SolarEdge. Installation Guide. For Europe & APAC Version 3.1

SlarEdge Installatin Guide Fr Eurpe & APAC Versin 3.1

Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may be reprduced, stred in a retrieval system r transmitted, in any frm r by any means, electrnic, mechanical, phtgraphic, magnetic r therwise, withut the prir written permissin f SlarEdge Inc. The material furnished in this dcument is believed t be accurate and reliable. Hwever, SlarEdge assumes n respnsibility fr the use f this material. SlarEdge reserves the right t make changes t the material at any time and withut ntice. Yu may refer t the SlarEdge web site (www.slaredge.cm) fr the mst updated versin. All cmpany and brand prducts and service names are trademarks r registered trademarks f their respective hlders. Patent marking ntice: see http://www.slaredge.cm/grups/patent The general terms and cnditins f delivery f SlarEdge shall apply. The cntent f these dcuments is cntinually reviewed and amended, where necessary. Hwever, discrepancies cannt be excluded. N guarantee is made fr the cmpleteness f these dcuments. The images cntained in this dcument are fr illustrative purpses nly and may vary depending n prduct mdels. Emissin Cmpliance This equipment has been tested and fund t cmply with the limits applied by the lcal regulatins. These limits are designed t prvide reasnable prtectin against harmful interference in a residential installatin. This equipment generates, uses and can radiate radi frequency energy and, if nt installed and used in accrdance with the instructins, may cause harmful interference t radi cmmunicatins. Hwever, there is n guarantee that interference will nt ccur in a particular installatin. If this equipment des cause harmful interference t radi r televisin receptin, which can be determined by turning the equipment ff and n, yu are encuraged t try t crrect the interference by ne r mre f the fllwing measures: Rerient r relcate the receiving antenna. Increase the separatin between the equipment and the receiver. Cnnect the equipment int an utlet n a circuit different frm that t which the receiver is cnnected. Cnsult the dealer r an experienced radi/tv technician fr help. Changes r mdificatins nt expressly apprved by the party respnsible fr cmpliance may vid the user s authrity t perate the equipment. 1

Supprt and Cntact Infrmatin Supprt and Cntact Infrmatin If yu have technical prblems cncerning SlarEdge prducts, please cntact us: Cuntry Phne E-Mail Australia (+61) 1800 465 567 supprt@slaredge.net.au APAC (Asia Pacific) supprt-asia@slaredge.cm Belgium (+32) 080073041 supprt@slaredge.be France (+33) 0800917410 supprt@slaredge.fr Germany (+49) 089-45459730 supprt@slaredge.de Italy (+39) 800 784 824 supprt@slaredge.it Japan (+81) 03-6261-1274 supprt@slaredge.jp US & Canada (+1) 877-360-5292 ussupprt@slaredge.cm United Kingdm (+44) 0800 028 1183 supprt@slaredge.uk Greece (+30) 0800-125574 Israel(+972) 073 240-3122 Netherlands (+31) 08000221089 supprt@slaredge.cm Wrldwide (+972) 073 240-3118 Fax (+972) 073 240-3117 Befre cntact, make sure t have the fllwing infrmatin at hand: Inverter and pwer ptimizer mdel. Serial number f the prduct in questin. The errr indicated n the inverter screen r n the SlarEdge mnitring prtal, if there is such an indicatin. System cnfiguratin infrmatin, including the type and number f mdules cnnected and the number and length f strings. The cmmunicatin methd t the SlarEdge server, if the site is cnnected. The inverter sftware versin as appears in the ID status (see ID Status n page 50). 2

Supprt and Cntact Infrmatin Cntents Disclaimers 1 Imprtant Ntice 1 Emissin Cmpliance 1 Supprt and Cntact Infrmatin 2 HANDLING AND SAFETY INSTRUCTIONS 6 SAFETY SYMBOLS 6 IMPORTANT SAFETY INSTRUCTIONS 7 Chapter 1: Intrducing the SlarEdge Pwer Harvesting System 9 SlarEdge Pwer Optimizer 9 SlarEdge Inverter 9 SlarEdge Mnitring Prtal 9 Installatin Prcedure 10 Installatin Equipment List 10 Inverter Transprt and Strage 11 Chapter 2: Installing the Pwer Optimizers 12 Safety 12 Installatin Guidelines 13 Step 1: Munting the Pwer Optimizers 14 Step 2: Cnnecting a PV Mdule t a Pwer Optimizer 15 Step 3: Cnnecting Pwer Optimizers in Strings 15 Step 4: Verifying Prper Pwer Optimizer Cnnectin 16 Chapter 3: Installing the Inverter 18 Inverter Package Cntents 18 Identifying the Inverter 18 Inverter Interfaces 18 Munting the Inverter 20 Chapter 4: Cnnecting the AC and the Strings t the Inverter 25 Grid Cnnectin Guidelines 25 Cnnecting the AC Grid t the Inverter 25 Cnnecting the Strings t the Inverter 27 Selecting a Residual Current Device (RCD) 28 Chapter 5: Cmmissining the Installatin 29 Step 1: Activating the System 29 Step 2: Pairing Pwer Optimizers t the Inverter 31 Step 3: Verifying Prper Operatin 33 Step 4: Reprting and Mnitring Installatin Data 34 The SlarEdge Mnitring System 34 Prviding Installatin Infrmatin 35 Paper Template 35 Site Mapper 35 Creating a Site in the SlarEdge Mnitring Prtal 35 Chapter 6: User Interface 36 3

Supprt and Cntact Infrmatin LCD User Buttns 36 Inverter Cnfiguratin Setup Mde 37 Cnfiguring the Inverter Using the Internal LCD User Buttns 37 Cnfiguring the Inverter Using the LCD Light Buttn 39 Cnfiguratin Menu Optins 42 Cuntry and Grid 42 Language 42 Cmmunicatin 43 Pwer Cntrl 45 Display 45 Maintenance 46 Infrmatin 46 Status Screens - Operatinal Mde 48 Initial Status 48 Main Inverter Status 48 Energy Meter Status 49 Telemetry Status 50 ID Status 50 Server Cmmunicatin Status 50 IP Status 51 ZigBee Status 51 Wi-Fi Status 51 Cmmunicatin Prts Status 52 Fan Status 52 Pwer Cntrl Status 54 Chapter 7: Setting Up Cmmunicatin 55 Cmmunicatin Types 55 Cmmunicatin Cnnectrs 55 Remving the Inverter Cver 56 Creating an Ethernet (LAN) Cnnectin 57 Creating an RS485 Bus Cnnectin 60 Creating a Wireless ZigBee Cnnectin 64 Creating a Wi-Fi Cnnectin 64 Verifying the Cnnectin 65 Appendix A: Errrs and Trubleshting 66 Trubleshting Cmmunicatin - S_OK is Nt Displayed 66 Trubleshting Ethernet Cmmunicatin 66 Trubleshting RS485 Cmmunicatin 68 Additinal Trubleshting 69 Errr Cdes 69 Pwer Optimizer Trubleshting 78 Appendix B: Technical Specificatins 81 Technical Specificatins - Three Phase Inverters 86 4

Supprt and Cntact Infrmatin SE4KSE4K mdel is available in sme cuntries; refer t the Certificatins categry in http://www.slaredge.cm/grups/supprt/dwnlads - SE12.5K 86 SE15K - SE33.3KThe SE33.3K mdel requires a medium vltage transfrmer 90 DC Safety Unit Specificatins 95 Appendix C: Mechanical Specificatins 96 Single Phase Inverter and Munting Bracket Type 1 96 Single Phase Inverter and Munting Bracket Type 2 98 Three Phase Inverter and Munting Bracket Type 1 100 Three Phase Inverter and Munting Bracket Type 2 102 Appendix D: Cnnecting the AC and DC Strings t the DC Safety Unit 103 Cnnecting the AC Grid t the Inverter 104 Cnnecting the Strings t the DC Safety Unit 105 Appendix E: Safe DC 108 Appendix F: External Fan Maintenance and Replacement 109 Fan Maintenance 109 External Fan Replacement 109 Appendix G: Replacing and Adding System Cmpnents 111 Replacing an Inverter 111 Adding, Remving, r Replacing Pwer Optimizers 111 5

HANDLING AND SAFETY INSTRUCTIONS HANDLING AND SAFETY INSTRUCTIONS During installatin, testing and inspectin adherence t all the handling and safety instructins is mandatry. SAFETY SYMBOLS The fllwing safety symbls are used in this dcument. Familiarize yurself with the symbls and their meaning befre installing r perating the system. WARNING! Dentes a hazard. It calls attentin t a prcedure that, if nt crrectly perfrmed r adhered t, culd result in injury r lss f life. D nt prceed beynd a warning nte until the indicated cnditins are fully understd and met. CAUTION! Dentes a hazard. It calls attentin t a prcedure that, if nt crrectly perfrmed r adhered t, culd result in damage r destructin f the prduct. D nt prceed beynd a cautin sign until the indicated cnditins are fully understd and met. NOTE Dentes additinal infrmatin abut the current subject. IMPORTANT SAFETY FEATURE Dentes infrmatin abut safety issues. 6

IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING! The inverter cver must be pened nly after shutting ff the inverter ON/OFF switch lcated at the bttm f the inverter. This disables the DC vltage inside the inverter. Wait five minutes befre pening the cver. Otherwise, there is a risk f electric shck frm energy stred in the capacitrs. WARNING! Befre perating the inverter, ensure that the inverter AC pwer cable and wall utlet are grunded prperly. WARNING! Opening the inverter and repairing r testing under pwer must be perfrmed nly by qualified service persnnel familiar with this inverter. WARNING! D nt tuch the PV panels r any rail system cnnected when the inverter switch is ON, unless grunded. CAUTION! This unit must be perated under the specified perating specificatins, as described in the latest technical specificatin datasheet, available n the SlarEdge website at http://www.slaredge.cm/grups/prducts/verview. CAUTION! The inverters are IP65 rated. Unused cnnectrs and glands shuld be sealed with the prvided seals. NOTE Use PV mdules rated accrding t IEC 61730 class A. NOTE The symbl appears at grunding pints n the SlarEdge equipment. This symbl is als used in this manual. 7

IMPORTANT SAFETY INSTRUCTIONS NOTE The fllwing warning symbls appear n the inverter warning label: Risk f electric shck Risk f electric shck frm energy stred in the capacitr. D nt remve cver until 5 minutes after discnnecting all surces f supply. Ht surface T reduce the risk f burns, d nt tuch. 8

Chapter 1: Intrducing the SlarEdge Pwer Harvesting System Chapter 1: Intrducing the SlarEdge Pwer Harvesting System The SlarEdge pwer harvesting slutin maximizes the pwer utput frm any type f slar Phtvltaic (PV) installatin while reducing the average cst per watt. The fllwing sectins describe each f the system s cmpnents. SlarEdge Pwer Optimizer The SlarEdge pwer ptimizers are DC-DC cnverters cnnected t PV mdules in rder t maximize pwer harvesting by perfrming independent Maximum Pwer Pint Tracking (MPPT) at the mdule level. The pwer ptimizers regulate the string vltage at a cnstant level, regardless f string length and envirnmental cnditins. The pwer ptimizers include a safety vltage functin that autmatically reduces the utput f each pwer ptimizer t 1 Vdc in the fllwing cases: During fault cnditins The pwer ptimizers are discnnected frm the inverter The inverter s ON/OFF switch is turned OFF Each pwer ptimizer als transmits mdule perfrmance data ver the DC pwer line t the inverter. Tw types f pwer ptimizers are available: Mdule Add-n pwer ptimizer cnnected t ne r mre mdules Smart mdules - the pwer ptimizers are embedded int a mdule SlarEdge Inverter The SlarEdge inverter efficiently cnverts DC pwer frm the mdules int AC pwer that can be fed int the main AC service f the site and frm there t the grid. The inverter als receives the mnitring data frm each pwer ptimizer and transmits it t a central server (the SlarEdge mnitring prtal; requires Internet cnnectin). Sme inverters are available with an ptinal DC Safety Unit. The DC Safety Unit is a manually perated switch fr discnnecting the DC pwer f a SlarEdge system. The DC Safety Unit is lcated belw the inverter and is cnnected t the inverter with AC and DC wires. SlarEdge Mnitring Prtal The SlarEdge mnitring prtal enables mnitring the technical and financial perfrmance f ne r mre SlarEdge sites. It prvides past and present infrmatin n the system perfrmance bth at the system and mdule levels. 9

Installatin Prcedure Installatin Prcedure The fllwing is the prcedure fr installing and setting up a new SlarEdge site. Many f these als apply t mdificatin f an existing site. 1. Cnnecting Pwer Optimizers in Strings, page 15 2. Recrding pwer ptimizer serial numbers (ptinal), page 35 3. Munting the inverter, 20 4. Cnnecting the AC and the Strings t the Inverter, page 25, r Cnnecting the AC and the String t the DC Safety Unit, page 104. 5. Cmmissining and activating the installatin, page 29 6. Cnnecting the inverter t the SlarEdge mnitring prtal, page 35 7. Cnfiguring the inverter, page 36 Installatin Equipment List Standard tls can be used during the installatin f the SlarEdge system. The fllwing is a recmmendatin f the equipment needed fr installatin: Allen screwdriver fr 5mm screw type fr the inverter cver and Safety Switch cver Allen screwdriver fr 5mm screw type fr the inverter side screw Allen screwdriver fr M6/M8 screw types Standard flat-head screwdrivers set Nn-cntact vltage detectr Crdless drill r screwdriver and bits suitable fr the surface n which the inverter will be installed Suitable hardware fr attaching the inverter munting bracket t the surface t which it will be cnnected M6 (1/4") r M8 (5/16 ) stainless blts, nuts, and washers fr attaching the pwer ptimizer t the racking (nt required fr smart mdules) MC4 crimper Wire cutters Wire strippers Vltmeter 10

Chapter 1: Intrducing the SlarEdge Pwer Harvesting System Fr installing the cmmunicatin ptins, yu may als need the fllwing: Fr Ethernet: CAT5/6 twisted pair Ethernet cable with RJ45 cnnectr. If using a CAT5/6 cable spl: RJ45 plug and RJ45 crimper Fr RS485: Fur- r six-wire shielded twisted pair cable. Watchmaker precisin screwdriver set Inverter Transprt and Strage Transprt the inverter in its riginal packaging, facing up and withut expsing it t unnecessary shcks. If the riginal package is n lnger available, use a similar bx that can withstand the weight f the inverter (refer t the inverter weight in Technical Specificatins n page 81), has a handle system and can be clsed fully. Stre the inverter in a dry place where ambient temperatures are -25 C - +65 C / -13 F - 149 F. 11

Chapter 2: Installing the Pwer Optimizers Chapter 2: Installing the Pwer Optimizers Safety The fllwing ntes and warnings apply when installing the pwer ptimizers. mdules: WARNING! When mdifying an existing installatin, turn OFF the inverter ON/OFF switch and the AC circuit breaker n the main AC distributin panel. WARNING! Input and utput cnnectrs are nt watertight until mated. Open cnnectrs shuld be mated t each ther r plugged with apprpriate watertight caps. CAUTION! This unit must be perated accrding t the perating specificatins in this dcument. CAUTION! All PV mdules must be cnnected t a pwer ptimizer. CAUTION! Cutting the pwer ptimizer input r utput cable cnnectr is prhibited and will vid the warranty. CAUTION! Pwer ptimizers are IP65/NEMA4 rated. Chse a munting lcatin where ptimizers will nt be submerged in water. CAUTION! If yu intend t munt the ptimizers directly t the mdule r mdule frame, first cnsult the mdule manufacturer fr guidance regarding the munting lcatin and the impact, if any, n mdule warranty. Drilling hles in the mdule frame shuld be dne accrding t the mdule manufacturer instructins. 12

Chapter 2: Installing the Pwer Optimizers CAUTION! Installing a SlarEdge system withut ensuring cmpatibility f the mdule cnnectrs with the ptimizer cnnectrs may be unsafe and culd cause functinality prblems such as grund faults, resulting in inverter shut dwn. In rder t ensure mechanical cmpatibility f the SlarEdge ptimizers and the mdules t which they are cnnected: Use identical cnnectrs frm the same manufacturer and f the same type n bth the pwer ptimizers and n the mdules; r Verify that the cnnectrs are cmpatible in the fllwing way: The cnnectr manufacturer shuld explicitly verify cmpatibility with the SlarEdge ptimizer cnnectr; and A third-party test reprt by ne f the listed external labs (TUV, VDE, Bureau Veritas UL, CSA, InterTek) shuld be btained, verifying the cmpatibility f the cnnectrs. IMPORTANT SAFETY FEATURE Mdules with SlarEdge pwer ptimizers are safe. They carry nly a lw safety vltage befre the inverter is turned ON. As lng as the pwer ptimizers are nt cnnected t the inverter r the inverter is turned OFF, each pwer ptimizer will utput a safe vltage f 1V. Installatin Guidelines The steps in this chapter refer t mdule add-n pwer ptimizers. Fr smart mdules, start frm Step 3: Cnnecting Pwer Optimizers in Strings n page 15. Als refer t the dcumentatin supplied with the smart mdules. The pwer ptimizer can be placed in any rientatin. Psitin the pwer ptimizer clse enugh t its mdule s that their cables can be cnnected. T allw fr heat dissipatin, maintain a 2.5 cm/ 1" clearance distance between the pwer ptimizer and ther surfaces. The minimum and maximum string length guidelines are stated in the pwer ptimizer datasheets. Refer t the SlarEdge Site Designer fr string length verificatin. The SlarEdge Site Designer is available n the SlarEdge website at http://www.slaredge.cm/grups/supprt/dwnlads, under Sftware Tls. 13

Step 1: Munting the Pwer Optimizers Cmpletely shaded mdules may cause their pwer ptimizers t temprarily shut dwn. This will nt affect the perfrmance f the ther pwer ptimizers in the string, as lng as the minimum number f unshaded pwer ptimizers cnnected in a string f mdules is met. If under typical cnditins fewer than the minimum ptimizers are cnnected t unshaded mdules, add mre ptimizers t the string. D nt leave the pwer ptimizers cnnectrs discnnected. Open cnnectrs shuld be mated t each ther. NOTE The images cntained in the fllwing sectins are fr illustrative purpses nly and may vary depending n prduct mdels. Step 1: Munting the Pwer Optimizers Fr each f the pwer ptimizers 1 : 1. Determine the pwer ptimizer munting lcatin and use the pwer ptimizer munting brackets t attach the pwer ptimizer t the supprt structure. Fr frame-munted pwer ptimizers fllw the instructins supplied with the ptimizers. 2. If required, mark the munting hle lcatins and drill the hle. CAUTION! D nt drill thrugh the pwer ptimizer r thrugh the munting hles. The drilling vibratins can damage the pwer ptimizer and will vid the warranty. 3. Attach each pwer ptimizer t the rack using the M6 (1/4'') stainless steel blts, nuts and washers. Apply trque f 9.5 N*m / 7 lb*ft. 4. Verify that each pwer ptimizer is securely attached t the supprting structure r the mdule. NOTE Recrd pwer ptimizer serial numbers and lcatins, as described in Prviding Installatin Infrmatin n page 35. 1 Nt applicable t smart mdules. 14

Chapter 2: Installing the Pwer Optimizers Step 2: Cnnecting a PV Mdule t a Pwer Optimizer Fr each f the pwer ptimizers 1 : Cnnect the Plus (+) utput cnnectr f the mdule t the Plus (+) input cnnectr f the pwer ptimizer. Cnnect the Minus (-) utput cnnectr f the mdule t the Minus (-) input cnnectr f the pwer ptimizer. NOTE Figure 1: Pwer ptimizer cnnectrs Images are fr illustratin purpses nly. Refer t the label n the prduct t identify the plus and minus input and utput cnnectrs. Step 3: Cnnecting Pwer Optimizers in Strings Yu can cnstruct parallel strings f unequal length, that is, the number f pwer ptimizers in each string des nt have t be the same. The minimum and maximum string lengths are specified in the pwer ptimizer datasheets. Refer t the SlarEdge Site Designer fr string length verificatin. NOTE The ttal cable length f the string (including pwer ptimizers cables) shuld nt exceed 1000ft./300m frm DC+ t DC- f the inverter. Use at least 11 AWG/ 4 mm² DC cables. 1 Nt applicable t smart mdules. 15

Step 4: Verifying Prper Pwer Optimizer Cnnectin 1. Cnnect the Minus (-) utput cnnectr f the string s first pwer ptimizer t the Plus (+) utput cnnectr f the string s secnd pwer ptimizer. 2. Cnnect the rest f the pwer ptimizers in the string in the same manner. Figure 2: Pwer ptimizers cnnected in series 3. If yu intend t mnitr the installatin, using the SlarEdge mnitring prtal, recrd the physical lcatin f each pwer ptimizer, as described in Prviding Installatin Infrmatin n page 35. WARNING! Input and utput cnnectrs are nt watertight until mated. Open cnnectrs shuld be mated t each ther r plugged with apprpriate watertight caps. Step 4: Verifying Prper Pwer Optimizer Cnnectin After a mdule is cnnected t a pwer ptimizer, the pwer ptimizer utputs a safe vltage f 1V. Therefre, the ttal string vltage shuld be equal t 1V times the number f pwer ptimizers cnnected in series in the string. Fr example, if 10 pwer ptimizers are cnnected in a string, then 10V shuld be prduced. Make sure the mdules are expsed t sunlight during this prcess; therwise, the pwer ptimizers may nt be pwered. If yu use a tracker, the pwer ptimizer will turn ON nly if the tracker is tracking the sun and the mdule prvides at least 2W. 16

Chapter 2: Installing the Pwer Optimizers In SlarEdge systems, due t the intrductin f pwer ptimizers between the PV mdules and the inverter, the shrt circuit current I SC and the pen circuit vltage V OC hld different meanings frm thse in traditinal systems. Fr mre infrmatin abut the SlarEdge system s string vltage and current, refer t the V OC and I SC in SlarEdge Systems Technical Nte, available n the SlarEdge website at: http://www.slaredge.cm/files/pdfs/isc_and_vc_in_slaredge_systems_technical_ nte.pdf T verify prper pwer ptimizers cnnectin: Measure the vltage f each string individually befre cnnecting it t the ther strings r t the inverter. Verify crrect plarity by measuring the string plarity with a vltmeter. Use a vltmeter with at least 0.1V measurement accuracy. Fr trubleshting pwer ptimizer peratin prblems, refer t Pwer Optimizer Trubleshting n page 78. 17

Chapter 3: Installing the Inverter Chapter 3: Installing the Inverter Install the inverter either befre r after the mdules and pwer ptimizers have been installed. CAUTION! D nt rest the cnnectrs at the bttm f the inverter n the grund, as it may damage them. T rest the inverter n the grund, lay it n its back, frnt r side. Inverter Package Cntents l One SlarEdge inverter l One munting bracket l Tw Allen screws fr fastening the inverter t the munting bracket l installatin guide (with activatin card and instructins) Identifying the Inverter Refer t the sticker n the inverter that specifies its Serial Number and its Electrical Ratings. Prvide the serial number when cntacting SlarEdge supprt. The serial number is als required when pening a new site in the SlarEdge mnitring prtal. In the fllwing sectins, unless therwise indicated, instructins apply t bth single-phase and three-phase inverters, thugh nly ne graphical example may be presented. Inverter Interfaces The fllwing figure shws the inverter cnnectrs and cmpnents, lcated at the bttm f the inverter. The ON/OFF switch and the LCD light buttn may vary depending n the inverter mdel: Figure 3: Inverter Interfaces 18

Chapter 3: Installing the Inverter LCD panel: displays inverter infrmatin and cnfiguratin parameters LCD LEDs: Three LEDs indicate the fllwing inverter statuses: Clr Descriptin Functinality Green Yellw Red Pwer prductin Mdule cmmunicatin and inverter shutdwn Fault On - The inverter is prducing pwer. Blinking - Standby mde. The inverter is in Standby mde until its wrking vltage is reached. The inverter then enters Prductin mde and prduces pwer. Off - The inverter is nt prducing pwer. This may be during Night mde, when the inverter ON/OFF switch is OFF r when an errr ccurs. Blinking: Mnitring infrmatin is being received frm a pwer ptimizer. The inverter is being shut dwn. On - There is an errr. Refer t Errrs and Trubleshting n page 66 fr mre infrmatin. Blinking - The inverter is being shut dwn. All LEDs turn n while the inverter is being cnfigured. Figure 4: Inverter frnt view 19

Munting the Inverter AC utput: AC cable external gauge: Single phase inverters: PG21 (9-16mm diameter) Three phase inverters: M32 (15-21mm diameter) DC inputs: Fr cnnectin f the PV installatin CAUTION! D nt remve the six screws n the DC metal panel as it may harm the inverter sealing and vid the warranty. ON/OFF switch: Turning this switch ON starts the peratin f the pwer ptimizers, enables pwer prductin and allws the inverter t begin exprting pwer t the utility grid. Turning it OFF reduces the pwer ptimizer vltage t a lw safety vltage and inhibits exprtatin f pwer. When this switch is OFF, the inverter cntrl circuitry remains pwered up. LCD light buttn: Pressing this buttn lights up the LCD fr 30 secnds. In additin, yu can press this buttn t access cnfiguratin menu ptins, as described Cnfiguring the Inverter Using the LCD Light Buttn n page 39. Tw cmmunicatin glands, fr cnnectin f inverter cmmunicatin ptins. Each gland has three penings. Refer t Setting Up Cmmunicatin n page 55 fr mre infrmatin. Munting the Inverter The inverter is supplied with ne f the fllwing tw types f munting brackets. The munting steps in the next sectins refer t these types. Figure 5: Munting bracket types NOTE Make sure the munting surface r structure can supprt the weight f the inverter and bracket, and make sure that it spans the width f the bracket. 20

Chapter 3: Installing the Inverter CAUTION! HEAVY OBJECT. T avid muscle strain r back injury, use prper lifting techniques, and if required - a lifting aid when remving r replacing. 1. Determine the inverter munting lcatin, n a wall, stud framing r ple. T allw prper heat dissipatin, maintain the fllwing minimum clearance areas between the inverter and ther bjects: If installing a single inverter: At least 20 cm (8") t the tp and bttm f the inverter; if installing an inverter with a DC Safety Unit, make sure t leave sufficient clearance fr cable entry. 10 cm (4") t the right and left f the inverter. Fr easy access t the fans (three phase inverters), yu may leave larger clearance. If installing multiple inverters: When installing inverters ne abve the ther, leave at least 40 cm (16") between inverters. If installing an inverter with a DC Safety Unit, leave 20 cm (8") between the tp f an inverter andthe bttm f a DC Safety Unit). When installing inverters side by side, fllw these clearance specificatins: Lcatins where the yearly average Single Phase Inverters high temperature is belw 25 C/77 F 20 cm / 8" Lcatins where the yearly average high temperature is abve 25 C/77 F between inverters Three Phase Inverters 20 cm / 8" between inverters 40 cm / 16" between inverters 21

Munting the Inverter 2. Psitin the munting bracket against the wall/ple and mark the drilling hle lcatins (refer t Mechanical Specificatins n page 96 fr inverter and munting bracket dimensins): Fr Type 1 - Ensure that the U-shaped indentatins are facing up and the UP marking is crrectly riented, as shwn belw: Figure 6: Bracket with U-shaped indentatins facing up Fr Type 2 Ensure that the flat side f the bracket is at the bttm, as in Figure 5. Use at least tw bracket hles. Additinal hles can be used t fix the bracket. Determine which and hw many hles t use accrding t munting surface type and material. 3. Drill the hles and munt the bracket. Verify that the bracket is firmly attached t the munting surface. NOTE When munting an inverter with Type 2 bracket n an uneven surface, yu may use spacers/washers behind the tp munting hle f the bracket (see Figure 7). Depending n the angle, use the apprpriate size and number f spacers s that the bracket is perpendicular t the grund. Recmmended: a stainless steel 3/4" lng screw, with a 1/4" scket buttn head, tw jam nuts and three washers. 22

Chapter 3: Installing the Inverter Figure 7: Munting n uneven surfaces 4. Hang the inverter n the bracket (see Figure 8 and Figure 9): Lift the inverter frm the sides, r hld it at the tp and bttm f the inverter t lift the unit int place. D nt lift hlding the Safety Switch as it may be damaged. Fr Type 1 - Use the screws at the tp f the inverter, as shwn belw. Let the inverter lay flat against the wall r ple. Figure 8: Hanging the inverter n the bracket - Type 1 Fr Type 2 - Align the tw indentatins in the inverter enclsure with the tw triangular munting tabs f the bracket, and lwer the inverter until it rests n the bracket evenly. 23

Munting the Inverter Figure 9: Hanging the inverter n the bracket - Type 2 5. Fr inverters with DC Safety Unit - Optinally, secure the Safety Switch bracket t the wall: Mark the lcatin f the bracket screw fr the Safety Switch and drill the hle. Figure 10: Safety Switch bracket Fasten the bracket using a standard blt. Verify that the bracket is firmly attached t the munting surface. 6. Insert the tw supplied screws thrugh the uter heat sink fin n bth sides f the inverter and int the bracket. Tighten the screws with a trque f 4.0 N*m / 2.9 lb.*ft. Figure 11: Inserting the bracket screws 24

Chapter 4: Cnnecting the AC and the Strings t the Inverter Chapter 4: Cnnecting the AC and the Strings t the Inverter If using an inverter with a DC Safety Unit, refer t the instructins in Cnnecting the AC and DC Strings t the DC Safety Unit n page 103. Refer t Technical Specificatins n page 81 fr specificatins f inverters in different cuntries. Grid Cnnectin Guidelines NOTE Three phase inverters require neutral cnnectin at all times (nly grids with neutral cnnectin are supprted). Fr installatin n a delta grid withut neutral, multiple single phase inverters can be used. Fr mre wiring infrmatin refer t the SlarEdge Recmmended AC Wiring Applicatin Nte, available n the SlarEdge website at http://www.slaredge.cm/files/pdfs/applicatin-nte-recmmended-wiring.pdf When cnnecting multiple single phase inverters in an installatin cnnected t a three-phase grid, phase balancing may be required by the utility r grid peratr. Phase balancing is supprted in the SlarEdge inverters. Fr detailed infrmatin, refer t the SlarEdge Phase Balancing Cnnectin Guide, available n the SlarEdge website at http://www.slaredge.cm/files/pdfs/phase_balancing_cnnectin_guide.pdf. Cnnecting the AC Grid t the Inverter Use a three-wire cable fr a single phase cnnectin r a five-wire cable fr three phase cnnectin. The maximum wire size fr the input terminal blcks is 16mm². 1. Turn OFF the AC circuit breaker. 2. Open the inverter cver: Release the six Allen screws and carefully mve the cver hrizntally befre lwering it. CAUTION! When remving the cver, make sure nt t damage internal cmpnents. SlarEdge will nt be held respnsible fr any cmpnents damaged as a result f incautius cver remval. 25

Cnnecting the AC Grid t the Inverter 3. Strip 58 mm / 2.32'' f the external cable insulatin and strip 8 mm / 0.32'' f the internal wire insulatin. Figure 12: Insulatin stripping AC (3-wire cable) 4. Open the AC cable gland and insert the cable thrugh the gland (see Figure 3). WARNING! Turn OFF the AC befre cnnecting the AC terminals. If cnnecting equipment grunding wire, cnnect it befre cnnecting the AC Line and Neutral wires. 5. Depending n the inverter type (single phase r three phase), cnnect the AC, as fllws. Cnnect the PE (grunding) wire first. Single Phase Inverter Wire type Cnnect t terminal Prtective Earth PE Line L Neutral N Figure 13: Single Phase Inverter AC Terminals 26

Chapter 4: Cnnecting the AC and the Strings t the Inverter Three Phase Inverter Wire type Cnnect t terminal Line 1 L1 Line 2 L2 Line 3 Prtective Earth Neutral L3 (feeds the internal pwer supply) PE N Figure 14: Three Phase Inverter AC Terminals NOTE If pwer cntrl is enabled, it is imprtant t respect the rder f grid lines cnnectin t the inverter. A 120deg phase difference shuld be kept between L1 t L2 and between L2 t L3 (L1-L2-L3 and nt, fr example L1-L3-L2). If the grid lines are nt in this rder, an errr is displayed n the LCD and the inverter will nt prduce pwer. 6. Tighten the screws f each terminal with a trque f 1.2-1.5 N*m / 0.88-1.1 lb*ft. 7. Check that the wires are fully inserted and cannt be pulled ut easily. 8. Tighten the AC cable gland with a trque f 2.8-3.3 N*m / 2.0-2.4 lb*ft. 9. Verify that there are n uncnnected wires t the inverter and that the unused terminal screws are tightened. Cnnecting the Strings t the Inverter Cnnect the string t the DC input pairs. If required, cnnect additinal strings in parallel using an external cmbiner bx/branch cables befre cnnecting t the inverter. NOTE Functinal electrical earthing f DC-side negative r psitive ples is prhibited because the inverter has n transfrmer. Grunding (earth grund) f mdule frames and munting equipment f the PV array mdules is acceptable. NOTE SlarEdge s fixed input vltage architecture enables the parallel strings t be f different lengths. Therefre, they d nt need t have the same number f pwer ptimizers, as lng as the length f each string is within the permitted range. 27

Selecting a Residual Current Device (RCD) Cnnect the DC cnnectrs f each string t the DC+ and DC- cnnectrs accrding t the labels n the inverter. Figure 15: Inverter DC Cnnectins Selecting a Residual Current Device (RCD) IMPORTANT SAFETY FEATURE All SlarEdge inverters incrprate a certified internal Residual Current Device (RCD) in rder t prtect against pssible electrcutin and fire hazard in case f a malfunctin in the PV array, cables r inverter. There are 2 trip threshlds fr the RCD as required fr certificatin (DIN VDE 0126-1-1). The default value fr electrcutin prtectin is 30 ma, and fr slw rising current is 300 ma. If an external RCD is required by lcal regulatins, check which type f RCD is required fr the relevant electric cde. SlarEdge recmmends using a type-a RCD. The recmmended RCD value is 100mA r 300mA unless a lwer value is required by the specific lcal electric cdes. When required by lcal regulatins, the use f an RCD type B is permitted. In installatins where the lcal electric cde requires the use f a lwer leakage RCD, the discharge current f capacitive parasitic leakage may trip the RCD. Use the fllwing prcedure t avid this prblem: l Select an apprpriate RCD t ensure prper peratin f the installatin. A 30mA RCD may still trip at 15mA (accrding t IEC 61008). Gd quality RCDs will trip at a higher value. l PV mdules with lw capacitance leakage t the frame are preferable. Fr detailed infrmatin, refer t the RCD Selectin fr SlarEdge Inverters Applicatin Nte, available n the SlarEdge website at http://www.slaredge.cm/files/pdfs/se-applicatinrcd-selectin.pdf. 28

Chapter 5: Cmmissining the Installatin Chapter 5: Cmmissining the Installatin This chapter describes hw t activate the system, pair the pwer ptimizers t the inverter and verify the prper functining f the system. Step 1: Activating the System 1. Verify that the ON/OFF switch is OFF. 2. Turn ON the AC breaker. 3. Mve the Safety Switch t the ON psitin. 4. Mve the DC Safety Unit (if applicable) t the ON psitin. 5. If nt already remved, remve the inverter cver: Open the inverter cver s six Allen screws and carefully pull the cver hrizntally befre lwering it. WARNING! ELECTRICAL SHOCK HAZARD. D nt tuch uninsulated wires when the inverter cver is remved. 6. Activate the inverter accrding t the activatin instructins supplied in the inverter package: a. Verify card S/N matches inverter S/N. b. Insert the card int slt marked "CARD" n the cmmunicatin bard. c. Turn AC ON. d. LCD shws: Running Script... è Dne! e. If LCD shws: Script errr, cntact SlarEdge Supprt. 7. Verify that the inverter is cnfigured t the prper cuntry: Press the LCD light buttn until reaching the ID status screen: I D : # # # # # # # # # # D S P 1 / 2 : 1. 0 2 1 0 / 1. 0 0 3 4 C P U : 0 0 0 3. 1 4 x x C u n t r y : E S P 8. If required, perfrm the fllwing additinal steps: Cuntry settings r inverter cnfiguratin using the internal LCD user buttns refer t Cuntry and Grid n page 42. Cmmunicatin ptins cnnectin refer t Setting Up Cmmunicatin n page 55. 29

Step 1: Activating the System 9. Clse the inverter cver by tightening the screws with a trque f 9.0 N*m/ 6.6 lb*ft. Fr prper sealing, first tighten the crner screws and then the tw central screws. The fllwing figure illustrates recmmended rder: Figure 16: Tightening rder f the screws 10. Turn ON the DC Safety Unit (if applicable). If an additinal external DC switch is installed between the pwer ptimizers and the inverter(s) then turn it ON. A status screen similar t the fllwing appears n the LCD panel: V a c [ V ] V d c [ V ] P a c [ w ] 2 4 0. 7 1 4. 1 0. 0 P _ O K : 0 0 0 / 0 0 0 < S _ O K > - - - - - - - - - - - - - - - O F F 11. Verify that the fllwing infrmatin appears n the LCD panel: P_OK: Appears nly upn first telemetry receptin frm the pwer ptimizers. Indicates cnnectin t the pwer ptimizers and that at least ne pwer ptimizer is sending mnitring data. If P_OK des nt appear, check the pwer ptimizer, string and DC input cnnectins. 000/000: Appears nly upn first telemetry receptin frm the pwer ptimizers. Indicates the number f pwer ptimizers that have been paired t this inverter. At this stage, the number shuld be 000, since n pwer ptimizers have been paired. S_OK: the cnnectin t the SlarEdge mnitring prtal is successful (shuld appear nly if the inverter is cnnected t the server). If S_OK is nt displayed and the inverter is cnnected t the server, refer t Errrs and Trubleshting n page 66. Vac [V]: the grid AC utput vltage. Verify the crrect value. 30

Chapter 5: Cmmissining the Installatin Vdc [V]: The DC input vltage f the lngest string cnnected t the inverter. There shuld be a safety vltage f 1V fr each pwer ptimizer in the string. NOTE A measurement errr n the inverter LCD f ±3 V is acceptable. Pac [w]: the AC utput pwer (shuld be 0.0 since the inverter is OFF). OFF: the inverter ON/OFF switch is in the OFF psitin. Step 2: Pairing Pwer Optimizers t the Inverter Once all cnnectins are made, all the pwer ptimizers must be lgically paired t their inverter. The pwer ptimizers d nt start prducing pwer until they are paired with an inverter. This step describes hw t assign each inverter t the pwer ptimizers frm which it will prduce pwer. Perfrm this step when the mdules are expsed t sunlight. If the string length is changed r a pwer ptimizer is replaced, repeat the pairing prcess. 1. Press and hld dwn the inverter LCD Light buttn fr abut 10 secnds. The fllwing message is displayed: K e e p h l d i n g b u t t n f r p a i r i n g, r e l e a s e t e n t e r m e n u... R e m a i n i n g : 3 s e c Keep hlding fr 5 secnds until the fllwing is displayed: P a i r i n g T u r n S w i t c h T O n 2. Turn the inverter ON/OFF switch t ON within 5 secnds. If yu wait lnger than 5 secnds the inverter exits the pairing mde. The fllwing message is displayed indicating that the inverter is perfrming the pairing: P a i r i n g R e m a i n i n g [ s e c ] : 1 8 0 31

Step 2: Pairing Pwer Optimizers t the Inverter 3. Wait fr the cmpletin f the pairing (remaining secnds is 0). If pairing fails, an errr is displayed. In this case, repeat the pairing steps, and refer t Pwer Optimizer Trubleshting n page 78. If the prblem persists, cntact SlarEdge Supprt. When pairing succeeds, the fllwing message is displayed: P a i r i n g P a i r i n g C m p l e t e d The system startup prcess begins: Since the inverter is ON, the pwer ptimizers start prducing pwer and the inverter starts cnverting AC. NOTE When yu turn ON the inverter ON/OFF switch, the DC cables carry a high vltage and the pwer ptimizers n lnger utput a safe 1V utput. When the inverter starts cnverting pwer after the initial cnnectin t the AC, the inverter enters Standby mde until its wrking vltage is reached. This mde is indicated by the flickering green inverter LED. While the inverter is in Standby mde, it mnitrs the grid and verifies crrect grid vltage and frequency. The fllwing message is displayed: W a k i n g U p... R e m a i n i n g : 0 5 1 S e c The cuntdwn indicates the secnds remaining until entering the Prductin mde. This time is in accrdance with lcal regulatins and is typically between three t five minutes. When cuntdwn is cmplete, the inverter enters Prductin mde and prduces pwer. The steadily lit green inverter LED indicates this mde. 32

Chapter 5: Cmmissining the Installatin Step 3: Verifying Prper Operatin After the wake-up time is ver, a status screen similar t the fllwing appears n the inverter LCD panel: V a c [ v ] V d c [ v ] P a c [ w ] 2 4 0. 7 3 7 1. 9 2 3 4 9. 3 P _ O K : X X X / Y Y Y < S _ O K >................. O N 1. Verify the fllwing: The green inverter LED is steadily lit. The ON/OFF indicatr n the LCD panel reads ON. P_OK: XXX/YYY: There is a cnnectin t the pwer ptimizers and at least ne pwer ptimizer is sending mnitring data. Optimizers send telemetries in a frequency f up t 10 minutes. Initially after pairing, bth XXX and YYY values shw 000 and the values increase as paired pwer ptimizers are reprted. NOTE It may take up t 20 minutes fr all pwer ptimizers t transmit their telemetries and t be cunted n the LCD screen. S_OK appears, if the inverter is cnnected t the SlarEdge mnitring prtal. Vac [V] specifies the measured grid AC utput vltage. Vdc [v] : Specifies the DC input vltage, which shuld equal the sum f the utput vltages f all mdules (and shuld be within the perating range f the inverter). Pac [W] specifies the ttal AC utput pwer prduced. 2. Take nte f the serial # n the inverter label using the detachable 2D barcde sticker n each device. This infrmatin is used in the SlarEdge mnitring prtal t identify this inverter and is needed t pen a new site in the mnitring prtal. Yur SlarEdge pwer harvesting system is nw peratinal. 33

Step 4: Reprting and Mnitring Installatin Data Step 4: Reprting and Mnitring Installatin Data NOTE This step requires cnnecting ne f the cmmunicatin ptins. Refer t Setting Up Cmmunicatin n page 55. The SlarEdge Mnitring System The SlarEdge mnitring prtal enables accessing SlarEdge site infrmatin, including upt-date infrmatin viewed in a physical r lgical view.the mnitring prtal is described in detail in the SlarEdge Mnitring Prtal User Guide, available n the SlarEdge website at http://www.slaredge.cm/files/pdfs/slaredge-mnitring-prtal-user-guide.pdf. The SlarEdge mnitring prtal can display lgical and physical layuts f the installed system, as fllws: Lgical Layut: Shws a schematic lgical layut f the cmpnents in the system, such as: inverters, strings and mdules, as well as their electrical cnnectivity. This view enables yu t see which mdules are cnnected in each string, which strings are cnnected t each inverter, and s n. Physical Layut: Shws a schematic physical layut f the cmpnents in the system, such as: inverters, strings and mdules, as well as their electrical cnnectivity. This view enables a bird s eye view f the actual lcatin f a system cmpnent. Using the prtal, yu can: View the latest perfrmance f specific cmpnents. Find under-perfrming cmpnents, such as mdules, by cmparing their perfrmance t that f ther cmpnents f the same type. Pinpint the lcatin f alerted cmpnents using the physical layut. See hw cmpnents are cnnected t each ther. Pair pwer ptimizers remtely. T display a lgical layut, insert the inverter serial number in the new site created in the applicatin. When the cmmunicatin between the inverter and the mnitring server is established, the lgical layut is displayed. T display a physical layut, yu need t map the lcatins f the installed pwer ptimizers. T generate a physical mapping, use either the Site Mapper applicatin r a mapping template, which shuld be filled ut using the detachable stickers (see Prviding Installatin Infrmatin, belw). The lgical and physical mapping can be used fr debugging a prblem using the SlarEdge mnitring prtal. 34

Chapter 5: Cmmissining the Installatin If yu d nt reprt the physical and lgical mapping f the installed pwer ptimizers t SlarEdge, the SlarEdge mnitring prtal will shw the lgical layut indicating which pwer ptimizers are cnnected t which inverter, but will nt shw strings r the physical lcatin f pwer ptimizers. The inverter may be cnnected t the SlarEdge mnitring prtal via LAN r via an external mdem cnnected t the inverter's RS232 cnnectr. Alternatively, yu can cnnect the inverter t anther inverter that is already cnnected t the server, in a master-slave cnfiguratin. Refer t Setting Up Cmmunicatin n page 55. Prviding Installatin Infrmatin Paper Template Fill ut the Physical Layut Template (dwnladable frm the SlarEdge site) using the detachable 2D barcde stickers n each pwer ptimizer. Once the frm is cmpleted, scan it and uplad the scanned file t the SlarEdge mnitring prtal during site registratin. Fr an example paper template, refer t http://www.slaredge.cm/files/pdfs/physical-layuttemplate.pdf. Site Mapper Use the SlarEdge Site Mapper smartphne applicatin t scan the pwer ptimizer and inverter 2D barcdes. The applicatin creates an XML file that can be upladed t the SlarEdge mnitring prtal during site registratin. The SlarEdge Site Mapper can be dwnladed frm the applicatin stres. Fr detailed infrmatin, refer t the SlarEdge Site Mapper Sftware Guide r t the Site Mapper dem mvie, available n the SlarEdge website at http://www.slaredge.cm/grups/installer-tls/site-mapper. Creating a Site in the SlarEdge Mnitring Prtal Create the site in the mnitring prtal using the registratin frm available at http://www.slaredge.cm/grups/site-registratin. Fill ut all required infrmatin in the frm, which includes infrmatin abut yur installatin, as well as details abut its lgical and physical mapping. 35

Chapter 6: User Interface Chapter 6: User Interface LCD User Buttns Fur buttns are lcated inside the inverter abve the LCD panel and are used fr cntrlling the LCD menus, as shwn belw: Figure 17: LCD Internal menu buttns Use the fur user buttns t cntrl the LCD panel menus: Esc: Mves the cursr (>) t the beginning f the currently displayed parameter; ges t the previus menu, and cancels a value change with a lng press (until Abrted is displayed). Up (1) and Dwn (2): Mves the cursr frm ne menu ptin t anther, mves amng the characters f a displayed parameter, and tggles between pssible characters when setting a value. Enter (3):Selects a menu ptin and accepts a value change with a lng press (until Applied is displayed). Use the three rightmst buttns fr entering 123 when entering the Setup mde passwrd 12312312. The LCD screen displays status infrmatin f the system and varius menus fr cnfiguratin ptins. The LCD panel and buttns are used during the fllwing prcesses: Operatinal mde: The LCD panel allws checking fr prper system peratin. Refer t Status Screens - Operatinal Mde n page 48 fr a descriptin f this ptin. Use the LCD light buttn t tggle thrugh the infrmative displays. Setup mde: Upn installatin, the installer may perfrm basic cnfiguratin, as described in Inverter Cnfiguratin Setup Mde n the facing page. 36

Chapter 6: User Interface Errr messages: In the event f a prblem, an errr message may be displayed n the LCD panel. Fr mre infrmatin, refer t Errrs and Trubleshting n page 66 and Inverter Cnfiguratin Setup Mde belw Inverter Cnfiguratin Setup Mde Yu can cnfigure the inverter using ne f the fllwing: The internal LCD user buttns. When using this ptin, the inverter cver is remved. The external LCD light buttn. When using this ptin, remving the inverter cver is nt required. This ptin f cnfiguratin includes a less detailed cnfiguratin menu. Cnfiguring the Inverter Using the Internal LCD User Buttns After inverter installatin, a field technician may perfrm basic system cnfiguratin. Cnfiguratin is dne when the inverter is in Setup mde. T enter Setup mde: 1. Turn the inverter ON/OFF switch t OFF (AC remains ON). WARNING! If the inverter was perating prperly (pwer was prduced by the pwer ptimizers), the fllwing message is displayed. D C V O L T A G E N O T S A F E D O N O T D I S C O N N E C T V D C : 7 2. 0 This message is displayed until the DC vltage is safe (50V). D nt pen the cver until the vltage is safe r until at least five minutes have passed. 2. Press the Enter buttn fr at least 5 secnds. The fllwing message is displayed: P l e a s e e n t e r P a s s w r d * * * * * * * * 3. Use the three rightmst internal LCD user buttns t type in the fllwing passwrd: 12312312. The fllwing message is displayed: C u n t r y < I t a l y > L a n g u a g e < E n g > C m m u n i c a t i n P w e r C n t r l D i s p l a y M a i n t e n a n c e I n f r m a t i n 37

Cnfiguring the Inverter Using the Internal LCD User Buttns The inverter is nw in Setup mde and all its LEDs are lit. The inverter autmatically exits Setup mde if n buttns are pressed fr mre than 2 minutes. The fllwing shws a hierarchical tree f the menu ptins, which are described in Cnfiguratin Menu Optins n page 42. Actual menus may vary frm shwn depending n the firmware versin f the inverter. Main menu: Cuntry: Language: C u n t r y < I t a l y > L a n g u a g e < E n g > C m m u n i c a t i n P w e r C n t r l D i s p l a y M a i n t e n a n c e I n f r m a t i n G e r m a n y + S p a i n F r a n c e... E n g l i s h G e r m a n S p a n i s h F r e n c h I t a l i a n Cmmunicatin 1 S e r v e r < L A N > L A N C n f R S 4 8 5 1 C n f < S > Z i g B e e C n f < S > W i - F i C n f < N / A > R S 2 3 2 C n f G P I O C n f < M T R > 1 If ZigBee is cnnected, the Wi-Fi Cnf menu is nt displayed. If ZigBee is nt cnnected, ZigBee Cnf and Wi-Fi Cnf are bth displayed with <N/A>. 38

Chapter 6: User Interface Pwer Cntrl 1 : Display: Maintenance: Infrmatin: G r i d C n t r l < E n > E n e r g y M a n a g e r R R C R C n f. R e a c t i v e P w r C n f. A c t i v e P w r C n f. W a k e u p C n f. P h a s e B a l a n c e < D i s > P ( f ) A d v a n c e d L a d D e f a u l t s T e m p e r a t u r e < C > L C D O n T i m e < 3 0 > T L M O n T i m e < 1 5 > D a t e a n d T i m e R e s e t C u n t e r s F a c t r y R e s e t S W U p g r a d e S D - C a r d D i a g n s t i c s S t a n d b y M d e G r i d P r t e c t i n V e r s i n s E r r r L g W a r n i n g l g H a r d w a r e I D s Cnfiguring the Inverter Using the LCD Light Buttn Use the LCD light buttn fr cmmunicatin setup and fr displaying the Errr lg and Warning Lg withut having t pen the Inverter cver. There are fewer menus available when using this cnfiguratin ptin; hwever, the functinality f these menus is the same as when using the internal LCD user buttns. 1 Phase Balance is applicable t single phase inverters nly. 39

Cnfiguring the Inverter Using the LCD Light Buttn 1. Turn the inverter ON/OFF switch t OFF. 2. Press and hld dwn the LCD light buttn until the fllwing message is displayed: K e e p h l d i n g b u t t n f r p a i r i n g, r e l e a s e t e n t e r m e n u... R e m a i n i n g : 3 s e c Releasing the buttn displays the fllwing menu: O p t i m i z e r p a i r i n g L a n g u a g e < e n g > C m m u n i c a t i n M a i n t e n a n c e I n f r m a t i n E x i t 3. Shrt-press (ne secnd) t scrll dwn t the next menu ptin, and lng-press (three secnds) t select the item. Yu can use the Exit ptin in these menus t mve up ne menu level r t exit the Setup mde frm the main menu. 40

Chapter 6: User Interface The fllwing shws a hierarchical tree f the menu ptins that appear when using the LCD light buttn: Main menu: Language: O p t i m i z e r p a i r i n g L a n g u a g e < e n g > C m m u n i c a t i n M a i n t e n a n c e I n f r m a t i n E x i t E n g l i s h G e r m a n S p a n i s h F r e n c h I t a l i a n E x i t Cmmunicatin 1 : Infrmatin: S e r v e r < L A N > L A N C n f R S 4 8 5 1 C n f < S > Z i g B e e C n f < S > W i - F i C n f < N / A > G P I O C n f < M T R > R S 2 3 2 C n f E x i t V e r s i n s E r r r L g W a r n i n g l g H W I D s E x i t 1 If Wi-Fi is cnnected, the ZigBee Cnf menu is nt displayed, and vice versa. 41

Cnfiguratin Menu Optins Maintenance: D a t e a n d T i m e R e s e t C u n t e r s F a c t r y R e s e t S W U p g r a d e S D - C a r d D i a g n s t i c s S t a n d b y M d e G r i d P r t e c t i n E x i t The ptins presented in these menus are described in the next sectin. Cnfiguratin Menu Optins This sectin describes hw t use the LCD menus fr cnfiguring the inverter. Cnfiguratin is nly available when the inverter ON/OFF switch is OFF. Use either the internal LCD user buttns r the external LCD light buttn t mve between and select menu ptins. Cuntry and Grid Cnfiguring the cuntry and grid is available using the internal user buttns nly. 1. Select the Cuntry ptin t specify the cuntry in which the inverter is installed and the grid t which it is cnnected. This parameter may arrive pre-cnfigured. If s, verify that it is set t the prper cuntry. WARNING! The inverter must be cnfigured t the prper cuntry in rder t ensure that it cmplies with the cuntry grid cde and functins prperly with that cuntry grids. A list f cuntries is displayed. If n cuntry is cnfigured, the value is <NONE>. NOTE If an inverter is nt cnfigured t any cuntry, it will nt prduce energy, and the fllwing message will be displayed n the LCD: N Cuntry Selected A plus sign (+) near the cuntry indicates that anther menu will be displayed after selectin. 2. Cnfirm yur cuntry selectin in the cnfirmatin screen: Tggle t YES and press Enter. Language 1. Select the Language ptin t set the language in which the LCD shuld display. 2. Cnfirm yur language selectin in the cnfirmatin screen: Tggle t YES and press Enter. 42

Chapter 6: User Interface Cmmunicatin 1. Select the Cmmunicatin ptin t define and cnfigure: The cmmunicatin ptin used by the inverter t cmmunicate with the SlarEdge mnitring prtal The cmmunicatin ptin used t cmmunicate between multiple SlarEdge devices r ther external nn-slaredge devices, such as electricity meters r lggers. 2. Select Server t set which cmmunicatin methd is used t cmmunicate between devices and the SlarEdge mnitring prtal. Refer t Setting Up Cmmunicatin n page 55 fr a full descriptin f these cmmunicatin ptins. NOTE The Server menu shws nly the cmmunicatin ptins installed in the inverter. The fllwing shws a hierarchical tree f the menu ptins in the Cmmunicatin menu. Fr detailed infrmatin abut all the cnfiguratin ptins, refer t the Cmmunicatin Optins Applicatin Nte, available n the SlarEdge website at http://www.slaredge.cm/files/pdfs/slaredge-cmmunicatin_ptins_applicatin_nte_ v2_250_and_abve.pdf.. Cmmunicatin 1 : S e r v e r < L A N > L A N C n f R S 4 8 5 1 C n f < S > Z i g B e e C n f < S > W i - F i C n f < N / A > R S 2 3 2 C n f G P I O C n f < M T R > Server: L A N R S 4 8 5 Z i g b e e W i - F i R S 2 3 2 N n e 1 If ZigBee is cnnected, the Wi-Fi Cnf menu is nt displayed. If ZigBee is nt cnnected, ZigBee Cnf and Wi-Fi Cnf are bth displayed with <N/A> and their menus are nt accessible. 43

Cmmunicatin LAN Cnf: RS485-1 Cnf: I P C n f i g S e t D H C P < e n > S e t I P S e t M a s k S e t G a t e w a y S e t D N S S e t S e r v e r A d d r S e t S e r v e r P r t D e v i c e T y p e < S E > P r t c l < M > D e v i c e I D < 1 > S l a v e D e t e c t < # > S l a v e L i s t < # > ZigBee Cnf. (enabled nly if the ZigBee internal mdule is cnnected): D e v i c e T y p e < S E > P r t c l < M P > D e v i c e I D < 1 > P A N I D S c a n C h a n n e l L a d Z B D e f a u l t s P r f i l e < Z B 2 0 0 7 > Wi-Fi Cnf (enabled nly if the internal mdule is cnnected): RS232 Cnf: GPIO Cnf: S c a n N e t w r k s S e t k e y L a d D e f a u l t s D e v i c e T y p e < S E > P r t c l < G S M > S e t A P N S e t M d e m T y p e S e t U s e r N a m e S e t P a s s w r d D e v i c e T y p e < R R C R > 44

Chapter 6: User Interface Pwer Cntrl Fr detailed infrmatin abut active and reactive pwer cntrl ptins refer t the Pwer Cntrl Applicatin Nte, available n the SlarEdge website at http://www.slaredge.cm/files/pdfs/applicatin_nte_pwer_cntrl_cnfiguratin.pdf. G r i d C n t r l < E n > E n e r g y M a n a g e r R R C R C n f. R e a c t i v e P w r C n f. A c t i v e P w r C n f. W a k e u p C n f. P h a s e B a l a n c e < D i s > P ( f ) A d v a n c e d L a d D e f a u l t s NOTE Phase Balance is applicable t single phase inverters nly. Fr detailed infrmatin, refer t the SlarEdge Phase Balancing Manual, available n the SlarEdge website at http://www.slaredge.cm/files/pdfs/phase_balancing_cnnectin_guide.pdf The Grid Cntrl ptin is disabled by default. Enabling it pens additinal ptins in the menu, as shwn n page 38. Display Select Display t set the fllwing: T e m p e r a t u r e < C > L C D O n T i m e < 3 0 > T L M O n T i m e < 1 5 > Temperature: Select Celsius r Fahrenheit units. LCD On Time <30>: The number f secnds that the LCD backlight is ON after pressing the LCD light buttn. Set a value within the range f 10-120 secnds. TLM On Time <15>: The number f minutes that the LCD backlight is ON while viewing the Telemetry windw. Set a value within the range f 1-120 minutes. 45

Maintenance Maintenance Select Maintenance t set the fllwing ptins: D a t e a n d T i m e R e s e t C u n t e r s F a c t r y R e s e t S W U p g r a d e S D - C a r d D i a g n s t i c s S t a n d b y M d e G r i d P r t e c t i n Date and Time: Set the internal real-time clck. If cnnected t the SlarEdge mnitring prtal, the date and time are set autmatically and nly time zne shuld be set. Reset Cunters: Resets the accumulated energy cunters that are sent t the SlarEdge mnitring prtal Factry Reset: Perfrms a general reset t the default device settings. SW Upgrade SD-Card: Perfrm a sftware upgrade using an SD card. Diagnstics: Displays the Islatin Status screen. Refer t http://www.slaredge.us/files/pdfs/applicatin_nte_islatin_fault_ trubleshting.pdf. Standby Mde: Enables/disables Standby Mde - fr remte cmmissining. Grid Prtectin: Available in specific cuntries. Enables viewing and setting grid prtectin values. Refer t http://www.slaredge.cm/files/pdfs/viewing_grid_ prtectin_values.pdf. Infrmatin Select Infrmatin t display the fllwing ptins: V e r s i n s E r r r L g W a r n i n g l g H a r d w a r e I D s Versins: Displays inverter firmware versins: ID: The inverter ID. DSP 1/2: The DSP digital cntrl bard firmware versin CPU: The cmmunicatin bard firmware versin NOTE Please have these numbers ready when yu cntact SlarEdge Supprt. 46

Chapter 6: User Interface Errr Lg: Displays the last five errrs. Warning Lg: Displays the last five warnings. Hardware IDs: Displays the fllwing HW serial numbers (if exist, and cnnected t the inverter): ID: the inverter's ID RGM1: electricity meter (with lwer Mdbus ID) RGM2: A secnd external electricity meter (with the higher Mdbus ID) ZB: Zigbee MAC address Cell: MEID (CDMA) r IMEI (GSM) WiFi: Wi-Fi MAC address 47

Status Screens - Operatinal Mde Status Screens - Operatinal Mde During nrmal peratin pressing the external LCD light buttn turns n the LCD backlight. Additinal presses display the fllwing screens ne after the ther. Initial Status V a c [ V ] V d c [ V ] P a c [ W ] 2 4 0. 7 3 7 1. 9 2 3 4 9. 3 P _ O K : X X X / Y Y Y < S _ O K > - - - - - - - - - - - - - - - - O N Vac [V]: The AC utput vltage Vdc [V]: The DC input vltage Pac [W]: The AC utput pwer P_OK: XXX/YYY: There is a cnnectin t the pwer ptimizers and at least ne pwer ptimizer is sending mnitring data. XXX is the number f pwer ptimizers fr which telemetries have been received in the last tw hurs. YYY is the number f paired pwer ptimizers identified during the mst recent pairing prcess. If XXX and YYY are nt equal, there may be a prblem in ne r mre pwer ptimizers. S_OK: The cnnectin t the SlarEdge mnitring prtal is successful (appears nly if the inverter is cnnected t the server). ON/OFF: Indicates the psitin f the inverter ON/OFF switch. Main Inverter Status V a c [ V ] V d c [ V ] P a c [ W ] 2 4 0. 7 3 7 1. 9 3 2 1 0. 0 F a c [ H z ] O P s _ O k T e m p 5 0. 0 1 1 2 8. 2 Vac [V: The AC utput vltage. Vdc [V]: The DC input vltage. Pac [W]: The AC utput pwer. Fac [Hz]: The AC utput frequency. OPs_Ok: Number f ptimizers sending telemetries (indicating that they are paired) Temp [C r F]: The inverter heat sink temperature 48

Chapter 6: User Interface Energy Meter Status Displays the ttal energy prduced during the last day, mnth, year and since inverter installatin. D a y [ W h ] : 0. 0 M n t h [ K W h ] : 0. 0 Y e a r [ K W h ] : 0. 0 T t a l [ K W h ] : 0. 0 If an electricity meter meter is cnnected t the inverter, the fllwing status screen, shwing the ttal energy reading, is displayed instead f the abve screen: R e v e n u e G r a d e M e t e r S t a t u s : < O K > < E r r r M e s s a g e > T t a l [ W h ] : X X X X X X X Status: Displays OK if the meter is cmmunicating with the cmmunicatin bard. <Errr message>: If an internal meter errr is displayed here, cntact SlarEdge Supprt. Ttal (Wh): The energy read by the meter. The value displayed in this line depends n the meter type cnnected t the inverter and its lcatin: If a bidirectinal meter is cnnected at the cnsumptin pint, this value is the cnsumed energy. If the meter is installed at the prductin cnnectin pint, this value is the energy prduced by the site. If the meter is installed at the grid cnnectin pint, this value is the energy fed int the grid. If the inverter is cnnected t the SlarEdge server, this value will als be displayed in the mnitring prtal. NOTE This data is accumulated accrding t an internal real-time clck. 49

Telemetry Status Telemetry Status This windw displays the last pwer ptimizer telemetry received. The display changes as each pwer ptimizer sends its telemetry. In rder t verify prper installatin, the installer may view the Telemetry windw fr sme time in rder t bserve the pwer ptimizers' reprt prcess. M d u l e : 0 0 0 C 1 E D 9-0 3 E n e r g y [ W h ] : 0 V d c _ O [ V ] : 4 0. 5 V d c _ I [ V ] : 2 9. 5 Mdule#: Pwer ptimizer serial number Energy: pwer ptimizer energy Vdc_O: Pwer ptimizer utput vltage Vdc_I: Pwer ptimizer input vltage (mdule vltage) ID Status This windw displays the inverter sftware versin and the cuntry t which the inverter is cnfigured. I D : # # # # # # # # # # D S P 1 / 2 : 1. 0 2 1 0 / 1. 0 0 3 4 C P U : 0 0 0 3. 1 4 x x C u n t r y : E S P ID: The inverter ID. DSP 1/2: The DSP digital cntrl bard firmware versin CPU: The cmmunicatin bard firmware versin Cuntry: the current cuntry setting Server Cmmunicatin Status S e r v e r : L A N < S _ O K > S t a t u s : < O K > x x x x x x x x < E R R O R M E S S A G E > Server: The methd f cnnectin t the SlarEdge mnitring prtal. S_OK: The cnnectin t the SlarEdge mnitring prtal is successful (shuld appear nly if the inverter is cnnected t the server). 50

Chapter 6: User Interface Status: Displays OK if the inverterestablished successful cnnectin and cmmunicatin with the specified server prt/device (LAN, RS485, Wi-Fi r ZigBee mdule). xxxxxxxx: Eight-bit Ethernet cmmunicatin cnnectin status: A string f 1s and 0s is displayed. 1 indicates OK, 0 indicates an errr. Fr a list f the pssible errrs and hw t trublesht them, refer t Trubleshting Cmmunicatin - S_OK is Nt Displayed n page 66. Errr message, accrding t failure. Refer t Errrs and Trubleshting n page 66. IP Status This windw describes the Ethernet cnfiguratin: IP, Mask, Gateway and MAC address (Media Access Cntrl) f the Inverter. I P 1 9 2. 1 6 8. 2. 1 1 9 M S K 2 5 5. 2 5 5. 2 5 5. 0 G W 1 9 2. 1 6 8. 2. 1 M A C 0-2 7-0 2-0 0-3 9-3 6 ZigBee Status This windw describes the ZigBee cnfiguratin: P A N : X X X X X C H : X X / X X X X R S S I : < L > M I D : X X X X X X RSSI: The receive signal strength indicatin f the clsest ZigBee in the system. L = lw, M = medium, H = high and (-) = n signal. PAN ID: The ZigBee transceiver PAN ID Ch.: The ZigBee transceiver channel ID: The ZigBee transceiver ID MID: The Master ID f the crdinatr (master) ZigBee mdule. This field is shwn nly in devices with ruter (slave) ZigBee mdules, and after a successful ZigBee assciatin. If a ZigBee mdule is nt cnnected, a N ZigBee message is displayed instead f the MID field. Wi-Fi Status This windw describes the Wi-Fi cnfiguratin: I P : 1 9 2. 1 6 8. 2. 1 1 9 G W : 1 9 2. 1 6 8. 2. 1 S S I D : x x x x x x x x R S S I : < L / M / H / - > 51

Cmmunicatin Prts Status IP: The DHCP prvided address GW: The gateway IP address SSID: Service Set Identifier - the name f a wireless lcal area netwrk (WLAN). All wireless devices n a WLAN must emply the same SSID in rder t cmmunicate with each ther. RSSI: The receive signal strength indicatin f the clsest Wi-Fi in the SlarEdge system. L = lw, M = medium, H = high and - = n signal. Cmmunicatin Prts Status D e v P r t # # R S 4 8 5-1 < S E > < S > < - - > Z i g B e e < S E > < M P S > < - - > ##: The ttal number f slaves detected n the specific prt Dev: The type f device that was cnfigured t a specific prt (based n the prt s functinality), as fllws: SE: SlarEdge device (default) DM: Revenue meter LGR: Nn-SlarEdge lgger PROT: The prtcl type t which the prt is set: Fan Status Fr a SlarEdge device: S: SlarEdge slave M: SlarEdge master P2P: ZigBee pint-t-pint MPM: ZigBee multipint master (fr the SlarEdge ZigBee hme gateway) MPS: ZigBee multipint slave (fr a ZigBee ruter mdule) Fr electricity meters, refer t the applicatin nte - Cnnecting an Electricity Meter t SlarEdge Devices at http://www.slaredge.cm/files/pdfs/cnnecting-revenue-grade-meter-tslaredge-devices.pdf. SS: SunSpec - fr a nn-slaredge lgger This windw is applicable t Three Phase Inverters inverters and prvides infrmatin abut the status f the inverter external and internal fans: 52

Chapter 6: User Interface F a n S t a t u s : F a n 1 : N t W r k i n g F a n 2 : O p e r a t i n g r F a n S t a t u s : I n t : N t W r k i n g E x t : O p e r a t i n g Each fan can have ne f the fllwing statuses: Operating: Fan OK Nt Wrking: This status may indicate a system errr and nt necessarily a faulty fan. Turning AC OFF and ON again may clear this status. If the status des nt change, replace the fan. Fr mre infrmatin, refer t External Fan Maintenance and Replacement n page 109. 53

Pwer Cntrl Status Pwer Cntrl Status Available frm cmmunicatin bard (CPU) firmware versin 2.7xx/3.7xx and later. P W R C T R L : R E M O T E P W R L i m i t : 1 0. 0 4 k W C s P h i : 0. 9 P w e r P r d : 7 0 0 0 W PWR CTRL: The pwer cntrl status: REMOTE - Cmmunicatin with the RRCR r smart energy manager is cnfirmed/validated. LOCAL - The pwer is cntrlled lcally (e.g. by a fixed limit), r this inverter limits the PV pwer prductin t its relative prtin f the feed-in pwer limit, as a result f discnnected cmmunicatin with the smart energy manager. If this status appears, check the cmmunicatin t the smart energy manager r the cmmunicatin t the meter. PWR Limit: The inverter maximum utput pwer set by ne f the pwer limiting ptins: RRCR Smart energy manager (Feed-in limitatin) P(f) Q(U) Cs Phi: The rati between active t reactive pwer Pwer Prd: The pwer prduced by the inverter Fr mre infrmatin, refer t the fllwing applicatin ntes: Pwer Cntrl Applicatin Nte, available n the SlarEdge website at http://www.slaredge.cm/files/pdfs/applicatin_nte_pwer_cntrl_ cnfiguratin.pdf Feed-in Limitatin Applicatin Nte, available n the SlarEdge website at http://www.slaredge.cm/files/pdfs/prducts/feed-in_limitatin_applicatin_ nte.pdf 54

Chapter 7: Setting Up Cmmunicatin Chapter 7: Setting Up Cmmunicatin Pwer ptimizers send infrmatin t the inverter via the DC pwer lines (the PV utput circuit). The infrmatin is sent frm the inverter t the SlarEdge mnitring prtal thrugh the Internet. In rder t send the data frm the inverter, a cmmunicatin cnnectin must be set up, as described in this chapter. Cmmunicatin setup is nt required fr pwer harvesting, hwever is needed fr using the SlarEdge mnitring prtal. This chapter describes setting up cmmunicatin between multiple inverterss fr a master/slave cnfiguratin. CAUTION! When cnnecting the cmmunicatin cables, make sure that the ON/OFF switch at the bttm f the inverter is turned OFF, and the AC is turned OFF. When cnfiguring the cmmunicatin parameters, make sure that the ON/OFF switch is OFF, and the AC is turned ON. Cmmunicatin Types Ethernet: used fr a LAN cnnectin RS485: used fr the cnnectin f multiple SlarEdge devices n the same bus in a master-slave cnfiguratin. RS485 type can als be used as an interface t external nn-slaredge devices, such as revenue meters and data lggers. ZigBee: Optinal wireless cmmunicatin (purchased separately; refer t the supplied manual). Wi-Fi: Optinal wireless cnnectin (purchased separately; refer t the supplied manual). Only cmmunicatin prducts ffered by SlarEdge are supprted. Always cnnect the cmmunicatin ptins when the inverter is OFF. Cmmunicatin Cnnectrs Tw cmmunicatin glands are used fr cnnectin f the varius cmmunicatin ptins. Each gland has three penings. The table belw describes the functinality f each pening. Unused penings shuld remain sealed. 1 (PG16) Gland# Opening Functinality Cable Size (diameter) One small External antenna cable 2-4 mm Tw large Ethernet cnnectin (CAT5/6), ZigBee, r Wi-Fi 4.5-7 mm 2 (PG13.5) All three RS485, pwer reductin 2.5-5 mm 55

Remving the Inverter Cver Figure 18: Cmmunicatin Glands The cmmunicatin bard has a standard RJ45 terminal blck fr Ethernet cnnectin, a 9-pin terminal blck fr RS485 cnnectin, as shwn belw: Figure 19: Internal cnnectrs Remving the Inverter Cver Use the fllwing prcedure fr cver remval fr cmmunicatin cnnectin purpses. 1. Turn the inverter ON/OFF switch t OFF. 2. Discnnect the AC t the inverter by turning OFF the circuit breakers n the distributin panel. Wait 5 minutes fr the capacitrs t discharge. 3. Open the inverter cver s six Allen screws and carefully pull the cver hrizntally befre lwering it. CAUTION! When remving the cver, make sure nt t damage internal cmpnents. SlarEdge will nt be held respnsible fr any cmpnents damaged as a result f incautius cver remval. 56

Chapter 7: Setting Up Cmmunicatin Creating an Ethernet (LAN) Cnnectin This cmmunicatin ptin enables using an Ethernet cnnectin t cnnect the inverter t the mnitring prtal thrugh a LAN. Ethernet cable specificatins: Cable type CAT5/CAT6 Maximum distance between the inverter and the ruter 100 m/ 330 ft. NOTE If using a cable lnger than 10 m/33 ft in areas where there is a risk f induced vltage surges by lightning, it is recmmend t use external surge prtectin devices. Fr details refer t: http://www.slaredge.cm/files/pdfs/lightning_surge_prtectin.pdf. If grunded metal cnduit are used fr ruting the cmmunicatin wires, there is n need fr a lightning prtectin device. Figure 20: Example f Ethernet cnnectin T cnnect the Ethernet cable: 1. Remve the inverter cver as described in. 2. Open the cmmunicatin gland #1. CAUTION! The gland includes a rubber waterprf fitting, which shuld be used t ensure prper sealing. 3. Remve the plastic seal frm the large pening that has a cut in the rubber fitting. 57

Creating an Ethernet (LAN) Cnnectin 4. Remve the rubber fitting frm the gland and insert the CAT5/6 cable thrugh the gland and thrugh the gland pening in the inverter. 5. Push the cable int the cut pening f the rubber fitting. Figure 21: Cable glands and rubber fitting CAT5/6 standard cables have eight wires (fur twisted pairs), as shwn in the diagram belw. Wire clrs may differ frm ne cable t anther. Yu can use either wiring standard, as lng as bth sides f the cable have the same pin-ut and clr-cding. RJ45 Pin # T568B Wire Clr 1 T568A 10Base-T Signal 100Base-TX Signal 1 White/Orange White/Green Transmit+ 2 Orange Green Transmit- 3 White/Green White/Orange Receive+ 4 Blue Blue Reserved 5 White/Blue White/Blue Reserved 6 Green Orange Received- 7 White/Brwn White/Brwn Reserved 8 Brwn Brwn Reserved Figure 22: Standard cable wiring 1 The inverter cnnectin des nt supprt RX/TX plarity change. Supprting crssver Ethernet cables depends n the switch capabilities. 58

Chapter 7: Setting Up Cmmunicatin 6. Use a pre-crimped cable t cnnect via gland #1 t the RJ45 plug n the inverter's cmmunicatin bard r, if using a spl f cable, cnnect as fllws: a. Insert the cable thrugh gland #1. b. Remve the cable s external insulatin using a crimping tl r cable cutter and expse eight wires. c. Insert the eight wires int an RJ45 cnnectr, as described in Figure 22 d. Use a crimping tl t crimp the cnnectr. e. Cnnect the Ethernet cnnectr t the RJ45 prt n the cmmunicatin bard. Figure 23: The RJ45 Ethernet cnnectin 7. Fr the switch/ruter side, use a pre-crimped cable r use a crimper t prepare an RJ45 cmmunicatin cnnectr: Insert the eight wires int the RJ45 cnnectr in the same rder as abve (Figure 22). 8. Cnnect the cable RJ45 cnnectr t the RJ45 prt f the Ethernet switch r ruter. Yu can cnnect mre than ne inverter t the same switch/ruter r t different switches/ruters, as needed. Each inverter sends its mnitred data independently t the SlarEdge mnitring prtal. 59

Creating an RS485 Bus Cnnectin 9. The inverter is cnfigured by default t LAN. If recnfiguratin is required: a. Make sure the ON/OFF switch is OFF. b. Turn ON the AC t the inverter by turning ON the circuit breaker n the main distributin panel. c. Use the internal user buttns t cnfigure the cnnectin, as described in Cmmunicatin n page 43. NOTE If yur netwrk has a firewall, yu may need t cnfigure it t enable the cnnectin t the fllwing address: Destinatin Address: prd.slaredge.cm TCP Prt: 22222 (fr incming and utging data) 10. Verify the cnnectin, as described in Verifying the Cnnectin n page 65. Creating an RS485 Bus Cnnectin The RS485 ptin enables creating a bus f cnnected inverters, cnsisting f up t 31 slave inverters and 1 master inverter. Using this ptin, inverters are cnnected t each ther in a bus (chain), via their RS485 cnnectrs. The first and last inverters in the chain must be terminated. RS485 wiring specificatins: Cable type: Min. 3-wire shielded twisted pair (a 4-wire cable may be used) Wire crss-sectin area: 0.2-1 mm²/ 24-18 AWG (a CAT5 cable may be used) Maximum ndes: 32 Maximum distance between first and last devices: 1 km /3300 ft. NOTE If using a cable lnger than 10 m/33 ft in areas where there is a risk f induced vltage surges by lightning, it is recmmend t use external surge prtectin devices. Fr details refer t: http://www.slaredge.cm/files/pdfs/lightning_surge_prtectin.pdf. If grunded metal cnduit are used fr ruting the cmmunicatin wires, there is n need fr a lightning prtectin device. NOTE If an electricity meter is cnnected t yur inverter, it uses the RS485 prt and therefre an RS485 cmmunicatin bus cannt be created. The fllwing sectins describe hw t physically cnnect the RS485 bus and hw t cnfigure the bus. 60

Chapter 7: Setting Up Cmmunicatin T cnnect the RS485 cmmunicatin bus: 1. Remve the inverter cver as described in Remving the Inverter Cver n page 56. 2. Remve the seal frm ne f the penings in cmmunicatin gland #2 and insert the wire thrugh the pening. 3. Pull ut the 9-pin RS485/RS232 terminal blck cnnectr, as shwn belw: Figure 24: The RS485 terminal blck 4. Lsen the screws f pins A(+), B(-), and G n the left f the RS485 terminal blck. Figure 25: RS485/RS232 terminal blck 5. Insert the wire ends int the G, A and B pins shwn abve. Use Fur- r six-wire twisted pair cable fr this cnnectin. Yu can use any clr wire fr each f the A, B and G cnnectins, as lng as the same clr wire is used fr all A pins, the same clr fr all B pins and the same clr fr all G pins. 61

Creating an RS485 Bus Cnnectin 6. Fr creating an RS485 bus - cnnect all B, A and G pins in all inverters. The fllwing figure shws this cnnectin schema: NOTE Figure 26: Cnnecting the inverters in a chain D nt crss-cnnect B, A and G wires. D nt insert wires int RS485-2 pins. 7. Tighten the terminal blck screws. 8. Check that the wires are fully inserted and cannt be pulled ut easily. 9. Push the RS485 terminal blck firmly all the way int the cnnectr n the right side f the cmmunicatin bard. 62

Chapter 7: Setting Up Cmmunicatin 10. Terminate the first and last SlarEdge device (inverter/smi/cntrl and cmmunicatin gateway, etc.) in the chain by switching a terminatin DIP-switch inside the inverter t ON (mve the switch up). The switch is lcated n the cmmunicatin bard and is marked SW7. NOTE Figure 27: RS485 terminatin switch Only the first and last SlarEdge devices in the chain shuld be terminated. The ther inverters in the chain shuld have the terminatin switch OFF (dwn psitin). T cnnect t the mnitring prtal: 1. Designate a single inverter as the cnnectin pint between the RS485 bus and the SlarEdge mnitring prtal. This inverter will serve as the master inverter. 2. Cnnect the master t the SlarEdge mnitring prtal via the LAN r ZigBee cmmunicatin ptin. T cnfigure the RS485 cmmunicatin bus: All inverters are cnfigured by default as slaves. If recnfiguratin is required: 1. Make sure the ON/OFF switch is OFF. 2. Turn ON the AC t the inverter by turning ON the circuit breaker n the main distributin panel. WARNING! ELECTRICAL SHOCK HAZARD. D nt tuch uninsulated wires when the inverter cver is remved. 63

Creating a Wireless ZigBee Cnnectin 3. Use the user buttns t cnfigure the cnnectin. T set the inverter designated as master, select the fllwing in the LCD menus: Cmmunicatin è Server è LAN, ZigBee r Wi-Fi RS485-1 Cnf. è Device Type è SlarEdge RS485-1 Cnf. è Prtcl è Master RS485-1 Cnf. è Slave Detect The system starts autmatic detectin f the SlarEdge slave inverters cnnected t the master inverter. The inverter shuld reprt the crrect number f slaves. If it des nt, verify the cnnectins and terminatins. 4. Verify the cnnectin f the master t the SlarEdge mnitring prtal, as described in Verifying the Cnnectin n the facing page. Creating a Wireless ZigBee Cnnectin This cmmunicatin ptin enables using a ZigBee cnnectin t cnnect ne r several devices t the SlarEdge mnitring prtal. The ZigBee device is prvided with a user manual, which shuld be reviewed prir t cnnectin. It is available n the SlarEdge website at http://www.slaredge.cm/grups/prducts/cmmunicatin (under ZigBee). Creating a Wi-Fi Cnnectin This cmmunicatin ptin enables using a Wi-Fi cnnectin fr cnnecting the device t the SlarEdge mnitring prtal. The Wi-Fi kit can be purchased separately and assembled during system installatin. The Wi- Fi kit is prvided with a user manual, which shuld be reviewed prir t cnnectin. It is available n the SlarEdge website at http://www.slaredge.cm/grups/prducts/cmmunicatin (under Wi-Fi). 64

Chapter 7: Setting Up Cmmunicatin Verifying the Cnnectin After cnnecting and cnfiguring a cmmunicatin ptin, perfrm the fllwing steps t check that the cnnectin t the mnitring server has been successfully established. 1. Clse the inverter cver: Attach the inverter cver and secure it by tightening the screws with a trque f 9.0 N*m/ 6.6 lb.*ft. Fr prper sealing, first tighten the crner screws and then the tw central screws (see als Figure 16). 2. Turn ON the AC t the inverter by turning ON the circuit breaker n the main distributin panel. 3. Wait fr the inverter t cnnect t the SlarEdge mnitring prtal. This may take up t tw minutes. A status screen similar t the fllwing appears n the LCD panel: V a c [ V ] V d c [ V ] P a c [ w ] 2 4 0. 7 1 4. 1 0. 0 P _ O K : 0 0 0 / 0 0 0 < S _ O K > - - - - - - - - - - - - - - - O F F S_OK: Indicates that the cnnectin t the SlarEdge mnitring prtal is successful. If S_OK is nt displayed, refer t Errrs and Trubleshting n the next page. 65

Appendix A: Errrs and Trubleshting Appendix A: Errrs and Trubleshting This appendix describes the errr messages that appear n the LCD panel when an errr ccurs, and hw t trublesht them. Trubleshting Cmmunicatin - S_OK is Nt Displayed If S_OK is nt displayed, perfrm the fllwing: Trubleshting Ethernet Cmmunicatin When Ethernet cmmunicatin is used, the Server Cmmunicatin Status windw can be used t identify the lcatin f the errr: S e r v e r : L A N < S _ O K > S t a t u s : < O K > x x x x x x x x < E R R O R M E S S A G E > xxxxxxxx is a string f 1s and 0s shwing an eight-bit cmmunicatin cnnectin status. 1 indicates OK and 0 indicates an errr. The pssible errrs and their trubleshting are detailed in the fllwing table: Bit Lcatin 1st Errr Message Errr Descriptin Trubleshting LAN Discnnected An Ethernet physical cable cnnectin fault: The Ethernet link r physical Ethernet cable are nt cnnected prperly Check the cable pin-ut assignment and cable cnnectin. Refer t Creating an Ethernet (LAN) Cnnectin n page 57 2nd DHCP Failed, r Invalid DHCP Cnfig The inverter failed t get a valid IP address frm the DHCP server, r The DHCP/static IP settings in the inverter are nt the same as thse f the ruter. Check the ruter and invertercnfiguratin. Cnsult yur netwrk IT. 3rd Gateway Ping Failed The cnnectin t the ruter is nt available: Ping t the first lcal switch/ruter failed (LAN errr) Check the physical cnnectin t the switch/ruter. Check that the link LED at the ruter /switch is lit (indicating phy-link). If OK - cntact yur netwrk IT, therwise replace the cable r change it frm crss t straight cnnectin. 4th G Server Ping Failed The cnnectin t the Cnnect a laptp and check 66

Appendix A: Errrs and Trubleshting Bit Lcatin Errr Message Errr Descriptin Trubleshting Internet is nt available: Ping t ggle.cm failed fr internet cnnectin. If internet access is unavailable, cntact yur IT admin r yur internet prvider. Fr W-IFI netwrks, ensure that username and passwrd are as defined in the internet prvider AP/ruter. 5th 6th 7th 8th Server x Ping Failed Tcp Cnnect. Failed Ping t redundant server #x failed The cnnectin t the SlarEdge server was nt established: Cmmunicatin with the server failed Check the SlarEdge server address, under LAN Cnf submenu: Address: prd.slaredge.cm Prt: 22222 Check with yur netwrk administratr whether a firewall r anther device is blcking transmissin. 67

Trubleshting RS485 Cmmunicatin Trubleshting RS485 Cmmunicatin 1. If the message Master Nt Fund appears, the master device is nt respnsive r the RS485 cable is nt cnnected. Check the cnnectins t the master device and fix if required. 2. If after slave detectin the number f slaves reprted in the master is smaller than the actual number f slaves, yu can use the slave list 1 t identify missing slaves and trublesht cnnectivity prblems, as described belw. T shw the slave list n the master device: 1. After slave detectin, if slaves were detected, an additinal menu is displayed in the RS485-X Cnf. menu: Slave List. If the number f detected slaves des nt match the number f slaves cnnected t the master, use the slave list t check fr missing slaves, and check their cnnectin. D e v i c e T y p e < S E > P r t c l < M > D e v i c e I D < 1 > S l a v e D e t e c t < # > S l a v e L i s t < # > 2. Select Slave List. A list shwing serial numbers f the detected slaves is displayed. Fr example: 5 0 0 0 F E 0 1-4 F 5 0 0 0 F E 0 2-5 0.. 3. T view the details f a detected slave device, select its serial number entry. The fllwing infrmatin is displayed: I D : 5 0 0 0 F E 0 1-4 F L a s t C m m u n i c a t i n 1 7 / 0 2 / 2 0 1 5 1 4 : 2 4 : 0 1 ID: the device serial number Last Cmmunicatin: the date and time (dd:mm:yy 24h) the device last cmmunicated with the master device. If this device is detected fr the first time after the master wakeup, N/A appears fr this infrmatin. 1 Available frm CPU versin 3.14xx and later. 68

Appendix A: Errrs and Trubleshting Additinal Trubleshting 1. Check that the mdem r hub/ruter is functining prperly. 2. Check that the cnnectin t the internal cnnectr n the cmmunicatin bard is prperly dne. 3. Check that the selected cmmunicatin ptin is prperly cnfigured. 4. Use a methd independent f the SlarEdge device t check whether the netwrk and mdem are perating prperly. Fr example, cnnect a laptp t the Ethernet ruter and cnnect t the Internet. 5. Check whether a firewall r anther type f netwrk filter is blcking cmmunicatin. 6. Fr ZigBee trubleshting, refer t the ZigBee installatin manuals. Errr Cdes The errr messages include an errr number and a descriptin, and have the fllwing frmat: E r r r c d e X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X An errr message is displayed fr 30 secnds, after which the inverter waits the necessary recnnectin time and then restarts. During this time, the LCD displays the Waking Up message and the remaining time t recnnectin. The errr cde numbers may differ depending n the inverter type (single phase r three phase) as described in the table belw. 69

Errr Cdes WARNING! All Warnings and Cautins in this manual shuld be adhered t while trubleshting an errr. Errr # Single Phase Errr # Three Phase LCD Message Descriptin Trubleshting N/A 1-4 Fan # Failure One f the fans is nt wrking Check the fan status screen ("Fan Status " n page 52. If required, replace the fan (a replacement kit is available frm SlarEdge). 4, 5, 8, 12, 18-23, 39, 42, 45 45, 48, 50-53, 94, 108-111,113 SW Errr Internal sftware errr If the fault persists, cntact SlarEdge Supprt. The lines cnnectins t the inverter are incrrect, fr N/A 112 Wrng AC cnnectin example: AC line 1 frm the grid is cnnected t line 2 at the inverter s there is n 120deg between L2 t L1 Switch between L1 and L2 r L2 and L3 cnnectins and L3 t L2 at the inverter side. The internal hardware that measures AC current has If the fault persists: 9, 13 N/A AC Current Surge measured substantially high utput currents. This may ccur because f changes in the AC vltage r a switching lad near the site. Check the AC cnnectin t the inverter Check with the grid peratr if a large surge surce r irregular lad exists near the site. 70

Errr Cdes Errr # Single Phase Errr # Three Phase LCD Message Descriptin Trubleshting If the grid des nt have prblems cntact SlarEdge supprt. Grund faults may ccur due t insufficient insulatin t the grund. WARNING! ELECTRICAL SHOCK HAZARD. D nt tuch uninsulated wires when the inverter cver is remved. Only a qualified technician shuld handle this prblem, and 10, 37, 38 76, 77, 90 Grund Current - RCD Grund current surge. The internal hardware that measures grund fault has measured substantially high grund currents. nly after taking prper precautins. 1. Turn the inverter ON/OFF switch t OFF. 2. Wait five minutes fr the input capacitrs t discharge. 3. Discnnect the AC breaker. 4. Discnnect the DC inputs. 5. Cnnect each DC string separately, turn the AC and the inverter ON/OFF switch t ON, until the errr appears fr the faulty string. D nt cnnect strings with a grunding fault t the inverter. 71

Errr Cdes Errr # Single Phase Errr # Three Phase LCD Message Descriptin Trubleshting Fr further dcumentatin abut pssible grund current errr surces and slutins, cntact SlarEdge Supprt. A certified installer must fix the faulty string befre cnnecting it t the inverter. If the fault persists: 14 58/59/60 AC Vltage T High (Line 1/2/3) AC vltage surge. The internal hardware that measures AC vltage has measured substantially high sudden utput vltage Check the AC cnnectin t inverter. Verify that the inverter is set t the crrect cuntry. Check with the grid peratr if a large surge surce r irregular lad exists near the site. Verify that the utput wire size matches the distance between the inverter and the lcatin f the grid cnnectin. Use a larger gauge wire fr the AC utput. Refer t the AC Wiring Applicatin Nte, available n the SlarEdge website at http://www.slaredge.cm/files/pdfs/applicatinnte-recmmended-wiring.pdf 15 102 DC Vltage T High DC vervltage. The input DC vltage exceeds the maximum supprted level. The SlarEdge system nrmally eliminates DC vervltage errrs: When DC vervltage is detected, the inverter shuts 72

Errr Cdes Errr # Single Phase Errr # Three Phase LCD Message Descriptin Trubleshting ff the pwer ptimizers and restarts. If the fault persists: Turn OFF the inverter ON/OFF switch. If after five minutes, the LCD panel des nt shw a lw safety vltage (1V per ptimizer), check which string is malfunctining and recheck its cnnectins t the inverter. Prceed accrding t Pwer Optimizer Trubleshting n page 78 Re-cmmissin all inverters in the site, as described in Cmmissining the Installatin n page 29 16 123 Hardware Errr Internal hardware errr If the fault persists, cntact SlarEdge Supprt. If the fault persists: 17 104 Temperature T High Over temperature Verify that prper clearances exist arund the inverter. Make sure that the heat-sink fins are clear f dirt and bstacles. Reinstall in a cler lcatin. 24 N/A Faulty Temp. Sensr Brken r uncnnected Temperature sensr If the fault persists, cntact SlarEdge Supprt. 73

Errr Cdes Errr # Single Phase Errr # Three Phase LCD Message Descriptin Trubleshting If the fault persists: 25 121 Islatin Fault PV Islatin fault. The inverter has detected the PV slar array is nt prperly islated frm grund earth. The islatin is checked each time the inverter starts Check the PV installatin fr islatin prblems and grund leakage. Only a certified PV installer must fix the faulty string befre cnnecting it t the inverter. up. Refer t http://www.slaredge.cm/files/pdfs/ applicatin_nte_islatin_fault_trublesht ing.pdf 26 122 Faulty AC Relay The AC relay failed during wake-up tests. If the fault persists: Discnnect inverter frm AC grid. Cntact SlarEdge Supprt. 27, 153 95, 106, 120, 125, 126 Hardware Errr Internal hardware errr. If the fault persists, cntact SlarEdge supprt. 28 N/A RCD Sensr Errr The RCD measurement has failed during the wake-up test phase. If the fault persists, cntact SlarEdge supprt. Check the grid cnnectin. 29-30 N/A Phase Balance Errr The mnitring hardware that checks the balance f each phase (L1-N and L2-N) has exceeded allwed limit. Check the GND wire cnnectin. Check the L1, L2 and Neutral wire cnnectins. Verify symmetric lad between L1 and L2. Cnsult the lcal grid authrity. 74

Errr Cdes Errr # Single Phase Errr # Three Phase LCD Message Descriptin Trubleshting 31, 33 64/65/66 AC Vltage T High (Line 1/2/3) Grid vltage is abve the limit permitted in this cuntry. Verify that the inverter is set t the crrect cuntry. Turn OFF the inverters in the site and verify AC grid vltage. If the inverter is lcated far frm the cnnectin pint t the grid, use a larger gauge AC wire. Cnsult the grid peratr. If permitted by lcal authrities, use the SlarEdge Cnfiguratin Tl t change the settings. 32, 41 61/62/63, 67/68/69 AC Vltage T Lw Grid vltage is belw the limit permitted in this cuntry. Verify that the inverter is set t the crrect cuntry. Cnsult the grid peratr. If permitted by lcal authrities, use the SlarEdge Cnfiguratin Tl t changethe settings. 34 79/80/81 AC Freq T High (Line 1/2/3) Grid frequency is abve the limit permitted in this cuntry. Handle this in the same manner as errr 32. 35 82/83/84 AC Freq T Lw (Line 1/2/3) Grid frequency is belw the limit permitted in this cuntry. Handle this in the same manner as errr 32. 75

Errr Cdes Errr # Single Phase Errr # Three Phase LCD Message Descriptin Trubleshting 36 72/74/75 DC Injectin (Line 1/2/3) DC feed detected n the AC utput. If the fault persists, cntact SlarEdge supprt. 40 N/A Islanding AC grid vltage malfunctins. The inverter has shut ff due t islanding. When AC vltage returns, the inverter shuld restart after sme time (time depends n cuntry grid cnnectin cdes). If the prblem persists, then cnsult with thegrid peratr whether frequent AC disruptins have ccurred at the site. 43 N/A Internal HW Errr Internal hardware errr. If the fault persists, cntact SlarEdge supprt. 44 44 N Cuntry Selected The inverter is nt cnfigured t any cuntry. Select the cuntry, as described in Cuntry and Grid n page 42. Change the Phase Balance ptin in the Inverter s LCD menu t Disable. Refer t Pwer Cntrl n page 45, and t 46 Phase Unbalance the SlarEdgePhase Balancing Manual, available n the SlarEdge website at http://www.slaredge.cm/files/pdfs/phase_balancing_ cnnectin_guide.pdf N/A 103, 119 UDC Min / DC Vltage T Lw The input DC vltage is belw the minimum level that is supprted. Turn the inverter OFF and then ON. If this fault persists, cntact SlarEdge supprt. 76

Errr Cdes Errr # Single Phase Errr # Three Phase LCD Message Descriptin Trubleshting N/A 49 Cmmunicatin Errr Internal sftware errr. If this fault persists, cntact SlarEdge supprt. N/A 78 Grid Sync Errr Grid vltage r frequency is unstable. If this fault persists, cntact SlarEdge supprt. N/A 91/92/93, 96/97/98. AC Over Current Line 1/2/3 Grid errr. If this fault persists, cntact SlarEdge supprt. N/A 99-101 AC Vltage T High Line 1/2/3 Grid errr. Turn the inverter OFF and then ON. If this fault persists, cntact SlarEdge supprt. N/A 105 Temperature T Lw Under temperature. If this fault persists, reinstall the inverter in a warmer place. N/A 124 Grund Current RCD Internal hardware errr. If this fault persists, cntact SlarEdge supprt. 150, 151 150, 151 Arc Fault Detected An arc was detected n the DC side. Refer t Inverter Arc Detectin and Interruptin n page 1. 152 152 Arc detectr self-test failed The arc detectr is checked every time the inverter starts up. The internal hardware that measures arcs failed during wake-up tests. Refer t Inverter Arc Detectin and Interruptin n page 1. 77

Pwer Optimizer Trubleshting Pwer Optimizer Trubleshting If the inverter status screen indicates that nt all pwer ptimizers are paired r nt all are reprting (P_OK xxx/yyy, and x<y), thse ptimizers can be identified thrugh the LCD. Refer t http://www.slaredge.cm/files/pdfs/prducts/inverters/nn-respnding-pwerptimizers.pdf Prblem Pssible Cause Pssible Slutin String vltage is 0V String vltage nt 0V but lwer than number f ptimizers Output f ne r mre pwer Cnnect all pwer ptimizer ptimizers is discnnected utputs One r mre f the pwer ptimizers are nt cnnected in the Cnnect all pwer ptimizers string One r mre f the mdules are nt Cnnect the mdules t the cnnected prperly t their pwer ptimizer inputs ptimizer inputs Check plarity f the string Wrng plarity cnnectin n ne f utput using a vltmeter and the strings crrect if needed. 78

Appendix A: Errrs and Trubleshting Prblem Pssible Cause Pssible Slutin String vltage is higher than the number f ptimizers WARNING! If the measured vltage is t high, the installatin may nt have a safe lw vltage. PROCEED WITH CARE! A deviatin f ±1% per string is reasnable. Si la tensin mesuree est trp haute, la tensin basse de securite purrait manquer dans l installatin. REDOUBLEZ DE PRECAUTION. Une deviatin de ±1% par string est raisnnable. One r mre extra pwer ptimizer are cnnected in the string Check if an extra pwer ptimizer is cnnected in the string. If nt prceed t next slutin. Verify that nly pwer ptimizers are cnnected in the string and that n mdule A mdule is cnnected directly t the utputs are cnnected withut string, withut a pwer ptimizer. a pwer ptimizer. If the A malfunctin f ne f the pwer ptimizers prblem persists, prceed t the next step. Discnnect the wires that cnnect the pwer ptimizers in the string. Measure the utput vltage f each pwer ptimizer in rder t lcate the pwer ptimizer that des nt utput the 1V safety vltage.if a malfunctining pwer ptimizer is lcated, check its cnnectins, plarity, mdule, and vltage. D nt cntinue befre finding the prblem and replacing the malfunctining pwer ptimizer.if a malfunctin cannt be bypassed r reslved, skip the malfunctining pwer ptimizer, thus cnnecting a shrter string. 79

Pwer Optimizer Trubleshting Prblem Pssible Cause Pssible Slutin SafeDC mde was previusly disabled using the SlarEdge Key Enable the SafeDC using the SlarEdge Key. Pairing t the inverter failed The pwer ptimizers are shaded If yu cnnected the inverter t the SlarEdge mnitring prtal using ne f the cmmunicatin ptins, yu can perfrm pairing remtely. Befre leaving the site, make sure that the inverter ON/OFF switch is ON and S_OK indicatin appears n the LCD t indicate cnnectin t the mnitring prtal. 80

Appendix B: Technical Specificatins Appendix B: Technical Specificatins SE2200 SE3000 SE3500 SE4000 SE4000-16A SE5000 SE6000 Unit Output Rated AC pwer utput 2200 3000 3500 4000 4000 5000 1 6000 W Maximum AC pwer utput 2200 3000 3500 4000 4000 5000 1 6000 W AC utput vltage (nminal) 220/230/240 Vac AC utput vltage range 184 264.5 Vac AC frequency(nminal) 50/60 ±5 Hz Maximum cntinuus utput current 12 16.5 2 19.5 2 22 16 27 27 A Max. cntinuus vercurrent prtectin 12 16.5 2 19.5 2 22 16 27 27 A Residual current detectr/ Residual current step detectr 300/30 ma Inrush current AC (Peak/Duratin) 2.8/20 Aac (rms) / ms 1 4985W when the cuntry is set t Australia;4600W when the cuntry is set t Germany r the Czech Republic. 2 16A when the cuntry is set t Denmark, Prtugal, UK, r Pland. Fr ther cuntries, cntact SlarEdge. 81

Appendix B: Technical Specificatins SE2200 SE3000 SE3500 SE4000 SE4000-16A SE5000 SE6000 Unit Max. utput fault current 38 A Pwer factr range 1 (adjustable frm -0.95 t +0.95) Ttal harmnic distrtin <3% Prtective class Class I Utility mnitring, islanding prtectin, cuntry cnfigurable Yes threshlds Overvltage categry III Input Recmmended Maximum DC pwer 1 (Mdule STC) 2750 3750 4350 5000 5000 6250 7500 W Transfrmer-less, ungrunded Yes Maximum input vltage 500 Vdc Nminal DC input vltage 350 Vdc Maximum input current 8.5 11.5 13.5 15.5 15.5 19.5 23 Adc Maximum back-feed current 0 Adc Reverse-plarity prtectin Yes 1 Limited t 135% f AC pwer. 82

Appendix B: Technical Specificatins SE2200 SE3000 SE3500 SE4000 SE4000-16A SE5000 SE6000 Unit Grund-fault islatin detectin 600 kω Sensitivity Overvltage categry III Maximum inverter efficiency 97.6 % Eurpean weighted efficiency 97.6 97.6 97.5 97.5 97.5 97.4 97.4 % Night-time pwer cnsumptin <2.5 W Additinal Features Supprted cmmunicatin interfaces RS485, RS232, Ethernet, ZigBee (ptinal) Standard Cmpliance Safety IEC-62103 (EN50178), IEC-62109 Grid cnnectin standards VDE-AR-N-4105, VDE 0126-1-1, AS-4777, RD-1663, DK 5940 Emissins IEC61000-6-2, IEC61000-6-3, IEC61000-3-11, IEC61000-3-12, FCC part 15 class B RHS Yes Installatin Specificatins AC utput Cable Gland - diameter 9-16 mm DC input 1 MC4 pair 2 MC4 pairs Dimensins (W x L x H) 540 x 315 x 172 540 x 315 x 191 mm Weight 20.2 21.7 kg Cling Natural Cnvectin 83

Appendix B: Technical Specificatins SE2200 SE3000 SE3500 SE4000 SE4000-16A SE5000 SE6000 Unit Nise (typical) <50 dba Operating temperature range 1-20 - +50 (M40 versin -40 t + 50) C Maximum altitude 2000 m Operating humidity nn cndensing <95 % Prtectin Rating/Envirnmental categry IP65 Outdr and Indr Pllutin degree classificatin (inside/utside) 2/3 Bracket munted (bracket prvided) Recmmended circuit breaker/fuse size t use at the cnnectin pint f the SlarEdge inverter t the grid: Inverter Maximum Output Current (A) Suggested Fuse Rating (A) SE2200 12 16 SE3000 16.5 20 SE3500 19.5 25 SE4000 22 25 SE4000-16A 16 20 1 Fr inverter pwer de-rating refer t the applicatin nte at the fllwing link: http://www.slaredge.cm/files/pdfs/se-temperature-derating-nte.pdf 84

Appendix B: Technical Specificatins Inverter Maximum Output Current (A) Suggested Fuse Rating (A) SE5000 27 32 SE6000 27 32 85

Technical Specificatins - Three Phase Inverters Technical Specificatins - Three Phase Inverters SE4K 1 - SE12.5K SE4K SE5K SE7K SE8K SE9K SE10K SE12.5K Unit Output Rated AC pwer utput 4000 5000 7000 8000 9000 10000 12500 VA Maximum AC pwer utput 4000 5000 7000 8000 9000 10000 12500 VA AC utput vltage line t line / line t neutral (nminal) 380/220; 400/230 Vac AC utput vltage range 184 264.5 Vac AC frequency 50/60 ± 5 Hz Maximum cntinuus utput current (per phase) 6.5 8 11.5 13 14.5 16 20 A Maximum cntinuus vercurrent prtectin 6.5 8 11.5 13 14.5 16 20 A Residual current detectr / Residual Current step detectr 300 / 30 ma 1 SE4K mdel is available in sme cuntries; refer t the Certificatins categry in http://www.slaredge.cm/grups/supprt/dwnlads 86

SE4K - SE12.5K SE4K SE5K SE7K SE8K SE9K SE10K SE12.5K Unit Grid supprted three phase 3 / N / PE (WYE with Neutral) Inrush current AC (Peak/Duratin) 3/20 Aac(rms) / ms Maximum utput fault current 33 Pwer factr range 1 (adjustable frm -0.8 t +0.8) Ttal harmnic distrtin <3% Prtective class Class I Utility mnitring, islanding prtectin, cnfigurable Pwer Factr, cuntry cnfigurable Yes threshlds Overvltage categry III Input Maximum DC pwer (Mdule STC) 5400 6750 9450 10800 12150 13500 16850 W Transfrmer-less, ungrunded Yes Maximum input vltage 900 Vdc Nminal DC input vltage 750 Vdc Maximum input current 7 8.5 12 13.5 15 16.5 21 Adc Maximum back-feed current 0 Adc 87

SE4K - SE12.5K SE4K SE5K SE7K SE8K SE9K SE10K SE12.5K Unit Reverse-plarity prtectin Yes Grund-fault islatin detectin 1MΩ Sensitivity Overvltage categry III Maximum inverter efficiency 98 % Eurpean weighted efficiency 97.3 97.3 97.3 97.5 97.5 97.6 97.7 % Night-time pwer cnsumptin < 2.5 W Additinal Features Supprted cmmunicatin interfaces Standard Cmpliance Safety Grid cnnectin standards 1 Emissins WEEE, RHS Installatin Specificatins RS485, Ethernet, ZigBee (ptinal), Wi-Fi (ptinal) IEC-62103 (EN50178), IEC-62109 VDE 0126-1-1, VDE-AR-N-4105, AS-4777, G83 / G59 IEC61000-6-2, IEC61000-6-3, IEC61000-3-11, IEC61000-3-12, FCC part15 class B Yes 1 Fr all standards refer t the Certificatins categry in http://www.slaredge.cm/grups/supprt/dwnlads. 88

SE4K - SE12.5K SE4K SE5K SE7K SE8K SE9K SE10K SE12.5K Unit AC utput Cable Gland - diameter 15-21 mm DC input 2 MC4 pairs Dimensins (WxLxH) 540 x 315 x 260 mm Weight 33.2 kg Operating temperature range 1-20 - +60 (M40 versin -40 t + 60) C Operating humidity nn cndensing <95 % Cling Fan (user replaceable) Nise (typical) < 50 dba Prtectin rating/ Envirnmental categry IP65 Outdr and indr Maximum altitude 2000 m Pllutin degree classificatin (inside/utside) 2/3 Bracket munted (bracket prvided) 1 Fr inverter pwer de-rating refer t the applicatin nte at the fllwing link: http://www.slaredge.cm/files/pdfs/se-temperature-derating-nte.pdf 89

SE15K - SE33.3K SE15K - SE33.3K 1 SE15K SE16K SE17K SE25K SE27.6K SE33.3K Unit Output Rated AC pwer utput 15000 16000 17000 25000 27600 33300 VA Maximum AC pwer utput 15000 16000 17000 25000 27600 33300 VA AC utput vltage line t line / line t neutral (nminal) 380/220; 400/230 480/277 Vac AC utput vltage range 184 264.5 244-305 Vac AC frequency 50/60 ± 5 Hz Maximum cntinuus utput current (per phase) 23 25.5 26 38 40 40 @220V A Maximum cntinuus vercurrent prtectin 23 25.5 26 38 40 40 A Residual current detectr / Residual Current step detectr 300 / 30 ma Grid supprted three phase 3 / N / PE (WYE with Neutral) V 1 The SE33.3K mdel requires a medium vltage transfrmer 90

SE15K - SE33.3K SE15K SE16K SE17K SE25K SE27.6K SE33.3K Unit Aac Inrush current AC (Peak/Duratin) 3/20 3.1/20 4.2/20 (rms) / ms Maximum utput fault current 40 A Pwer factr range 1 (adjustable frm +/-0.9 t 1.0) Ttal harmnic distrtin <3% Prtective class Class I Utility mnitring, islanding prtectin, cnfigurable Pwer Factr, cuntry cnfigurable Yes threshlds Overvltage categry III Input Maximum DC pwer (Mdule STC) 20250 21600 22950 33750 37250 45000 W Transfrmer-less, ungrunded Yes Maximum input vltage 900 1000 Vdc Nminal DC input vltage 750 840 Vdc Maximum input current 23 25 26 37 40 40 Adc Maximum back-feed current 0 Adc Reverse-plarity prtectin Yes 91

SE15K - SE33.3K SE15K SE16K SE17K SE25K SE27.6K SE33.3K Unit Grund-fault islatin detectin 1MΩ Sensitivity Overvltage categry III Maximum inverter efficiency 98 98.5 % Eurpean weighted efficiency 97.6 97.7 97.7 98 98 98.3 % Night-time pwer cnsumptin < 2.5 <4 W Additinal Features Supprted cmmunicatin interfaces RS485, Ethernet, ZigBee (ptinal), Wi-Fi (ptinal) DC Safety Unit (ptinal) 2-ple Discnnectin N/A 1000V / 40A DC Surge Prtectin N/A Type II, field replaceable DC Fuses n Plus & Minus N/A Optinal, 20A Cmpliance N/A UTE-C15-712-1 Standard Cmpliance Safety IEC-62103 (EN50178), IEC-62109, AS3100 92

SE15K - SE33.3K SE15K SE16K SE17K SE25K SE27.6K SE33.3K Unit Grid cnnectin standards 1 VDE-AR-N-4105, G59/3, AS-4777, EN 50438, VDE 0126-1-1, CEI-021, BDEW 2, CEI-016 3 ; Emissins IEC61000-6-2, IEC61000-6-3, IEC61000-3-11, IEC61000-3-12 WEEE, RHS Yes Installatin Specificatins AC utput Cable Gland - diameter 15-21 mm DC input 2 MC4 pairs 3 MC4 pairs; with ptinal DC safety unit: cable glands - diameter 2-4mm Dimensins (HxWxD) 540 x 315 x 260 mm Dimensins with Safety Unit (HxWxD) N/A 775 x 315 x 260 mm Weight 33.2 42 kg Weight with Safety Unit N/A 45 kg Operating temperature range 4-20 - +60 (M40 versin -40 t + 60) C Operating humidity nn cndensing <95 % Cling Fan (user replaceable) 1 Fr all standards refer t the Certificatins categry in http://www.slaredge.cm/grups/supprt/dwnlads. 2 Mdels SE27.6K and SE33.3K nly 3 Mdels SE27.6K and SE33.3K nly 4 Fr inverter pwer de-rating refer t the applicatin nte at the fllwing link: http://www.slaredge.cm/files/pdfs/se-temperature-derating-nte.pdf 93

SE15K - SE33.3K SE15K SE16K SE17K SE25K SE27.6K SE33.3K Unit Nise (typical) <50 <55 dba Prtectin rating/ Envirnmental categry IP65 Outdr and indr Maximum altitude 2000 m Pllutin degree classificatin (inside/utside) 2/3 Bracket munted (bracket prvided) Recmmended circuit breaker/fuse size t use at the cnnectin pint f the SlarEdge inverter t the grid: Inverter Maximum Output Current (A) Suggested Fuse Rating (A) SE4K 6.5 10 SE5K 8 10 SE7K 11.5 16 SE8K 13 16 SE9K 14.5 20 SE10K 16 20 SE12.5K 20 25 SE15K 23 25 SE16K 25.5 32 SE17K 26 32 SE25K 38 63 94

DC Safety Unit Specificatins DC Safety Unit Specificatins Inverter Maximum Output Current (A) Suggested Fuse Rating (A) SE27.6K 40 63 SE33.3K 40 63 Feature 2-ple Discnnectin DC Surge Prtectin DC Fuses n Plus & Minus Weight Cmpliance Prtective Class Specificatin 1000V / 40A Type II, field replaceable Optinal, 20A 2.7 kg UTE-C15-712-1 Class II 95

Appendix C: Mechanical Specificatins Appendix C: Mechanical Specificatins The fllwing figures prvide dimensins f the munting brackets fr the single and three phase inverters. Type 1 munting bracket weighs 2.87 lbs. / 1.3 kg. Type 2 munting bracket weighs 0/9 lb. / 0.4 kg Single Phase Inverter and Munting Bracket Type 1 Figure 28: Single phase inverter with type 1 bracket - frnt and rear views 96

Appendix C: Mechanical Specificatins Figure 29: Single phase inverter with type 1 bracket - side and bttm views 97

Single Phase Inverter and Munting Bracket Type 2 Figure 30: Single phase inverter munting bracket Single Phase Inverter and Munting Bracket Type 2 Figure 31: Single phase inverter with bracket type 2 - frnt, side and rear views 98

Appendix C: Mechanical Specificatins Figure 32: Inverter munting bracket Type 2 99

Three Phase Inverter and Munting Bracket Type 1 Three Phase Inverter and Munting Bracket Type 1 Figure 33: Three phase inverter with bracket type 1 - frnt and rear views 100

Appendix C: Mechanical Specificatins Figure 34: Three phase inverter with bracket type 1 side and tp views 101

Three Phase Inverter and Munting Bracket Type 2 Figure 35: Three phase inverter munting bracket Three Phase Inverter and Munting Bracket Type 2 Figure 36: Three phase inverter with bracket type 2 - frnt, side and rear views 102

Appendix D: Cnnecting the AC and DC Strings t the DC Safety Unit Appendix D: Cnnecting the AC and DC Strings t the DC Safety Unit Extended pwer three phase inverters (SE25K-SE33.3K) can be supplied with an ptinal integrated DC Safety Unit. The DC Safety Unit includes: Mechanical DC switch (2-ple discnnectin) DC surge prtectin (Type II) DC fuses (plus & minus; ptinal) This sectin describes cnnectins t DC Safety Unit with r withut fuses. The fllwing figure illustrates the DC Safety Unit supplied with fuses. Figure 37: Inside the DC Safety Unit with fuses 103

Cnnecting the AC Grid t the Inverter Cnnecting the AC Grid t the Inverter Use a five-wire cable fr this cnnectin. The maximum wire size fr the input terminal blcks is 16mm². T cnnect the AC grid t the inverter via the DC Safety Unit: 1. Turn OFF the fllwing: The inverter ON/OFF switch The AC circuit breaker The DC Safety Switch Unit 2. Open the inverter cver: Release the Allen screws and carefully mve the cver hrizntally befre lwering it. CAUTION! When remving the cver, make sure nt t damage internal cmpnents. SlarEdge will nt be held respnsible fr any cmpnents damaged as a result f incautius cver remval. 3. Lsen the screws n the frnt cver f the DC Safety Unit, as shwn belw: 4. Remve the DC Safety Unit cver. Figure 38: Opening the DC Safety Unit cver 5. Strip 35 cm f the external cable insulatin and strip 8 mm f the internal wire insulatin. Figure 39: Insulatin stripping AC 6. Open the AC cable gland and insert the cable thrugh the gland (see Figure 37). 7. Cnnect the grunding wire t the equipment grunding terminal in the DC Safety Unit. NOTE Cnnect the equipment grunding befre cnnecting the AC wires t the AC terminal blck. 104

Appendix D: Cnnecting the AC and DC Strings t the DC Safety Unit 8. Insert the remaining fur wires thrugh the AC cnduit t the inverter, and cnnect them t the apprpriate terminal blcks in the inverter accrding t the labels n the terminal blcks (N, L1, L2 and L3). Figure 40: Three Phase Inverter AC Terminals 9. Tighten the screws f each terminal with a trque f 1.2-1.5 N*m / 0.88-1.1 lb*ft. 10. Check that the wires are fully inserted and cannt be pulled ut easily. 11. Tighten the AC cable gland with a trque f 2.8-3.3 N*m / 2.0-2.4 lb*ft. 12. Verify that there are n uncnnected wires. NOTE If pwer cntrl is enabled, it is imprtant t respect the rder f grid lines cnnectin t the inverter. A 120deg phase difference shuld be kept between L1 t L2 and between L2 t L3 (L1-L2-L3 and nt, fr example L1-L3-L2). If the grid lines are nt in this rder, an errr is displayed n the LCD and the inverter will nt prduce pwer. Cnnecting the Strings t the DC Safety Unit Up t three strings may be cnnected in parallel t the DC input pairs f the switch. The terminals are suitable fr cnnectin f cpper cnductrs nly. T cnnect the strings t the DC Safety Unit: 1. Strip 8 mm f the DC wire insulatin. 2. Insert the wires int the DC input glands in the DC Safety Unit. 105

Cnnecting the Strings t the DC Safety Unit 3. Cnnect the DC wires accrding t the DC+ and DC- labels: Fr DC terminals withut fuses: Use a standard flat-blade screwdriver t cnnect the wires t the spring-clamp terminals. The screwdriver blade shuld fit freely in the terminal pening. T large a blade can crack the plastic husing. Insert the screwdriver and press the release mechanism and pen the clamp. Insert the cnductr int the rund pening and remve the screwdriver the wire is autmatically clamped. Figure 41: Spring-clamp terminals Fr DC terminals with fuses: Insert the wires int the side penings. Fasten the screws at the tp f the fuses. Figure 42: DC cnnectin with fuses 106

Appendix D: Cnnecting the AC and DC Strings t the DC Safety Unit 4. Verify that there are n uncnnected wires. 5. Clse the DC Safety Unit cver. Attach the cver and secure it by tightening the fur screws with a trque f 1.2 N*m / 0.9 ft.*lb. 6. Ensure prper cable entry sealing; inspect the entire cable run and use standard sealants t avid water penetratin. 107

Appendix E: Safe DC Appendix E: Safe DC When AC supply t the inverter is shut ff (by shutting ff the AC breaker at the site), r when the inverter ON/OFF switch is turned t OFF, the DC vltage drps t a safe vltage f 1V per ptimizer. The SlarEdge inverters are certified fr cmpliance with the fllwing standards as discnnectin devices fr PV generatrs, meaning that they can replace a DC discnnect: IEC 60947-3:1999 + Crrigendum: 1999 + A1:2001 + Crrigendum 1:2001 + A2:2005; DIN EN 60947-3 VDE 0660-107:2006-03 IEC 60364-7-712:2002-05 DIN VDE 0100-712:2006-06. In cmpliance with these standards, the discnnectin mechanism perates as fllws: 1. Turn the inverter ON/OFF switch, lcated at the bttm f the inverter, t OFF, r discnnect the AC by shutting ff the AC breaker at the site. The DC vltage displayed n the inverter LCD begins t decrease. If the AC breaker was shut ff, the LCD des nt display. In this case, wait five minutes. 2. When the DC vltage reaches a safe vltage, the PV cnnectrs at the input t the inverter can be discnnected. A galvanic separatin then exists between the PV array and the inverter. WARNING! Under single fault cnditins, the Safe DC vltage is nly guaranteed when using mdules f up t: 95Vc when using the single phase inverter 70Vc when using the three phase inverter 108

Appendix F: External Fan Maintenance and Replacement Appendix F: External Fan Maintenance and Replacement The three phase inverters have tw fans: ne is internal and requires a SlarEdge technician t replace and the ther is accessible frm the utside f the inverter. A fan replacement kit is available frm SlarEdge. Fan Maintenance Figure 43: Inverter external fan 1. At least nce a year, pen the fan screen and clean the accumulated dust using a brush. 2. Check the Fan Status screen n the LCD (refer t Fan Status n page 52). 3. If ne f the fllwing ccurs, replace the fan as described belw: When the fan stps perating Fan status is Nt Wrking; Befre replacing the fan, turn the inverter AC OFF and ON and check if the status is cleared The fllwing Errr is displayed: External Fan Replacement 1. Turn OFF the inverter ON/OFF switch, and wait until the LCD indicates that the DC vltage is safe (<50V), r wait five minutes befre cntinuing t the next step. WARNING! If yu cannt see the inverter panel, r if a malfunctin is indicated n the LCD panel, wait five minutes fr the input capacitrs f the inverter t discharge. 2. Turn OFF the Safety Switch and the AC switch f the distributin panel. 109

External Fan Replacement 3. Use a Philips screwdriver t unfasten the single screw f the fan cver. 4. Open the fan dr. 5. Discnnect the fan cnnectr and remve the fan. Figure 44: Fan cnnectr 6. Cnnect the fan cnnectr t the new fan. 7. Clse the fan dr and fasten the cver screw. 8. Check the Fan Status n page 52. 110

Appendix G: Replacing and Adding System Cmpnents Appendix G: Replacing and Adding System Cmpnents NOTE If yu are permanently disassembling the installatin r part f it, make sure t use the dispsal methds dictated by lcal regulatins. Replacing an Inverter 1. Turn OFF the inverter ON/OFF switch, and wait until the LCD indicates that the DC vltage is safe (<50V), r wait five minutes befre cntinuing t the next step. WARNING! If yu cannt see the inverter panel, r if a malfunctin is indicated n the LCD panel, wait five minutes fr the input capacitrs f the inverter t discharge. 2. Turn OFF the AC switch f the distributin panel. 3. Open the inverter cver as described in Remving the Inverter Cver n page 56. 4. Discnnect the DC plugs and AC wires frm the inverter. 5. Remve the screws securing the inverter t the munting bracket and remve the inverter frm the munting bracket. NOTE If yu remve the ld inverter and d nt immediately install a new ne, use insulatin tape t islate each f the AC and DC wires 6. Place the new inverter n the munting bracket; insert the screws securing the inverter t the munting bracket. 7. Fllw the instructins f Installing the Inverter n page 18 and Cmmissining the Installatin n page 29. 8. Cnnect the DC and AC wires t the inverter. Adding, Remving, r Replacing Pwer Optimizers 1. Turn OFF the inverter ON/OFF switch, and wait until the LCD indicates that the DC vltage is safe (<50V), r wait five minutes befre cntinuing t the next step. WARNING! If yu cannt see the inverter panel, r if a malfunctin is indicated n the LCD panel, wait five minutes fr the input capacitrs f the inverter t discharge. 111

Adding, Remving, r Replacing Pwer Optimizers 2. Turn OFF the AC switch f the main distributin panel. 3. Discnnect and cnnect the necessary pwer ptimizers. 4. Perfrm pairing and ther prcedures described in Cmmissining the Installatin n page 29 n all inverters t which pwer ptimizers were added r frm which pwer ptimizers were remved. 5. In the mnitring prtal, replace the serial number f the remved pwer ptimizer with serial number f the newly installed pwer ptimizer. 112