0.3mm Pitch 1.1mm Height Top and Bottom Contact Back-Flip actuator Flexible Printed Circuit Connectors

Transcription

1 .3mm Pitch 1.1mm Height Top and Bottom Contact Back-Flip actuator Flexible Printed Circuit Connectors FH39 Series 3.45mm Depth 1.1mm Features 1. Low-profile.3mm pitch connector with top and bottom contact Usable via either its top or bottom contact point, this connector achieves enhanced freedom in terms of the product design. 2. High contact reliability thanks to the spring terminal structure Because both top and bottom contact points are spring-loaded, the contact point adapts to the FPC motion, and high contact reliability is ensured. 3. Delivered with the actuator open FPC can be immediately inserted without the need for the opening of the actuator. (Fig.2) 4. Easy FPC insertion Entry chamfers at all sides of the FPC insertion slot assure correct insertion and positioning of the FPC. 5. Accepts standard FPC thickness.2mm thick standard Flexible Printed Circuit (FPC) can be used. This is the only ultra-low profile ZIF connector using standard FPC. 13.9mm(39 pos.) Easy FPC insertion Completely locked Actuator 3.45mm FPC Fig.1 Fig.2 6. Conductive traces on the PCB can run under the connector No exposed contacts on the bottom of the connector. 7. Board placement with automatic equipment Flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. Standard reel packaging contains 5 connectors. Fig.3 8. Halogen-free * (FH39J Series) *As defi ned by IEC Br-9ppm maximum, Cl-9ppm maximum, Cl + Br combined-1,5ppm maximum

2 Product Specifications Current rating.2a Ratings Voltage rating 3Vrms AC Recommended FPC Operating temperature range Operating humidity range -55 to +85 C (Note 1) Relative humidity 9% max. (No condensation) Storage temperature range Storage humidity range Thickness:.2 ±.3mm, Gold plated contact pads -1 to +5 C (Note 2) Relative humidity 9% max. (No condensation) Item Specifi cation Conditions 1.Insulation resistance 5Mø min. 1V DC 2.Withstanding voltage No fl ashover or insulation breakdown 9Vrms AC / 1 minute 3.Contact resistance 4.Durability 5.Vibration 6.Shock 7.Humidity (Steady state) 8.Temperature cycle 9. Resistance to soldering heat Note 1 : Includes temperature rise caused by current fl ow. Note 2 : The term "storage" refers to products stored for a long period prior to mounting and use. The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or during transportation after board mounting. Materials / Finish Part Material Finish Remarks LCP Color : Beige Insulator UL94V- PA Color : Black Contacts Gold plated Phosphor bronze Metal fittings Pure tin reflow plated Product Number Structure 1mø max. 1mA, AC max (AC: 1kHz) * Including FPC and FFC conductor resistance Contact resistance : 1mø max. 1 cycles No electrical discontinuity of 1µs or longer Contact resistance : 1mø max. No electrical discontinuity of 1µs or longer Contact resistance : 1mø max. Contact resistance : 1mø max. Insulation resistance : 5Mø min. Contact resistance : 1mø max. Insulation resistance : 5Mø min. No deformation of components affecting performance Frequency : 1 to 55Hz, single amplitude of.75mm, 1 cycles in each of the 3 axis FH 39 J - 51S -.3 SHW (1) q w e r t y u Acceleration of 981m/s2, 6ms duration, sine half-wave, 3 cycles in each of the 3 axis 96 hours at 4ç and humidity of 9 to 95% Temperature : -55ç +15ç to +35ç +85ç +15ç to +35ç Time : 3 2 to to 3 minutes 5 cycles Refl ow : At the recommended temperature profi le Manual soldering : 35ç ± 5ç for 5 seconds q Series name : FH w Series No. : 39 e Blank : Standard A : Long actuator type J : Halogen-free (Flame retardance UL94V-). r No. of Contacts FH39 : to 61 FH39A : 67 FH39J : to 51 t Contact pitch :.3mm y Termination type SHW... SMT horizontal staggered row mount type u Plating specifi cations (1)...Standard 5, pcs/reel (99)...5 pcs/reel 2

3 Connector Dimensions.3±.1 A±.15 B±.1.6±.1 (.12) (1.85) 3.55±.2 (.42) (FPC : t.2mm) 1 B Detailed drawing [FH39 Series] (3.85) (2.1) (1.55) (.85).1 1 Note 1 : The coplanarity of each terminal lead within specifi ed dimension is.1 mm Max. 2 : Packaged on tape and reel only. Check packaging specifi cation. 3 : Slight variations in color of the plastic compounds do not affect form, fi t or function of the connector. 4 : After refl ow, the terminal plating may change color, however this does not represent a quality issue. Part No. FH39-S-.3SHW(1) FH39-27S-.3SHW(1) FH39-29S-.3SHW(1) FH39-33S-.3SHW(1) FH39-39S-.3SHW(1) FH39-45S-.3SHW(1) FH39-51S-.3SHW(1) FH39-61S-.3SHW(1) FH39A-67S-.3SHW(1) FH39J-S-.3SHW(1) FH39J-33S-.3SHW(1) FH39J-39S-.3SHW(1) FH39J-45S-.3SHW(1) FH39J-51S-.3SHW(1) Production LOT No..6±.1 C±.1 Note 1 : Tape and reel packaging (5, pcs/reel, 5 pcs/reel). Note 2 : Order by number of reels..1 (9 ) 1.1±.1 (1.54) (D) E±.1.47±.1.3±.1.1±.15 3.±.15.1±.15 (.42) (FPC : t.2mm) (.12) (.15) B Detailed drawing [FH39A Series] (4.15) (2.1) (1.55) (.85) All dimensions : mm HRS No. No. of Contacts A B C D E (9 ) (.6) 1.1±.1 (1.89).47±.1.3±.1.1±.15 3.±.15.1± (3.3) B 3

4 BRecommended PCB mounting pattern and metal mask dimensions (3.65) 2-R.2.67± ±.5.5±.5 (Metal mask:.42) (Metal mask:.57).3±.3 (Metal mask:.) B±.5 C±.5.6±.5.3±.5.3±.3.6±.5 (Metal mask:.) B Recommended FPC Dimensions.3±.7 F±.5 C±.3.3± ±.2.3± ±.1 1.5± ±.1.6±.7 B±.3.6±.7 Part No. FH39-S-.3SHW(1) FH39-27S-.3SHW(1) FH39-29S-.3SHW(1) FH39-33S-.3SHW(1) FH39-39S-.3SHW(1) FH39-45S-.3SHW(1) FH39-51S-.3SHW(1) FH39-61S-.3SHW(1) FH39A-67S-.3SHW(1) FH39J-S-.3SHW(1) FH39J-33S-.3SHW(1) FH39J-39S-.3SHW(1) FH39J-45S-.3SHW(1) FH39J-51S-.3SHW(1) ±.2 HRS No. No. of Contacts B Recommended metal mask thickness : t=.1 2.1±.1 2.± ± ±.5 (Metal mask:.35).8±.5 * (1) (Uncovered area) (.1) 3.65MIN (Stiffner) (.2).1±.5 1±.5 (Metal mask:1).2±.3 Note : Stiffener dimension should be 3.65mm min., however if it is not satisfi ed, X dimension should be.5mm or more. C All dimensions : mm F

5 BRecommended FPC construction 1. Using Single-sided FPC FPC : Flexible Printed Circuit Material Name Covering film layer Cover adhesive Surface treatment Copper foil Base adhesive Base film Reinforcement material adhesive Stiffener Polyimide Material 1 mil thick..2µm thick gold plated over 1 to 5µm nickel underplating Cu 1oz Polyimide 1 mil thick Polyimide 3 mil thick Total 2. Using Double-sided FPC FPC : Flexible Printed Circuit Material Thickness(µm) * To prevent release of the FPC due to its bending, use of the double sided FPC with copper foil on the back side is not recommended. 3. Precautions 1 : This specification is a recommendation for the construction of the FH39 Series FPC (t=.2±.3). 2 : For details about the construction, please contact the FPC manufacturers. () () Material Name Material Material Thickness (µm) Covering film layer Polyimide 1 mil thick. () Cover adhesive () Surface treatment Through-hole copper Copper foil Base adhesive.2µm thick gold plated over 1 to 5µm nickel underplating Cu Cu 1/2oz Base film Polyimide 1 mil thick Base adhesive Copper foil Cover adhesive Cu 1/2oz 18 (18) Covering film layer Polyimide 1 mil thick. Reinforcement material adhesive Stiffener Polyimide 3 mil thick Total 197 BPackaging Specification Embossed Carrier Tape Dimensions (Tape width to 24mm max.) (2.1 : FH39 series) (2.4 : FH39A series) (.3) 4±.1 2±.15 8±.1 Ø (K) G± ±.1 J±.1 Flat surface, for placement with automatic equipment. Unreeling direction (4.65) (1.85) 5

6 Embossed Carrier Tape Dimensions (Tape width 32mm min.) Ø J± ±.1 (K) H±.1 G±.3 Reel Dimensions (Ø13) (Ø38) (Ø8) (L : INSIDE) (M : OUTSIDE) All dimensions : mm Part No. HRS No. No. of Contacts G H J K L M FH39-S-.3SHW(1) FH39-27S-.3SHW(1) FH39-29S-.3SHW(1) FH39-33S-.3SHW(1) FH39-39S-.3SHW(1) FH39-45S-.3SHW(1) FH39-51S-.3SHW(1) FH39-61S-.3SHW(1) FH39A-67S-.3SHW(1) FH39J-S-.3SHW(1) FH39J-33S-.3SHW(1) FH39J-39S-.3SHW(1) FH39J-45S-.3SHW(1) FH39J-51S-.3SHW(1)

7 BConnector Operation and Precautions Operation Exercise care when handling connectors. Follow recommendations given below. 1. As delivered Delivered with the actuator open. There is no need to operate the actuator prior to the insertion of the FPC. The actuator is open when delivered in the embossed tape packaging [Note] Do not close the actuator if the FPC has not been inserted yet. If the actuator is closed without the FPC, it can narrow the contact gap and increases the insertion force. 2. FPC insertion Align the FPC perpendicular with the connector and insert it fi rmly all the way. 3. Locking method qoperate the actuator in a rotational manner and press it down. Rotate and push down on the middle portion or the entire width of the actuator using the finger tip. Be sure to distribute the pressure evenly across the actuator, pressing down on only one side of the actuator may damage the actuator. Excessive force on the housing can also lead to damage or malfunction. 4. FPC removal (Lock release) qslowly rotate the actuator in an upward motion. After it is unlocked, the FPC can be removed. wwhen unlocking the actuator, always touch the middle portion of the actuator. Again, be sure to distribute the pressure evenly across the actuator, pressing down on only one side may damage the actuator. The actuator has a maximum opening of 9ç. Trying to open it more than that or applying any unnecessary force to the actuator will cause damage and possibly failure of the connector. Rotate Push at the center of the actuator. Rotate (lift) Lift at the center Excessive force after the actuator is already closed Do NOT close at the ends. Do not attempt to open more than 9 Do not open (lift) at one end. * The actuator opens by rotating it in the direction opposite to the direction of the insertion of the FPC. do not attempt to open it from the same side as the insertion of the FPC. 7

8 Powered by TCPDF ( FH39 Series.3mm Pitch 1.1mm Height Top and Bottom Contact Back-Flip actuator Flexible Printed Circuit Connectors Precautions when mounting connectors on the PCB BTemperature Profile (ç) Temperature PC board warpage Minimize the warpage as much as possible. The connector is straight within.1 mm max. Make sure that the mounting area flatness can accept the connector terminals without causing any failure of the solder joints. Handling before mounting on PCB Do not apply.5n or more external force to the connector before mounting. Insertion of the FPC or operation of the actuator prior to mounting on the PCB is not recommended. Forces on the board When braking the large PC board into individual boards exercise care not to damage the installed connectors. When attaching the boards or other components with the screws make sure that any stresses will not cause board defl ections affecting the mounting areas of the connector. Connector Other precautions When hand soldering: FPC (for mounting connectors) Do not perform hand soldering with the FPC inserted in the connector. Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads. Do not use excessive amount of solder or flux compounds. Operation of the actuator or contacts may be affected by excessive amounts of solder or fl ux compounds ç 2ç MAX ç 23ç HRS test condition Solder method : Refl ow, IR/hot air Environment : Room air Solder composition : Paste, 96.5%Sn/3.%Ag/.5%Cu (Senju Metal Industry, Co., Ltd.'s Part No.:M75-221CM ) Test board : Glass epoxy mm 5mm.8mm thick Land dimensions :.3mm.5mm,.3mm.67mm Metal mask :..42,..57.1mm thick 5 Start ç (6 sec.) 9 sec. to 12 sec. Preheating Time (Seconds) (6 sec.) Soldering The temperature profiles shown are based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume / thickness and board size / thickness. Consult your solder paste and equipment manufacturer for specific recommendations ,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi ,JAPAN TEL: Fax: The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 8/215. Contents are subject to change without notice for the purpose of improvements.