BNC Connectors (50 ohm/75 ohm)

Transcription

1 BNC Connectors (50 ohm/75 ohm) Product Facts Bayonet lock coupling for quick connect/disconnect Various connectors available in 50 and 75 ohm versions Fully intermateable with comparable BNC UG/U connectors Full range of Hex Crimp and O Crimp Products for common coaxial cables. ow VSWR Single crimp connectors offer one crimping operation for fast application Twist-on connectors require no special tooling for application to the cable Field serviceable (Category A) connectors qualified to MI-C Field replaceable (Category C) plugs with captivated center contact Field replaceable plugs can be terminated with industry standard tooling Tarnish resistant Nickel finish available Choice of different dielectrics isted under the Component Program of Underwriters aboratories Inc., R File No. E81956 PC Board soldered connectors are recognized under the Component Program of Underwriters aboratories Inc., R File No. E81956 Certified by Canadian Standards R Association File No. R 7189 Between Series Adapters For BNC Between Series Adapters, see pages Related Product Data Product Specifications BNC Ohm Terminators BNC O Crimp Connectors BNC Hex Crimp BNC and Hex Crimp Connectors BNC Solder Jacks BNC Connectors (Category A) BNC PCB Panel-Mount Jacks The Tyco Electronics BNC RF connector family with bayonet locking coupling provides highly reliable, quick connect/disconnect coaxial connections. Exclusive single and O crimp terminations allow positive insulation grip and require no soldering, providing terminations at a very low overall applied cost. Available in both 50 and 75 ohm versions, these connectors feature numerous styles including cable plugs and jacks, adapters and printed circuit board connectors. In addition to a variety of crimp type terminations, connectors are furnished in field replaceable and twist-on styles. These connectors accept a wide range of coaxial cables and are intermateable with industry standard connectors designed to MI-C specifications BNC T Adapter BNC 75 Ohm Connectors BNC Feed- Thru and Bulkhead Adapters BNC 50 Ohm Solder Jacks BNC PCB Press Fit Jacks Application Specifications BNC PCB Jack Press Fit Tyco Electronics can also supply low cost alternatives with an extensive commercial type product line. A lower cost consumer series product offers the capability to supply center contacts in strip form and allow for automated center contact crimp technology. All connectors are designed around the mil-specifications, but utilize low-cost materials, offering comparable mechanical and electrical performance. Performance Specifications Page 45 Material Specifications Page 46 Tooling Pages Military Category All MI type O crimp connectors are Category B Type (Tyco Electronics Crimp Tooling), unless otherwise noted. Packaging All MI Type connectors are packaged individually, all O crimp connectors are bulk packaged and all Hex crimp connectors are individually packaged unless otherwise noted. 44

2 BNC Connectors (50 ohm/75 ohm) Performance Specifications Characteristics Single Category B Straight Right-Angle PC Crimp O Crimp Solder Solder O Crimp O Crimp Board Solder (MI Type) (MI Type) Clamp Clamp & Hex Crimp & Hex Crimp 50 Ohms 75 Ohms 50 & 75 Ohms 50 Ohm Jacks Electrical Impedance, Nom. (Ohms) & & 75 Working Voltage (Volts RMS) Resistance Inner: 1.5 Inner: 1.5 Inner: 1.5 Inner: 1.5 Inner: 2.0 Inner: 2.0 Inner: 6/1.5 Inner: 2.75 (Milliohms) Outer: 0.3 Outer: 0.2 Outer:.20 Outer:.20 Outer: 1.0 Outer: 2.0 Outer: 3/0.2 Outer: 1.0 Initial Insulation Resistance (Megohms) Dielectric Withstanding Voltage (VAC) Corona evel at 70,000 ft. (Volts, RMS) RF eakage, (db) -55 at 2-3 GHz -55 at 2-3 GHz -55 at 2-3 GHz -55 at 2-3 GHz -55 at 1-2 GHz RF Insertion oss, (db) 0.2 at 3 GHz 0.2 at 3 GHz 0.3 at 3 GHz 0.2 at 3 GHz 0.15 at 2 GHz Frequency Range (GHz) and VSWR in Frequency Range Mechanical Force to Engage (lbs. [N])/couple, (in-lbs. [N-M]) max. 13.3/11.12 [3/2.5] 13.3/11.12 [3/2.5] 13.3/.028 [3/2.5] 13.3/.028 [3/2.5] 26.7/26.69 [6/6.0] 26.7/26.69 [6/6.0] Coupling Nut Retention, Min. N [lbs.] [100] [100] [100] [100] [60] [60] Cable Retention, N [lbs.] [60] (RG58C/U) [60] (RG58C/U) [40] (RG58C/U) [40] (RG58C/U) [60] (RG58C/U) [60] (RG58C/U) [60] (PCB Ret) Durability (Cycles) Jam Nut Mounting Torque, / [N m] (in. lbs.) [2.8] [2.8] [2.8] [2.8] [2.8] [2.8/1.4] [2.8] Environmental Temperature Range, Operating (C ) -65 to to to to to to to to to +165 Vibration MI-STD-202 MI-STD-202 MI-STD-202 MI-STD-202 MI-STD-1344 MI-STD-202 MI-STD-202 MI-STD-202 Method 204 Method 204 Method 204 Method 204 Method 2005 Method 204 Method 204 Cond. B Cond. B Cond. B Cond. B Cond. III Cond. B Method 201A Cond. B MI-STD-202 MI-STD-202 MI-STD-202 MI-STD-202 MI-STD-1344 MI-STD-202 MI-STD-202 MI-STD-202 Physical Shock Method 213 Method 213 Method 213 Method 213 Method 2004 Method 213 Method 213 Method 213 Cond. G, 50 G s Cond. G, 50 G s Cond. G Cond. G Cond. G, 100 G s Cond. I, 100 G s Cond. I or A, 50 G s Cond. I, 100 G s Thermal Shock MI-STD-202 MI-STD-202 MI-STD-202 MI-STD-202 MI-STD-1344 Method 107 Method 107 Method 107 Method 107 Method 1003 Cond. A MI-STD-202 Method 107 MI-STD-202 Method 107 MI-STD-202 Method 107 Moisture MI-STD-202 MI-STD-202 MI-STD-202 MI-STD-202 MI-STD-1344 Resistance Method 106 Method 106 Method 106 Method 106 Method 1002 Type II MI-STD-202 Method 106 MI-STD-202 Method 106 MI-STD-202 Method 106 MI-STD-202 MI-STD-202 MI-STD-202 MI-STD-202 MI-STD-1344 MI-STD-202 MI-STD-202 MI-STD-202 Salt Spray Method 101 Method 101 Method 101 Method 101 Method 1001 Method 101 Method 101 Method 101 Cond. B Cond. B Cond. B Cond. B Cond. B Cond. B Cond. B Cond. B Product Specification Assembled to cable with polytetrafluorethylene dielectric. 2Assembled to cable with polyethylene dielectric. 3For Metal Threads 4For Polyester Threads 45

3 BNC Connectors (50 ohm/75 ohm) Performance Specifications (Continued) Connector Component Single Category Straight Right-Angle Crimp B & C Solder Solder O Crimp PCB PCB Solder (MI Type) O Crimp Clamp Clamp Hex Crimp & (MI Type) Terminators Solder Press Fit Ohm Jacks Adapters Connector Material Collar QQ-B-626 QQ-B-626 QQ-B-626 Zinc QQ-Z-363 QQ-B-626 Outer (Plug) QQ-B-626 Beryl. Copper Phos. Bronze QQ-B-750 MI-C QQ-B-626 Beryl. Copper QQ-C-530 QQ-C-530 Zinc Shell (Jack) QQ-B-626 QQ-B-626 Zinc QQ-Z-363 Zinc QQ-Z-363 Zinc QQ-Z-363 QQ-Z-363 QQ-B-626 QQ-B-626 TEFON Polyethylene TEFON TEFON Dielectric MI-P Polypropylene TEFON MI-P TEFON TEFON Polypropylene Gen. Purpose1 TEFON MI-P MI-P Polyester PBT MI-P Polypropylene, Gen. Purpose Gen. Purpose MI-P Gen. Purpose (Plug) QQ-B-626 QQ-B-626 QQ-B-626 QQ-B-626 Beryl. Copper QQ-C-530 Beryl. Copper Beryl. Copper Phos. Bronze Phos. Bronze ASTM-B-643 ASTM-B-643 Beryl. Copper Beryl. Copper Beryl. Copper Phos. Bronze Beryl. Copper QQ-B-570 QQ-B-570 (Jack) QQ-C-530 QQ-C-530 QQ-C-530 QQ-B-750 QQ-C-530 Beryl. Copper Beryl. Copper QQ-C-530 QQ-C-530 Gasket Silicon Rubber QQ-R-765 Silicon Rubber QQ-R-765 Silicon Rubber Silicon Rubber Silicon Rubber QQ-R-765 Silicon Rubber QQ-R-765 Ferrule Copper QQ-C-576 Copper QQ-C-576 Copper QQ-C-576 Connector Primary Finishes 2 Silver Silver Silver Collar QQ-S-365 Bright Nickel QQ-S-365 Bright Nickel Silver/ Bright Nickel Silver/ Bright Nickel Bright Nickel QQ-N-290 QQ-S-365 Bright Nickel QQ-N-290 QQ-N-290 QQ-N-290 Silver Bright or Silver Outer s QQ-S-365 QQ-S-365 Silver/ Silver/ Matte Nickel Bright Nickel Bright Nickel Bright Nickel QQ-S-365 (Plug & Jack) Gold Bright Nickel Bright Nickel Bright Nickel QQ-N-290 QQ-N-290 QQ-N-290 QQ-N-290 Bright Nickel QQ-N-290 QQ-N-290 Tin ead Tin ead Tin ead Silver s (Plug & Jack) MI-G Silver Gold MI-G Gold Gold ASTM-B-545 Silver, QQ-S-365 ASTM-B-545 Silver, QQ-S-365 Gold MI-B ASTM-B-545 Silver, QQ-S-365 QQ-S-365 Gold Gold, MI-G Gold, MI-G Gold, MI-G MI-G Silver Ferrule3 QQ-S-365 QQ-S-365 Tin ead Tin ead ASTM-B-545 ASTM-B-545 1Several pc board connectors have an outer polyester PBT insulator per MI-P If more than one finish is listed, refer to individual catalog page(s) or customer drawings for exact specification. 3Ferrules with tin-lead finish are used with nickel plated outer contacts. 46 TEFON is a trademark of E.I. Dupont de Nemours and Company.

4 Plugs, Crimp RF Coax Connectors BNC Connectors, 50 Ohm Single Crimp Hex and O Crimp [.572] [.572] Interchangeable Dies CERTI-CRIMP for PRO-CRIMPER Interchangeable RG/U Termination Dim. Hand Tool Hand Tool Dies for Hand Cable Type Dielectric Style with or Tool Integral Die PRO-CRIMPER & 626 Pneu. Adapter Head , 178A, 178B, Single Crimp Silver TEFON MI Type , 196A Hex Crimp Nickel Polyethylene O Crimp Nickel Polyethylene , , 188A, 316 O Crimp Nickel TEFON MI Type Single Crimp Silver TEFON MI Type Hex Crimp Nickel Polyethylene , 179A, 179B, 161, O Crimp Nickel Polyethylene , 187A, BEDEN 9221 O Crimp Nickel TEFON MI Type Single Crimp Silver TEFON MI Type RD 316, 188, Double Braid O Crimp Nickel Polyethylene Hex Crimp Nickel Polyethylene BEDEN O Crimp Nickel Polyethylene BEDEN 9907, COMM/ O Crimp Nickel Polyethylene SCOPE O Crimp Nickel Polyethylene BEDEN O Crimp Nickel TEFON MI Type Order Tyco Electronics PRO-CRIMPER Coaxial O Crimp Hand Tool assembly , which includes dies Order Tyco Electronics PRO-CRIMPER Coaxial Hex Crimp Hand Tool assembly , which includes dies For use with BEDEN 9907 cable, COMM/SCOPE 3104 cable, and BEDEN 8219 cable only. 4For use with BEDEN cable, and COMM/SCOPE 2104 cable only. BEDEN is a trademark of Belden Wire and Cable Company. COMM/SCOPE is a trademark of Commscope, Inc. TEFON is a trademark of E.I. Dupont de Nemours and Company. 47

5 Plugs, Crimp (Continued) Single Crimp Hex and O Crimp [.572] [.572] Interchangeable Dies CERTI-CRIMP for PRO-CRIMPER Interchangeable RG/U Termination Dim. Hand Tool Hand Tool Dies for Hand Cable Type Dielectric Style with or Tool Integral Die PRO-CRIMPER & 626 Pneu. Adapter Head Hex Crimp Nickel Polyethylene O Crimp Nickel Polyethylene , 58A, B, 58C O Crimp Nickel TEFON MI Type Single Crimp Silver TEFON MI Type BEDEN Hex Crimp Nickel Polyethylene , BERK-TEK BTDC-58, O Crimp Nickel Polyethylene COMM/ SCOPE 2135 O Crimp Nickel TEFON MI Type O Crimp Nickel Polyethylene , 55, 55A, O Crimp Nickel TEFON MI Type B Single Crimp Silver TEFON MI Type O Crimp Nickel Polyethylene , 142A, O Crimp Nickel TEFON MI Type B, Single Crimp Silver TEFON MI Type Consult Tyco Electronics for recommended crimp tooling. 1Order Tyco Electronics PRO-CRIMPER Coaxial O Crimp Hand Tool assembly , which includes dies Order Tyco Electronics PRO-CRIMPER Coaxial Hex Crimp Hand Tool assembly , which includes dies Bulk packaged. BEDEN is a trademark of Belden Wire and Cable Company. BERK-TEK is a trademark of Nexans, Inc. COMM/SCOPE is a trademark of Commscope, Inc. TEFON is a trademark of E.I. Dupont de Nemours and Company. 48

6 Plugs, Crimp (Continued) Single Crimp Hex and O Crimp [.572] [.572] Interchangeable Dies CERTI-CRIMP for PRO-CRIMPER Interchangeable RG/U Termination Dim. Hand Tool Hand Tool Dies for Hand Cable Type Dielectric Style with or Tool Integral Die PRO-CRIMPER & 626 Pneu. Adapter Head Hex Crimp Nickel Polyethylene , 140, 210, O Crimp Nickel Polyethylene , 62A, 62B, 59, 59A, 59B, O Crimp Nickel Polyethylene BEDEN 9291, , 9269 O Crimp Nickel TEFON MI Type Single Crimp Silver TEFON MI Type , BEDEN 88241, 89269, Hex Crimp Nickel Polyethylene Hi-Temp 62A, Times P62, BERK-TEK, BTDC-59, O Crimp Nickel TEFON MI Type BTDC Hi-Temp 59, Times P59, O Crimp Nickel Polyethylene PF59 (20 AWG C.C.) BEDEN 9104, 9240, Hex Crimp Nickel Polyethylene , 9167, , 9266, Times O Crimp Nickel TEFON MI Type FM BEDEN 8281, 9141, 9231, Western Electric Single Crimp Silver Polypropylene MI Type , 728, , 8A, 213 O Crimp Silver TEFON MI Type , 11A O Crimp Silver TEFON MI Type BEDEN 9914, Times FM-8 O Crimp Silver TEFON MI Type Alpha 9847, BEDEN 8213, 9292 O Crimp Silver TEFON MI Type , 9A, 9B, 214 O Crimp Silver TEFON MI Type Order Tyco Electronics PRO-CRIMPER Coaxial O Crimp Hand Tool assembly , which includes dies Order Tyco Electronics PRO-CRIMPER Coaxial Hex Crimp Hand Tool assembly , which includes dies Tyco Electronics PRO-CRIMPER II Hand Tool Frame without dies BEDEN is a trademark of Belden Wire and Cable Company. BERK-TEK is a trademark of Nexans, Inc. TEFON is a trademark of E.I. Dupont de Nemours and Company. 49

7 Plugs, Twist-On Related Product Data Twist-On plugs must be used with cable that has a solid conductor. These plugs are not recommended for applications where the cable frequently moves or flexes [.572] Mating Twist-On Jack Page 52 RG/U Cable 59, 59A, 59B Gold Nickel [1.500] Dielectric Style Interchangeable Dies CERTI-CRIMP for PRO-CRIMPER Interchangeable RG/U Termination Dim. Hand Tool Hand Tool Dies for Hand Cable Type Dielectric Style with or Tool Integral Die PRO-CRIMPER & 626 Pneu. Adapter Head Hex Crimp Gold Nickel Polymethyl , 188, pentene A, 316 Single Crimp Gold Silver TEFON MI Type , 179A, 179B, 161, Hex Crimp Gold Nickel Polymethyl- 187, 187A, pentene BEDEN , 180A, 180B, 195, 195A Hex Crimp Gold Nickel BEDEN 9907, 89907, 8219, COMM/SCOPE Hex Crimp Gold Nickel , 3104 Hex Crimp Gold Nickel , 58A, 58B, 58C O Crimp Gold Nickel TEFON MI Type Single Crimp Gold Silver TEFON MI Type O Crimp Gold Nickel TEFON MI Type , 55A, B, 223 Single Crimp Gold Silver TEFON MI Type , 142A, 142B, 400 Single Crimp Gold Silver TEFON MI Type , 140, 210, 62, 62A, 62B, 59, 59A, 59B, O Crimp Gold Nickel TEFON MI Type BEDEN 9291, , Right-Angle Plugs, Crimp Single Crimp Hex and O Crimp [1.046] [1.046] [.572] [.572] 50 BEDEN is a trademark of Belden Wire and Cable Company. COMM/SCOPE is a trademark of Commscope, Inc. TEFON is a trademark of E.I. Dupont de Nemours and Company.

8 Jacks, Crimp Single Crimp Hex and O Crimp 11.1 [.437] [.436] Interchangeable Dies CERTI-CRIMP for PRO-CRIMPER Interchangeable RG/U Termination Dim. Hand Tool Hand Tool Dies for Hand Cable Type Dielectric Style with or Tool Integral Die PRO-CRIMPER & 626 Pneu. Adapter Head Hex Crimp Gold Nickel O Crimp Gold Nickel Polypro , 188, pylene A, 316 O Crimp Gold Nickel TEFON MI Type Single Crimp Gold Silver TEFON MI Type , 179A, 179B, 161, 187, 187A, Hex Crimp Gold Nickel BEDEN 9221 O Crimp Gold Nickel Polypro , 58A, pylene B, 58C O Crimp Gold Nickel TEFON MI Type , 55, 55A, 55B Single Crimp Gold Silver TEFON MI Type , 140, 210, O Crimp Gold Nickel Polypro , 62A, 62B, pylene , 59A, 59B, BEDEN 9291, O Crimp Gold Nickel TEFON MI Type , Order Tyco Electronics PRO-CRIMPER Coaxial O Crimp Hand Tool assembly , which includes dies BEDEN is a trademark of Belden Wire and Cable Company. TEFON is a trademark of E.I. Dupont de Nemours and Company. 51

9 Jacks, Twist-On Related Product Data Twist-on jacks must be used with cable that has a solid conductor. These jacks are not recommended for applications where the cable frequently moves or flexes. Mating Twist-On Plug Page [1.580] RG/U Cable Dielectric Style 59, 59A, 59B Gold Nickel Acetal Panel Jacks, Crimp 12.7 ±0.1 [.500 ±.004] 11.2 [.441] [.702] [1.140] 12.7 ±0.1 [.500 ±.004] 2.77 [.109] Recommended Panel Cutout Interchangeable Dies CERTI-CRIMP for PRO-CRIMPER Interchangeable RG/U Termination Hand Tool Hand Tool Dies for Hand Cable Type Dielectric Style with or Tool Integral Die PRO-CRIMPER & 626 Pneu. Adapter Head , 188, 188A, 316 O Crimp Gold Nickel TEFON MI Type , 58A, 58B, 58C O Crimp Gold Nickel TEFON MI Type , 140, 210, 62, 62A, 62B, 59, 59A, 59B, BEDEN 9291, O Crimp Gold Nickel TEFON MI Type , 9269, BEDEN is a trademark of Belden Wire and Cable Company. TEFON is a trademark of E.I. Dupont de Nemours and Company.

10 Bulkhead Jacks, Crimp Single Crimp Hex and O Crimp Note: Panel Insulating Bushings Page 54 H H Recommended Panel Cutouts Maximum Panel Thickness 3.18 [.125] [.505] Min [.435] Min [ ] H = 11/16" across flats, [.800] across points [ ] Interchangeable Dies CERTI-CRIMP for PRO-CRIMPER Interchangeable RG/U Termination Dim. Hand Tool Hand Tool Dies for Hand Cable Type Dielectric Style with or Tool Integral Die PRO-CRIMPER & 626 Pneu. Adapter Head Hex Crimp Gold Nickel O Crimp Gold Nickel Polypro , 188, pylene A, 316 O Crimp Gold Nickel TEFON MI Type Single Crimp Gold Silver TEFON MI Type , 179A, O Crimp Gold Nickel TEFON MI Type B, 161, , 187A, Single Crimp Gold Silver TEFON MI Type BEDEN Times RD316 O Crimp Gold Nickel TEFON MI Type BEDEN is a trademark of Belden Wire and Cable Company. TEFON is a trademark of E.I. Dupont de Nemours and Company. 53

11 Bulkhead Jacks, Crimp (Continued) Single Crimp Hex and O Crimp Note: Panel Insulating Bushings at the bottom of this page H H Recommended Panel Cutouts Maximum Panel Thickness 3.18 [.125] [.505] Min [.435] Min [ ] H = 11/16" across flats, [.800] across points [ ] Interchangeable Dies CERTI-CRIMP for PRO-CRIMPER Interchangeable RG/U Termination Dim. Hand Tool Hand Tool Dies for Hand Cable Type Dielectric Style with or Tool Integral Die PRO-CRIMPER & 626 Pneu. Adapter Head , 58A, 58B, 58C, BEDEN 88240, BERK-TEK Hex Crimp Gold Nickel BTDC-58, COMM/SCOPE 2135 O Crimp Gold Nickel Polypropylene , 58A, 58B, 58C O Crimp Gold Nickel TEFON MI Type Single Crimp Gold Silver TEFON MI Type , 55, 55A, 55B O Crimp Gold Nickel TEFON MI Type , 142A, 142B, 400 O Crimp Gold Nickel TEFON MI Type , 140, 210, 62, 62A, 62B, 59, 59A, 59B, O Crimp Gold Nickel Polypro BEDEN 9291, pylene , Order Tyco Electronics PRO-CRIMPER Coaxial O Crimp Hand Tool assembly , which includes dies Panel Insulating Bushings for Bulkhead Jacks Material Nylon 0.89 [.035] 0.81 [.032] [.509] 5.46 [.215] [.549] 14.73±0.13 [.580±.005] Note: Can not be used with single crimp bulkhead jacks. 14.1±0.08 [.555±.003] 54 BEDEN is a trademark of Belden Wire and Cable Company. BERK-TEK is a trademark of Nexans, Inc. COMM/SCOPE is a trademark of Commscope, Inc. TEFON is a trademark of E.I. Dupont de Nemours and Company [.687] [.574] (2 Required) Recommended Panel Cutout

12 Plugs, for JIS Cables, Crimp Nickel Gold [.572] Interchangeable Dies for PRO-CRIMPER JIS Cable Termination Type Dielectric Dim. Hand Tool or PRO-CRIMPER Adapter D-2V Hex Crimp Polyethylene Bulkhead Solder Jacks, Front Mount Without Solder Terminal With Solder Terminal Nickel [.875] 9.65/9.75 [.380/.384] 3/8" - 32 Thread Accepts 1.5 [.059] Wire Accepts 1.5 [.059] Wire 3/8" - 32 Thread.396/4.04 [.156/.159] Recommended Panel Cutout W W TEFON is a trademark of E.I. Dupont de Nemours and Company. VAOX is a trademark of General Electric Company. Dimensions Dielectric Panel Insulating Material W Thickness Bushing Without Solder With Solder Terminal* Terminal** Silver VAOX or or VAOX or Gold or TEFON or or Tin VAOX or **Includes lockwasher and jam nut. **Includes solder terminal and jam nut. 55

13 Insulating Bushings 0.94 [.030] 1.09 [.043] [.450] 4.04 [.159] [.430] 0.81 [.032] 1.78 [.070] 12.7 [.500] 3.94 [.155] [.470] [.585] 9.53 [.375] ±0.08 [.455 ±.003] [.625] 9.53 [.375] ±0.08 [.505 ±.003] ±0.06 [.432 ±.003] 12.07±0.08 [.475 ±.003] Recommended Panel Cutout Recommended Panel Cutout Isolated Bulkhead Solder Jacks, Front Mount Nickel Dielectric White VAOX 3/8" - 24 Thread Accepts 1.5 [.059] DIa. Wire [ ] Flange & Thread Material Part No. Tin VAOX Silver VAOX Gold VAOX [.515] [1.250] 3/8" - 24 Thread Panel Thickness [ ] Recommended Panel Cutout [ ] Nickel Silver Dielectric Black VAOX Flange & Thread Material Black VAOX [.505] [1.055] [ ] [ ] Panel Thickness [ ] Recommended Panel Cutout Sealed Bulkhead Solder Jack, Rear Mount Nickel Gold Dielectric This connector is designed to prevent moisture from entering the interface from the rear of the connector. 1/2" - 28 Thread Rubber Gasket [1.250] [.700] Accepts. 1.5 [.059] DIa. Wire [ ] [ ] Maximum Panel Thickness 6.35 [.250] 56 VAOX is a trademark of General Electric Company Recommended Panel Cutout

14 Right-Angle Jacks PC Board/Panel Mount Nickel Dielectric VAOX 1/2-28 Thread C Mtg. Hgt. Metal 1/2-28 Thread C Mtg. Hgt. C A B [1.375] C A B [1.375] Mounting Post Style Compliant Post [ ] E [ ] Dimensions Material Without With With A B C Mounting Posts Mounting Posts Compliant Posts Tin VAOX, White Gold Gold Tin Gold VAOX, Black Gold Gold Tin Metal Gold Gold Gold High Temp. Housing Gold : Gold [ ] thick Gold [ ] thick Note: If an Insulating Bushing is required see part number and Panel Cutout on page 54. Maximum Panel Thickness 6.1 [.240] Recommended Panel Cutout ockwasher and Jam Nut Without Mounting Posts With Mounting Posts ±0.05 [.200 ±.002] 2.54 ±0.05 [.100 ±.002] ±0.08 [.400 ±.003] G S 0.89 ±0.08 [.035 ±.003] (Top View) 5.08 ±0.05 [.200 ±.002] 2.64 [.104] Clearance Hole for 2-56 Self-Tapping Screw* (2 Holes) Mating Face 5.08 ±0.05 [.200 ±.002] 2.54 ±0.05 [.100 ±.002] ±0.08 [.400 ±.003] (Top View) 2.01 ±0.05 [.079 ±.002] (2 Holes) 5.08 ±0.05 [.200 ±.002] Mating Face G S 0.89 ±0.08 [.035 ±.003] Recommended PC Board ayouts VAOX is a trademark of General Electric Company. 57

15 Vertical Jacks PC Board/Panel Mount VAOX Metal Nickel Dielectric 1/2-28 Thread [.625] 1/2-28 Thread [.625] [ ] B [1.375] Mtg. Hgt. B [1.375] Mtg. Hgt [ ] Maximum Panel Thickness 6.1 [.240] Recommended Panel Cutout ockwasher and Jam Nut Dim. Dim. Without With Material B Mounting Mounting Posts Posts Tin VAOX, White Gold Tin VAOX, Black Gold Metal Tin Gold Note: If an Insulating Bushing is required see part number and Panel Cutout on page Without Mounting Posts 5.08 ±0.05 [.200 ±.002] 2.64 [.104] Clearance Hole for 2-56 Self-Tapping Screw* (2 Holes) With Mounting Posts 5.08 ±0.05 [.200 ±.002] 2.01 ±0.08 [.079 ±.003] (2 Holes) ±0.08 [.400 ±.003] G S ±0.08 [.400 ±.003] 5.08 ±0.05 [.200 ±.002] 2.54 ±0.05 [.100 ±.002] 0.89 ±0.08 [.035 ±.003] ±0.08 [.400 ±.003] G S ±0.08 [.400 ±.003] 5.08 ±0.05 [.200 ±.002] 2.54 ±0.05 [.100 ±.002] 0.89 ±0.08 [.035 ±.003] (Top View) (Top View) Recommended PC Board ayouts * Screw for board thickness of 2.38 [.093] or greater Screw for thickness of less than 2.38 [.093] VAOX is a trademark of General Electric Company.

16 Jacks with Mounting Flanges PC Board/Panel Mount 1/2-28 Thread [.625] Mounting Height [ ] [ ] Maximum Panel Thickness 6.1 [.240] C 8.59 [.338] [.835] [1.375] Recommended Panel Cutout Material VAOX, Tin White Gold ockwasher and Jam Nut [.130] Clearance Hole for 5-40 Screw ±0.08 [.900 ±.003] 8.89 [.350] 0.89 ±0.08 [.035 ±.003] G S (Top View) 2.54 [.100] [.450] Mating Face Recommended PC Board ayout VAOX is a trademark of General Electric Company. 59

17 Vertical Metalized Jacks PC Board Mount Recommended PC Board ayouts Style A Sq. [.687] [.625] Drill Holes for 0.94 ±0.05 [.037 ±.002] Pin (5 Places) 12.7 ±0.08 [.500 ±.003] 6.35 ±0.05 [.250 ±.002] 6.35 ±0.05 [.250 ±.002] 12.7 ±0.08 [.500 ±.003] Dielectric Style eg ength Silver VAOX A Gold VAOX A Nickel Tin VAOX A Gold VAOX A Silver VAOX C Gold VAOX E Gold TEFON B Tin-ead Silver VAOX C Gold VAOX D Style B 6.88 ±0.08 [.271 ±.003] 1With.76 [.030] standoffs on top of legs ± ±0.08 [.059 ±.003] [.135 ±.003] (4 Holes) [.810] 1.02 ±0.08 [.040 ±.003] 3.43 ±0.08 [.135 ±.003] 6.88 ±0.08 [.271 ±.003] Style C 6.88 ±0.05 [.271 ±.003] 3.43 ±0.05 [.135 ±.002] 2.44 ±0.08 [.096 ±.003] (4 Holes) Style D 4.32 [.170] 1.07 ±0.05 [.042 ±.002] 6.88 ±0.05 [.271 ±.003] 1.32 ±0.08 [.052 ±.003] 6.48 [.255] 1.73 ±0.05 [.068 ±.002] [.655] [.625] 3.73 [.147] 7.47 [.294] Style E (Panel Mount) [ ] Drill Hole to Receive [.037±.002] Pin, 5 Required [.500 ±.003] 6.35 ±0.06 [.250 ±.002] 60 TEFON is a trademark of E.I. Dupont de Nemours and Company. VAOX is a trademark of General Electric Company [.500 ±.003]

18 Vertical Metalized Jacks, PC Board Mount [.945] 7.50 ± 0.08 [.295 ±.003] 1.00 ± 0.08 [.039 ±.003] 2 Plcs. Signal Hole Switching Hole 1.70 ± 0.10 [.067 ±.004] ± 0.25 [.422 ±.010] 2.50 ± 0.08 [.098 ±.003] 4 Plcs ± 0.08 [.421 ±.003] 3.00 ± 0.10 [.118 ±.004] 1.50 ± 0.08 [.059 ±.003] 2 Plcs (Switching) Recommended PC Board ayout [.945] 3.75 ± 0.08 [.148 ±.003] 1.00 ± 0.08 [.039 ±.003] 2.50 ± 0.08 [.098 ±.003] 3 Plcs ± 0.10 [.067 ±.004] ± 0.25 [.422 ±.010] ± 0.08 [.421 ±.003] 3.00 ± 0.10 [.118 ±.004] 1.50 ± 0.08 [.059 ±.003] 2 Plcs Recommended PC Board ayout Dielectric Part No. Tin Silver Polyphenylene Tin Silver Polyphenylene Press Fit Vertical Metalized Jack, PC Board Mount [.470] 6.88 ±0.05 [.271 ±.002] 3.43 ±0.05 [.135 ±.002] 6.88 ±0.05 [.271 ±.002] [.059 ] Holes 1.02 ±0.08 [.040 ±.003] Insulating Bushing Material Polypropylene Only to be used on Part Nos & [.575] [.470] [.810] Recommended PC Board ayout PC Board Thickness Not ess Than 0.99 [.093] 2.96 [.115] 6.61 [.260] 61

19 Right-Angle Metalized Jacks, PC Board Mount C 6.15 [.242] ± 0.51 [1.088 ±.020] [.432] Mounting Height 6.6 ± 0.08 [.260 ±.003] 3.3 ± 0.08 [.130 ±.003] 6.6 ± 0.08 [.260 ±.003] 2.11 ± 0.08 [.083 ±.003] (4 holes) 1.17 ± 0.08 [.046 ±.003] Dielectric ength Part No. Nickel * Tin TEFON * Nickel * Maximum PC Board Thickness 2.54 [.100] Recommended PC Board ayout 3.81 ±0.08 [.150 ±.003] 1.19 ±0.18 [.047 ±.007] 8.64 [.340] 7.62 ±0.08 [.300 ±.003] Dielectric Part No. Nickel TPX Gold [.860] [1.000] 7.62 ±0.08 [.300 ±.003] 1.78 ±0.08 [.070 ±.003] 2 Holes Recommended PC Board ayouts Right-Angle Metalized Jacks, PC Board/Panel Mount 6.15 ± 0.25 [.242 ±.010] [.459] ± 0.51 [1.088 ±.020] ± 0.18 [.432 ±.007] 6.6 ± 0.08 [.260 ±.003] 3.3 ± 0.08 [.130 ±.003] [ ] 6.6 ± 0.08 [.260 ±.003] 2.11 ± 0.08 [.083 ±.003] 4 holes 1.17 ± 0.08 [.046 ±.003] Dielectric Part No. Tin TEFON Tin TPX /2-28 Thread ockwasher and Jam Nut see page 59. TEFON is a trademark of E.I. Dupont de Nemours and Company. TPX is a trademark of Mitsui Chemicals America, Inc [.171] [ ] Maximum Panel Thickness 6.35 [.250] Recommended Panel Cutout

20 Tee Adapters Style A (Jack-Plug-Jack) Style B With Insulated Cover (Jack-Plug-Jack) Style C (Jack-Jack-Jack) D Insulation Material Polyphenylene oxide D D F E E E F Dimensions Comparable Packaging Style Material Material Dielectric UG/U No. and and D E F Connector Per Pkg., Nickel BE CU, Gold (30)2 TEFON A Bulk (100) PH BR, Gold (15)2 Acetal Bulk (100) A BE CU, Gold Acetal Bulk Zinc, (30) (100) Nickel PH BR, Gold Acetal Individual (15) (1) BE CU, Silver (200)2 Acetal Individual (1) B Zinc, Nickel BE CU, Gold (30)2 Acetal Bulk (100) C, Nickel BE CU, Silver (200)2 TEFON Bulk (100) Zinc, Nickel PH BR, Gold (50)2 Acetal Bulk (100) Gray insulation cover 2 (Microinches min thickness) 3 (Special graphics) Tee Adapter Covers Material Polypropylene, general purpose ± 0.76 [4.510 ±.030] Color Black Ivory Part No [.595] 5.08 [.200] TEFON is a trademark of E.I. Dupont de Nemours and Company. 63

21 Jack-Jack Adapters Style A [1.281] Style B [1.410] Dielectric Style Nickel Silver TEFON A Nickel Gold TEFON A Nickel Gold B Bulkhead Jack-Jack Adapters [ ] [ ] H Recommended Panel Cutout H= 11/16 across flats, [.800] across points. Isolated Bulkhead Jack-Jack Adapter Dimensions H Dielectric Nickel Silver TEFON Nickel Gold Polyethylene Nickel Gold Polyethylene : Gold [ ] thick Gold [ ] thick Note: If an Insulating Bushing is required see part number and Panel Cutout on page [ ] Dielectric Nickel Gold [.625] [1.420] [ ] Recommended Panel Cutout H= 11/16 across flats, [.800] across points. Plug-Plug Adapter 31.8 [1.252] Ref. Gold Nickel Right-Angle Adapters (Jack-Plug) Dia [.572] Dielectric Nickel Silver TEFON Nickel Gold TEFON Nickel Gold [.901] [1.062] 64 TEFON is a trademark of E.I. Dupont de Nemours and Company.

22 Terminator Plugs 50, 75, 93 Ohm Nickel Gold Dielectric Polyethylene [.572] [1.300] Tether Resistor Specification With Tether Without Tether 1 Watt, 50 Ohm Watt, 75 Ohm Watt, 93 Ohm Watt, 75 Ohm 1 Watt, 50 Ohm Tether is conductive with #4 stud size #6 Stud Size Insulated Terminators ong Cover Insulation Material Polyphenylene oxide [1.500] [1.500] [.685] [.685] Short Cover* Register Color Cover Part Specification Style No. ong Gray 1 Watt, 50 Ohm Short Black ong * The Short Cover is required when mating the Terminator with a Tee Adapter. Jack Covers Silver Nickel [.870] [.572] Shorting Caps Nickel Gold [.600] [4.000] #6 Stud Size [.572]

23 BNC Connectors, 75 Ohm Plugs, Crimp Hex and O Crimp These connectors have been designed for optimum performance and have a true 75 ohm impedance the complete length of the connector. The crimp die tooling listed below is different from the equivalent 50 ohm connectors [.572] Plugs Interchangeable Dies for Interchangeable RG/U Termination Dim. PRO-CRIMPER Dies for Hand Cable Type Dielectric Style Hand Tool Tool or & 626 Pneu. PRO-CRIMPER Head Adapter , 179A, Hex Crimp Gold Nickel Polyethelene B, 187, A, 161, O Crimp Gold Nickel Polyethelene BEDEN AT&T 735A Hex Crimp Gold Nickel Polyethelene O Crimp Gold Nickel Polyethelene BEDEN 8218 Hex Crimp Gold Nickel Polyethelene O Crimp Gold Nickel Polyethelene , 210, 62, 62A, Hex Crimp Gold Nickel Polyethelene B, 59, 59A, 59B, BEDEN 9291, O Crimp Gold Nickel Polyethelene , , BEDEN 89269, 88241, Hi-Temp 62A, Times P-62, Berk Tek Hex Crimp Gold Nickel Polyethelene BTDC-59, BTDC-62 BEDEN 8212, 9104, , 9167, 9240, 9259, Hex Crimp Gold Nickel Polyethelene , Times FM-59, (RG 59 Type O Crimp Gold Nickel Polyethelene with 20 AWG C.C.) Hex Crimp Gold Nickel Polyethelene BEDEN 9145, AT&T 734A O Crimp Gold Nickel Polyethelene BEDEN 9248, 9114 O Crimp Gold Nickel Polyethelene , 6A O Crimp Gold Nickel Polyethelene BEDEN 8281, , 9231, Hex Crimp Gold Nickel Polyethelene Western Electric 724, O Crimp Gold Nickel Polyethelene , COMM/SCOPE O Crimp Gold Nickel Polyethelene S59 Hec COMM/SCOPE F59 Hec-z O Crimp Gold Nickel Polyethelene AT&T is a trademark of AT&T Corporation. BEDEN is a trademark of Belden Wire and Cable Company. COMM/SCOPE is a trademark of Commscope, Inc.

24 BNC Connectors, 75 Ohm (Continued) Plugs for JIS Cables, Crimp Nickel Gold [.572] Interchangeable Dies for PRO-CRIMPER JIS Cable Termination Type Dielectric Dim. Hand Tool or PRO-CRIMPER Adapter C-2V Hex Crimp C-2V Hex Crimp Bulkhead Jacks for JIS Cables, Crimp Nickel Gold Dielectric [.800] Interchangeable Dies for PRO-CRIMPER JIS Cable Termination Type Dielectric Dim. Hand Tool or PRO-CRIMPER Adapter C-2V Hex Crimp 75Ω * *Packaged in 100 pieces per bag. 67

25 BNC Connectors, 75 Ohm (Continued) Right-Angle Plugs, Crimp Hex and O Crimp [1.070] [.572] Interchangeable Dies for Interchangeable RG/U Termination Dim. PRO-CRIMPER Dies for Hand Cable Type Dielectric Style Hand Tool Tool or & 626 Pneu. PRO-CRIMPER Head Adapter , 179A, 179B, 187, 187A, 161 Hex Crimp Gold Nickel BEDEN 9221 AT&T 735A Hex Crimp Gold Nickel AT&T KS , RD179 Hex Crimp Gold Nickel Double Braid 140, 210, 62, Hex Crimp Gold Nickel Polymethyl- 62A, 62B, 59, pentene A, 59B, BEDEN 9291, O Crimp Gold Nickel Polymethyl , 9269 pentene BEDEN 8212, 9104, 9112, 9240, 9167, 9259, 9266, Times FM-59, Hex Crimp Gold Nickel (RG 59 Type with 20 AWG C.C.) BEDEN 9145, AT&T 734A O Crimp Gold Nickel AT&T is a trademark of AT&T Corporation. BEDEN is a trademark of Belden Wire and Cable Company. 68

26 BNC Connectors, 75 Ohm (Continued) Jacks, Crimp Hex and O Crimp [.436] Interchangeable Dies for Interchangeable RG/U Termination Dim. PRO-CRIMPER Dies for Hand Cable Type Dielectric Style Hand Tool Tool or & 626 Pneu. PRO-CRIMPER Head Adapter , 179A, Hex Crimp Gold Nickel Polyethelene B, 161, , 187A, O Crimp Gold Nickel Polyethelene BEDEN BEDEN 8218 Hex Crimp Gold Nickel Polyethelene 140, 210, 62, 62A, 62B, 59, 59A, 59B, O Crimp Gold Nickel Polyethelene BEDEN 9291, 9209, , BEDEN 88241, 89269, Hi-Temp 62A, Times P-62, Berk Hex Crimp Gold Nickel Polyethelene Tek BTDC-59, BTDC-62 BEDEN 8212, 9104, 9112, 9240, 9167, 9259, 9266, Times FM-59, Hex Crimp Gold Nickel Polyethelene (RG 59 Type with 20 AWG C.C.) BEDEN 9248, 9114 O Crimp Gold Nickel Polyethelene BEDEN is a trademark of Belden Wire and Cable Company. 69

27 Bulkhead Jacks, Crimp BNC Connectors, 75 Ohm (Continued) Hex and O Crimp [ ] [.800] [1.375] [ ] Maximum Panel Thickness 6.1 [.240] Recommended Panel Cutout Interchangeable Dies for Interchangeable RG/U Termination Dim. PRO-CRIMPER Dies for Hand Cable Type Dielectric Style Hand Tool Tool or & 626 Pneu. PRO-CRIMPER Head Adapter , 179A, Hex Crimp Gold Nickel Polyethelene B, 161, , 187A, O Crimp Gold Nickel Polyethelene BEDEN AT&T KS , RD179 Hex Crimp Gold Nickel Polyethelene Double Braid BEDEN 8218 Hex Crimp Gold Nickel Polyethelene , 210, 62, 62A, 62B, 59, 59A, 59B, O Crimp Gold Nickel Polyethelene BEDEN 9291, , 9269 BEDEN 8212, 9104, 9112, 9240, 9167, 9259, 9266, Times FM-59 O Crimp Gold Nickel Polyethelene (RG 59 Type with 20 AWG C.C.) BEDEN 9114, 9248 O Crimp Gold Nickel Polyethelene AT&T is a trademark of AT&T Corporation. BEDEN is a trademark of Belden Wire and Cable Company. 70

28 BNC Connectors, 75 Ohm (Continued) Bulkhead Solder Jacks Front Mount Nickel Silver [1.083] Accepts.054 Wire [1.083] Accepts.054 Wire 9.75/9.65 [.384./380] [.515] 3/8-32 Thread [.515] 3/8-32 Thread /3.96 [.159/.156] (without Solder Terminal) (with Solder Terminal) Maximum Panel Thickness 3.18 [.125] Recommended Panel Cutout Note: If insulating bushing required use part no or (for details, reference page 55). Note: If insulating bushing required use part no or (for details, reference page 55). Bulkhead Jack PC Board Mount 3.30 [.130] [.436] Ø ± 0.1 [.500 ±.004] 20.8 [.820] 11.2 ± 0.1 [.441 ±.004] Bulkhead Solder Jack Rear Mount ockwasher and Jam Nut see page 73. 1/2-28 Thread Accepts..050 WIre [.700] [ ] Nickel Gold Dielectric [1.250] [ ] Maximum Panel Thickness 6.35 [.250] Recommended Panel Cutout 71

29 Right-Angle Jacks PC Board/Panel Mount Outer Shell Nickel Dielectric ockwasher and Jam Nut see page 73. BNC Connectors, 75 Ohm (Continued) VAOX Metal 1/2-28 Threads 1/2-28 Threads C Mtg. Hgt. C Mtg. Hgt. C A B [1.375] C A B [1.375] Recommended PC Board ayouts Without Mounting Posts 5.08 ±0.05 [.200 ±.002] 2.54 ±0.05 [.100 ±.002] ±0.08 [.400 ±.003] G S 0.89 ±0.08 [.035 ±.003] (Top View) With Mounting Posts 5.08 ±0.05 [.200 ±.002] [ ] 2.54 ±0.05 [.100 ±.002] ±0.08 [.400 ±.003] (Top View) [ ] Maximum Panel Thickness 6.1 [.240] Recommended Panel Cutout 5.08 ±0.05 [.200 ±.002] * Screw for panel thickness of 2.38 [3/32] or greater * * Screw for panel thickness of less than 2.38 [3/32] * [.104] Clearance Hole for 2-56 Self-Tapping Screw* (2 Holes) Mating Face 2.01 ±0.08 [.079 ±.003] (2 Holes) 5.08 ±0.05 [.200 ±.002] Mating Face G S 0.89 ±0.08 [.035 ±.003] Dimensions Material Without With A B C Mounting Posts Mounting Posts VAOX, Black w/ * Compliant Posts Gold (Economy)* VAOX, * Black Gold (Economy)* VAOX, White Gold VAOX, * White Gold (Economy)* VAOX, Black Gold Gold VAOX, Black (Economy)* Gold VAOX, White Gold Metal Gold Metal Gold Metal (Economy)* Gold Metal with Gold Compliant Posts Tin (Economy)* Metal Gold Metal Gold Metal Gold Metal (Economy)* Gold **Economy connector uses 50 Ω part with smaller dielectric and stamped and formed contact, Phosphor Bronze contact material (Compare to regular connector which is 75 Ω, screw machined Beryllium Copper). : Gold [ ] thick Gold [ ] thick Note: If an Insulating Bushing is required see part number and Panel Cutout on page VAOX is a trademark of General Electric Company.

30 BNC Connectors, 75 Ohm (Continued) Vertical Jacks PC Board/Panel Mount VAOX Metal Outer Shell Nickel Dielectric 1/2-28 Thread [.625] 1/2-28 Thread [.625] B [1.375] Mtg. Hgt. B [1.375] Mtg. Hgt [ ] [ ] Maximum Panel Thickness 6.1 [.240] Recommended Panel Cutout ockwasher and Jam Nut Material Dim. B Dim. VAOX, Black Gold (Economy)* VAOX, White Gold (Economy)* Metal Gold Metal (Economy)* Tin *Economy connector uses 50 Ω part with smaller dielectric and stamped and formed contact, Phosphor Bronze contact material (Compare to regular connector which is 75 Ω, screw machined Beryllium Copper). : Gold [ ] thick Note: If an Insulating Bushing is required see part number and Panel Cutout on page ±0.05 [.200 ±.002] 2.01 ±0.08 [.079 ±.003] (2 Holes) * Screw for panel thickness of 2.38 [3/32] or greater * * Screw for panel thickness of less than 2.38 [3/32] * ±0.08 [.400 ±.003] G S ±0.08 [.400 ±.003] 5.08 ±0.05 [.200 ±.002] 2.54 ±0.05 [.100 ±.002] 0.89 ±0.08 [.035 ±.003] (Top View) Recommended PC Board ayout VAOX is a trademark of General Electric Company. 73

31 Vertical Metalized Jacks PC Board Mount BNC Connectors, 75 Ohm (Continued) Style A Style B Style C Dielectric TEFON Sq. [.687] [.625] [.810] [.655] 12.7 ±0.08 [.500 ±.003] 6.35 ±0.05 [.250 ±.002] 1.50 ±0.08 [.059 ±.003] (4 Holes) 6.88 ±0.08 [.271 ±.003] 3.44 ±0.08 [.135 ±.003] 6.88 ±0.05 [.271 ±.003] 3.43 ±0.05 [.135 ±.002] 2.44 ±0.08 [.096 ±.003] (4 Holes) 12.7 ±0.08 [.500 ±.003] 6.88 ±0.08 [.271 ±.003] 6.88 ±0.05 [.271 ±.003] 1.32 ±0.08 [.052 ±.003] Drill Holes for 0.94 ±0.05 [.037 ±.002 ] Pin (5 Places) 6.35 ±0.05 [.250 ±.002] 1.02 ±0.08 [.040 ±.003] 3.43 ±0.08 [.135 ±.003] Recommended PC Board ayout Style F (Push-On) Plcs. [.100] [.580] ± [.1015 ±.0030] 5.16 ± 0.08 [.203 ±.003] 2.06 ± 0.05 [.081 ±.002] 4 Plcs ± 0.08 [.203 ±.003] 1.02 ± 0.08 [.040 ±.003] eg Style ength Nickel Gold B Tin Gold B Tin Gold B Tin Gold C Nickel Silver A Tin Gold F Press Fit Vertical Metalized Jacks PC Board Mount [.470] A 6.88 ±0.1 [ ] ± ±0.05 [.271 ±.002] 3.43 ±0.05 [.135 ±.002] [ ].003 (4 Plated-Thru Holes) 1.02 ±0.08 [.040 ±.003] (Plated-Thru Hole) Dim. A Part No Recommended PC Board ayout Insulating Bushing 74 Material Nylon Only to be used on Part Nos and TEFON is a trademark of E.I. Dupont de Nemours and Company [.575] [.470] 2.96 [.115] 6.61 [.260]

32 BNC Connectors, 75 Ohm (Continued) Press Fit Vertical Metalized Jacks PC Board Mount (Continued) [.688] Sq. 1.7 ±0.05 [.067 ±.002] (2 Places) For Drive Screw 1.02 ±0.08 [.040 ±.003] (Plated-Thru Hole 3 Places) 12.7 ±0.05 [.500 ±.002] 6.35 ±0.05 [.250 ±.002] 12.7 ±0.05 [.500 ±.002] PC Board Thickness (Min.) [.625] 6.35 ±0.05 [.250 ±.002] Recommended PC Board ayout Press Fit, Bulkhead Vertical Metalized Jack includes hardware [.425] 4.37 ± 0.51 [.172 ±.020] 5 Plcs [.135] 6.88 [.271] 3.43 [.135] ø [ø ] [1.133] [.961] 6.88 [.271] Ø 1.02 ± 0.08 [.040 ±.003] [ ] Holes Plated Through 5 Plcs. Right-Angle Metalized Jacks PC Board Mount C 6.15 [.242] 28.4 [1.118] [.432] Mounting Height 6.6 ± 0.08 [.260 ±.003] 3.3 ± 0.08 [.130 ±.003] 6.6 ± 0.08 [.260 ±.003] 2.11 ± 0.08 [.083 ±.003] (4 holes) 1.17 ± 0.08 [.046 ±.003] Recommended PC Board ayout Dielectric Dimension Nickel TPX Gold2.171 [.007] Tin TEFON Gold2.171 [.007] Nickel TPX Gold2.131 [.005] Nickel TPX Gold1.171 [.007] Gold [ ] thick Gold [ ] thick Maximum PC Board Thickness 2.54 [.100] Recommended PC Board ayout ± 0.43 [.450 ±.017] 3.81 ± 0.08 [.150 ±.003] 1.19 ± 0.18 [.047 ±.007] TEFON is a trademark of E.I. Dupont de Nemours and Company. TPX is a trademark of Mitsui Chemicals America, Inc [.436] [.700] [.860] ± 0.38 [1.000 ±.015] ± 0.08 [.300 ±.003] 7.62 ± 0.08 [.300 ±.003] 1.78 ± 0.08 [.070 ±.003] 75