HIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT

Transcription

1 HIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT SERIES RF00 RF00D RF00DD RF0 RF0D RF0DD RELAY TYPE Repeatable, RF relay Repeatable, RF relay with internal diode for coil transient suppression Repeatable, RF relay with internal diodes for coil transient suppression and polarity reversal protection Sensitive, repeatable, RF relay Sensitive, repeatable, RF relay with internal diode for coil transient suppression Sensitive, repeatable, RF relay with internal diodes for coil transient suppression and polarity reversal protection DESCRIPTION The ultraminiature RF00 and RF0 relays are designed to provide improved RF signal switching repeatability over the frequency range. These relays are engineered for use in RF attenuator, RF switch matrices, ATE and other applications that require dependable high frequency signal fidelity and performance. The RF00 and RF0 feature: High repeatability Broader bandwidth Metal enclosure for EMI shielding High isolation between control and signal paths High resistance to ESD The following unique construction features and manufacturing techniques provide excellent robustness to environmental extremes and overall high reliability: Uniframe motor design provides high magnetic efficiency and mechanical rigidity Minimum mass components and welded construction provide maximum resistance to shock and vibration Advanced cleaning techniques provide maximum assurance of internal cleanliness Hermetically sealed Solder Dipped Leads, (RoHS compliant solder option available) The Series RF00D/RF0D and RF00DD/RF0DD relays have internal discrete silicon diodes for coil suppression and polarity reversal protection. This hybrid package reduces required PC board floor space by reducing the number of external components needed to drive the relay. Temperature (Ambient) Vibration (General Note I) Shock (General Note I) Enclosure Weight ENVIRONMENTAL AND PHYSICAL SPECIFICATIONS Storage Operating RF00 RF0 5 C to +5 C 55 C to +85 C 0 g s to 500 Hz 0 g s, ms half sine Hermetically sealed 0.09 oz. (.55g) max. 0. oz. (.5g) max. INTERNAL CONSTRUCTION UPPER STATIONARY CONTACT MOVING CONTACT LOWER STATIONARY CONTACT UNI-FRAME ARMATURE 00 TELEDYNE RELAYS (800) RF00/RF0 Page

2 TYPICAL RF CHARACTERISTICS (See RF Notes) 0 Isolation Across Contacts (RF Note ) Isolation Pole to Pole (RF Note 5) Insertion Loss (RF Note ) VSWR (RF Note ) VSW R RF00/RF0 Time Response (RF Note ) % ps reference Volt 0.5.ps propagation delay time ps pulse rise time 0% T ime ( ps) RF NOTES. Test conditions: a. Fixture:.0" copper clad, reinforced PTFE, RT/duroid 00 with SMA connectors. (RT/duroid is a registered trademark of Rogers Corporation.) b. Room ambient temperature. c. Terminals not tested were terminated with 50-ohm load. d. Contact signal level: 0 dbm. e. No. of test samples:.. Data presented herein represents typical characteristics and is not intended for use as specification limits.. Data is per pole, except for pole-to-pole data.. Data is the average from readings taken on all open contacts. 5. Data is the average from readings taken on poles with coil energized and de-energized.. Data is the average from readings taken on all closed contacts.. Test fixture effect de-embedded from frequency and time response data. RF00/RF0 Page SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 00 TELEDYNE RELAYS

3 TYPICAL RF REPEATABILITY PERFORMANCE (See RF Notes, and ) Million Cycle Repeatability ±0. db from DC to GHz 0. Typical repeatability of attenuation during life (normally open contacts) ±db MAX X MIN Number of cycles X0 0. Typical repeatability of insertion loss during life (normally closed contacts) ±db.00 MAX X MIN Number of cycles X0 RF NOTES. One million cycle repeatability data is based upon 9 observations with an average repeatability ±0.0 db and a range of ±0.09 db.. Repeatability of attenuation values were obtained from tests conducted in a 0 db attenuator network with a 0 dbm input signal.. Relay operates at frequencies higher than GHz with reduced RF performance characteristics.. Curves were developed from tests performed on a 0.0" copper clad, reinforced PTFE circuit board at 0 C (ref). The unutilized contacts were terminated in 50 ohms; characteristic impedance of measuring equipment is 50 ohms. The relays were mounted flush to the circuit board ground plane without the relay header soldered to the ground plane. 00 TELEDYNE RELAYS (800) RF00/RF0 Page

4 GENERAL ELECTRICAL SPECIFICATIONS C) Contact Arrangement Rated Duty Contact Resistance Contact Load Rating Contact Life Ratings Coil Operating Power Operate Time Form C (DPDT) Continuous 0.5 Ω max. Resistive: Amp/8Vdc Low level: 0 to 50 0 to 50 mv 0,000,000 cycles (typical) at low level RF00: 50 mw typical at nominal rated voltage RF0: 00 mw typical at nominal rated voltage RF00:.0 ms max. RF0:.0 ms max. Release Time RF00:.0 ms max. RF00D, RF00DD:.0 ms max. RF0:.0 ms max. RF0D, RF0DD:.5 ms max. Intercontact Capacitance 0. pf typical Insulation Resistance,000 MΩ min. between mutually isolated terminals Dielectric Strength 50 Vrms (0 atmospheric pressure Negative Coil Transient (Vdc) RF00D/RF0D,RF00DD/RF0DD.0 max Diode P.I.V. (Vdc) RF00D/RF0D,RF00DD/RF0DD 0 min. DETAILED ELECTRICAL SPECIFICATIONS (@5 C) BASE PART NUMBERS (RF00, RF00D, RF00DD) RF00-5 RF00D-5 RF00DD-5 RF00- RF00D- RF00DD- Coil Voltage, Nominal (Vdc) RF00, RF00D Coil Resistance (Ohms ±0%) RF00DD (General Note II) 9 90 Coil Current (madc@ 5 C) Min (RF00DD Series) Max Pick-up Voltage (Vdc max.) RF00, RF00D, RF00DD. 9.0 BASE PART NUMBERS (RF0, RF0D, RF0DD) RF0-5 RF0D-5 RF0DD-5 RF0- RF0D- RF0DD- Coil Voltage, Nominal (Vdc) Coil Resistance (Ohms ±0%) RF0, RF0D RF0DD (General Note II) 850 Coil Current (madc@ 5 C) Min (RF0DD Series) Max Pick-up Voltage (Vdc max.) RF0, RF0D, RF0DD. 9.0 RF00/RF0 Page SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 00 TELEDYNE RELAYS

5 OUTLINE DIMENSIONS.0 (9.0) DIA. MAX..5 (8.5) DIA. MAX. H RF00:.5 (.99) RF0:.85 (9.8).05 (.89) REF.0 (.9) REF WIRE LEAD:.5 (9.05) MIN..00 (5.08) ±.00 (.5) DIA. ± TYP (.05).0 (.).00 (.0) DIA. DIMENSIONS ARE SHOWN IN INCHES (MILLIMETERS) (Viewed from Terminals) SCHEMATIC DIAGRAMS RF00/RF0 RF00D/RF0D RF00DD/RF0DD NOTES:. DIMENSIONS ARE IN INCHES, METRIC EQUIVALENTS SHOWN IN [ ].. POSTITIONS 5 AND 0 ARE FOR UNINSULATED CASE GROUND OPTIONS.. NO PROTRUSION BELOW BOTTOM OF HEADER WHEN GROUND PINS ARE INSTALLED. TO ORDER THE CASE GROUND OPTION, AFTER THE SERIES DESIGNATOR, ADD Y TO THE PART NUMBER FOR POSITION 5 OR Z TO THE PART NUMBER FOR POSITION 0. Teledyne Part Numbering System for RF00/RF0 Relays Relay Series RF0 D X - 5 / S R D = Internal diode for coil transient suppression DD = Internal diode for coil transient suppression and polarity reversal protection Ground Pin Option (See Appendix A) Q = Solder-Coated Leads G = Gold-Plated Leads (RoHS Compliant) R = RoHS Compliant Solder S = 0.8 Leads No Suffix = 0.5 Leads Nominal Coil Voltage General Note: Parts ordered without suffix may be supplied with Solder-Coated or Gold-Plated leads Parts ordered with Solder-Coated leads will have (Sn0/Pb0) Parts ordered with RoHS Solder-Coated leads will have (Sn99./Cu0.) GENERAL NOTES I. Relays will exhibit no contact chatter in excess of 0 μsec or transfer in excess of μsec. II. For reference only. Coil resistance not directly measureable at relay terminals due to internal series diode. 00 TELEDYNE RELAYS (800) RF00/RF0 Page 5

6 TYPICAL SIGNAL INTEGRITY CHARACTERISTICS Normally Closed (Typ.) +0 mv 0 V -0 mv 0 ps 0 ps 80 ps 0 ps 0 ps Eye Height Eye Width SNR Jitter P-P 5. mv 90.8 ps ps Normally Open (Typ.) +0 mv 0 V -0 mv 0 ps 0 ps 80 ps 0 ps 0 ps Eye Height Eye Width SNR Jitter P-P 50.9 mv 88. ps ps PATTERN GENERATOR SETTINGS 0 Gbps Random Pulse Pattern Generator - PRBS signal PRBS output of 00 mv (nominal) P-P RF PCB effect (negligible) not removed from measurement Data shown is typical of both poles RF00/RF0 Page SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 00 TELEDYNE RELAYS