PICAC TRAINING SCHEDULE

Transcription

1 Plumbing Industry Climate Action Centre 6/306 Albert Street Brunswick VIC 3056 T (03) F (03) training@picac.com.au PICAC TRAINING SCHEDULE JANUARY JUNE

2 22138VIC Certificate II in Plumbing (Preapprenticeship) A plumbing pre-apprenticeship will introduce you to the plumbing industry and make you more attractive to prospective employers. By completing a pre-apprenticeship you will gain: - Industry knowledge - Workplace exposure - Hands-on experience An application and interview based selection process is involved. Commencing Feb 17 Full time for 13 weeks (with a break for Easter) PICAC Contact PICAC to register your interest in this course and find out if you are eligible for a government funded position. *This course is delivered with Victorian and Commonwealth funding. Asbestos removal Class A Three day program designed to provide knowledge and practical skills for the safe removal of friable asbestos containing material. It covers Part 4.3 of the OHS Regulations and would meet the needs of removal personnel and supervisors to competently remove friable asbestos. Note: This program does not result in a licence to remove asbestos or asbestos containing materials. Cheques payable to PICAC 8.00am 4.30pm for three days Feb Apr 1 3 Jun 2 4 PICAC 0* $629 $740 Backflow prevention Commission and maintain backflow prevention devices Three day program designed to train plumbers in the commissioning, testing and repairing of backflow prevention devices. Participants must hold water supply registration and/or licence. for three days Feb Mar Apr May Jun 3 5 PICAC 0* $570 $640 Disconnect/reconnect fixed wire electrical systems Seven day course recommended for plumbers who are required to carry out electrical work relating to low voltage fixed electrical appliances associated with their plumbing work. It covers the skills and knowledge required to safely isolate and disconnect electrical appliances then reconnect and test appliances. This course does not cover rectifying faults. The units addressed in this course are; UEENEEP012A (composite appliances/ air conditioners) UEENEEP014A (water heaters) UEENEEP015A (motors) Participants may select two units. Note: external course assessment occurs one week after course completion Course cost includes one attempt at external assessment. Additional assessments will incur additional charge. Licence (REL Class 2) cost at participant expense pm 7.00pm for seven days Mar 3 6 and External course assessment dates Mar for seven days May 5 8 and External course assessment dates May PICAC 0* $739 $985 Energy efficient HVAC systems 1 This course is designed to increase your awareness of the importance of aiming for best practice in energy efficiency HVAC systems for the HVAC industry, for your clients and for the community in general. Cheques payable to AMCA. The course is delivered online at PICAC 0* $50 $100 Flashback Arrestor & Oxy-Acetylene Testing The OH&S act places a responsibility on employers and employees to ensure that the workplace is safe for all. Oxy-Acetylene welding and cutting can cause severe injury and damage if not maintained in a safe working condition. This short course has been developed to familiarise participants with: - Testing of Flashback Arrestors using an approved testing device - Testing of Oxygen and Acetylene hoses, regulators and handpieces. At the completion of the course the participants will have covered the operation of a flashback arrestor tester and testing requirements of oxy-acetylene equipment. Cheques payable to AMCA 9.00am 4.00pm Apr 3 PICAC 0* $50 $100

3 Install medical gas pipeline systems Three day program designed to provide participants with the skills and knowledge to safely install Medical Gas Pipeline Systems, which are essential for the treatment of patients in hospitals, medical centres and other treatment facilities. Cheques payable to PICAC 8.00am 4.30pm for 3 days Feb Apr 2 4 Jun 4 6 PICAC 0 $650 $760 Install split air conditioning systems block delivery Program designed to develop the skill and knowledge necessary to install split air conditioning systems with a capacity to 18 kilowatts. Participants must hold mechanical services registration and/or licence or be able to demonstrate current industry experience in this field. 8.00am 4.30pm for five days Apr 7 11 Holmesglen, Chadstone campus 0* $775 $1030 Thermostatic mixing valves (Commission and maintain heated water temperature control devices) Two day program designed to train plumbers to test, commission and maintain hot water temperature control devices, including thermostatic mixing valves in water services. Participants must hold water supply registration and/or licence. Feb Apr 8 9 May PICAC 0* $440 $550 Type A gas appliance servicing This course covers the skills and knowledge to identify, diagnose and remedy faults on domestic and commercial Type A gas appliances. Participants must hold gas registration and/or licence pm 7.00pm Mondays and Tuesdays for eight weeks Feb 17 Apr 8 Note: No training Monday 10 Mar May 5 Jun 24 Note: No training Monday 9 Jun PICAC 0* $2138 $2850 Type B gas appliance servicing This course covers the skills and knowledge to install, test, adjust, commission and service Type B gas appliances. Participants will learn to identify, diagnose and rectify system faults in Type B appliances. It is desirable that participants hold gas registration and/or licence. Participants with appropriate industry experience in this field are advised to seek approval from the Victorian Building Authority (VBA) prior to enrolling. Participants must hold a restricted electrical workers licence pm 7.00pm Wednesday and Thursdays for eight weeks Feb 19 Apr 10 May 7 Jun 26 PICAC 0* $2138 $2850 Welding Centre Please contact CEPUTEC for more information on welding programs. Open every Monday (including RDO) 7.00am 5.30pm Every Wednesday evening 5.30pm 8.30pm Commencing Feb 3 PICAC 0* Prices on application. Prices will vary depending on what level of ticket participant wishes to apply for and over what duration. Welding Electrofusion and Polybutt Welding A one day program that covers butt welding and the electrofusion welding of polyethelene (PE) plastic pipe and pipeline components under industrial conditions (in field and factory). Feb 3, Feb 17, Mar 17, Mar 31, Apr 14, May 5 May 19, Jun 2, Jun 16 PICAC 0* $520 $690

4 Green Plumber Block program Five day program offering fast track delivery of the Course in Green Plumbers Environmental Solutions (five core and two electives). for five days Jun and PICAC 0* $743 $990 Commercial hot water One day program enabling plumbers to provide recommendations and advice to clients on efficient commercial heated water systems including gas, electric, solar and/or heat pump heated water systems. Jun 24 Energy efficient plumbing clients to improve energy usage in domestic and commercial properties. Mar 19 Environmental plumbing inspections Half day program enabling plumbers to perform an environmental plumbing inspection and complete an inspection report for domestic buildings. 1.00pm 5.00pm May 6 PICAC 0* $128 $170 Geothermal heat pump systems One day program enabling plumbers to provide recommendations and advice to clients on the use of geothermal heat pump systems (ground source heat pumps) for heating and cooling to improve environmental sustainability. Jun 25 GreenPlumber Irrigation systems clients on the use of irrigation systems. Natural waste water treatment clients on the use of onsite natural wastewater treatment systems. Contact PICAC to register your interest in this course Contact PICAC to register your interest in this course Solar hot water clients on the selection and installation of solar heated water systems. Apr 15 Suburban pump systems One day program enabling plumbers to plan and size simple pump systems used to pump rainwater and greywater in suburban areas. Mar 4 Urban alternative water clients on the alternative sources of water available for urban use. May 20 Water conservation Half day program enabling plumbers to provide recommendations and advice to clients to reduce the use of water in domestic and commercial properties. It does not cover the use of alternative water sources such as rainwater, stormwater or recycled water. 8.30am 12.30pm May 6 PICAC 0* $128 $170

5 Boomlift Two day program where participants will be assessed for their boomlift licence. Licence cost at participant expense Feb 13 14, Mar 13 14, Apr May 15 16, Jun 12 13, PICAC 0* $360 $480 BSB41412 Certificate IV in OH&S This qualification will provide learning outcomes for participants to perform their role in OHS under supervision of an OHS Coordinator or OHS Manager. There are no prerequisite requirements for individual units of competency. Every Tuesday evening 5pm to 9pm (12 month course, school terms) Begins Feb 4 Submissions must be in by Jan 17 0* $750 $1000 BSB51312 Diploma of OH&S This qualification will provide learning outcomes for participants to perform their role in OHS as an OHS Manager, practitioner or senior officer. Prerequisite: Must have completed Certificate IV in OH&S Every Wednesday evening 5pm to 9pm (12 month course, school terms) Begins Feb 5 Submissions must be in by Jan 17 0* $750 $1000 Confined space entry Two day program providing participants with the skills and knowledge required to enter confined spaces using appropriate equipment. Feb 17 18, Mar 17 18, Apr 14 15, May 19 20, Jun PICAC 0* $300 $400 Confined space entry refresher One day program providing refresher training for confined space entry. Feb 19, Mar 19, Apr 16, May 21, Jun 18 PICAC 0* $150 $200 Construction Induction (CI card) One day program providing participants with basic instruction on OHS. Participants are required to bring photo ID. Course fee includes $30 Worksafe CI card fee Feb 12, Mar 12, Apr 9, May 14, Jun 18 PICAC 30* $195 $265 First Aid Level two Two day program that trains participants on the critical elements of initial response to an emergency in a range of settings. This is a practical, hands on course. Feb 27 28, Mar 27 28, May 29 30, Jun PICAC 0* $170 $230 First Aid Level two refresher One day program designed to refresh first aiders practical first aid skills. Feb 21, Mar 21, May 23, Jun 20 PICAC 0* $100 $125 First Aid Level three refresher One day program designed to refresh first aiders in advanced resuscitation techniques and use of a wide range of equipment. Apr 17 PICAC 0* $190 $255

6 Forklift Two day program where participants will be assessed for their forklift licence. Licence cost at participant expense Feb 6 7, Mar 6 7, Apr 3 4 May 8 9, Jun 5 6, PICAC 0* $360 $485 Safe work on roofs One day program designed to provide participants with OHS knowledge and skills to enable them to work safely on roofs using correct fall protection and appropriate anchor points. Feb 4, Mar 25, Apr 8, May 6, Jun 24 PICAC 0* $260 $345 Safety representatives course Five day program designed to train either the elected workplace health and safety representative or the deputy health and safety representative as per the requirements of the Occupational Health & Safety Act 2004 for five Tuesdays Feb 4, 11, 18, 25, Mar 4 May 6, 13, 20, 27, Jun 3 PICAC 0* $605 $805 Safety representatives refresher One day program designed to provide refresher training for health and safety representatives and/or deputy health and safety representatives as recommended under the Occupational Health & Safety Act Mar 18, Jun 17 PICAC 0* $105 $140 Scissorlift Half day program addressing all aspects of scissorlift operations. 7.15am 11.30am Feb 13, Mar 13, Apr 10, May 22, Jun 19 PICAC 0* $225 $300 Carry out work based risk control processes This course provides participants with the skills and knowledge to identify workplace hazards, assess risk, determine unacceptable risk and prepare a course of action as required by plumbing contractors. This unit is required by the Victorian Building Authority for registered plumbers who wish to seek their licence in any stream. It is an accredited unit of competency within the Certificate IV in Plumbing and Services. Participation in this course requires self directed study and home work. Regional participants welcome! Online training options available for participants at home. Contact PICAC for more details. 6.00pm 9.00pm Wednesday evenings for four weeks Feb 19, 26, Mar 5, 12 May 7, 14, 21, 28 PICAC 0* $225 $300 Establish legal and risk management requirements for small business This course provides participants with the skill and knowledge required to identify and establish a range of business structures and to comply with the regulatory, legal, taxation and insurance requirements of establishing and running a small business. This unit is required by the Victorian Building Authority for registered plumbers who wish to seek their licence in any stream. It is an accredited unit of competency within the Certificate IV in Plumbing and Services. Participation in this course requires self directed study and home work. Regional participants welcome! Online training options available for participants at home. Contact PICAC for more details. 6.00pm 9.00pm Thursday evenings for 10 weeks Feb 13, 20, 27, Mar 6, 13, 20, 27, Apr 3, 10, 17 May 29, Jun 5, 12, 19, 26, Jul 3, 10, 17, 24, 31 PICAC 0* $360 $480 Estimate and cost work This course provides participants with the skills and knowledge to estimate plumbing materials, labour and time requirements to complete plumbing jobs. This unit is required by the Victorian Building Authority for registered plumbers who wish to seek their licence in any stream. It is an accredited unit of competency within the Certificate IV in Plumbing and Services. Participation in this course requires self directed study and home work. Regional participants welcome! Online training options available for participants at home. Contact PICAC for more details. 6.00pm 9.00pm Tuesday evenings for five weeks Feb 18, 25, Mar 4, 11, 18 Jun 3, 10, 17, 24, Jul 1 PICAC 0* $270 $360

7 Mechanical Services licence level training (Design, size and layout heating and cooling systems) This course provides participants with the skills and knowledge to design, size and document the layout of heating and cooling systems (mechanical services) for multi floor structures. This unit is required by the Victorian Building Authority for registered plumbers who wish to seek their licence in Mechanical Services. It is an accredited unit of competency within the Certificate IV in Plumbing and Services. Participation in this course requires self directed study and home work. Regional participants welcome! Online training options available for participants at home. Contact PICAC for more details. Mondays for 10 weeks Feb 24, Mar 3, 17, 24, 31, Apr 7, 14, 28, May 5, 12 PICAC 0* $518 $690 Produce 2D architectural drawing using CAD software This four day course is designed to give learners the required skill and knowledge to produce 2D drawings using CAD software. This is an accredited unit of competency within the Certificate IV in Plumbing and Services and the Diploma of Fire Systems Design. for four days over four weeks Feb 10, 24, Mar 11, 24 May 12, 26, Jun 10, 23 PICAC 0* $800 $980 New courses coming soon! Roofing (licence level) Gas services (licence level) Water services (licence level) Express your interest in these courses for PICAC Contact PICAC for more information Regional participants welcome. Online training options available for participants at home. Calling for expressions of interest Introduction to REVIT and BIM Total Station Field use Express your interest in these courses for PICAC Contact PICAC for more information Annual testing This five week course is designed as an upskilling course for registered sprinkler fitters. 4.30pm 8.30pm Wednesday evenings for five weeks Mar 5, 12, 19, 26 Jun 4, 11, 18, 25 PICAC 0* NA NA Fire Sprinkler testing This course is designed as an upskilling course for registered sprinkler fitters. 4.30pm 8.30pm Tuesday evenings for four weeks Feb 4, 11, 18, 25 May 6, 13, 20, 27 PICAC 0* NA NA Inspect and Test Control and Indicating Equipment This two day course covers routine monthly and six monthly inspecting and testing of CIE s, such as Fire Indicator Panels. 7.30am 3.30pm Feb 7, 21 Mar 7, 21 May 9, 23 Jun 6, 20 PICAC 0* $400 $500 Special hazards fixed system testing and maintenance and fixed system installation and decommissioning This course is designed for registered sprinkler fitters and covers the competencies required for successful participants to apply for a qualified persons Extinguishing Agent Handling Licence category 2 and 3. Please note: Licence application needs to be made directly to the licensing authority. Course duration and price based on an individual having completed a Certificate III in Fire Protection after Contact PICAC for pre 1999 qualification pricing and course duration. 7.30am 4.00pm for four days over four weeks Feb 10, 24, Mar 11, 24 May 12, 26, Jun 10, 23 PICAC 0* $600 $720 Need to arrange a specific training date? We can organise a training date exclusively for your organisation s needs. We create client specific, customised training programmes! Contact PICAC for more information on or training@picac.com.au

8 Plumbing Industry Climate Action Centre 6/306 Albert Street Brunswick VIC 3056 T (03) F (03) E training@picac.com.au EXPRESSION OF INTEREST FORM Complete the following details and forward by training@picac.com.au or post to the above address. You will receive a letter of course confirmation. Please print clearly filling out this form. Use one form for each participant. PTEU member Master Plumber member AMCA member NFIA member Apprentice Yes, I am interested in training on RDOs Name Date of birth M F Occupation Company name Company address Personal address Post code Post code Preferred address for training related correspondence Company address Personal address Phone Mobile (MANDATORY FIELD) Member number Registration/Licence/Delta number Course name Course location Course date Course fee (GST inclusive) Payment method (please tick) Credit card Mastercard Visa Cheque Credit card number Name on card Expiry date Signature Please indicate if you need assistance or have learning difficulties with any of the following in a learning environment: Hearing Sight Language Reading Numeracy Other: Terms and Conditions An administration fee of $50 will apply to all Category A registrations if the participant fails to attend training, in line with the cancellation policy. The fee for Type A and Type B gas appliance and Disconnect/reconnect training courses is $200. Course dates and locations are subject to change. Eligibility for subsidised rates is at the discretion of PICAC. Subsidised training is only available for courses booked through PICAC. Privacy Policy We will not sell, distribute or lease your personal information to third parties unless we have your permission or are required by law. You may request details of personal information which we hold about you under the Data Protection Act If you would like a copy of the information held on you please contact training@picac.com.au. If you believe that any information we are holding on you is incorrect or incomplete, please contact us immediately, at the above address. For more information on our privacy policy please visit General PICAC Cancellation Policy PICAC reserves the right to cancel courses. Note: refunds will only be issued on the following basis: Full refund when 10 or more working days notice is given. A 50% refund when 4 9 days notice is given. No refund will apply if less than 4 days notice is given. Substitutions are acceptable but you must advise PICAC of names prior to the course commencement. A full refund will apply if PICAC cancels any program. For course specific cancellation policies please contact PICAC. Signature Employer signature (where applicable) If under 18 please get a parent/guardian to sign Date Date Date F Fire Industry courses I Industry training courses O OHS and high risk licence courses B Business development training courses I Green Plumbing Industry training courses Payment categories Category A Training participant is a fully financial PTEU member. May be registered in training course by self or employer. Category B Training participant is a Master Plumbers, AMCA or NFIA Association member. Category C Training participant is not a member of PTEU or Master Plumbers, AMCA, NFIA. Immediate family members (wives, husbands, de-facto partners and children) of PTEU members may be eligible for discounted training programs. Contact CEPUTEC on for more information. Training at PICAC is funded in whole or in part by Incolink, the construction industry s redundancy fund.!