HCC4020B/24B/40B HCF4020B/24B/40B
|
|
|
- Imogen Powers
- 7 years ago
- Views:
Transcription
1 HCC4020B/24B/40B HCF4020B/24B/40B RIPPLE-CARRY BINARY COUNTER/DIIDERS 4020B - 14 STAGE 4024B - 7 STAGE 4040B - 12 STAGE MEDIUM-SPEED OPERATION FULLY STATIC OPERATION COMMON RESET BUFFERED INPUTS AND OUTPUTS QUIESCENT CURRENT SPECIFIED TO 20 FOR HCC DEICE STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS 5, 10, AND 15 PARAMETRIC RATINGS INPUT CURRENT OF 100nA AT 18 AND. 25 C FOR HCC DEICE 100% TESTED FOR QUIESCENT CURRENT MEETS ALL REQUIREMENTS OF JEDEC TEN- TATIE STANDARD No. 13A, STANDARD SPECIFICATIONS FOR DESCRIPTION OF B SERIES CMOS DEICES DESCRIPTION The HCC4XXXB (extended temperature range) and HCF4XXXB (intermediate temperature range) are monolithic integrated circuits, available in 14- lead dual in-line for 4024B and 16-lead dual in-line for 4020B, 4040B plastic or ceramic package and plastic micropackage. EY (Plastic Package) M1 (Micro Package) F (Ceramic Package) C1 (Plastic Chip Carrier) ORDER CODES : HCC40XXBF HCF40XXBM1 HCF40XXBEY HCF40XXBC1 The HCC/HCF4020B, 4024B,and 4040B are ripplecarry binary counters. All counter stages are masterslave flip-flops. The state of a counter advances one count on the negative transition of each input pulse ; a high level on the RESET line resets the counter to its all zeros stage. Schmitt trigger action on the inputpulse line permits unlimited clock rise and fall times. All inputs and outputs are buffered. PIN CONNECTIONS 4020B 4024B 4040B March /11
2 HCC/HFC4020B/24B/40B FUNCTIONAL DIAGRAMS 4020B 4024B 4040B ABSOLUTE MAXIMUM RATINGS Symbol Parameter alue Unit DD * Supply oltage : HCC HCF 0.5 to to + 18 I Input oltage 0.5 to DD I I DC Input Current (any one input) ± 10 ma P tot Total Power Dissipation (per package) Dissipation per Output Transistor for T op = Full Package-temperature Range mw mw T op Operating Temperature : HCC HCF 55 to to+85 T stg Storage Temperature 65 to C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for external periods may affect device reliability. * All voltage values are refered to SS pin voltage. C C RECOMMENDED OPERATING CONDITIONS Symbol Parameter alue Unit DD Supply oltage : HCC HCF 3to18 3to15 I Input oltage 0 to DD T op Operating Temperature : HCC HCF 55 to to+85 C C 2/11
3 HCC/HCF4020B/24B/40B LOGIC DIAGRAMS 4020B 4040B 4024B 3/11
4 HCC/HFC4020B/24B/40B STATIC ELECTRICAL CHARACTERISTICS (over recommended operating conditions) Symbol I L OH OL IH IL I OH I OL I IH,I IL Parameter Quiescent Current Output High oltage Output Low oltage Input High oltage Input Low oltage Output Drive Current Output Sink Current Input Leakage Current HCC HCF HCC HCF HCC HCF HCC HCF Test Conditions alue I O I O DD T Low * 25 C T High * () () (µa) () Min. Max. Min. Typ. Max. Min. Max. 0/ / / / / / / / 5 < /10 < /15 < /0 < /0 < /0 < /4.5 < /9 < /13.5 < /0.5 < /1 < /1.5 < / / / / / / / / / / / / / / /18 18 ± 0.1 ±10 5 ± 0.1 ± 1 Any Input 0/15 15 ± 0.3 ±10 5 ± 0.3 ± 1 C I Input Capacitance Any Input pf *T Low= 55 C for HCC device : 40 C for HCF device. * THigh= C for HCC device : + 85 C for HCF device. The Noise Margin for both 1 and 0 level is : 1 min. with DD = 5, 2 min. with DD = 10, 2.5 min. with DD = 15. Unit µa ma ma µa 4/11
5 HCC/HCF4020B/24B/40B DYNAMIC ELECTRICAL CHARACTERISTICS (T amb =25 C, C L = 50pF, R L = 200kΩ, typical temperature coefficient for all DD = 0.3%/ C values, all input rise and fall time = 20ns). Symbol Parameter Test Conditions alue DD () Min. Typ. Max. INPUT-PULSE OPERATION t PLH,t PHL Propagation Delay Time (Ø to Q1 Out) t PLH,t PHL Propagation Delay Time Qn to Q n t TLH,t THL Transition Time t W Minimum Input Pulse Width ns t r,t f Input Pulse Rise and Fall Time Unlimited µs f max Maximum Clock Input Frequency MHz RESET OPERATION t PHL Propagation Delay Time ns t W Minimum Reset Pulse Width ns t rem Reset Removal Time ns Unit ns ns ns 5/11
6 HCC/HFC4020B/24B/40B Minimum Output Low (sink) Current Characteristics. Typical Output Low (source) Current Characteristics. Minimum Output High (source) Current Characteristics. Typical Output High (sink) Current Characteristics. Details of Typical Flip-flop Stage. 6/11
7 HCC/HCF4020B/24B/40B Plastic DIP16 (0.25) MECHANICAL DATA DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. a B b b D E e e F I L Z P001C 7/11
8 HCC/HFC4020B/24B/40B Ceramic DIP16/1 MECHANICAL DATA DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. A B D E e F G H L M N P Q P053D 8/11
9 HCC/HCF4020B/24B/40B SO16 (Narrow) MECHANICAL DATA DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. A a a b b C c1 45 (typ.) D E e e F G L M S 8 (max.) P013H 9/11
10 HCC/HFC4020B/24B/40B PLCC20 MECHANICAL DATA DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. A B D d d E e e F G M M P027A 10/11
11 HCC/HCF4020B/24B/40B Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specificationsmentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronicsproducts are not authorized foruse ascritical componentsin life support devices or systems without express written approval of SGS-THOMSON Microelectonics SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 11/11
HCC/HCF4032B HCC/HCF4038B
HCC/HCF4032B HCC/HCF4038B TRIPLE SERIAL ADDERS INERT INPUTS ON ALL ADDERS FOR SUM COMPLEMENTING APPLICATIONS FULLY STATIC OPERATION...DC TO 10MHz (typ.) @ DD = 10 BUFFERED INPUTS AND OUTPUTS SINGLE-PHASE
HCC/HCF4027B DUAL-J-K MASTER-SLAVE FLIP-FLOP
DUAL-J-K MASTER-SLAVE FLIP-FLOP. SET-RESET CAPABILITY STATIC FLIP-FLOP OPERATION - RETAINS STATE INDEFINITELY WITH CLOCK LEVEL EITHER HIGH OR LOW MEDIUM SPEED OPERATION - 16MHz (typ. clock toggle rate
. MEDIUM SPEED OPERATION - 8MHz (typ.) @ . MULTI-PACKAGE PARALLEL CLOCKING FOR HCC4029B HCF4029B PRESETTABLE UP/DOWN COUNTER BINARY OR BCD DECADE
HCC4029B HCF4029B PRESETTABLE UP/DOWN COUNTER BINARY OR BCD DECADE. MEDIUM SPEED OPERATION - 8MHz (typ.) @ CL = 50pF AND DD-SS = 10. MULTI-PACKAGE PARALLEL CLOCKING FOR SYNCHRONOUS HIGH SPEED OUTPUT RES-
HCC4541B HCF4541B PROGRAMMABLE TIMER
HCC4541B HCF4541B PROGRAMMABLE TIMER 16 STAGE BINARI COUNTER LOW SYMMETRICAL OUTPUT RESISTANCE, TYPICALLY 100 OHM AT DD = 15 OSCILLATOR FREQUENCY RANGE : DC TO 100kHz AUTO OR MASTER RESET DISABLES OSCIL-
HCF4081B QUAD 2 INPUT AND GATE
QUAD 2 INPUT AND GATE MEDIUM SPEED OPERATION : t PD = 60ns (Typ.) at 10 QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15 PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I = 100nA (MAX) AT DD = 18 T A = 25
HCF4070B QUAD EXCLUSIVE OR GATE
QUAD EXCLUSIE OR GATE MEDIUM-SPEED OPERATION t PHL = t PLH = 70ns (Typ.) at CL = 50 pf and DD = 10 QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15 PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I = 100nA
HCF4001B QUAD 2-INPUT NOR GATE
QUAD 2-INPUT NOR GATE PROPAGATION DELAY TIME: t PD = 50ns (TYP.) at V DD = 10V C L = 50pF BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20V
HCF4028B BCD TO DECIMAL DECODER
BCD TO DECIMAL DECODER BCD TO DECIMAL DECODING OR BINARY TO OCTAL DECODING HIGH DECODED OUTPUT DRIVE CAPABILITY "POSITIVE LOGIC" INPUTS AND OUTPUTS: DECODED OUTPUTS GO HIGH ON SELECTION MEDIUM SPEED OPERATION
HCF4056B BCD TO 7 SEGMENT DECODER /DRIVER WITH STROBED LATCH FUNCTION
BCD TO 7 SEGMENT DECODER /DRIVER WITH STROBED LATCH FUNCTION QUIESCENT CURRENT SPECIF. UP TO 20V OPERATION OF LIQUID CRYSTALS WITH CMOS CIRCUITS PROVIDES ULTRA LOW POWER DISPLAY. EQUIVALENT AC OUTPUT DRIVE
. HIGH SPEED .LOW POWER DISSIPATION .COMPATIBLE WITH TTL OUTPUTS M54HCT27 M74HCT27 TRIPLE 3-INPUT NOR GATE. tpd = 9 ns (TYP.
M54HCT27 M74HCT27 TRIPLE 3-INPUT NOR GATE. HIGH SPEED tpd = 9 ns (TYP.) AT VCC =5V.LOW POWER DISSIPATION I CC =1µA (MAX.) AT T A =25 C.COMPATIBLE WITH TTL OUTPUTS VIH = 2V (MIN.) VIL = 0.8V (MAX) OUTPUT
HCF4010B HEX BUFFER/CONVERTER (NON INVERTING)
HEX BUFFER/CONVERTER (NON INVERTING) PROPAGATION DELAY TIME: t PD = 50ns (Typ.) at V DD = 10V C L = 50pF HIGH TO LOW LEVEL LOGIC CONVERSION MULTIPLEXER: 1 TO 6 OR 6 TO 1 HIGH "SINK" AND "SOURCE" CURRENT
Obsolete Product(s) - Obsolete Product(s)
SYNCHRONOUS PROGRAMMABLE 4-BIT BINARY COUNTER WITH ASYNCHRONOUS CLEAR INTERNAL LOOK-AHEAD FOR FAST COUNTING CARRY OUTPUT FOR CASCADING SYNCHRONOUSLY PROGRAMMABLE LOW-POWER TTL COMPATIBILITY STANDARDIZED
.LOW POWER DISSIPATION .HIGH NOISE IMMUNITY M74HC154 4 TO 16 LINE DECODER/DEMULTIPLEXER. HIGH SPEED tpd = 15 ns (TYP.) at VCC =5V
. HIGH SPEED tpd = 15 ns (TYP.) at VCC =5V.LOW POWER DISSIPATION I CC =4µA (MAX.) at T A =25 C.HIGH NOISE IMMUNITY VNIH =VNIL =28%VCC (MIN.) OUTPUT DRIVE CAPABILITY 15 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE
Description. Table 1. Device summary. Order code Temperature range Package Packaging Marking
14-stage ripple carry binary counter/divider and oscillator Applications Automotive Industrial Computer Consumer Description Datasheet - production data Features Medium speed operation Common reset Fully
. HIGH SPEED .LOW POWER DISSIPATION .HIGH NOISE IMMUNITY M54/M74HC190 M54/M74HC191 4 BIT SYNCHRONOUS UP/DOWN COUNTERS. fmax = 48 MHz (TYP.
M54/M74HC190 M54/M74HC191 4 BIT SYNCHRONOUS UP/DOWN COUNTERS. HIGH SPEED fmax = 48 MHz (TYP.) AT VCC =5V.LOW POWER DISSIPATION I CC =4µA (MAX.) AT T A =25 C.HIGH NOISE IMMUNITY VNIH =VNIL =28%VCC (MIN.)
CD4027BC Dual J-K Master/Slave Flip-Flop with Set and Reset
October 1987 Revised March 2002 CD4027BC Dual J-K Master/Slave Flip-Flop with Set and Reset General Description The CD4027BC dual J-K flip-flops are monolithic complementary MOS (CMOS) integrated circuits
CD4001BC/CD4011BC Quad 2-Input NOR Buffered B Series Gate Quad 2-Input NAND Buffered B Series Gate
CD4001BC/CD4011BC Quad 2-Input NOR Buffered B Series Gate Quad 2-Input NAND Buffered B Series Gate General Description The CD4001BC and CD4011BC quad gates are monolithic complementary MOS (CMOS) integrated
SWITCH-MODE POWER SUPPLY CONTROLLER PULSE OUTPUT DC OUTPUT GROUND EXTERNAL FUNCTION SIMULATION ZERO CROSSING INPUT CONTROL EXTERNAL FUNCTION
SWITCH-MODE POWER SUPPLY CONTROLLER. LOW START-UP CURRENT. DIRECT CONTROL OF SWITCHING TRAN- SISTOR. COLLECTOR CURRENT PROPORTIONAL TO BASE-CURRENT INPUT REERSE-GOING LINEAR OERLOAD CHARACTERISTIC CURE
L293B L293E PUSH-PULL FOUR CHANNEL DRIVERS. OUTPUT CURRENT 1A PER CHANNEL PEAK OUTPUT CURRENT 2A PER CHANNEL (non repetitive) INHIBIT FACILITY
L293B L293E PUSH-PULL FOUR CHANNEL DRIVERS OUTPUT CURRENT 1A PER CHANNEL PEAK OUTPUT CURRENT 2A PER CHANNEL (non repetitive) INHIBIT FACILITY. HIGH NOISE IMMUNITY SEPARATE LOGIC SUPPLY OVERTEMPERATURE
CD4013BC Dual D-Type Flip-Flop
CD4013BC Dual D-Type Flip-Flop General Description The CD4013B dual D-type flip-flop is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P-channel enhancement mode transistors.
LF00AB/C SERIES VERY LOW DROP VOLTAGE REGULATORS WITH INHIBIT
LF00AB/C SERIES ERY LOW DROP OLTAGE REGULATORS WITH INHIBIT ERY LOW DROPOUT OLTAGE (5) ERY LOW QUIESCENT CURRENT (TYP. 50 µa IN OFF MODE, 500µA INON MODE) OUTPUT CURRENT UP TO 500 ma LOGIC-CONTROLLED ELECTRONIC
MM74HC273 Octal D-Type Flip-Flops with Clear
MM74HC273 Octal D-Type Flip-Flops with Clear General Description The MM74HC273 edge triggered flip-flops utilize advanced silicon-gate CMOS technology to implement D-type flipflops. They possess high noise
CD40174BC CD40175BC Hex D-Type Flip-Flop Quad D-Type Flip-Flop
Hex D-Type Flip-Flop Quad D-Type Flip-Flop General Description The CD40174BC consists of six positive-edge triggered D- type flip-flops; the true outputs from each flip-flop are externally available. The
MM74HC174 Hex D-Type Flip-Flops with Clear
Hex D-Type Flip-Flops with Clear General Description The MM74HC174 edge triggered flip-flops utilize advanced silicon-gate CMOS technology to implement D-type flipflops. They possess high noise immunity,
CD4027BM CD4027BC Dual J-K Master Slave Flip-Flop with Set and Reset
CD4027BM CD4027BC Dual J-K Master Slave Flip-Flop with Set and Reset General Description These dual J-K flip-flops are monolithic complementary MOS (CMOS) integrated circuits constructed with N- and P-
STP6N60FI N - CHANNEL ENHANCEMENT MODE POWER MOS TRANSISTOR
N - CHANNEL ENHANCEMENT MODE POWER MOS TRANSISTOR TYPE VDSS RDS(on) ID STP6N60FI 600 V < 1.2 Ω 3.8 A TYPICAL R DS(on) =1Ω AVALANCHE RUGGED TECHNOLOGY 100% AVALANCHE TESTED REPETITIVE AVALANCHE DATA AT
LM134-LM234 LM334 THREE TERMINAL ADJUSTABLE CURRENT SOURCES. OPERATES from 1V to 40V
LM134-LM234 LM334 THREE TERMINAL USTABLE CURRENT SOURCES OPERATES from 1 to 40. 0.02% CURRENT REGULATION PROGRAMMABLE from 1µA to 10mA ±3% INITIAL ACCURACY DESCRIPTION The LM134/LM234/LM334 are 3-terminal
TL074 TL074A - TL074B
A B LOW NOISE JFET QUAD OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT LOW NOISE e n = 15nV/ Hz (typ) OUTPUT SHORTCIRCUIT PROTECTION
LM833 LOW NOISE DUAL OPERATIONAL AMPLIFIER
LOW NOISE DUAL OPERATIONAL AMPLIFIER LOW VOLTAGE NOISE: 4.5nV/ Hz HIGH GAIN BANDWIDTH PRODUCT: 15MHz HIGH SLEW RATE: 7V/µs LOW DISTORTION:.2% EXCELLENT FREQUENCY STABILITY ESD PROTECTION 2kV DESCRIPTION
CD4001BC/CD4011BC Quad 2-Input NOR Buffered B Series Gate Quad 2-Input NAND Buffered B Series Gate
Quad 2-Input NOR Buffered B Series Gate Quad 2-Input NAND Buffered B Series Gate General Description The CD4001BC and CD4011BC quad gates are monolithic complementary MOS (CMOS) integrated circuits cotructed
CD4013BC Dual D-Type Flip-Flop
Dual D-Type Flip-Flop General Description The CD4013B dual D-type flip-flop is a monolithic complementary MOS (CMOS) integrated circuit cotructed with N- and P-channel enhancement mode traistors. Each
TDA2822 DUAL POWER AMPLIFIER SUPPLY VOLTAGE DOWN TO 3 V LOW CROSSOVER DISTORSION LOW QUIESCENT CURRENT BRIDGE OR STEREO CONFIGURATION
TDA2822 DUAL POER AMPLIFIER SUPPLY VOLTAGE DON TO 3 V. LO CROSSOVER DISTORSION LO QUIESCENT CURRENT BRIDGE OR STEREO CONFIGURATION DESCRIPTION The TDA2822 is a monolithic integrated circuit in 12+2+2 powerdip,
CD4043BC CD4044BC Quad 3-STATE NOR R/S Latches Quad 3-STATE NAND R/S Latches
CD4043BC CD4044BC Quad 3-STATE NOR R/S Latches Quad 3-STATE NAND R/S Latches General Description The CD4043BC are quad cross-couple 3-STATE CMOS NOR latches, and the CD4044BC are quad cross-couple 3- STATE
TL084 TL084A - TL084B
A B GENERAL PURPOSE JFET QUAD OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORTCIRCUIT PROTECTION HIGH INPUT IMPEDANCE
.OPERATING SUPPLY VOLTAGE UP TO 46 V
L298 DUAL FULL-BRIDGE DRIVER.OPERATING SUPPLY VOLTAGE UP TO 46 V TOTAL DC CURRENT UP TO 4 A. LOW SATURATION VOLTAGE OVERTEMPERATURE PROTECTION LOGICAL "0" INPUT VOLTAGE UP TO 1.5 V (HIGH NOISE IMMUNITY)
MM74HC14 Hex Inverting Schmitt Trigger
MM74HC14 Hex Inverting Schmitt Trigger General Description The MM74HC14 utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as
HEF4011B. 1. General description. 2. Features and benefits. 3. Ordering information. 4. Functional diagram. Quad 2-input NAND gate
Rev. 6 10 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a quad 2-input NAND gate. The outputs are fully buffered for the highest noise
ADJUSTABLE VOLTAGE AND CURRENT REGULATOR
L200 ADJUSTABLE VOLTAGE AND CURRENT REGULATOR ADJUSTABLE OUTPUT CURRENT UP TO 2 A (GUARANTEED UP TO Tj = 150 C) ADJUSTABLE OUTPUT VOLTAGE DOWN TO 2.85 V INPUT OVERVOLTAGE PROTECTION (UP TO 60 V, 10 ms)
STP80NF55-08 STB80NF55-08 STB80NF55-08-1 N-CHANNEL 55V - 0.0065 Ω - 80A D2PAK/I2PAK/TO-220 STripFET II POWER MOSFET
STP80NF55-08 STB80NF55-08 STB80NF55-08-1 N-CHANNEL 55V - 0.0065 Ω - 80A D2PAK/I2PAK/TO-220 STripFET II POWER MOSFET TYPE V DSS R DS(on) I D STB80NF55-08/-1 STP80NF55-08 55 V 55 V
MM74HCT373 MM74HCT374 3-STATE Octal D-Type Latch 3-STATE Octal D-Type Flip-Flop
3-STATE Octal D-Type Latch 3-STATE Octal D-Type Flip-Flop General Description The MM74HCT373 octal D-type latches and MM74HCT374 Octal D-type flip flops advanced silicongate CMOS technology, which provides
INTEGRATED CIRCUITS. 74LVC08A Quad 2-input AND gate. Product specification IC24 Data Handbook. 1997 Jun 30
INTEGRATED CIRCUITS IC24 Data Handbook 1997 Jun 30 FEATURES Wide supply voltage range of 1.2 V to 3.6 V In accordance with JEDEC standard no. 8-1A Inputs accept voltages up to 5.5 V CMOS low power consumption
L78M00 SERIES POSITIVE VOLTAGE REGULATORS. www.tvsat.com.pl
SERIES POSITIVE VOLTAGE REGULATORS OUTPUT CURRENT TO 0.5A OUTPUT VOLTAGES OF 5; 6; 8; 9; 10; 12; 15; 18; 20; 24V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION OUTPUT TRANSISTOR SOA PROTECTION DESCRIPTION
L297 STEPPER MOTOR CONTROLLERS
L297 STEPPER MOTOR CONTROLLERS NORMAL/WAVE DRIVE HALF/FULL STEP MODES CLOCKWISE/ANTICLOCKWISE DIRECTION SWITCHMODE LOAD CURRENT REGULA- TION PROGRAMMABLE LOAD CURRENT FEW EXTERNAL COMPONENTS RESET INPUT
HEF4021B. 1. General description. 2. Features and benefits. 3. Ordering information. 8-bit static shift register
Rev. 10 21 March 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is an (parallel-to-serial converter) with a synchronous serial data input (DS), a clock
MM74C74 Dual D-Type Flip-Flop
Dual D-Type Flip-Flop General Description The MM74C74 dual D-type flip-flop is a monolithic complementary MOS (CMOS) integrated circuit cotructed with N- and P-channel enhancement traistors. Each flip-flop
ULN2801A, ULN2802A, ULN2803A, ULN2804A
ULN2801A, ULN2802A, ULN2803A, ULN2804A Eight Darlington array Datasheet production data Features Eight Darlington transistors with common emitters Output current to 500 ma Output voltage to 50 V Integral
TDA2040. 20W Hi-Fi AUDIO POWER AMPLIFIER
20W Hi-Fi AUDIO POWER AMPLIFIER DESCRIPTION The TDA2040 is a monolithic integrated circuit in Pentawatt package, intended for use as an audio class AB amplifier. Typically it provides 22W output power
Symbol Parameter Value Unit IAR Avalanche Current, Repetitive or Not-Repetitive
BUZ11 N - CHANNEL 50V - 0.03Ω - 30A -TO-220 STripFET POWER MOSFET TYPE V DSS R DS(on) I D BUZ11 50 V < 0.04 Ω 30 A TYPICAL R DS(on) = 0.03 Ω AVALANCHE RUGGED TECHNOLOGY 100% AVALANCHE TESTED HIGH CURRENT
74LS193 Synchronous 4-Bit Binary Counter with Dual Clock
74LS193 Synchronous 4-Bit Binary Counter with Dual Clock General Description The DM74LS193 circuit is a synchronous up/down 4-bit binary counter. Synchronous operation is provided by having all flip-flops
MM74HC4538 Dual Retriggerable Monostable Multivibrator
MM74HC4538 Dual Retriggerable Monostable Multivibrator General Description The MM74HC4538 high speed monostable multivibrator (one shots) is implemented in advanced silicon-gate CMOS technology. They feature
4-bit binary full adder with fast carry CIN + (A1 + B1) + 2(A2 + B2) + 4(A3 + B3) + 8(A4 + B4) = = S1 + 2S2 + 4S3 + 8S4 + 16COUT
Rev. 03 11 November 2004 Product data sheet 1. General description 2. Features The is a high-speed Si-gate CMOS device and is pin compatible with low power Schottky TTL (LSTTL). The is specified in compliance
SG2525A SG3525A REGULATING PULSE WIDTH MODULATORS
SG2525A SG3525A REGULATING PULSE WIDTH MODULATORS 8 TO 35 V OPERATION 5.1 V REFERENCE TRIMMED TO ± 1 % 100 Hz TO 500 KHz OSCILLATOR RANGE SEPARATE OSCILLATOR SYNC TERMINAL ADJUSTABLE DEADTIME CONTROL INTERNAL
DM74LS193 Synchronous 4-Bit Binary Counter with Dual Clock
September 1986 Revised March 2000 DM74LS193 Synchronous 4-Bit Binary Counter with Dual Clock General Description The DM74LS193 circuit is a synchronous up/down 4-bit binary counter. Synchronous operation
TDA4605 CONTROL CIRCUIT FOR SWITCH MODE POWER SUPPLIES USING MOS TRANSISTORS
CONTROL CIRCUIT FOR SWITCH MODE POWER SUPPLIES USING MOS TRANSISTORS Fold-Back Characteristic provides Overload Protection for External Diodes Burst Operation under Short-Circuit and no Load Conditions
DM74LS191 Synchronous 4-Bit Up/Down Counter with Mode Control
August 1986 Revised February 1999 DM74LS191 Synchronous 4-Bit Up/Down Counter with Mode Control General Description The DM74LS191 circuit is a synchronous, reversible, up/ down counter. Synchronous operation
Symbol Parameter Value Unit V DS Drain-source Voltage (V GS =0) 50 V V DGR Drain- gate Voltage (R GS =20kΩ) 50 V
BUZ71A N - CHANNEL 50V - 0.1Ω - 13A TO-220 STripFET POWER MOSFET TYPE V DSS R DS(on) I D BUZ71A 50 V < 0.12 Ω 13 A TYPICAL RDS(on) = 0.1 Ω AVALANCHE RUGGED TECHNOLOGY 100% AVALANCHE TESTED HIGH CURRENT
CD4040BC, 12-Stage Ripple Carry Binary Counters CD4060BC, 14-Stage Ripple Carry Binary Counters
CD4040BC, 12-Stage Ripple Carry Binary Counters CD4060BC, 14-Stage Ripple Carry Binary Counters Features Wide supply voltage range: 3.0V to 15V High noise immunity: 0.45 V DD (Typ.) Low power TTL compatibility:
1-of-4 decoder/demultiplexer
Rev. 6 1 April 2016 Product data sheet 1. General description 2. Features and benefits 3. Applications The contains two 1-of-4 decoders/demultiplexers. Each has two address inputs (na0 and na1, an active
MC34063A MC34063E DC-DC CONVERTER CONTROL CIRCUITS
MC34063A MC34063E DC-DC CONVERTER CONTROL CIRCUITS OUTPUT SWITCH CURRENT IN EXCESS OF 1.5A 2% REFERENCE ACCURACY LOW QUIESCENT CURRENT: 2.5mA (TYP.) OPERATING FROM 3V TO 40V FREQUENCY OPERATION TO 100KHz
Symbol Parameter Value Unit V i-o Input-output Differential Voltage 40 V I O Output Current Intenrally Limited Top
LM117/217 LM317 1.2V TO 37V VOLTAGE REGULATOR OUTPUT VOLTAGE RANGE : 1.2 TO 37V OUTPUT CURRENT IN EXCESS OF 1.5A 0.1% LINE AND LOAD REGULATION FLOATING OPERATION FOR HIGH VOLTAGES COMPLETE SERIES OF PROTECTIONS
14-stage ripple-carry binary counter/divider and oscillator
Rev. 8 25 March 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a with three oscillator terminals (RS, REXT and CEXT), ten buffered outputs (Q3 to
L4940 series VERY LOW DROP 1.5 A REGULATORS
L4940 series VERY LOW DROP 1.5 A REGULATORS PRECISE 5 V, 8.5 V, 10 V, 12 V OUTPUTS LOW DROPOUT VOLTAGE (500 typ at 1.5A) VERY LOW QUIESCENT CURRENT THERMAL SHUTDOWN SHORT CIRCUIT PROTECTION REVERSE POLARITY
HEF4013B. 1. General description. 2. Features and benefits. 3. Applications. 4. Ordering information. Dual D-type flip-flop
Rev. 9 10 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Applications The is a dual D-type flip-flop that features independent set-direct input (SD), clear-direct input
DM74LS151 1-of-8 Line Data Selector/Multiplexer
1-of-8 Line Data Selector/Multiplexer General Description This data selector/multiplexer contains full on-chip decoding to select the desired data source. The DM74LS151 selects one-of-eight data sources.
L4970A 10A SWITCHING REGULATOR
10A SWITCHING REGULATOR 10A OUTPUT CURRENT 5.1 TO 40 OUTPUT OLTAGE RANGE 0 TO 90% DUTY CYCLE RANGE INTERNAL FEED-FORWARD LINE REGULA- TION INTERNAL CURRENT LIMITING PRECISE 5.1 ± 2% ON CHIP REFERENCE RESET
STP62NS04Z N-CHANNEL CLAMPED 12.5mΩ - 62A TO-220 FULLY PROTECTED MESH OVERLAY MOSFET
N-CHANNEL CLAMPED 12.5mΩ - 62A TO-220 FULLY PROTECTED MESH OVERLAY MOSFET TYPE V DSS R DS(on) I D STP62NS04Z CLAMPED
LM134-LM234-LM334. Three terminal adjustable current sources. Features. Description
Three terminal adjustable current sources Features Operates from 1V to 40V 0.02%/V current regulation Programmable from 1µA to 10mA ±3% initial accuracy Description The LM134/LM234/LM334 are 3-terminal
DM74LS157 DM74LS158 Quad 2-Line to 1-Line Data Selectors/Multiplexers
September 1986 Revised April 2000 DM74LS157 DM74LS158 Quad 2-Line to 1-Line Data Selectors/Multiplexers General Description These data selectors/multiplexers contain inverters and drivers to supply full
Quad 2-input NAND Schmitt trigger
Rev. 9 15 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Applications The is a quad two-input NAND gate. Each input has a Schmitt trigger circuit. The gate switches
DDSL01. Secondary protection for DSL lines. Features. Description
Secondary protection for DSL lines Features Stand off voltage: 30 V Surge capability: I pp = 30 A 8/20 µs Low capacitance device: 4.5 pf at 2 V RoHS package Low leakage current: 0.5 µa at 25 C 3 2 Description
DM7474 Dual Positive-Edge-Triggered D-Type Flip-Flops with Preset, Clear and Complementary Outputs
DM7474 Dual Positive-Edge-Triggered D-Type Flip-Flops with Preset, Clear and Complementary Outputs General Description This device contains two independent positive-edge-triggered D-type flip-flops with
BUX48/48A BUV48A/V48AFI
BUX48/48A BU48A/48AFI HIGH POWER NPN SILICON TRANSISTORS STMicroelectronics PREFERRED SALESTYPES NPN TRANSISTOR HIGH OLTAGE CAPABILITY HIGH CURRENT CAPABILITY FAST SWITCHING SPEED APPLICATIONS SWITCH MODE
74VHC574 Octal D-Type Flip-Flop with 3-STATE Outputs
74HC574 Octal D-Type Flip-Flop with 3-STATE Outputs General Description Ordering Code: March 1993 Revised May 2005 The HC574 is an advanced high speed CMOS octal flipflop with 3-STATE output fabricated
STW34NB20 N-CHANNEL 200V - 0.062 Ω - 34A TO-247 PowerMESH MOSFET
N-CHANNEL 200V - 0.062 Ω - 34A TO-247 PowerMESH MOSFET Table 1. General Features Figure 1. Package Type V DSS R DS(on) I D STW34NB20 200 V < 0.075 Ω 34 A FEATURES SUMMARY TYPICAL R DS(on) = 0.062 Ω EXTREMELY
L7800 SERIES POSITIVE VOLTAGE REGULATORS
SERIES POSITIVE VOLTAGE REGULATORS OUTPUT CURRENT UP TO 1.5 A OUTPUT VOLTAGES OF 5; 5.2; 6; 8; 8.5; 9; 12; 15; 18; 24V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION OUTPUT TRANSITION SOA PROTECTION
IRFP450. N - CHANNEL 500V - 0.33Ω - 14A - TO-247 PowerMESH MOSFET
IRFP450 N - CHANNEL 500V - 0.33Ω - 14A - TO-247 PowerMESH MOSFET TYPE V DSS R DS(on) I D IRFP450 500 V < 0.4 Ω 14 A TYPICAL R DS(on) = 0.33 Ω EXTREMELY HIGH dv/dt CAPABILITY 100% AVALANCHE TESTED VERY
TDA8174A TDA8174AW VERTICAL DEFLECTION CIRCUIT RAMP GENERATOR INDEPENDENT AMPLITUDE ADJUSTEMENT BUFFER STAGE POWER AMPLIFIER
TDA87A TDA87AW VERTICAL DEFLECTION CIRCUIT RAMP INDEPENDENT AMPLITUDE ADJUSTEMENT BUFFER STAGE POWER AMPLIFIER. FLYBACK THERMAL PROTECTION INTERNAL REFERENCE VOLTAGE DECOU- PLING MULTIWATT (Plastic Package)
IRF830. N - CHANNEL 500V - 1.35Ω - 4.5A - TO-220 PowerMESH MOSFET
IRF830 N - CHANNEL 500V - 1.35Ω - 4.5A - TO-220 PowerMESH MOSFET TYPE V DSS R DS(on) I D IRF830 500 V < 1.5 Ω 4.5 A TYPICAL R DS(on) = 1.35 Ω EXTREMELY HIGH dv/dt CAPABILITY 100% AVALANCHE TESTED VERY
STW20NM50 N-CHANNEL 550V @ Tjmax - 0.20Ω - 20ATO-247 MDmesh MOSFET
N-CHANNEL 550V @ Tjmax - 0.20Ω - 20ATO-247 MDmesh MOSFET TYPE V DSS (@Tjmax) R DS(on) I D STW20NM50 550V < 0.25Ω 20 A TYPICAL R DS (on) = 0.20Ω HIGH dv/dt AND AVALANCHE CAPABILITIES 100% AVALANCHE TESTED
DM74157 Quad 2-Line to 1-Line Data Selectors/Multiplexers
DM74157 Quad 2-Line to 1-Line Data Selectors/Multiplexers General Description These data selectors/multiplexers contain inverters and drivers to supply full on-chip data selection to the four out-put gates.
IRF740 N-CHANNEL 400V - 0.46Ω - 10A TO-220 PowerMESH II MOSFET
N-CHANNEL 400V - 0.46Ω - 10A TO-220 PowerMESH II MOSFET TYPE V DSS R DS(on) I D IRF740 400 V < 0.55 Ω 10 A TYPICAL R DS (on) = 0.46Ω EXCEPTIONAL dv/dt CAPABILITY 100% AVALANCHE TESTED LOW GATE CHARGE VERY
Description. Table 1. Device summary. Order code Temperature range Package Packing Marking
8-bit shift register with output latches (3-state) Applicatio Datasheet - production data SO16 TSSOP16 Automotive Industrial Computer Coumer Features High speed: f MAX = 59 MHz (typ.) at V CC = 6 V Low
8-bit binary counter with output register; 3-state
Rev. 3 24 February 2016 Product data sheet 1. General description The is an 8-bit binary counter with a storage register and 3-state outputs. The storage register has parallel (Q0 to Q7) outputs. The binary
ST202 5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS
5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS SUPPLY VOLTAGE RANGE: 4.5 TO 5.5V SUPPLY CURRENT NO LOAD (TYP): 1.5mA TRASMITTER OUTPUT VOLTAGE SWING (TYP): ± 9V TRANSITION SLEW RATE (TYP.): 12V/µs
DATA SHEET. HEF40193B MSI 4-bit up/down binary counter. For a complete data sheet, please also download: INTEGRATED CIRCUITS
INTEGRATED CIRCUITS DATA SHEET For a complete data sheet, please also download: The IC04 LOCMOS HE4000B Logic Family Specifications HEF, HEC The IC04 LOCMOS HE4000B Logic Package Outlines/Information HEF,
DM74LS169A Synchronous 4-Bit Up/Down Binary Counter
Synchronous 4-Bit Up/Down Binary Counter General Description This synchronous presettable counter features an internal carry look-ahead for cascading in high-speed counting applications. Synchronous operation
TS555. Low-power single CMOS timer. Description. Features. The TS555 is a single CMOS timer with very low consumption:
Low-power single CMOS timer Description Datasheet - production data The TS555 is a single CMOS timer with very low consumption: Features SO8 (plastic micropackage) Pin connections (top view) (I cc(typ)
CD4093BM CD4093BC Quad 2-Input NAND Schmitt Trigger
CD4093BM CD4093BC Quad 2-Input NAND Schmitt Trigger General Description The CD4093B consists of four Schmitt-trigger circuits Each circuit functions as a 2-input NAND gate with Schmitt-trigger action on
Order code Temperature range Package Packaging
ST485B ST485C Low power RS-485/RS-422 transceiver Features Low quiescent current: 300 µa Designed for RS-485 interface application - 7 V to 12 V common mode input voltage range Driver maintains high impedance
NTE2053 Integrated Circuit 8 Bit MPU Compatible A/D Converter
NTE2053 Integrated Circuit 8 Bit MPU Compatible A/D Converter Description: The NTE2053 is a CMOS 8 bit successive approximation Analog to Digital converter in a 20 Lead DIP type package which uses a differential
DM74LS112A Dual Negative-Edge-Triggered Master-Slave J-K Flip-Flop with Preset, Clear, and Complementary Outputs
August 1986 Revised March 2000 DM74LS112A Dual Negative-Edge-Triggered Master-Slave J-K Flip-Flop with Preset, Clear, and Complementary General Description This device contains two independent negative-edge-triggered
L78MxxAB L78MxxAC. Precision 500 ma regulators. Features. Description
L78MxxAB L78MxxAC Precision 500 ma regulators Features Output current to 0.5 A Output voltages of 5; 6; 8; 9; 10; 12; 15; 18; 24 V Thermal overload protection Short circuit protection Output transition
74HC393; 74HCT393. Dual 4-bit binary ripple counter
Rev. 6 3 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The 74HC393; 7474HCT393 is a dual 4-stage binary ripple counter. Each counter features
MM74C150 MM82C19 16-Line to 1-Line Multiplexer 3-STATE 16-Line to 1-Line Multiplexer
MM74C150 MM82C19 16-Line to 1-Line Multiplexer 3-STATE 16-Line to 1-Line Multiplexer General Description The MM74C150 and MM82C19 multiplex 16 digital lines to 1 output. A 4-bit address code determines
74HC377; 74HCT377. 1. General description. 2. Features and benefits. 3. Ordering information
Rev. 4 24 February 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is an octal positive-edge triggered D-type flip-flop. The device features clock (CP)
74AC139 74ACT139 Dual 1-of-4 Decoder/Demultiplexer
Dual 1-of-4 Decoder/Demultiplexer General Description The AC/ACT139 is a high-speed, dual 1-of-4 decoder/ demultiplexer. The device has two independent decoders, each accepting two inputs and providing
74HC175; 74HCT175. Quad D-type flip-flop with reset; positive-edge trigger
Rev. 5 29 January 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a quad positive-edge triggered D-type flip-flop with individual data inputs (Dn)
CD4008BM CD4008BC 4-Bit Full Adder
CD4008BM CD4008BC 4-Bit Full Adder General Description The CD4008B types consist of four full-adder stages with fast look-ahead carry provision from stage to stage Circuitry is included to provide a fast
3-input EXCLUSIVE-OR gate. The 74LVC1G386 provides a 3-input EXCLUSIVE-OR function.
Rev. 02 3 September 2007 Product data sheet 1. General description The provides a 3-input EXCLUSIVE-OR function. The input can be driven from either 3.3 or 5 V devices. This feature allows the use of these
Description. Table 1. Device summary
2 A positive voltage regulator IC Description Datasheet - production data Features TO-220 Output current up to 2 A Output voltages of 5; 7.5; 9; 10; 12; 15; 18; 24 V Thermal protection Short circuit protection