Adaptability to Enhanced Security

Transcription

1 Installer Guide

2

3 Adaptability to Enhanced Security AdapTec Plus combines power supply and door access controller features in a compact casing for an encrypted and secure I/O function, enhancing door access control functionalities and easing installation processes. AdapTec Plus is an exceptional FingerTec accessory in a small package! understanding adaptec plus FUNCTIONS Enhanced Security with Encrypted Signals It supports FingerTec encrypted 6-bit Wiegand communication output; providing enhanced security level for extra protection. Power Up Terminals & Door Lock Systems A single AdapTec Plus can support a maximum of units of FingerTec terminals and sets of door lock accessories such as the EM lock and drop bolt in one single system installation. Prolonged Life Span of Hardware With data encryption, the life span of the terminals can be prolonged without the risk of short-circuiting when using AdapTec Plus Control IN/OUT Terminals at an Entrance AdapTec Plus is a perfect choice for an IN/OUT installation, where a door is controlled both at the entrance and the exit. Supports Rechargeable Backup Battery Connects well to any VDC rechargeable backup battery, providing power to ensure protection of access during any events of power failure.

4 Emergency Alerts with Siren Compatible with an NC siren type with a maximum of 0.5A load for an emergency event e.g. if the terminal is being dismantled without authorization. Seamless Integration with FingerTec Terminals Mix and match the FingerTec terminals via AdapTec Plus for a cost effective access control system suitable for small and medium sized offices. UNDERSTANDING THE TECHNICAL SPECIFICATIONS Surface finishing Dimension, mm x 49 x 4 Weight, kg 0.6 CPU Power input Power output Backup Power system Input signal Output signal Over input voltage Door release Door force open Illegal dismantle FingerTec terminals Door unlock timer On Board LED indicators Over voltage alarm Fuses Battery cut-off PHYSICAL APPEARANCE Acrylonitrile Butadiene Styrene (ABS) High Performance RISC CPU POWER SUPPLY AC 0 ~ 40V (Universal Input) VDC A UPS or VDC Rechargeable battery INPUT OUTPUT SIGNAL 6-bit FingerTec encrypted Weigand signal VDC 0.5A Siren VDC A EM output (NO/NC Type door locks) ALERTS & NOTIFICATIONS Yes, long beeps Yes, short beeps Yes, continuous beeps (May opt to output external siren system) Yes, continuous beeps (May opt to output external siren system) VR type, LED blinks to indicate unlock time in Seconds. EM LED lit up door lock output is working. Status LED lit up CPU is working. Battery low LED lit up Battery is low and cut-off. ON BOARD PROTECTION >5 VDC PTC type 8.5 ~ 9.5 VDC NOTE: Specifications are subject to change. Check for latest product information.

5 understanding THE DESIGN AdapTec Plus consists of main modules 4 Power supply/power input module Door lock timer Power output/access control module 4 LED status indicator Power supply/power input module This portion is to be connected to a power source with AC0~40V. An AC current should be supplied into this side and a VDC A current will be generated as output. These two cables, -V and +V are default and are connected to the inner part of AdapTec. Please do not remove or change these cables. Power output/access control module These cables connect to the VDC power from the power supply/input module. Do not remove or dismantle these cables. 4 These cables connect to a VDC rechargeable backup battery. During a power failure, the backup battery will power up AdapTec Plus. 5 These are the power output ports from AdapTec Plus. Refer to the wiring diagram for details. 6 These are the Wiegand data input ports from the FingerTec terminals. Refer to the wiring diagram for details. 5

6 Other Features You will find a buzzer, 4 LED indicators, and a door lock timer on the board. Check and set each of them accordingly after powering up the system. 4 You will hear the buzzer beep to indicate: Unlocked Door (Short buzz) Door is unlocked and access granted (during verification or pressing push release button). Over Voltage (Non-stop buzzing after startup) Over voltage of power input (Stop the power supply to the system immediately and check the input voltage, consult support@fingertec.com) Adjust the door lock timer for a longer or shorter unlocking time period by turning the screw clockwise. Count the LED blinks after turning it. Each blink represents second and the recommended time period is 5 seconds (5 blinks). Select the type of door lock to use, NO type or NC type. PIN & NO Type door lock system. PIN & NC Type door lock system (default) 4 The LED lights up to indicate the following: EM lock LED - The EM lock system is charged up and working properly. Status LED - The overall system is working properly. Note: Contact support@fingertec.com if either of the above LED lights are not lit up. Bat Low LED - The battery is weak and needs to be charged or replaced. 6

7 DETAILS OF WIRING AdapTec Plus supports types of installations, Convenient or Secure. You can select between modes by applying different wiring arrangements during installation. Under Convenient mode, AdapTec Plus will unlock doors immediately after receiving responses from FingerTec devices. This feature is supw ported by all FingerTec models. WelcomeCheck-In :00 Sun MENU ESC For installations using Secure mode, there will be a s time delay when unlocking the door after verification at FingerTec devices. This delay is due to the 6-bit Wiegand transmission of encrypted password from device to AdapTec Plus. This is an optional security feature provided by AdapTec Plus for users who favor more security (slight delay) over convenience (no delays). OK R Qi 6 AdapTec Plus works with FingerTec terminals via an encrypted Wiegand signal to control the door open-close mechanism. Please make sure you are w using the following FingerTec models that support the encrypted 6-bit Wiegand signal to work with the AdapTec Plus to setup a door lock system: WelcomeCheck-In :00 Sun MENU ESC 6 OK R Qi 4 w WelcomeCheck-In :00 Sun MENU ESC WelcomeCheck-In :00 Sun -0-0 SUN 6 R Qi w WelcomeCheck-In :00 Sun w OK MENU MENU ESC 6 OK ESC 6 OK Hi Qi Qi AC900 R -0-0 R m-kadex R Qi Kadex SUN Hi Hi -0-0 Face ID Face ID i-kiosk 00 Plus SUN Step Look for the power input port on the FingerTec terminal. Normally the connection ports on the terminals are marked as PWR/+V (red wire) and GND (black wire) SUN SUN Hi Convenient Installation: See diagram, page 8 for details. Secure Installation: See diagram, page 8 for details. Step Convenient Installation: Look for the door lock output port NO and GND from the terminal. Secure Installation: Look for the Wiegand output port, WDO (green), WD (white) and GND (black) from the terminal. Step Connect the wires from the terminals to AdapTec Plus. Step 4 Connect the wires from AdapTec Plus to the door lock system. Hi Hi (See diagram, page 8 for details). (Ignore this if you only want to use the system for time attendance purposes) Step 5 Connect AdapTec Plus to a VDC rechargeable backup battery. (See diagram, page 8 for details). (This is optional. Ignore this if you do not need any backup power). Step 6 Connect AdapTec Plus to a power source (VDC A).

8 WIRING DIAGRAMS Convenient Installation AdapTec Plus Tamper Siren EM +V Siren Exit Data Switch Out Lock Out Mute Switch D D0 GND EM + Lock Emergency Break Glass ON-OFF C Key Switch D V NO COM Connection Points Exit Button WIRING DIAGRAMS SECURE Installation AdapTec Plus Tamper Siren EM +V Siren Exit Data Switch Out Lock Out Mute Switch D D0 EM + Lock Emergency GND V Exit Button GND WD WD0 Break Glass ON-OFF C Key Switch D Connection Points Connection Points 8

9 Connecting adaptec plus to an ALARM SIREN For all FingerTec door access control models, there is a security button behind the terminal. During normal operation, the security button is compressed and once the terminal is dismantled, the button will be released and a System broken message will appear onscreen. During the release of the button, the terminal will output an alarm signal. However, no alarm sound will be emitted if the terminal is not equipped with an external siren. To use the siren feature, we recommend that you install an additional alarm siren and connect it to the FingerTec terminals. Benefits of Using AdapTec Plus with Alarm Siren We recommend that you install a terminal along with AdapTec Plus if you plan to use the alarm siren. In AdapTec Plus, an additional port is readily built to receive the alarm signal from the FingerTec terminals. AdapTec Plus has an output of VDC and it is suitable for use with an alarm siren that has the same power input. You do not need to source an additional VDC power supply for this purpose. Furthermore, AdapTec Plus comes with a Siren Mute button where you can press the button to deactivate the alarm siren when required. WIRING DIAGRAMS Alarm siren R, Kadex, m-kadex, Hi and Face ID AdapTec Plus Tamper Siren EM +V Siren Exit Data Switch Out Lock Out Mute Switch D D Alarm Siren ALM + ALM ---- Siren Mute Button Connection Points GND V Remark: Set Auto Alarm in terminal to N. Menu > Options > Sys Opt > Adv Opt > Auto Alarm > N. 9

10 WIRING DIAGRAMS 4 Alarm siren AC900 AdapTec Plus Tamper Siren EM +V Siren Exit Data Switch Out Lock Out Mute Switch D D Alarm Siren ALM + ALM ---- Siren Mute Button Connection Points GND V Remark: Set Auto Alarm in terminal to N. Menu > Options > Sys Opt > Adv Opt > Auto Alarm > N. WIRING DIAGRAMS 5 Alarm siren Face ID, Qi and i-kiosk 00 Plus AdapTec Plus Tamper Siren EM +V Siren Exit Data Switch Out Lock Out Mute Switch D D Alarm Siren COM NO Siren Mute Button Connection Points GND V Deactivating the Alarm Siren:. At the terminal, press Menu and select Turn Off Alarm to turn off the alarm siren.. To deactivate the alarm siren of Adaptec Plus, press the Siren Mute Button that is connected to the Adaptec Plus. This will turn off the alarm siren function in the Adaptec Plus. 0

11 understanding AdapTec plus installation for Wooden Door or Glass Door The diagrams below only highlights the use of an EM lock during installation. You may opt to use a dropbolt/deadbolt/door strike instead. Please consult a qualified technician/installer before proceeding with the installation. WALL Back Steel Plate Screws 4 feet /. meter (recommended) To install FingerTec AC900/R on a wall, drill 5 holes as shown. 4 small holes are for the screws and the bigger hole is for the network cable. Tighten the 4 screws to fix the Back Steel Plate on the wall. Install the keyswitch as per instructions given in the box. The keyswitch is an override key in case of a system failure or breakdown. Silver Nut Wooden Doorframe Steel Bar Allen Key Screw Wooden Door Drill holes on the wooden door. Place the Steel Bar on the door. Insert the Silver Nut on one side and the Allen Key Screw on the other side. Tighten the screw to lock the Steel Bar onto its position.

12 Glass Doorframe U-Bracket Allen Key Screws Philip Screw Allen Key Screws Steel Bar Glass Door Lodge the U-Bracket into the upper edge of the glass doorframe. Tighten the 4 Allen Key Screws to hold the U-Bracket into position. Place the Steel Bar on the side of the U-Bracket. Tighten the Philip Screws to lock the Steel Bar onto position. Doorframe Screws Magnet Aluminum Plate Allen Key Screws Drill 4 holes on the wooden frame. Tighten the 4 screws to fix the Aluminum Plate properly on the doorframe. Use the Allen Key to tighten the screws at the bottom of the Magnet. The Magnet will stick to the Aluminum Plate when the screws are tightened. Use the Allen Key to tighten the other screws on the sides of the Magnet.

13 MENU R OK ESC ERVIEW OF THE WHOLE SYSTEM INSTALLATION AC0/40V Power Input Switching power supply VDC VDC Rechargeable battery ON-OFF Keyswitch ABE CEILING CEILING w EM Lock Emergency Break Glass Hub/Switch FingerTec Terminal Push Button PC OUTDOOR INDOOR NETWORKING

14 fingertec accessories For more accessories go to accessory.fingertec.com. AdapTec Plus HID Card / MiFare Card / RFID Card ON-OFF Keyswitch RFID Key Chain EM 600 / EM 00 Contactless Release Button Alarm Siren with Strobe Light Emergency Break Glass Release Button mounting an adaptec plus onto a wall Mount the AdapTec Plus on a wall Identify a location to mount the AdapTec Plus on a wall. Fix the AdapTec Plus onto the wall by tightening the screws into the 4 holes. 4

15 5