Door Management System DORMA TMS

Door Management System DORMA TMS

DORMA TMS Door Management System DORMA TMS Your interface to systematic security With its TMS door management system, DORMA is able to offer a new departure in the development of system component control. The objective: reliable, problem-free door functions adapted to each individual requirement from the simple single-door application to the networked system incorporating a multiplicity of door devices connected to the building management system. The flexibility of the DORMA TMS door management system means that it can be used to activate SVP emergency escape locks with automatic locking action, and electrical swing door operators. It can also be readily combined with other facilities such as access control systems, intruder alarms, short-circuit TV/ video systems, etc. The DORMA TMS thus opens up the way to the creation and implementation of individualised solutions to suit your particular application. The benefits at a glance Time and cost savings at the installation phase thanks to advanced bus technology and the simplest of cabling configurations Outstanding functionality with automatic detection and pre-parameterisation of the individual components Easy programming and re-programming Integrated timer Integrated access control Disable input for intruder alarms via I/O module LON and RS interfaces, facilitating bus integration with other installations such as building control systems Comprehensive documentation for fast and reliable fault analysis if this should be required All doors can be networked and thus centrally controlled System can be visualised and parameterised Flexible connectivity of external components Approval certification DORMA emergency exit systems meet the provisions of the German DIt code of practice entitled Requirements for electrical locking systems on doors in emergency escape routes (EltVTR), and also the draft standard pren 67.

Contents Page DORMA TMS System overview 4 DORMA TL-G TMS Door terminal 7 DORMA TL-S Control and interface boards 0 DORMA TL-UP S55 Door terminal for installation in standard switch boxes DORMA RZ TMS Emergency exit control 4 DORMA TV xx DCW` Electro-mechanical locking device 6 DORMA TV xx DCW` Electro-magnetic locking device 0 DORMA TV 5xx DCW` Electro-mechanical door locking device 4 DORMA DCW` I/O module us interface module 6 DORMA TMS Accessories 8 DORMA TMS Connection diagrams 0 DORMA TMS Safety instructions 5 DCW` = DORMA CONNECT AND WORK b Additional information relating to a wide range of products can be retrieved from electronic media (Internet, CD-ROM). The codes next to the computer symbol b indicate the search terms.

DORMA TMS System Overview Door management system as electrical locking system in emergency exit doors as per EltVTR and pren 67. The door functions are controlled by the TL-S TMS control and interface PC designed for installation in door terminal enclosure TL-G xx/5xx TMS, or by emergency exit control RZ TMS. oth controls are designed for connection of max. 4 electromechanical door locking devices type TV xx DCW, key switches type ST x DCW, interface PC TL-S DCW and other DCW bus components. Connection to a hazard alarm control panel and/or fire alarm control panel or a smoke detector for emergency unlocking via a floating contact is possible. DCW system bus with component auto-identification and default parameterisation of all DCW system devices. Customised requirements can be programmed into the system via the parameterising keyboard AT 0 DCW or parameterising software TMS-Soft. System visualisation and control via PC is also possible with the TMS-Soft package. Several TMS can be networked via LON modules and LON gateways. Here, too, parameterisation, visualisation and control are performed via PC and TMS-Soft in the LON network. Integrated programmable short-time, long-time and permanent unlocking via key-operated momentary-contact control with parameterisable key actuating times and functions. In the event of a power failure, the system is immediately locked. Following authorised unlocking, re-locking is performed automatically under short-timer control between and 80 seconds, or under long-timer control between and 0 minutes, parameterised via keyboard AT-0 DCW or parameterisation software TMS-Soft. Monitoring of the door-open time begins on expiry of the timers. The door open alarm can be triggered after an adjustable time lag of 5 to 80 seconds. The duration of the pre-alarm and main alarm is also programmable. Where automatic re-locking has been activated, once the door has closed, premature re-locking via the door contact can be initiated by programming the system accordingly. Differentiated audible alarms to signal door open time exceeded (pre-alarm and/or main alarm), tamper attempt, system abuse, emergency open and fire alarm with local annunciation and automatic local alarm shutdown after 80 seconds. Integrated differential bus cables (monitored for short circuit/cable break). The functions of the integrated key switch and also those of the external key switches type ST x DCW are adjustable and restrictable. Combination possible with SVP locks, automatic door operators, etc. System TMS Standard TMS Universal TL TMS Universal RZ Special system Component TMS Standard + Psychiatric Institutions Terminal enclosure TL-G xx TMS TL-G xx TL-UP TL-G 5xx TMS TL-G 5xx S55 DCW` Interface PC TL-S TMS TL-S DCW` integrated TE 0 TL-UP S55 DCW` Control unit integrated RZ TMS Power supply Electro-mechanical door locking device integrated TV xx DCW` TV xx DCW` TV 5xx with DCW` coupler Key switch ST DCW` TL-ST PZ ST DCW` TL-ST PZ Emergency escape lock SVP 5000 Emergency escape lock with monitoring contact SVP 4000 Emergency escape lock with monitoring microswitches SVP 6000 ST 4 DCW` S55 DCW` ST 4 DCW` S55 DCW` Emergency escape motor lock SVP 000 Motor lock control SVP-Sx DCW` Accessories for SVP lock SVP-S armoured fitting Cable, cable loop SVP-A 000 KÜ/KS Other options AT 0 DCW` AS/L, TG/TE DCW` I/O module LON module LON gateway TMS-Soft 4

Data and features System TMS asic TMS Universal Function Opening of door in emergency via emergency pushbutton Short-time unlocking, adjustable ( 0 sec) Long-time unlocking 60 min. Long-time unlocking with audible acknowledge signal Permanent unlocking with audible acknowledge signal Door open monitoring ( 80 sec) Pre-alarm Main alarm Premature re-locking after door closure Lever handle pre-alarm Differentiated visual and audible status signals i-directional escape door terminal inside/door terminal outside Operation with panel module (TE 0) without local door terminal Automatic re-activation after power failure Automatic locking of the emergency escape lock Automatic re-activation by emergency escape lock Mechanical sequential control of the emergency escape lock Electrical sequential control of the emergency escape lock Emergency unlocking by fire alarm system, building control system, smoke detector, sprinkler system, etc. Passage from inside to outside via door terminal Passage from outside to inside via key switch Passage from inside to outside or outside to inside via lock Anti-tamper monitoring, TL door terminal Anti-tamper monitoring, TV electrical door locking element Integrated differential anti-tamper circuit/bus monitoring function Alarm duration limit Pre-alarm/Silent alarm Connection to 0V AC Access control Actuation control logic for automatic door operators Signal to intruder alarm/intruder alarm disable input Connection of external alarm devices Remote monitoring, remote control Remote unlocking of the emergency escape lock = Standard = Selectable/programmable = Option = Not available 5

DORMA TS TMS9 System Gleitschienen- Examples Türschließersystem RM RM MA 4 L / AS 4 6 DCW junction box 5 I/O DCW TE xx 6 TS TV DCW Concealed junction box TS TV DCW Concealed junction box SVP 5000 TL TMS SVP 4000 TL TMS LON KÜ SVP 6000 LON 0 V AC +/-0 % SVP-A 000 0 V AC +/-0 % ST DCW external TMS Standard TMS Standard + RM = smoke detector MA = fire alarm control panel LON gateway RM MA 4 LON RM MA DCW junction box ACU 0 SVP DCW I/O DCW 6 6 TMS RZ I/O DCW 0 V AC +/-0 % ED Concealed junction box TV TS TV DCW DCW Concealed junction box KÜ SVP 000 TL TMS LON KÜ SVP 4000 ST x DCW SVP-A 0 V AC +/-0 % SVP-A TE 0 TMS Universal TMS for special systems Recommended cabling: Mains feeder: NYM-I x,5 TL TMS TV xx DCW 4xx0,8 TL TMS ST x DCW xx0,8 TL TMS TE xx 4 x x 0,8 4 TL TMS RM * x x 0,8 5 TL TMS L * x x 0,8 6 LON module LON gateway x x 0,8 *via DCW I/O module 6

Systematic down to the last detail With improved ergonomics and an abundance of innovative detail solutions, the DORMA TL-G TMS door terminal offers more safety in an emergency plus optimum protection against access abuse. The control and interface PC allows control of all the door functions via a simple yet highly efficient bus technology. Technical data Power supply unit Power supply data: 0V AC, +/ 0 % Output voltage: 4V DC Output current, max.: A Temperature range: 0 to + 50 C Technical data The door terminal can also be supplied without a power pack for operation in conjunction with the RZ TMS emergency exit control unit (see TL brochure) Enclosure anti-tamper contact for activation of an internal siren and monitoring module Cover of aluminium alloy, powder-coated Assembly cylinder Signal generator board with alarm siren aseplate Key-operated momentary contact command device for alarm cancellation, locking and unlocking Europrofile single cylinder to DIN 85, or round single cylinder (both by others) Monitoring module with status display: red for locked and green for unlocked and alarm indication Illuminated red LED emergency pushbutton, positive release action, compliant with EN 60947-5- Socket connector for plug-in connection of the door terminal control PC Fluorescent foil for background illumination in the event of light failure Power supply unit Hinge for easy assembly TL-S TMS TL-S DCW Fold-down protective cover of transparent plastic with replaceable lens Control and interface PC for installation in the TL-G TMS unit 7

DORMA TL-G TMS Door Terminal The door terminal is designed for surface mounting or, when combined with the TL-UK flush-mounting recess box and TL-R frame surround, can also be installed as a concealed unit. Note TL-UK TL-G TMS TL-R According to the code of practice entitled Requirements for electrical locking systems on doors in emergency exits and escape routes (EltVTR) issued by the German Institute for uilding Technology (DIt), erlin, the emergency pushbutton for release/emergency opening of the door must be not be installed at a height of more than 00 mm above finished floor level. A height of 850 mm is recommended. Flush mounting Ø 5,5 40 TL 60 58 95 40 850 00 mm* 90 85 55 6 8 4 8

Specification text Order No. b DORMA TL-G xx/5xx TMS Anti-tamper protected door terminal enclosure of powdercoated light aluminium alloy, class of protection IP 40, for installation of the TL-S TMS control and interface PC, with integrated power supply unit and LED illuminated red emergency pushbutton, compliant with EN 60947-5-, positive opening action and integrated alarm siren with adjustable volume control >00 d. High-intensity illuminated emergency pushbutton surround with visual display of the lock status (unlocked = green, locked = red), plus visual alarm by yellow flashing light in response to tamper attempt and emergency pushbutton operation. Terminal upper section and lower section easy to install thanks to assembly cylinder accessible from the front, and hinged upper section. Lockable, hinged emergency pushbutton cover with anti-tamper contact and safety glass lens. reakable safety glass with protective film as option. Integrated key-operated momentary contact device. Power supply unit Power supply: 0V AC, +/ 0 % Output voltage: 4V DC Current input, max.: A Temperature range: 0 to +50 C Dimensions (W x H x D) approx.: 90 x 60 x 84 mm Y Prepared for Europrofile single cylinder by others to DIN 85, (locking cam centre 0.5 mm, overall length 40.5 4.5 mm) Locking cam position bottom right (max. 45 ) Y TL-G 0 TMS green (sim. to RAL 600) 5600 Y TL-G TMS white (sim. to RAL 906) 560 Y TL-G 04 TMS stainless steel Design finish 56004 Y TL-G 99 TMS special colour 56099 b TL-G TMS Y Prepared for mm dia. round single cylinder by others (locking cam centre 0.5 mm, overall length 40.5 4.5 mm) Locking cam position bottom right (max. 45 ) Y TL-G 50 TMS green (sim. to RAL 600) 56050 Y TL-G 5 TMS white (sim. to RAL 906) 5605 Y TL-G 504 TMS stainless steel Design finish 560504 Y TL-G 599 TMS special colour 560599 b TL-G TMS DORMA TL-UK Zinc-plated flush-mounting recess box for installation of the door terminal, with attachment collars as wall anchors. Adjustable baseplate for compensation of vertical mounting tolerances. Prepared for cable entry at the front and rear. Dimensions (W x H x D) approx.: x x 77 mm 56505 b TL-UK DORMA TL-R Surrounding trim, height-adjustable for adaptation to the installation depth. Dimensions (W x H x D) approx.: 0 x x 4 mm Y TL-R 08 yellowish green, fluorescent 5650408 Y TL-R white, powder-coated (sim. to RAL 906) 56504 Y TL-R 04 stainless steel Design finish 5650404 b TL-R DORMA TL-Z 0 Europrofile single cylinder with keys, with adjustable locking cam, fits in TL-G terminals, TE panel modules, ST key switches, sheet steel enclosure RZ N, NT 4 N, SVP-S 5. (Not available for keyed alike or master key systems) 565000 b TL-Z 0 DORMA TL-Z 04 Replacement lens for emergency pushbutton cover TL-G xx/5xx reakable safety glass with protective film Pack of 5 5650400 b TL-Z 04 0 0,5 9

DORMA TL-S Control and Interface PC Technical data, TL-S TMS Technical data, TL-S DCW` Power supply: Current input, max.: Contact rating: Fuse F: 4V DC, +/ 0 %, stabilised approx. 65 ma approx. 90 ma in alarm mode 4V DC, 0.5 A inductive 4 V DC,.0 A ohmic A Power supply: Current input, max.: 4V DC, +/ 0 %, stabilised approx. 75 ma approx. 90 ma in alarm mode Terminal assignment and functions, TL-S TMS Terminal assignment and functions, TL-S DCW` X X0 S X X9 X8 X X F A X6 A X9 X X 0 ON S X A X6 X Socket connector for connection of expansion module ZM 08 X Connection to the internal DCW` devices X Connection to the internal key switch/momentary contact device Power supply 4V DC, +/ 0% Connection to emergency pushbutton X6 Connection to the TV / DCW` External emergency pushbutton/smoke detector X8 PC interface RS / LON adapter X9 Connection to the firmware programming system X0 Permanent emergency pushbutton light; jumper must always be set X Connection to the TL-OM lighting module Connection to external DCW` devices X Connection to the internal DCW` devices X Connection to the internal key switch/momentary contact device Connection to emergency pushbutton X6 Connection to the TL-S TMS/RZ TMS X9 Connection to the firmware programming system X Connection to the TL-OM lighting module S Micro-switches for setting the device address: Switch Address 0 0 0 0 4 TV 4V X6 A + GND +4V DC GND +4V DC DCW bus Switched voltage for TV electrical door locking element +/ 0%, Stabilised power supply X6 A GND +4V DC DCW bus Emergency pushbutton NC contact ( Emergency stop circuit) Emergency P ext. DCW ext. A GND +4V DC GND +4V DC DCW bus Emergency pushbutton/ DORMA RM smoke detector or jumper 0

Specification text Order No. b DORMA TL-S TMS Control and interface PC for installation in TL-G xx/5xx TMS or TL-G xx/5xx. Designed for connection of max. four TV xx DCW electrical door locking elements and ST x DCW key switches, DCW I/O modules, SVP-S x DCW plus further DCW bus devices. Suitable for connection to a hazard alert system and/or fire alarm system or smoke detector (RM) for emergency unlocking via floating contact. DCW system bus with automatic device detection and default parameterisation of all DCW system components; customerspecific requirements programmable via parameterisation keypad AT 0 DCW or TMS-Soft parameterisation software. Integrated short-time, long-time and permanent unlocking via key-operated momentary contact device with programmable with parameterisable key operating times and functions. Following power failure, immediate locking action. Integrated timer with two time zones per day, adjustable via TMS-Soft. Integrated access control with AT 0 DCW pin code keypad. Automatic re-locking following authorised unlocking, effected after between and 80 seconds via short-time timer, or 0 minutes via long-time timer, programmable with parameterisation keypad AT 0 DCW or TMS-Soft parameterisation software. Door-open monitoring begins on expiry of the time set in the timers. Door-open alarm signal can be delayed from 5 to 80 seconds. Programmable duration of pre-alarm and main alarm. Programmable premature re-locking via door contact after door closure with automatic re-locking mode activated. Differentiated audible alarm for door-open time exceeded (pre- and/or main alarm), sabotage/tamper attempt, emergency-open and fire alarm signals, with local alarm indication and automatic local alarm cancellation after 80 seconds. Integrated differential bus cables (monitored for short circuit/interruption). Functionality of the integrated key switch and also the external key switch ST x DCW adjustable and definable. Prepared for connection via LON and RS interface to US or conventional systems such as integrated building management controls and additional control and signalling devices. Disabling inputs and logic function gating plus control and actuation of various systems (e.g.: automatic operators, access control system, etc.) via up to four DCW I/O modules. Power supply: 4V DC, +/ 0 % Current input, max.: approx. 65 ma approx. 90 ma in alarm mode Contact rating: 4V DC, 0.5 A inductive 4 V DC,.0 A ohmic 56000 b TL-S TMS DORMA TL-S DCW` Terminal interface board for installation in TL-G xx/5xx and connection to control types TL TMS or RZ TMS via DORMA system bus DCW. Up to 4 TL-S DCW boards can be connected via the system bus. Parameters such as adjustable and restrictable functions of the integrated key switch, the TL-S TMS or RZ TMS are automatically transferred. Power supply: 4V DC, +/ 0 % via DCW system bus Current input, max.: approx. 65 ma approx. 85 ma in alarm mode 56000 b TL-S DCW`

DORMA TL-UP S55 DCW` Door Terminal for installation in standard switch boxes System 55 design terminal The design terminal for installation in the equivalent of two standard switch boxes can be effectively matched to and combined with the most common switch and control devices incorporated in the System 55 ranges offered by manufacturers such as GIRA, erker, Merten and Jung. The terminal also comes with adapters for incorporation in other systems. The emergency pushbutton unit carries on glowing at a high intensity after operation and features an annunciator module to indicate the system condition. Technical data TL-NC S55 DCW` Power supply: Current input, max.: 4V DC, +/ 0 %, stabilised approx. 75 ma approx. 90 ma in alarm mode Terminal assignment and functions S X S ON 0 X9 S S 4 X A 6 X6 TL-STPZ S55DCW TL-NC S55DCW X X X6 X9 S S S Connection to external alarm siren Connection to the key switch Connection to the SL-S TMS (in TL TMS or RZ TMS) Connection to the firmware programming system Enclosure anti-sabotage/anti-tamper contact = Normal operation (anti-tamper contact activated) S = Service mode (anti-tamper contact de-activated) Micro-switches for setting the device address Switch Address 0 0 0 0 4 X 6 + External alarm siren (4V DC; max. 40 ma) 0 X6 A GND +4V DC DCW bus Emergency pushbutton NC contact ( Emergency stop circuit)

Specification text Order No. b DORMA TL-UP S55 DCW` Door terminal for installation in standard switch boxes (6 mm deep) to DIN 4907 Part, comprising: Emergency pushbutton/controller unit TL-NC S55 DCW and key-operated pushbutton TL-ST PZ S55 DCW for connection to emergency exit control unit RZ TMS or TL TMS, with LED-illuminated, red emergency pushbutton corresponding to EN 60947-5-, with positive opening action, brightly lit emergency pushbutton surround with optical indicator of the lock state (unlocked = green, locked = red); visual alarm provided by yellow flashing light to signal tamper/sabotage attempts and emergency pushbutton operation; audible alarm via integral alarm siren. Anti-tamper emergency pushbutton cover with glass lens of splinter-proof safety glass. All cover trims from the System 55 switch range and stainless steel unit with adapter frames can be used. TL-NC Y TL-NC S55 DCW` 560600 b S55 Scheibe eindrücken push for emergency 05574-0--40 DORMA GmbH + Co. KG Y TL-ST PZ S55 DCW` Prepared for Europrofile single cylinder by others to DIN 85, (locking cam centre 0.5 mm, overall length 40.5 4.5 mm) Locking cam position left (90 ) Y white 56070 Y silver 56070 TL-ST PZ Y anthracite 56075 b S55 Y TL-UP PZ S55 DCW` Set E Set comprising TL-NC S55 DCW, TL-ST PZ S55 DCW TL-S55 white and twin unit trim E 5600 b E System 55 trims FR-S55 Single-unit trim Standard 55 white 5690 FR-EW Single-unit trim E 55 white 5690 FR-ES Single-unit trim E 55 silver 569 FR-EA Single-unit trim E 55 anthracite 5695 FR-Esprit A Single-unit trim Esprit 55 alu 5690 FR-Esprit Single-unit trim Esprit 55 brass 56905 FR-Esprit C Single-unit trim Esprit 55 chromium 5695 FR-Esprit G Single-unit trim Esprit 55 glass 56900 FR-Esprit S Single-unit trim Esprit 55 special 56999 FR-S55 Double-unit trim Standard 55 white 5690 FR-EW Double-unit trim E 55 white 5690 FR-ES Double-unit trim E 55 silver 5690 FR-EA Double-unit trim E 55 anthracite 5695 FR-Esprit A Double-unit trim Esprit 55 alu 5690 FR-Esprit Double-unit trim Esprit 55 brass 56905 FR-Esprit C Double-unit trim Esprit 55 chromium 5695 FR-Esprit G Double-unit trim Esprit 55 glass 56900 FR-Esprit S Double-unit trim Esprit 55 special 56999 FR-S55 Triple-unit trim Standard 55 white 5690 FR-EW Triple-unit trim E 55 white 5690 FR-ES Triple-unit trim E 55 silver 5690 FR-EA Triple-unit trim E 55 anthracite 5695 FR-Esprit A Triple-unit trim Esprit 55 alu 5690 FR-Esprit Triple-unit trim Esprit 55 brass 56905 FR-Esprit C Triple-unit trim Esprit 55 chromium 5695 FR-Esprit G Triple-unit trim Esprit 55 glass 56900 FR-Esprit S Triple-unit trim Esprit 55 special 56999 b FR Other trims (e.g. IP 44, stainless steel) on application

DORMA RZ TMS Emergency Exit Control Emergency exit control With the RZ TMS emergency exit control unit, DORMA has enhanced its ability to respond to different structural situations. Consequently, you can choose between a control unit and power pack in the door terminal, or the same unit installed in a separate emergency exit control unit. All the important system components are already integrated and can be augmented for significant expandability. RZ TMS technical data Power supply: 0V AC, +/ 5% Rated input current: 0.5 A Output voltage: 4V DC, +/ 0% Rated output current max.:.5 A Temperature range: 0 to + 50 C Optional Standard TV 50x DCW` (see also page 4) DCW` branching module (see also page 8) LON module (see also page 9) TL-S TMS (see also page 0) SVP-S DCW` NT-S 4-.5 NT-S 4-.5 DCW` I/O module (see also page 6) Terminal assignment and functions, NT-S 4-.5 X N L 0V AC +/ 5 % power supply X X X +4 V DC +4 V DC X N L GND X GND GND 4

Specification text Order No. b DORMA RZ TMS Emergency exit control PC in plastics enclosure, IP 54, with cover contacts including power supply PC type DORMA NT-S 4-.5, I/O module and DCW branching module. Prepared for installation of motor lock control type DORMA SVP-S or SVP-S DCW and further I/O modules. Designed for the connection of up to 4 TL-G xx/5xx DCW or TL-UP S55, door locking elements TV xx DCW, xx DCW or 5xx DCW, and key switches type ST x DCW as well as further DCW bus devices. Suitable for connection of a hazard warning alarm and/or fire alarm and control unit or RM smoke detector for emergency unlocking via floating contact or I/O module. DCW system bus with device auto-identification; default parameterisation of all DCW system components and customer-specific requirements programmable via parameterising keyboard AT 0 DCW or parameterising software TMS-Soft. Integrated programmable short-time or long-time and permanent unlocking via key-operated momentary contact device (e.g. TL-G xx/5xx DCW, TL-UP S55 or ST key switch) with parameterisable key actuation times and functions. Instant re-locking on power failure. Automatic re-locking function after authorised unlocking programmable for 80 seconds via short timer or 0 minutes via long timer with parameterisation keyboard AT 0 DCW or parameterisation software TMS-Soft. After timer expiry, door-open monitoring mode begins. Door open alarm delay adjustable 5 80 seconds. Duration of pre-alarm and main alarm programmable. After door closure with automatic re-locking mode active, premature re-locking can be programmed for activation by door contact. Differentiated audible alarm to indicate excedence of door open time (pre-alarm and/or main alarm), tamper attempt, abuse attempt, emergency open and fire alarm with local alarm; with automatic local alarm shutdown after 80 seconds at door terminal. Integrated differential bus cables (monitored for short circuit/cable break). Functions of the external keyoperated momentary contact device, e.g. TL-G xx/5xx DCW, TL-UP S55 or ST DCW can be adjusted and restricted as required. DORMA DCW I/O module for connection of products with conventional cabling to the DORMA DCW system bus, e.g.: connection of a TG/TE monitoring and control unit, L flashing lamp, AS external alarm siren, or access control system by others. Four opto-coupler inputs for transmission of external signals and control commands, e.g. disabling input for intruder alarm system (floating or non-floating) and four floating outputs for activation of external components or for output of signals. Up to four DCW I/O modules per TMS possible. Addresses pre-parameterised for various requirements. Individual requirements can be accommodated by programming using the parameterisation keyboard AT 0 DCW or parameterisation software TMS-Soft (e.g. switch-on delay, monoflop function, flashing mode, logic/gating operations, etc.). NT-S 4-.5 Power supply: 0V AC, +/ 0 % Dimensions (W x H x D) approx.: 00 x 0 x 85 mm 5600 b RZ TMS 5

DORMA TV xx DCW` Electrical Door Locking Element Door locking element for top-jamb/frame mounting. Connection to the DORMA TMS door management system via DCW system bus. The DORMA TV xx DCW door locking element opens immediately and is immune to side load jamming. The max. holding force corresponds to the German DIt code of practice entitled Requirements for electrical locking systems on doors in emergency escape routes (EltVTR), and also the draft standard pren 67. F Approval certification In Germany, installation on DIN fire and smoke rated doors is only permitted provided that the suitability verification certificates relating to these doors include such applications, and provided that the requirements contained in said approval certificates are adhered to. Ensure compliance with relevant national and local regulations. Note A weather guard must be fitted to protect external installations. TV xx TV-Z 80 84,5 90 55 90 58 67 40 40 0 6,6 80, x 6 65 7 50 75 40 46 8 50 80, x 9 0.5 4 90 45 TV DCW 55 0 TV xx DCW TL TMS 80 50 00 Installation in the frame reveal, outward opening 6

40 0 TV-Z 0 4 TV-Z TV DCW 0 0 TV xx DCW TL TMS 50 58,5 00 Installation on flush-closing door with TV-Z shim set on the frame, outward opening 00 58,5 50 TV xx DCW TV DCW TV-Z 4 0 0 0 TV-Z KÜ TL TMS 0 40 Installation on flush-closing door with TV-Z shim set on the door exterior, without limitation of the clear passage height, outward opening 50 58,5 00 TV xx DCW TV DCW TV-Z TV-Z 0 0 4 0 KÜ TL TMS 0 40 Installation on flush-closing door with TV-Z shim set on the door without limitation of the clear passage height, inward opening 7

DORMA TV xx DCW` Electrical Door Locking Elements Technical data Power supply: Current input: 4V DC, +/ 0 %, stabilised approx. 80 ma Terminal assignment and functions X X ON S 0 A X S X X X S S Connection to TL-S TMS Connection to the internal door contact Connection to the lock solenoid Connection to the internal door contact Connection to the firmware programming system Switched voltage ( Emergency stop circuit) Enclosure anti-sabotage/anti-tamper contact Micro-switches for setting the device address Switch Address 0 0 0 0 4 X A GND +4V DC DCW` bus Switched voltage ( Emergency stop circuit) 8

Specification text Order No. b DORMA TV xx DCW` Electrical door locking element (failsafe principle) with anti-sabotage/anti-tamper and door monitoring contact, plus integrated positive-action monitoring system for active/inactive status. Installed in anti-corrosion and anti-tamper metal enclosure, spray painted. Standard package including bracket, shim set and pack of fixings. Max. holding force per EltVTR (see above) with load-independent jam-free unlocking and release. Connection to the DORMA TMS door management system via DCW system bus. Power supply: 4V DC, +/ 0% Current input max.: approx. 0 ma Recommended cabling: I-Y(ST) Y4 x x 0.6 (telecommunications lead) Dimensions (W x H x D): approx. 90 x 55 x 80 mm Y TV 0 DCW` silver 5600 Y TV 0 DCW` dark brown 5600 Y TV 04 DCW` stainless steel Design finish 56004 Y TV DCW` white (sim. to RAL 906) 560 TV xx Y TV 99 DCW` special colour 56099 b DCW` DORMA TV-Z 0 Shim set for adjusting the bracket of the DORMA TV xx DCW electrical door locking element to compensate for large installation tolerances. shims mm thick, shim mm thick. 56500 b TV-Z0 DORMA TV-Z 0xx Fixing unit for installation of the DORMA TV xx DCW electrical door locking element to flush-closing doors. Zinc-plated steel angle bracket with spray-painted cover, with anti-removal protection. Dimensions (W x H x D): approx. 90 x 58 x 84.5 mm Y TV-Z 0 silver 56500 Y TV-Z 0 dark brown 56500 Y TV-Z 04 stainless steel Design finish 565004 Y TV-Z white (sim. to RAL 906) 5650 Y TV-Z 99 special colour 565099 b TV-Zxx DORMA TV-Z 05 Fixing adapter for installation of electrical door locking element DORMA TV xx/tv xx to narrow-stile steel and timber frames. Galvanised steel plate. Dimensions (W x H x D): approx. 90 x 5 x 80 mm Y TV-Z 05 on application 9

DORMA TV xx DCW` Electrical Door Locking Element Electro-magnetic door locking element for top jamb/frame mounting. Connection to DORMA TMS door management system via DCW system bus. The DORMA TV xx DCW door locking element is a surfacecohesion electro-magnet offering high holding forces and small dimensions. The max. holding force corresponds to German DIt code of practice entitled Requirements for electrical locking systems on doors in emergency escape routes (EltVTR), and also the draft standard pren 67. F Approval certification In Germany, installation on DIN fire and smoke rated doors is only permitted provided that the suitability verification certificates relating to these doors include such applications, and provided that the requirements contained in said approval certificates are adhered to. Ensure compliance with relevant national and local regulations. Note A weather guard must be fitted to protect external installations. TV xx TV-Z 80 84,5 90 58 90 58 65 00 50 5 5,5 40 0 47 8 7 65 7 50 75 4 90 45 00 50,5 TV DCW 58 0 8 0 TV xx DCW 80 00 TL TMS 0

40 0 TV-Z 0,5 4 TV-Z TV DCW 0 8 0 TV xxdcw TL TMS 50 00 00 Installation on flush-closing door with TV-Z shim set on the frame, outward opening 00 50 TV xx DCW TV DCW TV-Z 4 0,5 8 0 0 TV-Z KÜ TL TMS 0 40 Installation on flush-closing door with TV-Z shim set on the door exterior, without limitation of the clear passage height, outward opening 00 50 00 TV xx DCW TV DCW TV-Z TV-Z 0 0,5 8 4 0 KÜ TL TMS 0 40 Installation on flush-closing door with TV-Z shim set on the door without limitation of the clear passage height, inward opening

DORMA TV xx DCW` Electrical Door Locking Element Technical data Power supply: Current input: 4V DC, +/ 0 %, stabilised approx. 00 ma Terminal assignment and functions X S ON 0 A 98 S S S X X X X X S S S Connection to TL-S TMS Connection to the internal plunger contact / external door contact Connection to the TV xx locking element Switched voltage ( Emergency stop circuit) Connection to the firmware programming system Enclosure anti-sabotage/anti-tamper contact Micro-switches for setting the device address Switch Address 0 0 0 0 4 = Normal operation (anti-tamper contact activated) S = Service mode (anti-tamper contact de-activated) X A X 8 9 GND DCW` bus +4V DC Internal plunger contact External door contact without jumper Switched voltage ( Emergency stop circuit)

Specification text Order No. b DORMA TV xx DCW` Electro-magnetic door locking element (failsafe principle) with anti-sabotage/anti-tamper and door monitoring contact, plus integrated positive-action monitoring system for active/inactive status. Magnet mounted on universal (Cardan) joint offering threedimensional adjustability. Housed in anti-corrosion, antitamper painted metal enclosure. Standard package including strike plate (also for fire doors) and fixings. Installed in anti-corrosion and anti-tamper metal enclosure, spray painted. Standard package including bracket, shim set and pack of fixings. Max. holding force per EltVTR (see above) with load-independent jam-free unlocking and release. Connection to the DORMA TMS door management system via DCW system bus. Power supply: 4V DC, +/ 0 % Current input max.: approx. 00 ma Recommended cabling: I-Y(ST) Y4 x x 0.6 (telecommunications lead) Dimensions (W x H x D): approx. 90 x 55 x 80 mm Y TV 0 DCW` silver 5600 Y TV 0 DCW` dark brown 5600 Y TV 04 DCW` stainless steel Design finish 56004 Y TV DCW` white (sim. to RAL 906) 560 TV xx Y TV 99 DCW` special colour 56099 b DCW` DORMA TV-Z xx Fixing unit for installation of the DORMA TV xx DCW electrical door locking element to flush-closing doors. Zinc-plated steel angle bracket with spray-painted cover, with anti-removal protection. Dimensions (W x H x D): approx. 90 x 58 x 84.5 mm Y TV-Z 0 silver 56500 Y TV-Z 0 dark brown 56500 Y TV-Z 04 stainless steel Design finish 565004 Y TV-Z white (sim. to RAL 906) 5650 Y TV-Z 99 special colour 565099 b TV-Zxx DORMA TV-Z 05 Fixing accessory for installation of electrical door locking element DORMA TV xx/tv xx to narrow-stile steel and timber frames. Galvanised steel plate. Dimensions (W x H x D): approx. 90 x 5 x 80 mm Y TV-Z 05 on application

DORMA TV 50x DCW` Door Locking Element Door locking element for concealed top jamb/frame mounting. Also suitable as an electric keep for emergency exit doors. Integrated feedback contacts for monitoring the active/inactive conditions. Suitable for doors with both over-rebated and flush meeting stiles. Max. holding force as per German DIt code of practice entitled Requirements for electrical locking systems on doors in emergency escape routes (EltVTR). Connection to the DORMA TMS door management system via lock adapter TV 50x DCW. The lock adapter can also be installed in the TLG-TMS door terminal or in the RZ TMS emergency exit control unit. F Approval certification In Germany, installation on DIN fire and smoke rated doors is only permitted provided that the suitability verification certificates relating to these doors include such applications, and provided that the requirements contained in said approval certificates are adhered to. Ensure compliance with relevant national and local regulations. TV 50/50 Terminal assignment and functions, TV 50x DCW` X FK A X X 4,4 5 ø 7 5 48 4 TV 505/506 4 60 4 0 0 80 0 0 00 TV 50 0 0 4 49 64,5 TV 50 X X X S S S ON 0 S S S 8 9 S Connection to the TL-S TMS (DCW bus) Connection to the internal latch contact TV 50x Connection to the door locking element TV 50x Connection to the door contact, or jumper Connection to the firmware programming system Switched voltage ( Emergency stop circuit) Enclosure anti-tamper contact Micro-switches for setting the device address: Switch Address 0 0 0 0 4 = Normal operation (anti-tamper contact activated) S = Service mode (anti-tamper contact de-activated),4 9 4,5 8 4 00 86 7 TV 505 4 5 4 59,5 49 ø 6,5 5,5 TV 506 X A X FK FK X 4 8 9 GND +4V DC + DCW bus Feedback (latch contact TV 50x): Door closed Coil Armature contact: Coil activated Ext. door contact TK or jumper Switched voltage ( Emergency stop circuit) 4

Technical data, TV 5xx Technical data, TV 5xx DCW` Power supply: 4V DC,+ / 5% Current input: approx. 60 ma Contact rating: 4V, 500 ma inductive 4V DC,.0 A ohmic Recommended cabling: I-Y(ST) Y4 x x 0.6 (telecommunications lead) Power supply: Current input, max.: 4V DC, +/ 0%, stabilised approx. ma Specification text Order No. b DORMA TV 5xx Door locking element with integrated feedback contacts for monitoring the active/inactive state. Standard package including flanged strike plate and pack of fixings. Max. holding force per EltVTR with load-independent jam-free unlocking and release. For optional connection to emergency exit control RZ or door terminals with control and interface PC TL-S5/TL-S8. Power supply: 4V DC, +/ 5% Current input: approx. 60 ma Contact rating: 4V, 500 ma inductive 4V DC,.0 A ohmic Recommended cabling: I-Y(ST) Y4 x x 0.6 (telecommunications lead) Dimensions (W x H x D) without strike plate: approx. x 4 x 9 mm With rebated strike plate 0 x 48 x 0 x for doors with over-rebated stiles Y TV 50 ISO 6 (LH) 560050 Y TV 50 ISO 5 (RH) 560050 b TV 5xx with standard flanged strike plate 5 x 00 x for doors with flush meeting stiles TV 505 ISO 6 (LH) 5600505 TV 506 ISO 5 (RH 5600506 b TV 5xx DORMA TV-Z 500 Mortise latch lock as counterpart to the TV 50xx for installation in the door leaf 5650500 b TV-Z 500 DORMA TV 50x DCW` Door lock adapter (fail-safe principle) in plastics enclosure for connection of the TV 5xx DCW to the DCW system bus. Power supply via DCW bus. Current input, max.: ma TV 50x Dimensions (W x H x D): approx. 00 x 60 x 40 mm (enclosure) 56900 b DCW` 5

DORMA DCW` I/O module us Interface Module The DCW I/O module offers four inputs and four outputs for connection and activation control of external components. Up to four I/O modules can be operated within the TMS system. In order to simplify programming, the inputs and outputs are already preprogrammed but can be individually configured as required. Technical data Power supply: Current input: Switching capacity: 4V DC, + / 0%, stabilised approx. 50 ma 4V / A (0W / 6.5VA max.) Terminal assignment and functions, DCW I/O module X S S S S 0 X X6 X0 In 4 In In In X9 Out 4 Out Out Out NO C NC NO C NC NO C NC NO C NC X8 X X A A X S S S Connection to firmware programming system Enclosure anti-tamper contact = Normal operation (anti-tamper contact activated) S = Service mode (anti-tamper contact de-activated) Micro-switches for setting the device address: Switch Address 0 0 0 0 4 DCW ext. DCW ext. X A X A GND +4V DC Address Address Address Address 4 ON ON ON ON Panel function General function Airlock control function Automatic function In In In In 4 X6 Short-time unlocking Hazard alarm Access control, SVP lever handle control panel door Long-time unlocking Freely parameterisable Disabling input SVP locked Permanent unlocking Freely parameterisable Opposite side SVP unlocked (door ) is unlocked Locking function Freely parameterisable Freely parameterisable Radar motion detector X8 NC Out C NO X9 NC Out C NO X0 NC Out C NO X NC Out 4 C NO Pre-alarm (door open) Permanent Freely parameterisable Activation of SVP unlocking active Main alarm (door open) Freely parameterisable Freely parameterisable Door contact Emergency pushbutton Freely parameterisable TV locked operated Locked Swing door operator actuation signal once SVP unlocked Freely parameterisable Freely parameterisable Door operator radar detector for long-time and permanent unlocking mode 6

Specification text Order No. b DCW` I/O module us interface module for connection of products with conventional cabling technology to the DORMA DCW system bus. Four opto-coupler inputs for transmission of external signals and control commands (floating or non-floating) and four floating outputs for actuation control of external components and/or transmission of signals. Addresses for various requirements pre-parameterised. Individual requirements can be programmed-in with parameterisation keypad AT 0 DCW or TMS-Soft parameterisation software (ON delay, OFF delay, pulse length, etc.). Power supply data: Power supply via DCW bus Current input max. 45 ma Opto-coupler inputs: U in /I in, 5V/.8mA, V/8mA, 4V/7 ma, 0V/8mA I/O module Relay outputs: 4V DC/ A 565000 b DCW` 7

AC IJK QRS PROG DE YZ LM TU FGH NOP VWX STOP DORMA TMS Accessories Specification text Order No. b DORMA ST x DCW` Key switch of anti-tamper design with LED display (red/green), light aluminium alloy enclosure, silver finish, with front panel, suitable for surface and flush mounting, for activation control of the DORMA TMS door management system. Functionality of the ST x DCW key switch adjustable and definable via parameterisation keypad AT 0 DCW or TMS- Soft parameterisation software. Connection to DORMA TMS door management system via DCW system bus. Dimensions (W x H x D), enclosure: approx. 75 x 75 x 50 mm Front panel (flush mounted): 90 x 00 x mm. Y ST DCW` prepared for Europrofile single cylinder by others to DIN 85 (locking cam centre 0-.5 mm, overall length 40.5 4.5 mm), cam position left (90 ) 56400 b STDCW` Y ST 4 DCW` prepared for mm dia. round single cylinder by others (locking cam centre 0-.5 mm, overall length 40.5-4.5 mm), cam position left (90 ) 564400 b STDCW` AT 0 DCW` Surface-mounted parameterisation keypad for parameter setting of the DORMA TMS door management system. With alphanumeric keys, background lighting and status LED. Activation by inputting keypad code. Connection to the DORMA TMS door management system via DCW system bus. Dimensions: 0 x 85 x mm 56400 b AT0DCW` 4 7 [ 5 8 0 6 9 # DCW` bus branching module DORMA DCW bus branching module as PC-type hub for DORMA DCW bus devices, with six terminal blocks for the DCW bus, terminals for branching the TV failsafe circuit DCW bus and four interface blocks for external door exit terminals. branching For installation in DCW junction box or enclosure by others. 56500 b module DCW` junction box DORMA DCW` junction box, IP 54, for installation of up to 4 DCW bus branching modules and/or DCW I/O modules and/or TV DCW interface DCW connectors. junction ox dimensions (W x H x D) approx. 00 x 0 x 75 mm 565000 b box ZM 08 Timer module for emergency open delay, for plug connection to TL-S TMS. Delayed release on operation of the door terminal emergency pushbutton. Delay time adjustable to 8, or 5 seconds. Immediate release by DORMA smoke switch (RM) or fire/hazard alarm control panel. 5690800 b ZM 08 Caution: Subject to special approval in Germany USV MT 700 VA Emergency power supply unit Incorporated in 0V circuit, 700 VA Enclosure dimensions (W x H x D): approx. 0 x 60 x 60 mm 050945 SVP-S x DCW` Motor lock control see SVP technical brochure 8

Specification text Order No. b DORMA TMS-Soft V.0 Parameterisation and visualisation software for running on Windows 95, 98, ME, NT, 000 or XP platform, for definition by PC of all variable functions. Parameterisation and visualisation of a DORMA TMS door management system via RS interface. Control, parameterisation and visualisation of networked DORMA TMS door management systems via DORMA LON bus system for up to doors or for up 000 doors. System requirements: PC with Pentium, min. M RAM, min. 40 M free hard disc capacity, colour graphics card, colour monitor, 56 colours, min. 800 x 600 pixel definition, CD-ROM drive, mouse, printer, one free serial interface, extension cable Windows 95, 98, ME, NT, 000, XP, null modem cable. Scope of supply: CD-ROM TMS-PC adapter for extension cable 5690 b TMS-Soft DORMA TMS LON module Module including earth/ground cable for plug-in connection of the DORMA TMS door management system to DORMA LON bus systems. TMS The module is plugged onto the TL-S TMS board. 56500 b LON module DORMA TMS LON gateway Gateway for networking up to DORMA door management systems with TMS LON modules and for connection to PC systems with DORMA TMS-Soft. Scope of supply: gateway unit power supply unit PC connection cable (null modem) TMS LON LON connection cable 56500 b gateway DORMASerialGateway- Serial LON(FTT0A) Power 9VDC -0VDC N.C. OK SerialTxD N.C. Serial RxD Service DORMA TMS LON gateway XXL Gateway as PC expansion card for networking more than 000 DORMA door management systems with TMS LON modules and connection to PC systems with DORMA TMS-Soft. Standard equipment: -off XXL gateway as expansion card TMS LON -off LON connection cable 5600 b gateway DORMA TMS LON gateway XXL-PCMCIA Gateway as PCMCIA expansion card for networking more than 000 DORMA door management systems with TMS LON modules and for connection to mobile PC systems with DORMA TMS-Soft. Standard equipment: -off XXL gateway as PCMCIA expansion card TMS LON -off LON connection cable 5600 b gateway PCC-0 Network Adapter 9

DORMA TMS Connection diagrams TL-S TMS X S RM X8 X9 SN 4 TMS X F X X 5 4 6 5 4 4 0 9 8 7 0 VAC +/-0% N L 4 VDC I max = A A A X6 X0 AT 0 DCW 4 GHI 7 PQRS Q AC 5 JKL 8 TUV 0 DEF 6 MNO 9 WXYZ # x x 0,8 x x 0,8 x x 0,8 S 0 A A X X A X S ST x DCW ST x DCW A X X X S S 0 0 S I - Y (ST) Y 4 x x 0,8 Install cable in protective ducting TV xx DCW TV xx DCW X X A X X A 0 ON S X 0 ON S X S S 0

RZ-TMS TL-S TMS X S X8 X9 S A A NT-S 4-.5 X X F A A X6 X X0 sw bn 49 rs/gr 4 rt 44 ws ge 45 gn 46 gr 4 rs 4 rt/bl 4 bl 6 vi 7 X6 0 0 S5 S4 X0 S X9 X8 X X X S S X X GND + 4 VDC SVP-S xdcw X DCW bus branching module X6 A A A X9 A X X X X0 X X X X8 A A A X8 NC X Out A A X C NO In X9 NC C Out In DCW I/O module NO X0 NC C Out NO In X NC C Out 4 ON In 4 NO S 0 S X S X6 TV 50x TL-S DCW 54 X9 ON S 0 X X X A X6 I - Y (ST) Y 4 x x 0,8 Install cable in protective ducting 9a 8 9 X X A S ON S 0 X X ON S 0 TK xx TV xx DCW TV xx DCW TK xx TV 50x DCW S A X 9 8 S X S X FK FK 0 ON A S S X S 98 S 4 X TK xx TK xx

DORMA TMS Connection diagrams TMS + SVP-Sx DCW TL-S TMS X S X8 X9 SN 4 TMS X X F X 0 VAC +/-0% N L 4 VDC I max = A A X6 A X0 ED 00 X X 5 4 F 6 5 4 4 F x x 0,8 x x 0,8 X 57 56 X0 55 54 4 5 5 5 5 50 A C S X8 7 8 R6 49 48 5 6 7 4 x x 0,8 ST x DCW A X X S S 0 sw bn 49 rs/gr 4 rt 44 ws ge 45 gn 46 gr 4 rs 4 rt/bl 4 bl 6 vi 7 X6 S S5 0 0 S4 X0 A A S X9 X8 X X X S S I - Y (ST) Y 4 x x 0,8 Install cable in protective ducting SVP-S x DCW TV xx DCW X X A NC NO C Radar 50 ma S 0 ON S X

6 4 5 7 8 TMS + TE x TE x DCW I/O module X X0 X9 X8 S NC NO C NC NO C NC NO C NC NO C Out 4 Out Out Out X S 0 ON S X A A In 4 In In In X X6 4 V DC, ma Out = Pre-alarm Out = Main alarm Out = Emergency pushbutton operated Out 4 = TV locked/unlocked In = Short-time unlocking In = Long-time unlocking In = Permanent unlocking In 4 = Re-lock Address Connection to DCW bus TMS + SVP 4xxx/ 6xxx DCW I/O module X S NC NO C Out 4 S 0 ON S X In 4 yellow pink/grey violet red/blue blue red black white SVP 4xxx X0 X9 X8 NC NO C NC NO C NC NO C Out Out Out X A A In In In X X6 SVP - A 600/000 Address 4 Connection to DCW bus GND + VDC SVP 4xxx/6xxx wiring Additional wiring for SVP 6xxx

X X PCC-0 Netw ork Adapter DORMA TMS Connection diagrams RZ TMS SVP-S 4 DCW LON Module X TL-G TMS I-Y(ST)Y x x 0,8 (max..000 m) Ensure compliance with LON specifications! LON gateway XXL PC LON gateway XXL PCMCIA LON gateway 4

DORMA TMS Safety information DORMA emergency exit systems are designed, developed and manufactured in accordance with the latest state of the art and in line with recognised technical safety regulations and standards. They meet the requirements of the code of practice entitled Requirements for electrical locking systems on doors in emergency escape routes (EltVTR, December 997 edition) published in ulletin 5/98 of the German Institute for uilding Technology, erlin. Test and approval certificates issued by the MPA NRW (Material Testing Authority) and VdS Cologne (Association of Property Insurers) are available. Compliance with the following instructions by the installer and operator is imperative to ensuring that these devices do not impede unhindered escape of persons in the event of a hazard-related emergency. Usage Emergency exit systems are electrical locking systems for doors in emergency exits and escape routes. They are designed in order to prevent improper or unauthorised usage of the associated access points. When installing and using DORMA emergency exit systems, compliance with the technical data and the requirements emanating from prevailing local conditions is essential. Preliminary building enquiry / Planning application / Approval procedure The German example Emergency exit systems do not fall under the compass of current building law and approval is subject to a discretionary exemption in the sense of 67 Musterbauordnung [Outline building regulations]. In addition, the requirements according to DIt 5/98 should also be regarded as ancillary regulations that need to be incorporated within the building approval process for the project in hand. Planning and installation A DORMA emergency exit system consists at least of the components TMS door terminal/central control station and TV electrical door locking element. Depending on the design of the emergency exit control, the following components may also be connected to the system: Key switch or access control system, monitoring and control unit, emergency escape lock with automatic locking action (switch-monitored or motor lock), flashing lamp or external alarm siren, automatic swing door operator, power pack with emergency power supply, fire alarm and/or hazard alert system, smoke switch. The electrical door locking element may only be used on emergency exit doors in conjunction with products approved by DORMA. The door terminal (local system release/emergency opening of door) should be mounted in the immediate vicinity of the door handle so that the centre of the emergency pushbutton is at a height of 850 mm to max. 00 mm above the finished floor level. The emergency pushbutton must be indicated with an adhesive label showing the inscription Emergency Exit. The adhesive label should be attached such that the arrow points to the emergency pushbutton. In buildings with automatic fire extinguishing equipment, fire alarm or other hazard alert systems, the emergency exit doors with electrical anti-tamper protection must be automatically released for escape on response or activation of these systems. If, during building usage, there is a constantly manned central control centre with a direct view of the emergency exit doors, the emergency exit release/de-activation switching operation can also be performed from this position. The properties and characteristics of the fire and smoke rated doors (fire resistance time, smoke retention/sealing function and automatic closing action) must not be impaired by the installation of the electrical door locking device. In Germany, modifications to fire doors or other fire barriers which are necessary for the installation of an electrical door locking element and which go beyond the modifications indicated as permissible in ulletin /996 of the DIt, require general building approval and/or agreement of the authorities responsible in each individual case. Consult local/national authorities for guidance. Only use DORMA spare parts or DORMA approved accessories. Any work on electrical equipment not operating on protective low voltage must always be performed by suitably qualified electricians. Installation, commissioning and maintenance work may only be performed by qualified personnel authorised by DORMA. The keys for the door terminal and emergency exit control box must be kept secure. Keys for products not operating on protective low voltage may only be handed over to suitably qualified electricians. Standards and regulations Compliance with all relevant national or regional regulations, standards, guidelines and directives (latest edition in each case) must be ensured. The following publications provide a useful general regulatory framework for ensuring system safety: DIt bulletin 5/98 Requirements for electrical locking systems on doors in emergency escape routes (EltVTR), DIt bulletin /96 Modifications to fire doors and fire rated barriers. DIN VDE 000, 0800, 085 Regulations governing the installation of electrical equipment DIN 08 Part - Regulations governing hazard alert systems for fire, burglary and robbery detection and alarm German building regulations list A, Part Special building regulations pren 67 uilding Hardware Electrically controlled emergency exit systems 5

DORMA GmbH + Co. KG P. O. ox 40 09 D-5847 Ennepetal reckerfelder Strasse 4-48 D-5856 Ennepetal Germany Tel. +49(0) /79-0 Fax +49(0) /79 4 95 The address of a subsidiary/ representation in your area you can find at the DORMA website: www.dorma.com Subject to change without notice WN 05 0 055, 07/0,, X. XX/CtP. 08/0