Eltako The Wireless Building

Transcription

1 YEARS OF INNOVATION Eltako The Wireless Building Reliable, very reasonable and comfortable Products and prices 2015 Switching on the future

2 Eltako The Wireless Building Introduction Unlimited fl exibility and convenience in building services The wireless network with the revolutionary wireless sensors without battery or wire in Eltako wireless pushbuttons and with innovative Eltako wireless switchgear. Wireless networks only function well with batteryless wireless modules. They generate their own power supply of approx. 50μWs when a pushbutton is operated, therefore they require no external power supply. They transmit ultra short interference-proof signals in the 868MHz band with a range of up to 100 meters in halls. They are integrated in Eltako wireless pushbuttons that are only 11mm or 16mm high. These are screwed directly to the wall, bonded to glass or on furniture, and they can also be screwed conventionally to a socket box. Maintenance-free all inclusive. Eltako wireless pushbuttons without battery or wire reduce the electrosmog load since they emit high-frequency waves that are 100 times weaker than conventional light switches. There is also a significant reduction in low-frequency alternating fields since fewer power cables need to be installed in the building. Passive and active wireless sensors Receivers + switchgear (actuators) Accessories The batteryless wireless pushbuttons comprise an wireless module. It is available with inner frame dimensions of 55x55mm (standard), 60x60mm (Swiss design), 63x63mm (flat pushbutton) and in E-Design. They are combinable with the frames of many other manu facturers. Using the same system, we manufacture flat pushbuttons, mini pushbuttons, hand- held transmitters, remote controls, pull switches, hotel key card switches and window/door contacts. With its own solar cell power supply, we manufacture window/door contacts, motion/brightness sensors, bright ness sensors, twilight sensors, humidity temperature sensors, temperature controllers and temperature sensors. Other sensors require an external power supply with mains voltage, 12V switch mode power supply unit or battery. For centralised wireless systems with DIN rail mounted actuators, we manufacturer wireless antenna modules which are linked to the associated actuators over the Eltako RS485 bus in the switchboard or distribution box. For decentralised wireless systems we manufacture wireless actuators for the 55mm switch socket and for mounting, e.g. in false ceilings with integrated wireless receivers and internal antennas. For difficult reception conditions, we manufacture 2-level wireless repeaters - as well as connectors for external antennas. For metal switching cabinets, the standard antenna of the wireless antenna module and the wireless transmitter modules can be replaced by an external antenna with a magnetic base as required. Reduced costs for many installations in new buildings and for expansions. Eltako Wireless Building can bring you savings over conventional solutions since it cuts out the need to lay cables. Of course, this also depends on the size of the building. However, you always win through greater convenience and flexibility. II

3 Eltako The Wireless Building Contents Passive wireless sensors The new E-Design, the shapes and colours of the pushbuttons and frames, the Q Design, pushbuttons without battery or wire, noise less pushbuttons, pushbutton lighting, frames, blind covers, socket outlets, wireless pushbutton encryption rocker, rockers laser engraved, remote controls, hand-held transmitters, mini hand-held transmitters, window/door contacts, position switches, window handles, card switch and pull switch Active wireless sensors 2 Transmitter modules, sater sensor, smoke alarm, motion/brightness sensors, brightness sensors, twilight sensor, humidity temperature sensors, thermo clock/hygrostat with small actuators, temperature controllers, temperature sensors, CO 2 sensor, timer and teach-in list sensors/actuators Series 14 DIN rail mounted devices central installation 3 Antenna module, gateways, GSM module, PC-Tool, impulse switches, relais, sunshade switches, dimmer switches, controller for electronic ballast 1-10V, time relay, staircase off-delay timer, mains disconnection relay, Heating/cooling relay, fan relay, timer, multifunction sensor relay, energy meter concentrator, data gateway, energy meters, repeater and telegram duplicator. 1 The remote switch system FTS14 with and without Wireless Building Impulse switch for shading element and roller shutters with central control for low voltage for connection to the central control gateway Bus 4-way pushbutton and pushbutton bus coupler to connect to pushbutton gateways 4 Switching and dimming actuators for installation decentralised installation 5 Electronic impulse switches, relays, light controller, universal dimmer switches, shading element switch, staircase off-delay timer, time relay, heating/cooling relays, mains dis connection relay, socket outlet switches and gong module FME14 The modular single room control with wireless actuators in heating circuit distributors and with wireless room temperature controllers 6 Smart Metering - smart energy metering, visualisation and display Energy consumption indicators, visualisation software GFVS-Energy, energy meter transmitter modules, single-phase energy meter transmitter modules and three-phase energy meter 7 The blue wireless network in the building Server-assisted building monitoring, control and visualisation. Secure data management with Eltako GFVS-Safe II and the factory installed Eltako Wireless Building Visualisation and Control Software GFVS V Z Accessories wireless pushbutton lighting, gateways, repeater, switching power supply units, Powernet phase coupler, wireless antennas, network camera, level meter and socket strips Technical data, teach-in list, distances and contents of Eltako wireless telegrams T Index, abbreviations of functions and terms of delivery S III

4 Eltako The Wireless Building Pictograms The performance of our devices has become so complex that we have devised pictograms to depict technical features of particular importance. Minimized standby loss of electronic devices supports international efforts to reduce energy consumption. 98% of the devices produced by ELTAKO have a standby loss of less than 0.8 watt. Numerous pushbuttons, sensors and transmitter modules work without stand-by loss. Bistable switching relays help electronic switchgear to reduce heating and current consumption. This prolongs lifetime and reduces or avoids standby loss. After installation the short automatic synchronization in the Off position is carried out, partly at initial operation. Bidirectional wireless expands the functions of the wireless actuators by another dimension: every change in state and incoming central control telegrams are confirmed by wireless telegram. This wireless telegram can be taught-in in other actuators, the GFVS Software and in universal displays. In addition, a repeater function can partially be enabled in these actuators to reach other actuators that are located far away from the wireless source. The Eltako RS485 bus connects the wireless antenna modules FAM14, FEM and/or pushbutton input modules FTS14EM with the RS485 bus actuators in the switchboard or distribution box. It is an often used and very safe 2-wire bus. Zero passage switching of the mains voltage sinusoidal wave prolongs contact lifetime. This provides very high switching capacities and the shallow current flow curve protects the connected consumers. This prolongs in particular the lifetime of energy saving lamps ESL. With the patented Eltako Duplex technology (DX) the normally potential-free contacts can still switch in zero passage when switching 230V AC 50Hz and therefore drastically reduce wear. Simply connect the neutral conductor to the terminal (N) and L to the contact input terminal (L). This gives an additional standby consumption of only 0.1 Watt. Universal dimmer for R, L and C loads. Our universal dimmer switches recognize automatically the connected load and adjust their dimmer function accordingly. Other dimmers have to be replaced when luminaires with different kind of loads will be used later on. Only universal dimmer switches with the added ESL marking and added LED marking have the associated comfort settings. SSR Solid state relays operate noiseless, switch in zero passage and are very durable, even at high switching frequency. Encrypted wireless system. The internet transmissions of the GFVS software to smartphones and M2M communications are generally highly encrypted. Many wireless pushbuttons can be taught-in encrypted in actuators of the Series 61 and 71 as well as the FAM14. Only a trained electrician may install our devices, otherwise there is a risk of fire or electric shock. It is therefore prohibited to sell to other customers for this reason otherwise the risk passes to the seller. IV Special models and non-standard control voltages are only supplied ex works. Any return is excluded. Subject to change! The product descriptions on the internet are valid only for newly manufactured devices at that time. Also this print-catalogue is only a snap-shot. Older and newer devices might differ from them. Therefore, only the operation instructions enclosed with the devices are binding. Terms of delivery see page S-3. All articles are available with Declarations of Conformity that document compliance of the devices with the Low-Voltage Directive 2006/95/EC and/or the EMC Directive 2004/108/EC. The -mark is affi xed to the devices and the packaging. All articles comply with EU Directives 2011/65/EU (RoHS) and 1907/2006/EC (REACH) and contain no substances that are on the candidate list. Supply and invoice only through wholesalers.

5 Eltako The Wireless Building Passive Wireless Sensors 1 The E-Design 1-0 Pushbuttons without wire F4T55B 1-4 The shapes and colours of the pushbuttons FT4F, FT55 and FFT55Q as well as frames 1-15 The Q Design. Single, double and triple frames plastic, glass and stainless steel 1-16 Flat pushbuttons FFT55Q and wireless pushbuttons without battery or wire FT4F, FT55 and as well as 1-19 wireless mini pushbuttons FMT55 Frames R, blind cover BL and socket outlet DSS 1-24 Wireless pushbuttons FT55R 1-28 Wireless pushbuttons FT4CH, Swiss Design 1-29 Wireless pushbutton encryption rocker FTVW 1-30 Rockers and double rockers laser engraved 1-31 Universal remote control UFB and infrared converter FIW 1-34 Remote control FF8 and FFD with display backlighting 1-37 Hand-held transmitters FHS8 and FHS Mini hand-held transmitters FMH8, FMH2, FMH4 and FMH1W 1-41 Window/door contact FTK and FTKB with batteries 1-46 Wireless sensors with energy generator, window/door contact FTKE and position switches FPE 1-48 Wireless encryption plug FVST 1-49 Window handles FHF from Hoppe (SecuSignal) 1-50 Wireless sensor hotel key card switches FKF65 and FKC Wireless sensor pull switch FZS Switching on the future

6 The E-Design 1-0 Wireless pushbuttons, bus pushbuttons and short-stroke pushbuttons with single E-design frames, pure white glossy Passive sensors: pushbuttons 63x63mm integrated in pushbutton frames 65x65mm F4T65 wireless 4-way pushbutton with EnOcean wireless module PTM215, W+DW F1FT65 wireless 1-way flat pushbutton with EnOcean wireless module PTM335 F4T65B wireless 4-way pushbutton with battery (button cell), W+DW F4FT65B wireless flat pushbutton with battery (button cell), W+DW B4T65 bus 4-way pushbutton with bus connection to FTS14TG, W+DW B4FT65 bus 4-way flat pushbutton with bus connection to FTS14TG, W+DW K4T65 4-way short-stroke pushbutton K4FT65 4-way flat short-stroke pushbutton F4T65 F4T65 F1FT65 F4T65B/F4FT65B F4T65B/F4FT65B Wireless 4-way pushbutton with rocker without battery or wire Wireless 4-way pushbutton with double rocker without battery or wire Wireless 1-way flat pushbutton without battery or wire Wireless 4-way pushbutton with rocker and battery Wireless 4-way flat pushbutton with rocker and battery Wireless 4-way pushbutton with double rocker and battery Wireless 4-way flat pushbutton with double rocker and battery B4T65 B4FT65 Bus 4-way pushbutton with rocker Bus 4-way flat pushbutton with rocker Switching on the future B4T65 B4FT65 Bus 4-way pushbutton with double rocker Bus 4-way flat pushbutton with double rocker K4T65 K4FT65 4-way short-stroke pushbutton with rocker 4-way short-stroke flat pushbutton with rocker K4T65 K4FT65 4-way short-stroke pushbutton with double rocker 4-way short-stroke flat pushbutton with double rocker

7 The E-Design Single, double and triple frames and flat frames for E-design sensors and new inserts 1-1 Frames single 84x84x13.5mm double 84x155x13.5mm triple 84x226x13.5mm Flat frames single 84x84x8.5mm double 84x155x8.5 mm triple 84x226x8.5 mm R1E, RF1E Single frame 84x84x13.5mm Single flat frame 84x84x8,5mm R2E, RF2E Double frame 84x155x13.5mm Double flat frame 84x155x8.5mm R3E, RF3E Triple frame 84x226x13.5mm Triple flat frame 84x226x8.5mm R1E RF1E BLA65 BLA65F Side view pushbutton with frame 16 mm high Side view flat pushbutton with flat frame 11mm high Blind cover for R1E, R2E and R3E Blind cover for RF1E, RF2E and RF3E TAE65/3 TAE65F/3 TV65/2 TV65F/2 TV65/3 TV65F/3 UAE65/2 UAE65F/22 DSS65 DSS65F S65 DS S65F Cover for 3-way telecommunications access unit (TAE) for frames and flat frames 2-hole cover for TV/RF aerial socket for frames and flat frames 3-hole cover for TV/RF/SAT aerial sockets for frames and flat frames Cover for 2-hole UAE/IAE (ISDN) and network sockets for frames and flat frames German Fused Safety Socket DSS with socket outlet front for frames and flat frames

8 Wireless Sensor without battery or wire Wireless Pushbutton in E-Design F4T F4T65-wg Wireless pushbutton with rocker Wireless pushbutton with double rocker Wireless pushbutton for single mounting 84x84x16mm or mounting into the E-design switching system. Generates the power for wireless telegrams itself when the button is pressed, therefore there is no connecting wire and no standby loss. The scope of supply comprises the frame R1E, a flat rocker, a flat double rocker (all same colour), an attachment frame, a mounting base, the wireless module and one adhesive foil. Wireless pushbuttons with one rocker can transmit two evaluable signals: press rocker up and press rocker down. Wireless pushbuttons with double rocker can transmit four evaluable signals: press two rockers up or down. The mounting base can be screwed onto a flat surface or glued to the wall, on glass or on furniture using the enclosed adhesive foil. Use the sleeves in the 55mm socket box for screw mounting. Then the wireless switch lighting FTB can be snapped into the mounting plate from the rear. The double rocker is snapped onto the wireless module at the factory. If the double rocker is replaced by the large rocker, remove the rocker halves by pulling off to the front. Do not bend towards the middle. Then snap the large rocker so that the markings 0 and I on the back line up with the same markings on the wireless module. Adhesion: First adhere the set comprising the mounting base, frame and attachment frame with the latches pointing at the top and bottom. Then snap on the set comprising the wireless module and rocker - with the marking 0 on the back always pointing up. Before screwing, remove the mounting base from the frame and the attachment frame. To do this, press the latches on the mounting base outwards. Then screw the mounting base with the latches at top and bottom, snap on the frame with the attachment frame and snap on the set comprising the wireless module and rocker with the marking 0 on the back always pointing to the top. We recommend stainless-steel countersunk screws 2.9x25mm, DIN 7982 C, for screw connections. Both with rawl plugs 5x25mm and with 55mm switch boxes. See chapter Z: 'Accessories'. The wireless module integrated in the wireless pushbutton can be taught-in encrypted as described in the operating instructions in all encryptable actuators of the Series 61 and Series 71 as well as the FAM14. This requires the FTVW wireless pushbutton encryption rocker on page Encryptable actuators bear the pictogram. Rockers and double rockers laser engraved page F4T65-wg Wireless pushbutton without battery or wire, pure white glossy EAN ,50 /pc.

9 Wireless Sensor without wire Wireless Pushbutton in E-Design F4T65B F4T65B-wg Wireless pushbutton with rocker Wireless pushbutton with double rocker Wireless pushbutton for single mounting 84x84x16mm or mounting into the E-design switching system. Whisper quiet and with button cell. The scope of supply comprises a mounting base with snapped-on electronics, a frame R1E, a rocker and a double rocker. Wireless pushbuttons with one rocker can transmit two evaluable signals: press rocker up and press rocker down. Wireless pushbuttons with double rocker can transmit four evaluable signals: press two rockers up or down. The mounting base can be screwed onto a flat surface or glued to the wall, on glass or on furniture using the enclosed adhesive foil. Use the sleeves in the 55mm socket box for screw mounting. Snap the large rocker so that the markings 0 and I on the back line up with the same markings on the wireless module. Installation only on a level surface: Screw on or glue mounting plate. First snap on the electronics, then the frame and remove the battery insulator. When you fit the rocker, the 0 mark on the rear must always be on top. We recommend stainless-steel countersunk screws 2.9x25mm, DIN 7982 C, for screw connections. Both with rawl plugs 5x25mm and with 55mm switch boxes. See chapter Z: 'Accessories'. All you need to do to change the CR2032 button cell is remove the rocker. The electronics integrated in the wireless pushbutton can be taught-in encrypted as described in the operating instructions in all encryptable actuators of the Series 61 and Series 71 as well as the FAM14. Encryptable actuators bear the pictogram. 1-3 Rockers and double rockers laser engraved page F4T65B-wg Wireless pushbutton without wire, pure white glossy EAN ,20 /pc.

10 Wireless Sensors Pushbuttons without wire F4T55B 1-4 F4T55B Wireless pushbutton with rocker Wireless pushbutton with double rocker Wireless pushbutton for single mounting 80x80x15mm or mounting in the 55mm switch system. Whisper quiet and with button cell. The scope of supply comprises a mounting base, an attachment frame with snapped-on electronics, a frame R1, a rocker and a double rocker. Wireless pushbuttons with one rocker can transmit two evaluable signals: press rocker up and press rocker down. Wireless pushbuttons with double rocker can transmit four evaluable signals: press two rockers up or down. The mounting base can be screwed onto a flat surface or glued to the wall, on glass or on furniture using the enclosed adhesive foil. Use the sleeves in the 55mm socket box for screw mounting. Snap the large rocker so that the markings 0 and I on the back line up with the same markings on the wireless module. Installation only on a level surface: Screw on or glue mounting plate. First snap on the frame and then clip on the attachment frame with the electronics. Insert the enclosed button cell in the battery compartment with the + marking pointing upwards. When you fit the rocker, the 0 mark on the rear must always be on top. We recommend stainless-steel countersunk screws 2.9x25mm, DIN 7982 C, for screw connections. Both with rawl plugs 5x25mm and with 55mm switch boxes. See chapter Z: 'Accessories'. All you need to do to change the CR1632 button cell is remove the rocker. The electronics integrated in the wireless pushbutton can be taught-in encrypted as described in the operating instructions in all encryptable actuators of the Series 61 and Series 71 as well as the FAM14. Encryptable actuators bear the pictogram. Rockers and double rockers laser engraved page F4T55B-ws Wireless pushbutton 55x55mm without wire, with battery white Wireless pushbutton 55x55mm without wire, with battery pure white Wireless pushbutton 55x55mm without wire, with battery pure white glossy Wireless pushbutton 55x55mm without wire, with battery black Wireless pushbutton 55x55mm without wire, with battery anthracite Wireless pushbutton 55x55mm without wire, with battery coated/aluminium paint EAN ,20 /pc. F4T55B-rw EAN ,20 /pc. F4T55B-wg EAN ,20 /pc. F4T55B-sz EAN ,20 /pc. F4T55B-an EAN ,20 /pc. F4T55B-al EAN ,40 /pc.

11 Bus Pushbutton in E-Design B4T65 B4T65 Bus switch with rocker Bus switch with double rocker Bus pushbutton for single mounting 84x84x16mm or mounting into the E-design switching system. For connection to FTS14TG pushbutton gateway. Only 0.2 watt standby loss. The scope of supply comprises a mounting base with snapped-on electronics, a frame R1E, a rocker and a double rocker. The double rocker permits entry of 4 evaluable signals, but the rocker allows only 2 signals. At the rear, a 20cm long red/black bus line is routed externally. Red terminal to BP, black to BN of a pushbutton gateway FTS14TG. Up to 30 bus switches and/or FTS61BTK pushbutton bus couplers can be connected to terminals BP and BN of an FTS14TG pushbutton gateway. The permitted maximum line length is 150m. The line length is extendable to 250m by fitting an RLC element to the furthest B4. A voltage of 29V DC is supplied to the connected B4 over a 2-wire pushbutton bus which is also used for data transfer. Confirmation telegrams from actuators are displayed by 4 resp. 2 yellow LEDs when the actuator IDs are entered by the PCT14 in the ID table of the FTS14TG. Use the sleeves in the 55mm socket box for screw mounting. Installation: Screw on mounting plate. First snap on the electronics, then the frame. When you fit the rocker, the 0 mark on the rear must always be on top. We recommend stainless-steel countersunk screws 2.9x25mm, DIN 7982 C, for screw connections. Both with rawl plugs 5x25mm and with 55mm switch boxes. See chapter Z: 'Accessories'. 1-5 Rockers and double rockers laser engraved page RLC element Range extension for B4T65/B4FT65 EAN ,80 /pc. B4T65-wg Bus pushbutton in E-Design, pure white glossy EAN ,80 /pc.

12 Wireless Sensor without battery or wire Wireless Flat Pushbutton in E-Design F1FT F1FT65-wg Wireless fl at pushbutton with rocker Wireless flat pushbutton for single mounting 84x84x11mm or mounting into the E-design switching system. Generates the power for wireless telegrams itself when the button is pressed, therefore there is no connecting wire and no standby loss. The scope of supply comprises the flat frame RF1E, a rocker, a mounting base, the wireless module and one adhesive foil. Wireless flat pushbuttons with one rocker can send an analysable signal. Press the bottom of the rocker near the mark. The mounting base can be screwed onto a flat surface or glued to the wall, on glass or on furniture using the enclosed adhesive foil. Use the sleeves in the 55mm socket box for screw mounting. Then the wireless switch lighting FTB can be snapped into the mounting plate from the rear. Before screwing on the device, remove the rocker and remove the frame from the mounting plate. Then screw on the mounting base - with the 'top' marking pointing upwards. Snap the frame and rocker back in. We recommend stainless-steel countersunk screws 2.9x25mm, DIN 7982 C, for screw connections. Both with rawl plugs 5x25mm and with 55mm switch boxes. See chapter Z: 'Accessories'. The wireless module integrated in the wireless flat pushbutton can be taught-in encrypted as described in the operating instructions in all encryptable actuators of the Series 61 and Series 71 as well as the FAM14. This requires the wireless encryption plug FVST on page Encryptable actuators bear the pictogram. Rockers laser engraved page F1FT65-wg Wireless fl at pushbutton without battery or wire, pure white glossy EAN ,90 /pc.

13 Wireless Sensor without wire Wireless Flat Pushbutton in E-Design F4FT65B F4FT65B-wg Wireless pushbutton with rocker Wireless pushbutton with double rocker Wireless flat pushbutton for single mounting 84x84x11mm or mounting into the E-design switching system. Whisper quiet and with button cell. The scope of supply comprises a mounting base with snapped-on electronics, a flat frame RF1E, a rocker and a double rocker. Wireless pushbuttons with one rocker can transmit two evaluable signals: press rocker up and press rocker down. Wireless pushbuttons with double rocker can transmit four evaluable signals: press two rockers up or down. The mounting base can be screwed onto a flat surface or glued to the wall, on glass or on furniture using the enclosed adhesive foil. Use the sleeves in the 55mm socket box for screw mounting. Snap the large rocker so that the markings 0 and I on the back line up with the same markings on the wireless module. Installation only on a level surface: Screw on or glue mounting plate. First snap on the electronics, then the frame and remove the battery insulator. When you fit the rocker, the 0 mark on the rear must always be on top. We recommend stainless-steel countersunk screws 2.9x25mm, DIN 7982 C, for screw connections. Both with rawl plugs 5x25mm and with 55mm switch boxes. See chapter Z: 'Accessories'. All you need to do to change the CR2032 button cell is remove the rocker. The electronics integrated in the wireless pushbutton can be taught-in encrypted as described in the operating instructions in all encryptable actuators of the Series 61 and Series 71 as well as the FAM14. Encryptable actuators bear the pictogram. 1-7 Rockers and double rockers laser engraved page F4FT65B-wg Wireless fl at pushbutton without wire, pure white glossy EAN ,20 /pc.

14 Bus Flat Pushbutton in E-Design B4FT B4FT65-wg Bus-Taster mit Wippe Bus-Taster mit Doppelwippe Bus pushbutton for single mounting 84x84x11mm or mounting into the E-design switching system. For connection to FTS14TG pushbutton gateway. Only 0.2 watt standby loss. The scope of supply comprises a mounting base with snapped-on electronics, a flat frame RF1E, a rocker and a double rocker. The double rocker permits entry of 4 evaluable signals, but the rocker allows only 2 signals. At the rear, a 20cm long red/black bus line is routed externally. Red terminal to BP, black to BN of a pushbutton gateway FTS14TG. Up to 30 bus switches and/or FTS61BTK pushbutton bus couplers can be connected to terminals BP and BN of an FTS14TG pushbutton gateway. The permitted maximum line length is 150m. The line length is extendable to 250m by fitting an RLC element to the furthest B4. A voltage of 29V DC is supplied to the connected B4 over a 2-wire pushbutton bus which is also used for data transfer. Confirmation telegrams from actuators are displayed by 4 resp. 2 yellow LEDs when the actuator IDs are entered by the PCT14 in the ID table of the FTS14TG. Use the sleeves in the 55mm socket box for screw mounting. Installation: Screw on mounting plate. First snap on the electronics, then the frame and remove the battery insulator. When you fit the rocker, the 0 mark on the rear must always be on top. We recommend stainless-steel countersunk screws 2.9x25mm, DIN 7982 C, for screw connections. Both with rawl plugs 5x25mm and with 55mm switch boxes. See chapter Z: 'Accessories'. Rockers and double rockers laser engraved page RLC element Range extension for B4T65/B4FT65 EAN ,80 /pc. B4FT65-wg Bus flat pushbutton in E-Design, pure white glossy EAN ,80 /pc.

15 E-Design Frames, Fused Safety Socket DSS65 and Blind Cover BLA65 R1E-, R2E- and R3E- Single frame R1E, 84x84 mm external dimensions, double frame R2E, 84x155 mm external dimensions and triple frames R3E, 84x226 mm external dimensions. Internal frame dimensions 63x63mm, 13.5mm high. For all E-design pushbuttons and sensors. 1-9 Side view Pushbutton with frame 16mm high Triple frame R3E Double frame R2E Single frame R1E R1E-wg Single frame pure white glossy EAN ,90 /pc. R2E-wg Double frame pure white glossy EAN ,10 /pc. R3E-wg Triple frame pure white glossy EAN ,30 /pc. DSS65-wg German Fused Safety Socket DSS with socket outlet front in E-design. With increased shock protection. The socket base DSS bearing the VDE sign has plug-in terminals. Fitted in E-design frames R1E, R2E and R3E. DSS65-wg DSS with socket outlet front pure white glossy EAN ,90 /pc. BLA65-wg Blind cover BLA65 for R1E, R2E and R3E. An attachment frame, a mounting plate and an adhesive foil are enclosed. The blind cover snaps flush in the frame after the mounting plate, frame and attachment frame are fitted. BLA65-wg Blind cover for R1E, R2E and R3E pure white glossy EAN ,90 /pc.

16 Flat frames, Fused Safety Socket DSS65F and Blind Cover BLA65F in E-Design 1-10 RF1E-, RF2E- and RF3E- Single flat frame RF1E, 84x84mm external dimensions, double flat frame RF2E, 84x155mm external dimensions and triple frame RF3E, 84x226mm external dimensions. Internal frame dimensions 63x63mm, 8.5mm high. For all E-Design flat pushbuttons and E-Design sensors with AR65/5,2-wg adapter frame. Side view Flat pushbutton with fl at frame 11mm high Triple fl at frame RF3E Double fl at frame RF2E Single fl at frame RF1E RF1E-wg Single fl at frame pure white glossy EAN ,90 /pc. RF2E-wg Double fl at frame pure white glossy EAN ,10 /pc. RF3E-wg Triple fl at frame pure white glossy EAN ,30 /pc. DSS65F-wg German Fused Safety Socket with socket outlet front in E-design for flat frames. With increased shock protection. The socket base DSS bearing the VDE sign has plug-in terminals. Fitted in E-design frames RF1E, RF2E and RF3E. DSS65F-wg DSS with socket outlet front pure white glossy EAN ,90 /pc. BLA65F-wg Blind cover BLA65F for RF1E, RF2E and RF3E. An attachment frame, a mounting plate and an adhesive foil are enclosed. The blind cover snaps flush in the frame after the mounting plate, frame and attachment frame are fitted. BLA65F-wg Blindabdeckung für RF1E, RF2E und RF3E reinweiß glänzend EAN ,90 /pc.

17 Cover for 3-socket TAE TAE65/3-wg Cover for 3-socket telecommunications access unit (TAE). Pure white glossy. For E-Design frames R1E, R2E and R3E. Fits all Rutenbeck TAE access sockets TAE65/3-wg 3-socket TAE cover for E-Design frames EAN ,90 /pc. TAE65F/3-wg Cover for 3-socket telecommunications access unit (TAE). Pure white glossy. For E-Design flat frames RF1E, RF2E and RF3E. Fits all Rutenbeck TAE access sockets. TAE65F/3-wg 3-socket TAE cover for E-Design fl at frames EAN ,90 /pc.

18 Cover for TV/RF 1-12 TV65/2-wg 2-hole cover for TV/RF aerial sockets. Pure white glossy. For E-Design frames R1E, R2E and R3E. Fits all Hirschmann aerial sockets. TV65/2-wg TV/RF cover for E-Design frames EAN ,90 /pc. TV65F/2-wg 2-hole cover for TV/RF aerial sockets. Pure white glossy. For E-Design flat frames RF1E, RF2E and RF3E. Fits all Hirschmann aerial sockets. TV65F/2-wg TV/RF cover for E-Design fl at frames EAN ,90 /pc.

19 Cover for TV/RF/SAT TV65/3-wg 3-hole cover for TV/RF/SAT aerial sockets. Pure white glossy. For E-Design frames R1E, R2E and R3E. Fits all Hirschmann aerial sockets TV65/3-wg TV/RF/SAT cover for E-Design frames EAN ,90 /pc. TV65F/3-wg 3-hole cover for TV/RF/SAT aerial sockets. Pure white glossy. For E-Design flat frames RF1E, RF2E and RF3E. Fits all Hirschmann aerial sockets. TV65F/3-wg TV/RF/SAT cover for E-Design fl at frames EAN ,90 /pc.

20 Cover for UAE/IAE 1-14 UAE65/2-wg Cover for 2-hole UAE/IAE (ISDN) and network sockets. Pure white glossy. For E-Design frames R1E, R2E and R3E. Fits all Rutenbeck or Telegärtner 2-hole UAE/IAE(ISDN) and network sockets. UAE65/2-wg 2-hole UAE/IAE cover for E-Design frames EAN ,90 /pc. UAE65F/2-wg Cover for 2-hole UAE/IAE (ISDN) and network sockets. Pure white glossy. For E-Design flat frames RF1E, RF2E and RF3E. Fits all Rutenbeck or Telegärtner 2-hole UAE/IAE(ISDN) and network sockets. UAE65F/2-wg 2-hole UAE/IAE cover for E-Design fl at frames EAN ,90 /pc.