T4 series. 4 A Triacs. Features. Applications. Description. Table 1. Main characteristics. Table 2. Device summary

Transcription

1 4 A Triacs Datasheet production data. Table 1. Main characteristics Symbol Value Unit I T(rms) 4 A V DRM, V RRM 600 to 800 V I GT 5 to 35 ma Features Three quadrants Triac 600 to 800 V V DRM /V RRM Applications General purpose AC inductive loads Motor control circuits Small home appliances Description Based on ST s Snubberless / Logic level technology providing high commutation performances, the T4 series is suitable for use on AC inductive loads. They are recommended for applications using universal motors, electro valves, kitchen aid equipments, power tools, dishwashers. Table 2. Device summary Symbol Marking T405-xxxB T405-xxxB-TR T405-xxxH T405-xxxT T410-xxxB T410-xxxB-TR see Table 11 T410-xxxH T410-xxxT T435-xxxB T435-xxxB-TR T435-xxxH T435-xxxT xxx = Voltage: 600 V, 700 V or 800 V (see Table 10). April 2016 DocID7699 Rev 7 1/15 This is information on a product in full production. 15

2 Characteristics T4 series 1 Characteristics Table 3. Absolute maximum ratings (T j = 25 C unless otherwise stated) Symbol Parameter Value Unit I T(rms) I TSM On-state rms current (full sine wave) Non repetitive surge peak on-state current (full cycle, T j initial = 25 C) IPAK, DPAK, TO-220AB T c = 110 C 4 A F = 50 Hz t = 20 ms 30 F = 60 Hz t = 16.7 ms 31 I ² t I ² t value for fusing t p = 10 ms 5.1 A ² s di/dt Critical rate of rise of on-state current I G = 2 x I GT, t r 100 ns F = 120 Hz T j = 125 C 50 A/µs I GM Peak gate current t p = 20 µs T j = 125 C 4 A P G(AV) Average gate power dissipation T j = 125 C 1 W T stg T j Storage junction temperature range Operating junction temperature range - 40 to to A C Table 4. Electrical characteristics (T j = 25 C, unless otherwise stated) Symbol Test conditions Quadrant Value T405 T410 T435 Unit I GT (1) V D = 12 V, R L = 30 Ω I - II - III Max ma V GT V D = 12 V, R L = 30 Ω I - II - III Max. 1.3 V V GD V D = V DRM, R L = 3.3 k Ω, T j = 125 C I - II - III Min. 0.2 V (2) I H I T = 100 ma Max ma I - III Max I L I G = 1.2 I GT II Max ma dv/dt (2) V D = 67% V DRM, gate open T j = 125 C Min V/µs (dv/dt)c = 0.1 V/µs (di/dt)c (2) (dv/dt)c = 10 V/µs T j = 125 C Min A/ms (without snubber) Minimum I GT is guaranteed at 5% of I GT max. 2. For both polarities of A2 referenced to A1 2/15 DocID7699 Rev 7

3 Characteristics Table 5. Static characteristics Symbol Test conditions Value Unit V (1) TM (1) V t0 (1) R d I DRM I RRM I TM = 8.5 A, t p = 380 µs T j = 25 C Max V Threshold voltage T j = 125 C Max V Dynamic resistance T j = 125 C Max. 120 m V DRM = V RRM T j = 25 C 5 µa Max. T j = 125 C 1 ma 1. For both polarities of A2 referenced to A1 Table 6. Thermal resistance Symbol Parameter Value Unit R th(j-c) Junction to case (AC) IPAK, DPAK,TO-220AB 2.6 C/W R th(j-a) Junction to ambient (DC) Junction to ambient (DC) S = 0.5 cm² DPAK 70 C/W TO-220AB 60 IPAK S = Copper surface under tab. DocID7699 Rev 7 3/15

4 Characteristics T4 series Figure 1. Maximum power dissipation versus RMS on-state current (full cycle) Figure 2. RMS on-state current versus case temperature (full cycle) 6 P(W) I T(RMS) (A) Figure 3. RMS on-state current versus ambient temperature (printed circuit board FR4, copper thickness: 35µm) (full cycle) Figure 4. Relative variation of thermal impedance versus pulse duration I T(RMS) (A) T ( C) C DPAK 2 (S=0.5CM ) Figure 5. On-state characteristics (maximum values) Figure 6. Surge peak on-state current versus number of cycles I TM(A) Tj max. V to = 0.90V R d = 120 mω I TSM(A) t=20ms One cycle 1.0 T= j Tj max. T j = 25 C Repetitive T C=110 C Non repetitive Tj initial=25 C V TM(V) Number of cycles /15 DocID7699 Rev 7

5 Characteristics Figure 7. Non-repetitive surge peak on-state current for a sinusoidal pulse with width t p < 10 ms Figure 8. Relative variation of gate trigger current, holding current and latching current versus junction temperature (typical values) 2.5 I GT,I H,I L[T] j / I GT,I H,I L[T j=25 C] 2.0 IGT IH & IL 0.5 T j( C) Figure 9. Relative variation of critical rate of decrease of main current versus (dv/dt)c (typical values) Figure 10. Relative variation of critical rate of decrease of main current versus junction temperature (di/dt)c [(dv/dt)c] / Specified (di/dt)c T T T (dv/dt)c (V/µs) (di/dt)c [T j ] / (di/dt)c [T j specified] T j( C) Figure 11. DPAK thermal resistance junction to ambient versus copper surface under tab (printed circuit board FR4, copper thickness: 35 µm) R th(j-a) ( C/W) S(cm²) DocID7699 Rev 7 5/15

6 Package information T4 series 2 Package information Epoxy meets UL94, V0 Lead-free package Recommended torque: 0.4 to 0.6 N m In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: ECOPACK is an ST trademark. 2.1 DPAK package information Figure 12. DPAK package outline Note: This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed. 6/15 DocID7699 Rev 7

7 Package information Table 7. DPAK package mechanical data Dimensions Ref. Millimeters Inches (1) Min. Typ. Max. Min. Typ. Max. A A A b b c c D D E E e e H L L L V Inch dimensions are only for reference Figure 13. Footprint (dimensions in mm) DocID7699 Rev 7 7/15

8 Package information T4 series 2.2 IPAK package information Figure 14. IPAK package outline Note: This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed. 8/15 DocID7699 Rev 7

9 Package information Table 8. IPAK package mechanical data Dimensions Ref. Millimeters Inches (1) Min. Typ. Max. Min. Typ. Max. A A b b b c c D E e e H L L L V Inch dimensions are only for reference DocID7699 Rev 7 9/15

10 Package information T4 series 2.3 TO-220AB (insulated and non-insulated) information Figure 15. TO-220AB (insulated and non-insulated) package outline 10/15 DocID7699 Rev 7

11 Package information Table 9. TO-220AB (insulated and non-insulated) package mechanical data Dimensions Ref. Millimeters Inches (1) Min. Typ. Max. Min. Typ. Max. A a a B b b C c c e F ØI I L l l M Inch dimensions are only for reference DocID7699 Rev 7 11/15

12 Ordering information T4 series 3 Ordering information Figure 16. Order information scheme Table 10. Product selector Part Number Voltage (xxx) 600 V 700 V 800 V Sensitivity Type Package T405-xxxB X 5 ma Logic level DPAK T405-xxxB-TR X X X 5 ma Logic level DPAK T405-xxxH X X 5 ma Logic level IPAK T405-xxxT X 5 ma Logic level TO-220AB T410-xxxB X 10 ma Logic Level DPAK T410-xxxB-TR X X 10 ma Logic Level DPAK T410-xxxH X X 10 ma Logic Level IPAK T410-xxxT X X X 10 ma Logic Level TO-220AB T435-xxxB X 35 ma Snubberless DPAK T435-xxxB-TR X X X 35 ma Snubberless DPAK T435-xxxH X X 35 ma Snubberless IPAK T435-xxxT X X 35 ma Snubberless TO-220AB Blank = Unavailable 12/15 DocID7699 Rev 7

13 Ordering information Table 11. Ordering information Order code Marking Package Weight Base qty. Delivery mode T B T T B T T B T T B-TR T T B-TR T T B-TR T T B-TR T T B-TR T T B-TR T T B-TR T T B-TR T T H T T H T T H T T H T T H T T H T T T T T T T T T T T T T T T T T T T T T T T T T 75 Tube DPAK 0.3 g 2500 Tape and reel IPAK Tube TO-220AB DocID7699 Rev 7 13/15

14 Revision history T4 series 4 Revision history Table 12. Document revision history Date Revision Changes Jun Last updated. 25-Mar Layout updated0 No content change. 25-Jan Markings changed in Table May Updated DPAK and IPAK package information and reformatted to current standard. 11-Feb Updated package silhouettes in cover page. 1-Apr Removed ISOWATT-220AB package information. 14/15 DocID7699 Rev 7

15 IMPORTANT NOTICE PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document STMicroelectronics All rights reserved DocID7699 Rev 7 15/15