SURFACE OF MATTRESS MUST BE AT LEAST 5 IN. (127 MM) BELOW THE UPPER EDGE OF GUARDRAILS

Transcription

1 Form# sw tm MODERN CHILDREN S FURNITURE UFFIZI BUNK BED Model no. sw-1800 Thank you for your recent purchase of rgington s Uffizi bunk bed. Please read carefully below. You will find extremely important information regarding your child s safety, assembly, maintenance, and other information. Should you need to contact rgington for any reason, you may do so through our website, WRNING! FILURE TO FOLLOW THESE WRNINGS ND THE SSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DETH. FOLLOW THE INFORMTION ON THE WRNINGS PPERING ON THE UPPER BUNK END STRUCTURE ND ON THE CRTON. DO NOT REMOVE WRNING LBEL FROM BED. RED LL INSTRUCTIONS BEFORE SSEMBLING BUNK BED. KEEP INSTRUCTIONS FOR FUTURE USE ND REFERENCE. NY MTTRESS USED WITH THIS BUNK BED SHOULD BE STNDRD SIZED TWIN MTTRESS (39IN X 75IN) WITH THICKNESS NOT EXCEEDING 8 INCHES. LWYS USE THE RECOMMENDED SIZE MTTRESS OR MTTRESS SUPPORT, OR BOTH, TO HELP PREVENT THE LIKELIHOOD OF ENTRPMENT OR FLLS SURFCE OF MTTRESS MUST BE T LEST 5 IN. (127 MM) BELOW THE UPPER EDGE OF GURDRILS DO NOT LLOW CHILDREN UNDER 6 YERS OF GE TO USE THE UPPER BUNK PERIODICLLY CHECK ND ENSURE THT THE GURDRIL, LDDER, ND OTHER COMPONENTS RE IN THEIR PROPER POSITION, FREE FROM DMGE, ND THT LL CONNECTORS RE TIGHT DO NOT LLOW HORSEPLY ON OR UNDER THE BED ND PROHIBIT JUMPING ON THE BED LWYS USE THE LDDER FOR ENTERING ND LEVING THE UPPER BUNK USE OF NIGHT LIGHT MY PROVIDE DDED SFETY PRECUTION FOR CHILD USING THE UPPER BUNK. DO NOT PLCE THE BED NER WINDOW WHERE CORDS FROM BLINDS OR DRPES MY STRNGLE CHILD. DO NOT SUBSTITUTE PRTS. CONTCT THE MNUFCTURER OR DELER FOR REPLCEMENT PRTS - rgington, Inc, 661 Meeker ve, Brooklyn, NY 11222, info@argington.com, IF REFINISHING, USE NON-TOXIC FINISH SPECIFIED FOR CHILDREN S PRODUCTS. LWYS USE GURD RILS ON BOTH LONG SIDES OF THE UPPER BUNK. IF THE BUNK BED WILL BE PLCED NEXT TO THE WLL, THE GURDRIL THT RUNS THE FULL LENGTH OF THE BED SHOULD BE PLCED GINST THE WLL TO PREVENT ENTRPMENT BETWEEN THE BED ND WLL. THE USE OF WTER OR SLEEP FLOTTION MTTRESSES IS PROHIBITED. 1

2 LIST OF PRTS HEDBORD X 1 BRCES X 4 VERTICL SUPPORTS RIGHT SUPPORT PNEL X 1 LEFT SUPPORT PNEL X 1 LDDER X 1 RIGHT SIDE FRME X 1 END PNEL X 2 LEFT SIDE FRME X 1 UX END PNEL X 2 SLT X 4 LOWER BUNK FRME END PNEL X 2 RIGHT SIDE FRME X 1 GURD RIL X 2 LEFT SIDE FRME X 1 UPPER BUNK FRME SLT X 4 LOFT SUPPORT X 1 DESK TTCHMENT X 1 PLINTH X 1 CCESSORIES B HRDWRE LLEN KEY X 1 BOLT X 56 (30mm / 1-1/8 ) BOLT B X 4 (45mm / 2 )

3 PLESE NOTE: YOUR BUNK BED WILL SHIP IN FIVE SEPERTE BOXES, SW1800, SW1801, SW1802, SW1803, ND SW1804. BEFORE YOU BEGIN SSEMBLY, MKE SURE THT LL PRTS RE PRESENT. DDITIONLLY, PLESE MKE SURE NOT TO OVERTIGHTEN NY BOLT. THIS COULD CUSE DMGE TO THE BUNK BED. CREFULLY PLCE LL SSEMBLY HRDWRE IN BOX OR OTHER CONTINER TO PREVENT LOSING PRTS WHILE SSEMBLING. SSEMBLE THE FURNITURE ON THE CRTON OR CRPET IN ORDER TO PROTECT THE FURNITURE FINISH ND YOUR FLOOR. TO CLEN THE BED, WIPE WITH MOIST SOFT COTTON CLOTH. USE ONLY WTER. DO NOT USE BRSIVES SSEMBLY: 1 BEGIN THE SSEMBLY BY TTCHING THE SUPPORT BRCES TO THE VERTICL SUPPORTS S SHOWN BOVE USING THE SCREWS. PLESE NOTE THT WHEN INSTLLING THE TWO BOTTOM BRCES, THERE SHOULD BE TWO HOLES / THREDED INSERTS FCING UPWRDS FOR ECH SUPPORT. SEE DETIL BOVE.

4 2 NOTE: WHEN INSTLLING THESE PRTS, MKE SURE THERE IS HOLE IN THE END S SHOWN NEXT, TTCH THE LEFT ND RIGHT LOWER BUNK SIDES S SHOWN USING THE BOLTS. 3 TTCH THE END PNELS S SHOWN BOVE USING THE BOLTS. THE BED FRME MY PIVOT S IT IS ONLY CONNECTED T TWO POINTS, SO THIS IS COMPLETELY NORML.

5 4 TTCH THE FRME NOW TO THE HOLES LOCTED ON THE INNER LIP OF THE HEDBORD USING THE BOLTS. 5 B B USING THE BOLTS, TTCH THE RIGHT HND SIDE OF THE UPPER BED FRME TO THE RIGHT SUPPORT IN THE LOWER SET OF HOLES S SHOWN BOVE. THEN, USING THE B BOLTS, TTCH THE BED FRME FROM THE TOP TO THE HEDBORD. REPET THESE STEPS FOR THE RIGHT HND SIDE UPPER BED FRME S WELL.

6 6 USING THE BOLTS, TTCH THE UPPER BED FRME END PNELS. THEN TTCH THE GURD RILS TO THE SUPPORTS ND END PNELS S SHOWN. 7 FINLLY, DROP THE BED SLTS IN THE BED FRMES ND HOOK THE LDDER ON TO NY ONE OF THE FOUR SIDES OF THE UPPER BED FRME S SHOWN. PLESE NOTE THT ON THE UPPER BED FRME, THE MTTRESS YOU USE SHOULD NOT EXCEED THICKNESS OF 8 INCHES.

7 SETTING UP THE LOWER BUNK IN THE LTERNTE POSITION. 1 IF YOU WOULD LIKE TO SET UP THE LOWER BUNK IN N LTERNTE POSITION, STRT BY RETTCHING THE LEFT ND RIGHT HND SIDE LOWER BUNK FRMES S SHOWN BOVE. IF YOU HVE LREDY SSEMBLED THE FRME, SIMPLY REMOVE IT FROM THE SUPPORTS ND HEDBORD, ROTTE IT 90 DEGREES ND RETTCH. 2 THEN, USING THE BOLTS, TTCH THE HED PNEL OF THE LOWER BUNK FRME ND TTCH THE UX END PNEL T THE FOOT OF THE FRME S SHOWN BOVE. ONCE THIS STEP IS COMPLETE, PLCE SLTS IN LOWER BUNK ND IT IS REDY FOR USE. IMPORTNT: MKE SURE TO USE THE UX END PNEL DURING THIS STEP. IN THIS NEW POSI- TION, THE LOWER BUNK MUST HVE DDITIONL SUPPORT T THE FOOT OF THE BED THT IS PROVIDED BY THE UX END PNEL

8 3 THE LST STEP IS TO TTCH THE FOOT PLINTH TO THE NOW EXPOSED LOWER BRCES BETWEEN THE VERTICL SUPPORTS. LOWER THE PLINTH INTO PLCE S SHOWN BOVE ND TTCH USING BOLTS. SETTING UP THE BED S LOFT BED WITH DESK TO USE THE BED S LOFT, REMOVE THE LOWER BUNK LTOGETHER, ND REPLCE WITH THE LOFT SUPPORT PIECE S SHOWN IN THE DIGRM TO THE RIGHT. TTCH WITH BOLTS. THE DESK TTCHMENT SLIDES INTO POSITION THROUGH THE WINDOW ND LOWERS DIRECTLY ONTO THE PNELS OF THE SUPPORTS S SHOWN. NO HRDWRE TTCHMENT IS NECESSRY DESK SIMPLY LOWERS DIRECTLY ONTO THE PNELS OF THE SUPPORTS

9 SETTING UP THE LOWER BUNK S DETCHED TWIN BED With the Uffizi bunk bed set up as a loft, you may choose to set up the lower bunk away from the main assembly. Use (8) bolts and additional aux end panels found in box 4 to complete assembly as shown below. Use provided allen key to tighten all bolts firmly.