Hypercom Key Loading and Management (HKLM) RS232 PPP Key Injection PC Setup Guide

Transcription

1 Hypercom Key Loading and Management (HKLM) RS232 PPP Key Injection PC Setup Guide

2

3 Hypercom Corporation 8888 East Raintree Drive Scottsdale, Arizona USA Corporate Telephone: Corporate Fax: Corporate Web Site: Copyright by Hypercom Corporation. Printed in the United States of America. All Rights Reserved. This publication is proprietary to Hypercom Corporation and is intended solely for use by Hypercom customers. This publication may not be reproduced or distributed for any purpose without the written permission of Hypercom Corporation. The information Hypercom furnishes in this publication is believed to be accurate and reliable. However, the corporation assumes no responsibility for its use and reserves the right to make changes to the publication at any time without notice. Trademarks Hypercom and the Hypercom logo are registered trademarks of Hypercom Corporation. Integrated Enterprise Network is a trademark of Hypercom Corporation. Hypercom has attempted throughout this publication to distinguish proprietary trademarks from descriptive terms by following the capitalization style the manufacturer uses. Every effort was made to supply complete and correct information. Any error in identifying or reflecting any proprietary marks or notices is inadvertent and unintentional. i

4

5 Table of Contents Introduction Guide Organization v Who Should Use This Guide v Guide Conventions v Chapter 1 Overview and Requirements PC Requirements Chapter 2 Setup the PC for Serial PPP FTP Server Setup Windows XP Verify that there is an FTP server on the System Install the FTP server component Prepare the FTP server for use with Turbo Boot PPP Remote Access Service (RAS) Server Setup Windows XP Set up the PPP Connection Configure the PPP Connection Set the Serial Parameters Verify the Connection , rev. B HKLM RS232 PPP Key Injection PC Setup Guide iii

6

7 Introduction This guide explains how to set up HKLM to inject keys using RS232 PPP communication protocols. It describes setting up an FTP Server and PPP Remote Access Server (RAS) on a PC using the Windows XP operating system. Guide Organization The guide contains the following chapters: Chapter 1, Overview and Requirements: list of the PC requirements needed to run HKLM Chapter 2, PC to Serial PPP setup: procedures for setting up the FTP server and PPP RAS server on a PC running the Microsoft Windows XP operating system Who Should Use This Guide This guide is intended for network administrators, operators, or those who oversee the configuration and maintenance of security keys. Guide Conventions This section provides information to help you understand the procedures and concepts presented in this guide. The following special terms and style conventions are used throughout this document: Component names: Special bold text highlights certain items including the names of buttons. This text appears in instructions for specific actions such as clicking buttons, typing in text boxes, and selecting from lists. For example: Click Back to select a different key. Emphasis: Emphasis is indicated by indented text. For example: NOTE: A note contains neutral or positive information supplementing the main text. It is often information that applies only to special cases. IMPORTANT: Important statements draw attention to information crucial to using the product successfully. Pay special attention to Important statements. Clicking with the mouse: This document assumes you are using a mouse or some other pointing device to move within and among windows and dialog boxes. Therefore, when instructions include clicking an item, it means you use the mouse to move the cursor onto the desired item. You then click the mouse button to highlight the item or cause an action to occur. For example: Click the Totals check box to activate the online totals feature , rev. B HKLM RS232 PPP Key Injection PC Setup Guide v

8 Introduction Caution and Warning boxes: When you see a Caution or Warning message, read the information promptly and carefully before proceeding. For example: CAUTION Caution advises that a negative result such as a loss of data may occur. WARNING Warnings provide information that is essential to the safety of the user, the equipment, or both. Failure to do as instructed may result in physical damage. vi Hypercom Corporation , rev. B

9 Chapter 1 Overview and Requirements An Optimum terminal can load new software while in terminal boot mode. The boot communicates with a loading computer using the RS232 PPP FTP protocol. This requires the computer to be setup with two Windows services: FTP Server and RS232 PPP Remote Access Services (RAS). The following chapters provide details about how to set up the services. This chapter provides the hardware and software requirements of the application. PC Requirements These are the minimum requirements: PC Hardware 133-Mhz Intel Pentium-class processor. 128 MB of RAM, 256 MB recommended. 150 MB of hard disk space required. 800 x 600 or higher-resolution display with 256 colors. Microsoft mouse or compatible pointing device. One Ethernet card. One serial communication port. Serial cables (Hypercom Part Number , Rev.A). PC Software Any of the following operating system software must be installed in the PC: Windows XP Professional Windows XP Home Edition Windows 2000 NOTE: Install the latest Windows service packs and critical updates from the Windows Update site , rev. B HKLM RS232 PPP Key Injection PC Setup Guide 1-1

10

11 Chapter 2 Setup the PC for Serial PPP FTP Server Setup Windows XP This chapter describes how to set up the FTP Server and RS232 PPP Remote Access Services (RAS) to load new software while in terminal boot mode. Verify that there is an FTP server on the System Step-by-Step To verify a FTP server on the system: 1. From the Control Panel, double click Add/Remove Programs. The Add/Remove Programs window appears , rev. B HKLM RS232 PPP Key Injection PC Setup Guide 2-1

12 Chapter 2 2. On the Add/Remove Programs window, click Add/Remove Windows Components. 3. The Windows Components Wizard appears. Highlight the Internet Information Services component and then click Details. 4. Check to see if the File Transfer Protocol (FTP) Server component is checked. If not, proceed to next step. 2-2 Hypercom Corporation , rev. B

13 Setup the PC for Serial PPP Install the FTP server component Step-by-Step To install the FTP server component: 1. From Internet Information Services (IIS) window, select the File Transfer Protocol (FTP) Server component. This also automatically selects any component it is dependent upon. Then click OK. 2. Back in the Windows Component Wizard window, the Internet Information Services (IIS) check box should be checked and filled in with gray. Click Next to continue , rev. B HKLM RS232 PPP Key Injection PC Setup Guide 2-3

14 Chapter 2 3. Files will now be copied. 4. Click Finish to close the Windows Component Wizard. The FTP Server is now successfully installed. 2-4 Hypercom Corporation , rev. B

15 Setup the PC for Serial PPP Prepare the FTP server for use with Turbo Boot Step-by-Step To prepare the FTP Server for use with Turbo Boot: NOTE: The standard location for the FTP server is C:\Inetpub\ftproot. 1. Create a directory in C:\Inetpub\ftproot called OS NOTE: In the OS directory, the terminal looks for a file called main.app. 2. Copy main.app to the C:\Inetpub\ftproot\OS directory. 3. The application will be downloaded upon successful connection to the terminal , rev. B HKLM RS232 PPP Key Injection PC Setup Guide 2-5

16 Chapter 2 PPP Remote Access Service (RAS) Server Setup Windows XP Set up the PPP Connection Step-by-Step To set up the PPP connection: 1. On the Control Panel window, double-click Network Connections. 2. The Network Connections window appears. 2-6 Hypercom Corporation , rev. B

17 Setup the PC for Serial PPP 3. On the window, double-click Create a new connection. The New Connection Wizard window appears. 4. Click Next. The Network Connection Type window appears. 5. Select Set up an advanced connection, and then click Next. The Advanced Connection Options window appears , rev. B HKLM RS232 PPP Key Injection PC Setup Guide 2-7

18 Chapter 2 6. Select Connect directly to another computer, and then click Next. The Host or Guest window appears. 7. Select Host, and then click Next. The Connection Device window appears. 8. From the drop down menu, select Communications Port (COM1), and then click Next. The User Permissions window appears. 2-8 Hypercom Corporation , rev. B

19 Setup the PC for Serial PPP 9. Click Next. The Completing the New Connection Wizard window appears. 10. Click Finish to return to the Network Connections window that shows the new connection , rev. B HKLM RS232 PPP Key Injection PC Setup Guide 2-9

20 Chapter 2 Configure the PPP Connection Step-by-Step To configure the PPP connection: 1. Access the Network Connections window, right-click on Incoming Connections, then select Properties. The Incoming Connections Properties window appears. 2. Select the Users tab Hypercom Corporation , rev. B

21 Setup the PC for Serial PPP 3. On the Users tab, select Always allow directly connected devices such as palmtop computers to connect without providing a password, and then select the Networking tab. 4. Select Internet Protocol (TCP/IP), and then click Properties. The Incoming TCIP/IP Properties window appears , rev. B HKLM RS232 PPP Key Injection PC Setup Guide 2-11

22 Chapter 2 5. Select Specify TCP/IP address, and then complete the following: a. In the From field, enter b. In the To field, enter c. Select Allow calling computer to specify its own IP address d. Click OK. The Incoming Connections Properties window appears. 6. Click OK. The Network Connections window appears Hypercom Corporation , rev. B

23 Setup the PC for Serial PPP Set the Serial Parameters Step-by-Step To set the serial parameters: 1. On the Network Connections window, double-click Control Panel. The Control Panel appears. 2. Double-click Phone and Modem Options. The Location Information window appears. 3. Enter your area code, carrier code (if required), and outside line access number. Then, click OK. The Phone and Modem Options window appears , rev. B HKLM RS232 PPP Key Injection PC Setup Guide 2-13

24 Chapter 2 4. On the Modems tab page, select Communications cable between two computers, then click Properties. The Communications cable between two computers Properties window appears. 5. On the Modem tab page and the Maximum Port Speed drop down menu, select the maximum port speed of , and then select the Advanced tab. The advanced options appear Hypercom Corporation , rev. B

25 Setup the PC for Serial PPP 6. Click Change Default Preferences. The Data Connection Preferences appear. 7. Select a port speed of , a flow control of Hardware, and then select the Advanced tab. The Hardware Settings options appear , rev. B HKLM RS232 PPP Key Injection PC Setup Guide 2-15

26 Chapter 2 8. Ensure that Data bits, Parity, and Stop bits are 8, None, and 1, and then click OK to continue. 9. This concludes the configuration of the serial port. Click OK through all windows to return to the Control Panel. 10. Close the Control Panel Hypercom Corporation , rev. B

27 Setup the PC for Serial PPP Verify the Connection After the RAS-PPP-FTP over serial has been set up, you can test the connection by extracting a boot log from an Optimum terminal. Step-by-Step To verify the connection: 1. Connect a terminal to the loading computer using a serial cable. 2. Make sure the computer FTP directory (C:\Inetpub\ftproot\OS) is empty. Delete all files if necessary. 3. Put the terminal into boot transfer mode by power cycling the terminal while holding the Cancel key or reset button. The terminal should generate constant beeps indicating the boot is performing file transfer. Once the transfer has started, the Cancel key or reset button can be released. A RAS icon should appear on the computer system tray indicating the terminal connection. After the transfer is finished, the terminal will reboot automatically. 4. To confirm the success of the file transfer, verify that a boot log file with current date was generated in the computer s c:\inetpub\ftproot\bootlog directory. NOTE: If there is a problem with the file transfer, disable the Windows Firewall from the Windows Control Panel and try again. To perform a software load: Use the Verifying the Connection procedure steps, except (step 2) place the target terminal software into the FTP directory (C:\Inetpub\ftproot\OS) before power cycling the terminal into boot mode. Instead of generating a boot log, the terminal downloads the new files from the OS directory into the terminal , rev. B HKLM RS232 PPP Key Injection PC Setup Guide 2-17

28 Chapter Hypercom Corporation , rev. B

29

30 8888 E. Raintree Dr., Scottsdale Arizona, USA. Tel: Fax: