RClamp0821P. Ultra-Low Capacitance 1-Line ESD protection. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics

Transcription

1 - RailClamp Description The RailClamp family is a series of ultra low capacitance Transient oltage Suppressors (TS) designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected to high-speed data and transmission lines from overvoltage caused by ESD (electrostatic discharge), CDE (Cable Discharge Events), and EFT (electrical fast transients). The RClamp TM 082P has a maximum capacitance of only 0.50pF. This allows it to be used on circuits operating in excess of 3GHz without signal attenuation. They may be used to meet the ESD iunity requirements of IEC , Level 4 (±5k air, ±8k contact discharge). The RClamp082P is in a 2-pin, RoHS/WEEE compliant, SLP006P2 package measuring.0 x 0.6 x 0.5. The leads are spaced at a pitch of 0.65 and feature a lead-free finish. Each device will protect one highspeed line operating at 8 volts. It gives the designer the flexibility to protect single lines in applications where arrays are not practical. The combination of small size, low capacitance, and high ESD surge capability makes them ideal for use in applications such as cellular phones and digital video interfaces. RClamp082P Ultra-Low Capacitance -Line ESD protection Features Transient protection for data lines to IEC (ESD) ±5k (air), ±8k (contact) IEC (EFT) 40A (tp = 5/50ns) Cable Discharge Event (CDE) Ultra-small package (.0 x 0.6 x 0.5) Protects one data or I/O line Low capacitance: 0.3pF typical Low clamping voltage Low operating voltage: 8.0 Solid-state silicon-avalanche technology Mechanical Characteristics SLP006P2 package Molding compound flaability rating: UL 94-0 Marking: Marking code Packaging : Tape and Reel Lead Finish: NiPdAu RoHS/WEEE Compliant Applications Cellular Handsets & Accessories Digital isual Interface (DI) Display Port MDDI Ports USB Ports PCI Express Serial ATA Dimensions Schematic & PIN Configuration Revision 08/30/2007 Maximum Dimensions () SLP006P2 (Bottom iew)

2 Absolute Maximum Rating Rating Symbol alue Units Peak Peak Pulse Power (tp = 8/20µs) Pulse Current (tp = 8/20µs) ESD per IEC (Air) ESD per IEC (Contact) P pk 00 Watts I PP 4 A ESD +/- 5 +/- 8 k Operating Temperature T J -55 to +25 C Storage Temperature T STG 55 to C Electrical Characteristics (T=25 o C) Parameter Symbol Conditions Minimum Typical Maximum Units Reverse Stand-Off oltage RWM 8 Reverse Breakdown oltage R B I t = ma 0 Reverse Leakage Current I R RWM = 8, T=25 C µ A Clamping oltage C I PP = A, tp = 8/20µ s 20 Clamping oltage C I PP = 4A, tp = 8/20µ s 25 Junction Capacitance C R = 0, f = MHz pf j 2007 Semtech Corp. 2

3 Typical Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time Power Derating Curve Peak Pulse Power - P PP (kw) Pulse Duration - tp (µs) % of Rated Power or I PP Ambient Temperature - T A ( o C) Clamping oltage vs. Peak Pulse Current Normalized Capacitance vs. Reverse oltage 30 2 f = MHz Clamping oltage - C () Waveform Parameters: tr = 8µs td = 20µs C J ( R ) / C J ( R =0) Peak Pulse Current - I PP (A) Reverse oltage - R () ESD Clamping (8k Contact per IEC ) Insertion Loss S2 CH S2 LOG 6 db / REF 0 db 0 db -6 db : db 900 MHz 2: db.8 GHz 3:.0090 db 2.5 GHz 4: db 2.7 GHz -2 db -8 db -24 db -30 db -36 db MHz 0 MHz 00 MHz GHz 3 GHz START. 030 MHz STOP MHz 2007 Semtech Corp. 3

4 Applications Information Device Connection Options These low capacitance TS diodes are designed to provide coon mode protection for one high-speed line or differential protection for one line pair. The device is bidirectional and may be used on lines where the signal polarity is positive and negative. Equivalent Circuit Diagram Circuit Board Layout Recoendations for Suppression of ESD. Good circuit board layout is critical for the suppression of ESD induced transients. The following guidelines are recoended: Place the TS near the input terminals or connectors to restrict transient coupling. Minimize the path length between the TS and the protected line. Minimize all conductive loops including power and ground loops. The ESD transient return path to ground should be kept as short as possible. Never run critical signals near board edges. Use ground planes whenever possible Semtech Corp. 4

5 Applications Information - Spice Model I/O Line RClamp082P Spice Model Table - RClamp082P Spice Parameters Parameter IS B J RS IB CJO TT U nit D (LCRD) D 2 (LCRD) D3 (TS) Amp.0E-20.0E E-2 olt olt Ohm Farad 0.4E-2 0.4E-2 56E-2 Amp E-3 E-3 E-3 sec 2.54E E E-9 M N EG e Semtech Corp. 5

6 Outline Drawing - SLP006P2 A D B aaa C A TOP IEW E A C SEATING PLANE DIMENSIONS INCHES MILLIMETERS DIM MIN NOM MAX MIN NOM MAX A A b D E e.026 BSC 0.65 BSC L R N 2 2 aaa bbb PIN ID bxn bbb C A B R e 2x L BOTTOM IEW NOTES:. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). Land Pattern - SLP006P2 (C) G Z X Y DIMENSIONS DIM INCHES MILLIMETERS C (.033) (0.85) G X Y Z NOTES:. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET Semtech Corp. 6

7 Marking Code Ordering Information Part Number Qty per Reel Reel Size NN RClamp082P.TCT 3,000 7 Inch Note: Lead finish is lead-free NiPdAu. RailClamp and RClamp are marks of Semtech Corporation. PIN ID Tape and Reel Specification A0 B0 K / / /-0.0 Tape Width B, (Max) D D E F K (Max) P P0 P2 T (Max) W (.65) ( ) 0.8 ±0.25 (.03).750±0. (.069±.004) 3.5±0.05 (.38±.002) 2.4 (.094) 4.0±0.0 (.57±.004) 4.0±0. (.57±.004) 2.0±0.05 (.079±.002) 0.4 (.06) (.32±.02) Contact Information Semtech Corporation Protection Products Division 200 Flynn Rd., Camarillo, CA 9302 Phone: (805)498-2 FAX (805) Semtech Corp. 7