P-3202H-Bb. G-PON VoIP IAD DEFAULT LOGIN DETAILS. Firmware v1.0 Edition 1, 09/2009. IP Address: Password: 1234

Transcription

1 P-3202H-Bb G-PON VoIP IAD Firmware v1.0 Edition 1, 09/2009 DEFAULT LOGIN DETAILS IP Address: User Name admin Password: 1234 Copyright 2009

2 Device Panels POWER PON ETHERNET 1~4 PHONE 1~2 ON/OFF POWER PORT PHONE 1~2 ETHERNET 1~4 PON PORT RESET 2

3 ENGLISH Overview This device is an Integrated Access Device (IAD) which combines highspeed fiber optic (G-PON) Internet access, a built-in switch, and Voice over IP (VoIP) technology to allow you to use an analog telephone to make phone calls over the Internet. In This Guide, You Will: Make the hardware connections to set up your device. Configure your Internet access using the software built into the device. (In some regions these settings may already be preconfigured by your ISP.) Configure your VoIP settings in order to make phone calls over the Internet using an analog phone. 3

4 Hardware Connections PON: Connect the fiber optic cable from your ISP to this port. 2. ETHERNET: Use an Ethernet cable to connect a computer to one of these ports for initial configuration and/or Internet access. 3. PHONE: Use a telephone cable (and any telephone adapter provided with your device) to connect your telephone to the PHONE 1 port. 4. POWER: Use the power adapter provided with your device to connect an appropriate power source to this socket. 5. Push the power switch to the on position. 4

5 ENGLISH Look at the LEDs (lights) on the top panel of the device. The POWER light blinks during start-up and is green once the device is ready. If it turns red, then that means there has been a failure during the start up routine. Each ETHERNET light turns on if its corresponding port is properly connected to a computer. The lights blink when the device is sending or receiving data through the corresponding port. The PON light stays on if a physical fiber optic connection exists and blinks when transmitting data. If it is off, then it means the device cannot connect to the ISP or an error has occured. The PHONE lights stay on when your SIP account is registered and they blink if the receiver is off the hook. The Web Configurator The Web Configurator allows you to set up your device so that you access the Internet or place VoIP phone calls. 1. Open your browser and enter (the device's default IP address) as the address. 5

6 2. Enter the user name admin (default) and Password, then click the Login button. If the login screen does not display, make sure you allow web browser pop-up windows, JavaScript and Java permissions. Your computer should be also set to get an IP address automatically from a DHCP server. See the User s Guide for more information. Internet Setup This section shows you how to configure your device s connection settings so that you can access the Internet. Be sure to use any connection settings provided by your ISP. This includes user name, password, IP address, and DNS server. 1. Log into the Web Configurator as described in the previous section. 6

7 ENGLISH 2. When the Status screen displays, expand the Network menu in the navigation pane and then click WAN. 3. When the Internet Access Setup screen displays, select an Encapsulation method. If you choose PPPoE encapsulation, then you must enter a User Name and Password. The Service Name is optional, but usually corresponds to the name of the ISP for easy reference later. 7

8 If you choose IP encapsulation, then you must enter a method for obtaining an IP address on your device. Choose Obtain an IP address automatically if your ISP dynamically assigns IP addresses with a DHCP server. Otherwise, choose Static IP Address and enter the information as provided by your ISP. 4. If your ISP uses one or more DNS servers, enter their IP addresses. 5. Finally, click Apply to save your changes. 8

9 ENGLISH VoIP Setup This section shows you how to configure your Voice over IP (VoIP) settings so that you can place calls over the Internet. When you make Internet phone calls, your device utilizes a protocol known as SIP. Be sure to use any connection settings that may have been provided by your VoIP service provider. This includes SIP number, SIP Server Address, and SIP username and password. 1. Log into the Web Configurator as described in the previous section. 2. When the Status screen displays, expand the VoIP menu in the navigation pane and then click SIP. 3. On the SIP Service Provider screen, enter a SIP Service Provider Name in the space provided. 9

10 4. Select Active, then enter the following information as it was provided by your VoIP service provider: SIP Local Port - This is the listening port to which incoming call requests are received. SIP Server Address - This is the IP address or domain name of the SIP server. SIP Server Port - This is the listening port on the SIP server to which outgoing calls are sent. REGISTER Server Address - This is the IP address or domain name of the SIP account registration server. If your VoIP service provider did not give you this information then you can use the SIP server address. REGISTER Server Port - This is the SIP register server s listening port to which registration requests are sent. If your VoIP service provider did not give you this information then you can use the SIP server port number. SIP Service Domain - This is a domain name used by the SIP service. If your VoIP service provider listed the full SIP address, then it is the portion after symbol. For example, if you were given a SIP service domain of then the value you put in this field would be voipprovider.com. 10

11 ENGLISH 5. On the SIP Account screen, select a SIP Account. It does not matter which one if this is your first time configuring this. 6. Select Active SIP Account, then enter the following information (if it was provided by your VoIP service provider): Number - This is the number other people dial when they want to reach you using VoIP. User Name - Enter your SIP account user name. This is not the same as your Internet account user name. Password - Enter your SIP account password. This is not the same as your Internet account password. 7. Finally, click Apply to save your setttings. 11

12 Make Phone Calls Follow these directions to make calls over the Internet. To dial a SIP number that only uses numbers (for example, ), dial the number on your phone s keypad. You can also set up a speed-dial entry, if you want. See the User s Guide for instructions. To dial a SIP number that uses letters or if you want to make a peer-to-peer call, set up a speed-dial entry first. See the User s Guide for instructions. Then, dial the speed-dial number to make the call. To call regular telephone numbers, use your VoIP service provider s dialing plan. To receive a call through the device, the other party must have your SIP number and a SIP account of their own. 1. Go to Viewing a Product s Certification(s) 2. Select your product from the drop-down list box on the ZyXEL home page to go to that product's page. 3. Select the certification you wish to view from this page. 12