Series NCM. Air Cylinder. Stainless Steel Body Cylinders 7/16", 9/16", 3/4", 7/8", 1-1/16", 1-1/4", 1-1/2", 2" Bore

Transcription

1 CT.ID2-2 ir Cylinder Series CM Stainless Steel ody Cylinders 7/16", 9/16", 3/4", 7/8", 1-1/16", 1-1/4", 1-1/2", 2" ore ow available in 7/16" and 9/16" bore Double Rod/Double End Mounting on-rotating Rod ption uto Switch Capable Standard type ctuation Style uto switch capable onrotating rod ith bumper ore size Standard stroke Double acting Single rod 44 (7/16") 56 (9/16") 88 (7/8") 2 (2") [ore size 44/56] 5 (1/2"), 1 (1"),, 2 (2"), 25 (2-1/2"), 3 (3"), 4 (4") [ore size 75 and above] 5 (1/2"), 1 (1"),, 2 (2"), 25 (2-1/2"), 3 (3"), 4 (4"), 6 (6") Double acting Double rod 88 (7/8") 2 (2") 5 (1/2"), 1 (1"),, 2 (2"), 25 (2-1/2"), 3 (3"), 4 (4"), 6 (6") Single acting Single rod 88 (7/8") 5 (1/2"), 1 (1"), 2 (2"), 3 (3"), 4 (4"), 5 (5") 6 (6")

2 ir Cylinder Series CM ow available in 8 different bore sizes, 7/16" to 2". 5 ctuation options available: Double cting, Single Rod Double cting, Double Rod on-rotating Rod Single cting, Spring Return Single cting, Spring Extend wide variety of mounting configurations: ront ose Mount Rear Pivot Mount Double End Mount lock Mount oot Mount (optional brackets) Chrome plated carbon steel piston rod improves corrosion resistance. Stainless steel 34 is available for further protection. vailable bumper for increased kinetic energy absorption, increased life cycles, and decreased noise. Piston is crimped to rod to achieve tighter clearances and reduce piston rod deflection. Chromated aluminum piston improves corrosion resistance. Magnetic actuated limit switches are available as a standard option. Seal, wear ring, and polished stainless steel tube work together to absorb side load and decrease overall friction, ensuring long lasting service life. (ear ring used on 3/4" bore and larger.) ull port design increases cylinder response. Rolled threads for increased strength. Clear anodized end covers provide long lasting protection against corrosion. Pre-lubricated at the factory means that the CM does not require a lubricated air system. eatures 1

3 Series CM ir Cylinder Model Selection Step 1 btain the bore of the cylinder tube. Refer to Graph (1) and (2). Determine the load factor in accordance with the purpose. Purpose of operation oad factor η Static operation (Clamping, ow-speed vise crimping, etc.) Dynamic operation Horizontal movement of load on guide Vertical and horizontal movement of the load.7 or less (7% or less) 1 or less (1% or less).5 or less (5% or less) ote) ote) If it is particularly necessary to operate at high speeds, the load rate must be reduced further. (In the graph, it is possible to select a load rate of.4,.3,.2 or less.) Determine the operating pressure. Generally, set the regulator to 85% of the source air pressure. (In the graph, a selection between.2 MPa and.8 MPa is possible.) Determine the direction in which the cylinder force will be used. Extending side Refer to Graph (1). Retracting side Refer to Graph (2). ote) If the same load is applied both for pushing and pulling in a horizontal operation, set the direction to the pulling side. Step 3 Step 4 The aspects indicated below may need to be taken into consideration, depending on how the cylinder is operated. If a lateral load is applied to the piston rod: Verify in Graph (5) whether the lateral load is within an allowable range. hen using a cylinder with a relatively long stroke, if a buckling force acts on the piston rod or the cylinder tube, verify in the table whether the stroke or the operating pressure is within a safe range. btain the cylinder s air consumption and its required air volume. btain the air consumption selecting a compressor and for calculating the running cost and the required (Graph (6) to (7)) that is necessary for selecting a compressor and for calculating the running cost and the required air volume (Graph (8)) that is necessary for selecting equipment such as an air filter or a regulator, or the size of the piping upstream. Step 2 Take the impact at the stroke end into consideration. hen an external stopper (shock absorber, etc.) is provided to absorb the impact, select a stopper with sufficient absorption capacity. Stopping the piston with the cylinder without a stopper: Verify in Graph (3) to (4) the absorption capacity of the cushion that is enclosed in the cylinder. umper Urethane rubber is used for preventing metal-tometal contact between the piston and the cover. ront matter 1

4 Model Selection Step 1 btain the bore of the cylinder tube. Refer to Graph (1) and (2). Graph (1) Extending Side Cylinder orce (Double acting cylinder) Graph (2) Retracting Side Cylinder orce (Double acting cylinder) 1 1. Cylinder force (lbf) 1 CM2 CM15 CM125 CM16 CM88 CM75 Cylinder force (lbf) 1. CM2 CM15 CM125 CM16 CM88 CM75 CM56 1 CM44 1. CM56 CM44 perating pressure (PSI) oad factor (n) perating pressure (PSI) oad factor (n) (Example) P = 75 PSI (Example) P = 75 PSI = 9 lbs P = 75 PSI ig. (1) Example 1: If the minimum force of 85 lbf is necessary to keep the workpiece pressed as shown in ig. (1), because this is the extending side, use Graph (1) to determine the load factor of.7 and the operating pressure of 75 PSI. Then, seek the point at which the cylinder force of 85 lbf intersects, and this will result in a bore size of 1.5 inches. ig. (2) = ig. (3) 1 lbs Example 2: To move a load with a 9 lbf weight horizontally on a guide as shown in ig. (2), because the load is the same for both the pushing and retracting sides, use Graph (2), which is the retracting side with a smaller force. Determine the load factor of 1, and the operating pressure of 75 PSI. Then, seek the point at which it intersects with the load weight of 9 lbs, and this will result in a bore size of 1.5 inches. Example 3: To pull a load with a 1 lbs weight vertically upward as shown in ig. (3), use Graph (2) to determine the load factor of.5 and the operating pressure of 75 PSI. Then, seek the point at which it intersects with the load weight of 1 lbs, and this will result in a bore size of 2. inches. ront matter 2

5 Model Selection Step 2 Take the impact at the stroke end into consideration. ith umper ithout umper CM Graph (3) llowable inetic Energy with umper 1. Graph (4) llowable inetic Energy without umper CM2 1. CM2 CM15 CM15 CM125 CM125 CM16 CM16 CM88 CM88 1. CM75 1. CM75 CM56 CM56 oad (lb) CM44 oad (lb) CM Max. speed (in/s) Max. speed (in/s) ront matter 3

6 Model Selection Step 3 The aspects indicated below may need to be taken into consideration, depending on how the cylinder is operated. The maximum stroke at which the cylinder can be operated under a lateral load. The region that does not exceed the bold solid line represents the allowable lateral load in relation to the cylinder of a given stroke length. In the graph, the range of the broken line shows that the long stroke limit has been exceeded. In this region, as a rule, operate the cylinder by providing a guide along the direction of movement. Graph (5) Max. llowable ateral oad.44 (7/16"),.56 (9/16"), (3/4"), (7/8"), 1.6 (1-1/16"), 1.25 (1-1/4"), 1.5 (1-1/2"), 2. (2") 1. fr ushing (earing) 1. CM ateral load applied to the rod end fr (lbf) 1. CME CMC CM2 CM15 CM125 CM16 CM88 CM75 CM56.1 CM Cylinder stroke (in) ront matter 4

7 Model Selection Step 3 The aspects indicated below may need to be taken into consideration, depending on how the cylinder is operated. Mounting Type perating pressure Maximum stroke that can be used according to buckling strength CM Mounting Type (PSI) Type 1 Type 2 Type 3 25 (12) , Type 4 25 (12) U T Type 1 Type 2 Type 3 25 (12) (12) (4) 34 (4) (4) (4) 5 (12) (12) (4) (4) 75 (12) (12) (4) , 2 1 (12) (12) (12) (12) (12) (12) (12) (12) (12) Type 1 Type 2 Type 3 25 (12) (12) (4) (4) (4) (4) (4) 5 (12) (12) (4) 34 (4) (4) (4) 75 (12) (12) (4) (4) 1, 2 1 (12) (12) (4) (4) 125 (12) (12) (4) (12) (12) (4) (12) (12) (4) (4) 5 (12) (12) (12) (12) (12) (12) The relationship between the cylinder size and the maximum stroke depending on the mounting style. ssuming that the force that is generated by the cylinder itself acts as a buckling force on the piston rod or on the piston rod and the cylinder tube, the table below indicates in inches the maximum stroke that can be used, which was obtained through calculation. Therefore, it is possible to find the maximum stroke that can be used with each cylinder size according to the relationship between the level of the operating pressure and the type of cylinder mounting, regardless of the load factor. Reference: Even under a light load, if the piston rod has been stopped by an external stopper at the extending side of the cylinder, the maximum force generated by the cylinder will act upon the cylinder itself. The data in ( ) are limited by max. stroke length. ote 1) This data is in.5 inch increments (round off). ote 2) or those that exceed maximum stroke that can be manufactured, (4) indicates the maximum stroke that can be manufactured (4) (4) (4) (4) P ront matter 5

8 Model Selection Step 4 btain the cylinder s air consumption and its required air volume. Cylinder s air consumption and its required air volume. In equipment that used a cylinder, air consumption is the volume of air that is consumed in the cylinder, or in the piping between the cylinder and the switching valve, every time the switching valve operates. This is necessary for selecting a compressor and for calculating the running cost. The required air volume is the volume of air that is necessry for operating a specified load at a specified speed, and it is necessary for selecting the.r. equipment or the size of the upstream piping. How to btain the ir Consumption/How to Read Graphs (6), (7) Step 1 Step 2 Step 3 ote)in selecting a compressor, the temperature drop, leakage, and consumption by the intermediary equipment must be taken into consideration. Thus, select one with a generous capacity, with a discharge that exceeds the total air consumption indicated above. (Reference: t a minimum, select one with 1.4 times the volume; select one with a higher volume as needed.) Example: hen 1 air cylinders with a 1.25 inch bore size and a 3 inch stroke are used at a pressure of 5 PSI, what is the air consumption of their 5 cycles per minute? ( 2 inch tube with a.179 inch bore is used for piping between the cylinders and the switching valve.) 1.perating pressure 5 PSI Cylinder stroke 3 inch ore size 1.25 inch ir consumption.5 l(r) 2.perating pressure 5 PSI Piping length 2 inch ore.179 inch ir consumption.1 l (R) 3.Total air consumption = (.5 +.1) x 1 x 5 = 3 l/min (R) How to btain the Required ir Volume/How to Read Graph (8) Step 3 y using Graph (6), obtain the air consumption of the air cylinder. Seek the point at which the operating pressure (diagonal line) intersects with the cylinder stroke, and from that point, perpendicularly extend a vertical line upward. rom the point at which it intersects with the bore size (diagonal line) of the cylinder to be used, look sideways (Either to the right or left) to obtain the air consumption that is required by one cycle of the air cylinder. y using Graph (7), obtain the air consumption of the tube or steel pipe in the same way as in Step 1. btain the total air consumption per minute as described below. (ir consumption of air cylinder + ir consumption of tube or steel pipe) x umber of cycles per minute x umber of cylinders being used = Total air consumption [Unit: l/min (R)] y using Graph (8), obtain the air cylinder s required air volume. Seek the point at which the operating pressure (diagonal line) intersects with the cylinder stroke, and from that point, perpendicularly extend a vertical line upward. rom the point at which it intersects with the bore size (diagonal line) of the cylinder to be used, look sideways (Either to the right or left) to obtain the air consumption that is required by one cycle of the air cylinder. Example:hat is the required air volume for operating a cylinder with a bore size of 1.25 inch, at pressure of 5 PSI, and at a speed of 1 inch/s? How to read: perating pressure 5 PSI Maximum piston speed 5 mm/s ore size 1.25 inch Then, a required air volume 3 l/min (R) can be obtained. Graph (6) Cylinder s ir Consumption (or one cycle) ir consumption (l (R)) Cylinder stroke (in) perating pressure (PSI) ore size (in) ir consumption (l(r)).1 ront matter 6

9 Model Selection Step 4 btain the cylinder s air consumption and its required air volume. Cylinder s air consumption and its required air volume. In equipment that used a cylinder, air consumption is the volume of air that is consumed in the cylinder, or in the piping between the cylinder and the switching valve, every time the switching valve operates. This is necessary for selecting a compressor and for calculating the running cost. The required air volume is the volume of air that is necessry for operating a specified load at a specified speed, and it is necessary for selecting the.r. equipment or the size of the upstream piping. Graph (7) ir Consumption of Tube or Steel Pipe (or one cycle) Graph (8) Required ir Volume of Cylinder and Piping ir consumption (l (R)) Tube I.D. (in) ir consumption (l (R)).1.1 Required air volume (l /min (R)) ore size (in) Required air volume (l /min (R)) Piping length perating pressure (PSI) Max. piston speed (inch/s) perating pressure (PSI) The piping length is the length of the steel pipe or tube that connects the cylinder with the switching valve (solenoid valve, etc.) or the dimensions (bore size and.d.) of the steel tubing, refer to SMC est Pneumatics 24 Vol. 6 catalog. ront matter 7

10 ir Cylinder: Standard Double cting, Single/Double Rod Series CM How to rder C M M9 uilt-in magnet il D one uilt-in magnet with auto switch Mounting C E R ront nose mount Rear pivot mount Double end mount lock mount ote 2, 1, 11) Double rod ote 3, 1) ore size /16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 2" ote 3, 4) Standard stroke Inches ote 5) Stroke Hundredths of an inch (i.e. 6 =.6") il ithout C ote 6) umper bumper umper il J ote 1, 11) Rod boot one ylon tarpaulin Heat resistant tarpaulin ote 1) ption hen ordering multiple options, refer to options compatibility page to ensure options availability. il one X6 High temperature ote 1, 11) X7 ow temperature ote 1, 11) X9 ow speed ote 1, 11) XC4 Heavy duty wiper ote 1) XC6 Stainless steel rod ote 9) X13US Rotated ports ote 7, 1) X114US Rear clevis mount without pin and with rear clevis bronze bushing. ote 1, 11) X142US ong stroke ote 1,11) X155US Rear pivot mount (C) without clevis pin ote 1, 11) X163US Heavy duty spring ote 12) X169US Dimensional interchange to other manufacturer s magnetic reed switch cylinders ote 1, 8, 1) X62 ir tank ote 1) X65 Spring assist ote 12) uto switch umber of auto switches il 2 pcs. S 1 pc. n n pcs. il ithout auto switch or applicable auto switch models, refer to the table on page 2. ote 1) ø3/4", ø1-1/16", ø1-1/2" and ø2" only. ote 2) ot offered in ø7/8", ø1-1/4", or with rod boot. ote 3) Double acting only. ote 4) ot available as standard with C, R mount, with rod boot. ote 5) See specifications for standard and maximum stroke lengths. ote 6) umper is offered at no additional cost on ø7/8" and ø1-1/4". They are options on the other bore sizes. The C after the bore size must be included in either case. umper affects cylinder overall length of some models. Refer to the dimensional data. ote 7) vailable only with or C mounting. ot available on 2" bore. ote 8) ot available with ø7/8" bore, or with C, R mount, or non-rotating rod (). ote 9) Stainless steel rod standard on ø7/16", ø9/16", ø3/4" and ø7/8". ote 1) Exclude ø7/16" and ø9/16". ote 11) Exclude ø2". ote 12) ø3/4", ø1-1/16" and ø1-1/2" only. 1

11 Series CM uto Switch Specifications pplicable uto Switches Type Solid state switch Reed switch Special function Diagnostic indication (2-color indication) ater resistant (2-color indication) ith diagnostic output (2-color indication) Diagnostic indication (2-color indication) Electrical entry Grommet Connector Grommet Grommet Connector Grommet iring (utput) 3-wire (P) 3-wire (PP) 2-wire 3-wire (P) 24 V 5 V, 12 V 3-wire (PP) 2-wire 4-wire (P) ead wire length symbols:.5 m il (Example) M9 1 m M (Example) M9M 3 m (Example) M9 5 m Z (Example) M9Z oad voltage one (Example) H7C or details about auto switches with pre-wired connector, refer to est Pneumatics catalog. D-9, M9, M9 are shipped together. (nly switch mounting bracket is assembled at the time of shipment.) D-M9M and M9VM which lead wire length is 1 m are available from July, 28. Indicator light Yes Yes one Yes one Yes one Yes 3-wire (P equivalent) 2-wire 24 V DC 5 V, 12 V 12 V 12 V 5 V, 12 V 5 V C 1 V 1 V or less 1 V, 2 V 12 V 2 V or less 24 V or less uto switch model M9 M9P M9 H7C M9 M9P M9 H7 H C73C C8C 59 ead wire length (m).5 (il) 1 (M) 3 () Solid state switches marked with are produced upon receipt of order. D-54, 64, and 59 cannot be mounted for bore size 44 and (Z) one () Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC 2

12 Series CM ption Compatibility ption Compatibility (1) Description ote CMStandard CDM CM CM- J CM- C X6 X7 X9 XC6 CM CDM CM CM- J CM- C X6 X7 X9 XC6 C E R Standard uto switch capable Double rod ylon rod boot eoprene rod boot umper Heat resistant Cold resistant ow speed Stainless steel rod ront nose mount Rear pivot mount Double end mount lock mount 5 1, 5 1, 5 2 1, 5 1, 5 1, , 5 Combination available to order S vailable with special request ot available ote 1) Exclude ø2". ote 2) umper no additional charge on ø7/8" and ø1-1/4". ote 3) Stainless steel rod standard on ø7/16", ø9/16", ø3/4" and ø7/8". Use XC6 option to get stainless steel rod nut. ote 4) lock mount not available in ø7/8" and ø1-1/4". ote 5) Exclude ø7/16" and ø9/16". S S S S S S S S S S S S S S S ption Compatibility (2) Double acting, Single rod, o bumper Double acting, Single rod, ith bumper Double acting, Double rod, o bumper Double acting, Double rod, ith bumper ith rod boot Direct double acting, Single rod, o bumper Direct double acting, Single rod, ith bumper Direct single acting, Spring return (S), o bumper Direct single acting, Spring extend (T), o bumper Double acting, Single rod, o bumper X6 Double acting, Single rod, o bumper X7 Double acting, Single rod, o bumper X9 Double acting, Single rod, ith bumper X9 Double acting, Single rod, o bumper XC6 Double acting, Single rod, ith bumper XC6 Double acting, Single rod, o bumper, ith air cushion Standard Standard Standard Standard

13 Series CM Specifications: Double cting, Single/Double Rod Specifications luid Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed umper ubrication Mounting ore size ote) R mount available on ø3/4", ø1-1/16", and ø1-1/2" only. Standard Stroke Mounting ront nose mount () Rear pivot mount (C) Double end mount (E) lock mount (R) ote 3) Double rod () ote 3) 44 (7/16") 56 (9/16") 88 (7/8") 16 (1-1/16") 2 (2") Standard stroke 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4, 5, 6 ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 14 / 5 to 6 C o bumper: 2 to 2 in/sec (5 to 5 mm/sec) umper: 2 to 3 in/sec (5 to 75 mm/sec) ptional (o additional charge on 7/8" and 1-1/4" bore) ot required (Pre-lubricated at factory), C, E, R (see ote) Max. stroke as standard ote 2) ong stroke -X142US ote 3) ote 1) Minimum stroke for mounting auto switches:.6 inch for 2 switches,.4 inch for one switch. ote 2) The production maximum stroke of ø7/16" and ø9/16" are up to 12 inches. ote 3) Exclude ø7/16" and ø9/16" eight (Except on-rotating Rod) ore size 44 (7/16") 56 (9/16") 88 (7/8") 2 (2") ase weight by mounting style C / E R / /.21 /.43 / 1.2 / / / dd l weight per inch stroke, C, E, R / / dd l weight for magnet dd l weight for bumper (lbs) Theoretical utput: Double cting Cylinder (Extend) ore size (in) 44 (7/16") 56 (9/16") 88 (7/8") 2 (2") Rod size (in) perating direction UT I UT I UT I UT I UT I UT I UT I UT I Piston area (in 2 ) perating pressure (PSI) (lbf) 4

14 Series CM Construction: Double cting, Single Rod CM44/56 CM44 shown as example Component Parts o Description Rod cover Head cover Cylinder tube Piston Piston Piston rod 7/16", 9/16" umper Rod seal Piston seal Tube gasket ith bumper Material luminum alloy luminum alloy Stainless steel luminum alloy luminum alloy Stainless steel Urethane R R R ote nodized nodized Chromated Chromated CM75 and above 5 Component Parts o Description Rod cover Head cover Cylinder tube Piston 3/4", 7/8" Piston rod 1-1/16", 1-1/4", 1-1/2", 2" ushing ear ring Retaining ring umper Retaining ring Rod seal Piston seal Piston gasket Material luminum alloy luminum alloy Stainless steel luminum alloy Stainless steel Carbon steel Sintered bronze Phenolic resin Spring steel Urethane Spring steel R R R ith bumper ote nodized nodized Chromated Hard chrome plated

15 Series CM Construction: Double cting, Double Rod Component Parts o Description Rod cover Cylinder tube Piston 3/4", 7/8" Piston rod 1-1/16", 1-1/4", 1-1/2", 2" ushing Retaining ring umper Piston seal Piston gasket Rod seal Material luminum alloy Stainless steel luminum alloy Stainless steel Carbon steel Sintered bronze Spring steel Urethane R R R ote Clear anodized Stainless steel 34 Chromated Hard chrome plated 6

16 Series CM Dimensions: Double cting, Single Rod ront nose mount: C(D)M 44 (7/16") øe MM-DI Y ZC Z+Stroke ZD-U ZD-U øe -DI E MM-DI Y.37 ZC ore size 44 (7/16") 56 (9/16") E E.52 o.1-32 o.1-32 MM E /16-2 7/16-2 Y.72 ZC.5.6 ZD o.1-32 o.1-32 Z o bumper, o magnet Z ith bumper, o magnet Z o bumper, ith magnet Z ith bumper, ith magnet Y Z + Stroke ZC ZD E øe C ømm -U-2 -MUTIG UT 56 (9/16") øe Z+Stroke ZD-U ZD-U øe -U-2 -MUTIG UT -DI E, 88 (7/8"),,,, 2 (2") -Mounting ut (incl. except 2" bore) D-cross lats -U-2 ø Pilot ZD ore size 88 (7/8") 2 (2") MM /4-28 1/4-28 5/ /16-2 7/16-2 1/ D E C E /4-16 3/ / Y ZC ZD 1/8 PT 1/8 PT 1/8 PT 1/8 PT 1/8 PT 1/4 PT Z o bumper Z ith bumper

17 Series CM Dimensions: Double cting, Single Rod Rear pivot mount: C(D)MC 44 (7/16") øe MM-DI Y Z + Stroke + Stroke 2xZD U YC G-DI Pin G øe -U-2 -U-2 ZC -U-2 -DI Z+Stroke +Stroke Y 56 (9/16") 2xZD U.37 øe MM-DI YC G-DI ushing øe -U-2 -U-2 ZC -U-2 -DI ore size 44 (7/16") 56 (9/16") E G G o.1-32 o.1-32 MM /16-2 7/16-2 Y.72 YC.44 ZC ZD.5 o o.1-32 o bumper, o magnet ith bumper, o magnet o bumper, ith magnet ith bumper, ith magnet Z o bumper, o magnet Z ith bumper, o magnet Z o bumper, ith magnet Z ith bumper, ith magnet , 88 (7/8"),,, Z + Stroke ømm -U-2 D-cross lats -U-2 Y ZC ø Pilot + Stroke ZD ZD ZC YC øg øg Pin -U-2 øe G X155US ore size 88 (7/8") (without clevis pin) øg ore size 88 (7/8") MM /4-28 1/4-28 5/ /16-2 7/ D E ote) There are no threads on the CMC 15 rear tang ( dim). 3/4-16 G.375 G /4-16 3/4-16 Y YC Z o bumper Z ith bumper

18 Series CM Dimensions: Double cting, Single Rod Double end mount: C(D)ME 44 (7/16") øe MM-DI Y ZC Z+Stroke +Stroke 2xZD U YC ZC -MUTIG UT G-DI Pin hole øe -U-2 -MUTIG UT -DI -DI 56 (9/16") øe MM-DI Y.37 ZC Z+Stroke +Stroke 2xZD U YC ZC -MUTIG UT G-DI ushing øe -U-2 -MUTIG UT -DI -DI ore size 44 (7/16") (9/16") E G o.1-32 o.1-32 MM /16-2 7/16-2 Y.72, 88 (7/8"),,,, 2 (2") YC.44 ZC ZD.5 o o.1-32 o bumper, ith bumper, o bumper, ith bumper, o magnet o magnet ith magnet ith magnet Z o bumper, o magnet Z ith bumper, o magnet Z o bumper, ith magnet Z ith bumper, ith magnet Y ZC Z + Stroke + Stroke ZD ZD ZC øg Pivot Pin Hole øe ø Pilot ømm -U-2 D-cross lats -Mounting ut (incl. except 2" bore) ø Pilot YC YC -Mounting ut (incl. except 2" bore) CME 15 9 ore size 88 (7/8") 2 (2") ore size 88 (7/8") 2 (2") o bumper Z MM /4-28 1/4-28 5/ /16-2 7/16-2 1/2-2 ith bumper Z D E G /4-16 3/ / Y YC ZC ZD 1/8 PT 1/8 PT 1/8 PT 1/8 PT 1/8 PT 1/4 PT

19 Series CM Dimensions: Double cting, Single Rod lock mount: C(D)MR Z + Stroke E 2-DD tap on ø olt circle X C YE T E ømm U-2 E øe ø Pilot EE PT 2-Drill & C'ore for H caps screw & T UC from bottom EE PT D cross lats ore size MM /4-28 7/16-2 5/ C D.22 DD 1-32 U 1-32 U 1/4-2 UC E E EE 1/8 1/8 1/ E H 1-32 U 1-32 U 1/4-2 UC T 1/4-2 1/4-2 5/16-18 T YE X lock Mount ore size o bumper Z ith bumper ote) ength not affected by addition of magnet. 1

20 Series CM Dimensions: Double cting, Double Rod Z + (2 X Stroke) + Stroke + Stroke YE YE øe ømm 2-ZD 2-ZC 2-ø Pilot 2- U-2 2-D cross lats 2-Y 2-2- Mounting ut (incl. except 2" bore) ore size 88 (7/8") 2 (2") MM /4-28 1/4-28 5/ /16-2 7/16-2 1/ D E /4-16 3/ / Y YE ZC ZD 1/8 PT 1/8 PT 1/8 PT 1/8 PT 1/8 PT 1/4 PT Double cting, Double Rod ore size 88 (7/8") 2 (2") o bumper ith bumper o bumper ith bumper ote) ength not affected by addition of magnet except 16 bore. Z Double cting, Double Rod with Magnet (16 ore) ore size o bumper 3.13 ith bumper 3.25 o bumper 4.38 Z ith bumper

21 ir Cylinder: on-rotating Rod Double cting, Single Rod Series CM How to rder C M M9 uilt-in magnet il D one uilt-in magnet with auto switch ption il X142US one ong stroke on-rotating rod Mounting C E ront nose mount Rear pivot mount Double end mount ore size /4" 7/8" 1-1/16" 1-1/4" 1-1/2" uto switch il ithout auto switch or applicable auto switch models, refer to the table on page 13. umber of auto switches il 2 pcs. S 1 pc. n n pcs. Standard stroke Inches ote 1) Stroke Hundredths of an inch (i.e. 6 =.6") il C umper ithout bumper umper ote 1) See specifications for standard and maximum stroke lengths. 13

22 Series CM uto Switch Specifications pplicable uto Switches Type Solid state switch Reed switch Special function Diagnostic indication (2-color indication) ater resistant (2-color indication) ith diagnostic output (2-color indication) Diagnostic indication (2-color indication) Electrical entry Grommet Connector Grommet Grommet Connector Grommet Indicator light Yes Yes one Yes one Yes one Yes iring (utput) 3-wire (P) 3-wire (PP) 2-wire 3-wire (P) 24 V 5 V, 12 V 3-wire (PP) 2-wire 4-wire (P) 3-wire (P equivalent) 2-wire 24 V oad voltage DC 5 V, 12 V ead wire length symbols:.5 m il (Example) M9 Solid state switches marked with are produced upon receipt of order. 1 m M (Example) M9M D-54, 64, and 59 cannot be mounted for bore size 44 and m (Example) M9 5 m Z (Example) M9Z one (Example) H7C or details about auto switches with pre-wired connector, refer to est Pneumatics catalog. D-9, M9, M9 are shipped together. (nly switch mounting bracket is assembled at the time of shipment.) D-M9M and M9VM which lead wire length is 1 m are available from July, V 12 V 5 V, 12 V 5 V C 1 V 1 V or less 1 V, 2 V 12 V 2 V or less 24 V or less uto switch model M9 M9P M9 H7C M9 M9P M9 H7 H C73C C8C 59 ead wire length (m).5 (il) 1 (M) 3 () 5 (Z) one () Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC ption Compatibility ption Compatibility (1) Description ote CDM CM CDM CM CM- J CM- C X6 X7 X9 XC6 C E R uto switch capable on-rotating ylon rod boot eoprene rod boot umper Heat resistant Cold resistant ow speed Stainless steel rod ront nose mount Rear pivot mount Double end mount lock mount 1, 7 1, 7 1, 7 2 1, 7 1, 7 1, 7 3, 4 1 1, 5, 6, 7 S S S S S S Combination available to order S vailable with special request ot available ote 1) Exclude ø2". ote 2) umper no additional charge on ø7/8" and ø1-1/4". ote 3) Stainless steel rod standard on ø7/16", ø9/16", ø3/4" and ø7/8". Use XC6 option to get stainless steel rod nut. ote 4) on-rotating rod is stainless steel. Use XC6 option to get stainless steel rod nut. ote 5) lock mount not available in ø7/8" and ø1-1/4". ote 6) lock, uto switch capable, S and T only available as special. ote 7) Exclude ø7/16" and ø9/16". ption Compatibility (2) Double acting, Single rod, o bumper, on-rotating rod Double acting, Single rod, ith bumper, on-rotating rod

23 Series CM Specifications: Double cting, Single Rod on-rotating Rod Specifications ore size luid Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Rod material umper on-rotating accuracy Maximum allowable torque 88 (7/8") ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 14 / 5 to 6 C 2 to 2 in/sec / 5 to 5 mm/sec Stainless steel 33 ptional (o additional charge on 7/8" and 1-1/4" bore) ± 2. ± ft bf (.6 m).9 ft bf (.13 m).12 ft bf (.16 m) Standard Stroke Mounting Standard stroke Max. stroke as standard ong stroke -X142US ront nose mount () Double end mount (E) Rear pivot mount (C) 1/2, 1, 2, 3, 4, 5, 6, 1/2, 1, 2, 3, 4, 5, 6, 7, 8, 1, 12 ote 1) Minimum stroke for mounting auto switches:.6 inch for 2 switches,.4 inch for one switch. ote 2) Spring return up to 18" available as special request Theoretical utput: on-rotating Rod ore size 88 (7/8") Rod diameter perating direction UT I UT I UT I UT I UT I Effective area (sq.inch) perating pressure (PSI) (lbf) eight (lbs) ore size 88 (7/8") ase weight by mounting style C E dd l weight per inch stroke dd l weight for magnet dd l weight for bumper

24 Series CM Dimensions: Double cting, Single Rod on-rotating Rod ront nose mount Z1 + STRE.9 øe D C -U-2 1/8 PT E 1/8 PT MUTIG UT (ICUDED) Z2 + STRE.9 øg PI G D -U-2 1/8 PT YC -U-2 -U-2 + STRE Z3 + STRE.9 C-Pilot.87 øg PIVT PI HE (no.pin hole for 1.5" ore) D -DI Pilot Rear pivot mount øe Double end mount Pilot -DI Pilot Y -U-2 1/8 PT YC -MUTIG UT (ICUDED) + STRE MUTIG UT (ICUDED) ore size 88 (7/8") MM /4-28 1/4-28 5/ /8-24 3/ C D E /4-16 (C) 3/4-16(E) G G.375 G (C) C E /4-16 7/ Y YC.78.78(C) on-rotating Rod (/C/E) Mount ore size 88 (7/8") o bumper (C) ith bumper (C) Z1 o bumper ith bumper ote) ength not affected by addition of magnet. o bumper (C) Z2 ith bumper (C) Z3 o bumper ith bumper

25 ir Cylinder: Standard Single cting, Spring Return/Extend Series CM How to rder C M M9 il D Mounting C E uilt-in magnet one uilt-in magnet with auto switch ront nose mount Rear pivot mount Double end mount ore size /4" 7/8" 1-1/16" 1-1/4" 1-1/2" ption hen ordering multiple options, refer to options compatibility page to ensure options availability. il one Stainless steel rod ote 3) XC6 X65 X163US Spring assist ote 4) Heavy duty spring ote 4) umber of auto switches il 2 pcs. S 1 pc. n n pcs. Standard stroke Inches ote 1) Stroke Hundredths of an inch (i.e. 6 =.6") il ithout C ote 2) umper bumper umper ction S T uto switch il ithout auto switch or applicable auto switch models, refer to the table on page 18. Spring return Spring extend ote 1) See specifications for standard and maximum stroke lengths. ote 2) umper is offered at no additional cost on ø7/8" and ø1-1/4". They are options on the other bore sizes. The C after the bore size must be included in either case. umper affects cylinder overall length of some models. Refer to the dimensional data. ote 3) Stainless steel rod standard on ø3/4" and ø7/8". ote 4) ø3/4", ø1-1/16" and ø1-1/2" only. 17

26 Series CM uto Switch Specifications pplicable uto Switches Type Solid state switch Reed switch Special function Diagnostic indication (2-color indication) ater resistant (2-color indication) ith diagnostic output (2-color indication) Diagnostic indication (2-color indication) Electrical entry Grommet Connector Grommet Grommet Connector Grommet Indicator light Yes Yes one Yes one Yes one Yes iring (utput) 3-wire (P) 3-wire (PP) 2-wire 3-wire (P) 24 V 5 V, 12 V 3-wire (PP) 2-wire 4-wire (P) 3-wire (P equivalent) 2-wire 24 V oad voltage DC 5 V, 12 V ead wire length symbols:.5 m il (Example) M9 Solid state switches marked with are produced upon receipt of order. 1 m M (Example) M9M D-54, 64, and 59 cannot be mounted for bore size 44 and m (Example) M9 5 m Z (Example) M9Z one (Example) H7C or details about auto switches with pre-wired connector, refer to est Pneumatics catalog. D-9, M9, M9 are shipped together. (nly switch mounting bracket is assembled at the time of shipment.) D-M9M and M9VM which lead wire length is 1 m are available from July, V 12 V 5 V, 12 V 5 V C 1 V 1 V or less 1 V, 2 V 12 V 2 V or less 24 V or less uto switch model M9 M9P M9 H7C M9 M9P M9 H7 H C73C C8C 59 ead wire length (m).5 (il) 1 (M) 3 () 5 (Z) one () Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC ption Compatibility ption Compatibility (1) Description ote CDM S T CDM S T C X6 X7 X9 XC6 C E R uto switch capable Spring return Spring extend umper Heat resistant Cold resistant ow speed Stainless steel rod ront nose mount Rear pivot mount Double end mount lock mount ption Compatibility (2) 1, 6 1, 6 1, 6 1, 2, 6 1, 6 1, 6 1, 6 1, 3, 6 1, 6 1, 6 1, 6 1, 5, 6 S S S S Single acting, Spring return (S), o bumper Single acting, Spring return (S), ith bumper Single acting, Spring extend (T), o bumper Single acting, Spring extend (T), ith bumper Direct single acting, Spring return (S), o bumper Direct single acting, Spring extend (T), o bumper Single acting, Spring extend (T), o bumper XC6 Single acting, Spring extend (T), ith bumper XC6 S S S S S Combination available to order S vailable with special request ot available ote 1) Exclude ø2". ote 2) umper no additional charge on ø7/8" and ø1-1/4". ote 3) Stainless steel rod standard on ø7/16", ø9/16", ø3/4" and ø7/8". Use XC6 option to get stainless steel rod nut. ote 4) lock mount not available in ø7/8" and ø1-1/4". ote 5) lock, uto switch capable, S and T only available as special. ote 6) Exclude ø7/16" and ø9/16"

27 Series CM Specifications: Single cting, Spring Return / Spring Extend Specifications ore size 88 (7/8") luid Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed umper ubrication Mounting ir 25 PSI / 1.7 MPa 25 PSI /.18 MPa 4 to 14 / 5 to 6 C 2 to 2 in/sec / 5 to 5 mm/s ptional (o additional charge on 7/8" and 1-1/4" bore) ot required (Pre-lubricated at factory), C, E, R ote) R mount available on 3/4", 1-1/16", and 1-1/2" bore only. Standard Stroke Mounting Standard stroke Max. stroke ront nose mount () Rear pivot mount (C) Double end mount (E) lock mount (R) ote) Up to 18" available as special request. 1/2, 1, 1-1/2, 2, 3, 4 6 Theoretical utput: Spring Return (S) with Standard Rod ore size 88 (7/8") Rod diameter perating direction UT I UT I UT I UT I UT I Effective area (sq.inch) ote1) orce on extension (UT) is shown as the theoretical force of a double acting cylinder on extension less the compressed force of the return spring. ote 2) orce on retraction (I) is the resting force of spring when fully retracted Theoretical utput: Spring Extend (T) with Standard Rod ore size 88 (7/8") Rod diameter perating direction UT I UT I UT I UT I UT I Effective area (sq.inch) perating pressure (PSI) ote1) orce on retraction (I) is shown as the theoretical force of a double acting cylinder on retraction less the compressed force of the extend spring. ote 2) orce on extension (UT) is the resting force of spring when fully extended perating pressure (PSI) (lbf) (lbf) 19

28 Series CM Specifications: Single cting, Spring Return / Spring Extend Spring orce: Spring Return (S) and Spring Extend (T) Type Cylinders ore size 88 (7/8") Resting lbf () 3 (13.3) 3 (13.3) 3 (13.3) 7 (31.2) 7 (31.2) Compressed lbf () 6 (26.8) 5.45(24.4) 6 (26.8) 12.4 (55.6) 12.4 (55.6) (lbs) eight: Single cting, Spring Return except on-rotating Rod ore size 88 (7/8") ase weight by mounting style C E st inch of stroke dd l weight per inch stroke R, C, E, C, E, R.224 /.43 / dd l weight for magnet dd l weight for bumper (lbs) eight: Single cting, Spring Extend except on-rotating Rod ore size 88 (7/8") ase weight by mounting style C E st inch of stroke dd l weight per inch stroke R, C, E, C, E, R.21 /.43 / dd l weight for magnet dd l weight for bumper (lbs) 2

29 Series CM Construction: Single cting, Spring Return ith bumper Component Parts o Description Rod cover Head cover Cylinder tube Piston 3/4", 7/8" Piston rod 1-1/16", 1-1/4", 1-1/2" ushing umper Piston seal Piston gasket Spring Spring guide Material luminum alloy luminum alloy Stainless steel luminum alloy Stainless steel Carbon steel Sintered ronze Urethane R R Music wire luminum alloy ote Clear anodized Clear anodized Stainless steel 34 Chromated Hard chrome plated Chromated Chromated 21

30 Series CM Construction: Single cting, Spring Extend ith bumper Component Parts o Description Rod cover Head cover Cylinder tube Piston 3/4", 7/8" Piston rod 1-1/16", 1-1/4", 1-1/2" ushing Retaining ring umper Retaining ring Piston seal Piston gasket Rod seal Spring Spring guide Material luminum alloy luminum alloy Stainless steel luminum alloy Stainless steel Carbon steel Sintered ronze Spring steel Urethane Spring steel R R R Music wire luminum alloy ote Clear anodized Clear anodized Stainless steel 34 Chromated Hard chrome plated Chromated Chromated 22

31 Series CM Dimensions: Single cting, Spring Return ront nose mount / Spring return CM_-_S Z1 + ZC Per 1" of Stroke.9 E øe C ømm -U-2 D-cross lats -Mounting ut (included) ø Pilot 1/8 PT Double end mount / Spring return CME_-_S Rear pivot mount / Spring return CMC_-_S ømm Y ZC Z + Stroke + Stroke ZD ZD ZC øg Pivot Pin Hole øe ømm Y ZC Z + Stroke + Stroke ZD ZD ZC øg øg Pin øe G ø Pilot ore size 88 (7/8") -Mounting ut (incl. except 2" bore) D-cross lats -U-2 MM /4-28 1/4-28 5/ /16-2 7/16-2 ø Pilot YC -Mounting ut (incl. except 2" bore) D E /4-16 3/4-16 G G.375 G 1. ote 1) dimension for CME15 not applicable. There are no flats on the E type 15 bore rear tang. ote 2) dimension for CMC 15 is not applicable. There are no threads on the C type 15 bore rear tang. YC CME 15 ø Pilot -U-2 D-cross lats -U C E YC -U-2 1/2-2 3/4-16 3/ YC ZC Single cting, Spring Return (/C/E) Mount without Magnet ore size 88 (7/8") o bumper ith bumper o bumper ote) dimension for CME15 not applicable. Z1 ith bumper o bumper Z2 ith bumper X155US (without clevis pin) ore size 88 (7/8") øg Single cting, Spring Return (/C) Mount with Magnet ore size 88 (7/8") o bumper ith bumper o bumper Z1 ith bumper o bumper Z2 ith bumper Single cting, Spring Return (E) Mount with Magnet ore size 88 (7/8") o bumper ith bumper o bumper Z2 ith bumper

32 Series CM Dimensions: Single cting, Spring Extend ront nose mount / Spring extend CM_-_T Z1 + ZC Per 1" of Stroke + Stroke.9 YD ømm øe Double end mount / Spring extend CME_-_T Z2 + ZC Per 1" of Stroke + ZC Per 1" of Stroke + Stroke.9 ømm YD -U-2 D-cross lats -Mounting ut øg Pivot Pin Hole.9 øe ø Pilot 1/8 PT CM 15 Rear pivot mount / Spring extend CMC_-_T Z2 + ZC Per 1" of Stroke + ZC Per 1" of Stroke + Stroke YD.9 ømm 1.25 øg Pin øe G -U-2 D-cross lats 2--Mounting ut (included) ore size 88 (7/8") 2-ø Pilot MM /4-28 1/4-28 5/ /16-2 7/16-2 1/8 PT D E /4-16 G G.375 G ote 1) dimension for CME15 not applicable. There are no flats on the E type 15 bore rear tang. ote 2) dimension for CMC 15 is not applicable. There are no threads on the C type 15 bore rear tang..91 CME 15 -U-2 D-cross lats -U-2 ø Pilot /8 PT -U /4-16 3/4-16 YD ZC Single cting, Spring Extend (/C/E) Mount without Magnet ore size 88 (7/8") o bumper ith bumper o bumper ote) dimension for CME15 not applicable. Z1 ith bumper o bumper Z2 ith bumper X155US (without clevis pin) ore size 88 (7/8") øg Single cting, Spring Extend (/C) Mount with Magnet ore size 88 (7/8") o bumper ith bumper o bumper Z1 ith bumper o bumper Z2 ith bumper Single cting, Spring Extend (E) Mount with Magnet ore size 88 (7/8") o bumper ith bumper o bumper ote) dimension for CME15 not applicable. Z2 ith bumper

33 ir Cylinder: on-rotating Rod Single cting, Spring Return Series CM How to rder C M M9 uilt-in magnet il D one uilt-in magnet with auto switch on-rotating rod ption hen ordering multiple options, refer to options compatibility page to ensure options availability. il one X163US Heavy duty spring Mounting C E ront nose mount Rear pivot mount Double end mount ore size /4" 7/8" 1-1/16" 1-1/4" 1-1/2" umber of auto switches il 2 pcs. S 1 pc. n n pcs. Standard stroke Inches ote 2) Stroke Hundredths of an inch (i.e. 6 =.6") il ithout C ote 3) umper bumper umper ction S Spring return uto switch il ithout auto switch or applicable auto switch models, refer to the table on page 28. ote 1) ot available with double rod (), block mount (R), rod boot. ote 2) See specifications for standard and maximum stroke lengths. ote 3) umper is offered at no additional cost on ø7/8" and ø1-1/4". They are options on the other bore sizes. The C after the bore size must be included in either case. umper affects cylinder overall length of some models. Refer to the dimensional data. 25

34 Series CM uto Switch Specifications pplicable uto Switches Type Solid state switch Reed switch Special function Diagnostic indication (2-color indication) ater resistant (2-color indication) ith diagnostic output (2-color indication) Diagnostic indication (2-color indication) Electrical entry Grommet Connector Grommet Grommet Connector Grommet Indicator light Yes Yes one Yes one Yes one Yes iring (utput) 3-wire (P) 3-wire (PP) 2-wire 3-wire (P) 24 V 5 V, 12 V 3-wire (PP) 2-wire 4-wire (P) 3-wire (P equivalent) 2-wire 24 V oad voltage DC 5 V, 12 V ead wire length symbols:.5 m il (Example) M9 Solid state switches marked with are produced upon receipt of order. 1 m M (Example) M9M D-54, 64, and 59 cannot be mounted for bore size 44 and m (Example) M9 5 m Z (Example) M9Z one (Example) H7C or details about auto switches with pre-wired connector, refer to est Pneumatics catalog. D-9, M9, M9 are shipped together. (nly switch mounting bracket is assembled at the time of shipment.) D-M9M and M9VM which lead wire length is 1 m are available from July, V 12 V 5 V, 12 V 5 V C 1 V 1 V or less 1 V, 2 V 12 V 2 V or less 24 V or less uto switch model M9 M9P M9 H7C M9 M9P M9 H7 H C73C C8C 59 ead wire length (m).5 (il) 1 (M) 3 () 5 (Z) one () Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC ption Compatibility ption Compatibility (1) Description ote CM-S CM-T C CM-S CM-T C C E Spring return Spring extend umper ront nose mount Rear pivot mount Double end mount 1, 3 1, 3 1, 2, 3 1, 3 1, 3 1, 3 Combination available to order S vailable with special request ot available ote 1) Exclude ø2". ote 2) umper no additional charge on ø7/8" and ø1-1/4". ote 3) Exclude ø7/16" and ø9/16". ption Compatibility (2) Single acting, Spring return (S), on-rotating rod, o bumper Single acting, Spring return (S), on-rotating rod, ith bumper

35 Series CM Specifications: Single cting, Spring Return on-rotating Rod Specifications ore size luid Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Rod material umper on-rotating accuracy Maximum allowable torque 88 (7/8") ir 25 PSI / 1.7 MPa 25 PSI /.18 MPa 4 to 14 / 5 to 6 C 2 to 2 in/sec / 5 to 5 mm/s Stainless steel 33 ptional (o additional charge on 7/8" and 1-1/4" bore) ± 2. ± ft bf (.6 m).9 ft bf (.13 m).12 ft bf (.16 m) Standard Stroke Mounting Standard stroke Max. stroke ront nose mount () Double end mount (E) Rear pivot mount (C) 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4, 5, 6 ote 1) Minimum stroke for mounting auto switches:.6 inch for 2 switches,.4 inch for one switch. ote 2) Spring return up to 18" available as special request. Theoretical utput ore size 88 (7/8") Rod diameter perating direction UT I UT I UT I UT I UT I 6 6 Effective area (sq.inch) ote1) orce on extension (UT) is shown as the theoretical force of a double acting non-rotating rod cylinder on extension less the compressed force of the return spring. ote 2) orce on retraction (I) is the resting force of spring when fully retracted perating pressure (PSI) (lbf) eight ore size 88 (7/8") ase weight by mounting style C st Inch of stroke dd l weight per inch stroke E, C, E, C, E dd l weight for magnet dd l weight for bumper (lbs) 27