Series LS 30A to 600 Vac SIP Package DC Control
|
|
|
- Briana Chandler
- 7 years ago
- Views:
Transcription
1 3A to 6 Vac SIP Package Part Number LS24D16C-HS1 LS6D22C-HS1 LS24D27C LS6D3C Description 16A, 24 Vac 22A, 6 Vac 27A, 24 Vac 3A, 6 Vac Part Number Explanation LS 24 D 16 C Series Switch Type 2 Control Range 3 Line Voltage 1 Output Current Amps NOTES 1) Line Voltage (nominal) 24 = 24 Vac; 6 = 6 Vac 2) Switch Type: D = Zero-cross turn-on 3) Control Range: C = 4-14 Vdc FEATURES/BENEFITS Industry standard package Designed for external heat-sink attachment Over-sized thyristor ratings Direct-copper bonding technology.96 (24.5).31 (7.83) MECHANICAL SPECIFICATION Hot surface: 1.48 (37.6) (5.8).5 (12.7) 1.71 (43.6) Ø1.4 (1.16) Top view Hole Ø.6 (1.6) WEIGHT:.53 oz. (15g).3 (7.83).2 (.55).1 (.3) Hot surface:.69 (17.5).16 (4).7 ±.6 (1.7 ±.15).7 (1.7).1 (2.54).25 (6.3).6 x.6 (1.5 x 1.5).3 (7.6) TOLERANCES: ±.7 (±.2mm) Figure 1 - LS relays; (See Figure 12 for LS with HS1) TYPICAL APPLICATION L1 L1 DESCRIPTION These solid-state single inline package (SIP) relays are designed for mounting on printed circuit boards. The Series LS relays facilitate heat sinking by providing an interface surface. The relays are designed with 16A, 25A and 5A thyristors. They can switch loads with high starting currents. The nominal switched currents depend on the size of the heat sink and are limited by the cross section of the tracks of the printed circuit (mainly 25A/3A). The relays use a direct-bonded copper substrate for thermal effi ciency, thermal stress performance and long-life expectancy. APPLICATIONS Motor control Pumps, reversing, integration of relays in terminal boxes Lamp control Infrared drying, traffi c lights, theater lighting APPROVALS All models are UL recognized. UL File Number: E MOV on the PCB Load BLOCK DIAGRAM SSR Or MOV on the PCB 3 + Rc Ic 1 ~ Load Vc SSR N N Figure 2 LS relays 4 Figure 3 LS relays 2 ~ 216 TELEDYNE RELAYS (8) LS Page 1 LS\9214\Q3
2 3A to 6 Vac SIP Package INPUT (CONTROL) SPECIFICATION Min Max Units Control Range 4 14 Vdc Input Current Range madc Must Turn-off Voltage 1 Vdc Input Resistance (Typical) 44 Ohms OUTPUT (LOAD) SPECIFICATION Min Max Unit Operating Range LS Vrms LS Vrms Peak Voltage LS24D16C 6 Vpeak LS6D22C 12 Vpeak Load Current Range LS24D16C.5 16* Arms LS6D22C.5 25* Arms LS24D27C.5 3* Arms LS6D3C.5 3* Arms *Limited by the heat sink Maximum Surge Current Rating () (See Figure 6) LS24D16C 16 LS6D22C 3 LS24D27C 6 LS6D3C 1 Power Dissipation (W) Power Dissipation (W) Full on state Input Current (ma) CONTROL CHARACTERISTIC THERMAL CHARACTERISTICS Full on state Control Voltage (V) Figure 4 LS relays FW1 (~4 C/W) FW1 (~4 C/W) 6 C/W Without heat sink Figure 5a LS24D16C relay FW15 (~3 C/W) C/W FW15 (~3 C/W) On-State Voltage Drop 1.6 V Zero-Cross Window (Typical) ±12 V 5 Without heat sink Figure 5b LS6D22C relays Off-State Leakage Current (6Hz) 1 ma 4 Power Dissipation (W) Full on state FW1 (~4 C/W) 6 C/W FW15 (~3 C/W) Without heat sink Figure 5c LS24D27C, LS6D3C relays LS Page 2 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 216 TELEDYNE RELAYS LS\9214\Q3
3 3A to 6 Vac SIP Package OUTPUT (LOAD) SPECIFICATION (continued) Min Max Unit Turn-On Time (6Hz) 8.3 ms Turn-Off Time (6Hz) 8.3 ms Off-State dv/dt 5 V/μs Operating Frequency 1 44 Hz I 2 t for match fusing (<8.3ms) LS24D16C 128 A 2 S LS6D22C 45 A 2 S LS24D27C 18 A 2 S LS6D3C 5 A 2 S ENVIRONMENTAL SPECIFICATION Min Max Unit Operating Temperature 4 8 C Storage Temperature 4 12 C Input-Output Isolation 4 Vrms Output-Case Isolation 33 Vrms NOTES: 1. MOV across the output recommended for non-resistive loads minimum size: 14mm 2. Maximum current based on size of the heat sink and the ambient temperature. 3. For 8Hz applications, contact factory. 4. For additional/custom options, contact factory. SURGE CURRENTS Repetitive with initial Tj = 7 C Repetitive with initial Tj = 7 C t(s) t (s) Figure 6a L24D16C relay Repetitive with initial Tj = 7 C t (s) Temps 6 s 1 s Long time Tj init = 45 C I (A) 2 15 Figure 6d LS24D27C relays Figure 6c LS6D22C relay Repetitive with initial Tj = 7 C.1 1 t(s) Figure 6e LS6D3C relay TELEDYNE RELAYS (8) LS Page 3 LS\9214\Q3
4 3A to 6 Vac SIP Package MOUNTING EXAMPLES Heat sinks references: FW1: L=1mm about 4 C/W (1SSR) without ventilation (3.6 C/W with 4SSRs ) FW15: L=15mm about 3 C/W (1SSR) without ventilation (2.6 C/W with 6SSRs ) Supports additional heat sink if necessary Clips reference: L ±6 2 (7.9 ±.15) (51).16 (4) to maintain isolation Figure 7a Thermal heat sinks with mounting clips; M3.16 (4) to maintain insulation 1.4 (26.5) clips: L191 Printed circuit board Figure 7b Clips with screws on standard heat sinks; In each case, allow.16 in. (4mm) between the printed circuit board and the heat sink to keep a correct insulation between input to output (.16 in./4mm insulated washer). To maintain a good contact between the SSR and the heat sink, use thermal grease. LS Page 4 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 216 TELEDYNE RELAYS LS\9214\Q3
5 3A to 6 Vac SIP Package MECHANICAL SPECIFICATION L1911 CLIP (3) M4 = = M4.1 = =.31 (7.9) (47.2).1.28 (7).99 (25.2) Length: FW1 = 3.94 (1) FW15 = 5.9 (15) Figure 8 FW1 and FW15 heat sinks; FW1 heat sink with Max Clip System* Rth = 3.6 C/W (4 SSRs) Rth = 4 C/W (1 SSR) FW15 heat sink with Max Clip System* Rth = 2.6 C/W (4 SSRs) Rth = 3 C/W (1 SSR) *The Max Clip System of Aavid Thermalloy, patented worldwide Figure 9a Clip for FW1 and FW15 heat sinks Relay ±.1.7 (1.7).16 (4) Figure 9b Mounting with L1911 clip; L191 CLIP M3 Figure 1a Clips with screws for other heat sinks.16 (4) Relay ±.1.7 (1.7) 1.4 (26.5) Figure 1b Mounting with L191 clip; NOTES inch (4mm) mounting washer must have correct insulation between input to output. 216 TELEDYNE RELAYS (8) LS Page 5 LS\9214\Q3
6 3A to 6 Vac SIP Package LS WITH HS1 HEAT SINK.87 (22).5 (12.7) Tolerances: (43.6).95 (24.2).25 (6.3).7 (1.73) 1.1 (28) 1.4 (35.7).3 (7.5) Ø1.2 (5.8).5 (12.7).31 (7.83) Figure 11 LS with HS1 WEIGHT: 1.6 oz. (3g).4 (1.16) Top view INPUT (CONTROL) SPECIFICATION Min Max Units Control Range LS24D16C-HS Vdc Input Current Range LS24D16C-HS madc Must Turn-Off Voltage All relays 1 Vdc Input Resistance (Typical) LS24D16C-HS1 44 Ohms Hole Ø (2.54) Figure 12 LS relays with HS1; LOAD CURRENT DERATING CURVE Convection cooling Forced air cooling with heat sink temperature 85 C max Figure 13a LS24D16X-HS1 relays LS Page 6 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 216 TELEDYNE RELAYS LS\9214\Q3
Schematic Mechanical Drawing Derating Curve. Input. Output. Product Catalogue
Input 1 Product Catalogue Single Phase SSR (24VAC) 1 ~ 4 Amps : DC Control, : Triac output 42.5 Series : 1 J/K 3 Input (+) & 4 Input (-) 1 & 2 35.6 25.5 57.75 28. 45. A = 3.2 C/W B = 1. C/W C & D =.5 C/W
Solid State Relays Industrial, 1-Phase ZS w. LED Types RS 23, RS 40, RS 48
Solid State Relays Industrial, 1-Phase ZS w. LED Types RS 23, RS 0, RS 8 Zero switching AC Solid State Relay Direct copper bonding (DCB) technology in 25A and 0A types LED indication Clip-on IP 20 protection
650W Single Output Power Supply 15V 24V. 27V 48V Rated Current. 0 ~ 100A 0 ~ 50A 0 ~ 40A 0 ~ 27A 0 ~ 24A 0 ~ 13.6A Rated Power
Features: Universal AC input / Full range Programmable output Voltage (0% ~ 05%) Programmable output Current (% ~ 05%) + / 0.5A auxiliary output Forced current sharing at parallel operation Power OK signal
1000W Single Output Power Supply 15V 24V. Protection type: Total Power limit, Latch-style (Recovery after reset AC power ON or inhibit)
000W Single Output Power Supply AK-000 series Features: Universal AC input / Full range Programmable output Voltage (0% ~ 05%) Programmable output Current (% ~ 05%) + / 0.5A auxiliary output U profile,
AZ420 MINIATURE GENERAL PURPOSE RELAY
MINIATURE GENERAL PURPOSE RELAY FEATURES Rugged construction for high reliability Life expectancy greater than 0 million operations DC coils to 11 V Power consumption as low as 2 mw per pole available
AC/DC Power Modules C B. TML Series, 20 & 40 Watt. Features. 20 Watt Models
TML Series, 0 & 0 Watt Features C B Scheme LVD UL 090- Encapsulated power supplies with increased power density Replaces TML and TML 0 series PCB mount or chassis mount with screw terminals Single, dual
650W Single Output Power Supply
AK-650 series Features : Universal AC input with active PFC Programmable output Voltage ( 0% ~ 05% ) Programmable output Current ( % ~ 05% ) High efficiency up to 9% + / 0.5A auxiliary output Intelligent
UMEC International Corporation
UP1301A SERIES 130 Watt Open Frame Switchers Small Size 3*5*1.2(inches) Universal Input to 264 VAC Low Power Consumption Overvoltage Protection Continuous Short Circuit Protection Over Temperature Protection
Power Supplies 3. SDN-P DIN Rail Series
SDN-P DIN Rail Series The SDN DIN Rail power supplies provide industry leading performance. Sag Immunity, transient suppression and noise tolerant, the SDN series ensures compatibility in demanding applications.
Single Output Switching Power Supply
.. RS- Code: CLP-A Single Output Switching Power Supply SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY EMC (Note 6) OTHERS NOTE DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER RIPPLE
Surface Mount Technology cooling for high volumes applications by: Cesare Capriz Aavid Thermalloy via XXV Aprile 32 Cadriano (BO) ITALY
Surface Mount Technology cooling for high volumes applications by: Cesare Capriz Aavid Thermalloy via XXV Aprile 32 Cadriano (BO) ITALY Abstract: The automotive technology is fast moving in integrating
TEP 200WIR Series, 180 240 Watt
TEP 200WIR Series, 180 240 Watt Features Chassis mount with screw terminal block Including EMI filter to meet EN 55022, class A Ultra wide 4:1 input voltage ranges 8.5 36, 16.5 75, 43 160 VDC EN 50155
HIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT
HIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT SERIES RF00 RF00D RF00DD RF0 RF0D RF0DD RELAY TYPE Repeatable, RF relay Repeatable, RF relay with internal diode for coil transient suppression Repeatable,
S112-XHS. Description. Features. Agency Approvals. Applications. Absolute Maximum Ratings. Schematic Diagram. Ordering Information
Description Features The S112-X is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay. The circuit is composed of one input IR LED with a series limiting resistor
Example of use: Fuse for a solenoid valve. If the fuse is defective, no information is sent to the electronic component.
Overview Switch and button modules The dimensions of the switch and button modules are adapted to the electronic components in the integral housing. The modules are equipped with the universal clip-on
Specifications for EM223 24 VDC 4 In/4 Out and EM223 24 VDC 4 In/4 Relay Out
SIMATIC S7-200 EM223 Digital Combination Modules EM223 2 VDC In/ Out and EM223 2 VDC In/ Relay Out Table 1 Specifications for EM223 2 VDC In/ Out and EM223 2 VDC In/ Relay Out EM223 2VDC In/Out 6ES7 2231BF200XA0
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 A
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 A Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit EMR Electromechanical Relays
Solid-State Relays. Series Included. Solid-State Relays SIR...145 SLR...146 NLF...147. PHS Series PHS...148
Solid-State Relays Included SIR....145 SLR....146 NLF....147 PHS PHS....148 Solid-State Relays 144 www.ssac.com 800-843-8848 fax: 605-348-5685 Solid-State Relay - Isolated SIR1 & SIR2 Designed for industrial
MCR08B, MCR08M. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 0.8 AMPERES RMS 200 thru 600 VOLTS
MCR8B, MCR8M Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors PNPN devices designed for line powered consumer applications such as relay and lamp drivers, small motor controls,
(600 Volts Peak) SEMICONDUCTOR TECHNICAL DATA
SEMICONDUCTOR TECHNICAL DATA Order this document by MOC0/D (00 Volts Peak) The MOC0, MOC02 and MOC0 devices consist of gallium arsenide infrared emitting diodes optically coupled to monolithic silicon
Application Note TMA Series
1W, SIP, Single & Dual Output DC/DC Converters Features SIP Package with Industry Standard Pinout Package Dimension: 19.5 x 10.2 x 6.1 mm (0.77 x 0.4 x 0.24 ) 5V&12V Models 19.5 x 10.2 x 7.1 mm (0.77 x
L293B L293E PUSH-PULL FOUR CHANNEL DRIVERS. OUTPUT CURRENT 1A PER CHANNEL PEAK OUTPUT CURRENT 2A PER CHANNEL (non repetitive) INHIBIT FACILITY
L293B L293E PUSH-PULL FOUR CHANNEL DRIVERS OUTPUT CURRENT 1A PER CHANNEL PEAK OUTPUT CURRENT 2A PER CHANNEL (non repetitive) INHIBIT FACILITY. HIGH NOISE IMMUNITY SEPARATE LOGIC SUPPLY OVERTEMPERATURE
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 - 16 A
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 - 16 A 38 SERIES Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit EMR Electromechanical
Relés e Contatores de Estado Sólido SIRIUS
Relés e Contatores de Estado Sólido SIRIUS Coletânea de dados técnicos ( product data sheet ) Agosto/212 SSR - 3RF21 22,5 mm Ponto Zero SSR - 3RF2 45 mm Ponto Zero SSR - 3RF22 45 mm Ponto Zero Trifásico
34 Series - Slim electromechanical PCB relays 6 A. Features SERIES 34.51
34 Series - Slim electromechanical PCB relays 6 34 SERIES Features 34.51 Ultra-slim 1 Pole - 6 relay Printed circuit mount - direct or via PCB socket 35 mm rail mount - via screw, screwless or push-in
1SMB59xxBT3G Series, SZ1SMB59xxT3G Series. 3 Watt Plastic Surface Mount Zener Voltage Regulators
9xxBTG Series, SZ9xxTG Series Watt Plastic Surface Mount Zener Voltage Regulators This complete new line of W Zener diodes offers the following advantages. Features Zener Voltage Range. V to V ESD Rating
MTE SERIES RLW. World REACTORS USER MANUAL PART NO. INSTR 030 REL. 090930. 2009 MTE Corporation
MTE SERIES RLW World REACTORS USER MANUAL PART NO. INSTR 030 REL. 090930 2009 MTE Corporation IMPORTANT USER INFORMATION NOTICE MTE Series RLW reactors are components designed to improve the reliability
LM78XX Series Voltage Regulators
LM78XX Series Voltage Regulators General Description Connection Diagrams The LM78XX series of three terminal regulators is available with several fixed output voltages making them useful in a wide range
The Effect of Forced Air Cooling on Heat Sink Thermal Ratings
zpero 1 The Effect of Forced Air Cooling on Heat Sink Thermal Ratings By Paul Bachman, Fellow Engineer & Ronnie Haiduk, Applications Engineer, Crydom, Inc. ABSTRACT A heat sink s ability to dissipate thermal
PDS5100H. Product Summary. Features and Benefits. Mechanical Data. Description and Applications. Ordering Information (Note 5) Marking Information
Green 5A HIGH VOLTAGE SCHOTTKY BARRIER RECTIFIER POWERDI 5 Product Summary I F V R V F MAX (V) I R MAX (ma) (V) (A) @ +25 C @ +25 C 1 5..71.35 Description and Applications This Schottky Barrier Rectifier
EPL225 Series. 225 Watts. www.xppower.com. AC-DC Power Supplies. Models & Ratings. Summary
225 Watts 50 W Convection/ 225 W Forced-cooled Ratings 2 by 4 Footprint Low.26 Profile 2 V Fan Output High Efficiency, up to 95% ITE & Medical pprovals High Power Density Less than 0.5 W No Load Input
1 Form A Solid State Relay
Form A Solid State Relay VOAT, VOAABTR FEATURES 9 S S DC S' 3 S' High speed SSR - t on /t off < 8 μs Maximum R ON. Isolation test voltage 3 V RMS Load voltage V Load current A DC configuration DIP- package
4 A CAPACITY, THE VARIETY OF CONTACT ARRANGEMENTS FEATURES
4 A CAPACITY, THE VARIETY OF CONTACT ARRANEMENTS S RELAYS FEATURES 28. 1.12 12..472 1.4.49 The variety of contact arrangements 2 Form A 2 Form B, 3 Form A 1 Form B, 4 Form A Latching types available High
Figure 1 - Crydom 3RHP Three-phase Hybrid Solid State Contactor. Crydom Inc.
Crydom RHP Series 3 Phase Hybrid Solid State Contactor By Paul Bachman Fellow Engineer, Crydom, Inc. ABSTRACT Solid State Relays and Contactors (SSRs) have been available in one form or the other for over
Current valve. for AC 24 V pulse/pause control of electrical loads up to 30 kw
4 937 DESIO Current valve for AC 24 V pulse/pause control of electrical loads up to 30 kw SEA45.1 Use The current valve is used for the control of electric heating elements in heating, ventilation and
Silvertel. Ag5200. 1 Features. 2 Description. Power-over-Ethernet Plus Module. IEEE802.3at and IEEE802.3af compliant. Maximum 30W output power
Silvertel V1.1 November 2012 Datasheet Pb 1 Features IEEE802.3at and IEEE802.3af compliant Maximum 30W output power Dual In-Line (DIL) package size 50.6mm (L) x 30mm (W) Overload, short-circuit and thermal
MT..KB SERIES 55 A 90 A 110 A THREE PHASE CONTROLLED BRIDGE. Power Modules. Features. Description. Major Ratings and Characteristics
MT..KB SERIES THREE PHASE CONTROLLED BRIDGE Power Modules Features Package fully compatible with the industry standard INT-A-pak power modules series High thermal conductivity package, electrically insulated
NUD4011. Low Current LED Driver
NUD0 Low LED Driver This device is designed to replace discrete solutions for driving LEDs in AC/DC high voltage applications (up to 00 V). An external resistor allows the circuit designer to set the drive
(250 Volts Peak) SEMICONDUCTOR TECHNICAL DATA
SEMICONDUCTOR TECHNICAL DATA Order this document by MOC00/D (0 Volts Peak) The MOC00 Series consists of gallium arsenide infrared emitting diodes, optically coupled to silicon bilateral switch and are
Solid-State Relays (SSRs) vs Electromechanical Relays (EMRs)
Oct 2010 Solid-State Relays (SSRs) vs Electromechanical Relays (EMRs) A study on worldwide relays market found the market size of solid state relays to be between $200M and $600M, which represent 17% of
AS2815. 1.5A Low Dropout Voltage Regulator Adjustable & Fixed Output, Fast Response
1.5A Low Dropout oltage Regulator Adjustable & Fixed Output, Fast Response FEATURES Adjustable Output Down To 1.2 Fixed Output oltages 1.5, 2.5, 3.3, 5.0 Output Current of 1.5A Low Dropout oltage 1.1 Typ.
Pluggable interface relays CR-P Pcb relays
2CDC 293 034 F0004 1 2 4 3 Features 9 different supply s: DC versions: 12 V, 24 V, 48 V, 110 V AC versions: 24 V, 48 V, 110 V, 120 V, 230 V Output contacts: 1 c/o (16 A) or 2 c/o (8 A) Cadmium-free contact
Solid State Relays for Heaters
New Product Solid State Relays for Heaters Single-phase G3PE Compact, Slim-profile SSRs with Heat Sinks. Models with No Zero Cross for a Wide Range of Applications. RoHS compliant. Models also available
AC-DC Converter Application Guidelines
AC-DC Converter Application Guidelines 1. Foreword The following guidelines should be carefully read prior to converter use. Improper use may result in the risk of electric shock, damaging the converter,
Bulletin 150 Smart Motor Controllers SMC-3 Smart Motor Controller
Overview/Modes of Operation Bulletin 150 Smart Motor Controller The SMC-3 is a compact, simple to use, solid-state motor controller designed to operate 3-phase motors. It features a built-in overload relay
(250 Volts Peak) SEMICONDUCTOR TECHNICAL DATA
SEMICONDUCTOR TECHNICAL DATA Order this document by MOC0/D (20 Volts Peak) The MOC0, MOC02 and MOC0 devices consist of gallium arsenide infrared emitting diodes optically coupled to a monolithic silicon
Safety technique. Emergency stop module BO 5988 safemaster
Safety technique Emergency stop module BO 5988 safemaster 0221562 Function diagram Pushbutton on Mains or emergencystop () K1 According to EC Directive for machines 98/37/EG According to IEC/E 60204-1
8ETH06 8ETH06S 8ETH06-1 8ETH06FP
Bulletin PD-0746 rev. D 03/03 8ETH06 8ETH06S 8ETH06-8ETH06FP Hyperfast Rectifier Features Hyperfast Recovery Time Low Forward Voltage Drop Low Leakage Current 75 C Operating unction Temperature UL E78996
PHASED OUT. LED light engine / OLED LED compact. Umodule SLE G4 6mm R SNC, SLE G4 10mm R SNC umodule SLE ESSENCE
w LED light engine / OLED Product description For general lighting application Typ. luminous flux category: 3/6/8/1,2 lm High efficacy up to 133 lm/w for the LED module at tp = 25 C Small LES (light emitting
Advanced Monolithic Systems
Advanced Monolithic Systems FEATURES Three Terminal Adjustable or Fixed oltages* 1.5, 1.8, 2.5, 2.85, 3.3 and 5. Output Current of 1A Operates Down to 1 Dropout Line Regulation:.2% Max. Load Regulation:.4%
O WA-120U series IP67. 120W Single Output Switching Power Supply. Features. Aplications
Features UniversalACinput/Fulrange Built-inactivePFCfunction Higheficiencyupto91% Protections:Shortcircuit/Overcurent/ Overvoltage/Overtemperature Fanlesdesign,colingbyfreairconvection Colingbyfreairconvection
Your Advantages For safety application up to PL e / Cat. 4 e.g. SIL 3 Manual or automatic start 0225592. * see variants. Applications.
Safety Technique SAFEMASTER Emergency Stop Module BG 5924, IP 5924 Your Advantages For safety application up to PL e / Cat. 4 e.g. SIL 3 Manual or automatic start 0225592 BG 5924 IP 5924 Product Description
STPS5L60. Power Schottky rectifier. Description. Features
Power Schottky rectifier Datasheet - production data Description Power Schottky rectifier suited for switch mode power supplies and high frequency inverters. This device is intended for use in low voltage
Capacitance Cap. Tol. Suffix construction. Rated voltage
Metallized Polypropylene Film Capacitors Type:ECWFE Plastic Film Capacitors Non-inductive construction using metalized Polypropylene film with flame retardant plastic case. Features Small size Excellent
BTA40, BTA41 and BTB41 Series
BTA4, BTA41 and BTB41 Series STANDARD 4A TRIACS Table 1: Main Features Symbol Value Unit I T(RMS) 4 A V DRM /V RRM 6 and 8 V I T (Q1 ) 5 ma DESCRIPTION Available in high power packages, the BTA/ BTB4-41
HIGH REPEATABILITY SPDT, BROADBAND 12 GHZ MAGNETIC-LATCHING RF RELAY
HIGH REPEATABILITY SPDT, BROADBAND 12 GHZ MAGNETIC-LATCHING RF RELAY SERIES RF121 RELAY TYPE RF Magnetic-Latching, SPDT, Through-hole Relay DESCRIPTION The ultraminiature RF121 relay is built on Teledyne
KIA7805AF/API~KIA7824AF/API SEMICONDUCTOR TECHNICAL DATA THREE TERMINAL POSITIVE VOLTAGE REGULATORS 5V, 6V, 7V, 8V, 9V, 10V, 12V, 15V, 18V, 20V, 24V.
SEMICONDUCTOR TECHNICAL DATA KIA785AF/API~KIA7824AF/API BIPOLAR LINEAR INTEGRATED THREE TERMINAL POSITIVE VOLTAGE REGULATORS 5V, 6V, 7V, 8V, 9V, 1V, 12V, 15V, 18V, 2V, 24V. FEATURES Internal Thermal Overload
Problem / Solution. The problem:
Problem / Solution Solar Photovoltaic (PV) technology has shown significant development in recent years and this has led to many UK homeowners investing in Solar PV installations. Solar electricity is
38 SERIES. Relay interface modules 0.1-2 - 3-5 - 6-8 - 16 A. EMR Electromechanical Relays. Common features. SSR Solid State Relays. 6.
38 Relay interface modules 0.1-2 - 3-5 - 6-8 - 16 A 38 Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit 6.2 mm wide EMR - DC, AC or AC/DC
SX460. Generator Automatic Voltage Regulator Operation Manual
SX460 Generator Automatic Voltage Regulator Operation Manual Self Excited Automatic Voltage Regulator Compatible with Newage SX460* * Use for reference purpose only and not a genuine Newage product. 1.
LED light engine / OLED LED compact. Umodule STARK CLE 120-2000 CLASSIC / CLE 130-2500 CLASSIC umodule CLE
Umodule STARK CLE 12-2 CLASSIC / CLE 13-25 CLASSIC umodule CLE Product description Designed for diffuser downlights and wallmounted luminaires Ideal to realise simple luminarie designs For easy adaptation
Analogue Input, 4-fold, MDRC AE/S 4.1, GH Q605 0054 R0001
Analogue Input, -fold, MDRC, GH Q605 005 R0001 The analogue input is a DIN rail mounted device for insertion in the distribution board. It is connected to the EIB via the bus connecting terminal supplied.
PINNING - TO220AB PIN CONFIGURATION SYMBOL
BTA4 series GENERAL DESCRIPTION QUICK REFERENCE DATA Passivated triacs in a plastic envelope, SYMBOL PARAMETER MAX. MAX. UNIT intended for use in applications requiring high bidirectional transient and
50W EdiStar. Approved By Customer. Designer Checker Approval. Ultra High Power LED
Ultra High Power LED 50W EdiStar EdiStar Emitter Approved By Customer Designer Checker Approval Date:2006/12/04 Version:Preliminary V0.1 4F, No. 800, Chung-Cheng Rd, Chung-Ho, Taipei 235, Taiwan Tel: 886-2-8227-6996
U LED modules, converters and systems GENERAL ILLUMINATION. Umodule SPOT P330-2 umodule SPOT PHASED OUT NTC
Product description Spotlights Downlights High-flux LED module Narrow colour temperature tolerance band Compact design Excellent thermal management 1 NTC for temperature control High-power LED in chip-on-board
LAUBE TECHNOLOGY DRY REED RELAYS
LAUBE TECHNOLOGY DRY REED RELAYS CONTACT FORM CURRENT PART SERIES PAGE #'S (1A) SPST-NO 1 AMP D41A...0L 147~148 (Link) (1A) SPST-NO 1 AMP D71A.1.0 149~150 (Link) (1A) SPST-NO 1 AMP F51A.100 151~152 (Link)
Bulletin 150 SMC Flex Smart Motor Controller Specifications
Specifications Specifications Standard Features Optional Features Installation Setup Communications Power Wiring Control Wiring Keypad Software Starting and Stopping Modes Protection and Diagnostics Metering
Series AMEPR30-AZ up to 2.5A AC-DC / DC-DC LED Driver / Converter
FEATURES: Click on Series name for product info on aimtec.com Models Single output Model Max Output Power (W) 1 AC-DC Constant Current or Constant Over temperature protection Voltage LED Driver Over current
10MQ100N SCHOTTKY RECTIFIER. I F(AV) = 2.1Amp V R = 100V. Bulletin PD-20520 rev. M 07/04. Major Ratings and Characteristics. Description/ Features
0MQ00N SCHOTTKY RECTIFIER 2. Amp I F(AV) = 2.Amp V R = 00V Major Ratings and Characteristics Characteristics 0MQ00N Units I F DC 2. A V RRM 00 V I FSM @ tp = 5 µs sine 20 A V F @.5Apk, T =25 C 0.68 V J
ST Series POWER SUPPLIES USER INSTRUCTIONS
Introduction These instructions detail the installation and operation requirements for the ST20 & ST35 power supplies. These have been designed for operation in RV s providing a DC power system, with optional
U LED modules, converters and systems GENERAL ILLUMINATION. Umodule SPOT P340-2 umodule SPOT PHASED OUT NTC 42.25 37 11 5.75 3.5 5.15 37.89 39.
Product description Spotlights Downlights High-flux LED module Narrow colour temperature tolerance band Compact design Excellent thermal management 1 NTC for temperature control High-power LED in chip-on-board
logic level for RCD/ GFI/ LCCB applications
logic level for RCD/ GFI/ LCCB applications BT68W series GENERAL DESCRIPTION QUICK REFERENCE DATA Glass passivated, sensitive gate SYMBOL PARAMETER MAX. MAX. MAX. MAX. UNIT thyristors in a plastic envelope
logic level for RCD/ GFI applications
logic level for RCD/ GFI applications BT68 series GENERAL DESCRIPTION QUICK REFERENCE DATA Glass passivated, sensitive gate SYMBOL PARAMETER MAX. MAX. MAX. MAX. UNIT thyristors in a plastic envelope, intended
DLP-PU/E Instruction Manual
Instruction Manual BEFORE USING THE POWER SUPPLY UNIT Pay attention to all warnings and cautions before using the unit. Incorrect usage could lead to an electrical shock, damage to the unit or a fire hazard.
PowerAmp Design. PowerAmp Design PAD135 COMPACT HIGH VOLATGE OP AMP
PowerAmp Design COMPACT HIGH VOLTAGE OP AMP Rev G KEY FEATURES LOW COST SMALL SIZE 40mm SQUARE HIGH VOLTAGE 200 VOLTS HIGH OUTPUT CURRENT 10A PEAK 40 WATT DISSIPATION CAPABILITY 200V/µS SLEW RATE APPLICATIONS
STRATO LED Drivers 70W, Single output
Features STRATO switch mode driver technology is designed to generate one constant current output from a wide range AC input. The size and performance of these products make them the ideal choice for LED
Positive-guided relay outputs: 3 safety contacts (N/O), instantaneous. 1 auxiliary contact (N/C), instantaneous
Safety relay for monitoring E-STOP pushbuttons. Approvals Unit features Positive-guided relay outputs: 3 safety contacts (N/O), instantaneous 1 auxiliary contact (N/C), instantaneous Safe separation of
Type Sealing Poles Contacts Rated voltage Model Standard d Flux-tight 4 poles oes 3PST-NO, SPST-NC 24 VDC G7SA-3A1B 3PST-NO, 3PST-NC
Safety Relay Slim Safety Relays Conforming to EN Standards The forcibly guided contact in the assures safe operation (EN50205 Class A, approved by VDE.) Ideal for use in safety circuits in press machinery,
MAXIMUM LOAD CURRENT 1 A SN SERIES
SOLID STATE RELAY (I/O Module) MAXIMUM LOAD CURRENT 1 A SN SERIES RoHS compliant FEATURES I/O modules for interface between CPU and external input devices or loads Ultra slim and light weight, SIL s type
Characteristics Values Units. Rectangular waveform 0.5 A. range - 55 to 150 C
Bulletin I075 rev. C 05/06 IR0530CSPTRPbF 0.5 Amp 30 Volt Features Ultra Low V F To Footprint Area Very Low Profile (
Contents. Document information
User Manual Contents Document information... 2 Introduction... 3 Warnings... 3 Manufacturer... 3 Description... Installation... Configuration... Troubleshooting...11 Technical data...12 Device Scope: PCB
S102S02 Series S202S02 Series
SS Series Non-zero cross type is also available. (SS1 Series/ SS1 Series) IT(rms) A, Zero Cross type SIP pin Triac output SSR Description SS Series and Solid State Relays (SSR) are an integration of an
Electrical Specifications
Electrical Specifications 913701213402 Max. Output Power (W) Output Voltage (V) Output Current (A) Tcase Max Max Input Current at 120V (A) Max. Input Power (W) Inrush Current (A pk - 50% µ s) Max. THD
DATA SHEET. TDA1518BQ 24 W BTL or 2 x 12 watt stereo car radio power amplifier INTEGRATED CIRCUITS
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 July 1994 GENERAL DESCRIPTION The is an integrated class-b output amplifier in a 13-lead single-in-line (SIL) plastic power package.
Three-phase monitoring relay CM-PFE
Data sheet Three-phase monitoring relay CM-PFE The CM-PFE is a three-phase monitoring relay that monitors the phase parameter phase sequence and phase failure in three-phase mains. 2CDC 251 005 S0012 Characteristics
0.8 U N /0.5 U N 0.8 U N /0.5 U N 0.8 U N /0.5 U N 0.2 U N /0.1 U N 0.2 U N /0.1 U N 0.2 U N /0.1 U N
55 Series - General purpose relays 7-10 A Features 55.12 55.13 55.14 Printed circuit mount, general purpose 2, 3 & 4 Pole relays 55.12-2 Pole 10 A 55.13-3 Pole 10 A 55.14-4 Pole 7 A AC coils & DC coils
40 Series - Miniature PCB/Plug-in relays 8-10 - 16 A. Features 40.31 40.51 40.52
Features 40.31 40.51 40.52 1 & 2 Pole relay range 40.31-1 Pole 10 A (3.5 mm pin pitch) 40.51-1 Pole 10 A (5 mm pin pitch) 40.52-2 Pole 8 A (5 mm pin pitch) PCB mount - direct or via PCB socket 35 mm rail
Type: EASY719 DC RC Article No.: 274119. Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC. Description
Type: EASY719 DC RC Article.: 274119 Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC Description 12 digital inputs (4 inputs available as analog inputs) 6 relay outputs LCD display
C106 Series. Sensitive Gate Silicon Controlled Rectifiers
C6 Series Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control;
WINGLIKE ELECTRONICS CO.,LTD
WINGLIKE ELECTRONICS CO.,LTD SPECIFICATION FOR APPROVAL AC/DC ADAPTOR CUSTOMER: CUSTOMER SPECS INPUT: 100-240V AC 50-60HZ, 5V/2A ADAPTOR OUR MODEL NO.: GM-050200 (UL) E321192 SPECIFICATION NO.: WL1105102
BTW67 and BTW69 Series
BTW67 and BTW69 Series STNDRD 50 SCRs MIN FETURES: Symbol Value Unit I T(RMS) 50 V DRM /V RRM 600 to 1200 V G K I GT 80 m G K DESCRIPTION vailable in high power packages, the BTW67 / BTW69 Series is suitable
CONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (4-20 ma Input Version)
TECHNICAL DATASHEET #TD1102AX CONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (4-20 ma Input Version) Part Number: Connector Amplifier CAPV-H-4-20MA-x complete with cable CAPV-4C-yM Where: x = current output
DMX-K-DRV. Integrated Step Motor Driver + (Basic Controller) Manual
DMX-K-DRV Integrated Step Motor Driver + (Basic Controller) Manual DMX-K-DRV Manual page 1 rev 1.33 COPYRIGHT 2007 ARCUS, ALL RIGHTS RESERVED First edition, June 2007 ARCUS TECHNOLOGY copyrights this document.
ABB 1. Three-phase monitoring relay CM-PFS. Data sheet. Features. Approvals. Marks. Order data. Order data - Accessories. Application.
1SR 430 824 F9300 Features Monitoring of three-phase mains for phase sequence and failure Powered by the measuring circuit 2 c/o (SPDT) contacts 1 LED for status indication Approvals R: yellow LED - relay
Application Note AN-0994 Maximizing the Effectiveness of your SMD Assemblies
Application Note AN-0994 Maximizing the Effectiveness of your SMD Assemblies Table of Contents Page Method...2 Thermal characteristics of SMDs...2 Adhesives...4 Solder pastes...4 Reflow profiles...4 Rework...6
N-channel enhancement mode TrenchMOS transistor
FEATURES SYMBOL QUICK REFERENCE DATA Trench technology d V DSS = V Low on-state resistance Fast switching I D = A High thermal cycling performance Low thermal resistance R DS(ON) mω (V GS = V) g s R DS(ON)
Features. Symbol JEDEC TO-220AB
Data Sheet June 1999 File Number 2253.2 3A, 5V,.4 Ohm, N-Channel Power MOSFET This is an N-Channel enhancement mode silicon gate power field effect transistor designed for applications such as switching
33.6W Power over Ethernet Waterproof Adapter PoE Plus Single Port Injector for Outdoor Application
33.6W Power over Ethernet Waterproof Adapter PoE Plus Single Port Injector for Outdoor Application Features Compliant with the IEEE802.3at Standard -40 to +60 C Temperature Range Diagnostic LEDs Full Protection
S101D01/S101D02 S201D01/S201D02
S1D1/S1D/S1D1/S1D S1D1/S1D S1D1/S1D 1-Pin DIP Type SSR for Low Power Control Features 1. Compact ( 1-pin dual-in-line package type). RMS ON-state current I T : 1.Arms 3. Built-in zero-cross (S1D, S1D ).
How To Select A Solid State Relay For A Three Phase Resistive Load
pero 1 Three Phase Solid State Relays & Their Application in Three Phase Heating Circuits By Paul Bachman, Fellow Engineer, Dr. Oscar Montero, R&D Manager, and Doug Sherman, FSAE Manager, Crydom, Inc.