Parker Series 2A Air Cylinder

Transcription

1 Parker Series ir ylinder hen the job calls for reliable, heavy-duty performance, specify Series. 00,000 psi yield strength chrome-plated, case-hardened piston rod.,000 psi yield strength rod-end stud with rolled threads. 00,000 psi yield strength tie rods. ith construction like this, the Parker Series is rated for air service to 0 psi. This is one heavy-duty air cylinder that's really heavy duty. They're truly premium quality cylinders, factory prelubricated for millions of maintenance-free cycles. nd to make sure every cylinder is premium quality, we subject each and every one not just batch samples to tough inspection and performance tests. See pages and for the inside story on all the features that make Series the high performance, long lasting choice for all your heavy-duty air applications. or additional information call your local Parker ylinder Distributor.

2 Series Heavy Duty ir ylinders Standard Specifications Heavy Duty Service NSI/(NP) T..- Specifications and Mounting Dimension Standards Standard onstruction Square Head Tie od Design Nominal Pressure Up to 0 PSI ir Service Standard luid iltered ir Standard Temperature -0. to +. Bore Sizes " through " (Larger sizes available) In line with our policy of continuing product improvement, specifications in this catalog are subject to change. Tie ods xtended Head nd Style TB vailable Mounting Styles Tie ods xtended ap nd Style T Tie ods xtended Both nds Style TD Specifications/ Mountings Piston od Diameter /" through /" Mounting Styles standard styles at various application ratings Strokes vailable in any practical stroke length ushions Optional at either end or both ends of stroke. "loat heck" at cap end. od nds Three Standard hoices Specials to Order See section, Operating luids and Temperature ange for higher temperature service. Note: Series ir ylinders fully meet NSI/(NP) T..- Specifications and Mounting Dimension Standards for Square Head Industrial luid Power ylinders. Parker Style TB, B, HB,, DB, and BB are available in " bore size, see page. Head ectangular lange Style (NP MX) "-", Page 0 "-", Page Head Square lange ap ectangular lange ap Square lange Side Lug Style B (NP MX) "-", Page 0 "-", Page (NP MX) Style H "-", Page 0 "-", Page (NP M) Style HB "-", Page 0 Style (NP M) "-", Page "-", Page (NP M) "-", Page 0 (NP M) "-", Page "-", Page (NP MS) enterline Lugs Side Tapped Side nd ngles Side nd Lugs Style Style Style B "-", Page "-", Page Style /"-", Page (NP MS) "-", Page ap ixed levis Style BB (NP MS) ap Detachable levis "-", Page "-", Page (NP MS) Style B Head Trunnion "-", Page "-", Page 0 (NP MS) Style D ap Trunnion "-", Page "-", Page Style DB (NP MP) "-", Page 0 "-", Page 0 (NP MP) "-", Page 0 (NP MT) "-", Page "-", Page (NP MT) "-", Page "-", Page Intermediate ixed Trunnion Spherical Bearing Double od ylinders Style DD Style SB Style TB Shown (NP MT) /"-", Page "-", Page /"-", Page "-", Page Most of the above illustrated mounting styles are available in double rod cylinders. See atalog Page. or ylinder Division Plant Locations See Page II.

3 The inside story on why Series is your best choice in heavy duty pneumatic cylinders Piston od Stud urnished on " diameter rods and smaller when standard style # rod end threads are required or on /" diameter rods and smaller when style # threads are required. lso available in times the catalog dimension length. Studs have rolled threads and are made from high strength steel. naerobic adhesive is used to permanently lock the stud to the piston rod. Primary Seal Unique Serrated Lipseal is a proven leakproof design, (Parker Patent #) completely self-compensating and self-relieving to withstand variations and conform to mechanical deflection that may occur. Steel Head Bored and grooved to provide concentricity for mating parts. Ports NPT ports are standard. nd Seals Pressure-actuated cylinder body-to-head and cap O rings. ewel od land ssembly xternally removable without cylinder disassembly. Long bearing surface is inboard of the seals, assuring positive lubrication from within the cylinder. n O ring is used as a seal between gland and head, and also serves as a prevailing torque-type lock. Secondary Seal Double-Service iperseal (Parker Patent #0) acts as a secondary pressure seal on the extend stroke and cleans the rod on the return stroke. djustable floating cushions ushions are optional, and can be supplied at head end, cap end, or both ends without change in envelope or mounting dimensions. ll Parker cushions are adjustable. The Series cylinder design incorporates the longest cushion sleeve and cushion spear that can be provided in the standard envelope without decreasing the rod bearing and piston bearing lengths. () hen a cushion is specified at the head end: a. self-centering sleeve is furnished on the piston rod assembly. b. needle valve is provided that is flush with the side of the head when wide open. It may be identified by the fact that it is socket-keyed. It is located on side number, in all mounting styles except D, DB, DD, and. In these styles it is located on side number. c. springless check valve is provided that is also flush with the side of the head and is mounted High Strength Tie ods Made from 00,000 psi minimum yield steel with rolled threads for added strength. djustable loating ushions ushions are optional and can be supplied at head end, cap end, or both ends without change in envelope or mounting dimensions. The ylinder Body Hard chromeplated bore, steel tubing honed to a micro inch finish on /" through " bore sizes. " bore size is aluminum with hardcoated bore. adjacent to the needle valve except on certain bores of mounting style where it is mounted opposite the needle valve. It may be identified by the fact that it is slotted. d. The check and needle valves are interchangeable in the head. () hen a cushion is specified at the cap end: a. cushion spear is provided on the piston rod assembly. b. float check self-centering bushing is provided which incorporates a large flow check valve for fast out-stroke action. c. socket-keyed needle valve is provided that is flush with the side of the cap when wide open. It is located on side number in all mounting styles except D, DB, DD, and. In these styles it is located on side number. or additional information call your local Parker ylinder Distributor.

4 Piston od Medium carbon steel, induction case-hardened, hard chrome-plated and polished to 0 MS finish. Piston rods are made from 0,000 to 00,000 psi minimum yield material in /" through " diameters. Larger diameters vary between,000 and 0,000 psi minimum material, depending on rod diameter. The piston thread equals the catalog style # rod end thread for each rod diameter to assure proper piston-to-rod thread strength. Two wrench flats are provided for rod end attachment. Ports NPT ports are standard. Steel ap Bored and grooved to provide concentricity for mating parts. lloy Steel Tie od Nuts lign--roove (Patent #0) /" wide surface machined at each end of the cylinder body. Makes precise mounting quick and easy. One-Piece Nodular Iron Piston The wide piston surface contacting cylinder bore reduces bearing loads. naerobic adhesive is used to permanently lock and seal the piston to the rod. Piston Lipseal ully dynamic and self-compensating for variations in pressure, mechanical deflections and wear. The exclusive ewel gland gives you longer cylinder life, better performance and lower costs. n extra-long inboard bearing surface insures lubrication from within the cylinder. Outboard of the bearing surface are two leakproof seals The Lipseal and iperseal. The serrated Lipseal (primary seal) is completely self-compensating and self-relieving. It adjusts to mechanical deflections or any pressure variation from near-zero to rated operating pressure. The result is positive, no-leak sealing regardless of conditions. The iperseal does double duty. On the advance stroke, it acts as a secondary pressure seal. On the return, it wipes away any dirt on the rod. This means less wear on bearing surfaces and internal parts. Longer life for working parts. nd, less loss of fluid. Plus, you can replace a ewel gland without removing the tie rods or the retainer. ust a few twists with a spanner wrench does the job. Prelubricated earing Surfaces Parker Series ir ylinders are factory prelubricated. Lube--yl applied to seals, piston, cylinder bore, piston rod and gland surfaces provides lubrication for normal operation. Lube--yl has been field and laboratory tested, and is recommended by Parker for air cylinders where lubricant should remain in the cylinder and not be expelled into the atmosphere. Piston with etainer Nut Optional at extra charge. ushion Length ylinder Bore (Inches) od Diameter (Inches) od Number ushion Length (Inches) Head ap ylinder Bore (Inches) od Diameter (Inches) od Number ushion Length (Inches) Head ap / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / 0 / / / / / 0 / / / / / / / / / / Head end cushions for rod diameters not listed have cushion lengths with the limits shown. or cushion selection and sizing see Section. or ylinder Division Plant Locations See Page II.

5 Tie od and ectangular lange Mountings " to " Bore Sizes Tie ods xtended Style TB (NP Style MX) Basic Mounting (T) NP MX0 no tie rods extended can be supplied upon request. Series Heavy Duty ir ylinders ZB + STO P + STO LB + STO DD Head ectangular lange Style (NP Style M) BB Style TB (NP MX). Head Tie ods xtended, illustrated: Style T (NP MX), ap Tie ods xtended; and Style TD (NP MX), Both nds Tie ods xtended are also available. ll T styles can be dimensioned from Style TB drawing at right. U ZB + STO P + STO LB + STO T B HOLS ap ectangular lange Style H (NP Style M) Z + STO P + STO LB + STO U X T B HOLS od nd Dimensions see table Thread Style Thread Style (NP Style SM) (NP Style IM) Small Male Intermediate Male D NH LTS L N B high strength rod end stud is supplied on thread style through " diameter rods and on thread style through /" diameter rods. Larger sizes or special rod ends are cut threads. Style rod ends are recommended where the workpiece is secured against the rod shoulder. hen the workpiece is not shouldered, style rod ends are D NH LTS L N B Thread Style (NP Style S) Small emale D NH LTS recommended through " piston rod diameters and style rod ends are recommended on larger diameters. Use style for applications where female rod end threads are required. If rod end is not specified, style will be supplied. N B Special Thread Style Special thread, extension, rod eye, blank, etc., are also available. To order, specify Style and give desired dimensions for or, and L. If otherwise special, furnish dimensioned sketch. or additional information call your local Parker ylinder Distributor. 0

6 Series Heavy Duty ir ylinders Tie od and ectangular lange Mountings " to " Bore Sizes Table nvelope and Mounting Dimensions dd Stroke Bore BB DD NPT B T U LB P / / / / / / / / 0- / - /- / - / - /- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /.. / / -0 / / -0 / / / / / / / / / / / / /.0. / / / / / / / / ushions not available on " bore. On ", /", " and /" bore sizes, the head-end (only) pipe thread is not full depth on cylinders with No. rods. Minimum of three full threads available. " bore head dimension is /" x /". See page B0. Table nvelope and Table od Dimensions Mounting Dimensions Thread od xtensions and Pilot Dimensions dd Stroke od Style Style od Dia. & -.00 Bore No. B D L N X ZB Z (Std.) / / -0 / - /. / / / / / / / / / / / / -0 / -0 /. / / / / / / / / / / / (Std.) / / -0 / -0 /. / / / / / / / / / / - / - /. / / / / / / / / / (Std.) / / -0 / -0 /. / / / / / / / / / / / - - /. / / / / / / / / / / / / - / - /. / / / / / / / / / (Std.) / /-0 / -0 /. / / / / / / / / / / / / / - /-. / / / / / / / / / / / - / - /. / / / / / / / / / / / /- - /. / / / / / / / / / / / (Std.) / - /- /. / / / / / / / / / / / / - / - /. / / / / / / / / / / / /- - /. / / / / / / / / / / / / - /-. / / / / / / / / / / / (Std.) / - / - /. / / / / / / / / / / / /- / -. / / / / / / / / / / / / - - /. / / / / / / / / / / / / - / -. / / / / / / / / / / / /- / - /. / / / / / / / / / / (Std.) / - /- /. / / / / / / / / / / / / / - / - /. / / / / / / / / / / /- - /. / / / / / / / / / / / / - /-. / / / / / / / / / / / - / - /. / / / / / / / / / / / /- / -. / / / / / / / / / / / - /- /. / / / / / / / / / / (Std.) / / - - /. / / / / / / / / / / / /- -. / / / / / / / / / / / - /-. / / / / / / / / / / / / - / - /. / / / / / / / / / / /- / -. / / / / / / / / / / - /- /. / / / / / / / / / / - / - /. / / / / / / / Note: Shaded areas indicate non-standard rod sizes that are available and made to order. or ylinder Division Plant Locations See Page II.

7 Square lange Mountings " to " Bore Sizes Series Heavy Duty ir ylinders Head Square lange Style B (NP Style M) U ZB + STO P + STO LB + STO U T B HOLS T ap Square lange Style HB (NP Style M) Z + STO P + STO LB + STO U T U X B HOLS T od nd Dimensions see table Thread Style Thread Style (NP Style SM) (NP Style IM) Small Male Intermediate Male D NH LTS L N B high strength rod end stud is supplied on thread style through " diameter rods and on thread style through /" diameter rods. Larger sizes or special rod ends are cut threads. Style rod ends are recommended where the workpiece is secured against the rod shoulder. hen the workpiece is not shouldered, style rod ends are D NH LTS L N B Thread Style (NP Style S) Small emale D NH LTS recommended through " piston rod diameters and style rod ends are recommended on larger diameters. Use style for applications where female rod end threads are required. If rod end is not specified, style will be supplied. N B Special Thread Style Special thread, extension, rod eye, blank, etc., are also available. To order, specify Style and give desired dimensions for or, and L. If otherwise special, furnish dimensioned sketch. or additional information call your local Parker ylinder Distributor.

8 Series Heavy Duty ir ylinders Square lange Mountings " to " Bore Sizes Table nvelope and Mounting Dimensions dd Stroke Bore NPT B T U LB P / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / ushions not available on " bore. On ", /", " and /" bore sizes, the head-end (only) pipe thread is not full depth on cylinders with No. rods. Minimum of three full threads available. " bore head dimension is /" x /". See page B0. Table od Dimensions Table nvelope and Mounting Dimensions Thread od xtensions and Pilot Dimensions dd Stroke od Style Style od Dia. & -.00 Bore No. B D L N X ZB Z (Std.) / / -0 / - /. / / / / / / / / / / / / -0 / -0 /. / / / / / / / / / / / (Std.) / / -0 / -0 /. / / / / / / / / / / - / - /. / / / / / / / / / (Std.) / / -0 / -0 /. / / / / / / / / / / / - - /. / / / / / / / / / / / / - / - /. / / / / / / / / / (Std.) / /-0 / -0 /. / / / / / / / / / / / / / - /-. / / / / / / / / / / / - / - /. / / / / / / / / / / / /- - /. / / / / / / / / / / / (Std.) / - /- /. / / / / / / / / / / / / - / - /. / / / / / / / / / / / /- - /. / / / / / / / / / / / / - /-. / / / / / / / / / / / (Std.) / - / - /. / / / / / / / / / / / /- / -. / / / / / / / / / / / / - - /. / / / / / / / / / / / / - / -. / / / / / / / / / / / /- / - /. / / / / / / / / / / (Std.) / - /- /. / / / / / / / / / / / / / - / - /. / / / / / / / / / / /- - /. / / / / / / / / / / / / - /-. / / / / / / / / / / / - / - /. / / / / / / / / / / / /- / -. / / / / / / / / / / / - /- /. / / / / / / / / / / (Std.) / / - - /. / / / / / / / / / / / /- -. / / / / / / / / / / / - /-. / / / / / / / / / / / / - / - /. / / / / / / / / / / /- / -. / / / / / / / / / / - /- /. / / / / / / / / / / - / - /. / / / / / / / Note: Shaded areas indicate non-standard rod sizes that are available and made to order. or ylinder Division Plant Locations See Page II.

9 Side Lugs, enterline Lugs and Side Tapped Mountings " to " Bore Sizes Series Heavy Duty ir ylinders Side Lug Style (NP Style MS) US ZB + STO P + STO LB + STO ST S S TS SB S HOLS S S XS SU SS + STO SU S enterline Lugs Style (NP Style MS) US SB HOLS ZB + STO P + STO LB + STO ST S S TS S S S XS SU SS + STO SU S Side Tapped Style (NP Style MS) ZB + STO P + STO LB + STO TN NT THD, ND DP TPPD MT. HOLS XT SN + STO od nd Dimensions see table Thread Style Thread Style (NP Style SM) (NP Style IM) Small Male Intermediate Male D NH LTS L N B high strength rod end stud is supplied on thread style through " diameter rods and on thread style through /" diameter rods. Larger sizes or special rod ends are cut threads. Style rod ends are recommended where the workpiece is secured against the rod shoulder. hen the workpiece is not shouldered, style rod ends are D NH LTS L N B Thread Style (NP Style S) Small emale D NH LTS recommended through " piston rod diameters and style rod ends are recommended on larger diameters. Use style for applications where female rod end threads are required. If rod end is not specified, style will be supplied. N B Special Thread Style Special thread, extension, rod eye, blank, etc., are also available. To order, specify Style and give desired dimensions for or, and L. If otherwise special, furnish dimensioned sketch. or additional information call your local Parker ylinder Distributor.

10 Series Heavy Duty ir ylinders Side Lugs, enterline Lugs and Side Tapped Mountings " to " Bore Sizes Table nvelope and Mounting Dimensions dd Stroke Bore NPT NT SB ST SU S TN TS US LB P SN SS / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / 0- / -0 /- / - / - /- / - / -0 / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / ushions not available on " bore. On ", /", " and /" bore sizes, the head-end (only) pipe thread is not full depth on cylinders with No. rods. Minimum of three full threads available. Upper surface spot-faced for socket head screws. Mounting style not available in " bore. " bore head dimension is /" x /". See page B0. Table od Dimensions Thread od Style Style od Dia. & -.00 od xtensions and Pilot Dimensions Note: Mounting Shaded style areas not indicate available non-standard in " bore. rod sizes that are available and made to order. Table nvelope and Mounting Dimensions Bore No. B D L N ND XS XT ZB / (Std.) (Std.) / / / -0 / -0 / - / -0 / /.. / / / / / / / / / / / / / / / / / / / / / / -0 / - / -0 / - / /.. / / / / / / / / / / / / / / / / / / / (Std.) (Std.) / / / / -0 / - / - /-0 / -0 - / - / -0 / / / /.... / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / - /-. / / / / / / / / / / / - / - /. / / / / / / / / / (Std.) / /- / - - /- / /.. / / / / / / / / / / / / / / / / / / / / / - / - /. / / / / / / / / / / / /- - /. / / / / / / / / / (Std.) (Std.) (Std.) / / / / / / / / / / / / / - / - /- / - / - /- / - / - /- / - / - /- / - / - /- / - / - /- / - / - /- / - / - - / - / - /- / - - /- / - / - /- - - /- / - / - /- / - / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / dd Stroke / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / or ylinder Division Plant Locations See Page II.

11 Side nd ngles and Side nd Lugs Mountings " to " Bore Sizes Series Heavy Duty ir ylinders Side nd ngles Style B (NP Style MS) Z + STO X + STO P + STO LB + STO B HOLS S T H O T L S + STO L O Side nd Lugs Style (NP Style MS) Z + STO X + STO P + STO LB + STO T S S B HOLS O L S + STO L O od nd Dimensions see table Thread Style Thread Style (NP Style SM) (NP Style IM) Small Male Intermediate Male D NH LTS L N B high strength rod end stud is supplied on thread style through " diameter rods and on thread style through /" diameter rods. Larger sizes or special rod ends are cut threads. Style rod ends are recommended where the workpiece is secured against the rod shoulder. hen the workpiece is not shouldered, style rod ends are D NH LTS L N B Thread Style (NP Style S) Small emale D NH LTS recommended through " piston rod diameters and style rod ends are recommended on larger diameters. Use style for applications where female rod end threads are required. If rod end is not specified, style will be supplied. N B Special Thread Style Special thread, extension, rod eye, blank, etc., are also available. To order, specify Style and give desired dimensions for or, and L. If otherwise special, furnish dimensioned sketch. or additional information call your local Parker ylinder Distributor.

12 Series Heavy Duty ir ylinders Side nd ngles and Side nd Lugs Mountings " to " Bore Sizes Table nvelope and Mounting Dimensions dd Stroke Bore B H L O T B NPT L O S T S LB P S S / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / ushions not available on " bore. On ", /", " and /" bore sizes, the head-end (only) pipe thread is not full depth on cylinders with No. rods. Minimum of three full threads available. Mounting style B available in " bore for rod No. only. Mounting style B for " bore only is furnished with four mounting holes (two each end). enter holes omitted. " bore head dimension is /" x /". See page B0. Mounting style not available in " bore. Table nvelope and Table od Dimensions Mounting Dimensions Thread od xtensions and Pilot Dimensions od Style Style dd Stroke od Dia. & -.00 Bore No. B D L N X X Z Z (Std.) / / -0 / - /. / / / / / / / / / / / -0 / -0 /. / / / / / / / / (Std.) / / -0 / -0 /. / / / / / / / / / / / - / - /. / / / / / / / / (Std.) / / -0 / -0 /. / / / / / / / / / / / / - - /. / / / / / / / / / / / / - / - /. / / / / / / / / / (Std.) / /-0 / -0 /. / / / / / / / / / / / / / / - /-. / / / / / / / / / / - / - /. / / / / / / / / / / / /- - /. / / / / / / / / / / / (Std.) / - /- /. / / / / / / / / / / / / / - / - /. / / / / / / / / / / / /- - /. / / / / / / / / / / / / - /-. / / / / / / / / / / (Std.) / - / - /. / / / / / / / / / / / /- / -. / / / / / / / / / / / / - - /. / / / / / / / / / / / / - / -. / / / / / / / / / / / /- / - /. / / / / / / / / / / (Std.) / - /- /. / / / / / / / / / / / / / - / - /. / / / / / / / / / / /- - /. / / / / / / / / / / / / - /-. / / / / / / / / / / / / - / - /. / / / / / / / / / / / / /- / -. / / / / / / / / / / / - /- /. / / / / / / / / / / (Std.) / / - - /. / / / / / / / / / / /- -. / / / / / / / / / / / / - /-. / / / / / / / / / / / / - / - /. / / / / / / / / / / /- / -. / / / / / / / / / / / - /- /. / / / / / / / / / / / - / - /. / / / / / / / / Note: Mounting Shaded style areas B indicate available non-standard in " bore for rod sizes No. that only. are available and made to order. Mounting style not available in " bore. aution: hen using mounting styles B and, check clearance between mounting members and rod attachment or accessory. If necessary, specify longer rod extension to avoid interference with mounting members. or ylinder Division Plant Locations See Page II.

13 Trunnion Mountings " to " Bore Sizes Series Heavy Duty ir ylinders Head Trunnion Style D (NP Style MT) UT ZB + STO P + STO LB + STO TD TL TL X ap Trunnion Style DB (NP Style MT) UT ZB + STO P + STO LB + STO TD TL TL X + STO Intermediate ixed Trunnion Style DD (NP Style MT) UM ZB + STO P + STO LB + STO BD U TD TL TM TL XI od nd Dimensions see table Thread Style Thread Style (NP Style SM) (NP Style IM) Small Male Intermediate Male D NH LTS L N B high strength rod end stud is supplied on thread style through " diameter rods and on thread style through /" diameter rods. Larger sizes or special rod ends are cut threads. Style rod ends are recommended where the workpiece is secured against the rod shoulder. hen the workpiece is not shouldered, style rod ends are D NH LTS L N B Thread Style (NP Style S) Small emale D NH LTS recommended through " piston rod diameters and style rod ends are recommended on larger diameters. Use style for applications where female rod end threads are required. If rod end is not specified, style will be supplied. N B Special Thread Style Special thread, extension, rod eye, blank, etc., are also available. To order, specify Style and give desired dimensions for or, and L. If otherwise special, furnish dimensioned sketch. or additional information call your local Parker ylinder Distributor.

14 Series Heavy Duty ir ylinders Trunnion Mountings " to " Bore Sizes Table nvelope and Mounting Dimensions Style dd Stroke DD TD Min. Bore BD NPT -.00 TL TM UM UT U LB P Stroke / / / /.0 / / / / / / / / /.000 / / / / / / / / / / /.000 / / / / / / / / /.000 / / / / / / / / / / / / /.000 / / / / / / / / / / / / /.000 / / / / / / / / / / / /.000 / / / / / / / / / / / /. / / 0 / / / / / ushions not available on " bore. On ", /", " and /" bore sizes, the head-end (only) pipe thread is not full depth on cylinders with No. rods. Minimum of three full threads available. Mounting style not available in " bore. " bore head dimension is /" x /". See page B0. Table nvelope and Table od Dimensions Mounting Dimensions Thread od xtensions and Pilot Dimensions dd Stroke od Style Style od Dia. & -.00 Min. Bore No. B D L N X XI X ZB (Std.) / / -0 / - /. / / / / / / -0 / -0 /. / / / / / (Std.) / / -0 / -0 /. / / / / / - / - /. / / / / (Std.) / / -0 / -0 /. / / / / / / - - /. / / / / / - / - /. / / / / (Std.) / /-0 / -0 /. / / / / / / / - /-. / / / / / - / - /. / / / / / /- - /. / / / / (Std.) / - /- /. / / / / / / - / - /. / / / / / /- - /. / / / / / / - /-. / / / / (Std.) / - / - /. / / / / / /- / -. / / / / / - - /. / / / / / / - / -. / / / / /- / - /. / / / / (Std.) / - /- /. / / / / / / - / - /. / / / /- - /. / / / / / / - /-. / / / / / - / - /. / / / / / /- / -. / / / / - /- /. / / / (Std.) / / - - /. / / / / /- -. / / / / / - /-. / / / / / - / - /. / / / / / /- / -. / / / / - /- /. / / / / - / - /. / Note: Mounting Shaded style areas DD indicate not available non-standard in " bore. rod sizes that are available and made to order. Dimension XI to be specified by customer. / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / or ylinder Division Plant Locations See Page II.

15 levis Mountings " to " Bore Sizes Series Heavy Duty ir ylinders ap ixed levis Style BB (NP Style MP) Z + STO P + STO LB + STO D PIOT PIN HD HOM PLTD M L X + STO L M B The ", ", " and " bore sizes have tie rod nuts at both ends as shown. Tie rods thread into cap on all other bore sizes. ap Detachable levis Style B (NP Style MP) ZD + STO P + STO LB + STO D PIOT PIN HD HOM PLTD M L XD + STO L M B od nd Dimensions see table Thread Style Thread Style (NP Style SM) (NP Style IM) Small Male Intermediate Male D NH LTS L N B high strength rod end stud is supplied on thread style through " diameter rods and on thread style through /" diameter rods. Larger sizes or special rod ends are cut threads. Style rod ends are recommended where the workpiece is secured against the rod shoulder. hen the workpiece is not shouldered, style rod ends are D NH LTS L N B Thread Style (NP Style S) Small emale D NH LTS recommended through " piston rod diameters and style rod ends are recommended on larger diameters. Use style for applications where female rod end threads are required. If rod end is not specified, style will be supplied. N B Special Thread Style Special thread, extension, rod eye, blank, etc., are also available. To order, specify Style and give desired dimensions for or, and L. If otherwise special, furnish dimensioned sketch. or additional information call your local Parker ylinder Distributor. 0

16 Series Heavy Duty ir ylinders levis Mountings " to " Bore Sizes Table nvelope and Mounting Dimensions D dd Stroke Bore B -.00 NPT L L M M LB P. / / / / / / / / / / / /.0 / / / / / / / / / / /.0 / / / / / / / / / / / / /.0 / / / / / / / / / / / / /. / / / / / / / / / / / / /. / / / / / / / / / / / / /. / / / / / / / / / / / / /.00 / / / / / / / / / / / ushions not available on " bore. On ", /", " and /" bore sizes, the head-end (only) pipe thread is not full depth on cylinders with No. rods. Minimum of three full threads available. In " bore size model only, a single eye mounting, /" thick, is used. Dimension D (.") is hole diameter pin not supplied. Dimension D is pin diameter except in " bore. " bore head dimension is /" x /". See page B0. Table nvelope and Table od Dimensions Mounting Dimensions Thread od xtensions and Pilot Dimensions dd Stroke od Style Style od Dia. & -.00 Bore No. B D L N X XD Z ZD (Std.) / / -0 / - /. / / / / / / / / / / / / -0 / -0 /. / / / / / / / / / / / (Std.) / / -0 / -0 /. / / / / / / / / / / / / - / - /. / / / / / / / / / / (Std.) / / -0 / -0 /. / / / / / / / / / / / / / - - /. / / / / / / / / / / / - / - /. / / / / / / / / / / (Std.) / /-0 / -0 /. / / / / / / / / / / / / / - /-. / / / / / / / / / / / / - / - /. / / / / / / / / / / / /- - /. / / / / / / / / / / (Std.) / - /- /. / / / / / / / / / / / / / - / - /. / / / / / / / / / / / / /- - /. / / / / / / / / / / / / - /-. / / / / / / / / / / (Std.) / - / - /. / / / / / / / / / / / / /- / -. / / / / / / / / / / / / - - /. / / / / / / / / / / / / - / -. / / / / / / / / / / /- / - /. / / / / / / / / / / / (Std.) / - /- /. / / / / / / / / / / / / / - / - /. / / / / / / / / / /- - /. / / / / / / / / / / / - /-. / / / / / / / / / / / - / - /. / / / / / / / / / / / / /- / -. / / / / / / / / / / - /- /. / / / / / / / / / (Std.) / / - - /. / / / / / / / / / / / /- -. / / / / / / / / / 0 / / / - /-. / / / / / / / / / / 0 / / - / - /. / / / / / / / / / / 0 / / /- / -. / / / / / / / / / 0 / / - /- /. / / / / / / / / 0 / / / - / - /. / / / / / / / 0 / Note: Shaded areas indicate non-standard rod sizes that are available and made to order. or ylinder Division Plant Locations See Page II.

17 Tie od, Head Square and ap Square Mountings " Bore Size Series Heavy Duty ir ylinders Tie ods xtended Style TB (NP Style MX) Style TB (NP MX) Head Tie ods xtended, illustrated: Style T (NP MX), ap Tie ods xtended; and Style TD (NP MX), Both nds Tie ods xtended are also available. ll T styles can be dimensioned from Style TB drawing at right. ZB + STO P + STO LB + STO DD TT SQ. BB Head Square lange Style B (NP Style M) ZB + STO P + STO LB + STO T TT SQ. T B HOLS ap Square lange Style HB (NP Style M) Z + STO P + STO LB + STO T X + STO T B HOLS od nd Dimensions see table Thread Style Thread Style (NP Style SM) (NP Style IM) Small Male Intermediate Male D NH LTS L N B high strength rod end stud is supplied on thread style through " diameter rods and on thread style through /" diameter rods. Larger sizes or special rod ends are cut threads. Style rod ends are recommended where the workpiece is secured against the rod shoulder. hen the workpiece is not shouldered, style rod ends are D NH LTS L N B Thread Style (NP Style S) Small emale D NH LTS recommended through " piston rod diameters and style rod ends are recommended on larger diameters. Use style for applications where female rod end threads are required. If rod end is not specified, style will be supplied. N B Special Thread Style Special thread, extension, rod eye, blank, etc., are also available. To order, specify Style and give desired dimensions for or, and L. If otherwise special, furnish dimensional sketch. or additional information call your local Parker ylinder Distributor.

18 Series Heavy Duty ir ylinders Side Lug, Side Tapped, ap Trunnion, Head Trunnion, ap ixed levis Mountings " Bore Size Side Lug Style (NP Style MS) US ZB + STO P + STO LB + STO Side Tapped Style (NP Style MS) TT SQ. ZB + STO P + STO LB + STO ST S S TT SQ. TS SB S HOLS S S XS SU SS + STO SU S TN NT THD, ND DP TPPD MT. HOLS XT SN + STO ap Trunnion Style DB (NP Style MT) UT ZB + STO P + STO LB + STO Head Trunnion Style D (NP Style MT) UT ZB + STO P + STO LB + STO TD TD TL TT SQ. TL X + STO TL TT SQ. TL X ap ixed levis Style BB (NP Style MP) Z + STO P + STO LB + STO D PIOT PIN M L L M X + STO B Note: Other mounting styles and double rod end cylinders are available on request. onsult factory for details. Table nvelope and Mounting Dimensions dd Stroke Bore BB B D DD B L L M M ND NT SB ST SU S TD T TL TN TS US UT LB P SN SS / /.00 / /- / / / / / / / / / / /-0. / / /. / / / / 0 / 0 / / / / / Table od Dimensions Table nvelope and Mounting Dimensions Thread od xtensions and Pilot Dimensions dd Stroke od Style Style od Dia. & -.00 Bore No. B D L N TT X XS XT X X X ZB Z Z / / - - /. / / / / / / / / / / / / / / / / / / - / -. / / / / / / / / / / / / / / / / / - / - /. / / / / / / / / / / / / / / / or ylinder Division Plant Locations See Page II.

19 Tie od, Head Square and ap Square Mountings " to " Bore Size Series Heavy Duty ir ylinders Tie ods xtended Style TB (NP Style MX) Style TB (NP MX) Head Tie ods xtended, illustrated: Style T (NP MX), ap Tie ods xtended; and Style TD (NP MX), Both nds Tie ods xtended are also available. ll T styles can be dimensioned from Style TB drawing at right. ZB + STO P + STO LB + STO DD Mounting styles TB & TD not offered in " bore, rod codes #, and 0. TT SQ. BB Head Square lange Style B (NP Style M) ZB + STO P + STO LB + STO T TT SQ. T B HOLS ap Square lange Style HB (NP Style M) Z + STO P + STO LB + STO T X + STO T B HOLS od nd Dimensions see table Thread Style Thread Style (NP Style SM) (NP Style IM) Small Male Intermediate Male D NH LTS L N B D NH LTS high strength rod end stud is supplied on thread style through " diameter rods and on thread style through /" diameter rods. Larger sizes or special rod ends are cut threads. Style rod ends are recommended where the workpiece is secured against the rod shoulder. hen the workpiece is not shouldered, style rod ends are L N B Thread Style (NP Style S) Small emale D NH LTS recommended through " piston rod diameters and style rod ends are recommended on larger diameters. Use style for applications where female rod end threads are required. If rod end is not specified, style will be supplied. N B Special Thread Style Special thread, extension, rod eye, blank, etc., are also available. To order, specify Style and give desired dimensions for or, and L. If otherwise special, furnish dimensional sketch. or additional information call your local Parker ylinder Distributor.

20 Series Heavy Duty ir ylinders Tie od, Head Square and ap Square Mountings " to " Bore Size Table nvelope and Mounting Dimensions dd Stroke Bore BB DD B NPT T LB P. / / - / / / / / /.. / / 0. / / - 0 / / / / /..0 / /. / /- / / / / /.0.0 / /. / / - / / / / / / / 0.0. / / Table od Dimensions od Style Style od Dia. & -.00 Bore No. B D L N TT X ZB Z 0 (Std.) 0 (Std.) 0 (Std.) (Std.) / / / / / / / / / / / / / / / / / / / / - / - / - / - / - / - / - /- / - / - /- / - / - /- / - / - /- / - / - /- / - / - /- / - / - /- / - / - /- / - / - /- / - / - Thread - - / - / - / - / - / - - /- / - / - /- / - / - /- - / - /- - / - /- / - / - - / - / - - / - / - /- - / - /- - / / / / / / / / / / / / / / / / / / / / od xtensions and Pilot Dimensions / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Table nvelope and Mounting Dimensions / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / dd Stroke / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / 0 / 0 / 0 / 0 / 0 / 0 / 0 / or ylinder Division Plant Locations See Page II.

21 Side Lugs and enterline Lugs Mountings " to " Bore Size Side Lug Style (NP Style MS) US Series Heavy Duty ir ylinders ZB + STO P + STO LB + STO Ð.00 Ð.00 ST S S TT SQ. TS S S SB HOLS S XS SU SS + STO SU S enterline Lugs Style (NP Style MS) US ZB + STO P + STO LB + STO SB HOLS ST S S TT SQ. TS S S S XS SU SS + STO SU S od nd Dimensions see table Thread Style (NP Style SM) Small Male D NH LTS L N B Thread Style (NP Style IM) Intermediate Male high strength rod end stud is supplied on thread style through " diameter rods and on thread style through /" diameter rods. Larger sizes or special rod ends are cut threads. Style rod ends are recommended where the workpiece is secured against the rod shoulder. hen the workpiece is not shouldered, style rod ends are D NH LTS L N B Thread Style (NP Style S) Small emale D NH LTS N recommended through " piston rod diameters and style rod ends are recommended on larger diameters. Use style for applications where female rod end threads are required. If rod end is not specified, style will be supplied. B Special Thread Style Special thread, extension, rod eye, blank, etc., are also available. To order, specify Style and give desired dimensions for or, and L. If otherwise special, furnish dimensional sketch. or additional information call your local Parker ylinder Distributor.

22 Series Heavy Duty ir ylinders Table nvelope and Mounting Dimensions dd Stroke Bore NPT SB ST SU S TS US LB P SS / / / / / / / / / / / / / 0 0 / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Upper surface spotfaced for socket head screws. Side Lugs and enterline Lugs Mountings " to " Bore Sizes Table od Dimensions Table nvelope and Mounting Dimensions Thread od xtensions and Pilot Dimensions dd Stroke od Style Style od Dia. & -.00 Bore No. B D L N TT XS ZB (Std.) / / / /- /- /- /- - - /- /- / / /.... / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /- /-. / / / / / / / / /- /- /. / / / / / / / / 0 0 (Std.) 0 (Std.) / / / / / / / / /- /- /- /- /- /- /- /- /- /- /- /- /- /- /- /- /- - /- /- /- /- /- /- /- - /- /- - /- /- /- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /- /- /. / / / / / / / /- -. / / / / / / / / / (Std.) / / / / / / /- /- /- /- /- /- /- /- /- /- /- /- - /- /- /- - /- /- - / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / or ylinder Division Plant Locations See Page II.

23 Side Tapped and Side nd Lugs Mountings " to " Bore Size Series Heavy Duty ir ylinders Side Tapped Style (NP Style MS) TT SQ. ZB + STO P + STO LB + STO Ð.00 Ð.00 TN NT THD, ND DP TPPD MT. HOLS XT SN + STO Side nd Lugs Style (NP Style MS) ylinders with this mounting style are mounted on the precision ground surfaces of the head and cap. There must be a minimum gap of at least / of an inch between the bottom of the lug and the mounting surface before the mounting bolts are tightened. Z + STO X + STO P + STO LB + STO Ð.00 Ð.00 T S TT SQ. S B HOLS O L S + STO L O Not offered in the following sizes: " bore, rod codes #,,,, and 0; 0" bore, rod codes #, and 0; and bore, rod codes #, and. od nd Dimensions see table Thread Style (NP Style SM) Small Male D NH LTS L N B Thread Style (NP Style IM) Intermediate Male high strength rod end stud is supplied on thread style through " diameter rods and on thread style through /" diameter rods. Larger sizes or special rod ends are cut threads. Style rod ends are recommended where the workpiece is secured against the rod shoulder. hen the workpiece is not shouldered, style rod ends are D NH LTS L N B Thread Style (NP Style S) Small emale D NH LTS N recommended through " piston rod diameters and style rod ends are recommended on larger diameters. Use style for applications where female rod end threads are required. If rod end is not specified, style will be supplied. B Special Thread Style Special thread, extension, rod eye, blank, etc., are also available. To order, specify Style and give desired dimensions for or, and L. If otherwise special, furnish dimensional sketch. or additional information call your local Parker ylinder Distributor.

24 Series Heavy Duty ir ylinders Table nvelope and Mounting Dimensions Side Tapped and Side nd Lugs Mountings " to " Bore Sizes dd Stroke Bore B NPT L O S T ND NT TN LB P S SN 0 / 0 / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /- 0.0 / / / / / Table od Dimensions Table nvelope and Mounting Dimensions Thread od xtensions and Pilot Dimensions dd Stroke od Style Style od Dia. & -.00 Bore No. B D L N TT XT X ZB Z (Std.) / / / /- /- /- /- - - /- /- / / /.... / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /- /-. / / / / / / / / / / /- /- /. / / / / / / / / 0 0 (Std.) 0 (Std.) / / / / / / / / /- /- /- /- /- /- /- /- /- /- /- /- /- /- /- /- /- - /- /- /- /- /- /- /- - /- /- - /- /- /- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / 0 / 0 / 0 / / / / / / / / / / / / / / / / / 0 / 0 / 0 / 0 / 0 / 0 / 0 / / / / /- /- /. / / / / / / 0 / / / /- -. / / / / / / / / 0 / / / (Std.) / / / / / / /- /- /- /- /- /- /- /- /- /- /- /- - /- /- /- - /- /- - / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Mounting style not offered in this rod size. aution: hen using mounting style, check clearance between mounting members and rod attachment or accessory. If necessary, specify longer rod extension to avoid interference with mounting members. or ylinder Division Plant Locations See Page II.

25 Side nd ngle and levis Mountings " to " Bore Sizes Series Heavy Duty ir ylinders Side nd ngles Style B (NP Style MS) Z + STO X + STO P + STO LB + STO T B HOLS S T H TT SQ. O L S + STO L O Not offered in the following sizes: " bore, rod codes #,,,, and 0; 0" bore, rod codes #, and 0. ap ixed levis Style BB (NP Style MP) Z + STO P + STO LB + STO D PIOT PIN M L X + STO L M B od nd Dimensions see table Thread Style (NP Style SM) Small Male D NH LTS L N B Thread Style (NP Style IM) Intermediate Male high strength rod end stud is supplied on thread style through " diameter rods and on thread style through /" diameter rods. Larger sizes or special rod ends are cut threads. Style rod ends are recommended where the workpiece is secured against the rod shoulder. hen the workpiece is not shouldered, style rod ends are D NH LTS L N B Thread Style (NP Style S) Small emale D NH LTS N recommended through " piston rod diameters and style rod ends are recommended on larger diameters. Use style for applications where female rod end threads are required. If rod end is not specified, style will be supplied. B Special Thread Style Special thread, extension, rod eye, blank, etc., are also available. To order, specify Style and give desired dimensions for or, and L. If otherwise special, furnish dimensional sketch. or additional information call your local Parker ylinder Distributor. 0

26 Series Heavy Duty ir ylinders Table nvelope and Mounting Dimensions D dd Stroke Bore B H L O T B -.00 NPT L L M M S LB P S / / / / / /.00 / / / / / / / / / / / / / 0 / / / / /. 0 / / / / / / / / / / / 0 / / / / / / /. / / / / / / / / / / / / / / / / / /.00 / / / / / / / / / / / / / D is pin diameter. Side nd ngles and levis Mountings " to " Bore Sizes Table od Dimensions Thread od xtensions and Pilot Dimensions Table nvelope and Mounting Dimensions dd Stroke od Style Style od Dia. & -.00 Bore No. B D L N TT X X Z Z (Std.) / / / /- /- /- /- - - /- /- / / /.... / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /- /-. / / / / / / / / / / /- /- /. / / / / / / / / 0 0 (Std.) 0 (Std.) / / / / / / / / /- /- /- /- /- /- /- /- /- /- /- /- /- /- /- /- /- - /- /- /- /- /- /- /- - /- /- - /- /- /- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / 0 / 0 / 0 / 0 / 0 / 0 / / / / / / / 0 / 0 / 0 / 0 / 0 / 0 / 0 / 0 / 0 / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /- /- /. / / / / / / / / / /- -. / / / / / / / / / / / (Std.) / / / / / / /- /- /- /- /- /- /- /- /- /- /- /- - /- /- /- - /- /- - / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Mounting style not offered in this rod size. aution: hen using mounting style, check clearance between mounting members and rod attachment or accessory. If necessary, specify longer rod extension to avoid interference with mounting members. or ylinder Division Plant Locations See Page II.

27 Trunnion Mountings " to " Bore Sizes Series Heavy Duty ir ylinders Head Trunnion Style D (NP Style MT) UT ZB + STO P + STO LB + STO TD TL TT SQ. TL X ap Trunnion Style DB (NP Style MT) UT ZB + STO P + STO LB + STO TD TL TT SQ. TL X + STO Intermediate ixed Trunnion Style DD (NP Style MT) UM ZB + STO P + STO LB + STO BD U TD TL TT SQ. TM TL XI od nd Dimensions see table Thread Style (NP Style SM) Small Male D NH LTS L N B Thread Style (NP Style IM) Intermediate Male high strength rod end stud is supplied on thread style through " diameter rods and on thread style through /" diameter rods. Larger sizes or special rod ends are cut threads. Style rod ends are recommended where the workpiece is secured against the rod shoulder. hen the workpiece is not shouldered, style rod ends are D NH LTS L N B Thread Style (NP Style S) Small emale D NH LTS N recommended through " piston rod diameters and style rod ends are recommended on larger diameters. Use style for applications where female rod end threads are required. If rod end is not specified, style will be supplied. B Special Thread Style Special thread, extension, rod eye, blank, etc., are also available. To order, specify Style and give desired dimensions for or, and L. If otherwise special, furnish dimensional sketch. or additional information call your local Parker ylinder Distributor.

28 Series Heavy Duty ir ylinders Table nvelope and Mounting Dimensions dd Stroke Style TD DD Min. Bore BD NPT -.00 TL TM UM UT U LB P Stroke / / / / / /. / / / / / / / / 0 0 / / / /.0 / / / / / / / / / / /.0 / / / / / / / / / / / / / /.000 / 0 / / / / / Trunnion Mountings " to " Bore Sizes Table od Dimensions Thread od xtensions and Pilot Dimensions Table nvelope and Mounting Dimensions dd Stroke od Style Style od Dia. & -.00 Min. Bore No. B D L N TT X XI X ZB (Std.) / / / /- /- /- /- - - /- /- / / /.... / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /- /-. / / / / / / / / / / /- /- /. / / / / / / / / / / 0 0 (Std.) 0 (Std.) / / / / / / / / /- /- /- /- /- /- /- /- /- /- /- /- /- /- /- /- /- - /- /- /- /- /- /- /- - /- /- - /- /- /- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /- /- /. / / / / / / / / / /- -. / / / / / / / / / / / (Std.) / / / / / / /- /- /- /- /- /- /- /- /- /- /- /- - /- /- /- - /- /- - / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Dimension XI to be specified by customer. or ylinder Division Plant Locations See Page II.

29 Spherical Bearing Mounting Style SB /" to " Bore Sizes Series Heavy Duty ir ylinders LUBITION ITTIN XL + STO Z + STO X + STO M LUBITION ITTIN MS D D X L N X Thread dd Stroke od Style Style od Dia. Bore No. X XL Z D X L M MS N / / / (Std.) (Std.) (Std.) (Std.) (Std.) (Std.) (Std.) / / / / / / / / / / / / / / / / / / / /-0 /-0 /-0 /- /- /- - /-0 /-0 /-0 /-0 /-0 /-0 /- /- /- /- /- /- /- /- /- /- /- /- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / 0 0 / 0 / 0 / 0 / 0 / 0 / / / / / / / / / / / / / / / / / / / / / / / / 0 / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Maximum operating pressure at : design factor is based on tensile strength of material. Pressure ratings are based on standard commercial bearing ratings. Note: or additional dimensions see Series, page 0. Dimension D is hole diameter. orresponding rod eye pin diameter may not match pin diameter of cap. od No. is standard. / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Max. Oper. PSI or additional information call your local Parker ylinder Distributor.