TYLÖ MEGA-LINE SUPER 10 - Electrical Sauna Heater Manual -

Transcription

1 TYLÖ MEGA-LINE SUPER 10 - Electricl Sun Heter Mnul - 1. INTRODUCTION We thnk you for your confidence in this Tylö product. Tylö heters re known to be long lived nd of high qulity. We recommend tht you nd the person instlling this heter red these instructions crefully. This mnul should be lwys close t hnd when needed. Once the instlltion is completed, this mnul should be hnded to the sun's owner or the person responsible for operting it. Before you do nything, you should red this mnul nd py specil ttention to the WARNINGS prt on pge INSTALLATION 2.1. The Heter's Instlltion Loction The mnufcturer's sfe instlltion distnces (tble 3, pge 5) must be dhered to. These distnces re lso given on the heter's dt plte. The ttchment sizes for the wll mountings re shown in picture 1. The wlls next to the heter nd the roof bove it must not be protected with dditionl pneling, s the temperture in the wll mteril my rise to dngerous levels. This heter is not designed to be embedded or instlled in n lcove Attching The Heter to The Wll For esier instlltion the heter is equipped with detchble wll mounting (picture 1b) tht cn be ttched to the wll beforehnd (picture 1). You my use the included ttchment screws for instlltion in wooden wll. A thin pnel bord is not sturdy enough for the ttchment. You should strengthen it from the bckside using bord or plywood. Use het resistnt ttchments (wedge or hmmerset nchors, no plstic plugs) for msonry, brickwork or other stone wlls. The heter is lifted into its plce ccording to pictures 1c, 1d, 1e. Do not lift the heter by its coils or the upper plte of the bck csing. Use the lower rim of the inner csing with support from the upper prt insted. A free corridor should be left t one side of the heter for mintennce work Connection to The Power Grid (mm) DI 10K X (min) 195 Y (min) 260 Y (mx) b 320 The heter's electricl instlltion must be performed by certified electricin. Check the heter's technicl dt prior to connection. The connection to the power grid my only be performed by professionl electricin who is certified ccording to present regultions. The heter is connected semi-permnently to connection box on the sun wll. The connection cord should be H07RN-F (VSN, VSB) rubber cble or equivlent. Do not use cords with PVC insultion. The connection digrm is ttched to this mnul (picture 7) nd to the heter's connection box. Do not ttch the heter's power feed to the error current connector. The connection is performed in the following mnner before the heter is lifted into its plce: 1. Remove the wll mounting in the bck of the heter, open the upper ttchment screws t the sides nd loosen the lower ones. 2. Attch the throughput rubbers nd cble grip. 3. Pss the cble through the throughput rubber to the connection box. 4. Attch the cble to the cble grip nd connector ccording to the connection digrm. 5. Provide sufficient cble length to ensure tht the cble does not run underneth the stone enclosure nor too close to the heter's bse plte. The heter's connector lso provides for control of the electric heting (or the heter's signl lmp). The pckge holds second throughput rubber nd cble grip with screws for this purpose. The control cble's conducting mteril nd dimeter must be equl to the connection cble. The rely used in controlling the electric heting gets control voltge of 230 VAC from the heter. The conductors' dimeters nd numbers nd fuse vlues re given in the technicl dt tble. The spry wter tight connection box must not be ttched more thn 50 cm bove the ground. KASTOR OY TYLÖ MEGA LINE SUPER 10 Sivu 6/22

2 2.4. Instlltion of The Sensor And Its Loction on The Wll The sensor is ttched to the sun wll on the heter's center line. If you wish to het the sun to higher tempertures thn usul, the sensor my be moved to the side ccording to tble 1 nd picture 2. Devitions from the given mesurements will cuse fire hzrds. TABLE 1 HEATER MODEL Super DI 10K 10kW FROM HEATER CENTER C =cm A =cm cm ABOVE FLOOR Min. 80 Min Picture 2 There re two lterntives for ttching the sensor to the wll. For surfce ttchment, the sensor's protective cover is ttched to the sun wll (picture 3A). Attch the sensor to the cover nd rise the cble grip strips t the lower prt of the cover. Bend the cble grip strips round the cble nd bend the wings of the cover over the sensor (picture 3B). For embedded instlltion, the sensor is ttched directly to the wll (picture 3C). Picture Chnging The Loction of The Control Pnel The heter control pnel's loction my only be switched by professionl with sufficient trining. The control pnel hs been fctory instlled to be used from the front of the heter. It my be turned to point to the side of the heter in the following mnner: 1) Relese the ttchment screw underneth the control pnel. 2) Move the rubber gskets on the decortive piping further wy from the control pnel. 3) Remove the control pnel by pulling it outwrds from the piping (the plstic mteril used tolertes bending well). 4) The keybord connector cble in the connection room hs some slck to llow pulling the control pnel further from the piping. 5) Detch the cble t the keybord's row connector. 6) Move the cble to the required side nd pull it through. 7) Assemble in reverse order. 3 SAUNA ROOM INSTRUCTIONS 3.1. The Sun Room The het insultion of wlls nd ceiling must be sufficient, to void losing too much het to the outside. Wood is the most suitble surfce mteril A wooden surfce wrms up quickly nd rdites plesntly even het to the bther's skin. You should void msonry nd other stone surfces in the wlls, s stone tkes in too much het nd would require significntly more powerful heter thn wooden room of the sme size. One squre meter of stone surfce on the wll or ceiling bove the heter's level is equl to 2-3 cubic meters of dditionl volume in the room. A glss door nd windows hve similr effects on the sizing. Log wlls require n b dditionl 25% of dded power to the volume clculted in this mnner. Excessive height lso dds unnecessry volume to the room. The distnce between the highest bench nd the ceiling should not be too high, s the temperture decreses towrds the floor. Picture 4 KASTOR OY TYLÖ MEGA LINE SUPER 10 Sivu 7/22 Min 500 c f

3 A sufficient distnce from bench to ceiling is bout cm. We recommend locting the heter s low s possible (within sfety limits). The sizes of sun rooms re given in tble Correct Air Circultion Sufficient ir exchnge in the sun is very importnt. A suitble mount for fmily sun would be bout 6 times the sun's volume per hour. Air removl hppens either through grvity (= trditionl, nturl circultion ) or mechniclly, through n ir removl fn. Mechnicl ir circultion (pictures 4 nd 5): Fresh ir is tken in (preferbly from outside the house) through 100 mm dimeter pipe tht is t lest 500 mm bove the heter (). The fresh ir my lso be piped in Picture 5 below the heter, close to the floor (b), s long s you mke sure tht the cool ir flow does not go stright long the floor to the exit ir vent. The most importnt spect in ir circultion is to ensure n efficient mixing of fresh ir with heted ir nd the vpor from the thrown wter. The exit ir vent should be preferbly plced below the benches (c), s fr from the ir intke s possible. The exit ir my lso be fed through the wshing room, e.g. underneth the door (e). The sun should lso hve drying vlve (f) behind the benches, ner the ceiling. The drying vlve is closed during the heting nd bthing phses nd opened for the finl drying out. The circultion fn is kept running throughout the bthing nd fterwrds. It my be stopped for the preheting phse. Grvity circultion i.e. nturl circultion (picture 6): Fresh ir is tken in (preferbly from outside the house) through 100 mm dimeter pipe, preferbly from underneth the heter or its immedite vicinity close to the floor (b) or, Picture6 lterntively, bove the heter (). The most importnt spect in ir circultion is to ensure n efficient mixing of fresh ir with heted ir nd the vpor from the thrown wter. The exit ir is fed out preferbly from underneth the benches (d). Drying vlve ner the ceiling (f). The exit ir vent should be plced s fr from the fresh ir intke s possible. The exit ir my lso be fed through the wshing room, e.g. underneth the door (e). The exit ir vent my be closed during preheting. The exit ir vent must be lrger tht the intke nd be locted higher up. Min 500 b b e f d e 4. USE AND MAINTENANCE OF THE HEATER WARNINGS: The Tylö heter is intended for heting fmily sun to norml sun tempertures, nd it must not be used for ny other purpose. The sun room must be checked before the heter is switched on. Bewre the hot heter, s its stones nd metl prts my scld your skin t operting tempertures. Cre is mndted in the heter's vicinity s well prticulrly due to the dnger of slipping. During wter throwing, you should wtch the hot drops sprying from the stones nd the hot stem. Prents must wtch smll children in the sun nd mke sure instructions re heeded. The heter's controls must not be touched immeditely fter wter throwing (becuse of the hot stem rising from it). You must not throw too much wter on the heter t single throw to prevent dngers from excessive mounts of stem. The heter must not be covered nd it must not be used without stones. Unhindered ir flow must be ensured prticulrly behind the heter. You my not hng inflmmble objects such s clothes or crpets bove or ner the heter, s tht is fire hzrd. This heter hs not been designed for use with se wter. Only one heter my be instlled in ny single sun room. Check tht the heter is ttched properly before heting it. fter the heting period, mke sure tht the heter's timer hs turned off the electricity t the set time. If you hve ny problems or questions during the wrrnty period, plese contct the mnufcturer before performing ny repirs. Use gloves during mintennce nd clening work to protect your hnds. Remove ny unnecessry stickers nd plstic pckging prior to first use! 4.1. The Heter Stones The heter must not be used without heter stones. We recommend the use of trditionl qurried heter stones (e.g. peridotite or olivine). A suitble stone size for electric sun heters is 5-10 cm. If you wnt moist nd long lsting results from wter throw, you my use few sop stones in the mix. These go to the bottom of the stone bsket. The stones must be wshed with brush before they re put into plce. You should check the condition of the stones t lest twice yer. Grvel dropping from the stone bsket is sign of brding stones. The heter is not fire hzrd if used without stones or insufficiently filled, but it hs not been designed to run continuously like tht Filling The Stone Bsket The innermost prt of the stone bsket should be filled with bigger stones, right up to the surfce lyer. Use smller stones t the upper prt, going towrds the edges. Tke cre tht no stones fll through the supports onto the heting coils, s the impct my destroy the coils before their time. The stones must not rise more thn 1 cm bove the edge of the heter. If the upper stones remin often wet, you hve too mny stones or they re too smll. KASTOR OY TYLÖ MEGA LINE SUPER 10 Sivu 8/22

4 4.3. First Heting The first heting is performed t mximum temperture with good ventiltion. This burns ny contmintions off the stones nd the coils, which my produce some smoke The Sun's Preheting Phse The preheting phse mens the time needed for heting the sun room to the desired bthing temperture. The time required depends on the desired temperture (position of temperture switch), the mount of stones in the heter, the room's volume nd surfce mteril. The fewer stones you use, the quicker the room hets up, but smller mount of stones gives less stisfying stem output. The preheting phse lsts usully between 40 nd 70 minutes Using The Heter The heter is used from its control pnel. Functions 1 = indictors, 2 = preset timer setting, 3 = temperture setting, 4 = electricity switch, 5 = electricity cut-off Temperture Setting (Perform t ON Setting) Press TEMP the previous temperture setting is shown. The numbers describe rising temperture scle. Try by yourself which temperture setting suits you best. You might strt out with setting of 4, for instnce. Afterwrds you cn rise or lower it until you find your own idel bthing temperture Mnul Strt/Stop Press ON to cut in electricity (the signl light turns on). Press OFF to cut off electricity (the signl lmp turns off). The heter's memory chooses utomticlly the previously used temperture setting. Press TEMP, if you wnt to lter the temperture setting. The timer will utomticlly turn off the electricity to the heter fter three hours. Press OFF to switch it off before tht, nd ON to continue bthing pst these three hours Setting The Preset Timer (Use in OFF Position) In this cse, the numbers show the preset time (= in how mny hours from now the heter will strt heting up). Set the preset timer in the following mnner: Press TIME Type in your desired preset time (1-10 hours). Press ON The preset time is ctivted nd the signl light blinks t the chosen hour setting. Once the heting current hs engged fter the preset time hs run out, the heter will run for three hours nd then cut off utomticlly. You my lso turn off the het prior to tht by pressing OFF. If you wnt to continue bthing pst those three hours, press ON Min Switch Beneth the connection box, next to the throughput of the connection cble, is the min switch. The min switch is only used when the sun is not expected to be in use for long time. The control pnel memory is clered when the current is cut off t the min switch Overheting Protector The heter is equipped with n overheting protector (THERM). It prevents overheting in cses where the temperture regultor mlfunctions. The overheting protector's reset switch is behind the heter. Use long screwdriver or similr for resetting this switch. Prior to resetting, you must investigte the reson for the mlfunction Mintennce The electricl systems of the heter my only be mintined by professionl electricin! When prts re replced, only uthorized components defined by the mnufcturer my be used. If you hve ny problems or questions during the wrrnty period, plese contct the mnufcturer before performing repirs. You my chnge the stones nd clen the heter's exterior by yourself. The heter's cover is clened using mild dish wshing liquid nd soft clening implements dry fter clening. Use gloves to protect your hnds during mintennce nd clening work. 5. OPTIONAL EQUIPMENT (Only implemented by the instller!) 5.1. Electric Heting by Turns At the heter's connection element, connectors 5 nd 6 re reserved for controlling electric heting. Connector 6 gives off steering voltge of 230 VAC whenever the coils re engged. The heter's turnwise heting control permits the other heters in the house to engge when the timer is t zero, on preset time or when the temperture control turns off the heting coils. KASTOR OY TYLÖ MEGA LINE SUPER 10 Sivu 9/22

5 5.2. Externl Signl Light The signl light my be connected to connectors 5 nd 6. It must be noted tht the light does not indicte the stte of the timer switch, but only whether the heting coils re ctive. 6. TECHNICAL DATA (tble 2) Heter Heter Sun room volume Weight Amount Heter size Model output Min Mx without of stones width depth height stones (Mx) SUPER 10 kw m3 m3 kg kg Mm mm mm DI 10 K 10,00 8,0 15, Ø FUSES, RESISTANCE COILS AND CABLES (tble 3) Heter Heter Fuse Instlltion size Voltge Number of heting coils Model output size 1600W 1700W 2000W 400 V 3N~ Group Group Group SUPER 10 kw A mm2 V DI 10 K 10,00 3x16 5x2,5 400V 3N~ SAFE DISTANCES (tble 4) 9. CIRCUIT DIAGRAM (picture 7) Heter Model Sun Sfe distnces for heter (Min) height From side to From front From front to ceiling to floor (Min) wll to upper to lower bench bench B C D E SUPER 10 mm mm mm mm mm mm DI 10 K SAFE DISTANCES (picture 6) MANUFACTURER: KASTOR OY Tehtnktu 5 7 FIN RIIHIMÄKI, FINLAND tel Fx KASTOR OY TYLÖ MEGA LINE SUPER 10 Sivu 10/22