Section 5.2, Commands for Configuring ISDN Protocols. Section 5.3, Configuring ISDN Signaling. Section 5.4, Configuring ISDN LAPD and Call Control
|
|
- Nathan York
- 8 years ago
- Views:
Transcription
1 Chpter 5 Configurtion of ISDN Protocols This chpter provides instructions for configuring the ISDN protocols in the SP201 for signling conversion. Use the sections tht reflect the softwre you re configuring. Before configuring the protocols for your SP201, e sure you hve completed ll the configurtion procedures in Chpter 2, Configurtion Overview. The following susections contin informtion on configuring ISDN protocols in the SP201: Section 5.1, ISDN in the SP201 Section 5.2, Commnds for Configuring ISDN Protocols Section 5.3, Configuring ISDN Signling Section 5.4, Configuring ISDN LAPD nd Cll Control Section 5.5, The ISDN Rte Converter
2 5-2 Chpter 5: Configurtion of ISDN Protocols 5.1 ISDN in the SP201 An integrted services digitl network (ISDN) provides high-speed end-toend digitl service over existing telecommunictions networks, including copper-wire telephone lines used in most homes. ISDN llows single highspeed interfce to provide severl services, such s telephone (voice), fx, computer (dt), nd video trnsmission. ISDN supports trnsmission t 64 kps on ech chnnel. The SP201 supports the following vrints of ISDN: Ntionl ISDN version 2 (NI2), used primrily in North Americ Europen Telecommunictions Stndrds Institute (ETSI) ISDN, used in most plces outside North Americ ETSI ISDN nd NI2 ISDN systems vry s follows: NI2 supports the T1 rte (1.544 Mps: 24 chnnels t 64 kps per chnnel). In NI2, timeslot 24 is used for the D-chnnel. ETSI supports the E1 rte (2.048 Mps: 31 chnnels t 64 kps per chnnel). In ETSI, timeslot 16 is used for the D-chnnel. The ISDN protocols implemented in the SP201 conform to the following stndrds: ETSI ISDN conforms to ETSI nd to ITU-T Recommendtions Q.931 nd Q.921. NI2 ISDN conforms to BellCore TR-NWT nd TR-NWT nd to ITU-T Recommendtions Q.931 nd Q.921. Both vrints of ISDN used in the SP201 re configured in the sme mnner. Any differences occur in options for prmeters; ech vrint will present its own options. Where pproprite, steps in procedures will point out ny differences for the vrints. The ISDN protocol uses out-of-nd signling. Ech stndrd ISDN trunk hs one signling chnnel (D-chnnel); the trunk s remining chnnels re erer chnnels (B-chnnels). A T1 line hs 23 B-chnnels; n E1 line hs 30 B-chnnels. On T1 lines, timeslot 24 is usully the D-chnnel; on E1 lines, timeslot 16 must e the D-chnnel. The ISDN protocols supported in the SP201 use the ISDN Primry Rte Interfce (PRI, for crrying dt nd voice over the B-chnnels) Sometimes the SP201 softwre uses the term PRI to indicte ISDN prmeters.
3 Commnds for Configuring ISDN Protocols Commnds for Configuring ISDN Protocols Tle 5-1 descries the commnds used for configuring ISDN protocols in the SP201. Tle 5-1. ISDN Protocol Configurtion Commnds Commnd Nme Protocol Description config cc utolock config cc cgptynum config cc chrgeind config cc diltone config cc forcecm config cc numer config cc overlp config cc useruserinfo ETSI ISDN, NI2 ISDN NI2 ISDN (to SS7) NI2 ISDN (to SS7) ETSI ISDN ETSI ISDN (to SS7), NI2 ISDN (to SS7) ETSI ISDN (to SS7), NI2 ISDN (to SS7) ETSI ISDN NI2 ISDN (to SS7) Enle or disles utomtic locking of SS7 ISUP circuits, ccording to the stte of the ISDN D-chnnel. See Section , The config cc utolock Commnd. Indictes whether to trnsmit clling prty informtion. See Section , The config cc cgptynum Commnd. Indictes whether to include CHARGE nd CALLED PARTY CAT indiction in the ACM messge. See Section , The config cc chrgeind Commnd. Indictes whether to generte dil tone for the cller. See Section , The config cc diltone Commnd. Indictes whether to support forced ACM. See Section , The config cc forcecm Commnd. Configures mpping of SS7 Nture of Address, ISDN Type of Numer, nd Numering Pln fields in Clled Prty Numer nd Clling Prty Numer Informtion Elements. See Section , The config cc numer Commnd. Indictes whether to llow overlp diling. See Section , The config cc overlp Commnd. Indictes whether to include user-to-user informtion element in the ISDN setup messge. See Section , The config cc useruserinfo Commnd. config dchns ll ISDN Configures ISDN signling chnnels (D-chnnels) to meet instlltion requirements. Configurtion of D-chnnels vries slightly y type of ISDN; it differs sustntilly for stndrd ISDN chnnels nd undled (fcility) ISDN chnnels. See Section 5.3, Configuring ISDN Signling.
4 5-4 Chpter 5: Configurtion of ISDN Protocols ISDN trunks re on the SP201 s physicl (hrdwre) ports 5 8. (To verify the ports for ISDN trunks, use the show dchns commnd, descried in Section , The show dchns Commnd.) Ech ISDN trunk lso hs n interfce (softwre) ID in the configurtion commnds. The IDs for current ISDN commnds conform to the physicl port numers. The interfce IDs in legcy ISDN commnds strt with trunk vlue 1. In the ISDN deug commnds (config q931 nd config lpd), the profile numers (sometimes clled element numers) nd interfce IDs strt with trunk vlue 0. Tle 5-2 lists ech physicl trunk on the SP201, its ISDN trunk numer, nd its interfce IDs for ISDN legcy nd deug commnds. Tle 5-2. SP201 ISDN Trunks nd Corresponding ISDN Interfce Numers SP201 s Physicl Port ISDN Trunk Interfce ID for Legcy ISDN Commnds Profile Numer nd Interfce ID for ISDN Deug Commnds Configuring ISDN Signling This section contins instructions for configuring the signling timeslot (the D-chnnel) for ISDN trunks on the SP201. See the following sections: Section 5.3.1, Stndrd ISDN Signling Section 5.3.2, Network Fcility Associted Signling Stndrd ISDN Signling This document uses the term stndrd ISDN trunk to indicte stndlone ISDN trunk tht is, n ISDN trunk tht is not prt of fcility. (An ISDN fcility undles two or more ISDN trunks into one entity.)
5 Configuring ISDN Signling 5-5 Ech stndrd ISDN trunk hs one signling chnnel (D-chnnel). On T1 lines, timeslot 24 is usully the D-chnnel; on E1 lines, timeslot 16 must e the D-chnnel The config dchns Commnd for Stndrd ISDN Trunks You use the config dchns commnd to configure signling chnnels (D-chnnels) for ISDN trunks. Figure 5-1 shows the tsk flow for the config dchns commnd when configuring stndrd ISDN trunks. Follow the procedure elow to configure D-chnnel for ech ISDN trunk on the SP201. Figure 5-1. Tsk Flow for the config dchns Commnd for Stndrd ISDN Trunk See one of the following to configure stndrd ISDN trunks: To configure n ETSI ISDN trunk, see How to Use the config dchns Commnd for Stndrd ETSI ISDN Trunk. To configure stndrd Ntionl ISDN trunk, see How to Use the config dchns Commnd for Stndrd Ntionl ISDN Trunk. Note: To configure Ntionl ISDN trunks s fcility, see Section 5.3.2, Network Fcility Associted Signling.
6 5-6 Chpter 5: Configurtion of ISDN Protocols How to Use the config dchns Commnd for Stndrd ETSI ISDN Trunk 1 At the user> prompt, type config dchns nd press Enter. Informtion similr to the following ppers. user> config dchns The following is the present Trunk configurtion. If chnge to the Timeslot or Interfce Type is desired Enter the Trunk numer you wish to modify or exit: ****************************************************************************** *************************** ISDN D-CHANNEL STATUS **************************** ****************************************************************************** Trunk FAS/ Signling Interfce Time # of D-Chnnel Trunk Type Protocol NFAS Type Type Slot Filures Sttus ****************************************************************************** 5 E1 ETSI ISDN FAS D-Chnnel Network Inctive 6 E1 ETSI ISDN FAS D-Chnnel Network Inctive 7 E1 ETSI ISDN FAS D-Chnnel Network Inctive 8 E1 ETSI ISDN FAS D-Chnnel Network Inctive ****************************************************************************** ISDN Trunk Numer Enter vlue([5-8]) or "exit" : 2 Do one of the following: If the ISDN trunk configurtion is pproprite for your network, type exit nd press Enter. The user> prompt reppers. user> If you wish to chnge informtion for trunk, type the trunk numer (where trunk 5 identifies the ISDN trunk on port 5) nd press Enter. The following prompt ppers.
7 Configuring ISDN Signling 5-7 Select interfce type - user(0) or network(1) : <current=1> 3 Indicte the role the SP201 will ply in the ISDN connection. Type 0 for User or 1 for Network, nd press Enter. The following prompt ppers. ISDN Interfce numer 1 ssigned to Trunk 5, with D Chnnel on timeslot 16. Chnge ISDN Signling Chnnel Enter vlue(1-31; current="16") or "exit" : 4 Type the numer of the timeslot tht will e the signling chnnel for this trunk, nd press Enter. Note: E1 trunks must use timeslot 16 s the signling chnnel. T1 trunks usully use timeslot 24 s the signling chnnel. One of the following results occurs: If you chnged nothing, the user> prompt ppers. Go to Step 6. If you chnged ny of the configurtion, the following messge ppers. The crd must e reset for the chnges to operte properly Do you wish to reset now (y/n)? 5 Do one of the following: If you hve other ISDN trunks to configure, type n nd press Enter. The user> prompt is displyed.
8 5-8 Chpter 5: Configurtion of ISDN Protocols user> If you hve no other ISDN trunks to configure, type y nd press Enter. The SP201 performs wrmstrt. When it hs finished, the user> prompt is displyed. 6 If you wish to chnge informtion for nother ISDN trunk, perform Step 1 through Step 5 gin. Note: If you nswered no in Step 5 to ny trunk tht sked you to reset, you must wrmstrt the SP201 so tht the chnges will e implemented. See Section 3.4.1, The wrmstrt Commnd. How to Use the config dchns Commnd for Stndrd Ntionl ISDN Trunk 1 At the user> prompt, type config dchns nd press Enter. The following question ppers. Is this n NFAS interfce? (y or n) : <current=n> 2 Type n nd press Enter. Note: If you do wish to configure n NFAS (fcility) interfce, see How to Use the config dchns Commnd for n ISDN Fcility. Informtion similr to the following ppers.
9 Configuring ISDN Signling 5-9 The following is the present Trunk configurtion. If chnge to the Timeslot or Interfce Type is desired Enter the Trunk numer you wish to modify or exit: ****************************************************************************** *************************** ISDN D-CHANNEL STATUS **************************** ****************************************************************************** Trunk FAS/ Signling Interfce Time # of D-Chnnel Trunk Type Protocol NFAS Type Type Slot Filures Sttus ****************************************************************************** 5 T1 NI2 ISDN FAS D-Chnnel Network Inctive 6 T1 NI2 ISDN FAS D-Chnnel Network Inctive 7 T1 NI2 ISDN FAS D-Chnnel Network Inctive 8 T1 NI2 ISDN FAS D-Chnnel Network Inctive ****************************************************************************** ISDN Trunk Numer Enter vlue([5-8]) or "exit" : 3 Do one of the following: If the ISDN trunk configurtion is pproprite for your network, type exit nd press Enter. The user> prompt reppers. user> If you wish to chnge informtion for trunk, type the trunk numer (where trunk 5 identifies the ISDN trunk on port 5) nd press Enter. The following prompt ppers. Select interfce type - user(0) or network(1) : <current=1> 4 Indicte the role the SP201 will ply in the ISDN connection. Type 0 for User or 1 for Network, nd press Enter. The following prompt ppers.
10 5-10 Chpter 5: Configurtion of ISDN Protocols ISDN Interfce numer 1 ssigned to Trunk 5, with D Chnnel on timeslot 24. ISDN Interfce Type [d] D Chnnel [n] NFAS Chnnel [] Active D Chnnel [exit] Exit Enter selection(current="d Chnnel") : Note: Becuse this is stndrd ISDN trunk, the softwre selects the stndrd D Chnnel for the signling chnnel type. The other choices re for signling types used in fcilities. (An ISDN fcility undles two or more ISDN trunks, using only one signling chnnel for the erer chnnels on ll the undled trunks. See Section 5.3.2, Network Fcility Associted Signling.) 5 Select D Chnnel nd press Enter. The following prompt ppers. D Chnnel Time Slot Enter vlue(1-31; current="24") or "exit" : 6 Type the numer of the timeslot tht will e the signling chnnel for this trunk, nd press Enter. Note: E1 trunks must use timeslot 16 s the signling chnnel. T1 trunks usully use timeslot 24 s the signling chnnel. One of the following results occurs: If you chnged nothing, the user> prompt ppers. Go to Step 8.
11 Configuring ISDN Signling 5-11 If you chnged ny of the configurtion, the following messge ppers. The crd must e reset for the chnges to operte properly Do you wish to reset now (y/n)? 7 Do one of the following: If you hve other ISDN trunks to configure, type n nd press Enter. The user> prompt is displyed. user> If you hve no other ISDN trunks to configure, type y nd press Enter. The SP201 performs wrmstrt. When it hs finished, the user> prompt is displyed. 8 If you wish to chnge informtion for nother ISDN trunk, perform Step 1 through Step 7 gin. Note: If you nswered no in Step 7 to ny trunk tht sked you to reset, you must wrmstrt the SP201 so tht the chnges will e implemented. See Section 3.4.1, The wrmstrt Commnd Network Fcility Associted Signling Note: Fcilities re ville only in NI2 ISDN. ETSI ISDN does not support fcilities. Ech stndrd, stndlone ISDN trunk hs one signling chnnel (D-chnnel). However, in Ntionl ISDN you cn undle the SP201 s four
12 5-12 Chpter 5: Configurtion of ISDN Protocols ISDN trunks into one fcility. This llows the four trunks to hndle trffic s one entity; one D-chnnel crries the signling for ll ISDN trunks in the fcility. This llows the timeslots tht would normlly e D-chnnels on the other trunks to function s B-chnnels, incresing the trffic tht the trunks cn crry. In the SP201, you cn undle four ISDN trunks into fcility, freeing up three D-chnnels to function s B-chnnels. An dditionl enefit is tht you cn set ckup D-chnnel for fcility so tht, if the ctive D-chnnel goes out of service, signling is trnsferred to the ckup D-chnnel. (On stndrd, stndlone ISDN trunks, there is no ckup D-chnnel.) A fcility s ckup D-chnnel is lwys redy to ssume signling responsiilities if the ctive D-chnnel goes out of service. The ckup D-chnnel does not crry trffic of ny kind while the ctive D-chnnel is in service, so tht the ckup D-chnnel will not hve to wit for other trffic to disperse efore it ssumes the signling function. Note: All trunks in fcility must connect to the sme remote device, nd the remote device must hve the trunks configured s fcility, s well The config dchns Commnd for ISDN Fcilities You cn use the config dchns commnd to configure signling chnnels (D-chnnels) for fcility of ISDN trunks. Follow the procedure elow to configure D-chnnel for Ntionl ISDN fcility on the SP201. Note: To configure stndrd, non-undled ISDN trunks, see Section 5.3.1, Stndrd ISDN Signling. How to Use the config dchns Commnd for n ISDN Fcility Note: Only Ntionl ISDN supports fcilities. ETSI ISDN does not support fcilities. 1 At the user> prompt, type config dchns nd press Enter.
13 Configuring ISDN Signling 5-13 The following question ppers. Is this n NFAS interfce? (y or n) : <current=n> 2 Type y nd press Enter. Note: If you wish to configure stndrd ISDN trunk, see How to Use the config dchns Commnd for Stndrd Ntionl ISDN Trunk. The following question is displyed. ISDN Trunk Numer for NFAS Signling Enter vlue(5-8) or "exit" : 3 Type the numer of the ISDN trunk tht holds the signling timeslot, nd press Enter. Note: Trunk 5 should lwys e the trunk tht holds the signling timeslot. If you wish to choose otherwise, consult your Encore Networks representtive. Informtion similr to the following ppers.
14 5-14 Chpter 5: Configurtion of ISDN Protocols The following is the present Trunk configurtion. If chnge to the Timeslot or Interfce Type is desired Enter the Trunk numer you wish to modify or exit: ****************************************************************************** *************************** ISDN D-CHANNEL STATUS **************************** ****************************************************************************** Trunk FAS/ Signling Interfce Time # of D-Chnnel Trunk Type Protocol NFAS Type Type Slot Filures Sttus ****************************************************************************** 5 T1 NI2 ISDN NFAS Active D-chn Network Inctive 6 T1 NI2 ISDN NFAS 7 T1 NI2 ISDN NFAS 8 T1 NI2 ISDN NFAS ****************************************************************************** ISDN Trunk Numer Enter vlue([5-8]) or "exit" : 4 Do one of the following: If the ISDN trunk configurtion is pproprite for your network, type exit nd press Enter. The user> prompt reppers. user> If you wish to chnge informtion for trunk, type the trunk numer (where trunk 5 identifies the ISDN trunk on port 5) nd press Enter. The following prompt ppers. Select interfce type - user(0) or network(1) : <current=1> 5 Indicte the role the SP201 will ply in the ISDN connection. Type 0 for User or 1 for Network, nd press Enter. The following prompt ppers.
15 Configuring ISDN Signling 5-15 ISDN Interfce numer 1 ssigned to Trunk 5, with n Active D Chnnel on timeslot 24. ISDN Interfce Type [d] D Chnnel [n] NFAS Chnnel [] Active D Chnnel [exit] Exit Enter selection(current="active D Chnnel") : Note: The ISDN fcility s signling chnnel must use the interfce type Active D Chnnel. 6 Select Active D Chnnel nd press Enter. The following prompt ppers. D Chnnel Time Slot Enter vlue(1-31; current="24") or "exit" : 7 Type the numer of the timeslot tht will e the signling chnnel for this trunk, nd press Enter. Note: E1 trunks must use timeslot 16 s the signling chnnel. T1 trunks usully use timeslot 24 s the signling chnnel. One of the following results occurs: If you chnged nothing, the user> prompt ppers. Go to Step 9. If you chnged ny of the configurtion, the following messge ppers.
16 5-16 Chpter 5: Configurtion of ISDN Protocols The crd must e reset for the chnges to operte properly Do you wish to reset now (y/n)? 8 Do one of the following: If you hve other ISDN trunks to configure, type n nd press Enter. The user> prompt is displyed. user> If you hve no other ISDN trunks to configure, type y nd press Enter. The SP201 performs wrmstrt. When it hs finished, the user> prompt is displyed. 9 If you wish to chnge informtion for nother ISDN trunk, perform Step 1 through Step 8 gin. Note: If you nswered no in Step 8 to ny trunk tht sked you to reset, you must wrmstrt the SP201 so tht the chnges will e implemented. See Section 3.4.1, The wrmstrt Commnd. 5.4 Configuring ISDN LAPD nd Cll Control See the following for discussion of configurtion of cll control prmeters: Section 5.4.1, SS7 ISDN Cll Control SS7 ISDN Cll Control If the SP201 performs protocol conversion etween SS7 nd ISDN, you cn configure SS7 ISDN cll control options s descried in the following
17 Configuring ISDN LAPD nd Cll Control 5-17 sections. (Some config cc commnds re ville only in ETSI ISDN or only in NI2 ISDN. Some config cc commnds re ville in oth types of ISDN.) Section , The config cc utolock Commnd Section , The config cc cgptynum Commnd Section , The config cc chrgeind Commnd Section , The config cc diltone Commnd Section , The config cc forcecm Commnd Section , The config cc numer Commnd Section , The config cc overlp Commnd Section , The config cc useruserinfo Commnd The config cc utolock Commnd When enled, this commnd utomticlly locks nd unlocks SS7 ISUP circuits ccording to the stte of the ISDN signling chnnel. How to Use the config cc utolock Commnd 1 At the user> prompt, type config cc utolock nd press Enter. The following prompt ppers. Do you wnt to support locking/unlocking of ISUP circuits whenever the ISDN D-chnnel goes ctive/inctive? (y/n, current=y) : 2 Do one of the following: If you wnt to lock SS7 ISUP circuits when the ISDN signling chnnel is inctive nd unlock them when the ISDN signling chnnel is ctive, nswer y nd press Enter. Automtic locking is set, nd the user> prompt re-ppers.
18 5-18 Chpter 5: Configurtion of ISDN Protocols If you do not wnt to use utomtic locking of ISUP circuits, nswer n nd press Enter. Automtic locking is disled, nd the user> prompt reppers The config cc cgptynum Commnd This commnd indictes whether to trnsmit clling prty informtion to the clled numer. How to Use the config cc cgptynum Commnd 1 At the user> prompt, type config cc cgptynum nd press Enter. The following prompt ppers. Do you wnt to trnsmit the clling prty informtion from the SS7 side to the ISDN side (y/n, current=n) : 2 Answer y or n nd press Enter. The following prompt ppers. Do you wnt to trnsmit the clling prty informtion from the ISDN side to the SS7 side (y/n, current=n) : 3 Answer y or n nd press Enter. The user> prompt re-ppers The config cc chrgeind Commnd This commnd indictes whether to include CHARGE nd CALLED PARTY CAT indiction in the ACM messge.
19 Configuring ISDN LAPD nd Cll Control 5-19 How to Use the config cc chrgeind Commnd 1 At the user> prompt, type config cc chrgeind nd press Enter. The following prompt ppers. Allow CHARGE nd CALLED PARTY CAT indiction in ACM messge (y/n, current=y) : 2 Answer y or n nd press Enter. The user> prompt re-ppers The config cc diltone Commnd This commnd indictes whether to generte dil tone to the cller. How to Use the config cc diltone Commnd 1 At the user> prompt, type config cc diltone nd press Enter. The following messge ppers. Dil tone is to e generted etween the strt of overlp diling nd the receipt of the first digit, for: Network D-chnnels? (y/n, current=y) : 2 Indicte whether to generte dil tone for signling chnnels when the SP201 is the Network side of the connection. Note: You define whether the SP201 is the Network or User side of the ISDN connection when you configure ISDN. See Section 5.3, Configuring ISDN Signling.
20 5-20 Chpter 5: Configurtion of ISDN Protocols The following prompt ppers: User D-chnnels? (y/n, current=y) : 3 Indicte whether to generte dil tone for signling chnnels when the SP201 is the User side of the connection. The user> prompt is re-displyed The config cc forcecm Commnd This commnd indictes whether to support forced ACM. If you indicte to support forced ACM, n ACM will precede the trnsmission of n ANM when CONN messge is received in the sence of n ALERT messge. Otherwise, n ANM messge will e sent when the CONN is received. How to Use the config cc forcecm Commnd 1 At the user> prompt, type config cc forcecm nd press Enter. The following messge ppers. user> config cc forcecm Do you wnt to support forced ACM for CONN with no ALERT (y/n, current=n) : 2 Indicte whether to support forced ACM, nd press Enter. If you enter y, n ACM will precede the trnsmission of n ANM when CONN messge is received in the sence of n ALERT messge. If you enter n, n ANM messge will e sent when the CONN is received. In either cse, the user> prompt is displyed.
21 Configuring ISDN LAPD nd Cll Control The config cc numer Commnd This commnd configures mpping for the following fields in the Clled Prty Numer nd Clling Prty Numer informtion elements: ISDN Type of Numer ISDN Numering Pln SS7 Nture of Address SS7 Numering Pln How to Use the config cc numer Commnd Note: The options tht pper for ech informtion element depend on the type of ISDN the SP201 uses. The exmples shown here re for ETSI ISDN. 1 At the user> prompt, type config cc numer nd press Enter. The following messge ppers. Do you wnt to mnully mp Clled nd Clling Prty Numer Nture of Address Ind. from SS7 going to ISDN Type of Numer (y/n, current=n) : 2 Do one of the following: If you do not wnt to mnully mp the SS7 Nture of Address for the clled nd clling prty numers, type n nd press Enter. The following prompt ppers. Go to Step 5. Do you wnt to mnully mp Clled nd Clling Prty Numer Numering Pln from SS7 going to ISDN Numering Pln (y/n, current=n) :
22 5-22 Chpter 5: Configurtion of ISDN Protocols If you wnt to mnully mp the SS7 Nture of Address for the clled nd clling prty numers, type y nd press Enter. The SS7 Nture of Address menu ppers. Note: The types of items (nd, consequently, the numer of items) on this menu depend on the type of ISDN instlled on this SP201. Incoming SS7 Outgoing ISDN Numer Nture of Address Type of Numer Unknown --> Ntionl 2 Suscrier numer --> Suscrier Numer 3 Ntionl Numer --> Ntionl 4 Interntionl Numer --> Interntionl 5 Suscr #, op rqsted --> Ntionl 6 Ntl #, op rqsted --> Ntionl 7 Intntl #, op rqsted --> Ntionl 8 No #, op rqsted --> Ntionl 9 No #, cll crrier --> Ntionl cll --> Ntionl 11 Test line test code --> Ntionl 12 QUIT Enter the numer of the prmeter you wish to chnge (1-12): 3 Do one of the following: To exit the SS7 Nture of Address menu, type the line numer for QUIT (12 in this exmple), nd press Enter. (Or just press Enter without typing nything.) The following prompt ppers. Go to Step 5. Do you wnt to mnully mp Clled nd Clling Prty Numer Numering Pln from SS7 going to ISDN Numering Pln (y/n, current=n) : Type the line numer of the Incoming SS7 Nture of Address item you wish to chnge, nd press Enter.
23 Configuring ISDN LAPD nd Cll Control 5-23 An item menu similr to the following ppers, where x represents the Incoming SS7 Nture of Address item whose line numer you selected. (The outgoing options depend on permissile Outgoing ISDN Type of Numer vlues for Incoming SS7 Nture of Address item x.) Trnslte incoming "x" to outgoing vlue: 1 Unknown 2 Interntionl 3 Ntionl 4 Network Specific 5 Suscrier Numer 6 Arevited Numer 7 Reserved-extension 8 QUIT Enter the numer you wish to mp the prmeter to (1-8): 4 Do one of the following: To exit the item menu without chnging Incoming item x s outgoing option, do not type nything. Just press Enter. The SS7 Nture of Address menu re-ppers. Go to Step 3. Type the line numer for the outgoing vlue you wish the Incoming item x to use, nd press Enter. The outgoing vlue for incoming item x is chnged, nd the SS7 Nture of Address menu re-ppers. Go to Step 3. c To exit the SS7 Nture of Address menu system, type the line numer for QUIT (8 in this exmple), nd press Enter. The SS7 Nture of Address menu system termintes, nd the following prompt ppers. Continue to Step 5. Do you wnt to mnully mp Clled nd Clling Prty Numer Numering Pln from SS7 going to ISDN Numering Pln (y/n, current=n) : 5 Do one of the following:
24 5-24 Chpter 5: Configurtion of ISDN Protocols If you do not wnt to mnully mp the SS7 Numering Pln for the clled nd clling prty numers, type n nd press Enter. The following prompt ppers. Go to Step 8. Do you wnt to mnully mp Clled nd Clling Prty Numer Type of Numer from ISDN going to the SS7 Nture of Address Ind. (y/n, current=n) : If you wnt to mnully mp the SS7 Numering Pln for the clled nd clling prty numers, type y nd press Enter. The SS7 Numering Pln menu ppers. Note: The types of items (nd, consequently, the numer of items) on this menu depend on the type of ISDN instlled on this SP201. Incoming SS7 Outgoing ISDN Numer Numering Pln Numering Pln Unknown --> ISDN/telephony num 2 ISDN/telephony num --> ISDN/telephony num 3 privte numering --> ISDN/telephony num 4 QUIT Enter the numer of the prmeter you wish to chnge (1-4): 6 Do one of the following: To exit the SS7 Numering Pln menu, type the line numer for QUIT (4 in this exmple), nd press Enter. (Or just press Enter without typing nything.) The following prompt ppers. Go to Step 8.
25 Configuring ISDN LAPD nd Cll Control 5-25 Do you wnt to mnully mp Clled nd Clling Prty Numer Type of Numer from ISDN going to the SS7 Nture of Address Ind. (y/n, current=n) : Type the line numer of the Incoming SS7 Numering Pln item you wish to chnge, nd press Enter. An item menu similr to the following ppers, where x represents the Incoming SS7 Numering Pln item whose line numer you selected. (The outgoing options depend on permissile Outgoing ISDN Numering Pln vlues for Incoming SS7 Numering Pln item x.) Trnslte incoming "x" to outgoing vlue: 1 Unknown 2 ISDN/telephony num 3 QUIT Enter the numer you wish to mp the prmeter to (1-3): 7 Do one of the following: To exit the item menu without chnging Incoming item x s outgoing option, do not type nything. Just press Enter. The SS7 Numering Pln menu re-ppers. Go to Step 6. Type the line numer for the outgoing vlue you wish the Incoming item x to use, nd press Enter. The outgoing vlue for incoming item x is chnged, nd the SS7 Numering Pln menu re-ppers. Go to Step 6. c To exit the SS7 Numering Pln menu system, type the line numer for QUIT (3 in this exmple), nd press Enter. The SS7 Numering Pln menu system termintes, nd the following prompt ppers. Continue to Step 8.
26 5-26 Chpter 5: Configurtion of ISDN Protocols Do you wnt to mnully mp Clled nd Clling Prty Numer Type of Numer from ISDN going to the SS7 Nture of Address Ind. (y/n, current=n) : 8 Do one of the following: If you do not wnt to mnully mp the ISDN Type of Numer for the clled nd clling prty numers, type n nd press Enter. The following prompt ppers. Go to Step 11. Do you wnt to mnully mp Clled nd Clling Prty Numer Numering Pln from ISDN going to SS7 Numering Pln (y/n, current=n) : If you wnt to mnully mp the ISDN Type of Numer for the clled nd clling prty numers, type y nd press Enter. The ISDN Type of Numer menu ppers. Note: The types of items (nd, consequently, the numer of items) on this menu depend on the type of ISDN instlled on this SP201. Incoming ISDN Outgoing SS7 Numer Type of Numer Nture of Address Unknown --> Ntionl Numer 2 Interntionl --> Interntionl Numer 3 Ntionl --> Ntionl Numer 4 Network Specific --> Ntionl Numer 5 Suscrier Numer --> Suscrier numer 6 Arevited Numer --> Ntionl Numer 7 Reserved-extension --> Ntionl Numer 8 QUIT Enter the numer of the prmeter you wish to chnge (1-8):
27 Configuring ISDN LAPD nd Cll Control Do one of the following: To exit the ISDN Type of Numer menu, type the line numer for QUIT (8 in this exmple), nd press Enter. (Or just press Enter without typing nything.) The following prompt ppers. Go to Step 11. Do you wnt to mnully mp Clled nd Clling Prty Numer Numering Pln from ISDN going to SS7 Numering Pln (y/n, current=n) : Type the line numer of the Incoming ISDN Type of Numer item you wish to chnge, nd press Enter. An item menu similr to the following ppers, where x represents the Incoming ISDN Type of Numer item whose line numer you selected. (The outgoing options depend on permissile Outgoing SS7 Nture of Address vlues for Incoming ISDN Type of Numer item x.) Trnslte incoming "x" to outgoing vlue: 1 Unknown 2 Suscrier numer 3 Ntionl Numer 4 Interntionl Numer 5 Suscr #, op rqsted 6 Ntl #, op rqsted 7 Intntl #, op rqsted 8 No #, op rqsted 9 No #, cll crrier cll 11 Test line test code 12 QUIT Enter the numer you wish to mp the prmeter to (1-12): 10 Do one of the following: To exit the item menu without chnging Incoming item x s outgoing option, do not type nything. Just press Enter. The ISDN Type of Numer menu re-ppers. Go to Step 9.
28 5-28 Chpter 5: Configurtion of ISDN Protocols Type the line numer for the outgoing vlue you wish the Incoming item x to use, nd press Enter. The outgoing vlue for incoming item x is chnged, nd the ISDN Type of Numer menu re-ppers. Go to Step 9. c To exit the ISDN Type of Numer menu system, type the line numer for QUIT (12 in this exmple), nd press Enter. The ISDN Type of Numer menu system termintes, nd the following prompt ppers. Continue to Step 11. Do you wnt to mnully mp Clled nd Clling Prty Numer Numering Pln from ISDN going to SS7 Numering Pln (y/n, current=n) : 11 Do one of the following: If you do not wnt to mnully mp the ISDN Numering Pln for the clled nd clling prty numers, type n nd press Enter. The user> prompt ppers. If you wnt to mnully mp the ISDN Numering Pln for the clled nd clling prty numers, type y nd press Enter. The ISDN Numering Pln menu ppers. Note: The types of items (nd, consequently, the numer of items) on this menu depend on the type of ISDN instlled on this SP201.
29 Configuring ISDN LAPD nd Cll Control 5-29 Incoming ISDN Outgoing SS7 Numer Numering Pln Numering Pln Unknown --> ISDN/telephony num 2 ISDN/telephony num --> ISDN/telephony num 3 Dt Numering - X > ISDN/telephony num 4 Telex numering - F.69 --> ISDN/telephony num 5 Ntionl Stndrd Num. --> ISDN/telephony num 6 Privte Numering --> privte numering 7 Reserved for Ext. --> ISDN/telephony num 8 QUIT Enter the numer of the prmeter you wish to chnge (1-8): 12 Do one of the following: To exit the ISDN Numering Pln menu, type the line numer for QUIT (8 in this exmple), nd press Enter. (Or just press Enter without typing nything.) The user> prompt ppers. Type the line numer of the Incoming ISDN Numering Pln item you wish to chnge, nd press Enter. An item menu similr to the following ppers, where x represents the Incoming ISDN Numering Pln item whose line numer you selected. (The outgoing options depend on permissile Outgoing SS7 Numering Pln vlues for Incoming ISDN Numering Pln item x.) Trnslte incoming "x" to outgoing vlue: 1 Unknown 2 ISDN/telephony num 3 privte numering 4 QUIT Enter the numer you wish to mp the prmeter to (1-4): 13 Do one of the following: To exit the item menu without chnging Incoming item x s outgoing option, do not type nything. Just press Enter.
30 5-30 Chpter 5: Configurtion of ISDN Protocols The ISDN Numering Pln menu re-ppers. Go to Step 12. Type the line numer for the outgoing vlue you wish the Incoming item x to use, nd press Enter. The outgoing vlue for incoming item x is chnged, nd the ISDN Numering Pln menu re-ppers. Go to Step 12. c To exit the ISDN Numering Pln menu system, type the line numer for QUIT (4 in this exmple), nd press Enter. The ISDN Numering Pln menu system termintes, nd the user> prompt re-ppers The config cc overlp Commnd This commnd enles or disles overlp diling in ETSI ISDN. How to Use the config cc overlp Commnd 1 At the user> prompt, type config cc overlp nd press Enter. The following prompt ppers. Enle ETSI Overlp Diling option? (y/n, current=n) : 2 Answer y or n nd press Enter. The user> prompt is re-displyed The config cc useruserinfo Commnd This commnd indictes whether the ISDN Setup messge will include user-to-user informtion element with informtion collected from the clling prty numer, the chrge numer, nd the originl clled numer in the ISUP IAM.
31 The ISDN Rte Converter 5-31 How to Use the config cc useruserinfo Commnd 1 At the user> prompt, type config cc useruserinfo nd press Enter. The following prompt ppers. Do you wnt to dd the user-user element with informtion from the clling prty numer, chrge numer nd originl clled numer (y/n, current=y) : 2 Answer y or n nd press Enter. The user> prompt re-ppers. 5.5 The ISDN Rte Converter Note: Although this softwre is clled the ISDN Rte Converter, it is generlly ville for rte conversion in other protocols. If you need to use rte conversion for protocol other thn ISDN, contct your sles representtive to determine how to proceed. In SignlPth softwre 1110 nd ove, ISDN rte conversion includes E1 E1 rte conversion, T1 T1 rte conversion, nd E1 T1 rte conversion. The softwre senses whether the SP201 hs eight E1 ports, eight T1 ports, or E1 ports for trunks 1 4 nd T1 ports for trunks 5 8, nd uses the pproprite E1 E1, T1 T1, or E1 T1 rte conversion. (The SP201 must support one of these port configurtions; otherwise, the softwre my not perform properly.) See the following sections for detils of rte conversion: Section 5.5.1, The E1 E1 Rte Converter Section 5.5.2, The T1 T1 Rte Converter Section 5.5.3, The E1 T1 Rte Converter Becuse the rte conversion softwre does not perform ny spect of signling conversion other thn tht of rte conversion (nd, when pproprite, E1 to T1), the softwre hs no unique commnds. Mke sure you hve configured the system-level prmeters, pying prticulr
32 5-32 Chpter 5: Configurtion of ISDN Protocols ttention to the config frmer commnd for trunks. See the following sections to configure the system-level prmeters for rte conversion: Section 2.3.2, The config frmer Commnd Section 2.3.5, The config clocks Commnd Section 2.3.3, The config lrms Commnd Section 2.3.4, The config lmrely Commnd The E1 E1 Rte Converter The softwre for E1 E1 rte conversion psses signls etween switch tht uses E1 trunks with A-lw nd one tht uses E1 trunks with µ-lw (mu-lw). In this setup, A-lw to µ-lw conversion is used for the erer chnnels, nd the signling chnnel is pssed through s cler chnnel from timeslot 16 to timeslot 24. All other properties of the signls re pssed through without chnge. The E1 E1 conversion softwre must, of course, e instlled on n SP201 tht hs eight E1 ports. (For descriptions of specific trunk configurtions, see the SP201 Hrdwre Reference Guide.) When the softwre senses eight E1 ports, it utomticlly ssigns A-lw for trunks 1 4 nd µ-lw for trunks 5 8. Mke sure the trunks tht will e used for conversion re connected to the respective E1 devices, nd configure the softwre prmeters The T1 T1 Rte Converter The softwre for T1 T1 rte conversion psses signls etween switch tht uses T1 trunks with A-lw nd one tht uses T1 trunks with µ-lw (mu-lw). In this setup, A-lw to µ-lw conversion is used for the erer chnnels (1 23), nd the signling chnnel (24) is pssed through s cler chnnel. All other properties of the signls re pssed through without chnge. The T1 T1 conversion softwre must, of course, e instlled on n SP201 tht hs eight T1 ports. (For descriptions of specific trunk configurtions, see the SP201 Hrdwre Reference Guide.) When the softwre senses eight T1 ports, it utomticlly ssigns A-lw for trunks 1 4 nd µ-lw for trunks 5 8. Mke sure the trunks tht will e used for conversion re connected to the respective T1 devices, nd configure the softwre prmeters The E1 T1 Rte Converter The softwre for E1 T1 rte conversion psses signls etween switch tht uses E1 trunks nd one tht uses T1 trunks. The rte converter mps the E1
33 The ISDN Rte Converter 5-33 signling chnnel (timeslot 16) to the T1 signling chnnel (timeslot 24), nd uses A-lw to µ-lw (mu-lw) conversion for the erer chnnels. (E1 trunks use A-lw; T1 trunks use µ-lw.) All other properties of the signls re pssed through without chnge. The E1 T1 conversion softwre must, of course, e instlled on n SP201 tht hs oth E1 ports nd T1 ports. The LIM must hve E1 ports for trunks 1 4 nd T1 ports for trunks 5 8. (For descriptions of specific trunk configurtions, see the SP201 Hrdwre Reference Guide.) Mke sure the trunks tht will e used for conversion re connected to the respective E1 nd T1 devices, nd configure the softwre prmeters.
34 5-34 Chpter 5: Configurtion of ISDN Protocols
Engineer-to-Engineer Note
Engineer-to-Engineer Note EE-265 Technicl notes on using Anlog Devices DSPs, processors nd development tools Contct our technicl support t dsp.support@nlog.com nd t dsptools.support@nlog.com Or visit our
More informationOverview of International Roaming (WORLD WING)
Overses Use Overview of Interntionl Roming (WORLD WING)... 306 Services Aville Overses... 306 Checking efore Using Overses... 307 Mking Clls Overses... 309 Receiving Clls Overses... 312 Setting Network
More informationAntiSpyware Enterprise Module 8.5
AntiSpywre Enterprise Module 8.5 Product Guide Aout the AntiSpywre Enterprise Module The McAfee AntiSpywre Enterprise Module 8.5 is n dd-on to the VirusScn Enterprise 8.5i product tht extends its ility
More information5 a LAN 6 a gateway 7 a modem
STARTER With the help of this digrm, try to descrie the function of these components of typicl network system: 1 file server 2 ridge 3 router 4 ckone 5 LAN 6 gtewy 7 modem Another Novell LAN Router Internet
More informationLicense Manager Installation and Setup
The Network License (concurrent-user) version of e-dpp hs hrdwre key plugged to the computer running the License Mnger softwre. In the e-dpp terminology, this computer is clled the License Mnger Server.
More informationStart Here. IMPORTANT: To ensure that the software is installed correctly, do not connect the USB cable until step 17. Remove tape and cardboard
Strt Here 1 IMPORTANT: To ensure tht the softwre is instlled correctly, do not connect the USB cle until step 17. Follow the steps in order. If you hve prolems during setup, see Trouleshooting in the lst
More informationReasoning to Solve Equations and Inequalities
Lesson4 Resoning to Solve Equtions nd Inequlities In erlier work in this unit, you modeled situtions with severl vriles nd equtions. For exmple, suppose you were given usiness plns for concert showing
More informationWelch Allyn CardioPerfect Workstation Installation Guide
Welch Allyn CrdioPerfect Worksttion Instlltion Guide INSTALLING CARDIOPERFECT WORKSTATION SOFTWARE & ACCESSORIES ON A SINGLE PC For softwre version 1.6.5 or lter For network instlltion, plese refer to
More informationNew Internet Radio Feature
XXXXX XXXXX XXXXX /XW-SMA3/XW-SMA4 New Internet Rdio Feture EN This wireless speker hs een designed to llow you to enjoy Pndor*/Internet Rdio. In order to ply Pndor/Internet Rdio, however, it my e necessry
More informationProtocol Analysis. 17-654/17-764 Analysis of Software Artifacts Kevin Bierhoff
Protocol Anlysis 17-654/17-764 Anlysis of Softwre Artifcts Kevin Bierhoff Tke-Awys Protocols define temporl ordering of events Cn often be cptured with stte mchines Protocol nlysis needs to py ttention
More informationEasyMP Network Projection Operation Guide
EsyMP Network Projection Opertion Guide Contents 2 About EsyMP Network Projection Functions of EsyMP Network Projection... 5 Vrious Screen Trnsfer Functions... 5 Instlling the Softwre... 6 Softwre Requirements...6
More informationVoIP for the Small Business
VoIP for the Smll Business Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become
More informationVoIP for the Small Business
Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become vible solution for even the
More informationHow To Reduce Telecommunictions Costs
Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become vible solution for even the
More informationSTRM Log Manager Installation Guide
Security Thret Response Mnger Relese 2012.0 Juniper Networks, Inc. 1194 North Mthild Avenue Sunnyvle, CA 94089 USA 408-745-2000 www.juniper.net Pulished: 2012-09-12 Copyright Notice Copyright 2012 Juniper
More informationVoIP for the Small Business
Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become vible solution for even the
More informationVoIP for the Small Business
VoIP for the Smll Business Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become
More informationVoIP for the Small Business
Reducing your telecommunictions costs VoIP (Voice over Internet Protocol) offers low cost lterntive to expensive trditionl phone services nd is rpidly becoming the communictions system of choice for smll
More informationVoIP for the Small Business
Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become vible solution for even the
More informationVoIP for the Small Business
VoIP for the Smll Business Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become
More informationVoIP for the Small Business
Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become vible solution for even the
More informationVoIP for the Small Business
VoIP for the Smll Business Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become
More informationTechnical manual for Multi Apartment Gateway 1456B Passion.Technology.Design.
E TECHICAL MAUAL Art 456B B + - 40-56 Vdc SOLO CO CAVO ROSSO COMELIT 2E7T000500 OLY WITH COMELIT RED CABLE 2E7T000500 FIXED POE SETTABLE POE 0 POE A A2 A3 A4 Technicl mnul for Multi Aprtment Gtewy 456B
More informationVoIP for the Small Business
VoIP for the Smll Business Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become
More informationHow To Get A Free Phone Line From A Cell Phone To A Landline For A Business
Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become vible solution for even the
More informationFAULT TREES AND RELIABILITY BLOCK DIAGRAMS. Harry G. Kwatny. Department of Mechanical Engineering & Mechanics Drexel University
SYSTEM FAULT AND Hrry G. Kwtny Deprtment of Mechnicl Engineering & Mechnics Drexel University OUTLINE SYSTEM RBD Definition RBDs nd Fult Trees System Structure Structure Functions Pths nd Cutsets Reliility
More informationClearPeaks Customer Care Guide. Business as Usual (BaU) Services Peace of mind for your BI Investment
ClerPeks Customer Cre Guide Business s Usul (BU) Services Pece of mind for your BI Investment ClerPeks Customer Cre Business s Usul Services Tble of Contents 1. Overview...3 Benefits of Choosing ClerPeks
More informationPolynomial Functions. Polynomial functions in one variable can be written in expanded form as ( )
Polynomil Functions Polynomil functions in one vrible cn be written in expnded form s n n 1 n 2 2 f x = x + x + x + + x + x+ n n 1 n 2 2 1 0 Exmples of polynomils in expnded form re nd 3 8 7 4 = 5 4 +
More informationVoIP for the Small Business
Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become vible solution for even the
More informationVoIP for the Small Business
VoIP for the Smll Business Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become
More informationSmall Business Networking
Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd business. Introducing technology
More informationSmall Business Networking
Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd business. Introducing technology
More informationVoIP for the Small Business
Reducing your telecommunictions costs TechAdvisory.org SME Reports sponsored by Cybernut Solutions provides outsourced IT support from welth of knowledgeble technicins nd system dministrtors certified
More informationVoIP for the Small Business
Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become vible solution for even the
More informationCallPilot 100/150 Upgrade Addendum
CllPilot 100/150 Relese 3.0 Softwre Upgrde Addendum Instlling new softwre onto the CllPilot 100/150 Feture Crtridge CllPilot 100/150 Upgrde Addendum Prerequisites lptop or desktop computer tht cn ccept
More informationArchitecture and Data Flows Reference Guide
Architecture nd Dt Flows Reference Guide BlckBerry Enterprise Service 12 Version 12.0 Pulished: 2014-11-10 SWD-20141110103011848 Contents Components used in the BES12 solution... 5 Components used to mnge
More informationSmall Business Networking
Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd processes. Introducing technology
More informationVoIP for the Small Business
Reducing your telecommunictions costs Reserch firm IDC 1 hs estimted tht VoIP system cn reduce telephony-relted expenses by 30%. Voice over Internet Protocol (VoIP) hs become vible solution for even the
More informationVirtual Machine. Part II: Program Control. Building a Modern Computer From First Principles. www.nand2tetris.org
Virtul Mchine Prt II: Progrm Control Building Modern Computer From First Principles www.nnd2tetris.org Elements of Computing Systems, Nisn & Schocken, MIT Press, www.nnd2tetris.org, Chpter 8: Virtul Mchine,
More informationSmall Business Networking
Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd processes. Introducing technology
More informationHow To Network A Smll Business
Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd processes. Introducing technology
More informationQuick Reference Guide: One-time Account Update
Quick Reference Guide: One-time Account Updte How to complete The Quick Reference Guide shows wht existing SingPss users need to do when logging in to the enhnced SingPss service for the first time. 1)
More informationUse Geometry Expressions to create a more complex locus of points. Find evidence for equivalence using Geometry Expressions.
Lerning Objectives Loci nd Conics Lesson 3: The Ellipse Level: Preclculus Time required: 120 minutes In this lesson, students will generlize their knowledge of the circle to the ellipse. The prmetric nd
More information2 DIODE CLIPPING and CLAMPING CIRCUITS
2 DIODE CLIPPING nd CLAMPING CIRCUITS 2.1 Ojectives Understnding the operting principle of diode clipping circuit Understnding the operting principle of clmping circuit Understnding the wveform chnge of
More informationVMware Horizon Mirage Web Manager Guide
VMwre Horizon Mirge We Mnger Guide Horizon Mirge 4.3 This document supports the version of ech product listed nd supports ll susequent versions until the document is replced y new edition. To check for
More informationHP Application Lifecycle Management
HP Appliction Lifecycle Mngement Softwre Version: 11.00 Tutoril Document Relese Dte: Novemer 2010 Softwre Relese Dte: Novemer 2010 Legl Notices Wrrnty The only wrrnties for HP products nd services re set
More informationVendor Rating for Service Desk Selection
Vendor Presented By DATE Using the scores of 0, 1, 2, or 3, plese rte the vendor's presenttion on how well they demonstrted the functionl requirements in the res below. Also consider how efficient nd functionl
More informationCS99S Laboratory 2 Preparation Copyright W. J. Dally 2001 October 1, 2001
CS99S Lortory 2 Preprtion Copyright W. J. Dlly 2 Octoer, 2 Ojectives:. Understnd the principle of sttic CMOS gte circuits 2. Build simple logic gtes from MOS trnsistors 3. Evlute these gtes to oserve logic
More informationKofax Reporting. Administrator's Guide 2.0.0 2013-09-19
Kofx Reporting 2.0.0 Administrtor's Guide 2013-09-19 2013 Kofx, Inc. All rights reserved. Use is subject to license terms. Third-prty softwre is copyrighted nd licensed from Kofx s suppliers. THIS SOFTWARE
More informationT H E S E C U R E T R A N S M I S S I O N P R O T O C O L O F S E N S O R A D H O C N E T W O R K
Z E S Z Y T Y N A U K O W E A K A D E M I I M A R Y N A R K I W O J E N N E J S C I E N T I F I C J O U R N A L O F P O L I S H N A V A L A C A D E M Y 2015 (LVI) 4 (203) A n d r z e j M r c z k DOI: 10.5604/0860889X.1187607
More informationCombined Liability Insurance. Information and Communication Technology Proposal form
Comined Liility Insurnce Informtion nd Communiction Technology Proposl form Comined Liility Insurnce Informtion nd Communiction Technology - Proposl form This proposl form must e completed nd signed y
More informationSmall Businesses Decisions to Offer Health Insurance to Employees
Smll Businesses Decisions to Offer Helth Insurnce to Employees Ctherine McLughlin nd Adm Swinurn, June 2014 Employer-sponsored helth insurnce (ESI) is the dominnt source of coverge for nonelderly dults
More informationA Network Management System for Power-Line Communications and its Verification by Simulation
A Network Mngement System for Power-Line Communictions nd its Verifiction y Simultion Mrkus Seeck, Gerd Bumiller GmH Unterschluerscher-Huptstr. 10, D-90613 Großhersdorf, Germny Phone: +49 9105 9960-51,
More informationEngineer-to-Engineer Note
Engineer-to-Engineer Note EE-234 Technicl notes on using Anlog Devices DSPs, processors nd development tools Contct our technicl support t dsp.support@nlog.com nd t dsptools.support@nlog.com Or visit our
More informationUnleashing the Power of Cloud
Unleshing the Power of Cloud A Joint White Pper by FusionLyer nd NetIQ Copyright 2015 FusionLyer, Inc. All rights reserved. No prt of this publiction my be reproduced, stored in retrievl system, or trnsmitted,
More informationIntegration by Substitution
Integrtion by Substitution Dr. Philippe B. Lvl Kennesw Stte University August, 8 Abstrct This hndout contins mteril on very importnt integrtion method clled integrtion by substitution. Substitution is
More informationExperiment 6: Friction
Experiment 6: Friction In previous lbs we studied Newton s lws in n idel setting, tht is, one where friction nd ir resistnce were ignored. However, from our everydy experience with motion, we know tht
More informationOperations with Polynomials
38 Chpter P Prerequisites P.4 Opertions with Polynomils Wht you should lern: Write polynomils in stndrd form nd identify the leding coefficients nd degrees of polynomils Add nd subtrct polynomils Multiply
More informationORGANIZER QUICK REFERENCE GUIDE
NOTES ON ORGANIZING AND SCHEDULING MEETINGS Individul GoToMeeting orgnizers my hold meetings for up to 15 ttendees. GoToMeeting Corporte orgnizers my hold meetings for up to 25 ttendees. GoToMeeting orgnizers
More informationthe machine and check the components
Quick Setup Guide Strt Here HL-2270DW Before using this mchine for the first time, red this Quick Setup Guide to setup nd instll your mchine. To view the Quick Setup Guide in other lnguges, plese visit
More informationHow To Set Up A Network For Your Business
Why Network is n Essentil Productivity Tool for Any Smll Business TechAdvisory.org SME Reports sponsored by Effective technology is essentil for smll businesses looking to increse their productivity. Computer
More informationNetwork Configuration Independence Mechanism
3GPP TSG SA WG3 Security S3#19 S3-010323 3-6 July, 2001 Newbury, UK Source: Title: Document for: AT&T Wireless Network Configurtion Independence Mechnism Approvl 1 Introduction During the lst S3 meeting
More informationWireless Wakeups Revisited: Energy Management for VoIP over Wi-Fi Smartphones
Wireless Wkeups Revisited: Energy Mngement for VoIP over Wi-Fi Smrtphones Yuvrj Agrwl, Rnveer Chndr,AlecWolmn, Prmvir Bhl, Kevin Chin, Rjesh Gupt Microsoft Reserch, Microsoft Corportion, University of
More informationStudent Access to Virtual Desktops from personally owned Windows computers
Student Aess to Virtul Desktops from personlly owned Windows omputers Mdison College is plesed to nnoune the ility for students to ess nd use virtul desktops, vi Mdison College wireless, from personlly
More informationthe machine and check the components
Quick Setup Guide Strt Here DCP-7055W / DCP-7057W DCP-7070DW Plese red the Sfety nd Legl ooklet first efore you set up your mchine. Then, plese red this Quick Setup Guide for the correct setup nd instlltion.
More informationHow To Organize A Meeting On Gotomeeting
NOTES ON ORGANIZING AND SCHEDULING MEETINGS Individul GoToMeeting orgnizers my hold meetings for up to 15 ttendees. GoToMeeting Corporte orgnizers my hold meetings for up to 25 ttendees. GoToMeeting orgnizers
More informationTwo hours UNIVERSITY OF MANCHESTER SCHOOL OF COMPUTER SCIENCE. Date: Friday 16 th May 2008. Time: 14:00 16:00
COMP20212 Two hours UNIVERSITY OF MANCHESTER SCHOOL OF COMPUTER SCIENCE Digitl Design Techniques Dte: Fridy 16 th My 2008 Time: 14:00 16:00 Plese nswer ny THREE Questions from the FOUR questions provided
More informationManual Headend Controller (HCB 100 blue (9650.03)
Mnul Hedend Controller (HCB 100 blue (9650.03) Chnges due to technicl progress possible! Hermnn - Petersilge - Strße 1 D-07422 Bd Blnkenburg Germny Phone: ++ 49 (0) 36 74 1/60-0 Telef: ++ 49 (0) 36 74
More informationActive & Retiree Plan: Trustees of the Milwaukee Roofers Health Fund Coverage Period: 06/01/2015-05/31/2016 Summary of Benefits and Coverage:
Summry of Benefits nd Coverge: Wht this Pln Covers & Wht it Costs Coverge for: Single & Fmily Pln Type: NPOS This is only summry. If you wnt more detil bout your coverge nd costs, you cn get the complete
More informationAnthem Blue Cross Life and Health Insurance Company University of Southern California Custom Premier PPO 800/20%/20%
Anthem Blue Cross Life nd Helth Insurnce Compny University of Southern Cliforni Custom Premier 800/20%/20% Summry of Benefits nd Coverge: Wht this Pln Covers & Wht it Costs Coverge Period: 01/01/2015-12/31/2015
More informationQoS Mechanisms C HAPTER 3. 3.1 Introduction. 3.2 Classification
C HAPTER 3 QoS Mechnisms 3.1 Introduction In the previous chpter, we introduced the fundmentl QoS concepts. In this chpter we introduce number of key QoS mechnisms tht enble QoS services. At the end of
More informationSmall Business Cloud Services
Smll Business Cloud Services Summry. We re thick in the midst of historic se-chnge in computing. Like the emergence of personl computers, grphicl user interfces, nd mobile devices, the cloud is lredy profoundly
More informationMcAfee Network Security Platform
XC-240 Lod Blner Appline Quik Strt Guide Revision D MAfee Network Seurity Pltform This quik strt guide explins how to quikly set up nd tivte your MAfee Network Seurity Pltform XC-240 Lod Blner. The SFP+
More informationEngineer-to-Engineer Note
Engineer-to-Engineer Note EE-280 Technicl notes on using Anlog Devices DSPs, processors nd development tools Visit our Web resources http://www.nlog.com/ee-notes nd http://www.nlog.com/processors or e-mil
More informationMorgan Stanley Ad Hoc Reporting Guide
spphire user guide Ferury 2015 Morgn Stnley Ad Hoc Reporting Guide An Overview For Spphire Users 1 Introduction The Ad Hoc Reporting tool is ville for your reporting needs outside of the Spphire stndrd
More informationProject 6 Aircraft static stability and control
Project 6 Aircrft sttic stbility nd control The min objective of the project No. 6 is to compute the chrcteristics of the ircrft sttic stbility nd control chrcteristics in the pitch nd roll chnnel. The
More informationIntellio Video System 25
Intellio Video System 3 Video mngement softwre Min fetures streming Developed for Intellio smrtcmers Multi-megpixel network video recording Amplitude sed udio recording Monitoring 2 30 cmers per worksttion
More informationTechniques for Requirements Gathering and Definition. Kristian Persson Principal Product Specialist
Techniques for Requirements Gthering nd Definition Kristin Persson Principl Product Specilist Requirements Lifecycle Mngement Elicit nd define business/user requirements Vlidte requirements Anlyze requirements
More informationGFI MilArchiver 6 vs C2C Archive One Policy Mnger GFI Softwre www.gfi.com GFI MilArchiver 6 vs C2C Archive One Policy Mnger GFI MilArchiver 6 C2C Archive One Policy Mnger Who we re Generl fetures Supports
More informationAdvanced Baseline and Release Management. Ed Taekema
Advnced Bseline nd Relese Mngement Ed Tekem Introduction to Bselines Telelogic Synergy uses bselines to perform number of criticl configurtion mngement tsks. They record the stte of the evolving softwre
More informationIaaS Configuration for Virtual Platforms
IS Configurtion for Virtul Pltforms vcloud Automtion Center 6.0 This document supports the version of ech product listed nd supports ll susequent versions until the document is replced y new edition. To
More informationIdeaPad Y470/ Y570. User Guide V1.0. Read the safety notices and important tips in the included manuals before using your computer.
IdePd Y470/ Y570 User Guide V1.0 Red the sfety notices nd importnt tips in the included mnuls efore using your computer. Notes Before using the product, e sure to red Lenovo Sfety nd Generl Informtion
More informationAccording to Webster s, the
dt modeling Universl Dt Models nd P tterns By Len Silversn According Webster s, term universl cn be defined s generlly pplicble s well s pplying whole. There re some very common ptterns tht cn be generlly
More information1.00/1.001 Introduction to Computers and Engineering Problem Solving Fall 2011 - Final Exam
1./1.1 Introduction to Computers nd Engineering Problem Solving Fll 211 - Finl Exm Nme: MIT Emil: TA: Section: You hve 3 hours to complete this exm. In ll questions, you should ssume tht ll necessry pckges
More informationJaERM Software-as-a-Solution Package
JERM Softwre-s--Solution Pckge Enterprise Risk Mngement ( ERM ) Public listed compnies nd orgnistions providing finncil services re required by Monetry Authority of Singpore ( MAS ) nd/or Singpore Stock
More informationGFI MilArchiver 6 vs Quest Softwre Archive Mnger GFI Softwre www.gfi.com GFI MilArchiver 6 vs Quest Softwre Archive Mnger GFI MilArchiver 6 Quest Softwre Archive Mnger Who we re Generl fetures Supports
More informationEngineer-to-Engineer Note
Engineer-to-Engineer Note EE-220 Technicl notes on using Anlog Devices DSPs, processors nd development tools Contct our technicl support t dsp.support@nlog.com nd t dsptools.support@nlog.com Or visit our
More informationSection 7-4 Translation of Axes
62 7 ADDITIONAL TOPICS IN ANALYTIC GEOMETRY Section 7-4 Trnsltion of Aes Trnsltion of Aes Stndrd Equtions of Trnslted Conics Grphing Equtions of the Form A 2 C 2 D E F 0 Finding Equtions of Conics In the
More informationThe Velocity Factor of an Insulated Two-Wire Transmission Line
The Velocity Fctor of n Insulted Two-Wire Trnsmission Line Problem Kirk T. McDonld Joseph Henry Lbortories, Princeton University, Princeton, NJ 08544 Mrch 7, 008 Estimte the velocity fctor F = v/c nd the
More informationMath 135 Circles and Completing the Square Examples
Mth 135 Circles nd Completing the Squre Exmples A perfect squre is number such tht = b 2 for some rel number b. Some exmples of perfect squres re 4 = 2 2, 16 = 4 2, 169 = 13 2. We wish to hve method for
More informationVectors 2. 1. Recap of vectors
Vectors 2. Recp of vectors Vectors re directed line segments - they cn be represented in component form or by direction nd mgnitude. We cn use trigonometry nd Pythgors theorem to switch between the forms
More information2. Transaction Cost Economics
3 2. Trnsction Cost Economics Trnsctions Trnsctions Cn Cn Be Be Internl Internl or or Externl Externl n n Orgniztion Orgniztion Trnsctions Trnsctions occur occur whenever whenever good good or or service
More informationSection 5-4 Trigonometric Functions
5- Trigonometric Functions Section 5- Trigonometric Functions Definition of the Trigonometric Functions Clcultor Evlution of Trigonometric Functions Definition of the Trigonometric Functions Alternte Form
More informationAPPLICATION NOTE Revision 3.0 MTD/PS-0534 August 13, 2008 KODAK IMAGE SENDORS COLOR CORRECTION FOR IMAGE SENSORS
APPLICATION NOTE Revision 3.0 MTD/PS-0534 August 13, 2008 KODAK IMAGE SENDORS COLOR CORRECTION FOR IMAGE SENSORS TABLE OF FIGURES Figure 1: Spectrl Response of CMOS Imge Sensor...3 Figure 2: Byer CFA Ptterns...4
More informationP.3 Polynomials and Factoring. P.3 an 1. Polynomial STUDY TIP. Example 1 Writing Polynomials in Standard Form. What you should learn
33337_0P03.qp 2/27/06 24 9:3 AM Chpter P Pge 24 Prerequisites P.3 Polynomils nd Fctoring Wht you should lern Polynomils An lgeric epression is collection of vriles nd rel numers. The most common type of
More informationRRC-1258 MkII(s) m crob t. Yaesu Twin, Elecraft K3-Twin etc. User Manual USER MANUAL RRC-1258 MKII. User manual Rev. A29 2013 Maj 28 1 of 233
RRC-25 MkII(s) Yesu Twin, Elecrft K3-Twin etc. User Mnul B25B_RemoteRig_MkIIs-A29 User mnul Rev. A29 203 Mj 2 of 233 Tble of contents Sttement of Conditions... 7 Generl Description... Detchble control
More informationData replication in mobile computing
Technicl Report, My 2010 Dt repliction in mobile computing Bchelor s Thesis in Electricl Engineering Rodrigo Christovm Pmplon HALMSTAD UNIVERSITY, IDE SCHOOL OF INFORMATION SCIENCE, COMPUTER AND ELECTRICAL
More informationOUTLINE SYSTEM-ON-CHIP DESIGN. GETTING STARTED WITH VHDL August 31, 2015 GAJSKI S Y-CHART (1983) TOP-DOWN DESIGN (1)
August 31, 2015 GETTING STARTED WITH VHDL 2 Top-down design VHDL history Min elements of VHDL Entities nd rhitetures Signls nd proesses Dt types Configurtions Simultor sis The testenh onept OUTLINE 3 GAJSKI
More informationBUSINESS OWNERS PACKAGE INSURANCE APPLICATION
BUSINESS OWNERS PACKAGE INSURANCE APPLICATION Progrm ville through: CAMICO Insurnce Services Tel: 800.652.1772 Prt 1: Generl Informtion 1. Firm Nme: 2. Contct Person: (Person designted nd uthorized y the
More informationEasy Interactive Tools Ver.3.0 Operation Guide
Esy Interctive Tools Ver.3.0 Opertion Guide Esy Interctive Tools Ver.3.0 Opertion Guide Esy Interctive Tools Summry 3 Fetures Esy Interctive Tools is n ppliction tht llows you to drw on projected imges.
More information