Operation Guide

Transcription

1 MO1405-EB EGLISH Congratuations upon your seection of this CASIO watch. E-1 Warning! The measurement functions buit into this watch are not intended for taking measurements that require professiona or industria precision. Vaues produced by this watch shoud be considered as reasonabe representations ony. The Moon phase indicator that appears on the dispay of this watch is not intended for navigation purposes. Aways use proper instruments and resources to obtain data for navigation purposes. When engaging in mountain cimbing or other activities in which osing your way can create a dangerous or ife-threatening situation, aways use a second compass to confirm direction readings. that CASIO COMPUTER CO., LTD. assumes no responsibiity for any damage or oss suffered by you or any third party arising through the use of this product or its mafunction. About This Manua Depending on the mode of your watch, dispay text appears either as dark figures on a ight background (Modue 3261), or ight figures on a dark background (Modue 3281). A of the iustrations in this manua show Modue Button operations are indicated using the etters shown in the iustration. that the product iustrations in this manua are intended for reference ony, and so the actua product may appear somewhat different than depicted by an iustration. Modue 3261 Modue 3281 E-2 E-3 Things to check before using the watch 1. Check the battery power eve. Is H or M dispayed for the battery power indicator (page E-14)? O Does any one of the foowing conditions exist? Battery power indicator shows L and LOW is dispayed in the upper right corner of the screen. CHG is dispayed in the upper right corner of the screen. The face is bank. YES Power is ow. Charge the watch by pacing it in a ocation where it is exposed to ight. For detais, see Charging the Watch (page E-12). E-4 Battery power indicator YES The watch is charged sufficienty. For detais about charging, see Charging the Watch (page E-12). Go to step 2. EXT 2. Check the Home and the dayight saving time (DST) setting. Use the procedure under To configure Home settings (page E-26) to configure your Home and dayight saving time settings. Word Time Mode data depend on correct Home, time, and date settings in the Timekeeping Mode. Make sure you configure these settings correcty. 3. Set the current time. See Configuring Current Time and Date Settings (page E-29). The watch is now ready for use. E-5 Contents E-3 About This Manua E-4 Things to check before using the watch E-12 Charging the Watch E-19 To recover from the seep state E-20 To turn Power Saving on and off E-21 Mode Reference Guide E-25 Timekeeping E-26 Configuring Home Settings E-26 To configure Home settings E-28 To change the Dayight Saving Time (summer time) setting E-29 Configuring Current Time and Date Settings E-29 To change the current time and date settings E-33 Digita Compass E-34 To take a digita compass reading E-40 To perform magnetic decination correction E-42 To perform bidirectiona caibration E-43 To perform northery caibration E-46 To store a direction ange reading in Bearing Memory E-48 To set a map and find your current ocation E-50 To find the bearing to an objective E-52 To determine the direction ange to an objective on a map and head in that direction E-6 E-7 E-57 Thermometer E-57 To enter and exit the Digita Compass/Thermometer Mode E-59 To caibrate the temperature sensor E-61 Specifying Temperature Unit E-61 To specify temperature unit E-63 Temperature Reading Precautions E-64 Using the Moon Data E-64 To enter the Moon Data Mode E-67 To reverse the dispayed Moon phase E-71 Checking the Current Time in a Different Time Zone E-71 To enter the Word Time Mode E-72 To view the time in another time zone E-72 To specify standard time or dayight saving time (DST) for a city E-74 Using the Stopwatch E-74 To enter the Stopwatch Mode E-74 To perform an eapsed time operation E-75 To pause at a spit time E-75 To measure two finishes E-77 Using the Countdown Timer E-77 To enter the Countdown Timer Mode E-78 To specify the countdown start time E-79 To perform a countdown timer operation E-79 To stop the aarm E-8 E-9

2 E-80 Using the Aarm E-80 To enter the Aarm Mode E-81 To set an aarm time E-82 To test the aarm E-82 To turn an aarm and the Houry Time Signa on and off E-83 To stop the aarm E-84 Iumination E-84 To turn on iumination manuay E-85 To change the iumination duration E-88 To turn the auto ight switch on and off E-91 Graphic Area E-92 Button Operation Tone E-93 To turn the button operation tone on and off E-94 Troubeshooting E-99 Specifications E-10 E-11 Charging the Watch The face of the watch is a soar ce that generates power from ight. The generated power charges a buit-in rechargeabe battery, which powers watch operations. The watch charges whenever it is exposed to ight. Charging Guide Whenever you are not wearing the watch, eave it in a ocation where it is exposed to ight. Best charging performance is achieved by exposing the watch to the strongest ight avaiabe. E-12 When wearing the watch, make sure that its face is not bocked from ight by the seeve of your cothing. The watch may enter a seep state (page E-18) if its face is bocked by your seeve even ony partiay. Warning! Leaving the watch in bright ight for charging can cause it to become quite hot. Take care when handing the watch to avoid burn injury. The watch can become particuary hot when exposed to the foowing conditions for ong periods. On the dashboard of a car parked in direct sunight Too cose to an incandescent amp Under direct sunight Aowing the watch to become very hot can cause its iquid crysta dispay to back out. The appearance of the LCD shoud become norma again when the watch returns to a ower temperature. Turn on the watch s Power Saving function (page E-18) and keep it in an area normay exposed to bright ight when storing it for ong periods. This heps to ensure that power does not run down. Storing the watch for ong periods in an area where there is no ight or wearing it in such a way that it is bocked from exposure to ight can cause power to run down. Expose the watch to bright ight whenever possibe. E-13 Power Leves You can get an idea of the watch s power eve by observing the battery power indicator on the E-14 Battery power indicator Leve 1 (H) 2 (M) 3 (L) 4 (C) Battery Power Indicator Function Status A functions enabed. A functions enabed. Iumination, beeper, and sensor operation disabed. Except for the CHG (charge) indicator, a functions and dispay indicators disabed. 5 A functions disabed. The fashing LOW indicator at Leve 3 (L) tes you that battery power is very ow, and that exposure to bright ight for charging is required as soon as possibe. At Leve 4 or Leve 5, a functions are disabed and settings return to their initia factory defauts. Once the battery reaches Leve 2 (M) after faing to Leve 4 or Leve 5, reconfigure the current time, date, and other settings. If charging starts from Leve 5, CHG wi start fashing on the dispay when Leve 4 is reached., however, that watch functions are not restored at this time. Leave the watch exposed to sufficienty strong ight unti the battery eve reaches Leve 2 or Leve 1 before using it. Leaving the watch exposed to direct sunight or some other very strong ight source can cause the battery power indicator to show a reading temporariy that is higher than the actua battery eve. The correct battery eve shoud be indicated after a few minutes. A data stored in memory is deeted, and the current time and a other settings return to their initia factory defauts whenever battery power drops to Leve 4 or Leve 5, and when you have the battery repaced. E-15 Power Recovery Mode Performing mutipe sensor, iumination, or beeper operations during a short period may cause a of the battery power indicators (H, M, and L) to start fashing on the This indicates that the watch is in the power recovery mode. Iumination, aarm, countdown timer aarm, houry time signa, and sensor operations wi be disabed unti battery power recovers. Battery power wi recover in about 15 minutes. At this time, the battery power indicators (H, M, L) wi stop fashing. This indicates that the functions isted above are enabed again. If a of the battery power indicators (H, M, L) are fashing and the CHG (charge) indicator aso is fashing, it means the battery eve is very ow. Expose the watch to bright ight as soon as possibe. Even if battery power is at Leve 1 (H) or Leve 2 (M), the Digita Compass/ Thermometer Mode sensor may be disabed if there is not enough votage avaiabe to power it sufficienty. This is indicated when a of the battery power indicators (H, M, L) are fashing. Frequent fashing of a of the battery power indicators (H, M, L) probaby means that remaining battery power is ow. Leave the watch in bright ight to aow it to charge. E-16 Charging Times Exposure Leve (Brightness) Outdoor sunight (50,000 ux) Sunight through a window (10,000 ux) Dayight through a window on a coudy day (5,000 ux) Indoor fuorescent ighting (500 ux) Daiy Operation *1 Leve Change *2 Leve 5 Leve 4 Leve 3 Leve 2 Leve 1 5 min. 2 hours 16 hours 5 hours 24 min. 6 hours 79 hours 21 hours 48 min. 12 hours 159 hours 43 hours 8 hours 168 hours *1 Approximate amount of exposure time required each day to generate enough power for norma daiy operation. *2 Approximate amount of exposure time (in hours) required to take power from one eve to the next. E-17 The above exposure times a are for reference ony. Actua exposure times depend on ighting conditions. For detais about the operating time and daiy operating conditions, see the Power Suppy section of the Specifications (page E-101). Power Saving When turned on, Power Saving enters a seep state automaticay whenever the watch is eft for a certain period in an area where it is dark. The tabe beow shows how watch functions are affected by Power Saving. There actuay are two seep state eves: dispay seep and function seep. Eapsed Time in Dark Dispay Operation 60 to 70 minutes (dispay seep) 6 or 7 days (function seep) Bank, with PS fashing Bank, with PS not fashing Dispay is off, but a functions are enabed. A functions are disabed, but timekeeping is maintained. The watch wi not enter a seep state between 6:00 AM and 9:59 PM. If the watch is aready in a seep state when 6:00 AM arrives, however, it wi remain in the seep state. The watch wi not enter a seep state whie it is in the Stopwatch Mode or Countdown Timer Mode. To recover from the seep state Move the watch to a we-it area, press any button, or ange the watch towards your face for reading (page E-86). E-18 E-19

3 To turn Power Saving on and off 1. In the Timekeeping Mode, hod down A unti SET Power saving starts to fash and the city name starts to scro on the on indicator 2. Use D to dispay the Power Saving On/Off screen shown nearby. 3. Press E to togge Power Saving on (On) and off (OFF). 4. Press A to exit the setting screen. The Power Saving on indicator (PS) is on the dispay in a modes whie Power Saving is turned on. Mode Reference Guide Your watch has 7 modes. The mode you shoud seect depends on what you want to do. To do this: Enter this mode: See: View the current date in the Home Configure Home and dayight saving time (DST) settings Configure time and date settings Timekeeping Mode E-25 Determine your current bearing or the direction from your current Digita Compass/ ocation to a destination as a direction indicator and ange vaue Thermometer Mode Determine your current ocation using the watch and a map E-33 View the temperature at your current ocation Digita Compass/ Thermometer Mode E-57 View the current time in one of 48 cities (31 time zones) around the gobe Word Time Mode E-71 Use the stopwatch to measure eapsed time Stopwatch Mode E-74 Use the countdown timer Countdown Timer Mode E-77 Set an aarm time Aarm Mode E-80 E-20 E-21 Seecting a Mode Word Time Mode Moon Data Mode Timekeeping Mode The iustration beow shows which buttons you need to press to navigate between modes. Press D to change from mode to mode. Hod down D for about two seconds to return to the Timekeeping Mode from any other mode. In any mode, press C to enter the Digita Compass/Thermometer Mode. Press D in the Digita Compass/Thermometer Mode to return to the mode you entered from. In any mode (except when a setting screen is on the dispay), press B to iuminate the Stopwatch Mode Countdown Timer Mode Aarm Mode Press Press Digita Compass/ Thermometer Mode E-22 E-23 Genera Functions (A Modes) The functions and operations described in this section can be used in a of the modes. Auto Return Features The watch returns to the Timekeeping Mode automaticay if you do not perform any button operation for two or three minutes in the Aarm, or Moon Data Mode. If you eave a screen with fashing digits on the dispay for two or three minutes without performing any operation, the watch exits the setting screen automaticay. Initia Screens When you enter the Word Time or Aarm Mode, the data you were viewing when you ast exited the mode appears first. Scroing The E and B buttons are used on the setting screen to scro through data on the In most cases, hoding down these buttons during a scro operation scros through the data at high speed. Timekeeping Use the Timekeeping Mode to set and view the current time and date. Press A to togge between the day of the week and date (Date screen), and the currenty seected Word Time (Dua Time). Date Screen Dua Time Screen Day of week PM indicator Month Day Hour : Minutes Seconds Dua time E-24 E-25 Configuring Home Settings name E-26 Hour : Minutes PM indicator Seconds There are two Home settings: actuay seecting the Home and seecting either standard time or dayight saving time (DST). To configure Home settings 1. In the Timekeeping Mode, hod down A unti SET starts to fash and the city name starts to scro on the The watch wi exit the setting mode automaticay if you do not perform any operation for about two or three minutes. For detais about city names, see the Code Tabe at the back of this manua. 2. Press E (East) and B (West) to seect the city name you want to use as your Home. Keep pressing E or B unti the city name you want to seect as your Home appears on the 3. Press D to dispay the DST setting screen. 4. Use E to togge the DST settings between OFF and On. that you cannot switch between standard time and dayight saving time (DST) whie UTC is seected as your Home. 5. After a the settings are the way you want, press A to return to the Timekeeping Mode. The DST indicator appears to indicate that Dayight Saving Time is turned on. After you specify a city name, the watch wi use UTC* offsets in the Word Time Mode to cacuate the current time for other time zones based on the current time in your Home. * Coordinated Universa Time, the word-wide scientific standard of timekeeping. The reference point for UTC is Greenwich, Engand. E-27 To change the Dayight Saving Time (summer time) setting 1. In the Timekeeping Mode, hod down A unti SET starts to fash and the city name starts to scro on the 2. Press D to dispay the DST setting screen. 3. Use E to togge the DST settings between OFF and On. 4. After a the settings are the way you want, press A to return to the Timekeeping Mode. The DST indicator appears to indicate that Dayight Saving Time is turned on. Configuring Current Time and Date Settings You can use the procedure beow to adjust the Timekeeping Mode time and date settings if they are off. To change the current time and date settings 1. In the Timekeeping Mode, hod down A unti SET name starts to fash and the city name starts to scro on the 2. Use E and B to seect the city name you want. Seect your Home name before changing any other setting. Hour : Minutes For fu information on city names, see the PM indicator Seconds Code Tabe at the back of this manua. E-28 E-29

4 SE E 3. Press D to move the fashing in the sequence shown beow to seect the other settings. ame Thermometer unit E-30 DST 12/24-Hour Format Power Saving Iumination Duration Seconds Hour Minutes Year Button Operation Tone On/Off Day Month The foowing steps expain how to configure timekeeping settings ony. 4. When the timekeeping setting you want to change is fashing, use E and/or B to change it as described beow. Screen To do this: Do this: Change the city name Togge between Dayight Saving Time (On) and Standard Time (OFF). Use E (East) and B (West). Press E. Screen To do this: Do this: Togge between 12-hour (12H) and 24-hour (24H) timekeeping. Press E. 50 Reset the seconds to 00 Press E. Change the hour or minutes Change the year, month, or day Use E (+) and B ( ). 5. Press A to exit the setting screen. For information about seecting a Home and configuring the DST setting, see Configuring Home Settings (page E-26). E-31 Whie 12-hour format is seected for timekeeping, a P (PM) indicator wi appear for times from noon to 11:59 p.m. o indicator appears for times from midnight to 11:59 a.m. With 24-hour format, time is dispayed from 0:00 to 23:59, without any P (PM) indicator. The watch s buit-in fu automatic caendar makes aowances for different month engths and eap years. Once you set the date, there shoud be no reason to change it except after you have the watch s rechargeabe battery repaced or after power drops to Leve 5 (page E-14). Digita Compass A buit-in bearing sensor detects magnetic north at reguar intervas and indicates one of 16 directions on the The watch aso takes temperature readings in the Digita Compass/Thermometer Mode. For more information, see Thermometer (page E-57). E-32 E-33 To take a digita compass reading Temperature 1. Pace the watch on a fat surface. If you are wearing 12 o cock the watch, make sure that your wrist is horizonta (in position orth reation to the horizon). Direction pointer indicator 2. Point the 12 o cock position of the watch in the direction you want to check. 3. Press C to enter the Digita Compass/Thermometer Mode and take a digita compass reading. COMP wi appear on the dispay to indicate that a digita compass operation is in progress. Ange vaue (in degrees) See Digita Compass Readings on page E-35 for information about what appears on the W If a vaue appears to the right of the direction indicator, it means that the bearing memory (page E-45) screen is dispayed. If this happens, press A to exit the bearing memory screen. E-34 WSW SW SSW W S WW SSE W ESE E E EE 4. After you are finished using the digita compass, press D to return to the mode you entered the Digita Compass/Thermometer Mode from. Digita Compass Readings When you press C to start digita compass measurement, COMP wi appear on the dispay initiay to indicate that a digita compass operation is in progress. About two seconds after you start a digita compass measurement operation, etters on the dispay wi indicate the direction that the 12 o cock position of the watch is pointing. Four pointers that indicate magnetic north, south, east, and west aso wi appear. After the first reading is obtained, the watch wi continue to take digita compass readings automaticay each second for up to 20 seconds. After that, measurement wi stop automaticay. The direction indicator and ange vaue wi show to indicate that digita compass readings are compete. The auto ight switch is disabed during the 20 seconds that digita compass readings are being taken. E-35 The foowing tabe shows the meanings of each of the direction abbreviations that appear on the Direction Meaning Direction Meaning Direction Meaning Direction Meaning orth E E East ESE S South SSW W West WW E ortheast EE SE Southeast SSE SW Southwest WSW W orthwest W orthnortheast Eastnortheast Eastsoutheast Southsoutheast Southsouthwest Westsouthwest Westnorthwest orthnorthwest The margin of error for the ange vaue and the direction indicator is ±11 degrees whie the watch is horizonta (in reation to the horizon). If the indicated direction is northwest (W) and 315 degrees, for exampe, the actua direction can be anywhere from 304 to 326 degrees. that taking a measurement whie the watch is not horizonta (in reation to the horizon) can resut in arge measurement error. You can caibrate the bearing sensor if you suspect the direction reading is incorrect. Any ongoing direction measurement operation is paused temporariy whie the watch is performing an aert operation (daiy aarm, Houry Time Signa, countdown timer aarm) or whie iumination is turned on (by pressing B). The measurement operation resumes for its remaining duration after the operation that caused it to pause is finished. See Digita Compass Precautions (page E-54) for important information about taking direction readings. Caibrating the Bearing Sensor You shoud caibrate the bearing sensor whenever you fee that the direction readings being produced by the watch are off. There are three different caibration methods avaiabe: magnetic decination correction, bidirectiona caibration, and northery caibration. E-36 E-37 Magnetic Decination Correction With magnetic decination correction, you input a magnetic decination ange (difference between magnetic north and true north), which aows the watch to indicate true north. You can perform this procedure when the magnetic decination ange is indicated on the map you are using. that you can input the decination ange in whoe degree units ony, so you may need to round off the vaue specified on the map. If your map indicates the decination ange as 7.4, you shoud input 7. In the case of 7.6 input 8, for 7.5 you can input 7 or 8. Bidirectiona Caibration and orthery Caibration Bidirectiona caibration and northery caibration caibrate the accuracy of the bearing sensor in reation to magnetic north. Use bidirectiona caibration when you want to take readings within an area exposed to magnetic force. This type of caibration shoud be used if the watch becomes magnetized for any reason. With northery caibration, you teach the watch which way is north (which you have to determine with another compass or some other means). The more correcty you perform bidirectiona caibration, the better the accuracy of the bearing sensor readouts. You shoud perform bidirectiona caibration whenever you change environments where you use the bearing sensor, and whenever you fee that the bearing sensor is producing incorrect readings. E-38 E-39

5 To perform magnetic decination correction 1. In the Digita Compass/Thermometer Mode, hod down Magnetic decination ange direction vaue A unti the current magnetic decination settings start (E, W, or OFF) to fash on the This is the setting screen. 2. Use E (East) and B (West) to change the settings. The foowing expains magnetic decination ange direction settings. OFF: o magnetic decination correction performed. The magnetic decination ange with this setting is 0. E: When magnetic north is to the east (east Magnetic decination decination) ange vaue W: When magnetic north is to the west (west decination) You can seect a vaue within the range of W 90 to E 90 with these settings. You can turn off (OFF) magnetic decination correction by pressing E and B at the same time. E-40 The iustration, for exampe, shows the vaue you shoud input and the direction setting you shoud seect when the map shows a magnetic decination of 1 West. 3. When the setting is the way you want, press A to exit the setting screen and take direction and temperature readings. Precautions about bidirectiona caibration You can use any two opposing directions for bidirectiona caibration. You must, however, make sure that they are 180 degrees opposite each other. Remember that if you perform the procedure incorrecty, you wi get wrong bearing sensor readings. Do not move the watch whie caibration of either direction is in progress. You shoud perform bidirectiona caibration in an environment that is the same as that where you pan to be taking direction readings. If you pan to take direction readings in an open fied, for exampe, caibrate in an open fied. E-41 To perform bidirectiona caibration 1. In the Digita Compass/Thermometer Mode, hod down A unti the current magnetic decination settings start to fash on the This is the setting screen. 2. Press D to dispay the bidirectiona caibration screen. At this time, the north pointer fashes at the 12 o cock position and the dispay wi show -1- to indicate that the watch is ready to caibrate the first direction. 3. Pace the watch on a eve surface facing any direction you want, and press C to caibrate the first direction is shown on the dispay whie caibration is being performed. When caibration is successfu, the dispay wi show OK and -2-, and the north pointer fashing at the 6 o cock position. This means that the watch is ready for caibration of the second direction. 4. Rotate the watch 180 degrees. E Press C again to caibrate the second direction is shown on the dispay whie caibration is being performed. When caibration is successfu, the dispay wi show OK and then take direction and temperature readings. To perform northery caibration If you want to perform both northery and bidirectiona caibration, perform bidirectiona caibration first, and then perform northery caibration. This is necessary because bidirectiona caibration cances any existing northery caibration setting. 1. In the Digita Compass/Thermometer Mode, hod down A unti the current magnetic decination settings start to fash on the This is the setting screen. 2. Press D twice to dispay the northery caibration screen. At this time, -- (north) appears on the E Pace the watch on a eve surface, and position it so that its 12 o cock position points north (as measured with another compass). 4. Press C to start the caibration operation is shown on the dispay whie caibration is being performed. When caibration is successfu, the dispay wi show OK and then take direction and temperature readings. E-44 Bearing Memory 12 o cock position orth pointer Bearing memory pointer Direction ange of current reading Bearing Memory Screen Bearing Memory ets you store a direction reading and dispay that reading as you take subsequent digita compass measurements. The Bearing Memory screen dispays the direction ange for the stored direction, aong with an indicator on the dispay that aso indicates the stored direction. When you take digita compass measurements whie the Bearing Memory screen is on the dispay, the direction ange of the current digita compass measurement (as read from the 12 o cock position of the watch) and the currenty stored Bearing Memory direction information wi both be dispayed. E-45 To store a direction ange reading in Bearing Memory 1. Press C to start a digita compass measurement operation (page E-34). If a bearing memory direction ange vaue is aready dispayed, it means that the bearing memory screen is dispayed. If this happens, press A to cear the vaue currenty in Bearing Memory and exit the bearing memory screen. 2. During the 20 seconds that digita compass measurement is in progress, press A to store the current direction ange reading in Bearing Memory. The Bearing Memory direction ange fashes for about one second as it is stored in Bearing Memory. After that, the Bearing Memory screen (which shows the bearing memory direction ange) wi appear, and a 20-second direction reading operation wi start. Whie the Bearing Memory screen is dispayed, you can press C to start a new 20-second direction reading operation, which dispays the direction ange for the direction that the 12 o cock position of the watch is pointed. The direction ange of the current readings wi disappear from the dispay after the direction reading operation is compete. E-46 During the first 20 seconds after you dispay the Bearing Memory screen or during the 20-second direction reading operation whie the Bearing Memory screen is on the dispay, the direction stored in memory is indicated by a Bearing Memory pointer. Pressing A whie the Bearing Memory screen is dispayed wi cear the direction ange currenty in Bearing Memory and start a 20-second direction reading operation. Using the Digita Compass Whie Mountain Cimbing or Hiking This section provides three practica appications for using the watch s buit-in digita compass. Setting a map and finding your current ocation Having an idea of your current ocation is important when mountain cimbing or hiking. To do this, you need to set the map, which means to aign the map so the directions indicated on it are aigned with the actua directions of your ocation. Basicay what you are doing is aigning north on the map with north as indicated by the watch. Finding the bearing to an objective E-47 Determining the direction ange to an objective on a map and heading in that direction To set a map and find your current ocation 1. With the watch on your wrist, position it so the face is horizonta. 2. Press C to take a compass reading. The reading wi appear on the dispay after about two seconds. orth indicated on the map Current ocation 3. Rotate the map without moving the watch so the northery direction indicated on the map matches north as indicated by the watch. If the watch is configured to indicate magnetic north, aign the map s magnetic north with the watch indication. If the watch has been configured with a decination to correct to true north, aign the map s true north with the watch indication. For detais, see Caibrating the Bearing Sensor (page E-37). This wi position the map in accordance with your current ocation. 4. Determine your ocation as you check the geographic contours around you. orth indicated by north pointer E-48 E-49

6 To find the bearing to an objective 1. Set the map so its northery indication is aigned with north as indicated by the watch, and determine your current ocation. See To set a map and find your current ocation on page E-48 for information about how to perform the Objective above step. 2. Set the map so the direction you want to trave on the Current ocation map is pointed straight in front of you. 3. With the watch on your wrist, position it so the face is 12 o cock horizonta. position 4. Press C to take a compass reading. The reading wi appear on the dispay after about two seconds. 5. Sti hoding the map in front of you, turn your body unti north as indicated by the watch and the northery direction on the map are aigned. This wi position the map in accordance with your current ocation, so the bearing to your objective is straight ahead of you. E-50 E-51 To determine the direction ange to an objective on a map and head in that direction 1. Set the map so its northery indication is aigned with north as indicated by the watch, and determine your current ocation. See To set a map and find your current ocation on page E-48 for information about how to perform the above step. Objective 2. As shown in the iustration to the eft, change your Current position so you (and the 12 o cock position of the ocation watch) are pointed in the direction of objective, whie 12 o cock keeping the northery direction indicated on the map position aigned with north as indicated by the watch. If you find it difficut to perform the above step whie keeping everything aigned, first move into the correct position (12 o cock position of the watch pointed at the objective) without worrying about the orientation of the map. ext, perform step 1 again to set the map. E o cock position orth pointer Bearing memory pointer Bearing memory direction ange vaue 3. Press C to take a compass reading. 4. Whie direction ange readings are in progress, press A to record the currenty dispayed direction in Bearing Memory. The direction ange vaue and pointer stored in Bearing Memory wi remain on the dispay for about 20 seconds. See Bearing Memory (page E-45) for more information. 5. ow you can advance whie monitoring the Bearing Memory pointer to ensure that it remains in the 12 o cock position. To re-dispay the Bearing Memory direction ange vaue and Bearing Memory pointer, press C. E-53 Pressing A whie the Bearing Memory direction ange vaue and Bearing Memory pointer are on the dispay wi cear the Bearing Memory data you saved in step 3 and save the current direction reading in Bearing Memory. When mountain cimbing or hiking, conditions or geographic contours may make it impossibe for you to advance in a straight ine. If this happens, return to step 1 and save a new direction to the objective. Digita Compass Precautions This watch features a buit-in magnetic bearing sensor that detects terrestria magnetism. This means that north indicated by this watch is magnetic north, which is somewhat different from true poar north. The magnetic north poe is ocated in northern Canada, whie the magnetic south poe is in southern Austraia. that the difference between magnetic north and true north as measured with a magnetic compasses tends to be greater as one gets coser to either of the magnetic poes. You shoud aso remember that some maps indicate true north (instead of magnetic north), and so you shoud make aowances when using such maps with this watch. E-54 Location Taking a direction reading when you are near a source of strong magnetism can cause arge errors in readings. Because of this, you shoud avoid taking direction readings whie in the vicinity of the foowing types of objects: permanent magnets (magnetic neckaces, etc.), concentrations of meta (meta doors, ockers, etc.), high tension wires, aeria wires, househod appiances (TVs, persona computers, washing machines, freezers, etc.). Accurate direction readings are impossibe whie in a train, boat, air pane, etc. Accurate readings are aso impossibe indoors, especiay inside ferroconcrete structures. This is because the meta framework of such structures picks up magnetism from appiances, etc. Storage The precision of the bearing sensor may deteriorate if the watch becomes magnetized. Because of this, you shoud store the watch away from magnets or any other sources of strong magnetism, incuding: permanent magnets (magnetic neckaces, etc.) and househod appiances (TVs, persona computers, washing machines, freezers, etc.). E-55 Whenever you suspect that the watch may have become magnetized, perform the procedure under To perform bidirectiona caibration (page E-42). E-56 Thermometer This watch uses a temperature sensor to take temperature readings. The watch aso takes direction readings in the Digita Compass/Thermometer Mode. For more information, see Digita Compass (page E-33). To enter and exit the Digita Compass/Thermometer Direction indicator Mode 1. Press C to enter the Digita Compass/Thermometer Mode. Press C to take another reading. 2. Press D to return to the mode you entered the Digita Compass/Thermometer Mode from. The watch wi automaticay return to the mode you entered the Digita Compass/Thermometer Mode Temperature from if you do not perform any operation for about one or two minutes. Ange vaue (in degrees) E-57 Temperature Temperature is dispayed in units of 0.1 C (or 0.2 F). The dispayed temperature vaue changes to C (or F) if a measured temperature fas outside the range of 10.0 C to 60.0 C (14.0 F to F). The temperature vaue wi reappear as soon as the measured temperature is within the aowabe range. Dispay Units You can seect either Cesius ( C) or Fahrenheit ( F) for the dispayed temperature vaue. See To specify temperature unit (page E-61) for more information. Temperature Sensor Caibration The watch s temperature sensor is caibrated at the factory and normay requires no further adjustment. If you notice serious errors in the temperature readings produced by the watch, you can caibrate the sensor to correct the errors. E-58 Incorrecty caibrating the temperature sensor can resut in incorrect readings. Carefuy read the foowing before doing anything. Compare the readings produced by the watch with those of another reiabe and accurate thermometer. If adjustment is required, remove the watch from your wrist and wait for 20 or 30 minutes to give the temperature of the watch time to stabiize. To caibrate the temperature sensor 1. Press C to enter the Digita Compass/Thermometer Mode. 2. Hod down A unti the current magnetic decination correct vaues (page E-40) starts to fash on the This is the setting screen. 3. Press D three times. TEMP wi appear on the dispay aong with the current temperature caibration vaue. E-59

7 4. Use E (+) and B ( ) to change the dispayed caibration by 0.1 C (0.2 F) steps. To return the currenty fashing vaue to its initia factory defaut setting, press E and B at the same time. OFF wi appear in pace of the fashing temperature vaue for about one second, foowed by the initia defaut vaue. 5. Press A to return to the Digita Compass/Thermometer Mode screen, and then take direction and temperature readings. Thermometer Precautions Temperature measurements are affected by your body temperature (whie you are wearing the watch), direct sunight, and moisture. To achieve a more accurate temperature measurement, remove the watch from your wrist, pace it in a we ventiated ocation out of direct sunight, and wipe a moisture from the case. It takes approximatey 20 to 30 minutes for the case of the watch to reach the actua surrounding temperature. Specifying Temperature Unit Use the procedure beow to specify the temperature unit to be used in the Digita Compass/Thermometer Mode. When TOKYO is seected as the Home, the temperature unit is set automaticay to Cesius ( C). These settings cannot be changed. To specify temperature unit 1. In the Timekeeping Mode, hod down A unti SET starts to fash and the city name starts to scro on the E-60 E Press D as many times as necessary unti TEMP is dispayed. See step 3 under To change the current time and date settings (page E-29) for information about how to scro through setting screens. 3. Press D to togge the temperature unit between C (Cesius) and F (Fahrenheit). 4. After the setting is the way you want, press A to exit the setting screen. Temperature Reading Precautions When taking temperature readings, it is best to remove the watch from your wrist in order to eiminate the effects of body heat. Remove the watch from your wrist and aow it to hang freey from your bag or in another ocation where it is not exposed to direct sunight. E-62 E-63 Using the Moon Data In the Moon Data Mode, you can see the current date s Moon phase for your Home. You can specify a date and view Moon data for that date. To enter the Moon Data Mode Use D to seect the Moon Data as shown on page E-22. Moon phase About one second after MOO appears on the dispay, the dispay wi change to show the moon age. Moon age is cacuated to an accuracy of ±1 day. Moon age Month Day Moon Data The Moon phase and Moon age information that appears first when you enter the Moon Data Mode shows the data at noon for your currenty seected Home on the current date, according to the Timekeeping Mode. After that you can specify another date to view data. If the Moon data is not correct, check your Timekeeping Mode settings and correct them if necessary. The Moon phase is dispayed in the Timekeeping Mode, and the Moon Data Mode. If the Moon phase indicator shows a phase that is a mirror image of the actua moon phase in your area, you can use the procedure under Reversing the Dispayed Moon Phase (page E-66) to change it. Use the Moon Data Screen to specify the Moon Data date. You can use E (+) to change the dispayed date in one-day increments. Pressing E wi dispay the year of the dispayed date. E-64 E-65 Reversing the Dispayed Moon Phase The eft-right (east-west) appearance of the Moon depends on whether the Moon is north of you (northery view) or south of you (southery view) as you view it. You can use the procedure beow to reverse the dispayed Moon phase so it matches the actua appearance of the Moon where you are ocated. To determine the viewing direction of the Moon, use a compass to take a direction reading of the Moon at its meridian passage. For information about the Moon phase indicator, see Moon Phase Indicator (page E-68). To reverse the dispayed Moon phase 1. In the Moon Data Mode, hod down A unti the Moon phase indicator starts to fash. This is the indicator switching screen. 2. Press E to togge the Moon phase indicator between the southery view (indicated by ) and northery view (indicated by ). orthery view: Moon is north of you. Southery view: Moon is south of you. 3. When the Moon phase indicator setting is the way you want, press E to exit the switching screen and return to the Moon Data Mode screen. E-66 E-67 Moon Phase Indicator Modue 3261 Moon Phase Indicator Modue 3281 The Moon phase indicator of this watch indicates the current phase of the Moon as shown beow. It is based on the view of the eft side of the moon at meridian transit from the northern hemisphere of the Earth. If the appearance of the Moon phase indicator is reversed from the actua Moon as viewed from your ocation, you can use the procedure under To reverse the dispayed Moon phase (page E-67) to change the indicator. Moon Phase Indicator Moon Age Moon Phase Modue 3261 Modue 3281 (part you cannot see) Moon phase (part you can see) ew Moon First Quarter (Waxing) E-68 E-69

8 Moon Phase Indicator Moon Age Moon Phase E-70 Moon phase (part you can see) Modue 3261 Modue Fu Moon (part you cannot see) Last Quarter (Waning) Checking the Current Time in a Different Time Zone You can use the Word Time Mode to view the current time in one of 31 time zones (48 cities) around the gobe. The city that is currenty seected in the Word Time Mode is caed the Word Time. Currenty seected To enter the Word Time Mode Word Time Use D to seect the Word Time Mode (WT) as shown on page E-22. Entering the Word Time Mode wi cause WT to be dispayed for the mode name for about one second, and then the name of the currenty seected city wi scro on the After that, the city code wi be dispayed. If you seect a different city, the city name wi scro first and then Current time in the the city code wi appear. For information about city codes, currenty seected see the Code Tabe at the back of this manua. Word Time To view the name of the currenty seected city, press A in the Word Time Mode. This wi cause the city name to scro on the E-71 To view the time in another time zone In the Word Time Mode, use E (East) to scro through city names. Pressing E and B at the same time wi jump to the UTC time zone. To specify standard time or dayight saving time (DST) for a city 1. In the Word Time Mode, use E (East) to dispay the city name (time zone) whose Standard Time/Dayight Saving Time setting you want to change. 2. Hod down A to togge between Dayight Saving Time (DST indicator dispayed) and Standard Time (DST indicator not dispayed). DST indicator The DST indicator is shown on the Word Time Mode screen whie Dayight Saving Time is turned on. Using the Word Time Mode to change the DST setting of the city name that is seected as your Home aso wi change the Timekeeping Mode time DST setting. E-72 that you cannot switch between standard time/dayight saving time (DST) whie UTC is seected as the Word Time. that the standard time/dayight saving time (DST) setting affects ony the currenty seected time zone. Other time zones are not affected. E-73 Using the Stopwatch The stopwatch measures eapsed time, spit times, and two finishes. Current time Hours To enter the Stopwatch Mode Use D to seect the Stopwatch Mode (STW) as shown on page E-22. About one second after STW appears on the dispay, the dispay wi change to show the stopwatch hours. To perform an eapsed time operation Seconds Minutes 1/100 second E E E E A Start Stop (Restart) (Stop) Reset To pause at a spit time E A A E A Start Spit (SPL dispayed) Spit reease Stop Reset To measure two finishes E A E A A Start Spit First runner finishes. Dispay time of first runner Stop Second runner finishes. Spit reease Dispay time of second runner Reset E-74 E-75 The Stopwatch Mode can indicate eapsed time up to 999 hours, 59 minutes, seconds. Once started, stopwatch timing continues unti you press A to stop it, even if you exit the Stopwatch Mode to another mode and even if timing reaches the stopwatch imit defined above. Exiting the Stopwatch Mode whie a spit time is frozen on the dispay cears the spit time and returns to eapsed time measurement. Using the Countdown Timer The countdown timer can be configured to start at a preset time, and sound an aarm when the end of the countdown is reached. To enter the Countdown Timer Mode Use D to seect the Countdown Timer Mode (TMR) as shown on page E-22. About one second after TMR appears on the dispay, the dispay wi change to show the countdown time hours. Current time Countdown time (Hour, minutes, seconds) E-76 E-77 To specify the countdown start time 1. Enter the Countdown Timer Mode. If a countdown is in progress (indicated by the seconds counting down), press E to stop it and then press A to reset to the current countdown start time. If a countdown is paused, press A to reset to the current countdown start time. 2. Hod down A unti the hour setting of the current countdown start time starts to fash. This is the setting screen. 3. Press D to move the fashing between the hour and minute settings. 4. Use E (+) and B ( ) to change the fashing item. To set the starting vaue of the countdown time to 24 hours, set 0H Press A to exit the setting screen. To perform a countdown timer operation E E E E A Start Stop (Restart) (Stop) Reset Before starting a countdown timer operation, check to make sure that a countdown operation is not in progress (indicated by the seconds counting down). If it is, press E to stop it and then A to reset to the countdown start time. An aarm sounds for ten seconds when the end of the countdown is reached. This aarm wi sound in a modes. The countdown time is reset to its starting vaue automaticay when the aarm sounds. To stop the aarm Press any button. E-78 E-79

9 Using the Aarm Current time Aarm time (Hour : Minutes) E-80 You can set four one-time aarms and one snooze aarm. When an aarm is turned on, the watch wi beep for about 10 seconds each day when the time in the Timekeeping Mode reaches the preset aarm time. This is true even if the watch is not in the Timekeeping Mode. You can aso turn on an Houry Time Signa, which wi cause the watch to beep twice every hour on the hour. To enter the Aarm Mode Use D to seect the Aarm Mode (ALM) as shown on page E-22. About one second after ALM appears on the dispay, the dispay wi change to show one of the foowing aarm screens: AL1 (Aarm 1) through AL4 (Aarm 4), SZ (snooze aarm), or SIG (Houry Time Signa). When you enter the Aarm Mode, the screen you were viewing when you ast exited the mode appears first. To set an aarm time 1. In the Aarm Mode, use E to scro through the aarm screens unti the one whose time you want to set is dispayed. Aarm O/OFF indicator AL1 AL2 AL3 SIG SZ AL4 2. Hod down A unti the aarm time starts to fash. This is the setting screen. 3. Press D to move the fashing between the hour and minute settings. E Whie a setting is fashing, use E (+) and B ( ) to change it. When setting the aarm time using the 12-hour format, take care to set the time correcty as a.m. (no indicator) or p.m. (P indicator). 5. Press A to exit the setting screen. To test the aarm In the Aarm Mode, hod down E to sound the aarm. To turn an aarm and the Houry Time Signa on and off 1. In the Aarm Mode, use E to seect an aarm or the Houry Time Signa. E When the aarm or the Houry Time Signa you want is seected, press A to turn it on and off. The aarm on indicator and houry time signa on indicator are dispayed when the aarm and/or signa is turned on. The aarm on indicator and the Houry Time Signa on indicator are shown on the dispay in a modes whie these functions are turned on. If any aarm is on, the aarm on indicator is shown Aarm on indicator Houry time signa on indicator on the dispay in a modes. The aarm on indicator fashes whie the aarm is sounding. The snooze aarm indicator (SZ) fashes whie the snooze aarm is sounding and during the 5-minute intervas between aarms. To stop the aarm Press any button. E-83 Iumination The dispay of the watch is iuminated for easy reading in the dark. The watch s auto ight switch turns on iumination automaticay when you ange the watch towards your face. The auto ight switch must be turned on (page E-86) for it to operate. To turn on iumination manuay Press B in any mode to iuminate the You can use the procedure beow to seect either 1.5 seconds or 3 seconds as the iumination duration. When you press B, the dispay wi remain iuminated for about 1.5 seconds or 3 seconds, depending on the current iumination duration setting. The above operation turns on iumination regardess of the current auto ight switch setting. Iumination is disabed whie configuring sensor measurement mode settings, and during bearing sensor caibration. To change the iumination duration 1. In the Timekeeping Mode, hod down A unti SET starts to fash and the city name starts to scro on the 2. Keep pressing D unti LT1 or LT3 is dispayed. See step 3 under To change the current time and date settings (page E-29) for information about how to scro through setting screens. 3. Press E to togge the iumination duration between three seconds (LT3 dispayed) and 1.5 seconds (LT1 dispayed). 4. After the settings are the way you want, press A to exit the setting screen. E-84 E-85 About the Auto Light Switch Turning on the auto ight switch causes iumination to turn on, whenever you position your More than wrist as described beow in any mode. 40 Moving the watch to a position that is parae to the ground and then titing it towards you more than 40 degrees causes iumination to Wear the watch on the turn on. outside of your wrist Warning! Aways make sure you are in a safe pace whenever you are reading the dispay of the watch using the auto ight switch. Be especiay carefu when running or engaged in any other activity that can resut in accident or injury. Aso take care that sudden iumination by the auto ight switch does not starte or distract others around you. When you are wearing the watch, make sure that its auto ight switch is turned off before riding on a bicyce or operating a motorcyce or any other motor vehice. Sudden and unintended operation of the auto ight switch can create a distraction, which can resut in a traffic accident and serious persona injury. The auto ight switch is aways disabed, regardess of its on/off setting, when any one of the foowing conditions exists. Whie an aarm is sounding During sensor measurement Whie a bearing sensor caibration operation is being performed in the Digita Compass/Thermometer Mode E-86 E-87 To turn the auto ight switch on and off In the Timekeeping Mode, hod down B for about three Auto ight switch on indicator seconds to togge the auto ight switch on (LT dispayed) and off (LT not dispayed). The auto ight switch on indicator (LT) is on the dispay in a modes whie the auto ight switch is turned on. The auto ight switch turns off automaticay whenever battery power drops to Leve 4 (page E-14). Iumination Precautions Frequent dispay iumination can run down the battery quicky and require charging. The foowing guideines give an idea of the charging time required to recover from a singe iumination operation. Approximatey five minutes exposure to bright sunight coming in through a window Approximatey 50 minutes exposure to indoor fuorescent ighting E-88 The eectro-uminescent pane that provides iumination oses power after very ong use. Iumination may be hard to see when viewed under direct sunight. Iumination turns off automaticay whenever an aarm sounds. Frequent use of iumination runs down the battery. Auto ight switch precautions Wearing the watch on the inside of your wrist, movement of your arm, or vibration of your arm can cause frequent activation of the auto ight switch and iumination of the To avoid running down the battery, turn off the auto ight switch whenever engaging in activities that might cause frequent iumination of the that wearing the watch under your seeve whie the auto ight switch is turned on can cause frequent iumination of the dispay and can run down the battery. E-89