DIGITAL CINEMA PROJECTOR SRX-R320. INSTALLATION MANUAL 1st Edition

Transcription

1 DIGITAL CINEMA PROJECTOR INSTALLATION MANUAL 1st Editio

2 !! WARNING This maual is iteded for qualifi ed service persoel oly. To reduce the risk of electric shock, fi re or ijury, do ot perform ay servicig other tha that cotaied i the operatig istructios uless you are qualifi ed to do so. Refer all servicig to qualifi ed service persoel.! WARNUNG Die Aleitug ist ur für qualifi ziertes Fachpersoal bestimmt. Alle Wartugsarbeite dürfe ur vo qualifi ziertem Fachpersoal ausgeführt werde. Um die Gefahr eies elektrische Schlages, Feuergefahr ud Verletzuge zu vermeide, sid bei Wartugsarbeite strikt die Agabe i der Aleitug zu befolge. Adere als die agegebe Wartugsarbeite dürfe ur vo Persoe ausgeführt werde, die eie spezielle Befähigug dazu besitze.! AVERTISSEMENT Ce maual est destié uiquemet aux persoes compétetes e charge de l etretie. Afi de réduire les risques de décharge électrique, d icedie ou de blessure effectuer que les réparatios idiquées das le mode d emploi à mois d être qualifi é pour e effectuer d autres. Pour toute réparatio faire appel à ue persoe compétete uiquemet. : NETWORK For kudee i Norge Dette utstyret ka kobles til et IT-strømfordeligssystem. For safety, do ot coect the coector for peripheral device wirig that might have excessive voltage to the followig port. : NETWORK coector Follow the istructios for the above port.

3 Table of Cotets Maual Structure 2. Adjustmet Purpose of this maual... 3 Related mauals... 3 Trademarks Istallatio Outlie Removig/Istallig the Cabiet Pael Name of Cabiet Pael Pael (U7) Block Assembly Pael (U2) Block Assembly Pael (U3) Pael (U6) Pael (U5) Pael (U1B) Pael (U1) Pael (U4) Block Assembly Pael (U4B) Pael (U8) Tilt Agle Adjustmet Istallig the Duct Istallig the Projectio Les Istallig the Les Cover Istallig the Status Light Assembly Istallig the Touch Pael Adapter Istallig the Lamp Bulb Istallig LMT-300 ad Coectig with the Uit Istallig the Optioal Board to INPUT A ad INPUT B Iterlock Termial Coectig ad Wirig of Exteral Device Coectig the Power Cord Dimesios Istallatio of SRX Cotroller Istallatio Coectio Startup ad Iitializatio of SRX Cotroller Startup of This Uit Optical Axis Adjustmet of Lamp Les Adjustmet (H Shift, V Shift, Zoom, ad Focus Adjustmets) Illumiatio Area Adjustmet ad Registratio Adjustmet Illumiatio Area Adjustmet Registratio Adjustmet Scree Illumiace Settig ad Color Space Coversio (CSC Adjustmet) Field Agle Adjustmet Side Maskig Height Maskig Settig of Fuctio Memory Settig of New Fuctio Memory Chage i Settig of Registered Fuctio Memory Copyig of Registered Fuctio Memory to Create New Fuctio Memory Switchig of Registered Fuctio Memory How to Use the SRX Cotroller Cofiguratio Fuctio Memory Fuctios of Each Widow Error Message 1

4

5 Maual Structure Purpose of this maual This maual is the istallatio maual of Digital Ciema Projector. This maual is iteded for use by traied system ad service egieers, ad describes the iformatio for istallatio of the uit. The DIF-188 board mouted o this uit as stadard equipmet is equivalet of LKRI-005. For the service iformatio o the DIF-188 board, refer to the LKRI-005 service maual. Related mauals The followig mauals are prepared for this uit.. Operatig Istructios (supplied with this uit) This maual describes the iformatio required for the actual maagemet ad operatio of this uit.. Service Maual (available o request) This maual describes the iformatio for periodic maiteace ad detailed service. Trademarks Trademarks ad registered trademarks used i this maual are follows.. Widows ad Widows XP are registered trademarks of Microsoft Corporatio i the Uited States ad other coutries.. Itel ad Petium are registered trademarks of Itel Corporatio or its subsidiaries i the Uited States ad other coutries.. Etheret is a registered trademark of Xerox Corporatio. Other system ames, product ames, ad compay ames appearig i this maual are trademarks or registered trademarks of their respective holders. 3

6

7 Sectio 1 Istallatio Outlie The light source lamp bulb ad projectio les are optioally available. You ca icorporate them i the system as required. For selectig the light source lamp ad projectio les, please cotact your local Soy Sales Office/Service Ceter. Before turig o the power of the mai uit, perform the followig procedure as required. (For details, refer to the descriptio of each sectio.) For the removal of the cabiet pael required for each procedure, refer to Sectio 1-1. m. It is ot required to perform steps 1 to 11 sequetially. However, do ot perform the coectio of power cord i step 12 before completig steps 1 to 11.. Be sure to remove the lamp bulb whe movig this uit. 1. Adjust the tilt agle. (Refer to Sectio 1-2.) 2. Istall the duct. (Refer to Sectio 1-3.) 3. Istall the projectio les. (Refer to Sectio 1-4.) 4. Istall the les cover. (Refer to Sectio 1-5.) 5. Istall the status light assembly. (Refer to Sectio 1-6.) 6. Istall the touch pael adapter. (Refer to Sectio 1-7.) 7. Istall the lamp bulb. (Refer to Sectio 1-8.) 8. Istall LMT-300 ad coect with this uit. (Refer to Sectio 1-9.) 9. Istall the optioal board to INPUT A ad INPUT B slot. (Refer to Sectio 1-10.) 10. Coect the iterlock coector. (Refer to Sectio 1-11.) 11. Coect ad wire the exteral device. (Refer to Sectio 1-12.) 12. Coect the power cord. (Refer to Sectio 1-13.) 1-1. Removig/Istallig the Cabiet Pael The four (each two) keys of the pael (U7) block assembly ad two pael (U4) block assembly described i this sectio are supplied with this uit Name of Cabiet Pael Pael (U7) block assembly Pael (U8) Pael (U4) block assembly Pael (U1) Pael (U3) Pael (U6) Pael (U1B) Frot side Pael (U2) block assembly Pael (U4B) Rear side Pael (U5) Fig

8 Pael (U7) Block Assembly 1. Release the lock o the pael (U7) block assembly. 2. Remove the pael (U7) block assembly i the directio of the arrow with attetio to the three hooks. 3. To istall, reverse the removal procedure. Pael (U7) block assembly Lock Hooks Fig Pael (U2) Block Assembly 1. Remove the pael (U7) block assembly. (Refer to Sectio ) 2. Loose the two screws (with drop-safe), the remove the two grilles. 3. Remove the five screws, the raise the pael (U2) block assembly i the directio of arrow with attetio to the twelve hooks. 4. Remove the pael (U2) block assembly i the directio of arrow. Hooks Screws Hooks Screws (with drop-safe) 5. To istall, reverse the removal procedure. Hooks Hooks Hooks Pael (U2) block assembly Grilles Fig

9 Pael (U3) 1. Remove the pael (U7) block assembly. (Refer to Sectio ) 2. Remove the pael (U2) block assembly. (Refer to Sectio ) 3. Remove the three screws, the remove the pael (U3) i the directio of the arrow. 4. To istall, reverse the removal procedure. Pael (U3) Screws Fig Pael (U6) 1. Remove the pael (U7) block assembly. (Refer to Sectio ) 2. Remove the five screws, the raise the pael (U6) i the directio of arrow with attetio to the eleve hooks. 3. Remove the pael (U6) i the directio of arrow. Screws Hooks 4. To istall, reverse the removal procedure. Hooks Pael (U6) Hooks Hooks Hooks Fig

10 Pael (U5) 1. Remove the pael (U7) block assembly. (Refer to Sectio ) 2. Remove the pael (U6). (Refer to Sectio ) 3. Remove the three screws, the remove the pael (U5) i the directio of arrow. 4. To istall, reverse the removal procedure. Pael (U5) Screws Fig Pael (U1B) 1. Remove the pael (U7) block assembly. (Refer to Sectio ) 2. Remove the pael (U2) block assembly. (Refer to Sectio ) 3. Remove the pael (U6). (Refer to Sectio ) 4. Remove the six screws, the lower the pael (U1B) i the directio of arrow. 5. Remove the pael (U1B) i the directio of arrow. 6. To istall, reverse the removal procedure. Screws Pael (U1B) Screws Fig

11 Pael (U1) 1. Remove the pael (U7) block assembly. (Refer to Sectio ) 2. Remove the pael (U2) block assembly. (Refer to Sectio ) 3. Remove the pael (U6). (Refer to Sectio ) 4. Remove the pael (U1B). (Refer to Sectio ) 5. Remove the eight screws, the remove the pael (U1) i the directio of arrow. 6. To istall, reverse the removal procedure. Screws Screws Pael (U1) Screws Screws Fig

12 Pael (U4) Block Assembly 1. Release the lock o the pael (U4) block assembly. 2. Ope the pael (U4) block assembly at a agle of about eighty degrees. 3. Raise to remove the pael (U4) block assembly from the two hige portios. 4. To istall, reverse the removal procedure. About 80 degrees Pael (U4) block assembly Hige portios Pael (U4) block assembly Lock Fig

13 Pael (U4B) 1. Remove the pael (U7) block assembly. (Refer to Sectio ) 2. Remove the pael (U2) block assembly. (Refer to Sectio ) 3. Remove the pael (U3). (Refer to Sectio ) 4. Remove the pael (U6). (Refer to Sectio ) 5. Remove the pael (U5). (Refer to Sectio ) 6. Ope the pael (U4) block assembly. (Refer to steps 1 ad 2 i Sectio ) 7. Remove the four screws, the remove the pael (U4B) i the directio of arrow with attetio to the two hooks. 8. To istall, reverse the removal procedure. Screws Screws Pael (U4B) Hooks Fig

14 Pael (U8) 1. Remove the pael (U7) block assembly. (Refer to Sectio ) 2. Remove the pael (U2) block assembly. (Refer to Sectio ) 3. Remove the pael (U3). (Refer to Sectio ) 4. Remove the pael (U6). (Refer to Sectio ) 5. Remove the pael (U5). (Refer to Sectio ) 6. Remove the two screws, the remove the STL cover. 7. Remove the eight screws, the remove the pael (U8). Screws 8. To istall, reverse the removal procedure. STL cover Screws Pael (U8) Screws Fig

15 1-2. Tilt Agle Adjustmet For further adjustmet, 2-6. Field Agle Adjustmet is required. I the case of tilt agle uder 5 degrees: Adjust the tilt agle usig the adjuster i the lower portio of this uit. 1. Loose the ut. 2. Adjust the tilt agle by rotatig the adjuster i the lower portio of this uit. 3. Secure the adjuster by tighteig the ut to the adjuster pipe side. Adjuster pipe Nut Adjuster Fig. 1-2a 1-9

16 I the case of tilt agle from 5 to 10 degrees: 1. Remove the pael (U7) block assembly. (Refer to Sectio ) 2. Remove the pael (U2) block assembly. (Refer to Sectio ) 3. Remove the pael (U3). (Refer to Sectio ) 4. Remove the pael (U6). (Refer to Sectio ) 5. Remove the pael (U5). (Refer to Sectio ) 6. Set the tools such as jack at both sides of frame, the raise the rear portio of the mai uit. 7. Remove the four M8 bolts. 8. Move the adjuster pipe assembly dowward ad isert the four M8 bolts ito the four holes to secure it. 9. Lower the jack ad attach the pael (U5), pael (U6), pael (U3), pael (U2) block assembly ad pael (U7) block assembly. Whe settig the jack, pay attetio to the holes o the bottom of flame. Frame Jack Jack M8 bolts Jack Holes M8 bolts Adjuster pipe assembly Adjuster pipe assembly Fig. 1-2b 1-10

17 I the case of fixig this uit: This uit ca be fixed to the floor usig the achor BKT. Whe fixig this uit, attach the achor BKT to the adjuster as show i the illustratio. Part ame Achor BKT (optioally available): Adjuster Achor BKT Fig. 1-2c 1-3. Istallig the Duct Attach the commercially available 8-ich duct to the duct coectio of the pael (U8) of this uit. Whe attachig the duct, be careful ot to bed it so that the exhaust air flows smoothly. Exteral fa (exhaust air) air volume specificatio The followig exhaust air volume is required for the 8-ich duct. Exhaust air volume: 450 to 550 ft 3 /mi (12.7 to 15.6 m 3 /mi) 8-ich duct Duct coectio Fig

18 1-4. Istallig the Projectio Les 1. Attach the projectio les. 2. Alig the otch of les bracket with the lie of projectio les ad tighte the supplied four bolts i the order from to. 3. Coect the three cables (focus, zoom ad POTEN- TIO). Tighte the bolts i the order from to. Notch Lie Do ot attach the les cover before completig the les adjustmet. (Refer to Sectio 2-3.) Les bracket Projectio les Pis Projectio les Bolts Zoom cable Focus cable POTENTIO cable Fig

19 1-5. Istallig the Les Cover 1. Attach the les cover i the directio of arrow with attetio to the three hooks. The les covers are same parts, so they ca be attached both upper ad lower. Hook Hook Hook Les cover Fig. 1-5a 2. Attach the les cover i the directio of arrow with attetio to the three hooks. Whe attachig the les cover, alig the four covex portios with the four holes. Hook Les cover Hook Hook Covex portios Les cover Holes Hole Covex portios Hole Les cover Fig. 1-5b 1-13

20 1-6. Istallig the Status Light Assembly 1. Ope the pael (U4) block assembly. (Refer to steps 1 ad 2 i Sectio ) 2. Remove the two screws, the remove the STL cover. Store the removed STL cover. Screws STL cover Fig. 1-6a 3. Attach the oe-touch bush (supplied with the uit) to the hole i the upper area of this uit. 4. Route the haresses through the hole i the upper area of the uit, the coect the two haresses of the status light assembly ad the two haresses of the uit. The tags are attached o the haresses (4-pi). Coect them with the followig combiatio of the idicatio o the tag. Status light side LIGHT (oe) This uit side LIGHT SW Screws Status light assembly Haresses Oe-touch bush 5. Attach the status light assembly with the two screws. 6. Close the pael (U4) block assembly. Haresses Fig. 1-6b 1-14

21 1-7. Istallig the Touch Pael Adapter The recommeded operatig moitor maufactured by ADVANTECH ca be attached to the supplied touch pael adapter. For details, cotact your local Soy Sales Office/Service Ceter. 1. Attach the TPC base to the pael (U4B) with the six M4 screws. Rear side M4 screws TPC base Fig. 1-7a 2. Attach the TPC bracket to the operatig moitor with the six M3 screws. M3 screws TPC bracket M3 screws Operatig moitor Upper side Fig. 1-7b 1-15

22 3. Pull the kob of the TPC base i the directio of the arrow, the fix it by rotatig i the directio of the arrow. 4. Attach the operatig moitor to the TPC base as show i the illustratio. 5. Alig the kob with the agular adjustmet hole, the retur the kob to the origial positio i the reverse order of step 3. Operatig moitor TPC bracket Agular adjustmet hole TPC base TPC base TPC base Kob Kob Fig. 1-7c 1-16

23 1-8. Istallig the Lamp Bulb w. Be sure to tur off the power of this uit before istallig the lump bulb.. Be sure that oly the qualified service persoel ca istall the lamp bulb. For the qualificatio, please cotact your local Soy Sales Office/Service Ceter.. Whe istallig the lamp bulb, be sure to wear the protectio suit kit (J A (M size), J A (L size), or J A (XL size)). Also, wear the shoes that cover the istep of the foot completely.. Be extremely careful whe hadlig the xeo lamp bulb because a high voltage is applied to it.. Do ot touch the lamp bulb with bear hads. Otherwise, it may break the lamp bulb. Wearig of protectio suit kit 1. Wear the jacket ad trousers. 2. Wear the arm cover o both hads so that the wrists are completely covered. 3. Wear the hood ad attach the face shield. 4. Adjust the face shield to the head size usig the adjuster o the back of the face shield. 5. Wear the glove o both hads. Face shield Hood Adjuster Face shield Protectio suit Arm cover Glove Arm cover Glove Fig. 1-8a 1-17

24 Procedure m. Keep the serial code label affixed o the Operatig Istructios of the lamp bulb which is required for istallatio.. Keep the materials such as packagig box, case, protectio sheet because they are used whe disposig of the used lamp bulb.. As for the aode haress itegrated lamp bulb, steps 1 ad 2 are ot required. 1. Loose the screw ad bed portio A of the aode haress. Screw Portio A Aode haress Fig. 1-8b 2. Attach the aode haress to the aode side of the lamp bulb, the tighte the screw. (Tighteig torque: 1.2 N.m) Aode side Lamp bulb Aode haress Screw Fig. 1-8c 1-18

25 3. Ope the pael (U4) block assembly. (Refer to steps 1 ad 2 i Sectio ) 4. Loose the screw (with drop-safe), the rotate the cold mirror assembly i the directio of the arrow. 5. Loose the five screws (with drop-safe), the remove the maiteace cover. Cold mirror assembly Pael (U4) block assembly Screw (with drop-safe) Maiteace cover Screws (with drop-safe) Screw (with drop-safe) Cold mirror assembly Fig. 1-8d 6. Remove the bolt from the aode termial. 7. Loose the hexago socket set screw of the cathode termial. Cathode termial Hexago socket set screw Aode termial Bolt Fig. 1-8e 1-19

26 8. Remove the plastic cover from the lamp bulb. Lamp bulb Plastic cover Fig. 1-8f 9. Remove the protectio sheet from the lamp bulb. Lamp bulb Protectio sheet Fig. 1-8g 1-20

27 10. Loose the kob, the move the aode holder i the directio of the arrow. 11. Isert portio A of the lamp ito the cathode termial. Whe attachig the lamp bulb, be careful ot to damage the reflector portio. Also, be careful ot to damage the glass of lamp bulb. Otherwise, it may break the lamp bulb. 12. Hold the cathode side of the lamp bulb firmly ad raise the aode side. The, retur the aode holder to the origial positio ad tighte the kob. Reflector portio Cathode termial Aode holder Kob Portio A Lamp bulb Fig. 1-8h 1-21

28 13. Place the aode side of the lamp bulb o the aode holder. 14. Attach the aode haress to the aode termial, the tighte the bolt. (Tighteig torque: 1.5 N.m). After istallig the aode haress separated lamp bulb, if there is a clearace i portio A of the aode holder, adjust it by bedig the aode haress so that there is o clearace betwee the aode holder ad the lamp bulb. 15. Tighte the hexago socket set screw of the cathode termial. (Tighteig torque: 1.2 N.m) Be sure that there is o clearace betwee the ed face of the cathode termial ad the surface C of the lamp bulb. I the case of aode haress itegrated lamp bulb Aode holder Aode haress Aode holder Lamp bulb I the case of aode haress separated lamp bulb Lamp bulb No clearace Portio A 16. Attach the pael (U4) block assembly i the reverse order of steps 3 to 5. Aode haress Adjust by bedig this portio. Cathode termial Hexago socket set screw Aode holder Kob Aode haress Bolt Aode termial Ed face Cathode termial Lamp bulb Surface C Fig. 1-8i 1-22

29 1-9. Istallig LMT-300 ad Coectig with the Uit 1. Remove the pael (U7) block assembly. (Refer to Sectio ) 2. Remove the pael (U2) block assembly. (Refer to Sectio ) 3. Remove the pael (U6). (Refer to Sectio ) 4. Remove the pael (U1B). (Refer to Sectio ) 5. Loose the two screws (with drop-safe), the remove the frot pael from the LMT-300. LMT-300 Screw (with drop-safe) Frot pael Screw (with drop-safe) Fig. 1-9a 1-23

30 6. Istall LMT-300 i this uit. 7. Secure LMT-300 with the four istallatio screws (B5 x 12) supplied with LMT Attach the HDD uit supplied with LMT-300. (Refer to LMT-300 Istallatio Maual.) 9. Coect the haress of this uit to the STATUS LIGHT coector i the frot pael. 10. Attach the frot pael. Tighte the screws (with drop-safe). Tighteig torque: 0.8 N.m STATUS LIGHT coector Haress B5 x 12 LMT-300 B5 x 12 Frot pael Screw (with drop-safe) Screw (with drop-safe) Fig. 1-9b 1-24

31 11. Attach the power cord to LMT Attach the LMT duct (A) with the screw. Whe attachig the LMT duct (A), route the power cord through the otch. 13. Attach the LMT duct (B) with the three screws. LMT duct (A) Notch Power cord Screw Screw Screws LMT duct (A) LMT duct (B) Fig. 1-9c 1-25

32 14. Coect INPUT-C A of the uit with PROJECTOR OUTPUT A of LMT-300 ad INPUT-C B with PRO- JECTOR OUTPUT B usig the supplied coectio codes. 15. Coect the etwork coector of this uit with the PRJ CTRL coector of LMT-300 usig the supplied LAN cable. 16. Coect the coector (CN6) o the CN-3225 board of this uit with the CSS coector of LMT-300 usig the supplied CSS cable. INPUT-C B INPUT-C A Shield case assembly (1) CN-3225 board 17. Attach the pael (U1B) i the reverse order of step Attach the pael (U6) i the reverse order of step Attach the pael (U2) block assembly i the reverse order of step Attach the pael (U7) block assembly i the reverse order of step 1. LMT-300 Network coector CSS PRJ CTRL PROJECTOR OUTPUT B PROJECTOR OUTPUT A Fig. 1-9d 1-26

33 1-10. Istallig the Optioal Board to INPUT A ad INPUT B For both INPUT A ad INPUT B slots, the optioal board, LKRI-003 or LKRI-005 ca be istalled. The istallig procedure for each slot is same. For INPUT A slot, LKRI-005 is istalled before shipmet. Replace it as ecessary. Parts iformatio. Fixed Plate (HIF) 320: (For LKRI-003). Fixed Plate (DIF) 320: (For LKRI-005). Hadle: (Usig 2 pcs) Procedure (LKRI-003) 1. Remove the six screws, the remove the pael (HIF-44) ad figer holder (HIF). LKRI-003 B3 x 8 Pael (HIF-44) Figer holder (HIF) Fig. 1-10a 2. Attach the fixed plate (HIF) 320 usig the six screws removed i step Attach the two hadles to the fixed plate (HIF) 320. LKRI-003 Hadle B3 x 8 Hadle Fixed plate (HIF) 320 Fig. 1-10b 1-27

34 4. Remove the two screws, the remove the blak pael. Store the removed blak pael. 5. Remove the te screws, the remove the pael cover (IF). Pael cover (IF) Blak pael PSW4 x 10 PSW4 x 10 Fig. 1-10c 6. Isert the LKRI-003 board ito INPUT B slot, ad coect it securely. 7. Attach the pael cover (IF) usig the twelve screws. INPUT B LKRI-003 Pael cover (IF) PSW4 x 10 Fig. 1-10d 1-28

35 Procedure (LKRI-005) 1. Remove the two screws, the remove the pael (DIF-188) ad figer holder (DIF). LKRI-005 B3 x 8 Pael (DIF-188) Figer holder (DIF) Fig. 1-10e 2. Attach the fixed plate (DIF) 320 usig the two screws removed i step Attach the two hadles to the fixed plate (DIF) 320. LKRI-005 Hadle B3 x 8 Hadle Fixed plate (DIF) 320 Fig. 1-10f 4. Remove the two screws, the remove the blak pael. Store the removed blak pael. 5. Remove the te screws, the remove the pael cover (IF). Pael cover (IF) Blak pael PSW4 x 10 PSW4 x 10 Fig. 1-10g 1-29

36 6. Isert the LKRI-005 board ito INPUT B slot, ad coect it securely. 7. Attach the pael cover (IF) usig the twelve screws. INPUT B LKRI-005 Pael cover (IF) PSW4 x 10 Fig. 1-10h 1-30

37 SRW-5000 HD DIGITAL VIDEO CASSETTE RECORDER Coectio with each equipmet m. Coect each equipmet with the power tured off state.. Use the coectig cables applicable to each termial.. Isert the plug securely. Icomplete coectio may cause a image trouble. Whe discoectig the plug, be sure to hold the plug with your had.. Refer to the Operatig Istructios of the equipmet to be coected. I case of LKRI-003 Iput BNC type (2) HD-SDI: Serial digital (1.485 Gbps) Compliat to SMPTE-292M/ITU-R, BT709/BTA-S004 Dual-lik HD-SDI: Serial digital (1.485 Gbps) Compliat to SMPTE-372M DC-SDI: Serial digital (1.485 Gbps) Compliat to PsF, 24 PsF, 24P LKRI-003 Output BNC type (2) Loop-through output To IN termial Quatizatio characteristics 10 bits/samplig HD-SDI coectig cable (optioally available) To HD-SDI output termial HDCAM recorder/player, etc. Fig. 1-10i 1-31

38 I case of LKRI-005 m. For INPUT A slot, LKRI-005 is istalled by default. However, LKRI-003 ca be istalled.. Whe usig a log cable, the image may ot be displayed properly due to the sigal atteuatio.. Whe the 10 bit sigle mode is selected, the DVI cable applicable to Dual-lik is required. 1. Coect the commercially available DVI cable to the termial accordig to the iput sigal. LKRI-005 Iput sigal Used termial Durig ormal operatio DVI1.0 compliat Sigal level: Full Rage DVI-D termial 10 bit sigal of its ow specifi catio Durig iput (10 bit twi mode) Sigal level: Full Rage DVI-D termial ad AUX termial 10 bit sigal of its ow specifi catio Durig iput (10 bit sigle mode) Sigal level: Full Rage DVI-D termial Used durig sigal iput of DTV stadard DVI1.0 compliat Sigal level: Limited Rage 10 bit sigal of its ow specifi catio Durig iput (10 bit twi mode) Sigal level: Limited Rage DVI-D termial DVI-D termial ad AUX termial To DVI-D termial DVI-D cable (optioally available) To DVI output termial To AUX termial 10 bit sigal of its ow specifi catio Durig iput (10 bit sigle mode) Sigal level: Limited Rage DVI-D termial Persoal computer Fig. 1-10j Pi locatio DVI-D termial, AUX termial Pi No. Sigal ame Pi No. Sigal ame 1 DATA2_ 13 DATA3+ 2 DATA V 3 GND 15 DDC_GND 4 DATA4_ 16 HOTPLUG_DET 5 DATA4+ 17 DATA0_ 6 DDC_SCL 18 DATA0+ 7 DDC_SDA 19 GND 8 NC 20 DATA5_ 9 DATA1_ 21 DATA5+ 10 DATA1+ 22 GND 11 GND 23 CLK+ 12 DATA3_ 24 CLK_ 1-32

39 1-11. Iterlock Termial Shield case assembly (1) Iterlock termial Pi locatio Iterlock termial 1. Iterlock Fuctio The iterlock fuctio is eabled by makig the two pis of the iterlock termial ope or short. The followig two patters ca be used for the iterlock fuctio i the applicable serial. Patter 1 Normal: Ope Iterlock: Short Ope/short betwee pi 4 ad pi

40 Patter 2 Normal: Short Iterlock: Ope Ope/short betwee pi 5 ad pi 6 with the pi 3 ad pi 4 shorted state Exteral fa cotrol fuctio This uit mouted a power iterlockig relay for exteral fa cotrol. The trasfer cotact type relay cotrols betwee ormally-ope ad ormally-closed by selectig the pis. The relay for exteral fa cotrol is used for switchig the ON/OFF cotrol sigals for fa. The drivig curret of fa is ot switched. PIN assig Pi Sigal ame Fuctio Pi 7 RELAY1_A make cotact Pi 8 RELAY1_B break cotact Pi 9 RELAY1_C trasfer cotact Operatio table Operatio termial Operatig state STANDBY POWER ON RELAY1_C 5 RELAY1_A ope short RELAY1_C 5 RELAY1_B short ope Cotact specificatio Cotact rated voltage/curret: 25 V DC/500 ma 1-34

41 1-12. Coectig ad Wirig of Exteral Device w Do ot plug the power cord ito the power supply whe performig the followig wirig operatios. Sigal cable wirig Whe coectig this uit or LMT-300 istalled i this uit to exteral device, coect by routig the cable through the hole of the frot side. Hole Exteral device Frot side Fig

42 1-13. Coectig the Power Cord Use the 3-core power cord that satisfy AWG 8, 250 V rated ad 40 A rated. Coect the power cord to the AC IN termial block o the rear side of this uit, referrig the followig procedure. w. Coectio of the mai power ad the electric wirig work should be doe by qualified electricias oly.. Do ot plug the power cord ito the power supply before completig all of the followig coectig operatios. 1. Remove the two screws. 2. Remove the termial block cover with attetio to the two hooks. Hooks Termial block cover Screws Fig. 1-13a 3. Remove the screw, the remove the cable clamp. 4. Remove the screw, the remove the groud termial. Groud termial Screw Cable clamp Screw Fig. 1-13b 1-36

43 5. Pack by solderig the ed of the groud wire. 6. Attach the groud termial removed i step 4 to the groud wire, the fix it with the screw. Groud termial Screw Pack by solderig Groud wire Fig. 1-13c 7. Route the cable through the lower hole of the termial block, the fix each termial by screw. 8. Fix the cable with the cable clamp ad screw. 9. Attach the termial block cover. Groud termial Screws Cable clamp Screw Fig. 1-13d 1-37

44 1-14. Dimesios Frot (Barycetric positio) (Barycetric positio) Left Exhaust 1-38

45 Top (Barycetric positio) Pael for lamp replacig (Barycetric positio) Right Rear * (Optioal les) Refer to List Itake Exhaust Itake Itake (Barycetric positio) Itake Exhaust (Barycetric positio) Bottom Itake AC power cable * LKRL LIST Sigal cable (For the uit fixig) Uit: mm 1-39

46

47 Sectio 2 Adjustmet Adjustmet is performed usig a SRX Cotroller. Refer to Sectio 2-8. for how to use a SRX Cotroller. Perform adjustmet i the procedure below. 1. Istall a SRX Cotroller i a adjustig persoal computer. (Refer to Sectio 2-1.) 2. Perform the optical axis adjustmet of a lamp. (Perform calibratio.) (Refer to Sectio 2-2.) 3. Adjust a les. (Refer to Sectio 2-3.) 4. Perform illumiatio rage adjustmet ad registratio adjustmet. (Perform these adjustmets as required.) (Refer to Sectio 2-4.) 5. Perform the γ adjustmet ad uiformity adjustmet usig the PJ COLOR ADJUSTMENT TOOL. (Refer to Techical Maual of SRX-R220.) 6. Set the illumiace of a scree ad perform color characteristic toe correctio (CSC adjustmet). (Refer to Sectio 2-5.) 7. Adjust the field agle. (Refer to Sectio 2-6.) 8. Set fuctio memory. (Refer to Sectio 2-7.) 2-1

48 2-1. Istallatio of SRX Cotroller Istallatio This uit ca be operated from PC whe the SRX Cotroller is istalled i a persoal computer (PC). For obtaiig of the SRX Cotroller, please cotact your local Soy Sales Office/Service Ceter. Preparatio. PC CPU: Itel Petium M 1.6 GHz or more, ad OS-recommeded RAM capacity: 256 MB or more (512 MB or more recommeded), ad OS-recommeded Commuicatio: RS-232C (10BASE-T/100BASE-T) Graphics mode: XGA (1024 x 768) or higher HDD: Built-i Drive, havig a empty capacity of 10 MB or more CD-ROM drive: Eight times ormal speed or faster OS: Microsoft Widows XP Professioal SP2 (except for x64 Editio). Cable COM: RS-232C cross cable Istallatio 1. Coect each equipmet referrig to Sectio Tur o the power of PC. 3. Copy a SRX Cotroller to ay place of PC. 4. Double-click setup.exe. Fig a 2-2

49 5. Click the [Next] butto. Fig b 6. Cofirm the cotets of the licese agreemet ad click the radio butto for I accept the terms i the licese agreemet. Click the [Next] butto. Fig c 7. Select the folder i which a SRX Cotroller is istalled. Click the [Next] butto if there is o problem i the displayed folder. To chage the folder to save a SRX Cotroller, click the [Chage...] butto ad select the desired folder. Fig d 2-3

50 8. Click the [Istall] butto. Istallatio is started. 9. Check that the widow below is displayed. (Istallatio is completed.) Click the check box for Lauch SRX Cotroller specialized for DC Projector series whe directly startig a SRX Cotroller i this case. Fig e 10. Click the [Fiish] butto. The shortcut of a SRX Cotroller is displayed o the desktop widow Coectio Whe performig the adjustmet usig the RS-232C termial, coect othig to the NETWORK termial of the mai uit. Persoal computer To RS-232C termial To RS-232C termial Coectio cable (Iter-lik cross cable) Fig

51 Startup ad Iitializatio of SRX Cotroller Procedure 1. Coect each equipmet accordig to Sectio Tur o the power switch o the rear of this uit so that it eters the stadby state. (Refer to step 1 of Startup of This Uit.) 3. Double-click Start SRX Cotroller.exe o the desktop widow. 4. Click the COM radio butto from the Coectio meu.. COM selectio: Eter the COM port No. to be used. 5. Select the adjustmet meu (Logi) to be used i a Logi meu. The three adjustmet meus below are available.. User: Ca check the sigal iput to this uit or adjust a image.. Maiteace: Ca set a lamp or adjust a image i details.. Istaller: Ca check ad chage the cotets of settig durig istallatio of logi iformatio or a etwork. 6. Eter the passwords ad click the [OK] butto.. User: A password is ot required.. Maiteace: service. Istallatio: settig Eter the passwords of Maiteace ad Istaller usig lower-case characters. Click this radio butto. Eter the COM port No. to be used. Select User, Maiteace or Istaller. [OK] butto Eter the password. Fig a 2-5

52 Widow of each adjustmet meu Widow example (Logi by User : FUNCTION MEMORY widow) Fig b Widow example (Logi by Maiteace : MAINTENANCE widow) Fig c Widow example (Logi by Istaller : INSTALLATION widow) Fig d 2-6

53 7. Click the INSTALLATION tab. The INSTALLATION widow is displayed. INSTALLATION tab [ON] butto Fig e 8. Set the items i Iteret Settig ad Time Settig meus. (Refer to 5. INSTALLATION widow i Sectio ) 9. Eter the serial code of the lamp bulb to be istalled. (Refer to steps 1 to 4 i Sectio 2-2.) Startup of This Uit Procedure 1. Tur o the power switch o the rear of this uit. (Stadby state) Power switch ON Fig a 2-7

54 2. Start the SRX Cotroller. (Refer to Sectio ) This procedure is commo i the adjustmet meu of User, Maiteace ad Istaller. 3. Click the [ON] butto of POWER. The startup of this uit is completed. [ON] butto Fig b 2-2. Optical Axis Adjustmet of Lamp Procedure 1. Be sure to click the MAINTENANCE tab i the stadby state. 2. Click the [RESET] butto i a LAMP TIMER RESET meu. MAINTENANCE tab [RESET] butto Fig. 2-2a 2-8

55 3. Eter the serial code described i the Operatig Istructios of a lamp bulb i the Serial Code box ad click the [CHECK] butto. m. Be sure to perform i the stadby state. (Refer to step 1 i Sectio ). Eter the serial code with the space ot put. 4. Click the [CLOSE] butto ad close the LAMP INFORMATION widow. 5. Click the [ON] butto of POWER. Eter the serial code. [CHECK] butto [ON] butto Fig. 2-2b [CLOSE] butto 6. Click the FUNCTION MEMORY tab. 7. Set the lamp power to 100% i the LAMP POWER meu to project a image i 100% black. (No sigal coditio) Fig. 2-2c 2-9

56 8. Click the [START] butto i a Lamp Adjust meu o the LAMP INFORMATION widow. The uit eters the lamp adjustmet mode. 9. Wait for five miutes. 10. Whe the uit eters the lamp adjustmet mode, the value of the iteral lumiace sesor is displayed o the status message display. Adjust Z Axis Adjust usig the [+]/[_] butto so that the lumiace value becomes maximum. A lamp bulb is ot istalled whe this uit is shipped from the factory. Therefore, a F34/F35 ADJUST- MENT ERROR message may be displayed o the status message display ad SRX Cotroller at the rear of this uit before this adjustmet is performed. This message disappears whe you press the [Save] butto after Z axis adjustmet. Status message dispaly Fig. 2-2d [START] butto [+], [_] butto [SAVE] butto _ + SAVE START STOP Fig. 2-2e 11. I the same way, adjust the X-axis ad Y-axis directio adjustig screws so that the value of the iteral lumiace sesor becomes maximum. 12. Adjust Z Axis Adjust agai usig the [+]/[_] butto so that the value of the iteral lumiace sesor becomes maximum. 13. Click the [Save] butto. 14. Age this uit for five miutes. 15. Click the [CALIBRATE] butto. Click the [CALIBRATE] butto after at least 10 miutes turig o the lamp. X-axis directio adjustig screw Y-axis directio adjustig screw Fig. 2-2f 2-10

57 Lumiace deterioratio correctio fuctio This uit has a fuctio that makes the output illumiace costat usig a sesor iside equipmet. By pressig the [CALIBRATE] butto, this fuctio provides a iteral sesor ad lamp power output value i the iteral table ad cotrols a lamp power output value so that it becomes the lumiace value set for each fuctio memory. To maitai the precisio of a output value, press the [CALIBRATE] butto about oce a week. This fuctio is eabled whe Lamp Cotrol Mode is set to Lumiace. It is set to Lamp Power i the iitial settig. (Refer to 5. INSTALLATION widow i Fuctio of Each Widow.) 2-3. Les Adjustmet (H Shift, V Shift, Zoom, ad Focus Adjustmets) For further adjustmet, 2-6. Field Agle Adjustmet is required. Procedure 1. Project a test patter o the MAINTENANCE widow. 2. Loose the four bolts securig the projectio les. Isert the flat screwdriver betwee the les bracket ad the les bracket shield ad move the projectio les from side to side to adjust the horizotal positio (H shift) of the image. 3. After H shift adjustmet is completed, tighte the four screws looseed i step 2. Tighte the bolts i the order of to. Projectio les Les bracket Les bracket shield Flat screw driver Bolts Projectio les Bolts Fig. 2-3a 2-11

58 4. Ope the adjustmet lid. 5. Tur the cotrol kob of this uit to move the les up ad dow for adjustig the vertical positio (V shift) of a image. 6. Adjust the zoom ad focus usig the [+]/[_] buttos i the Les Cotrol meu o the FUNCTION MEMO- RY widow. (Refer to 2. FUNCTION MEMORY widow i Fuctio of Each Widow.) Projectio les Cotrol kob Adjustmet lid Fig. 2-3b Set the V shift amout withi 1/2 scree. If it exceeds 1/2 scree, the zoom is chaged, the image positio may ot be positioed at same place. Check if the V shift amout exceeds 1/2 scree i the followig procedure. Whe the V shift amout exceeds 1/2 scree, perform the adjustmet. I the case that the V shift is lowered. How to Check. Whe the image is expaded by zoom, the upper ed of image positio is lowered. Effective area of les Effective area of les Ceter of les Image Image Fig. 2-3c 2-12

59 How to Adjust. Adjust the V shift so that the upper ed of image positio remais uchaged whe the image is expaded by zoom. Effective area of les Effective area of les Ceter of les Image Image Fig. 2-3d 2-4. Illumiatio Area Adjustmet ad Registratio Adjustmet Illumiatio Area Adjustmet If there is ay deviatio of illumiatio rage whe istallig the uit, perform adjustmet i the followig procedure. The adjustmet caot be correctly performed with the filter cover ope because the filter cover switch sesor fuctio operates. Before startig the adjustmet, be sure to close the filter cover after removig the pael duct covers 1 ad the pael duct covers 2. Frot side Filter cover Filter cover switch Fig a 2-13

60 Procedure 1. Remove the pael (U7) block assembly. (Refer to Sectio ) 2. Remove the pael (U2) block assembly. (Refer to Sectio ) 3. Remove the filter. 4. Remove the five screws. Filter (ceter portio) Frot side Screws Fig b 2-14

61 5. Ope the filter cover i the directio of the arrow. 6. Remove the two screws, the remove the pael duct cover 2 (upper). 7. Remove the two screws, the remove the pael duct cover 1 (upper). 8. Remove the pael duct cover 2 (lower) ad the pael duct cover 1 (lower) i the same procedure as steps 6 ad Close the filter cover, the secure it with the screw. Frot side Pael duct cover 2 (upper) Pael duct cover 2 (lower) Filter cover Pael duct cover 1 (upper) Screws Pael duct cover 1 (lower) Screws Filter cover Secure with the screw. Fig c 2-15

62 10. Start the SRX Cotroller. (Refer to Sectio ) 11. Click the FUNCTION MEMORY tab. FUNCTION MEMORY widow LENS CONTROL meu LAMP POWER meu Fig d MAINTENANCE widow TEST PATTERN meu Fig e 2-16

63 12. Set Lamp Power to 50% immediately after the lamp is lit. 13. Project the white image o the scree usig Test Mode 1 i the TEST PATTERN meu o the MAINTENANCE widow. If it is difficult to observe the left, right, top ad bottom edges of the white image because it is iterrupted by the black curtai ad so o, reduce the white image size usig the zoom so that its edges ca be viewed clearly. Adjust the zoom i LENS CONTROL o the FUNCTION MEMORY widow. I the case of out-offocus, adjust it i the same way. (Refer to 2. FUNCTION MEMORY widow i Fuctios of Each Widow.) 14. Perform steps 15 to 17 immediately after step 13 is fiished. 15. Observe the left, right, top ad bottom edges of the scree precisely. 16. Check the deviatio of illumiatio rage (colored area aroud the white image). If there is a area colored by cya, loose the adjustig plate fixig screws of portio A i the illustratio, ad tighte them after adjustmet. 17. If there is a area colored by mageta/yellow, loose the adjustig plate fixig screws of portio B i the illustratio, ad tighte them after adjustmet. Portio A Portio B Adjusts the left ad right of the white image by parallel movemet. Adjusts the top ad bottom of the white image by rotatioal movemet. Fig f Registratio Adjustmet Perform adjustmet referrig to 4. MAINTENANCE widow i Fuctio of Each Widow if registratio is out of positio. 2-17

64 2-5. Scree Illumiace Settig ad Color Space Coversio (CSC Adjustmet) Before settig fuctio memory, set the illumiace o the scree ad correct the color space, with the uit istalled. Color space coverter The color space coverter ca correct the color characteristics of this uit (709, Virtual White ad DCDM) for each color reproductio rage. Correctio of color space 709 Procedure 1. Display the FUNCTION MEMORY widow of the SRX Cotroller. (Refer to Sectio ) 2. Click the radio butto of Iput A i the INPUT CONTROL meu. INPUT CONTROL meu Fig. 2-5a 3. Display the MAINTENANCE widow. (Refer to Sectio ) COLOR SPACE CONVERTER meu [ADJUST] butto Fig. 2-5b 2-18

65 4. Click the [ADJUST] butto i the COLOR SPACE CONVERTER meu. The COLOR SPACE widow is displayed. TEST PATTERN SELECT meu Fig. 2-5c 5. Select Gray 10 i TEST PATTERN SELECT meu. A test patter of Gray 10 is displayed. 6. Click the FUNCTION MEMORY tab. The FUNCTION MEMORY widow is displayed. 7. Adjust usig the [+]/[_] butto of the lamp power so that the illumiace o the scree is approximately 16 ft-l (the illumiace to be set + approximately 2 ft-l). 8. Select 6500 i Color Temp of the COLOR meu. Whe the item is ot a available, iput a video sigal. 9. Select 709 i Color Space of COLOR meu. Whe the item is ot a available, iput a video sigal. LAMP POWER meu COLOR meu Fig. 2-5d Each value is automatically displayed i the Target Color Gamut colum of the COLOR SPACE widow o the MAINTENANCE tab. Moreover, referece white poit targets x ad y ad lumiace level Y are projected automatically. 2-19

66 10. Click the MAINTENANCE tab. 11. Click the [ADJUST] butto i a COLOR SPACE CONVERTER meu. The COLOR SPACE widow is displayed. COLOR SPACE meu [APPLY] butto TEST PATTERN SELECT meu Fig. 2-5e [CALC] butto [RESET] butto Iput Color Measuremet colum 12. Select 709 i the COLOR SPACE meu. Whe COLOR SPACE is ot available, iput a video sigal. 13. Click the [RESET] butto. A color space fuctio is set to OFF, ad the characteristics of this uit ca be measured. 14. Project Gree-1, Blue-1, ad Red-1, respectively i the TEST PATTERN SELECT meu ad measure x, y, ad lumiace level Y. 15. Select Gray 8 accordig to the referece white poit. A test patter of Gray 8 is displayed. 16. Measure x, y ad lumiace level Y. 17. Eter the measuremet result i step 14 ito the Iput Color Measuremet colum. 18. Click the [CALC] butto. 19. Cofirm that the differeces of all umeric values are less tha? Whe there is a item i which the differeces of the umeric value is?0.002 or more, repeat the steps 14 to Click the [APPLY] butto. 21. Retur the settig before adjustig. Whe the CSC adjustmet is performed, the lumiace is lowered by approximately 2 ft-l. Therefore, adjust the lamp power i the LAMP POWER meu to obtai the required lumiace agai. 2-20

67 Adjustmet of color space Virtual White The adjustmet ca be performed i the followig two methods. Procedure Adjustmet usig iteral test patter The adjustmet ca be performed usig the iteral test patters; Red-1, Gree-1, Blue-1 ad Gray Start the SRX Cotroller. (Refer to Sectio ) 2. Click the MAINTENANCE tab of the SRX Cotroller. The MAINTENANCE widow is displayed. COLOR SPACE CONVERTER meu [ADJUST] butto Fig. 2-5f 3. Click the [ADJUST] butto i the COLOR SPACE CONVERTER meu. The COLOR SPACE widow is displayed. COLOR SPACE meu [APPLY] butto TEST PATTERN SELECT meu [RESET] butto Iput Color Measuremet colum Fig. 2-5g [CALC] butto [TARGET RECALL] butto 2-21

68 4. Select the Gray-10 i the TEST PATTERN SELECT meu. 5. Measure the lumiace of scree ad adjust the lamp power i the LAMP POWER meu o the FUNCTION MEMORY widow so that the lumiace is 16 ft-l. After adjustmet, the lumiace is lowered by approximately 2 ft-l. 6. Select Virtual White i the COLOR SPACE meu. Whe COLOR SPACE is ot available, iput a video sigal. 7. Check the W values of Target Color Gamut is x = 0.319, y = Whe the W values are mismatch, click the [TARGET RECALL] butto. 9. Click the [RESET] butto first, ad the click the [APPLY] butto. 10. Select Red-1, Gree-1, Blue-1 ad Gray-8 respectively i the TEST PATTERN SELECT meu. The, measure x ad y values respectively. 11. Eter the x ad y values i Iput Color Measuremet i the COLOR SPACE meu. 12. Click the [CALC] butto first, ad the click the [APPLY] butto o the COLOR SPACE widow. 13. Select Red-1, Gree-1, Blue-1 ad Gray-8 respectively i the TEST PATTERN SELECT meu. The, measure the x ad y values respectively ad compare the results with the followig specificatios withi a error rage of x y Red Gree Blue Gray If the specificatios are ot satisfied, perform steps 4, 5, ad 9 to 12 agai. 14. Select the Gray-10 i the TEST PATTERN SELECT meu. 15. Click the FUNCTION MEMORY tab. The FUNCTION MEMORY widow is displayed. 16. Adjust the lamp power i the LAMP POWER meu so that the lumiace is 14 ft-l. I this procedure, the lumiace is ot correctly 14 ft-l. Whe the correct lumiace is required, iput Gray 10 of the SONY color patch by LMT-300, ad adjust the lamp power. 2-22

69 Adjustmet usig Soy Color Patch 1. Copy the Soy color patch files (DPPJ07-080_1.zip to DPPJ07-080_4.zip) i PC. For obtaiig, please cotact your local Soy Sales Office/Service Ceter. 2. Create the Soy_Color_Patch folder ad move all files obtaied by decompressig the zip file to the Soy_Color_Patch folder. (The files havig the extesio of.xml ad.mxf) 3. Import it i the same way as the ormal DCP cotets. 4. Start the SRX Cotroller ad the Scree Maagemet Cotroller. 5. Click the FUNCTION MEMORY tab of the SRX Cotroller. The FUNCTION MEMORY widow is displayed. INPUT CONTROL meu PICTURE CONTROL meu LAMP POWER meu Fig. 2-5h 2-23

70 6. Click the Iput C (LMT-300) radio butto i the INPUT CONTROL meu. 7. Set Cotrast to 90 ad Bright to 50 i the PICTURE CONTROL meu. 8. Reproduce the Gray 10 of Soy Color Patch sigal from LMT-300 by Scree Maagemet Cotroller. 9. Click the FUNCTION MEMORY tab of the SRX Cotroller. The FUNCTION MEMORY widow is displayed. 10. Measure the lumiace of scree ad adjust the lamp power i the LAMP POWER meu so that the lumiace is 16 ft-l. After the CSC adjustmet, the lumiace is lowered by approximately 2 ft-l. 11. Click the MAINTENANCE tab of the SRX Cotroller. The MAINTENANCE widow is displayed. COLOR SPACE CONVERTER meu [ADJUST] butto Fig. 2-5i 2-24

71 12. Click the [ADJUST] butto i the COLOR SPACE CONVERTER meu. The COLOR SPACE widow is displayed. COLOR SPACE meu [APPLY] butto Iput Color Measuremet colum Target Color Gamut colum [RESET] butto [CALC] butto Fig. 2-5j 13. Select Virtual White i the COLOR SPACE meu. Whe COLOR SPACE is ot available, iput a video sigal. 14. Click the [RESET] butto first, ad the click the [APPLY] butto. 15. Chage the W values of Target Color Gamut to x = 0.314, ad y = Reproduce the Red-1, Gree-1, Blue-1 ad Gray-8 of Soy Color Patch sigal from LMT-300 by Scree Maagemet Cotroller. The, measure the x ad y values respectively. 17. Eter the x ad y values i Iput Color Measuremet o the COLOR SPACE widow. 18. Click the [CALC] butto first, ad the click the [APPLY] butto. 19. Reproduce the Red-1, Gree-1, Blue-1 ad Gray-8 of Soy Color Patch sigal from LMT-300 by Scree Maagemet Cotroller. The, measure the x ad y values respectively, ad compare the results with the followig DCI specificatios withi a error rage of x y Red Gree Blue Gray If the specificatios are ot satisfied, perform steps 9, 10, ad 14 to 18 agai. 20. Reproduce Gray-10 from LMT-300 ad adjust the lamp power i the LAMP POWER meu so that the lumiace is 14 ft-l. If the lumiace of 16 ft-l or 14 ft-l is ot esured, set the lamp power settig to 100% ad perform adjustmet i the maximum lumiace state. 2-25

72 Adjustmet of color space DCDM The adjustmet ca be performed usig the iteral test patters; Red-1, Gree-1, Blue-1 ad Gray-8. Procedure 1. Start the SRX Cotroller. (Refer to Sectio ) 2. Click the MAINTENANCE tab of the SRX Cotroller. The MAINTENANCE widow is displayed. COLOR SPACE CONVERTER meu [ADJUST] butto Fig. 2-5k 3. Click the [ADJUST] butto i the COLOR SPACE CONVERTER meu. The COLOR SPACE widow is displayed. COLOR SPACE meu [APPLY] butto TEST PATTERN SELECT meu [RESET] butto Iput Color Measuremet colum Fig. 2-5l [CALC] butto [TARGET RECALL] butto 2-26

73 4. Select the Gray-10 i the TEST PATTERN SELECT meu. 5. Measure the lumiace of scree ad adjust the lamp power i the LAMP POWER meu so that the lumiace is 16 ft-l. After adjustmet, the lumiace is lowered by approximately 2 ft-l. 6. Select DCDM i the COLOR SPACE meu. Whe COLOR SPACE is ot available, iput a video sigal. 7. Check the W values of Target Color Gamut is x = 0.314, y = Whe the W values are mismatch, click the [TARGET RECALL] butto. 9. Click the [RESET] butto first, ad the click the [APPLY] butto. 10. Select Red-1, Gree-1, Blue-1 ad Gray-8 respectively i the TEST PATTERN SELECT meu. The, measure x ad y values respectively. 11. Eter the x ad y values i Iput Color Measuremet i the COLOR SPACE meu. 12. Click the [CALC] butto first, ad the click the [APPLY] butto i the COLOR SPACE widow. 13. Select Red-1, Gree-1, Blue-1 ad Gray-8 respectively i the TEST PATTERN SELECT meu. The, measure the x ad y values respectively ad compare the results with the followig specificatios withi a error rage of x y Red Gree Blue Gray If the specificatios are ot satisfied, perform steps 4, 5, ad 9 to 12 agai. 14. Select the Gray-10 i the TEST PATTERN SELECT meu. 15. Click the FUNCTION MEMORY tab. The FUNCTION MEMORY widow is displayed. 16. Adjust the lamp power i the LAMP POWER meu so that the lumiace is 14 ft-l. I this procedure, the lumiace is ot correctly 14 ft-l. Whe the correct lumiace is required, iput Gray 10 of the SONY color patch by LMT-300, ad adjust the lamp power. CSC adjustmet for virtual white The D61 WP (White Poit) of DCDM stadard specified by DCI SPEC is cosiderably gree-tiged. Some people i the film idustry recommed D65 or D55 WP. However, whe the software created by D65 or D55 WP is istalled i the display adjusted by DCI SPEC, some colors ru out of color space causig a clippig problem. To solve this problem, Virtual White is proposed. Its chromaticity rage is the same as DCDM; WP x=0.319, y= Also, the data for realizig 14 ft-l is slightly chagig. By this, the clippig problem does ot occur i ay of D65, D61 ad D55. If Virtual White is used for adjustmet, there is o problem i the DCI SPEC sigal. For this uit, Virtual White ca be selected i COLOR SPACE. 2-27