Ethernet PFC Sending Application note

Transcription

1 Ethernet PFC Sending , English Version 1.0.0

2 2 General Copyright 2002 by WAGO Kontakttechnik GmbH All rights reserved. WAGO Kontakttechnik GmbH Hansastraße 27 D Minden Phone: +49 (0) 571/ Fax: +49 (0) 571/ [email protected] Web: Technical Support Phone: +49 (0) 571/ Fax: +49 (0) 571/ [email protected] Every conceivable measure has been taken to ensure the correctness and completeness of this documentation. However, as errors can never be fully excluded we would appreciate any information or ideas at any time. We wish to point out that the software and hardware terms as well as the trademarks of companies used and/or mentioned in the present manual are generally trademark or patent protected.

3 Table of Contents 3 TABLE OF CONTENTS 1 Important comments Legal principles Copyright Personnel qualification Intended use Range of validity Description Reference Material Procedure 1: Configuring the ArGoSoft Mail Server Procedure 2: Configuring service for Microsoft Outlook Procedure 3: Configuring the WAGO Ethernet PFC... 11

4 4 Important comments 1 Important comments 1.1 Legal principles Copyright To ensure fast installation and start-up of the units described in this manual, we strongly recommend that the following information and explanation is carefully read and adhered to. This manual is copyrighted, together with all figures and illustrations contained therein. Any use of this manual which infringes the copyright provisions stipulated herein, is not permitted. Reproduction, translation and electronic and photo-technical archiving and amendments require the written consent of WAGO Kontakttechnik GmbH. Non-observance will entail the right of claims for damages Personnel qualification Intended use The use of the product detailed in this manual is exclusively geared to specialists having qualifications in PLC programming, electrical specialists or persons instructed by electrical specialists who are also familiar with the valid standards. WAGO Kontakttechnik GmbH declines all liability resulting from improper action and damage to WAGO products and third party products due to non-observance of the information contained in this manual. For each individual application, the components supplied are to work with a dedicated hardware and software configuration. Modifications are only admitted within the framework of the possibilities documented in the manuals. All other changes to the hardware and/or software and the non-conforming use of the components entail the exclusion of liability on part of WAGO Kontakttechnik GmbH. Please direct any requirements pertaining to a modified and/or new hardware or software configuration directly to WAGO Kontakttechnik GmbH.

5 Important comments Range of validity This application note is based on the stated hardware and software of the specific manufacturer as well as the correspondent documentation. This application note is therefore only valid for the described installation. New hardware and software versions may need to be handled differently. Please note the detailed description in the specific manuals.

6 6 Description 2 Description The purpose of this document is to provide step-by-step procedures for configuring a WAGO Ethernet PFC ( ) for transmittal of messages. In order to demonstrate that s are being transmitted, a mail server is setup using ArGoSoft Mail Server, a freeware product available for download at Microsoft s Outlook is used to view the messages transmitted by the WAGO Ethernet PFC. This document first shows how to configure ArGoSoft and Outlook on a local PC, followed by how to configure and initiate transmittal of messages by the WAGO Ethernet PFC. The procedures in this document have been tested with (but are not limited to) the following hardware/software configuration: Intel Pentium III based PC running Windows 98 Operating System, with Ethernet network interface card ArGoSoft Mail Server version 1.4 Microsoft Outlook 98 WAGO Ethernet Buscoupler, firmware revision 4.0 WAGO pt. Digital Input Module, 24VDC WAGO Industrial Ethernet Switch Ethernet interconnection cables (quantity 2), with straight through connectivity For other details about WAGO I/O please refer to the WAGO Users Manuals. The Users Manuals can be downloaded from the web site

7 Reference Material 7 3 Reference Material 3.1 Procedure 1: Configuring the ArGoSoft Mail Server. Install the ArGoSoft Mail Server, version 1.4, and configure it as follows: A) Start ArGoSoft Mail Server. B) Under Tools Options create a local domain. In the example, the domain is mymailserver.com. Figure 1: Creating a Local Domain in ArGoSoft.

8 8 Reference Material C) Under Tools Users create a new user. In the example, the new user is user1. Enter a Real Name and Password in the fields. Be sure to remember the password, as you will need it later. Figure 2: Creating a User in ArGoSoft.

9 Reference Material Procedure 2: Configuring service for Microsoft Outlook Start Microsoft Outlook, and proceed as follows: Under Tools Services add a new service of type Internet . In the example, the new service is PFC Mail Server. Under User Information, fill in the Name and address fields. The address field must coincide with the user and local domain set up in ArGoSoft. Figure 3: Creating an Internet Service in Outlook.

10 10 Reference Material Under the Servers tab, enter the IP address for the Incoming and Outgoing mail servers. The IP addresses will be that of the local PC. Enter the Account name and Password as they were entered in the ArGoSoft user configuration. Figure 4: Creating an Internet Service in Outlook. C) You will need to close and reopen Outlook for the new service to be active.

11 Reference Material Procedure 3: Configuring the WAGO Ethernet PFC Configure the WAGO Ethernet PFC as follows: Download the Demo.pro project to the Ethernet PFC. A snapshot of the project is shown here. Be certain to copy the libraries SMTP_MAIL.LIB and ETHERNET.LIB into the \LIB2 subdirectory of WAGO-I/O-PRO 32, and insert them into the project. Figure 5: The Demo.pro project. An message will be sent each time the Start bit is set TRUE. In this case, this is accomplished by turning on real world input bit 0.0. If the ArGoSoft Mail Server is running, you should see an message appear in Outlook each time the Start bit is set TRUE. You may need to refresh the Outlook window by hitting F5 to see new messages.

12 WAGO Kontakttechnik GmbH Postfach 2880 D Minden Hansastraße 27 D Minden Phone: 05 71/ Telefax: 05 71/ [email protected] WAGO Corporation USA N120W19129 Freistadt Road PO Box 1015 Germantown, Wi Phone: Fax: Internet: Call Toll Free: DIN-RAIL ( )