LED light engine / OLED LED compact. Umodule STARK CLE CLASSIC / CLE CLASSIC umodule CLE

Transcription

1 Umodule STARK CLE 12-2 CLASSIC / CLE CLASSIC umodule CLE Product description Designed for diffuser downlights and wallmounted luminaires Ideal to realise simple luminarie designs For easy adaptation to existing luminarie architecture Luminarie body can act as heat sink Efficacy of the module up to 115 lm/w High colour rendering index CRI > 8 Small colour tolerance MacAdam 3 4 Colour temperatures 3, and 4, K Long life-time: 5, hours, 5-year guarantee È Standards, page 3 For colour temperatures and tolerances, page 6 CLE 12 CLE 13 Typical application 1

2 D D LED light engine / OLED Umodule STARK CLE 12-2 CLASSIC / CLE CLASSIC umodule CLE Technical data Beam characteristic 12 Ambient temperature ta C Typ. point 65 C Risk group (EN 62471:28) 1 Type of protection IP 65,38 35,25 Ø4,2 Ø ,25 75,5 Ø12 CLE 12 Ø4,2 Ø ,38 4, ,25 75,5 Ø13 CLE 13 Ordering data Type Article number Colour temperature Packaging, carton Weight per pc. STARK-CLE CLA , K 2 pc(s)..31 kg STARK-CLE CLA , K 2 pc(s)..32 kg STARK-CLE CLA , K 15 pc(s)..37 kg STARK-CLE CLA , K 15 pc(s)..36 kg Specific technical data Type Operating mode at 7 ma Photometric code Typ. luminous flux at = 25 C 1 Typ. luminous flux at = 65 C 1 Typ. forward Min. forward current 123 voltage at = 65 C Max. forward voltage at = 25 C Typ. power consumption at = 65 C 1 Luminous efficacy module at 25 C Luminous efficacy module at 65 C Luminous efficacy system at 65 C Colour rendering index CRI STARK-CLE CLA 83/349 2,8 lm 1,98 lm 7 ma 21.5 V 29. V 17.7 W 115 lm/w 112 lm/w 95 lm/w > 8 A+ STARK-CLE CLA 84/349 2,8 lm 1,98 lm 7 ma 21.5 V 29. V 17.7 W 115 lm/w 112 lm/w 95 lm/w > 8 A+ STARK-CLE CLA 83/349 2,6 lm 2,48 lm 7 ma 26.9 V 36.9 V 22.1 W 115 lm/w 112 lm/w 99 lm/w > 8 A+ STARK-CLE CLA 84/349 2,6 lm 2,48 lm 7 ma 26.9 V 36.9 V 22.1 W 115 lm/w 112 lm/w 99 lm/w > 8 A+ 1 Tolerance range for optical and electrical data: ±1 %. 2 Max. permissible repetitive peak current: 9 ma. 3 Max. permissible surge current: 1.2 A, duration max. 1 ms. 4 Integrated measurement over the whole module. Energy classification 2

3 Standards EN 6231 EN IEC Photometric code Key for photometric code, e. g. 83 / 449 EOS/ESD safety guidelines The device / module contains components that are sensitive to electrostatic discharge and may only be installed in the factory and on site if appropriate EOS/ESD protection measures have been taken. No special measures need be taken for devices/modules with enclosed casings (contact with the pc board not possible), just normal installation practice. Please note the requirements set out in the document EOS / ESD guidelines (Guideline_EOS_ESD.pdf) at: ht:// 1 st digit 2 nd + 3 rd digit 4 th digit 5 th digit 6 th digit Lumen maintanance after 25% Code CRI McAdam after of the life-time (max.6h) Colour temperature in McAdam 25% of the Code Remaining lumen Kelvin x initial life-time (max. 7 7 % ,h) 8 8 % % Heat sink values Umodule STARK CLE 12 ta Forward current Rth, hs-a Cooling area 25 C 65 C 7 ma 3. K/W 222 cm² 35 C 65 C 7 ma 2.2 K/W 33 cm² 45 C 65 C 7 ma 1.4 K/W 476 cm² Thermal design and heat sink The rated life of u products depends to a large extent on the temperature. If the permissible temperature limits are exceeded, the life of the umodule STARK CLE will be greatly reduced or the umodule STARK CLE may be destroyed. point, ambient temperature and life-time The temperature at reference point is crucial for the light ouut and life-time of a u product. Umodule STARK CLE 13 ta Forward current Rth, hs-a Cooling area 25 C 65 C 7 ma 2.4 K/W 278 cm² 35 C 65 C 7 ma 1.7 K/W 392 cm² 45 C 65 C 7 ma 1.1 K/W 66 cm² Notes The actual cooling surface can differ because of the material, the structural shape, outside influences and the installation situation. Depending on the heat sink a heat conducting paste or heat conducting film might be necessary to keep the specified temperature. For umodule STARK CLE a temperature of 65 C has to be complied in order to achieve an optimum between light ouut and life-time. Compliance with the maximum permissible reference temperature at the point must be checked under operating conditions in a thermally stable state. The maximum value must be determined under worst-case conditions for the relevant application. The tc and temperature of LED modules from Tridonic are measured at the same reference point. Mounting instruction None of the components of the umodule STARK CLE (substrate, LED, electronic components etc.) may be exposed to tensile or compressive stresses. Max. torque for fixing:.5 Nm. The LED modules are mounted with 3 screws per module. In order not to damage the modules only rounded head screws and an additional plastic flat washer should be used. Chemical substance may harm the LED module. Chemical reactions could lead to colour shift, reduced luminous flux or a total failure of the module caused by corrosion of electrical connections. Materials which are used in LED applications (e.g. sealings, adhesives) must not produce dissolver gas. They must not be condensation curing based, acetate curing based or contain sulfur, chlorine or phthalate. Avoid corrosive atmosphere during usage and storage. 3

4 Thermal behaviour storage temperature C operating temperature ta C (at typ. current) 65 C tc max. (at typ. current) 8 C max. humidity*... 7 % * not condensed If [ma] tc [ C] Life-time, lumen maintenance and failure rate The light ouut of an LED Module decreases over the life-time, this is characterized with the L value. L7 means that the LED module will give 7 % of its initial luminous flux. This value is always related to the number of operation hours and therefore defines the lifetime of an LED module. As the L value is a statistical value and the lumen maintenace may vary over the delivered LED modules. The B value defines the amount of modules which are below the specific L value, e.g. L7B1 means 1 % of the LED modules are below 7 % of the inital luminous flux, respectivly 9 % will be above 7 % of the initial value. In addition the percentage of failed modules (fatal failure) is characterized by the C value. The F value is the combination of the B and C value. That means for F degradation and complete failures are considered, e.g. L7F1 means 1 % of the LED modules may fail or be below 7 % of the initial luminous flux. Selection of the LED Driver umodule STARK CLE can be operated either from SELV LED Drivers or from LED Drivers with LV ouut voltage. umodule STARK CLE are basic isolated up to 19 V against ground and can be mounted directly on earthed metal parts of the luminaire. If the max. ouut voltage of the LED Driver (also against earth) is above 19 V, an additional isolation between LED module and heat sink is required (for example by isolated thermal pads) or by a suitable luminaire construction. At voltages > 6 V an additional protection against direct touch (test finger) to the light emitting side of the module has to be guaranteed. This is typically achieved by means of a non removable light distributor over the module. Electrical supply/choice of LED Driver umodule STARK CLE from Tridonic are not protected against overvoltages, overcurrents, overloads or short-circuit currents. Safe and reliable operation can only be guaranteed in conjunction with a LED Driver which complies with the relevant standards. The use of uconverter from Tridonic in combination with umodule STARK CLE guarantees the necessary protection for safe and reliable operation. If a LED Driver other than Tridonic uconverter is used, it must provide the following protection: Short-circuit protection Overload protection Overtemperature protection umodule STARK CLE must be supplied by a constant current LED Driver. Operation with a constant voltage LED Driver will lead to an irreversible damage of the module. Wrong polarity can damage the umodule STARK CLE. With parallel wiring tolerance-related differences in ouut are possible (thermal stress of the module) and can cause differences in brightness. If one module fails, the remaining modules may be overloaded. Lumen maintenance for Umodule STARK CLE 12 Forward current L9 / F1 temperature L9 / F5 L8 / F1 L8 / F5 L7 / F1 L7 / F5 7 ma 65 C 9, h 19, h 17, h 38, h 26, h 5, h Lumen maintenance for Umodule STARK CLE 13 Forward current L9 / F1 temperature L9 / F5 L8 / F1 L8 / F5 L7 / F1 L7 / F5 7 ma 65 C 9, h 2, h 18, h 4, h 28, h 5, h Life-time declarations are informative and represent no warranty claim. 4

5 Wiring CLE 12 + Wiring CLE 13 + Wiring type and cross section The wiring can be solid cable with a cross section of.4 to.75 mm². For the push-wire connection you have to strip the insulation (6 7 mm). Loosen wire through twisting and pulling. wire preparation:.4.75 mm² Wiring example V AC 5/6 Hz L N PE Umodule STARK CLE 12 / mm Release of the wiring Press down the push button and remove the cable from front. + LED LED Uconverter LCI... N L SEC PRI + Forward current vs. forward voltage (CLE 12) 9 Forward current vs. forward voltage (CLE 13) Forward current [ma] Forward current [ma] Forward voltage [V] Forward voltage [V] 11 Rel. forward voltage [V] tc [ C] 5

6 Relative luminous flux 11 rel. luminous flux [%] [ C] 5 75 Relative luminous flux vs. operating current (CLE 12) Relative luminous flux vs. operating current (CLE 13) rel. luminous flux [%] rel. luminous flux [%] Operating current [ma] Operating current [ma] The diagrams based on statistic values. The real values can be different. Optical characteristics Umodule STARK CLE The optical design of the umodule STARK CLE product line ensures optimum homogenity for the light distribution. Light distribution relative intensity Iv/Iv, max The colour temperature is measured over the complete module. The single LED light points can be outside of 3SDCM. To ensure an ideal mixture of colours and a homogenious light distribution a suitable optic (e. g. PMMA diffuser) and a sufficient spacing between module and optic (typ. 5 cm) should be used D-Data, photometric data and Design-in guide available on request or go to www. tridonic.com 6

7 Coordinates and tolerances according to CIE 1931 The specified colour coordinates are measured integral by a current impulse with typical values of module and a duration of ms. The ambient temperature of the measurement is ta = 25 C. The measurement tolerance of the colour coordinates are ±.1. 3, K x y Centre ,425,42,415,4,45,4,395,39 norm. intensity [%] ,385,415,42,425,43,435,44,445,45, MacAdam Ellipse: 3SDCM wave length [nm] 4, K x y Centre ,4,45,4,395,39,385,38,375 norm. intensity [%] ,37,365,37,375,38,385,39,395,4, MacAdam Ellipse: 3SDCM wave length [nm] 7