Easy Ft Sren-Based Alarm system (EF-BX) Installaton Programmng Operatng Keep ths manual safe for reference and future mantenance Introducton Contents Thank you for choosng the Yale Wreless Alarm System. Ths smple to nstall system has been desgned wth the user n mnd. All the components are self contaned and no connectons are needed between the unts. There s no need to damage the home decor, lft carpets or run cables. You can nstall up to 20 devces n ths system. As well as extra door/wndow contacts, PIRs and smoke detectors, you can add keyfob remote controls and keypads for added control convenence. There s no need to wre nto the mans supply or seek the servces of a qualfed electrcan. All components are powered by battery (all batteres ncluded). Batteres wll operate for 2 years or more before they need changng. Regular testng and battery changes (when notfed by the system) wll ensure relablty and peace of mnd. Each part of the system s tamper protected. Any unauthorsed tamperng wth the system wll result n an alarm. Ths feature can be turned off by the user when a battery change s requred. The system has a fxed 20 second entry/ext tme when use wth a Keypad. Ths feature allows you tme to leave the home when armng the system. Upon enterng, the feature allows tme to dsarm the system wthout causng an alarm. Please note there are no countdown when usng a Keyfob to arm or dsarm. When the sren s trggered, t wll sounds for 10 mnutes. Contents 1 Locaton plannng 2 2 Unpackng the system 3 3 Programmng the system 5 4 Mountng alarm devces 6 5 Usng the system 8 Addng accessores 10 Changng the batteres 11 Specfcatons 13 Trouble shootng 14 Recommended Installaton Sequence We recommend you follow the easy start sequence, headngs numbered 1-5. Dsplay extreme cauton when usng ladders or steps, please follow manufacturer nstructons. Be careful when usng hand and power tools and follow the manufacturers gudelnes when usng them. Take care that the correct tools are used. Wear goggles or protectve clothng where requred. The external Sren s extremely loud, please ensure you replace the cover and retreat to a safe dstance before testng. Specal Notes on Compatblty: Ths alarm system s NOT compatble wth SmartHome Alarm, HSA6000 seres and HSA3000 seres accessores. Please note the prefx EF- on the front of the part number to ndcate compatblty. Informaton and llustratons are subject to change wthn ths document. Yale reserves the rght to alter the specfcaton and product desgn at anytme wthout notce. Yale s a regstered trademark. 2012 ASSA ABLOY. All rghts reserved.
Yale Yale 1 2 3 4 5 6 7 8 9 0 Yale Locaton plannng 1Work out the best places to locate the devces for maxmum protecton. Havng chosen the locatons do not mount at ths stage. Operatng range All devces must be wthn 30 metres of the sren unt and must not be mounted on or near large metal objects. Avod obvous sources of electrcal nterference such as frdges and mcrowave ovens. Tamper swtches When mountng devces ensure that any tamper swtches close fully. On uneven surfaces t may be necessary to place packng behnd the swtch for relable operaton. Sren Choose a poston on an external wall where the sren would be most promnent. Mount as hgh as possble, out of easy reach. (Round shaped sren shown) Help button accessory The help button provdes extra protecton for you and your famly. When help s needed the button can actvate your alarm mmedately - even when the system s dsarmed. Mount on flat wall surface Desgned for ndoor use only Out of reach of chldren Hdden from vew whle easly accessble. Smoke detector Mount n the mddle of the celng at the top of a starwell, or on the centre of hallway celngs where smoke would most lkely be detected. Do not mount n corners or above cookng applances and heaters. Install addtonal detectors f there are closed doors preventng smoke from reachng detectors. Door/Wndow contacts Use one door/wndow contact on a door that s used as the man pont of entry and ext, usually your front door. The other door/wndow contact can be used to protect another entry pont such as a rear door. Mount as hgh as possble. Do not am a PIR at ths door or wndow. R Yale Keyfob remote control accessory Can be used outsde the premses and kept on your keyrng. PIR movement detectors Mount n a poston such that an ntruder would normally move across a PIRs feld of vew. Heght should be between 1.9 and 2 metres above floor level. Locaton n a corner wll ensure wder room coverage. Do not mount a PIR where ts feld of vew wll be obstructed e.g. by curtans, ornaments etc. Do not pont drectly at sources of heat e.g. fres or bolers, and do not poston drectly above radators. Avod mountng a PIR drectly facng a wndow. Do not pont a PIR at a door protected by a door/wndow contact. Keypad remote control The keypad should be sted next to the man pont of entry/ ext so that the system can be dsarmed/armed wthn 20 seconds of enterng/leavng the premses. Ensure that the keypad s not vsble from the outsde of the premses. Mount at chest heght for ease of use. Desgned for ndoor use only. Extend the system Extend the system n the future to ncrease your securty or as your needs change. For example, add extra PIR detectors n bedrooms and extra door/wndow contacts (20 devces n total, ncludng keypad). 2
Unpack all the parts on a table top The easest way to get to know the system and get t up and runnng quckly s to get all the 2devces and accessores programmed on a table top before locatng and mountng them. Yale Status LED Learn/Test Button Cover screw Sren 1 Remove the cover by unscrewng the sngle screw located on the ld. 2 Ensure the dp swtches poston are as shown n the dagram. If the swtches are n the wrong poston, please change accordngly. NORMAL PIR movement detectors 1 Pull out the plastc pull tab on the back of the PIR. Ths wll actvate the batteres. (A red lght can be seen flashng through the lens. Ths wll last for 30 seconds ndcatng the component s ntaton. ) DO NOT SWITCH THE POWER SWITCH TO ON POSITION AT THIS STAGE. Dp Swtches DSW 1: Sren Reset DSW 2: Jammng detecton DSW 3: Not n use DSW 4: Sren as Master/Slave (On poston only) Sensor Magnet Yale LED Learn/Test button Gap no more than 10mm / Yale 1 2 3 4 5 6 7 8 9 0 Panc button A Panc button B LED Learn button= Press 8 and 9 together Dsarm HomeArm (Button not n use) Door/wndow contacts 1 Pull out the plastc pull tab found on the sde of the man unt. Ths wll actvate the battery. Keypad remote control 1 Pull out the plastc battery saver tab at the back of the remote keypad. Ths wll actvate the batteres. 3
Keyfob remote control accessory alne efly tng ove) 1 Open the battery compartment usng a con by turnng the cover n the drecton of the bg Keyfob remote control accessory arrow so the cover small arrow s next to round dot. Slde off the battery cover, nsert the 223A/MN21 Insert CR2032 battery battery as shown, and replace and replace cover. battery cover. Swtch to on. On/Off swtch / Smoke detector accessory 1 Remove the cover and nsert three AA batteres. per tch Smoke detector accessory 2 The Smoke detector wll now enter nto selfcalbraton mode for 15-20 mnutes (Do not touch Remove durng the ths cover tme). and It nsert wll resume the four normal AAA batteres operaton as after shown. ths perod. Learn/Test Button LED ntact Yale r as Learn/Test button als Learn/Test button Help button accessory Help button accessory Remove the cover by loosenng the fxng Remove screw and the nsert cover by the loosenng 12V battery the (suppled) fxng screw as and shown. nsert Please the CR2032 ensure battery you observe (suppled) battery as shown polarty. (1). Please observe battery polarty. 1 4 Panc/Learn button 7
3 Programmng the Sren-based system (wthout control panel) The sren s the heart of the system. All components must be recognsed by the sren. 1 WARNING The sren s very loud, be prepared! Take care not to actvate the sren tamper swtch unnecessarly. Swtch the sren s power swtch to ON (The LEDs wll now flash wth one short beep.) 2 SETTING Enable/dsable Jammng & nterference detecton: Set Dp swtch 2 for nterference detecton. Swtch On to enable and Off to dsable (recommended default). Once powered, the sren wll enter learn mode for 3 hours. All tamper protectons are dsabled wthn ths tme perod. Please ensure that ALL devces are ftted before ths mode expres. The system s pre-learnt n the factory and the system should recognsed all the tems (wthn ths kt) as default. Ths unt s equpped wth the latest type of rado recever usng FM rado technology. If the system s armed any crmnal attempt to nterfere detector transmssons wll trgger an alarm. If the alarm s frequently trggered by nterference there may be hgh levels of unusual rado sgnals n your area. Some knds of electronc equpment can generate ths knd of rado nterference. In the unlkely event of you experencng problems wth nterference, t s recommended that you swtch nterference detecton off. If the tems are not recognsed, deleted by accdent or purchased accessores, please press learnt/acton buttons on the accessores (when the power swtch s frst turned on and under learn mode) to learn each one nto the system. Do not press the sren learn button. See Chapter 2 for learn button locaton. The sren wll beep each tme t receves a learnt sgnal. 3 The system s now ready for wall mountng. 5
4 Before Mountng alarm devces mountng the keypad and sren ensure that the sren tamper s dsabled. Mountng the sren Ensure the tamper swtch s fully depressed when the sren s mounted. If there s a gap, pack wth a sutable spacng materal. Sprng compressed frmly aganst wall Round Sren Base Wall Mountng the Keypad: 1 Knock out the fxng holes. Drll holes nto the wall usng the fxng holes as a template. 2 Ft wall plugs nto the wall and fx back cover wth the screws provded. Fx front of the keypad onto the back plate. Sprng Gude 1 Usng the large screws and wall plugs provded, mount on the desred wall through the 4 mountng holes. If there s a gap between the wall and the tamper swtch mechansm pack wth a sutable spacng materal. Battery Saver tab Wall Fxng knockouts x2 2 Fx the sren cover wth the securng screw. Mountng other devces Fnd a locaton where the devce s to be mounted, see secton Locaton Plannng for suggestons. Before proceedng to mount the devces physcally, t s useful to check that t s not out of rado range by dong a smple range test. Please ensure the system tamper s dsabled. Mountng the PIR 1 Open the PIR by va the bottom screw. Knock out the relevant holes at the base. The center two knockout holes are for flat wall mountng whle the 4 sde holes are for corner mountng. Keypad: Hold the keypad n the desred locaton and press the arm button. (The sren wll beep as confrmaton.) Help button: Hold the devce n the desred locaton and press the emergency button for 2 seconds. (The sren should respond wth a sngle beep.) All other devces: Hold the devce n the desred locaton and press the learn/test button. (The sren should respond wth a sngle beep.) When you are satsfed that the devces work n your chosen locatons, proceed wth the nstallaton as descrbed n the next page. If the sren does not respond, the locaton may be out of range, try alternatve locatons untl relable rado contact s obtaned. Battery tab Wall fxng knockouts x2 Corner fxng knockouts x4 2 Drll holes nto the wall usng the knockout holes on the base as a template. Secure the base wth the screws provded. 3 Ft the PIR back together and tghten bottom screw. 6
Mountng the door/wndow contact -Mountng usng screws and wall plugs Frame 1 Loosen the bottom screw and open the door/ wndow contact. Knockouts Sensor Door/Wndow 2 Knock out the holes on the base as shown. Sensor Yale Magnet Gap no more than 10mm 3 Drll holes nto the mountng surface usng the holes n the knockouts on the base as template. 4 Ft wall plugs (f requred) and secure wth the screws provded. 1 Fnd a locaton where the door/wndow contact s to be mounted. It should be mounted between the door/wndow frame and the door/wndow as shown at the top of the openng. The magnet s to go on the door/wndow whle the sensor s to be placed on the frame. Wndows can be protected n a smlar way to doors. Make sure the tamper swtch sprng s fully depressed. The gap between the magnet and sensor should be approxmately 10mm when closed (dependng upon the actual envronment). Smple test to see whether the magnet s n range of the sensor: hold the magnet and sensor n place and then pull them apart. If the sensor LED lghts up t mples the two tems are wthn range. -Mountng usng adhesve pads 1 Clean the mountng surface wth a sutable degreaser agent. 2 Remove the protectve flm from one sde of the adhesve pad and apply to the back of the sensor and magnet 3 Remove the remanng protectve flm and frmly press nto place. 4 Test sensor by pressng the test button and openng and closng the door/wndow. The LED should lght when the door/wndow s opened. Installaton s complete. 5 Ft sensor back together and tghten screw. 6 Test sensor by pressng the test button and openng and closng the door/wndow. The LED should lght when the door/wndow s opened. Installaton s complete. Mountng the Help button 1 Break through the knockouts (where the plastc s thnner). 2 Usng the holes as a template, drll holes n the surface and nsert wall plugs f fxng nto plaster or brck. Screw the rear case to the wall. 3 Replace the cover and tghten the screw. Mountng the Smoke Detector 1 The base has two mountng slots. Usng the slots as a template, drll holes and nsert the wall plugs f fxng to plaster. Screw the rear case to the celng usng the screws provded. 2 Replace the cover. The tamper swtch wll automatcally reactvate after 3 hours (after ntal Sren power swtch On). Alternatvely you can enable the tamper swtch manually by dsarmng usng your keypad (Dsarm & pncode: default 0000). 7
Usng the system Arm and dsarm the system and practce usng t. Trgger the alarm by armng the system and openng protected doors/wndows and walkng past PIRs. Now s the tme to set your pn 5code and show the rest of the famly how smple t s to use. 8 Armng the system Keypad/Keyfob: Press arm (The sren wll beep/flash once. No audble countdown.) Dsarmng the system Keypad: Press dsarm followed by your pncode. Keyfob: Press dsarm. (The sren wll beep twce and flash.) The PIRs have a bult-n sleep tmer to save battery power. If there s no movement n front of the PIRs for 1 mnute, the PIRs wll become ready to sgnal and movement wll now be reported. The PIRs wll sleep for 1 mnute after reportng. Any movement detected n sleep tme wll not be reported and wll extend the sleep perod by a further 1 mnute. Keypad wll arm the system wth a 20 seconds ext perod. All detectors wll be gnored (except for the tamper swtches). The system can be armed when nsde the protected area of your premses. Keyfob wll arm the system nstantly wthout a 20 second ext delay. Any detector actvated afterwards wll trgger an nstant alarm. The system should be armed when outsde the protected area of your premses. Keypad: If the system has been armed wth a keypad there wll be a 20 second entry perod started when the frst detector s actvated (usually a wndow/door contact on the man pont of entry). Durng ths entry perod all detectors wll be gnored. If the system s not dsarmed before the entry perod expres, the alarm wll be actvated. The system does not have an audble countdown durng the entry perod, however the sren wll beep once when the frst detector s trggered. Keyfob: If the system has been armed wth a keyfob there wll be no 20 second entry perod and any detector actvaton wll gve an nstant alarm. The system should be dsarmed from outsde the protected area of your premses. Stoppng the Sren Keypad: Press dsarm followed by your pncode. Keyfob: Press dsarm. (The sren wll be slenced and then beep twce and flash.) Changng your keypad PIN code 1 Enter settng mode: Press the Panc button A, followed by enterng the current pncode (factory default code s 0000). (The LED wll now flash contnuously.) 2 Press panc button B. 3 Enter new 4-dgt pncode. 4 Press Arm button to confrm. 5 Ext settng mode: Press dsarm twce to qut the changng code process. Or wat for 5 mnutes for the keypad to qut test mode automatcally. (The LED wll now stop flashng.) Tamper alarm warnng If any devce tamper swtches are dsturbed a tamper alarm wll be actvated wth the sren soundng and the strobe flashng. The alarm can be slenced as descrbed n Stoppng the Sren. If the PIN code doesn t change, repeat the above procedure quckly wthout gaps. If there s a persstent sren tamper fault then a seres of 5 pps and flashes wll be gven when the system s armed, then the sren should be checked for any mountng problems and f the sren ld s secure. Use packng materal for uneven wall surface. Prevous alarm warnng Should there be an alarm that was trggered and expred (whle the user was away), the sren wll sound and flash for 3 seconds after dsarmng (user returnng home). * Warnng: should ths happen the ntruder could stll be n the premses. My PIN code: (wrte your pncode here so you don t forget t)
Usng the help button Actvate: Press and hold panc button for 3 seconds, the LED wll lght brefly and the sren wll be actvated. Slence: Press and hold panc button for 10 seconds, the LED wll lght brefly and the sren wll be slenced. Panc alarm usng keypad Actvate: Press and hold Panc button A & Panc button B together. Slence: Press dsarm follows by pncode. Panc alarm usng keyfob Please note that slencng the alarm wth the help button does not dsarm the system. If the alarm s armed pror to actvaton, the system wll re-arm after beng slenced wth the help button. Actvate: Press and hold Panc button. Slence: Press dsarm. Usng the smoke detector The smoke detector wll ndcate a fre by soundng ts bult-n sren, lghtng the LED and actvatng the external sren and strobe. -Smoke detecton When smoke s detected the devce wll actvate for a mnmum of 10 seconds wth a two tone alarm and flashng LED for a local fre alarm. The detector wll also actvate the external sren and strobe. Pressng the test button when n an alarm condton wll slence the alarm for 10 mnutes, t wll automatcally resume smoke detecton agan after ths perod. If the smoke densty s stll over the alarm threshold, then the smoke detector wll reman n an alarm condton and t wll repeat the local fre alarm and actvate the external sren and strobe agan. -Testng Smoke detector testng should be done on a regular monthly bass. Pressng the test button wll make the LED flash, the audble sounder chme and wll send a rado test sgnal to the sren when the button s released. If nothng happens after pressng the test button then change the batteres. -Recalbraton The smoke detector mght need recalbratng after tme to ensure t s workng at ts optmum. Ths s done by pressng and holdng n the test button untl the LED flashes and t beeps after 10 seconds. The detector wll then start ts self-calbraton routne. Keypad Modes: Table 1 Enterng settng mode: Press Panc button A followed by pncode (factory default s 0000). You can now select dfferent functon. (The LED on the keypad wll start flahsng) Functon settng: Press Panc button A, followed by one of the followng number key: 1 Send learnng/testng sgnal (same as 8+9) 2 Dsable Sren tamper 3 Enable Sren tamper 4 Enter learn mode (not sutable for frst tme set-up) 5 Ext learn mode 7 Keypad to work wth control panel based sysem. 8 Keypad to work wth sren based system. Extng settng mode: Press dsarm twce. (The LED wll now stop flashng. If not, press dsarm twce agan) KeyFob Modes: Table 2 Sendng learn sgnal Press any key except the emergency button. Sren tamper (Enable) Press and hold down Arm and emergency for 5 seconds. Sren tamper (Dsable) Press and hold down Arm and Home for 5 seconds. Learn mode (Enter) Press and hold down Home and emergency for 5 seconds. Learn mode (Ext) Press and hold down dsarm for 5 seconds. 9
Addng accessores to an exstng system To provde addtonal protecton you can add extra door/wndow contacts, PIRs, keyfob remote controls, keypad remote controls, help buttons and smoke detectors. These are avalable separately from your local stockst. Addng devces to an already nstalled system The nstalled system wll be controlled by ether a keyfob(s) or a keypad(s). Keypad 1 Enter Settng mode: Press Panc button A followed by the pncode (Indcated by a contnuously flashng LED.) 2 Swtch OFF system tamper: Press Panc button A followed by 2 (The sren wll beep n response.) 3 Enter learn mode: Press Panc button A followed by 4. (The sren wll beep and flash n response.) 4 LEARNING: Press devce learn/test buttons (see Chapter 3) to trgger learnng-n sgnals. (The sren wll beep and flash when each devce s learnt n.) Keyfob 1 Press the Arm and Home buttons together and contnuously for 5 seconds untl the LED stops flashng, to swtch off the tamper whle nstallng the new devce. (The sren wll beep n response.) 2 Press the Home and Emergency buttons together and contnuously for 5 seconds untl the LED stops flashng to enter learn mode. (The sren wll beep and flash n response.) 3 Press devce learn/test buttons (see Chapter 3) to trgger learnng-n sgnals. (The sren wll beep and flash when each devce s learnt n.) 4 When all the devces have been learnt-n press and hold the Dsarm button to qut learn mode. 5 Press the Arm and Emergency buttons together and contnuously for 5 seconds untl the LED stops flashng to rearm tamper protecton. 5 Ext learn mode: When all the devces have been learnt n, press Panc button A and 5 to qut learn mode. 6 Swtch ON system tamper: Press Panc button A and 3 to rearm tamper protecton. 7 Ext Settng mode: Press Dsarm twce to ext. (The keypad LED wll now stop flashng.) 10
Changng the batteres Always use alkalne batteres or the correct type of con cells as replacements because any other battery can cause problems wth the operaton of the system. Typcal lfe of batteres s two years. Ensure the correct steps are taken when changng batteres n tamper protected devces. Sren The sren wll produce a seres of pps and flashes when armng and dsarmng the system when the batteres start gettng low. After the warnng the batteres wll have about enough energy for 1 month s normal operaton before exhauston. 1 Swtch off tamper protecton as descrbed n secton 5, table 1 & 2. The batteres are changed as follows: 2 Remove the sren ld and swtch off the sren power. 3 Unscrew the four screws on the battery compartment ld and remove. 4 Remove the four batteres and replace them wth four fresh alkalne D cells. 5 Swtch on sren power and check that the sren beeps and flashes. Note After the batteres have been changed and system powered on, the tamper wll become nactve for 3 hours to allow fttng. 6 Replace battery compartment ld and screws and reattach sren ld. Tamper protecton would automatcally enabled when the 3 hours perod expred. Dsarmng under tamper condton causes the LED to flash sequentally for 2 cycles nstead of 1 cycle under normal condton. PIR When the battery s low the LED wll flash when any movement s detected. The batteres are changed as follows: 1 Swtch off tamper protecton as descrbed n secton 5, table 1 & 2. 2 Loosen the case screw and remove PIR sensor from base to reveal three AAA batteres. 3 Press the learn button to dran resdue power. 4 Insert new alkalne batteres observng correct polarty. 5 Reft sensor on base and tghten bottom case screw. Swtch tamper protecton back on. PIR case tamper condtons are also ndcated by a flashng LED, check the tamper before changng the batteres. Door/wndow sensor When the battery s low the LED wll lghts up when the door/wndow s opened or when tamper s trggered. The battery s changed as follows: 1 Swtch off tamper protecton as descrbed n secton 5, table 1 & 2. 2 Loosen the case screw and remove door/wndow sensor from base to reveal battery. 3 Usng a screwdrver gently lever out the old battery. 4 Insert new CR2032 con cell wth the + sde uppermost. 5 Press battery nto holder frmly wth fnger and thumb untl a clck s heard. 6 Reft sensor on base and tghten bottom case screw. Swtch tamper protecton back on. Door/wndow sensor case tamper condtons are also ndcated by a flashng LED, check the tamper before changng the battery. Keyfob When the battery s low the LED wll glow dmly when any key s pressed. The battery s changed as follows: 1 Usng a con turn the battery cover antclockwse to the unlocked poston and remove cover and battery. 2 Insert new CR2032 con cell wth the + sde uppermost. 3 Replace battery cover. 4 Press any key and check that the LED lghts. If the LED lghts the new battery nstallaton s successful. Keypad Note: Dsable sren tamper before proceedng (Page 9, table 1) When the battery s low the LED wll flash when any key s pressed. The battery s changed as follows: 1 Unscrew the two keypad case screws and remove keypad back to reveal battery. Usng a screwdrver gently lever out the old battery. 2 Insert new CR2032 con cell wth the + sde uppermost. 3 Slde battery nto holder. Please note the + contact pn must stay above the battery. 4 Press a number key and check that the LED lghts. If the LED lghts the new battery nstallaton s successful, screw keypad back on and the battery change s complete. Smoke Detector The LED wll flash and the sounder wll beep every 30 seconds to sgnal low battery. Change the batteres as soon as possble wth fresh AA alkalne replacements. Help Button Remove the cover by loosenng the fxng screw and nsert a new CR2032 battery. 11
ASSA ABLOY Ltd. School Street, Wllenhall West Mdlands England, WV13 3PW ASSA ABLOY Ltd. School Street Wllenhall West Mdlands England WV13 3PW Model: Model: EF-KIT1 HSA3400 HSA6010 HSA3400 EF-KIT2 HSA3020 HSA6020 EF-KIT3 HSA3020 HSA3060 HSA6021 EF-PC HSA3060 HSA6050 EF-DC HSA3010 EF-PIR HSA3010 HSA6060 HSA3050 EF-PETPIR HSA3050 HSA6080 HSA3045 EF-KF HSA3045 HSA6090 EF-KP HSA3080 HSA6091 EF-BX HSA3080 HSA3030 EF-SD HSA3045 HSA3030 EF-PB HSA3070 HSA3070 EF-PANEL EN 300 220-1 / V2.3.1 (2010) EN 300 220-2 / V2.3.1 (2010) EN 301 489-1 / V1.8.1 (2008) EN 301 489-3 / V 1.4.1 (2002) EN 60 950-1 / 2006 + A11 : 2009 + A1: 2010 + A12:2011 John Ward Drector Date: 16/11/06 03/09/12 On behalf of ASSA ABLOY Ltd. 12 17 17
Specfcatons All devces Envronmental condtons -10 C to 40 C, relatve humdty 70% non-condensng for all unts except the external sren. Sren: -20 C to 50 C, relatve humdty 95% non-condensng Rado operatonal range 30m n a typcal domestc nstallaton, range can vary dependng on buldng constructon, devce postons and RF envronment Housngs ABS/polycarbonate Sren Sren output 104dBA sound pressure @ 1m mnmum Rado 868MHz FM Power supply 6V, 4 x D alkalne cells. 2.5 years typcal servce lfe Passve nfra red (PIR) Detector Alarm processng Mcroprocessor controlled dual edge sequental pulse count wth pulse length dscrmnaton Rado 868MHz FM Power supply 4.5V, 3 x AAA alkalne cells. 2 years typcal domestc servce lfe wthout supervson. Movement detecton range 12m, 110 Door/wndow contact Rado 868MHz FM Power supply 3V, CR2032 lthum con cell. 2 years typcal domestc servce lfe wthout supervson. Smoke detector Rado 868MHz FM Power supply 4.5V, 3 x AA alkalne cells. 3 years typcal domestc servce lfe Tested to EN54 Keyfob remote control Rado 868MHz FM Power supply 3V, CR2032 lthum con cell. 3 years typcal domestc servce lfe Keypad remote control Rado 868MHz FM Power supply3v, CR2032 lthum con cell. 3 years typcal domestc servce lfe Help button Rado 868MHz FM Power supply 3V, CR2032 lthum con cell. 3 years typcal domestc servce lfe 13
Troubleshootng For onlne assstance, please vst: www.yale.co.uk 14 Sren Sren does not respond to keypad Keypad low battery or bad connecton. Check battery connectons and polarty, f OK replace battery. Sren batteres are completely exhausted. Check sren batteres by removng sren cover, f there s no tamper alarm when removed, replace batteres wth new alkalne equvalents. Keypad not learnt-n. If sren produces a tamper alarm when the cover s removed, and keypad s OK, learn-n the keypad. Sren could be out of rado range. Sren produces a 3 second alarm when dsarmed There has been a prevous alarm and there mght be an ntruder stll n the premses. Sren produces a seres of pps when armed or dsarmed The sren has low batteres. Check that the sren produces a seres of pps when armng and dsarmng, ndcatng low batteres. Change batteres wth new alkalne replacements. The sren tamper swtch has been dsturbed. Check that the sren produces a seres of pps only when armng, ndcatng a tamper condton. Check that the sren cover s frmly secured and the tamper swtch plunger s n contact wth the wall. If not use sutable packng materal to fll gap. Sren produces an nterrupted tone when soundng an alarm The sren has low batteres. Change batteres wth new alkalne replacements. Keypad The keypad LED wll not lght when the arm key s pressed Battery s completely exhausted. Change battery wth CR2032 con cell replacement. The keypad LED wll not work after battery changes Battery s completely exhausted. Change battery wth CR2032 con cell replacement. Battery been nserted ncorrectly and the + battery contact pn had been pressed to the sde. Check the battery compartment and ensure the + battery pn stays above the battery. The sren wll not respond to the dsarm user code Ensure that the keypad mode s correct by enterng test mode and pressng button A then 8. Forgotten user PIN code See Keypad reset procedure on the next page. PIR PIR does not respond to movement The PIRs have a bult-n sleep tmer to save battery power. If there s no movement n front of the PIRs for 1 mnute, the PIRs wll become ready to sgnal and movement wll now be reported. The PIRs wll sleep for 1 mnute after reportng. Any movement detected n sleep tme wll not be reported and wll extend the sleep perod by a further 1 mnute. To test, arm system and vacate protected room for at least 1.5 mnutes before testng. PIR s slow to respond Ths s normal, the PIR has sophstcated false alarm flterng that wll flter out random fluctuatons and responds to genune movement across feld of vew, t s less senstve walkng drectly towards t. PIR gves false alarms Check pets have no access to protected area. Check that PIR s not ponted at sources of heat or movng objects, e.g. flutterng curtans. Check that PIR s not mounted above convector heaters or pontng drectly at wndows. PIR LED flashes Batteres are low or the tamper swtch s dsturbed. Check that the tamper swtch sprng s makng contact wth base. If the tamper swtch s OK, change batteres wth new alkalne replacements. PIR does not respond to movement after test/ learn button has be pressed Batteres are completely exhausted. Change batteres wth new alkalne replacements, LED wll flash for 30 seconds whle components ntalse. Door contact Door contact LED lghts up Batteres are low or the tamper swtch s dsturbed. Check that the tamper swtch sprng s makng contact wth the mountng surface. If the tamper swtch s OK, change batteres wth new alkalne replacements. Door contact does not respond to door
openng after test/learn button has been pressed Batteres are completely exhausted. Change batteres wth new alkalne replacements The magnet s too far away from the door contact. Check that the gap between door contact and magnet s not greater than 10mm. Sren reset procedure Swtch the power swtch to Off poston. Press the learn buttons a few tmes to dran any resdual power. Swtch DpSwtch 1 to On poston Swtch the power swtch to On poston. Wat 5 seconds. Sren LED wll flash 1 cycle. Swtch DpSwtch 1 to Off poston The sren s now reset and all learnt devces are cleared from memory. See chapter 3 for ntal setup. Please be remnded that all devces wll need to be learnt n at ths pont. One by one, press the learnt button on devce to learnt n. Keypad reset procedure The keypad s tamper protected. Please ensure the sren tamper s dsabled before you open the keypad cover. See Page 9, table 1 for sren tamper dsable procedure. Open cover and remove battery. Rensert wth the number 3 key pressed (takng care 3 s held down). The keypad wll go back to the 0000 keypad code. The keypad wll now have to be re-learnt nto the Sren, see chapter 3. 15
All devces Passve nfra red (PIR) detector Power supply 3 x AAA alkalne cells. 3 years typcal domestc servce lfe All devces Passve nfra red (PIR) detector EMC Alarm processng Mcroprocessor controlled dual edge sequental pulse Tested to ETS 300 683 EMC Alarm processng Help button Mcroprocessor 2 Year Guarantee count wth pulse length dscrmnaton Rado Components tested to EN controlled dual edge sequental pulse Tested Rado to 433.92MHz ETS 300 683 AM transmtter EMC Tested to EN 300 220-1 and ETS 300 220-1 Statement count wth pulse length dscrmnaton Rado Power Components supply 4.5V, tested 3 x AA to alkalne EN cells. Rado 433.92MHz 300 683 AM transmtter 300 220-1 3 years typcal domestc servce lfe, 1- Envronmental condtons Power supply Envronmental 4.5V, 3 x AA condtons alkalne cells. -10 C to mnute sleep tmer 3 years 40 C, typcal relatve domestc humdty servce 70% lfe, noncondensng sleep tmer 1- Ths product -10 C s to guaranteed 40 C, relatve for consumers humdty aganst Envronmental faulty workmanshp, Movement condtons detecton range 15m, 110 mnute materals 70% and non-condensng functon for a perod for all of unts 2 years from the -10 C date of to purchase 40 C, relatve humdty Movement Rado detecton operatonal range 15m, range 110 30m n a provdng except the the full external nstallaton sren. and mantenance Sren: -20 Cnstructons 70% non-condensng Door/wndow are followed. for contact all unts typcal domestc nstallaton. Can vary Please to 50 C, keep your relatve proof humdty of purchase 95% safe, noncondensng to 50 C, relatve humdty 95% non- ths must dependng buldng constructon and except be submtted the external when sren. Sren: -20 C Door/wndow contact makng a clam under ths guarantee. Rado Mcroprocessor controlled RF envronment 433.92MHz AM transmtter Rado Mcroprocessor controlled Rado Mcroprocessor controlled Please note that t s a condton of ths guarantee condensng that Power your supply Yale 3V, 2 x AAA alkalne cells. 3 433.92MHz AM transmtter Rado operatonal range 433.92MHz AM transmtter product: years typcal domestc servce lfe Power supply 12V 23A/MN21 alkalne Power supply 3V, 2 x AAA alkalne cells. 3 30m n a typcal domestc Rado operatonal range mnature lghter battery. 3 years years typcal domestc servce lfe Has nstallaton, been correctly range nstalled can vary and dependng mantaned n accordance 30m typcal domestc servce lfe Smoke n a wth typcal the detector domestc Yale on buldng nstallaton constructon, and mantenance devce nstructons nstallaton, provded to you range at can vary dependng Smoke detector the tme of purchase. postons and RF envronment on buldng Radoconstructon, Mcroprocessor devce controlled Has not been modfed or damaged n any way. 433.92MHz AM transmtter postons and RF envronment Rado Mcroprocessor controlled Has Housngs not been ABS/polycarbonate subjected to unauthorzed repars. Power supply 6V, 4 x AAA alkalne cells. 3 433.92MHz AM transmtter Housngsyears ABS/polycarbonate typcal domestc servce lfe Power supply 6V, 4 x AAA alkalne cells. 3 Yale are responsble under ths guarantee for reparng the product or Sren years typcal domestc servce lfe replacng the product as we deem necessary. If there s Sren Keyfob fault wth remote the control product, Sren output please 104dBA contact sound Customer pressure Servces @ on 01902 364647, who Keyfob remote control wll gve 1m mnmum you the name of an expert and confrm what you Sren output Rado need 104dBA Mcroprocessor to do sound pressure controlled @ to make Radoa 433.92MHz clam under AM ths guarantee. super heterodyne 1m mnmum 433.92MHz AM transmtter Rado Mcroprocessor controlled recever wth jammng detecton Rado 433.92MHz Power supply AM 12V, super 23A/MN21 heterodyne alkalne 433.92MHz AM transmtter Please Power do supply not carry 6V, out 4 x any D alkalne repars wthout cells. 3our authorty recever or mnature wth by usng jammng "lghter" an detecton battery. 3 years Power supply 12V, 23A/MN21 alkalne unauthorsed years typcal expert. servce Any repars lfe or other works carred Power supply out typcal wthout 6V, domestc 4 our x D alkalne servce cells. lfe 3 mnature "lghter" battery. 3 years authorzaton or by usng an unauthorzed expert years wll not typcal Keypad be covered servce remote lfe control typcal domestc servce lfe under ths guarantee. Keypad remote control Rado Mcroprocessor controlled Ths guarantee s non transferrable and apples to products 433.92MHz purchased AM transmtter Rado Mcroprocessor controlled 433.92MHz AM transmtter n the Unted Kngdom only. Ths guarantee does not apply to normal wear and tear. Ths does not affect your statutory rghts. A full copy of ths guarantee s avalable upon request by wrtng to Yale UK, School Street, Wllenhall, West Mdlands. WV13 3PW or by vstng our webste www.yale.co.uk. Power supply 3 x A years typcal dom Help button EMC Tested to EN 300 683 Envronmental c 40 C, relatve hum condensng Rado operaton typcal domestc dependng on bu RF envronment Rado Mcroproc 433.92MHz AM t Power supply 12 mnature lghter typcal domestc 18 18 0560 NoPb E1 09/12 056 16 WEEE Note: Waste electrcal products and batteres should not be dsposed of wth household waste. Please recycle where facltes exst. Check wth your local authorty or retaler for recyclng advce. THE YALE BRAND, wth ts unparalleled global reach and range of products, reassures more people n more countres than any other consumer lockng soluton. THE ASSA ABLOY GROUP s the world s leadng manufacturer and suppler of lockng solutons, dedcated to satsfyng end-user needs for securty, safety and convenence.