PRTECTIN PRDUCTS - MicroClamp Description The µclamp P is a high-surge transient voltage suppressor (TVS) optimized for protection of sensitive digital sensors used in proximity switches and industrial control applications. The µclampp protects the components from over-voltages caused by Electro- Static Discharge (ESD), Electrical Fast ast Transients (EFT), and Ter ertiar tiary y Lightning. The µclampp features a working voltage of 33 volts with a minimum breakdown voltage of 34 volts. They are rated to handle a continuous forward current of up to 6mA with a low forward voltage drop of less than volt (IF = ma). They are designed with high surge capability ( Amps at t p =./5us) and a low clamping voltage of <6V. The µclampp is in an -pin SLP6P package. It measures. x.6 x.5mm. The leads are spaced at a pitch of.65mm and are finished with lead-free NiPdAu. Each device will protect one line operating at 33 volts. The small size and unique features of the µclampp make it ideal for protection of DC highside proximity switches in industrial and automotive applications. The µclampp is qualified to AEC-Q Grade. Dimensions Features µclampp TVS Diode for Proximity Switch Input Protection u Transient protection for data and power lines to IEC 6-4- (ESD) ±kv (air), ±5kV (contact) IEC 6-4-4 (EFT) 4A (5/5ns) IEC 6-4-5 (Lightning) A (./5µs) u Ultra-small package u Bidirectionally protects one data line u Low clamping voltage u Working voltage: 33V u Low leakage current u Solid-state silicon-avalanche technology u Qualified to AEC-Q Grade Mechanical Characteristics u SLP6P package u Pb-Free, Halogen Free, RoHS/WEEE Compliant u Nominal Dimensions:. x.6 x.5 mm u Lead Finish: NiPdAu u Molding compound flammability rating: UL 94V- u Marking: Marking code, cathode band u Packaging: Tape and Reel Applications u Two, Three, and Four Wire DC High-Side Proximity Switches u Digital Sensor Input Protection u Industrial Controls u 4V - 33V DC Supply Protection u Automotive Applications Schematic & Pin Configuration..65.6.5 Maximum Dimensions (mm) SLP6P (Bottom View) /3/
uclampp PRTECTIN PRDUCTS Absolute Maximum Ratings Rating Symbol Value Units Peak Pulse Power (t = 8/µs) P p k Peak Pulse Power (t =./5µs) P p k p 7 p 5 Watts Watts Peak Pulse Current ( t p =./5µs) I PP A ESD per IEC 6-4- ESD per IEC 6-4- (Air) (Contact) V ESD +/- +/- 5 kv Continuous Forward Current I MAX 6 F Electrical Characteristics (T=5 o C unless otherwise specified) Electrical Characteristics (T=5 C unless otherwise specified) ma perating Temperature T J -4 to +5 C Storage Temperature T STG 55 to +5 - C Parameter Symbol Conditions Minimum Typical Maximum Units Reverse Stand-ff Voltage V WM Reverse Breakdown Voltage R 3 V BR I t = ma T=5 C T=-4 C to 5 C 34 45 3 V V Reverse Leakage Current I R V RWM = 33V T=5 C T=5 C 5 µa Forward Voltage V F I F = ma V Clamping Voltage V C I PP = A, tp =./5µ s 6 V V Junction Capacitance C R = V, j f = MHz T=5 C 5 T=-4 C to 5 C 35 pf Semtech Corporation
uclampp PRTECTIN PRDUCTS Typical Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time Power Derating Curve Peak Pulse Power - P PP (kw). % Rated Power or I PP (%) 8 6 4.. Pulse Duration - tp (µs) 5 5 75 5 5 Ambient Temperature T A ( C) Clamping Voltage vs. Peak Pulse Current ESD Clamping (8kV Contact per IEC 6-4-) Clamping Voltage -V C (V) 7 6 5 4 T A = 5 C Waveform Parameters: tr = 8µs; td = µs Voltage (V) 75 5 5 T A = 5 C Waveform ns/6ns; 8kV peak Corrected for db attenuation. Measured with 5Ω db attenuator; 5Ω Scope Input Impedance. 3 3 4 5 Peak Pulse Current - I PP (A) 4 6 8 Time (ns) Forward Voltage vs. Forward Current Junction Capacitance vs. Reverse Voltage 5 4 T A = 5 C Waveform Parameters: tr = 8µs; td = µs 3 T A = 5 C f = MHz Forward Voltage (V) 3 Capacitance - C j (pf) 5 5 5 Peak Pulse Current (A) 3 4 Bias Voltage - (V) Semtech Corporation 3
uclampp PRTECTIN PRDUCTS Typical Characteristics Typical Positive Clamping Voltage vs Surge Voltage 6 Typical Negative Clamping Voltage vs Surge Voltage Clamp at 3ns - Clamp Voltage (V) 4 T A = 5 C. Waveform ns/6ns; 8kV peak. Corrected for db attenuation. Measured with 5 hm db attenuator; 5 hm Scope Input Impedance 4 6 8 Surge Voltage (kv) Clamp Voltage (V) -4-6 Clamp at 3ns T A = 5 C. -8 Waveform ns/6ns; 8kV peak. Corrected for db attenuation. Measured with 5 hm db attenuator; 5 hm Scope Input Impedance - - -8-6 -4 - Surge Voltage (kv) Typical Junction Capacitance vs Temperature Typical Leakage Current vs Reverse Voltage Capacitance C J (pf) 3 5 5 VR = V f = Mhz Leakage Current - IR (na).5.4.3.. TA = 5 C -5 5 5 Temperature ( C). 3 4 Reverse Voltage - VR (V) Typical Leakage Current vs Temperature Typical Breakdown Voltage vs Temperature 5 VR = 33V 5 IBR = ma Leakage Current - I R (na) 5 Breakdown Voltage - V BR (V) 45 4 35-5 5 5 Temperature ( C) 3-5 5 5 Temperature ( C) Semtech Corporation 4
uclampp PRTECTIN PRDUCTS Typical Applications Characteristics Information Typical Insertion Loss CH S LG 6 db / REF db : -.533 db 8 MHz db -6 db - db -8 db -4 db 3 4 5 : - 5.79 db 9 MHz 3: - 5.6399 db.8 GHz 4: - 3.84dB.5 GHz 5: - 3.869 db.7 GHz -3 db - db -4 db -48 db MHz MHz MHz GHz 3 GHz START. 3 MHz STP 3. MHz Applications Information Device Connection for Protection of Two, Three, and Four Wire Proximity Switches Digital sensors help to bridge the gap between the physical world and the digital world in applications such as computer controlled factory automation. In such environments, transient voltages can easily disrupt or damage sensitive sensor inputs. The µclampp provides transient voltage protection for the digital sensors to ESD, lightning, and CDE events. Device Schematic & Pin Configuration The µclampp is designed to meet the high surge capability and low clamping voltage needed to protect the ASIC and control logic used in proximity switches. The µclampp provides protection for the power and I/ lines. Application Example Vdd ASIC uclampp ut Vss Semtech Corporation 5
uclampp PRTECTIN PRDUCTS utline Drawing - SLP6P A D B aaa C A TP VIEW E A C SEATING PLANE DIMENSINS INCHES MILLIMETERS DIM MIN NM MAX MIN NM MAX A.6...4.5.55 A.....3.5 b.8...45.5.55 D.35.39.43.9.. E..4.8.5.6.7 e.6 BSC.65 BSC L.8....5.3 R..4.6.5..5 N aaa.3.8 bbb.4. PIN ID bxn bbb C A B R e x L BTTM VIEW NTES:. CNTRLLING DIMENSINS ARE IN MILLIMETERS (ANGLES IN DEGREES). Land Pattern - SLP6P (C) G Z X Y DIMENSINS DIM INCHES MILLIMETERS C (.33) (.85) G X..4.3.6 Y..55 Z.55.4 NTES:. CNTRLLING DIMENSINS ARE IN MILLIMETERS (ANGLES IN DEGREES).. THIS LAND PATTERN IS FR REFERENCE PURPSES NLY. CNSULT YUR MANUFACTURING GRUP T ENSURE YUR CMPANY'S MANUFACTURING GUIDELINES ARE MET. Semtech Corporation 6
uclampp PRTECTIN PRDUCTS Marking rdering Information Notes: Part Number Qty per Reel Reel Size uclampp.tnt, 7 Inch Notes: ) Marking will also include line matrix date code Tape and Reel Specification ) MicroClamp, uclamp and µclamp are trademarks of Semtech Corporation Bo Ko Ao Device rientation in Tape A B K.69 +/-. mm.9 +/-. mm.66 +/-. mm Note: All dimensions in mm unless otherwise specified Cathode Band Location (Towards Sprocket Holes) Contact Information Semtech Corporation Protection Products Division Flynn Rd., Camarillo, CA 93 Phone: (85)498- FAX (85)498-384 Semtech Corporation 7