site Connect 2V power supply to the PWR jck 2 Connecter Ethernet to the Ethernet jck ( 2m CAT 5 cble included) 3 Connect the CAT cble Y5d from the COM2 connector to the rdio CAT connector 4 Connect the microphone vi the Microphone dpter cble Y5 5 Connect speker to the speker jck (spekers nd cble re not included) Connect pddle to the PAD jck ( dpter from ¼ connector to 3.55 mm included) 7 Connect dummy to the hedset jck on the trnsceiver to quiet the Internl speker. Connect Dummy lods to the Antenn jcks (not included) B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 42 of 233

143 Rdio site Connect 2V power supply to the PWR jck 2 Connecter Ethernet to the Ethernet jck ( 2m CAT 5 cble included) 3 Connect the CAT cble Yd from the COM2 connector to the rdio CAT connector 4 Connect the mic cble Y from the AUX/MIC jck to the rdio mic connector. 5 Connect the udio cble from to the SP jck to the rdio hedphone output. (Adpter from ¼ connector to 3.5 mm included) Connect the keying cble from the PAD jck to the rdio key input (Adpter from ¼ connector to 3.55 mm included) B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 43 of 233

144 Logging or computer control, RTTY etc. Even if the CAT connector t the Remote Rdio is occupied with the communiction between the two Rdios it is possible to connect other equipment to the system due to n intelligent CAT server functionlity in the RRC.s. If you need to connect ntenn switch for exmple which need to tlk to the remote Rdio you cn connect it to the Rdio-RRC COM nd configure COM to Mode, CAT to COM2 (locl). If you wnt to connect logging or PC-control softwre to the system you cn connect it to the Control-RRC COM vi RS-232 or USB nd configure both RRC:s COM to Mode-, CAT to COM2 (locl). You cn still use the remote ntenn switch s described bove. Independent of the connections bove you cn use the Remote Rdios FSK trnsmission. Configure Rdio-RRC OUT mode = Budot/45 nd use the Virtul USB port COMFSK for the RTTY softwre. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 44 of 233

145 Cble Y5d Control Rdio to Control-RRC COM2 Cble Yd Rdio-RRC to Remote Rdio COM2 Cble Y5 Mic to Control-RRC Mic jck Cble Y Rdio-RRC Mic jck to Rdio Mic input Cble 3.5 mm 3.5 mm Audio Output from Remote rdio to Rdio-RRC SP input jck Cble 3.5 mm ¼ Keyer from Rdio-RRC PAD jck to Remote rdio stright key input jck B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 45 of 233

146 Adpter ¼ to 3.5 mm Hedset dpter Adpter ¼ to 3.5 mm Pddle dpter Adpter 3.5 mm to ¼ Hedset output dpter from remote remote rdio Control-RRC: Connect the RS-232 cble Y5d between the Control-RRC COM2 nd the CAT connector on the Rdio. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. If you hve microphone with circulr connector use the dpter cble Y5. The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Pddles re connected to the PAD jck. If you the pddles hve ¼ plug on your pddle use the supplied ¼ to 3.5 mm dpter cble. Connect the CAT 5 cble from the Ethernet jck to your switch or router Connect the 2V power supply to the DC jck Rdio-RRC: Connect the RS-232 cble Yd from the Rdio-RRC COM2 connector to the rdios CAT connector. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 4 of 233

147 Connect the mic cble Y from the Rdio-RRC AUX/MIC connector to the rdios microphone jck. Connect the speker signl from the rdios hedset output jck or similr to the Rdio- RRC SP jck with the stndrd 3.5 mm 3.5 mm cble with stereo plugs in both ends. If the rdio hve ¼ jck use the supplied dpter ¼ to 3.5mm. Connect keyer cble (stndrd 3.5 mm 3.5 mm cble with stereo plugs in both ends) from the Rdio-RRC PAD jck to the stright key input jck on the Rdio. If the rdio hve ¼ jck, use the supplied 3.5 mm to ¼ dpter. Connect the CAT 5 cble from the Ethernet jck to your switch or router Connect the 2V power supply to the DC jck B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 47 of 233

148 FT-950/2000/5000/9000 CAT port :2 YAESU TWIN Cbles RRC-25MkII to Rdio (twin Control side) RRC-25MkII 25 Cble Y5 () USER MANUAL Front pnel view Mic Inp -pol Circulr GND PTT MIC MICE Y5d DSUB- 9pol Femle Sme s Yesu ADMY-7 Y5 RRC-25MkII -pol RJ 45 Con GND PTT MIC MICE DSUB- 9pol Mle COM2 5 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 4 of 233

149 7 Rdio CAT port DSUB- 9pol Femle 7 :2 YAESU TWIN cbles RRC-25MkII -> Rdio (twin rdio side) GND 25 Cble Y () USER MANUAL PTT PTT SPEAKER 3.5 mm stereo plug RRC-25MkII pol RJ 45 Con MICE DSUB- 9pol Femle MIC MIC GND GND RRC-25MkII COM2 Y Yb Mic Inp -pol Circulr MICE 7 5 Front pnel view SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 49 of 233

150 YAESU FT-57 Generl The Remoterig system supports the populr Yesu FT-57. The technicl solution is the sme s for ll the other rigs like IC-70 nd TS-40 etc with detchble control pnel. You cn remote control the rdio over Internet from the control pnel without ny PC. We simply replce the cble between the control pnel nd the rdio with two RRC-25 units, one t the control pnel nd one t the rdio. When you push the PWR-ON button n udio nd dt connection is estblished between the units nd you control the rdio s you do normlly with the control pnel directly ttched to the rdio. Hrdwre configurtion The FT-57 is fully supported by the Remoterig RRC-25MkIIs from hrdwre version 7. Erlier version of the RRC:s cn lso be used but then some hrdwre chnges or specil cbling re needed, See t the website under Support nd Mods. If you hve set of RRC:s hrdwre 7 or lter you only need to mke cbles. The cbles re lso vilble from the web shop. Attention! The FT-57 cn enter stte where it s bsolutely unrechble until you remove the 3.V Power source. Reset of the RRC doesn t help, even fysicl disconnect of the RRC doesn t help. This hppens rrely but if you hve the rdio on QTH where you hve no one who cn switch off the power supply you must instll remote controlled switched so you cn switch off the 3,V power to the rdio. For exmple Webswitch 2H, or GSM Switch, If you do no use ll outputs on the RRC-25 you cn use one of the outputs to control rely which cn switch off the 3.V power to the Rdio. Also be wre of tht the FT-57 lmost mkes short circuit to the 3.V power for short moment when it s powered ON. If you hve the Rdio-RRC connected to the sme Power Supply it cn cuse the RRC do reset. If it s the cse power the RRC-from seprte PS. This B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 50 of 233

151 cn hppen even with some 25A power supplies. You will see if the RRC reset by wtching the PWR LED, or checking the Uptime in the web interfce. Note! The strpping instructions bove re only vlid for RRC:s from hrdwre version 7. Also remember to remove JMP-5 in both the control nd rdio RRC. Rdio settings (exmple) Prmeter Control Rdio Progrm mode 5 FT-57 5 FT-57 SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-25MkIIs B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 5 of 233

152 Connections The cbling is quite simple nd cn be done with simple RJ nd modulr connectors. The 5 wire control cbles re the sme on control nd rdio end, but be wre of tht the cbles must be connected s shown in the schemtics. Drwings of the connection cbles cn be found below. Control-RRC: The control cble Y9 should be connected between the Control pnel nd the RRC TTL connector. The Y9 cble is included in the FT-57 pckge. The cble hs yellow mrk in the RRC end, it will not work if you try to use it connected bckwrds. The originl microphone cn be connected direct to the RRC AUX/MIC connector. The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug or to the FT-57 front pnel speker jck. Rdio-RRC: The control cble Y9 should be connected between the Rdio-RRC nd the Rdio. The Y9 cble is included in the FT-57 pckge. The cble hs yellow mrk in the RRC end, it will not work if you try to use it connected bckwrds. Between the RRC AUX/MIC connector nd the rdios microphone jck you cn connect the stndrd screened ptch cble (CAT5 or CAT) included in the FT-57 pckge. Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 52 of 233

153 DET NR. CNT NAME DIMENSION NOTE CONSTR. DRAWN COPIED CHECKED STAND. OK SCALE REPLACE REPLACED BY MS :2 YAESU FT-57 Cble Contr. pnel -> RRC-25MkII DRAWING NR DATE Cble Y9 () USER MANUAL Ctrl Pnel FT-57 -pol modulr Y9 RRC-25MkII TTL PWR SW V GND RXD TXD SP -pol modulr SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 53 of 233

154 RRC-25MkII AUX/MIC DET NR. CNT NAME DIMENSION NOTE CONSTR. DRAWN COPIED CHECKED STAND. OK SCALE REPLACE REPLACED BY MS MIC :2 YAESU FT-57 cble RRC-25MkII -> Rdio FT-57 DRAWING NR DATE Cble Y9 () USER MANUAL MICE MICE pol RJ 45 Con RRC-25MkII TTL Try Stndrd shielded CAT 5 MIC MIC PTT PTT GND GND -pol modulr PWR SW V GND RXD TXD SP Y9b Y9 -pol RJ 45 Con CTRL FT-57 -pol modulr B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 54 of 233

155 YAESU FTM-350 Generl Speker AF CON RRC-25MkIIs The Remoterig system supports the Yesu FTM-350. The technicl solution is the sme s for ll the other rigs with detchble control pnel. You cn remote control the rdio over Internet from the control pnel without ny PC. We simply replce the cble between the control pnel nd the rdio with two RRC-25 units, one t the control pnel nd one t the rdio. When you push the PWR-ON button n udio nd dt connection is estblished between the units nd you control the rdio s you do normlly with the control pnel directly ttched to the rdio. Hrdwre configurtion The FTM-350 is supported by the Remoterig RRC-25MkIIs from version 5 s it needs dul udio support. The smll built in spekers in the control pnle cn not be used, seprt spekers hs to be connected direct to the Control-RRC speker jck. As the mic levels between the control pnel nd the rdio is very different compred to other (much higher) smll mod must be donet to the Rdio-RRC pcb. A 0K resistor hs to be mounted in prllell with R7. This is done quite esy, see picture below. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 55 of 233

156 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 7 FTM FTM-350 SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx Yes Codec out gin Codec inp gin 20 0 Codec inp premp No Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 5 of 233

157 Connections The cbling is quite simple nd cn be done with stndrd ptch cbles. Drwings of the connection cbles cn be found below. Control-RRC: The control cble Y3 stndrd RJ-45 ptch cble should be connected between the Control pnel nd the AUX/MIC connector. The originl microphone should be connected direct to the rdio front pnel s usul. A pir of spekers re connected direct to the RRC SP-jck with 3.5 mm stereo plug. A set of mplified PC spekers will work very well lso. Rdio-RRC: The control cble Y4 stndrd RJ-45 ptch cble should be connected between the Rdio-RRC AUX/MIC jck nd the Rdio. The speker cble (Y4bc) eg. stndrd cble with 3.5 mm mono connectors in both ends should be connected between the rdio nd the Rdio-RRC speker jck. Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 57 of 233

158 RRC-25MkII AUX/MIC Y3b :2 YAESU FTM-350 Cbles Front -> RRC-25MkII MIC FT Cble Y3 () SPEAKER 3.5 mm stereo plug USER MANUAL pol RJ 45 Con MIC MICE PWR TXD RXD GND Try Stndrd shielded CAT 5 Y3 -pol RJ 45 Con B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 5 of 233

159 RRC-25MkII AUX/MIC MIC FT-57 USER MANUAL SPEAKER 3.5 mm stereo plug -pol RJ 45 Con MIC MICE PWR TXD RXD GND Try Stndrd shielded CAT 5 Y4 Audio Y4b -pol RJ 45 Con :2 YAESU FTM-350 Cbles RRC-25MkII -> Rdio 25 Cble Y4 () SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 59 of 233

160 YAESU FT-700/00/900 Generl Speker AF CON RRC-25MkII The Remoterig system supports the Yesu FT-700/00/900. The technicl solution is the sme s for ll the other rigs with detchble control pnel. You cn remote control the rdio over Internet from the control pnel without ny PC. We simply replce the cble between the control pnel nd the rdio with two RRC-25 units, one t the control pnel nd one t the rdio. When you push the PWR-ON button n udio nd dt connection is estblished between the units nd you control the rdio s you do normlly with the control pnel directly ttched to the rdio. Hrdwre configurtion The FT-700/00/900 is fully supported by the Remoterig RRC-25MkIIs from version 3. Note! Be wre of tht the FT-00 hs bug which cn cuse it to enter kind of locked mode when it loses power, you then need to connect the front pnel direct to the rdio gin to recover. So we recommend using the FT-900 or FT-700 to void this sitution. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 0 of 233

161 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 5 FT-57/00/900 5 FT-57/00/900 SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-25MkIIs B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

162 Connections The cbling is quite simple nd cn be done with simple RJ nd modulr connectors. The wire control cbles re the sme on control nd rdio end. Drwings of the connection cbles cn be found below. Control-RRC: The control cble Y0 should be connected between the Control pnel nd the AUX/MIC connector. The originl microphone should be connected direct to the rdio front pnel s usul. A speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: The control cble Y0 should be connected between the Rdio-RRC AUX/MIC jck nd the Rdio. The speker cble (Y0c) eg. stndrd cble with 3.5 mm mono connectors in both ends should be connected between the rdio nd the Rdio-RRC speker jck. If cble with stereo plugs re used the ring must be connected to GND in the Rdio end otherwise the rdio will not sense tht speker is connected. Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

163 Rdio-RRC SPEAKER jck 3.5 mm stereo plug RRC-25MkII AUX/MIC -pol RJ 45 Con FT-00/900 Front -pol modulr DATA DATA GND PWR V PWR SW MIC DATA DATA GND PWR V PWR SW MIC Y0 Y0 Y0c :2 YAESU FT-00/900 Cble RRC-25MkII FT-00/900 Rdio -pol modulr 2 3 RRC-25MkII AUX/MIC -pol RJ 45 Con Cble Y0 () FT-00/900 SPEAKER jck 3.5 mm stereo plug A stndrd cble with mono plugs cn lso be used. USER MANUAL Note: The schemtic is vlid for ll three models FT-700/00/900. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 3 of 233

164 YAESU FT-97, FT-000 etc. Generl RRC-25MkII supports the YAESU CAT protocol used by lmost every YAESU rdio. Then you hve to use PC-softwre e.g. HmRdioDeLuxe or similr rig control softwre t the control site. All udio nd dt communiction goes true the RRC:s nd you don't need PC t the remote site. Hrdwre configurtion B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 4 of 233

165 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 3 FT-x7, FT-000x 3 FT-x7, FT-000x SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx * No/Yes (ev. for FT-000xx) Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits ** ** COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-25MkIIs, remember tht the bndwidth demnd is doubled. (**) check with the rdio users mnul, some model need 2 stopbits. Connections Drwings of the connection cbles cn be found under ppendix B. Control-RRC: Connect the Remoterig Y5c cble or stndrd RS-232 cble between the PC nd the RRC COM2. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. If you hve microphone with circulr connector you cn use the Remoterig Y5 dpter cble or the ADMY-7, from Yesu or mke one by yourself. The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: From the RRC COM2 connector to the rdios CAT connector (D-sub RS-232) you cn use the Remoterig Yc cble or mke one by yourself (drwing for Yc is provided). The smller rdios in the FT-x7 series do not hve D-sub or RS-232 port; they only hve TTL-port ccessible vi mini-din jck. You cn either buy n dpter cble, D-sub to mini-din, with level converter clled CT-2 from Yesu or you cn mke cble by yourself nd connect it to the RRC TTL connector. Between the RRC AUX/MIC connector nd the rdios microphone jck you cn connect stndrd ptch cble if the rdio hve RJ-45 jck. If the rdio hve circulr microphone jck you cn use the Remoterig Y cble or mke it by yourself (drwings re provided). Mke the cble s short s possible to prevent it from picking up HF. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 5 of 233

166 The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd "off- the-shelf cble with 3.5 mm stereo plugs in both ends. Y5,Y Y5c,Yc B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

167 Front pnel view Mic Inp -pol Circulr GND PTT MIC MICE Y5 screened 20 cm Y5b :2 Generic YAESU Cble RRC-25MkII to Yesu (FT-2000) RRC-25MkII -pol RJ 45 Con GND PTT MIC MICE V UP RRC-25MkII 7 25 Cble Y5 () SPEAKER 3.5 mm stereo plug USER MANUAL PC DSUB- 9pol Femle Y5c COM2 DSUB- 9pol Mle B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 7 of 233

168 RRC-25MkII COM DSUB- 9pol Femle Yc PWR ON indiction :2 Generic YAESU cble RRC-25MkII -> Rdio GND GND Rdio CAT port DSUB- 9pol Femle GND 25 Cble Y () USER MANUAL -pol RJ 45 Con Mic Inp -pol Circulr MIC MIC PTT PTT SPEAKER 3.5 mm stereo plug RRC-25MkII V MICE Y screened m Yb V MICE Front pnel view SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

169 SPEAKER 3.5 mm stereo plug RRC-25MkII AUX/MIC Try Stndrd shielded CAT 5 MIC MICE MICE MIC MIC PTT PTT GND GND Mini-DIN FT-7,57,97 :2 YAESU x7 cble RRC-25MkII -> Rdio FT-7,57,97 -pol RJ 45 Con RX D TX D 25 Cble Y7 () SPEAKER 3.5 mm stereo plug USER MANUAL 7 7 GND GND 3 3 RRC-25MkII TTL -pol modulr GND V 2 RXD TXD AF 3 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 9 of 233

170 YAESU in Generl (FT-2000) Generl RRC-25MkII supports the YAESU CAT protocol used by lmost every YAESU rdio. Then you hve to use PC-softwre e.g. HmRdioDeLuxe or similr rig control softwre t the control site. All udio nd dt communiction goes true the RRC:s nd you don't need PC t the remote site. Hrdwre configurtion Rdio settings (exmple) B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 70 of 233

171 Prmeter Control Rdio Progrm mode 4 Yesu, Kenwood, Elecrft 4 Yesu, Kenwood, Elecrft SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio Dul-RX (*) - Yes Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 Off 0 Off (*) Avilble only in RRC-25MkIIs, remember tht the bndwidth demnd is doubled. Connections Drwings of the connection cbles cn be found below. Control-RRC: Connect the Remoterig Y5c or stndrd RS-232 cble between the PC nd the RRC COM2. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. If you hve microphone with circulr connector you cn use the Remotrig Y5 cble, the ADMY-7, from Yesu or mke one by yourself. The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: From the RRCCOM2 connector to the rdios CAT connector (D-sub RS-232) you cn use the Remoterig Yc cble or mke cble by yourself (drwings re provided). The smller rdios in the FT-x7 series do not hve D-sub or RS-232 port; they only hve TTL-port ccessible vi mini-din jck. You cn either buy n dpter cble, D-sub to mini-din, with level converter clled CT-2 from Yesu or you cn mke cble by yourself nd connect it to the RRC TTL connector. Between the RRC AUX/MIC connector nd the rdios microphone jck you cn connect stndrd ptch cble if the rdio hve RJ-45 jck. If the rdio hve circulr microphone jck you cn use the Remoterig Y cble or mke n dpter cble by yourself (drwings re provided). If you mke the cble by yourself, just cut stndrd FTP (screened) ptch cble nd solder n -pin circulr connector on it. Mke the cble s short s possible to prevent it from picking up HF. The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd off- the-shelf cble with 3.5 mm stereo plugs in both ends. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 7 of 233

172 Y5,Y Y5c,Yc B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 72 of 233

173 Front pnel view Mic Inp -pol Circulr GND PTT MIC MICE Y5 screened 20 cm Y5b :2 Generic YAESU Cble RRC-25MkII to Yesu (FT-2000) RRC-25MkII -pol RJ 45 Con GND PTT MIC MICE V UP RRC-25MkII 7 25 Cble Y5 () SPEAKER 3.5 mm stereo plug USER MANUAL PC DSUB- 9pol Femle Y5c COM2 DSUB- 9pol Mle B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 73 of 233

174 RRC-25MkII COM DSUB- 9pol Femle Yc PWR ON indiction :2 Generic YAESU cble RRC-25MkII -> Rdio GND GND Rdio CAT port DSUB- 9pol Femle GND 25 Cble Y () USER MANUAL -pol RJ 45 Con Mic Inp -pol Circulr MIC MIC PTT PTT SPEAKER 3.5 mm stereo plug RRC-25MkII V MICE Y screened m Yb V MICE Front pnel view SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 74 of 233

175 KENWOOD in Generl Generl RRC-25MkII supports the Kenwood protocol used by lmost every Kenwood rdio. Then you hve to use PC-softwre e.g. HmRdioDeLuxe or similr rig control softwre t the control site. All udio nd dt communiction goes true the RRC:s nd you don t need PC t the remote site. Hrdwre configurtion B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 75 of 233

176 SIP-Connect/disconnect vi MIC UP button: Rdio settings (exmple) Prmeter Control Rdio Progrm mode 4 Yesu, Kenwood, Elecrft 4 Yesu, Kenwood, Elecrft SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 3 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits 0 - Off 0 - Off COM0 prity *) Avilble only in RRC-25MkIIs. Connections Drwings of the connection cbles cn be found under ppendix B. Control-RRC: B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 7 of 233

177 Connect the Remoterig K4c Cble or stndrd RS-232 cble between the PC nd the RRC COM2. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. If you hve microphone with circulr connector you cn use the Remoterig K3 cble, the MJ-, from Kenwood or mke one by yourself (drwings re provided). The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: From the RRC COM2 connector to the rdios CAT connector (D-sub RS-232) you use the Remoterig K5c cble or mke one by yourself (drwings re provided). Between the RRC AUX/MIC connector nd the rdios microphone jck you cn connect stndrd ptch cble if the rdio hve RJ-45 jck. If the rdio hve circulr microphone jck you cn use the Remoterig K2 cble or mke one by yourself (drwings re provided).mke the cble s short s possible to prevent it from picking up HF. The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd "off- the-shelf cble with 3.5 mm stereo plugs in both ends. K4,K5 K4c,K5c B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 77 of 233

178 Front pnel view Mic Inp -pol Circulr GND K4 screened 20 cm K4b :2 Generic Kenwood cble Control -> RRC-25MkII RRC-25MkII -pol RJ 45 Con GND 25 Cble K4 () SPEAKER 3.5 mm stereo plug USER MANUAL UP UP V V PC 7 PTT MICE MIC PTT MICE MIC 7 RRC-25MkII COM2 DSUB- 9pol K4c Femle DSUB- 9pol Mle B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 7 of 233

179 SPEAKER 3.5 mm stereo plug RRC-25MkII -pol RJ 45 Con MIC MICE PTT GND V RRC-25MkII COM2 DSUB- 9pol Femle K5c K5b PWR ON indiction K5 screened m Rdio CAT port DSUB- 9pol Femle 7 :2 Generic Kenwood cble RRC-25MkII -> Rdio GND Mic Inp -pol Circulr MIC MICE PTT GND V Cble K5 () Front pnel view SPEAKER 3.5 mm stereo plug USER MANUAL B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 79 of 233

180 KENWOOD TS-40 Generl The ide of remote controlling TS-40 is simple; it's just to extend the cord between the rdio nd the control pnel using Internet. When you press the power button on the pnel the rdio comes to life t the remote side nd sound nd pnel info flows cross the Internet between the pir of RRC-25MkII:s. The look nd feel of the pnel is the sme s if the pnel ws directly connected to the rdio. Hrdwre configurtion To mke things little bit more complicted Kenwood hve chnged the lyout of the Mic connector during production nd there re two different configurtions. New rdios with seril number from re using Configurtion type nd older rdios with seril number below re using configurtion type 2. Configurtion type : B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 0 of 233

181 Configurtion type 2: Rdio settings (exmple) Prmeter Control Rdio Progrm mode 5 TS40/TM-D70 5 TS40/TM-D70 SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 3 0 Codec inp premp Yes Codec HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off *) Avilble only in RRC-25MkIIs. Connections All necessry signls between the pnel nd the rdio re connected with the wires in the connection cble. In the pckge delivered by Kenwood there is short nd long cble with RJ connectors which cn be used. Convenient for trvelling is tht the speker is lredy present on the bck of the control pnel so there is no need for n extr speker, even if seprte speker gives much better udio. The following signls re represented in the connection cble (-pol modulr): SPK GND - speker ground 2 V power to control pnel (lwys present) 3 GND 4 RDO - seril dt 5700 bps from rdio to pnel B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

182 5 TDO - seril dt 5700 bps from pnel to rdio AF - udio to speker. The short wire cble with RJ connectors supplied by Kenwood should be used between the Rdio nd the Rdio-RRC. The long wire cble with RJ connectors supplied by Kenwood should be used between the Control-RRC nd the control pnel. The short blck CAT- ptch cble ttched with the Remoterig cn be used s mic connection between the Rdio-RRC nd the rdio. If the TS-40 is provided with microphone with RJ-45 connector you cn connect it directly to the AUX/MIC connector on the Control-RRC. Older TS-40 hs circulr pin connector then you hve to use the dpter cble MJ- which ws then supplied by Kenwood s dpter between the Microphone nd the AUX/MIC connector. Connection type Modulr -pol connector: 3 MIC- mic Signl 4 MICE - mic ground 5 PTT GND PTT Connection type 2 Modulr -pol connector: 3 MIC- mic Signl 4 GND PTT 5 PTT MICE - mic ground If you use the wrong configurtion everything will work but the system will be very sensitive for HF (RFI). Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need t lest A. Rdio-RRC: The Rdio-RRC could be powered with seprte Power supply or the sme s the rdio. If you use the Rdio PS mke sure you hve A fuse on the output to the RRC. Do not connect it direct to 20-40A PS the cble will melt if something hppens. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

183 GND DET NR. CNT NAME DIMENSION NOTE CONSTR. DRAWN COPIED CHECKED STAND. OK SCALE REPLACE REPLACED BY MS :2 Kenwood cbles TS-40 Pnel -> RRC-25MkII Seprted Pnel -pol modulr -pol modulr GND GND 2 V V 2 GND GND GND 0923 DRAWING NR DATE Cble K () USER MANUAL AF AF Front pnel view Mic Inp -pol Circulr 2 7 TS-40 Control Pnel PTT MICE MIC Sme s Kenwood MJ- K RRC-25MkII -pol RJ 45 Con MICE RRC 25MkII TTL RDO RDO TDO TDO Kb PTT MIC B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 3 of 233

184 RRC-25MkII AUX/MIC RRC-25MkII TTL :2 Kenwood cbles RRC-25MkII -> TS-40 Rdio Seprted Pnel Mic Inp TS-40 Control Inp TS Cble K0 () USER MANUAL MIC MIC (2) (2) PTT PTT 5 5 GND GND 7 7 AF AF -pol RJ 45 Con -pol modulr MICE GND GND MICE () () (2) (2) MICE Try Stndrd shielded CAT 5 () () () (2) (2) () () (2) For Mic config type (s/n > ) For Mic config type 2 (s/n < ) MICE GND GND V V GND GND RDO RDO TDO TDO -pol RJ 45 Con -pol modulr B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 4 of 233

185 KENWOOD TM-D70 Generl The Kenwood TM-D70 is modern dul bnd FM-trnsceiver with seprte control pnel which is perfect for remote control vi Internet. The ide of remote controlling TM-D70 is simple; it's just to extend the cord between the rdio nd the control pnel using Internet. When you press the power button on the pnel the rdio comes to life t the remote side nd sound nd pnel info flows cross the Internet between the pir of RRC-25MkII:s. The look nd feel of the pnel is the sme s if the pnel ws directly connected to the rdio. Hrdwre configurtion It's very simple to Interfce the TM-D70 for remote control vi the RRC:s. You only need to mke two simple cbles. One from the Control pnel to the Control-RRC nd one from the Rdio-RRC to the Rdio. The stndrd mic (MC-59) provided with the TM-D70 cn be used nd connected directly to the Control-RRC. From Rdio-RRC to Rdio normlly stndrd shielded FTP ptch cble cn be used for the Mic-signls. A stndrd udio cble with /" inch connectors re used for the udio. A speker re lso needed s there is no speker in the Control pnel. All softwre settings re the sme s for TS-40, but the strps re little bit different in the Control-RRC s the MC-59 mic needs V DC feeding. (see drwings below). Remember tht the buttons on the microphone will not work. If you need DTMF use n other Mic with built in DTMF encoder. The MC-59 do not hve it. It's lso possible to progrm DTMF functions to the rdio which will vilble from the Control pnel. Pcket nd APRS functions re not tested, normlly used functions works s in the norml setup. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 5 of 233

186 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 5 TS40/TM-D70 5 TS40/TM-D70 SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 3 0 Codec inp premp Yes Codec HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off *) Avilble only in RRC-25MkIIs. Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need t lest A. Rdio-RRC: The Rdio-RRC could be powered with seprte Power supply or the sme s the rdio. If you use the Rdio PS mke sure you hve A fuse on the output to the RRC. Do not connect it direct to 20-40A PS the cble will melt if something hppens. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

187 :2 Kenwood TM-D70 cbles Control => RRC-25MkII SPEAKER 3.5 mm stereo plug 25 Cble K7 () USER MANUAL Control Pnel TM-D70 RRC-25MkII TTL -pol RJ 45 Con V GND TXD RXD K7 4/-pol modulr B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 7 of 233

188 RRC-25MkII AUX/MIC RRC-25MkII TTL 4/-pol modulr Kc K :2 Kenwood TM-D70 cbles RRC-25MkII -> Rdio Mic Inp TM-D70 Control Inp TM-D70 Rdio 0V GND TXD RXD Cble K () USER MANUAL SPEAKER 3.5 mm stereo plug -pol RJ 45 Con Try Stndrd shielded CAT 5 MIC MIC MICE MICE PTT PTT GND GND Kb -pol RJ 45 Con -pol RJ 45 Con SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 of 233

189 KENWOOD TM-D700 Generl Speker Control Rdio RRC-25MkII RRC-25MkII CON AF MIC Mic The Kenwood TM-D700 is dul bnd FM-trnsceiver with seprte control pnel which is perfect for remote control vi Internet. The ide of remote controlling TM-D700 is simple; it's just to extend the cord between the rdio nd the control pnel using Internet. When you press the power button on the pnel the rdio comes to life t the remote side nd sound nd pnel info flows cross the Internet between the pir of RRC-25MkII:s. The look nd feel of the pnel is the sme s if the pnel ws directly connected to the rdio. Hrdwre configurtion It's very simple to Interfce the TM-D700 for remote control vi the RRC:s. You only need to mke two simple cbles. One from the Control pnel to the Control-RRC nd one from the Rdio-RRC to the Rdio. The stndrd mic (MC-53DM) provided with the TM-D700 cn be used nd connected directly to the Control-RRC. From Rdio-RRC to Rdio normlly stndrd shielded FTP ptch cble cn be used for the Mic-signls. A stndrd udio cble with /" inch connectors re used for the udio. A speker is lso needed s there is no speker in the Control pnel. Remember tht the function buttons on the microphone will not work but. The DTMF buttons re working. The Pcket rdio functions re not tested but the normlly used functions works s in the norml setup. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 9 of 233

190 Rdio settings (exmple) Prmeter Control Rdio Progrm mode TS-2000/TM-D700 TS-2000/TM-D700 SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 3 0 Codec inp premp Yes Codec HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off *) Avilble only in RRC-25MkIIs. Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need t lest A. Rdio-RRC: The Rdio-RRC could be powered with seprte Power supply or the sme s the rdio. If you use the Rdio PS mke sure you hve A fuse on the output to the RRC. Do not connect it direct to 20-40A PS the cble will melt if something hppens. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 90 of 233

191 2 GND GND Control Pnel 4-pol Modulr 4/4 2 4 K3b V K3c V RDO RDO TDO TDO :2 Kenwood cble RC-pnel -> RRC-25MkII RRC-25MkII TTL 4/-pol modulr Cble K3 () SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 9 of 233

192 RRC-25MkII TTL 4/-pol modulr V V :2 Kenwood cble RRC-25MkII -> TM-D700 Control Inp TM-D700 4/-pol modulr 25 Cble K2 () USER MANUAL MIC MIC MICE MICE GND GND SPEAKER 3.5 mm stereo plug -pol RJ 45 Con Try Stndrd shielded CAT 5 PTT PTT GND GND Kc K2b RDO RDO TDO TDO K2c Mic Inp TM-D700 -pol RJ 45 Con SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 92 of 233

193 KENWOOD TS-2000 Generl The technicl solution for TS-2000 is the sme s for TS-40 nd IC-70 with the different tht TS-2000 hs specil control pnel witch works in prllel with the front pnel control on the rdio. If you hve the TS-2000 t your summer QTH you do not need to tke the control pnel with you when you wnt to use the TS-2000 loclly. We replce the cble between pnel nd rdio with to RRC-25, one connected to the control pnel nd one connected to the rdio. When you press the power button on the pnel the rdio comes to life t the remote side nd udio nd pnel info flows cross the internet between the RRC:s. The look nd feel of the control pnel is the sme s if the pnel ws directly connected to the rdio. Hrdwre configurtion B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 93 of 233

194 Rdio settings (exmple) Prmeter Control Rdio Progrm mode TS2000 TS2000 SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) - Yes Codec out gin Codec inp gin 3 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-25MkIIs, remember tht the bndwidth demnd is doubled. Connections The TS-2000 is quite simple to connect becuse you do not need ny specil cble. All necessry signls between the pnel nd the rdio re connected with the 4 wires in the connection cble. We just need to cut it prt nd connect RRC-25MkII in ech end. The following signls re represented in the connection cble (modulr): RJ2 Modulr 4/ Rdio RJxx Modulr 4/4 Control pnel Description 2 V power to control pnel (lwys present) 3 2 GND 4 3 RDO - seril dt 5700 bps from rdio to pnel 5 4 TDO - seril dt 5700 bps from pnel to rdio The esiest wy to mke these two cbles from control pnel to Control-RRC TTL connector nd from Rdio-RRC TTL connector to rdio is to cut the cble supplied by Kenwood into two pieces. You only hve to crimp two new 4/ modulr connectors on the cbles. Don't mke the one between Rdio-RRC nd rdio to long. The long microphone extension cble supplied by Kenwood cn lso be used between Rdio- RRC AUX/MIC connector to the rdio Microphone jck. Probbly you need to cut it lter to prevent it from picking up HF from your ntenns. The microphone cn be connected to the Control-RRC AUX/MIC connector using the dpter cble MJ- supplied by Kenwood with your TS B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 94 of 233

195 The speker supplied with the TS-2000 is connected to the 3.5 mm SP-jck on the front of the Control-RRC. The speker signl from the TS-2000 ext. speker jck to the Rdio-RRC SP jck is connected vi stndrd "off-the-shelf cble with 3.5 mm stereo plugs in both ends. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 95 of 233

196 4 RC-2000 Control Pnel 4-pol Modulr 4/4 :2 Kenwood cble RC > RRC-25MkII RC2000 Pnel 25 Cble K3 () USER MANUAL Front pnel view Mic Inp -pol Circulr GND PTT MICE MIC Sme s Kenwood MJ- K3 K3b V K3c V GND GND RDO RDO TDO TDO RRC-25MkII -pol RJ 45 Con RRC-25MkII TTL 4/-pol modulr 3 5 GND PTT MICE MIC SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 9 of 233

197 RRC-25MkII TTL 4/-pol modulr V V :2 Kenwood cble RRC-25MkII -> TS-2000 RC-2000 Pnel Control Inp TS /-pol modulr Front pnel view Cble K2 () 7 5 USER MANUAL 2 2 GND GND SPEAKER 3.5 mm stereo plug RRC-25MkII -pol RJ 45 Con MIC MICE PTT GND GND K2 K2b RDO RDO TDO TDO K2c Mic Inp -pol Circulr MIC MICE PTT 7 2 SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 97 of 233

198 ELECRAFT K3-Twin Generl RRC-25MkIIs supports the specil high end concept where one Elecrft K3 rdio cn be used to control nother Elecrft K3 rdio. From Jn 202 there is lso specilly designed control rdio clled K3/0 vilble from Elecrft which hs no RF-prts. No PC:s needed t either end. The functionlity is perfect s Elecrft hs dded support in their softwre specilly for this purpose. The control rdio is not used other thn s terminl so it doesn t mtter how it s configured. It cn be the K3/0 or the simplest K3/0 without ny options even if the remote K3 is loded with ll extrs. The RRC-25MkIIs Elecrft Twin pckge includes ll necessry cbles. The boxes do not need to be opened ll strppings re done in production. All you need to do is to put the system together nd do the IP-settings. The ordinry RRC-25MKIIs cn lso be configured to be used for Elecrft K3 twin. Hrdwre configurtion In the stndrd RRC:s the strppings re done mnully by the customer, but In the RRC- 25MkIIs Elecrft K3 Twin pckge the strppings re done by smll pcb mrked 25KE which is ssembled t the strpping re. The smll pcb is removble if you lter wnt to use the RRC:s for some other configurtion. When you replce it is importnt tht the notch which mrks pin one is plced ccording to the picture below. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 9 of 233

199 For your reference the picture below shows how the strppings re done on the smll pcb. JMP should be in plce when using Elecrft MH2 Mic nd removed when using for exmple Heil hedset. Rdio settings (exmple) Prmeter Control Rdio Progrm mode 4 Elecrft K3 twin 4 Elecrft K3 twin SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio Dul-RX - Yes/No (*) Codec out gin Codec inp gin 4 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte 3400 (*2) 3400 (*2) COM0 dt bits B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 99 of 233

200 COM0 stop bits COM0 prity 0 - Off 0 - Off COM2 mode Logicl prllel with COM0 Logicl prllel with COM0 OUT0 - Connect (*) Avilble only in RRC-25MkIIs, remember tht the bndwidth demnd is doubled. (*2) Set the CAT speed in both Rdios lso to 3400 bud. Connections Connections Drwings of the connection cbles cn be found below. All necessry cbles re included in the pckge. Control site B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj of 233

201 Connect 2V power supply to the PWR jck 2 Connecter Ethernet to the Ethernet jck ( 2m CAT 5 cble included) 3 Connect the CAT cble Ed from the RRC COM2 connector to the K3 CAT connector 4 Connect the microphone vi the Microphone dpter cble E 5 Connect speker to the speker jck, If you wnt seprte udio from the sub-rx you need two spekers, the speker for the sub-rx must be ctive. (spekers nd cble re not included) Connect pddle to the PAD jck ( dpter from ¼ connector to 3.5 mm included) Rdio site B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 20 of 233

202 Connect 2V power supply to the PWR jck 2 Connecter Ethernet to the Ethernet jck ( 2m CAT 5 cble included) 3 Connect the CAT cble E2c from the COM2 connector to the K3 CAT connector 4 Connect the mic cble E2 from the AUX/MIC jck to the K3 mic connector. 5 Connect the udio cble from to the SP jck to the K3 speker out on the bck output. Connect the keying cble from the PAD jck to the K3 key input (Adpter from ¼ connector to 3.55 mm included) 7 Connect the K3 remote power on cble E3c from I/O jck to the K3 ACC connector. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj of 233

203 Logging or computer control, RTTY etc. Even if the CAT connector t the Remote K3 is occupied with the communiction between the two K3:s it is possible to connect other equipment to the system due to n intelligent CAT server functionlity in the RRC.s. If you need to connect ntenn switch for exmple which need to tlk to the remote K3 you cn connect it to the Rdio-RRC COM nd configure COM to Mode, CAT to COM2 (locl). If you wnt to connect logging or PC-control softwre to the system you cn connect it to the Control-RRC COM vi RS-232 or USB nd configure both RRC:s COM to Mode-7, CAT to COM2 (locl&remote). Then ll commnds go to nd from the Remote K3 over the network. You cn still use the remote ntenn switch s described bove. Independent of the connections bove you cn use the K3:s FSK trnsmission. Configure Rdio-RRC OUT mode = Budot/45 nd use the Virtul USB port COMFSK for the RTTY softwre. The supplied ACC cble re wired to key the K3 FSK input. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj of 233

204 Cble Ed Control K3 to Control-RRC COM2 9PF-9PF Cble E2c Rdio-RRC COM2 to Remote K3 9PM-9PF Cble E3c I/O to K3 ACC jck Adpter 3.5 mm to ¼ Pddle input dpter to remote rdio Cble E Mic to Control-RRC Mic jck Cble E2 Rdio-RRC Mic jck to K3 Mic input B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj of 233

205 Cble 3.5 mm 3.5 mm Audio Output from Remote rdio to Rdio-RRC SP input jck Cble 3.5 mm 3.5 mm Keyer from Rdio- RRC PAD jck to Remote rdio stright key input jck Adpter ¼ to 3.5 mm Hedset dpter Adpter ¼ to 3.5 mm Pddle dpter B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj of 233

206 Front pnel view Mic Inp -pol Circulr 2 7 K3 Rdio RS-232 portcom2 DSUB- 9pol Mle GND PTT MICE MIC E Eb Ed Elecrft Twin cbles Control K3 to Control-RRC RRC25MkII AUX/MIC Pol RJ45 Con GND PTT MICE MIC RRC25MkII COM2 DSUB- 9pol Mle Cble E () SPEAKER 3.5 mm stereo plug USER MANUAL B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 20 of 233

207 SPEAKER 3.5 mm stereo plug RRC-25MkII COM2 DSUB- 9pol Femle E3c RRC-25MkII AUX/MIC -pol RJ 45 Con E2 E2b E2c Elecrft Twin cbles Rdio-RRC to Remote K3 Rdio RS-232 DSUB- 9pol Mle GND Front pnel view Cble E3 () 7 5 SPEAKER 3.5 mm stereo plug USER MANUAL 5 GND RRC25MkII I/O RJ MIC MICE PTT Rdio ACC port HDDSUB- 5pol VGA type Mle GND GND MIC MICE PTT 7 2 B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj of 233

208 ELECRAFT Generl User ppliction Speker Remote PA CW AF MIC CAT RRC-25MkIIs CW-Pddle Mic The Remoterig system works with both Elecrft K2 nd K3. Hrdwre configurtion JMP should be in plce when using Elecrft MH2 Mic nd removed when using for exmple Heil hedset. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 20 of 233

209 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 4 Yesu, Kenwood, Elecrft 4 Yesu, Kenwood, Elecrft SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio Dul-RX - Yes/No Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-25MkIIs, remember tht the bndwidth demnd is doubled. Connections Control-RRC: Connect stndrd RS-232 cble between the PC nd the RRC COM2. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. If you hve microphone with circulr connector you cn use the Remoterig K4 cble, use the MJ-, from Kenwood or mke one by yourself (drwings re provided). The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: From the RRC COM2 connector to the rdios KIO3 module connector (D-sub RS-232) you use stndrd RS-232 cble. Between the RRC AUX/MIC connector nd the rdios circulr microphone jck you cn use the Remoterig K5 cble or mke n dpter cble by yourself (drwings re provided). Mke the cble s short s possible to prevent it from picking up HF. The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd "off- the-shelf cble with 3.5 mm stereo plugs in both ends. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj of 233

210 E,E2 Ec,E2c B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 20 of 233

211 PC Speker/Hedset Connector DET NR. CNT NAME DIMENSION NOTE CONSTR. DRAWN COPIED CHECKED STAND. OK SCALE REPLACE REPLACED BY MS :2 Generic Elecrft cble Control -> RRC-25MkII RRC-25MkII DRAWING NR DATE Cble E () USER MANUAL Front pnel view Mic Inp -pol Circulr 2 7 GND PTT MICE MIC DSUB- 9pol Femle Sme s Kenwood MJ- E Eb Ec RRC-25MkII -pol RJ 45 Con GND PTT MICE MIC 7 DSUB- 9pol Mle COM2 SPEAKER 3.5 mm stereo plug B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

212 SPEAKER 3.5 mm stereo plug RRC-25MkII -pol RJ 45 Con COM2 DSUB- 9pol Femle MIC MICE PTT GND GND E2 RRC-25MkII E2c E2b :2 Generic Elecrft cble RRC-25MkII -> Rdio Rdio RS-232 port DSUB- 9pol Mle GND Mic Inp -pol Circulr MIC MICE PTT 7 2 Front pnel view Cble E2 () 7 5 SPEAKER 3.5 mm stereo plug USER MANUAL B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 22 of 233

213 ALINCO DX-SR nd DX-R Generl The technicl solution for the trnsceiver Alinco DX-SR nd the receiver DX-R is the sme s for IC-703/70, TS40 nd TS All those trnsceivers re built in the wy tht the control pnel is working seprted from the rdio unit itself. We replce the cble between pnel nd rdio with to RRC-25, one connected to the control pnel nd one connected to the rdio. When you press the power button on the pnel the rdio comes to life t the remote side nd udio nd pnel info flows cross the internet between the RRC:s. The look nd feel of the control pnel is the sme s if the pnel ws directly connected to the rdio. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 23 of 233

214 Hrdwre configurtion Rdio settings (exmple) Prmeter Control Rdio Progrm mode 2 DX-SR 2 DX-SR SIP pssword hello hello SIP contct Auto connect No Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 2 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-25MkIIs. Connections All necessry signls between the pnel nd the rdio re connected with the wires in the connection cble, stndrd ptch cble. We just need to use two stndrd ptch cbles, one between the control pnel nd the Control-RRC nd the other one between the Rdio-RRC nd the rdio. Convenient for trvelling is tht the speker is lredy present on the bck of the control pnel so there is no need for n extr speker even if bigger seprte speker gives better udio. The following signls re represented in the connection cble: TXD - dt from rdio to control pnel 2 RXD - dt from Control pnel to rdio B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 24 of 233

215 3 V - power to control pnel (when rdio is switched on) 4 Not in use 5 Mic signl / PWR on/off button GND 7 AF - Audio to speker. SPK GND - Speker ground Power supply Control-RRC: The Control-RRC is supplied with common 3. V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need t lest A. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 25 of 233

216 RRC-25MkII with 2-wire or 4-wire interfces Generl Control Rdio RRC-25MkII RRC-25MkII The RRC versions with 2-wire nd 4-wire interfces re minly used for remote control of commercil rdio systems which ws designed for lesed 2 or 4 wire lines. The interfces re blnced nd re using trnsformers for isoltion nominl impednce is 00 ohm resistive. The 4-wire version cn be order with opto couplers for trnsfer of E nd M signls. Nominl udio level is -0 dbm nd mx level is bout +4 dbm. The system lso supports trnsfer of two independent seril ports. Hrdwre configurtion The Interfce PCB for 2 nd 4-wires must be instlled t fctory. No other strppings needed. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

217 Rdio settings (exmple) Prmeter Control Rdio Progrm mode Trnsprent 4-wire Trnsprent 4-wire SIP pssword hello hello SIP contct Auto connect Yes Audio qulity 2 Liner bits khz 2 Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 4 (4w)/2 (2w) 4 (4w) /2 (2w) Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Not pplicble. Connections Pin no 2-wire Interfce 4-wire Interfce AUX (RJ45) AUX (RJ45) E-In [-]* 2 M-Out* 3 4-wire in [b] 4 2-wire [] 4-wire out [] 5 2-wire [b] 4-wire out [b] 4-wire in [b] 7 M-Out* E-In [+]* (*) E/M support hve to be ordered seprte. Power supply Control-RRC: The Control-RRC is supplied with common 3. V (0-V) A power supply. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 27 of 233

218 Schemtics I/O nd PAD interfce B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 2 of 233

219 MIC/AUX Interfce Control-RRC MkII B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 29 of 233

220 Speker output interfce Control-RRC MkIIs Speker input interfce Rdio-RRC MkIIs B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj of 233

221 MIC/AUX Interfce Rdio-RRC B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj 2 22 of 233

222 Networks nd Firewlls One of the mjor obstcles when trying to remotely control something is the fct tht the Internet Service Provider (ISP) forces us to use dynmic IP ddresses. We cn never know, from time to time, which IP ddress our modem / firewll / router hs on its outside interfce (the IP ddress you will try to connect to). Most people use NAT routers tht trnsltes IP ddresses on the inside (your little LAN) to one common IP ddress on the outside using port conversion. To be ble to strem udio nd t the sme time trnsfer CAT / CI-V commnds or pnel-tordio communictions' we need to know which IP port numbers re used for ech service. There re some different techniques to fix this. At the opertor end (Control-RRC) there is normlly OK just to use DHCP for the own IPsettings. For the Sip contct prmeter you enter the public fixed IP ddress or Dynmic DNS-nme to the router t the rdio site. At the rdio end (Rdio-RRC) the router must be configured so tht port 3000, 300, 3002 nd 0 (defult settings) re directed to the Rdio-RRC which should hve sttic IP ddress. The esy wy to get connected is to set the RRC IP ddress s DMZ server in the router. This mkes it possible to connect to ll services (SIP, udio nd control) s well s the web nd telnet interfces without further configurtion. If you run web server t the rdio site you need to chnge the webserver port from 0 to something else, for exmple 000. Port 0 cn lso be blocked by the ISP. If you re using port forwrding you hve to configure the router in wy tht every service forwrds pckets to the right host on the inside. When setting up the router check tht there is No SIP ALG ctivted. You will lso need to register the Rdio-RRC to Dynmic DNS Service so you cn use host nme to connect to the Rdio-RRC regrdless of its dynmic IP ddress (which cn chnge without notice, but rrely does). The following defult IP ports re used (chngeble) port number Protocol function 3000 UDP SIP (chnge this port number in both ends if you re using SIP bsed IP-telephony) 300 UDP RTP, udio 3002 UDP DATA chnnel, control commnds 0 TCP WEB interfce 23 TCP Telnet Interfce In erlier firmwres, other defult ports where used (eg 2000,000,500,0,23) B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj of 233

223 DMZ A typicl setup screen for ctivting DMZ is shown below. Enter the IP-number of the Rdio-RRC in box nd enble DMZ. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj of 233

224 Portforwrding A typicl setup screen for ctivting port forwrding is shown below. There is one row ssigned for ech port (service) ll refereeing to the IP of the Rdio-RRC B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj of 233

225 SIP ALG If the router hs prmeter clled SIP ALG it should lwys be Disbled in both the Control nd rdio end. B25B_RemoteRig_MkIIs-A29 User mnul Rev. A Mj of 233