Technical Specifications Series Fischer Connectors S SaintPrex, Switzerland Phone +41 21 800 95 95 Fax +41 21 800 39 24 www.fischerconnectors.com mail@fischerconnectors.ch Multipole Product range covered: S / SC / S / SV / SOV / SS / SSC / WSO / SF / SFE / SFU / SFPE / SFPU / D / DB / DBP / DBPC / DG / DGP DEE / DEU / DBEE / DBEU / DBPE / DBPU / DBPLE / DBPLU / K / KE / KS / KSE / DKBE / WDE Product Benefits Up to a maximum of 27 contacts Unsealed (IP50), waterproof (IP68) or hermetically sealed 3 keyingcodes Reverse contact variants matt silver chrome or nonreflective matt black chrome finish Full range of accessories including bend reliefs and sealing caps available Scoopproof (IEC 60514) Representative image of standard S and D bodies Pages Environmental & Mechanical Data... 2 Material & Surface Treatments... 2 Electrical Data... 2 Configurations... 3 Tooling... 5 Information provided herein is believed to be accurate at time of publishing. Fischer Connectors reserves the right to make modifications on products for continuous improvement without prior notice. Fischer Connectors S / ll rights reserved This document is the proprietary of Fischer Connectors S. ll communications to third parties or the reproduction in any form, even partial, are prohibited without our written consent. Document No. 600.00.457 Rev : 2.1 Date : 06 Jan. 10 Established by : SKE pproved by : DMI Page 1 of 5
Series Multipole Environmental & Mechanical Data Characteristic Product Type Value Sealing Performance Unsealed Connectors (mated) Plugs with (mated) General Purpose Sealed Clamps IP50 IP68: 2 m submersion for 24 hours IP69K (2) IEC 60529 Receptacles U Body Style IP68: 2 m submersion for 24 hours Operating Temperature Range Corrosion Resistance Endurance Vibration Radiation Resistance Receptacles E Body Style Material & Surface Treatments Unsealed Connectors Plugs Using General Purpose Sealed Clamps Receptacles U Body Style Receptacles E Body Style 65 C to +200 C 65 C to +130 C 50 C to +200 C 5 000 mating cycles Unsealed Connectors PEEK: 10 6 Gy (=100M Rads) Sealed Receptacles Viton Orings: 10 5 Gy (=10M Rads) The sealing performance can be affected by the long term quality of the cable. Hermetic: Tested: < 10 8 mbar l/sec. IP69K (2) 50 C to +150 C 10 to 2000 Hz, 1.5 mm or 15 g, sweep cycles per axis, 20 minutes per 10200010 Hz sweep cycle, no discontinuity > 1 us (2) Dust tight, protected against the effects of highpressure liquids. The test requirements for IP69K exist only in DIN 400509, the German version of IEC 60529. With Viton Oring (standard) in receptacle interface: Operating temperature of Viton Oring: 20 C to +200 C. Min mating temperature of 0 C. With EPDM Oring (Low temp) on request in receptacle interface: Operating temperature of EPDM Oring: 50 C to +160 C. Min mating temperature of 20 C. For information only. Not tested by Fischer Connectors. Salt mist, 96 hours, 5% salt solution, 35 C IEC 605611 i+j IEC 60068214Nb IEC 60068211 Test Ka MILSTD202 Method 101 Condition IEC 60559a EI36409 MILSTD202 Method 204 Condition B Metal Parts ISO Material Finish Body Shell Cable Clamps, Nuts and other Inner Parts Brass Cun39Pb3 (solder) Brass Cun39Pb3 Chrome over Nickel Brass Cun39Pb3 Nickel, (crimp) Bronze CuSn4n4Pb4 CW456K STM B 139, UNS C 54400 1 µm Gold over Nickel SEMSQQC320 SEMSQQN290 SEMS2404 MILDTL45204D Type I STM B488 Insulator and Sealing International Symbol Flammability Insulator PEEK UL 94 V0 MILP46183 Interface Orings (Receptacles) Viton EPDM UL 94 V0 ~SEMS7276 Sealant Material (Receptacles) IP68 Hermetic Silicon compound Epoxy compound UL 94 V0 Cable Sealing (Plugs) IP68 TPES Our products are RoHS compliant and conform with the EC Directive 2002/95/EC Electrical Data Characteristic Size Typical Values Resistance over 5 000 Mating Cycles Ø0.5 mm mm mm mm mm Ø2.3 mm 5 mω 5 mω 4 mω IEC 60522a/b Shell Resistance 20 mω IEC 60522f Insulation Resistance > 10 10 Ω IEC 60523a, Method C Shielding Effectiveness > 60 db up to 1GHz IEC 605233 Document No. 600.00.457 Rev : 2.1 Page 2 of 5
Series Multipole Configurations Type Pin Layout Number of Diameter [mm] Wire Size Solder (2) Crimp Current Rating [] IEC 60535b Rated Voltage r.m.s. [V] IEC 606641 Insertion/Extraction Force (typ.) [N] IEC 605713a, MILSTD1344 Unsealed Sealed Max Ø1.86 mm 051 2 1.6 WG13 [1] 20 ~35 WG14 [7/22] 040 3 1.6 Max Ø1.86 mm WG13 [1] WG14 [7/22] Max 1.78 mm Min 1.17 mm WG1418 18 037 4 1.3 WG17 [1] WG18 [16/30] Max 1.18 mm Min 0.58 mm WG1824 Max Ø2.48 mm 2 2.3 WG11 [1] 28 WG [7/20] 087 4 400 2 WG21 [1] 3.0 WG22 [7/30] 053 5 1.3 WG17 [1] 11 WG18 [16/30] 065 6 Max 0.83 mm 6.5 400 WG21 [1] WG22 [7/30] WG2226 054 7 WG21 [1] 6.5 WG22 [7/30] 066 8 Max 0.83 mm 6.2 WG21 [1] WG22 [7/30] WG2226 1 1.3 WG17 [1] WG18 [16/30] 055 9 250 8 WG21 [1] WG22 [7/30] 6.0 Stranding values in brackets. (2) Exceptionally for a given WG, the diameter of some stranded conductor designs could be larger than the hole diameter of the barrel. Trials may be required. Recommended max. operating current per contact at 40 C temperature rise. Recommended operating voltage at sea level. This rated voltage is a general purpose guideline where no other electrical safety standard applies. In case other standards rule a specific use of the connector, then the application specific safety criteria shall be considered first. This must be evaluated in the frame of equipment engineering. In case other calculation methods are preferred, please refer to general catalogue for test voltage data. Values may vary strongly depending on environmental conditions, ageing, finish or type of seal. Document No. 600.00.457 Rev : 2.1 Page 3 of 5
Series Multipole Configurations (cont.) Type Pin Layout Number of Diameter [mm] Wire Size Solder (2) Crimp Current Rating [] IEC 60535b Rated Voltage r.m.s. [V] IEC 606641 Insertion/Extraction Force (typ.) [N] IEC 605713a, MILSTD1344 Unsealed Sealed 056 11 WG21 [1] WG22 [7/30] Max 0.83 mm WG2226 5.8 250 ~30 086 16 0.7 WG21 [1] WG22 [7/30] Max 0.62 mm Min 0.38 mm WG2428 4.0 ~35 ~55 092 19 Max 0.62 mm Min 0.38 mm 0.7 3.5 WG21 [1] ~60 WG22 [7/30] WG2428 Max 0.43 mm 4 27 0.5 Min 0.20 mm 2.0 (6) WG2832 ~60 Stranding values in brackets. (2) Exceptionally for a given WG, the diameter of some stranded conductor designs could be larger than the hole diameter of the barrel. Trials may be required. Recommended max. operating current per contact at 40 C temperature rise. Recommended operating voltage at sea level. This rated voltage is a general purpose guideline where no other electrical safety standard applies. In case other standards rule a specific use of the connector, then the application specific safety criteria shall be considered first. This must be evaluated in the frame of equipment engineering. In case other calculation methods are preferred, please refer to general catalogue for test voltage data. (6) Values may vary strongly depending on environmental conditions, ageing, finish or type of seal. This configuration has different environmental performances than those shown on page 2 due to the use of another sealant material. Please contact us for more information. Document No. 600.00.457 Rev : 2.1 Page 4 of 5
Series Multipole Tooling Gender Size [mm] Part Number Crimp Tool TX00.240 Crimp Positioner TX00.304 TX00.305 TX00.307 TX00.309 TX00.311 TX00.3 TX00.313 TX00.314 Insertion Tool TX00.210 TX00.211 TX00.273 Extraction Tool TX00.200 TX00.205 TX00.2 TX00.201 DoubleEnd Open Spanner Extra Thin 13 TX00.0 TX00.013 14 TX00.014 OpenEnd Spanner Extra Thin 17 19 TX00.017 TX00.019 Nut Driver with THandle and Hex Drive for Decorative Slotted Nut M 15 x 1 M 16 x 1 TK00.000 TK00.002 For detailed crimping instructions, log on to our online technical library at www.fischerconnectors.com/technical Document No. 600.00.457 Rev : 2.1 Page 5 of 5