L78L. Positive voltage regulators. Description. Features
|
|
|
- Amanda Doyle
- 7 years ago
- Views:
Transcription
1 Positive voltage regulators Datasheet - production data Features Output current up to 100 ma Output voltages of 3.3; 5; 6; 8; 9; 10; 12; 15; 18; 24 V thermal overload protection Short-circuit protection No external components are required Available in either ± 4% (A) or ± 8% (C) selection Description The L78L series of three-terminal positive regulators employ internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 ma output current. They are intended as fixed voltage regulators in a wide range of applications including local or oncard regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power pass elements to make high-current voltage regulators. The L78L series used as Zener diode/resistor combination replacement, offers e improvement along with lower quiescent current and lower noise. June 2016 DocID2145 Rev 26 1/45 This is information on a product in full production.
2 Contents L78L Contents 1 Diagram Pin configuration Maximum ratings Electrical characteristics Typical performance Typical application Package information TO-92 package information TO-92 packing information TO-92 Ammopak packing information SO-8 package information SO-8 packing information SOT-89 package information SOT-89 packing information Ordering information Revision history /45 DocID2145 Rev 26
3 Diagram 1 Diagram Figure 1: Schematic diagram DocID2145 Rev 26 3/45
4 Pin configuration L78L 2 Pin configuration Figure 2: Pin connection (top view, bottom view for TO-92) Figure 3: Test circuits 4/45 DocID2145 Rev 26
5 Maximum ratings 3 Maximum ratings Table 1: Absolute maximum ratings Symbol Parameter Value Unit VI DC Input voltage VO = 3.3 to 9 V 30 VO = 12 to 15 V 35 VO = 18 to 24 V 40 IO Output current 100 ma PD Power dissipation Internally limited (1) mw TSTG Storage temperature range -65 to 150 C TOP Notes: Operating junction temperature range for L78LxxAC / L78LxxC 0 to 125 for L78LxxAB -40 to 125 (1) Our SO-8 package used for voltage regulators is modified internally to have pins 2, 3, 6 and 7 electrically communed to the die attach flag. This particular frame decreases the total thermal resistance of the package and increases its ability to dissipate power when an appropriate area of copper on the printed circuit board is available for heat-sinking. The external dimensions are the same as for the standard SO-8. V C Table 2: Thermal data Symbol Parameter SO-8 TO-92 SOT-89 Unit RthJC Thermal resistance junction-case (max) C/W RthJA Thermal resistance junction-ambient (max) 55 (1) (1) C/W Notes: (1) Considering 6 cm² of copper Board heat-sink. DocID2145 Rev 26 5/45
6 Electrical characteristics L78L 4 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 8.3 V, IO = 40 ma, CI = 0.33 µf, CO = 0.1 µf unless otherwise specified. Table 3: Electrical characteristics of L78L33C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Id Id Output voltage Line regulation Load regulation Quiescent current Quiescent current change IO = 1 to 40 ma, VI = 5.3 to 20 V IO = 1 to 70 ma, VI = 8.3 V VI = 5.4 to 20 V, TJ = 25 C 150 VI = 6.3 to 20 V, TJ = 25 C 100 IO = 1 to 100 ma, TJ = 25 C 60 IO = 1 to 40 ma, TJ = 25 C 30 TJ = 25 C 6 ma TJ = 125 C 5.5 ma IO = 1 to 40 ma 0.2 VI = 6.3 to 20 V 1.5 en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 40 µv SVR Supply voltage rejection VI = 6.3 to 16.3 V, f = 120 Hz IO = 40 ma, TJ = 25 C V ma db Vd Dropout voltage 2 V 6/45 DocID2145 Rev 26
7 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 10 V, IO = 40 ma, CI = 0.33 µf, CO = 0.1 µf unless otherwise specified. Table 4: Electrical characteristics of L78L05C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 7 to 20 V IO = 1 to 70 ma, VI = 10 V V Line regulation VI = 8.5 to 20 V, TJ = 25 C 200 VI = 9 to 20 V, TJ = 25 C 150 Load regulation IO = 1 to 100 ma, TJ = 25 C 60 IO = 1 to 40 ma, TJ = 25 C 30 Id Quiescent current TJ = 25 C 6 ma TJ = 125 C 5.5 ma Id Quiescent current change IO = 1 to 40 ma 0.2 VI = 8 to 20 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 40 µv SVR Supply voltage rejection VI = 9 to 20 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 2 V DocID2145 Rev 26 7/45
8 Electrical characteristics L78L Refer to the test circuits, TJ = 0 to 125 C,VI = 14 V, IO = 40 ma, CI = 0.33 µf, CO = 0.1 µf unless otherwise specified. Table 5: Electrical characteristics of L78L08C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 8.5 to 20 V IO = 1 to 70 ma, VI = 12 V V Line regulation VI = 10.5 to 20 V, TJ = 25 C 200 VI = 11 to 20 V, TJ = 25 C 150 Load regulation IO = 1 to 100 ma, TJ = 25 C 80 IO = 1 to 40 ma, TJ = 25 C 40 Id Quiescent current TJ = 25 C 6 ma TJ = 125 C 5.5 ma Id Quiescent current change IO = 1 to 40 ma 0.2 VI = 8 to 20 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 60 µv SVR Supply voltage rejection VI = 9 to 20 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V 8/45 DocID2145 Rev 26
9 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 15 V, IO = 40 ma, CI = 0.33 µf, CO = 0.1 µf unless otherwise specified. Table 6: Electrical characteristics of L78L09C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 11.5 to 23 V IO = 1 to 70 ma, VI = 15 V V Line regulation VI = 11.5 to 23 V, TJ = 25 C 250 VI = 12 to 23 V, TJ = 25 C 200 Load regulation IO = 1 to 100 ma, TJ = 25 C 80 IO = 1 to 40 ma, TJ = 25 C 40 Id Quiescent current TJ = 25 C 6 ma TJ = 125 C 5.5 ma Id Quiescent current change IO = 1 to 40 ma 0.2 VI = 12 to 23 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 70 µv SVR Supply voltage rejection VI = 12 to 23 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V DocID2145 Rev 26 9/45
10 Electrical characteristics L78L Refer to the test circuits, TJ = 0 to 125 C, VI = 16 V, IO = 40 ma, CI = 0.33 µf, CO = 0.1 µf unless otherwise specified. Table 7: Electrical characteristics of L78L10C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 12.5 to 23 V 9 11 IO = 1 to 70 ma, VI = 16 V 9 11 V Line regulation VI = 12.5 to 23 V, TJ = 25 C 230 VI = 13 to 23 V, TJ = 25 C 170 Load regulation IO = 1 to 100 ma, TJ = 25 C 80 IO = 1 to 40 ma, TJ = 25 C 40 Id Quiescent current TJ = 25 C 6 ma TJ = 125 C 5.5 ma Id Quiescent current change IO = 1 to 40 ma 0.1 VI = 13 to 23 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 60 µv SVR Supply voltage rejection VI = 14 to 23 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V 10/45 DocID2145 Rev 26
11 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 19 V, IO = 40 ma, CI = 0.33 µf, CO = 0.1 µf unless otherwise specified. Table 8: Electrical characteristics of L78L12C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 14.5 to 27 V IO = 1 to 70 ma, VI = 19 V V Line regulation VI = 14.5 to 27 V, TJ = 25 C 250 VI = 16 to 27 V, TJ = 25 C 200 Load regulation IO = 1 to 100 ma, TJ = 25 C 100 IO = 1 to 40 ma, TJ = 25 C 50 Id Quiescent current TJ = 25 C 6.5 ma TJ = 125 C 6 ma Id Quiescent current change IO = 1 to 40 ma 0.2 VI = 16 to 27 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 80 µv SVR Supply voltage rejection VI = 15 to 25 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V DocID2145 Rev 26 11/45
12 Electrical characteristics L78L Refer to the test circuits, TJ = 0 to 125 C, VI = 23 V, IO = 40 ma, CI = 0.33 µf, CO = 0.1 µf unless otherwise specified Table 9: Electrical characteristics of L78L15C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 17.5 to 30 V IO = 1 to 70 ma, VI = 23 V V Line regulation VI = 17.5 to 30 V, TJ = 25 C 300 VI = 20 to 30 V, TJ = 25 C 250 Load regulation IO = 1 to 100 ma, TJ = 25 C 150 IO = 1 to 40 ma, TJ = 25 C 75 Id Quiescent current TJ = 25 C 6.5 ma TJ = 125 C 6 ma Id Quiescent current change IO = 1 to 40 ma 0.2 VI = 20 to 30 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 90 µv SVR Supply voltage rejection VI = 18.5 to 28.5 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V 12/45 DocID2145 Rev 26
13 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 27 V, IO = 40 ma, CI = 0.33 µf, CO = 0.1 µf unless otherwise specified. Table 10: Electrical characteristics of L78L18C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 22 to 33 V IO = 1 to 70 ma, VI = 27 V V Line regulation VI = 22 to 33 V, TJ = 25 C 320 VI = 22 to 33 V, TJ = 25 C 270 Load regulation IO = 1 to 100 ma, TJ = 25 C 170 IO = 1 to 40 ma, TJ = 25 C 85 Id Quiescent current TJ = 25 C 6.5 ma TJ = 125 C 6 ma Id Quiescent current change IO = 1 to 40 ma 0.2 VI = 23 to 33 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 120 µv SVR Supply voltage rejection VI = 23 to 33 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V DocID2145 Rev 26 13/45
14 Electrical characteristics L78L Refer to the test circuits, TJ = 0 to 125 C, VI = 33 V, IO = 40 ma, CI = 0.33 µf, CO = 0.1 µf unless otherwise specified. Table 11: Electrical characteristics of L78L24C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 27 to 38 V IO = 1 to 70 ma, VI = 33 V V Line regulation VI = 27 to 38 V, TJ = 25 C 350 VI = 28 to 38 V, TJ = 25 C 300 Load regulation IO = 1 to 100 ma, TJ = 25 C 200 IO = 1 to 40 ma, TJ = 25 C 100 Id Quiescent current TJ = 25 C 6.5 ma TJ = 125 C 6 ma Id Quiescent current change IO = 1 to 40 ma 0.2 VI = 28 to 38 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 200 µv SVR Supply voltage rejection VI = 29 to 35 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V 14/45 DocID2145 Rev 26
15 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C (AC) TJ = -40 to 125 C (AB),VI = 8.3 V, IO = 40mA, CI = 0.33 μf, CO = 0.1 μf unless otherwise specified. Table 12: Electrical characteristics of L78L33AB and L78L33AC Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 5.3 to 20 V IO = 1 to 70 ma, VI = 8.3 V V Line regulation VI = 5.4 to 20 V, TJ = 25 C 150 VI = 6.3 to 20 V, TJ = 25 C 100 Load regulation IO = 1 to 100 ma, TJ = 25 C 60 IO = 1 to 40 ma, TJ = 25 C 30 Id Quiescent current TJ = 25 C 6 ma TJ = 125 C 5.5 ma Id Quiescent current change IO = 1 to 40 ma 0.1 VI = 6.3 to 20 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 40 µv SVR Supply voltage rejection VI = 6.3 to 16.3 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 2 V DocID2145 Rev 26 15/45
16 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C (AC) TJ = -40 to 125 C (AB), VI = 10 V, L78L IO = 40 ma, CI = 0.33 μf, CO = 0.1 μf unless otherwise specified. Table 13: Electrical characteristics of L78L05AB and L78L05AC Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 7 to 20 V IO = 1 to 70 ma, VI = 10 V V Line regulation VI = 7.3 to 20 V, TJ = 25 C 150 VI = 8 to 20 V, TJ = 25 C 100 Load regulation IO = 1 to 100 ma, TJ = 25 C 60 IO = 1 to 40 ma, TJ = 25 C 30 Id Quiescent current TJ = 25 C 6 ma TJ = 125 C 5.5 ma Id Quiescent current change IO = 1 to 40 ma 0.1 VI = 8 to 20 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 40 µv SVR Supply voltage rejection VI = 8 to 18 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 2 V 16/45 DocID2145 Rev 26
17 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C (AC) TJ = -40 to 125 C (AB), VI = 12 V, IO = 40 ma, CI = 0.33 μf, CO = 0.1 μf unless otherwise specified. Table 14: Electrical characteristics of L78L06AB and L78L06AC Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 8.5 to 20 V IO = 1 to 70 ma, VI = 12 V V Line regulation VI = 8.5 to 20 V, TJ = 25 C 150 VI = 9 to 20 V, TJ = 25 C 100 Load regulation IO = 1 to 100 ma, TJ = 25 C 60 IO = 1 to 40 ma, TJ = 25 C 30 Id Quiescent current TJ = 25 C 6 ma TJ = 125 C 5.5 ma Id Quiescent current change IO = 1 to 40 ma 0.1 VI = 9 to 20 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 50 µv SVR Supply voltage rejection VI = 9 to 20 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V DocID2145 Rev 26 17/45
18 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C (AC) TJ = -40 to 125 C (AB), VI = 14 V, L78L IO = 40 ma, CI = 0.33 μf, CO = 0.1 μf unless otherwise specified. Table 15: Electrical characteristics of L78L08AB and L78L08AC Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 10.5 to 23 V IO = 1 to 70 ma, VI = 14 V V Line regulation VI = 10.5 to 23 V, TJ = 25 C 175 VI = 11 to 23 V, TJ = 25 C 125 Load regulation IO = 1 to 100 ma, TJ = 25 C 80 IO = 1 to 40 ma, TJ = 25 C 40 Id Quiescent current TJ = 25 C 6 ma TJ = 125 C 5.5 ma Id Quiescent current change IO = 1 to 40 ma 0.1 VI = 11 to 23 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 60 µv SVR Supply voltage rejection VI = 12 to 23 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V 18/45 DocID2145 Rev 26
19 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C (AC) TJ = -40 to 125 C (AB), VI =15 V, IO= 40 ma, CI = 0.33 μf, CO = 0.1 μf unless otherwise specified. Table 16: Electrical characteristics of L78L09AB and L78L09AC Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 11.5 to 23 V IO = 1 to 70 ma, VI = 15 V V Line regulation VI = 11.5 to 23 V, TJ = 25 C 225 VI = 12 to 23 V, TJ = 25 C 150 Load regulation IO = 1 to 100 ma, TJ = 25 C 80 IO = 1 to 40 ma, TJ = 25 C 40 Id Quiescent current TJ = 25 C 6 ma TJ = 125 C 5.5 ma Id Quiescent current change IO = 1 to 40 ma 0.1 VI = 12 to 23 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 70 µv SVR Supply voltage rejection VI = 12 to 23 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V DocID2145 Rev 26 19/45
20 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C (AC) TJ = -40 to 125 C (AB), VI= 16 V, L78L IO = 40mA, CI = 0.33 μf, CO = 0.1 μf unless otherwise specified. Table 17: Electrical characteristics of L78L10AC Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 12.5 to 23 V IO = 1 to 70 ma, VI = 16 V V Line regulation VI = 12.5 to 23 V, TJ = 25 C 230 VI = 13 to 23 V, TJ = 25 C 170 Load regulation IO = 1 to 100 ma, TJ = 25 C 80 IO = 1 to 40 ma, TJ = 25 C 40 Id Quiescent current TJ = 25 C 6 ma TJ = 125 C 5.5 ma Id Quiescent current change IO = 1 to 40 ma 0.1 VI = 13 to 23 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 60 µv SVR Supply voltage rejection VI = 14 to 23 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V 20/45 DocID2145 Rev 26
21 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C (AC) TJ = -40 to 125 C (AB), VI =19 V, IO = 40 ma, CI = 0.33 μf, CO = 0.1 μf unless otherwise specified. Table 18: Electrical characteristics of L78L12AB and L78L12AC Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 14.5 to 27 V IO = 1 to 70 ma, VI = 19 V V Line regulation VI = 14.5 to 27 V, TJ = 25 C 250 VI = 16 to 27 V, TJ = 25 C 200 Load regulation IO = 1 to 100 ma, TJ = 25 C 100 IO = 1 to 40 ma, TJ = 25 C 50 Id Quiescent current TJ = 25 C 6.5 ma TJ = 125 C 6 ma Id Quiescent current change IO = 1 to 40 ma 0.1 VI = 16 to 27 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 80 µv SVR Supply voltage rejection VI = 15 to 25 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V DocID2145 Rev 26 21/45
22 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C (AC) TJ = -40 to 125 C (AB),VI = 23 V, L78L IO= 40 ma, CI = 0.33 μf, CO = 0.1 μf unless otherwise specified. Table 19: Electrical characteristics of L78L15AB and L78L15AC Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 17.5 to 30 V IO = 1 to 70 ma, VI = 23 V V Line regulation VI = 17.5 to 30 V, TJ = 25 C 300 VI = 20 to 30 V, TJ = 25 C 250 Load regulation IO = 1 to 100 ma, TJ = 25 C 150 IO = 1 to 40 ma, TJ = 25 C 75 Id Quiescent current TJ = 25 C 6.5 ma TJ = 125 C 6 ma Id Quiescent current change IO = 1 to 40 ma 0.1 VI = 20 to 30 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 90 µv SVR Supply voltage rejection VI = 18.5 to 28.5 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V 22/45 DocID2145 Rev 26
23 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C (AC) TJ = -40 to 125 C (AB),VI = 27 V, IO = 40 ma, CI = 0.33 μf, CO = 0.1 μf unless otherwise specified. Table 20: Electrical characteristics of L78L18AC Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 22 to 33 V IO = 1 to 70 ma, VI = 27 V V Line regulation VI = 22 to 33 V, TJ = 25 C 320 VI = 22 to 33 V, TJ = 25 C 270 Load regulation IO = 1 to 100 ma, TJ = 25 C 170 IO = 1 to 40 ma, TJ = 25 C 85 Id Quiescent current TJ = 25 C 6.5 ma TJ = 125 C 6 ma Id Quiescent current change IO = 1 to 40 ma 0.1 VI = 23 to 33 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 120 µv SVR Supply voltage rejection VI = 23 to 33 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V DocID2145 Rev 26 23/45
24 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C (AC) TJ = -40 to 125 C (AB),VI = 33 V, L78L IO = 40 ma, CI = 0.33 μf, CO = 0.1 μf unless otherwise specified. Table 21: Electrical characteristics of L78L24AB and L78L24AC Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C V VO Output voltage IO = 1 to 40 ma, VI = 27 to 38 V IO = 1 to 70 ma, VI = 33 V V Line regulation VI = 27 to 38 V, TJ = 25 C 350 VI = 28 to 38 V, TJ = 25 C 300 Load regulation IO = 1 to 100 ma, TJ = 25 C 200 IO = 1 to 40 ma, TJ = 25 C 100 Id Quiescent current TJ = 25 C 6.5 ma TJ = 125 C 6 ma Id Quiescent current change IO = 1 to 40 ma 0.1 VI = 28 to 38 V 1.5 ma en Output noise voltage B = 10 Hz to 100 khz, TJ = 25 C 200 µv5y SVR Supply voltage rejection VI = 29 to 33 V, f = 120 Hz IO = 40 ma, TJ = 25 C db Vd Dropout voltage 1.7 V 24/45 DocID2145 Rev 26
25 Typical performance 5 Typical performance Figure 4: L78L05/12 output voltage vs. ambient temperature Figure 5: L78L05/12/24 load characteristics Figure 6: L78L05/12/24 thermal shutdown Figure 7: L78L05/12 quiescent current vs. output current DocID2145 Rev 26 25/45
26 Typical performance Figure 8: L78L05 quiescent current vs. input voltage Figure 9: L78L05/12/24 output characteristics L78L Figure 10: L78L05/12/24 ripple rejection Figure 11: L78L05 dropout characteristics Figure 12: L78L short-circuit output current 26/45 DocID2145 Rev 26
27 Typical application 6 Typical application Figure 13: High output current short-circuit protected Figure 14: Outuput boost circuit Figure 15: Current regulator DocID2145 Rev 26 27/45
28 Typical application Figure 16: Adjustable output regulator L78L 28/45 DocID2145 Rev 26
29 Package information 7 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: ECOPACK is an ST trademark. 7.1 TO-92 package information Figure 17: TO-92 package outline Table 22: TO-92 mechanical data mm Dim. Min. Typ. Max. A b D E e e L R S W V 5 DocID2145 Rev 26 29/45
30 Package information 7.2 TO-92 packing information Figure 18: TO-92 tape and reel outline L78L 30/45 DocID2145 Rev 26
31 Package information Table 23: TO-92 tape and reel mechanical data mm Dim. Min. Typ. Max. A T 3.80 T T d P P F1, F F delta H W W W W H H H H D t 0.90 L I delta P Ø Ø u DocID2145 Rev 26 31/45
32 Package information 7.3 TO-92 Ammopak packing information Figure 19: TO-92 Ammopak tape and reel outline L78L 32/45 DocID2145 Rev 26
33 Dim. Package information Table 24: TO-92 Ammopak tape and reel mechanical data mm Min. Typ. Max. A T 3.80 T T d P P F1, F F delta H W W W W H H H H D t 0.90 L I delta P DocID2145 Rev 26 33/45
34 Package information 7.4 SO-8 package information Figure 20: SO-8 package outline L78L 34/45 DocID2145 Rev 26
35 Package information Table 25: SO-8 mechanical data mm Dim. Min. Typ. Max. A 1.75 A A b b c c D E E e 1.27 h L L L k 0 8 ccc 0.10 Figure 21: SO-8 recommended footprint (dimensions are in mm) DocID2145 Rev 26 35/45
36 Package information 7.5 SO-8 packing information Figure 22: SO-8 tape and reel dimensions L78L Table 26: SO-8 tape and reel mechanical data Dim. mm Min. Typ. Max. A 330 C D 20.2 N 60 T 22.4 Ao Bo Ko Po P /45 DocID2145 Rev 26
37 7.6 SOT-89 package information Figure 23: SOT-89 package outline Package information DocID2145 Rev 26 37/45
38 Package information Table 27: SOT-89 mechanical data mm Dim. Min. Typ. Max. A B B C C D D D E e e H H K 1 8 L R 0.25 β 90 L78L 38/45 DocID2145 Rev 26
39 Figure 24: SOT-89 recommended footprint Package information DocID2145 Rev 26 39/45
40 Package information 7.7 SOT-89 packing information Figure 25: SOT-89 carrier tape outline L78L Table 28: SOT-89 carrier tape mechanical data mm Dim. Value Tolerance Ao 4.91 ± 0.10 Bo 4.52 ± 0.10 Ko 1.90 ± 0.10 F 5.50 ± 0.10 E 1.75 ± 0.10 W 12 ± 0.30 P2 2 ± 0.10 Po 4 ± 0.10 P1 8 ± 0.10 T 0.30 ± 0.10 D Ø 1.55 ± 0.05 D1 Ø 1.60 ± /45 DocID2145 Rev 26
41 Ordering information 8 Ordering information SO-8 TO-92 (Bag) (1) Part numbers TO-92 (ammopack) Table 29: Order codes TO-92 (tape and reel) SOT-89 Output voltages L78L33ABD-TR L78L33ABZ-AP L78L33ABUTR 3.3 L78L33ACD13TR L78L33ACZ L78L33ACZ-AP L78L33ACZTR L78L33ACUTR 3.3 L78L33CD-TR 3.3 L78L05ABD13TR L78L05ABZ L78L05ABZ-AP L78L05ABZ-TR L78L05ABUTR 5 L78L05ACD13TR L78L05ACZ L78L05ACZ-AP L78L05ACZTR L78L05ACUTR 5 L78L05CD13TR L78L05CZ 5 L78L06ABZ L78L06ABUTR 6 L78L06ACD13TR L78L06ACUTR 6 L78L08ABD13TR L78L08ABZ-AP L78L08ABZTR L78L08ABUTR 8 L78L08ACD13TR L78L08ACZ L78L08ACZ-AP L78L08ACZTR L78L08ACUTR 8 L78L08CD13TR 8 L78L09ABD13TR L78L09ABZ L78L09ABUTR 9 L78L09ACD13TR L78L09ACZ-AP L78L09ACZ-TR L78L09ACUTR 9 L78L09CD13TR 9 (V) L78L10ACUTR 10 L78L12ABD-TR L78L12ABZ L78L12ABZ-AP L78L12ABUTR 12 L78L12ACD13TR L78L12ACZ L78L12ACZ-AP L78L12ACZ-TR L78L12ACUTR 12 L78L12CD13TR 12 L78L15ABZ-AP L78L15ABUTR 15 L78L15ACD13TR L78L15ACZ L78L15ACUTR 15 L78L15CD-TR 15 L78L18ACUTR 18 L78L18CD13TR 18 L78L24ABZ-TR 24 L78L24ACZ-AP L78L24ACUTR 24 L78L24CD-TR 24 Notes: (1) Available in Ammopak with the suffix "-AP" or in tape and reel with the suffix "TR". Please note that in these cases pins are shaped according to tape and reel specifications. DocID2145 Rev 26 41/45
42 Ordering information L78L Table 30: Marking information Part numbers Marking Packages Output voltages L78L05ABD13TR 78L05B SO-8 5 V L78L05ABUTR 8C SOT-89 5 V L78L05ABZ L78L05A TO-92 5 V L78L05ABZ-AP L78L05A TO-92 5 V L78L05ABZ-TR L78L05A TO-92 5 V L78L05ACD13TR 78L05A SO-8 5 V L78L05ACUTR 8C SOT-89 5 V L78L05ACZ L78L05A TO-92 5 V L78L05ACZ-AP L78L05A TO-92 5 V L78L05ACZTR L78L05A TO-92 5 V L78L05CD13TR 78L05 SO-8 5 V L78L05CZ L78L05A TO-92 5 V L78L06ABUTR 8E SOT-89 6 V L78L06ABZ L78L06A TO-92 6 V L78L06ACD13TR L78L06A SO-8 6 V L78L06ACUTR 8E SOT-89 6 V L78L08ABD13TR 78L08B SO-8 8 V L78L08ABUTR 8G SOT-89 8 V L78L08ABZ-AP L78L08A TO-92 8 V L78L08ABZTR L78L08A TO-92 8 V L78L08ACD13TR 78L08A SO-8 8 V L78L08ACUTR 8G SOT-89 8 V L78L08ACZ L78L08A TO-92 8 V L78L08ACZ-AP L78L08A TO-92 8 V L78L08ACZTR L78L08A TO-92 8 V L78L08CD13TR 78L08 SO-8 8 V L78L09ABD13TR 78L09B SO-8 8 V L78L09ABZ L78L09A TO-92 9 V L78L09ABUTR 8H SOT-89 9 V L78L09ACD13TR 78L09A SO8 9 V L78L09ACUTR 8H SOT-89 9 V L78L09ACZ-AP L78L09A TO-92 9 V L78L09ACZ-TR L78L09A TO-92 9 V L78L09CD13TR L78L09A SO-8 9 V L78L10ACUTR 8I SOT V L78L12ABD-TR 78L12B SO-8 12 V L78L12ABUTR 8K SOT V L78L12ABZ L78L12A TO V L78L12ABZ-AP L78L12A TO V 42/45 DocID2145 Rev 26
43 Ordering information Part numbers Marking Packages Output voltages L78L12ACD13TR 78L12A SO-8 12 V L78L12ACUTR 8K SOT V L78L12ACZ L78L12A TO V L78L12ACZ-AP L78L12A TO V L78L12ACZ-TR L78L12A TO V L78L12CD13TR 78L12 SO-8 12 V L78L15ABUTR 8L SOT V L78L15ABZ-AP L78L15A TO V L78L15ACD13TR 78L15A SO-8 15 V L78L15ACUTR 8L SOT V L78L15ACZ L78L15A TO V L78L15CD-TR 78L15 SO-8 15 V L78L18ACUTR 8B SOT V L78L18CD13TR L78L18 SO-8 18 V L78L24ABZ-TR L78L24A TO V L78L24ACUTR 8P SOT V L78L24ACZ-AP L78L24A TO V L78L24CD-TR 78L24 SO-8 24 V L78L33ABD-TR 78L33B SO V L78L33ABUTR 8A SOT V L78L33ABZ-AP L78L33A TO V L78L33ACD13TR 78L33A SO V L78L33ACUTR 8A SOT V L78L33ACZ L78L33A TO V L78L33ACZ-AP L78L33A TO V L78L33ACZTR L78L33A TO V DocID2145 Rev 26 43/45
44 Revision history L78L 9 Revision history Table 31: Document revision history Date Revision Changes 14-Mar Add tape and reel for TO Mar Add note on Table Dec Mistake on ordering Table in header. 12-Sep Order codes updated. 07-Jun Order codes updated. 18-Sep Added Table 1 in cover page. 15-Jul Modified: Table 1 and Table 28: Order codes. 18-Aug Modified Figure 12 on page Apr Added: RthJA value for SOT-89 Table 2 on page Feb Added note Table 26 on page Feb Modified: SOT-89 Figure 2 on page Aug Updated TOP value for L78L00AC in Table 1 on page 5. Minor text changes. 07-Sep Added: Table 29: Marking information. 14-Apr Oct Feb Feb Jun Part numbers L78LxxAB, L78LxxAC, L78LxxC changed to L78L. Removed Table1: Device summary. Updated features and description in cover page, Table 28: Order codes, Table 29: Marking information and Section 7: Package information. Added Section: Packing mechanical data. Minor text changes. Updated Table 28: Order codes and Table 29: Marking information. Minor text changes. Updated Table 29: Marking information. Minor text changes. Updated Table 29: Marking information and Section 7.7: SOT-89 packing information. Minor text changes. Changed test condition values for the parameter "Line regulation" and the typical value for the parameter "Dropout voltage" in : Table 3: "Electrical characteristics of L78L33C", Table 4: "Electrical characteristics of L78L05C", Table 12: "Electrical characteristics of L78L33AB and L78L33AC" and Table 13: "Electrical characteristics of L78L05AB and L78L05AC". Minor text changes. 44/45 DocID2145 Rev 26
45 IMPORTANT NOTICE PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document STMicroelectronics All rights reserved DocID2145 Rev 26 45/45
Description SO-8. Table 1. Device summary. Order codes. SO-8 (tape and reel) TO-92 (Bag) TO-92 (Ammopack) TO-92 (tape and reel)
Low current 1.2 to 37 V adjustable voltage regulators Description Datasheet - production data TO-92 SO-8 TO-92 Tape and reel Bag Ammopack Features Outuput voltage range: 1.2 to 37 V Output current up to
LM217M, LM317M. Medium current 1.2 to 37 V adjustable voltage regulator. Description. Features
Medium current 1.2 to 37 V adjustable voltage regulator Datasheet - production data Description The LM217M and LM317M are monolithic integrated circuits in DPAK package used as positive adjustable voltage
STLQ015. 150 ma, ultra low quiescent current linear voltage regulator. Description. Features. Application
150 ma, ultra low quiescent current linear voltage regulator Description Datasheet - production data Features SOT23-5L Input voltage from 1.5 to 5.5 V Very low quiescent current: 1.0 µa (typ.) at no load
Description SO-8. series. Furthermore, in the 8-pin configuration Very low-dropout voltage (0.2 V typ.)
ery low-dropout voltage regulator with inhibit function TO-92 Bag TO-92 Tape and reel Ammopack 1 2 3 SO-8 Description Datasheet - production data The is a very low-dropout voltage regulator available in
L78MxxAB L78MxxAC. Precision 500 ma regulators. Features. Description
L78MxxAB L78MxxAC Precision 500 ma regulators Features Output current to 0.5 A Output voltages of 5; 6; 8; 9; 10; 12; 15; 18; 24 V Thermal overload protection Short circuit protection Output transition
L78. Positive voltage regulator ICs. Description. Features
Positive voltage regulator ICs Description Datasheet - production data TO-220 Features DPAK TO-220FP D²PAK Output current up to 1.5 A Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18; 24 V Thermal overload
Description. Table 1. Device summary
2 A positive voltage regulator IC Description Datasheet - production data Features TO-220 Output current up to 2 A Output voltages of 5; 7.5; 9; 10; 12; 15; 18; 24 V Thermal protection Short circuit protection
LM337. Three-terminal adjustable negative voltage regulators. Features. Description
Three-terminal adjustable negative voltage regulators Datasheet - production data current limit, thermal overload protection and safe area protection. All overload protection circuitry remains fully functional
Description. Table 1. Device summary. Order codes. TO-220 (single gauge) TO-220 (double gauge) D²PAK (tape and reel) TO-220FP
1.2 V to 37 V adjustable voltage regulators Description Datasheet - production data TO-220 TO-220FP The LM217, LM317 are monolithic integrated circuits in TO-220, TO-220FP and D²PAK packages intended for
MC78XX/LM78XX. 3-terminal 1A positive voltage regulator. Features. Description. Internal Block Digram. www.fairchildsemi.com
www.fairchildsemi.com 3-terminal 1A positive voltage regulator Features Current up to 1A Voltages of 5, 6, 8, 9, 10, 11, 12, 15, 18, 24V Thermal Overload Protection Short Circuit Protection Transistor
L4940 series VERY LOW DROP 1.5 A REGULATORS
L4940 series VERY LOW DROP 1.5 A REGULATORS PRECISE 5 V, 8.5 V, 10 V, 12 V OUTPUTS LOW DROPOUT VOLTAGE (500 typ at 1.5A) VERY LOW QUIESCENT CURRENT THERMAL SHUTDOWN SHORT CIRCUIT PROTECTION REVERSE POLARITY
TDA2004R. 10 + 10 W stereo amplifier for car radio. Features. Description
10 + 10 W stereo amplifier for car radio Features Low distortion Low noise Protection against: Output AC short circuit to ground Overrating chip temperature Load dump voltage surge Fortuitous open ground
Trench gate field-stop IGBT, M series 650 V, 10 A low loss. Features. Description
Trench gate field-stop IGBT, M series 650 V, 10 A low loss Datasheet - production data TAB D2PAK 1 3 Features 6 µs of short-circuit withstand time VCE(sat) = 1.55 V (typ.) @ IC = 10 A Tight parameter distribution
L7800 SERIES POSITIVE VOLTAGE REGULATORS
SERIES POSITIVE VOLTAGE REGULATORS OUTPUT CURRENT UP TO 1.5 A OUTPUT VOLTAGES OF 5; 5.2; 6; 8; 8.5; 9; 12; 15; 18; 24V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION OUTPUT TRANSITION SOA PROTECTION
TDA2003 10W CAR RADIO AUDIO AMPLIFIER
TDA2003 10W CAR RADIO AUDIO AMPLIFIER DESCRIPTION The TDA 2003 has improved performance with the same pin configuration as the TDA 2002. The additional features of TDA 2002, very low number of external
STCS1. 1.5 A max constant current LED driver. Features. Applications. Description
1.5 A max constant current LED driver Features Up to 40 V input voltage Less than 0.5 V voltage overhead Up to 1.5 A output current PWM dimming pin Shutdown pin LED disconnection diagnostic DFN8 (3x3 mm)
STPS5L60. Power Schottky rectifier. Description. Features
Power Schottky rectifier Datasheet - production data Description Power Schottky rectifier suited for switch mode power supplies and high frequency inverters. This device is intended for use in low voltage
MC33079. Low noise quad operational amplifier. Features. Description
Low noise quad operational amplifier Datasheet production data Features Low voltage noise: 4.5 nv/ Hz High gain bandwidth product: 15 MHz High slew rate: 7 V/µs Low distortion: 0.002% Large output voltage
UA741. General-purpose single operational amplifier. Features. Applications. Description. N DIP8 (plastic package)
General-purpose single operational amplifier Datasheet - production data N DIP8 (plastic package) D SO8 (plastic micropackage) Pin connections (top view) 1 - Offset null 1 2 - Inverting input 3 - Non-inverting
Features. Description. Table 1. Device summary. Order code Marking Package Packing. STP110N8F6 110N8F6 TO-220 Tube
N-channel 80 V, 0.0056 Ω typ.,110 A, STripFET F6 Power MOSFET in a TO-220 package Features Datasheet - production data Order code V DS R DS(on)max I D P TOT TAB STP110N8F6 80 V 0.0065 Ω 110 A 200 W TO-220
Order code Temperature range Package Packaging
ST485B ST485C Low power RS-485/RS-422 transceiver Features Low quiescent current: 300 µa Designed for RS-485 interface application - 7 V to 12 V common mode input voltage range Driver maintains high impedance
L78M00 SERIES POSITIVE VOLTAGE REGULATORS. www.tvsat.com.pl
SERIES POSITIVE VOLTAGE REGULATORS OUTPUT CURRENT TO 0.5A OUTPUT VOLTAGES OF 5; 6; 8; 9; 10; 12; 15; 18; 20; 24V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION OUTPUT TRANSISTOR SOA PROTECTION DESCRIPTION
MC34063AB, MC34063AC, MC34063EB, MC34063EC
MC34063AB, MC34063AC, MC34063EB, MC34063EC DC-DC converter control circuits Description Datasheet - production data Features DIP-8 SO-8 Output switch current in excess of 1.5 A 2 % reference accuracy Low
STCS1A. 1.5 A max constant current LED driver. Features. Applications. Description
1.5 A max constant current LED driver Features Up to 40 V input voltage Less than 0.5 V voltage overhead Up to 1.5 A output current PWM dimming pin Shutdown pin LED disconnection diagnostic DFN8 (3 x 3
TS555. Low-power single CMOS timer. Description. Features. The TS555 is a single CMOS timer with very low consumption:
Low-power single CMOS timer Description Datasheet - production data The TS555 is a single CMOS timer with very low consumption: Features SO8 (plastic micropackage) Pin connections (top view) (I cc(typ)
DSL03. Low capacitance TVS for high speed lines such as xdsl. Description. Features. Complies with the following standards
Low capacitance TVS for high speed lines such as xdsl Description Datasheet - production data Features High surge capability to comply with GR-1089 and ITU-T K20/21 Keeps its peak power capability up to
ULN2801A, ULN2802A, ULN2803A, ULN2804A
ULN2801A, ULN2802A, ULN2803A, ULN2804A Eight Darlington array Datasheet production data Features Eight Darlington transistors with common emitters Output current to 500 ma Output voltage to 50 V Integral
Obsolete Product(s) - Obsolete Product(s)
32 W hi-fi audio power amplifier Features High output power (50 W music power IEC 268.3 rules) High operating supply voltage (50 V) Single or split supply operations Very low distortion Short-circuit protection
STLM20. Ultra-low current 2.4 V precision analog temperature sensor. Features. Applications
Ultra-low current 2.4 V precision analog temperature sensor Features Precision analog voltage output temperature sensor ±1.5 C maximum temperature accuracy at 25 C (±0.5 C typical) Ultra-low quiescent
STCS2A. 2 A max constant current LED driver. Features. Applications. Description
2 A max constant current LED driver Features Up to 40 V input voltage Less than 0.5 V voltage overhead Up to 2 A output current PWM dimming pin Shutdown pin LED disconnection diagnostic Slope control with
Description. Table 1. Device summary. Order code Temperature range Package Packaging Marking
14-stage ripple carry binary counter/divider and oscillator Applications Automotive Industrial Computer Consumer Description Datasheet - production data Features Medium speed operation Common reset Fully
ULN2001, ULN2002 ULN2003, ULN2004
ULN2001, ULN2002 ULN2003, ULN2004 Seven Darlington array Datasheet production data Features Seven Darlingtons per package Output current 500 ma per driver (600 ma peak) Output voltage 50 V Integrated suppression
L6234. Three phase motor driver. Features. Description
Three phase motor driver Features Supply voltage from 7 to 52 V 5 A peak current R DSon 0.3 Ω typ. value at 25 C Cross conduction protection TTL compatible driver Operating frequency up to 150 khz Thermal
STIEC45-xxAS, STIEC45-xxACS
Transil TVS for IEC 61000-4-5 compliance Datasheet - production data differential mode MIL STD 883G, method 3015-7 Class 3B 25 kv HBM (human body model) Resin meets UL 94, V0 MIL-STD-750, method 2026 solderability
EN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at www.hest ore.hu.
EN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at www.hest ore.hu. 2N3055, MJ2955 Complementary power transistors Features Datasheet - production
LM2901. Low-power quad voltage comparator. Features. Description
Low-power quad voltage comparator Features Wide single supply voltage range or dual supplies for all devices: +2 V to +36 V or ±1 V to ±18 V Very low supply current (1.1 ma) independent of supply voltage
ADJUSTABLE VOLTAGE AND CURRENT REGULATOR
L200 ADJUSTABLE VOLTAGE AND CURRENT REGULATOR ADJUSTABLE OUTPUT CURRENT UP TO 2 A (GUARANTEED UP TO Tj = 150 C) ADJUSTABLE OUTPUT VOLTAGE DOWN TO 2.85 V INPUT OVERVOLTAGE PROTECTION (UP TO 60 V, 10 ms)
LM134-LM234-LM334. Three terminal adjustable current sources. Features. Description
Three terminal adjustable current sources Features Operates from 1V to 40V 0.02%/V current regulation Programmable from 1µA to 10mA ±3% initial accuracy Description The LM134/LM234/LM334 are 3-terminal
LF00AB/C SERIES VERY LOW DROP VOLTAGE REGULATORS WITH INHIBIT
LF00AB/C SERIES ERY LOW DROP OLTAGE REGULATORS WITH INHIBIT ERY LOW DROPOUT OLTAGE (5) ERY LOW QUIESCENT CURRENT (TYP. 50 µa IN OFF MODE, 500µA INON MODE) OUTPUT CURRENT UP TO 500 ma LOGIC-CONTROLLED ELECTRONIC
STOD2540. PMOLED display power supply. Features. Application. Description
PMOLED display power supply Features Inductor switches boost controller PFM mode control High efficiency over wide range of load (1 ma to 40 ma) Integrated load disconnect switch Over voltage protection
2STBN15D100. Low voltage NPN power Darlington transistor. Features. Application. Description
Low voltage NPN power Darlington transistor Features Good h FE linearity High f T frequency Monolithic Darlington configuration with integrated antiparallel collector-emitter diode TAB Application Linear
ST13005. High voltage fast-switching NPN power transistor. Features. Applications. Description
High voltage fast-switching NPN power transistor Datasheet production data Features Low spread of dynamic parameters Minimum lot-to-lot spread for reliable operation Very high switching speed Applications
VN5R003H-E. 3 mω reverse battery protection switch. Features. Description. Application
3 mω reverse battery protection switch Datasheet production data Features Max supply voltage V CC -16 to 41 V Operating voltage range V CC -16 to 28 V On-state resistance R ON 3mΩ General Optimized electromagnetic
LM135-LM235-LM335. Precision temperature sensors. Features. Description
Precision temperature sensors Features Directly calibrated in K 1 C initial accuracy Operates from 450µA to 5mA Less than 1Ω dynamic impedance TO-92 (Plastic package) Description The LM135, LM235, LM335
STWD100. Watchdog timer circuit. Description. Features. Applications
Watchdog timer circuit Description Datasheet - production data SOT23-5 (WY) Features SC70-5, SOT323-5 (W8) Current consumption 13 µa typ. Available watchdog timeout periods are 3.4 ms, 6.3 ms, 102 ms,
STTH1R04-Y. Automotive ultrafast recovery diode. Features. Description
Automotive ultrafast recovery diode Features Datasheet - production data K SMA STTH1R4AY Table 1. Device summary Symbol Value I F(AV) 1 A V RRM 4 V T j (max) 175 C V F (typ) t rr (typ) A K.9 V 14 ns A
Obsolete Product(s) - Obsolete Product(s)
Vertical deflection booster for 3 App TV/monitor applications with 0 V flyback generator Features Figure. Heptawatt package Power amplifier Flyback generator Stand-by control Output current up to 3.0 App
TDA2822 DUAL POWER AMPLIFIER SUPPLY VOLTAGE DOWN TO 3 V LOW CROSSOVER DISTORSION LOW QUIESCENT CURRENT BRIDGE OR STEREO CONFIGURATION
TDA2822 DUAL POER AMPLIFIER SUPPLY VOLTAGE DON TO 3 V. LO CROSSOVER DISTORSION LO QUIESCENT CURRENT BRIDGE OR STEREO CONFIGURATION DESCRIPTION The TDA2822 is a monolithic integrated circuit in 12+2+2 powerdip,
50 ohm nominal input / conjugate match balun to nrf51822- CEAA/CDAB/CFAC and nrf51422-ceaa/cdab/cfac. Benefits. Description
50 ohm nominal input / conjugate match balun to nrf51822- /CDAB/CFAC and nrf51422-/cdab/cfac Datasheet production data Benefits Very low profile: < 560 µm after reflow High RF performance RF BOM and area
Table 1. Absolute maximum ratings (T amb = 25 C) Symbol Parameter Value Unit. ISO 10605 - C = 330 pf, R = 330 Ω : Contact discharge Air discharge
Automotive dual-line Transil, transient voltage suppressor (TVS) for CAN bus Datasheet - production data Complies with the following standards ISO 10605 - C = 150 pf, R = 330 Ω : 30 kv (air discharge)
BZW50. Transil, transient voltage surge suppressor (TVS) Features. Description
Transil, transient voltage surge suppressor (TVS) Datasheet production data Features Peak pulse power: 5000 W (10/0 µs) Stand-off voltage range from 10 V to 180 V Unidirectional and bidirectional types
BD238. Low voltage PNP power transistor. Features. Applications. Description. Low saturation voltage PNP transistor
Low voltage PNP power transistor Features Low saturation voltage PNP transistor Applications Audio, power linear and switching applications Description The device is manufactured in planar technology with
Symbol Parameter Value Unit V i-o Input-output Differential Voltage 40 V I O Output Current Intenrally Limited Top
LM117/217 LM317 1.2V TO 37V VOLTAGE REGULATOR OUTPUT VOLTAGE RANGE : 1.2 TO 37V OUTPUT CURRENT IN EXCESS OF 1.5A 0.1% LINE AND LOAD REGULATION FLOATING OPERATION FOR HIGH VOLTAGES COMPLETE SERIES OF PROTECTIONS
STN3NF06L. N-channel 60 V, 0.07 Ω, 4 A, SOT-223 STripFET II Power MOSFET. Features. Application. Description
N-channel 60 V, 0.07 Ω, 4 A, SOT-223 STripFET II Power MOSFET Features Type V DSS (@Tjmax) Exceptional dv/dt capability Avalanche rugged technology 100% avalanche tested R DS(on) max STN3NF06L 60 V < 0.1
BD135 - BD136 BD139 - BD140
BD135 - BD136 BD139 - BD140 Complementary low voltage transistor Features Products are pre-selected in DC current gain Application General purpose Description These epitaxial planar transistors are mounted
LM2902. Low-power quad operational amplifier. Features. Description
Low-power quad operational amplifier Datasheet production data Features Wide gain bandwidth: 1.3 MHz Input common-mode voltage range includes negative rail Large voltage gain: 100 db Very low supply current
P6KE. Transil, transient voltage surge suppressor (TVS) Features. Description. Complies with the following standards
Transil, transient voltage surge suppressor (TVS) Datasheet production data Features Peak pulse power: 600 W (10/0 µs ) Stand-off voltage range 6.8 to 440 V Unidirectional and bidirectional types Low clamping
ESDLIN1524BJ. Transil, transient voltage surge suppressor diode for ESD protection. Features. Description SOD323
Transil, transient voltage surge suppressor diode for ESD protection Datasheet production data Features Max peak pulse power 160 W (8/0 µs) Asymmetrical bidirectional device Stand-off voltage: 15 and 4
Description. Table 1. Device summary. Order code Package Packing
4 x 41 W quad bridge car radio amplifier Datasheet - production data Features Flexiwatt25 High output power capability: 4 x 41 W / 4 max. Low distortion Low output noise Standby function Mute function
MC78XX/LM78XX/MC78XXA
3-Terminal 1A Positive oltage Regulator www.fairchildsemi.com Features Output Current up to 1A Output oltages of 5, 6, 8, 9, 10, 12, 15, 18, 24 Thermal Overload Protection Short Circuit Protection Output
LM78XX Series Voltage Regulators
LM78XX Series Voltage Regulators General Description Connection Diagrams The LM78XX series of three terminal regulators is available with several fixed output voltages making them useful in a wide range
KA79XX/KA79XXA. 3-Terminal 1A Negative Voltage Regulator. Features. Description. Internal Block Digram. www.fairchildsemi.com
3-Terminal 1A Negative oltage Regulator www.fairchildsemi.com Features Output Current in Excess of 1A s of -5, -6, -8, -9, -12, -15, -18, -24 Internal Thermal Overload Protection Short Circuit Protection
1.0A LOW DROPOUT LINEAR REGULATOR
1.0A LOW DROPOUT LINEAR REGULATOR Description Pin Assignments The is a low dropout three-terminal regulator with 1.0A output current ability, and the dropout voltage is specified at typical 1.1V at 1.0A
BD241A BD241C. NPN power transistors. Features. Applications. Description. NPN transistors. Audio, general purpose switching and amplifier transistors
BD241A BD241C NPN power transistors Features. NPN transistors Applications Audio, general purpose switching and amplifier transistors Description The devices are manufactured in Planar technology with
DDSL01. Secondary protection for DSL lines. Features. Description
Secondary protection for DSL lines Features Stand off voltage: 30 V Surge capability: I pp = 30 A 8/20 µs Low capacitance device: 4.5 pf at 2 V RoHS package Low leakage current: 0.5 µa at 25 C 3 2 Description
ETP01-xx21. Protection for Ethernet lines. Features. Description. Applications. Benefits. Complies with the following standards
ETP0-xx2 Protection for Ethernet lines Features Differential and common mode protection Telcordia GR089 Intrabuilding: 50 A, 2/0 µs ITU-T K20/2: 40 A, 5/30 µs Low capacitance: 3 pf max at 0 V UL94 V0 approved
STTH2R06. High efficiency ultrafast diode. Features. Description
STTH2R6 High efficiency ultrafast diode Features Very low conduction losses Negligible switching losses Low forward and reverse recovery times High junction temperature Description A K The STTH2R6 uses
TS321 Low Power Single Operational Amplifier
SOT-25 Pin Definition: 1. Input + 2. Ground 3. Input - 4. Output 5. Vcc General Description The TS321 brings performance and economy to low power systems. With high unity gain frequency and a guaranteed
Features. Applications
Pb Lead-Free 1A LOW DROPOUT LINEAR REGULATOR Description The is a series of low dropout three-terminal regulators with a dropout of 1.15V at 1A output current. The series provides current limiting and
VN05N. High side smart power solid state relay PENTAWATT. Features. Description
High side smart power solid state relay Features Type V DSS R DS(on) I OUT V CC VN05N 60 V 0.18 Ω 13 A 26 V Output current (continuous): 13A @ Tc=25 C 5V logic level compatible input Thermal shutdown Under
Aluminum Electrolytic Capacitors Axial Miniature, Long-Life
Aluminum Electrolytic Capacitors Axial Miniature, Long-Life 38 AML 0 ASM smaller dimensions Fig. QUICK REFERENCE DATA DESCRIPTION Nominal case sizes (Ø D x L in mm) 6.3 x.7 to 0 x 5 VALUE 0 x 30 to x 38
STP60NF06. N-channel 60V - 0.014Ω - 60A TO-220 STripFET II Power MOSFET. General features. Description. Internal schematic diagram.
N-channel 60V - 0.014Ω - 60A TO-220 STripFET II Power MOSFET General features Type V DSS R DS(on) I D STP60NF06 60V
STGB10NB37LZ STGP10NB37LZ
STGB10NB37LZ STGP10NB37LZ 10 A - 410 V internally clamped IGBT Features Low threshold voltage Low on-voltage drop Low gate charge TAB TAB High current capability High voltage clamping feature Applications
DSL01-xxxSC5. Secondary protection for DSL lines. Features. Description. Applications. Benefits. Complies with the following standards
-xxxsc5 Secondary protection for DSL lines Features Low capacitance devices: -xxxsc5: Delta C typ = 3.5 pf High surge capability: 30 A - 8/20 µs Voltage: 8 V, 10.5 V, 16 V, and 24 V RoHS package Benefits
L6384E. High voltage half-bridge driver. Description. Features. Applications
High voltage half-bridge driver Description Datasheet - production data Features High voltage rail up to 600 V dv/dt immunity ± 50 V/nsec in full temperature range Driver current capability 400 ma source
NE555 SA555 - SE555. General-purpose single bipolar timers. Features. Description
NE555 SA555 - SE555 General-purpose single bipolar timers Features Low turn-off time Maximum operating frequency greater than 500 khz Timing from microseconds to hours Operates in both astable and monostable
STP55NF06L STB55NF06L - STB55NF06L-1
General features STP55NF06L STB55NF06L - STB55NF06L-1 N-channel 60V - 0.014Ω - 55A TO-220/D 2 PAK/I 2 PAK STripFET II Power MOSFET Type V DSS R DS(on) I D STP55NF06L 60V
IR Receiver Module for Light Barrier Systems
Not for New Design - Alternative Available: New TSSP4038 (#82458) www.vishay.com IR Receiver Module for Light Barrier Systems TSOP4038 2 3 MECHANICAL DATA Pinning: = OUT, 2 = GND., 3 = V S 6672 FEATURES
LM350. 3.0 A, Adjustable Output, Positive Voltage Regulator THREE TERMINAL ADJUSTABLE POSITIVE VOLTAGE REGULATOR
3. A, able Output, Positive Voltage Regulator The is an adjustable threeterminal positive voltage regulator capable of supplying in excess of 3. A over an output voltage range of 1.2 V to 33 V. This voltage
Description. Table 1. Device summary. Order code Temperature range Package Packing Marking
8-bit shift register with output latches (3-state) Applicatio Datasheet - production data SO16 TSSOP16 Automotive Industrial Computer Coumer Features High speed: f MAX = 59 MHz (typ.) at V CC = 6 V Low
STB4NK60Z, STB4NK60Z-1, STD4NK60Z STD4NK60Z-1, STP4NK60Z,STP4NK60ZFP
STB4NK60Z, STB4NK60Z-1, STD4NK60Z STD4NK60Z-1, STP4NK60Z,STP4NK60ZFP N-channel 600 V - 1.76 Ω - 4 A SuperMESH Power MOSFET DPAK - D 2 PAK - IPAK - I 2 PAK - TO-220 - TO-220FP Features Type V DSS R DS(on)
Advanced Monolithic Systems
Advanced Monolithic Systems FEATURES Three Terminal Adjustable or Fixed oltages* 1.5, 1.8, 2.5, 2.85, 3.3 and 5. Output Current of 1A Operates Down to 1 Dropout Line Regulation:.2% Max. Load Regulation:.4%
STP60NF06FP. N-channel 60V - 0.014Ω - 30A TO-220FP STripFET II Power MOSFET. General features. Description. Internal schematic diagram.
N-channel 60V - 0.014Ω - 30A TO-220FP STripFET II Power MOSFET General features Type V DSS R DS(on) I D STP60NF06FP 60V
L293B L293E PUSH-PULL FOUR CHANNEL DRIVERS. OUTPUT CURRENT 1A PER CHANNEL PEAK OUTPUT CURRENT 2A PER CHANNEL (non repetitive) INHIBIT FACILITY
L293B L293E PUSH-PULL FOUR CHANNEL DRIVERS OUTPUT CURRENT 1A PER CHANNEL PEAK OUTPUT CURRENT 2A PER CHANNEL (non repetitive) INHIBIT FACILITY. HIGH NOISE IMMUNITY SEPARATE LOGIC SUPPLY OVERTEMPERATURE
LM833 LOW NOISE DUAL OPERATIONAL AMPLIFIER
LOW NOISE DUAL OPERATIONAL AMPLIFIER LOW VOLTAGE NOISE: 4.5nV/ Hz HIGH GAIN BANDWIDTH PRODUCT: 15MHz HIGH SLEW RATE: 7V/µs LOW DISTORTION:.2% EXCELLENT FREQUENCY STABILITY ESD PROTECTION 2kV DESCRIPTION
TSV321, TSV358, TSV324, TSV321A, TSV358A, TSV324A,
TSV321, TSV358, TSV324, TSV321A, TSV358A, General purpose input/output rail-to-rail low-power operational amplifiers Datasheet - production data Pin connections (top view) SOT23-5 SO8 SO8, MiniSO8, TSSOP8
STTH110. High voltage ultrafast rectifier. Description. Features
High voltage ultrafast rectifier Datasheet - production data K Description The STTH110, which is using ST ultrafast high voltage planar technology, is especially suited for free-wheeling, clamping, snubbering,
NE555 SA555 - SE555. General-purpose single bipolar timers. Features. Description
NE555 SA555 - SE555 General-purpose single bipolar timers Features Low turn-off time Maximum operating frequency greater than 500 khz Timing from microseconds to hours Operates in both astable and monostable
STM6315. Open drain microprocessor reset. Features
Open drain microprocessor reset Features Low supply current of 1.5µA (typ) ±1.8% reset threshold accuracy (25 C) Guaranteed RST assertion down to V CC = 1.0V Open drain RST output can exceed V CC Power
STB75NF75 STP75NF75 - STP75NF75FP
STB75NF75 STP75NF75 - STP75NF75FP N-channel 75V - 0.0095Ω - 80A - TO-220 - TO-220FP - D 2 PAK STripFET II Power MOSFET General features Type V DSS R DS(on) I D STB75NF75 75V
CS8481. 3.3 V/250 ma, 5.0 V/100 ma Micropower Low Dropout Regulator with ENABLE
3.3 /250 ma, 5.0 /100 ma Micropower Low Dropout Regulator with The CS8481 is a precision, dual Micropower linear voltage regulator. The switched 3.3 primary output ( OUT1 ) supplies up to 250 ma while
LDS8720. 184 WLED Matrix Driver with Boost Converter FEATURES APPLICATION DESCRIPTION TYPICAL APPLICATION CIRCUIT
184 WLED Matrix Driver with Boost Converter FEATURES High efficiency boost converter with the input voltage range from 2.7 to 5.5 V No external Schottky Required (Internal synchronous rectifier) 250 mv
5A LOW DROPOUT LINEAR REGULATOR General Description. Features. Applications
General Description The is a series of low dropout positive voltage regulators with a maximum dropout of.5v at 5A of load current. The series features on-chip thermal limiting which provides protection
STB60N55F3, STD60N55F3, STF60N55F3 STI60N55F3, STP60N55F3, STU60N55F3
STB60N55F3, STD60N55F3, STF60N55F3 STI60N55F3, STP60N55F3, STU60N55F3 N-channel 55 V, 6.5 mω, 80 A, DPAK, IPAK, D 2 PAK, I 2 PAK, TO-220 TO-220FP STripFET III Power MOSFET Features Type V DSS R DS(on)
1A L.D.O VOLTAGE REGULATOR
FEATURES Output Current up to 1 A Low Dropout Voltage (1.2V at 1A Output current) Three Terminal Adjustable(ADJ) or Fixed 1.2V, 1.5V, 1.8V, 2.5V, 2.85V, 5.0V Line Regulation typically at 0.1% max. Load
L6219. Stepper motor driver. Features. Description
Stepper motor driver Features Able to drive both windings of bipolar stepper motor Output current up to 750 ma each winding Wide voltage range: 10 V to 46 V Half-step, full-step and microstepping mode
TL084 TL084A - TL084B
A B GENERAL PURPOSE JFET QUAD OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORTCIRCUIT PROTECTION HIGH INPUT IMPEDANCE
VNI2140JTR. Dual high side smart power solid state relay. Features. Description
Dual high side smart power solid state relay Features Type (1) V demag (1) R DSon (1) I out V CC -45 V 0.08 Ω 1 A (2) V CC 45 V 1. Per channel 2. Current limitation Nominal current: 0.5 A per channel Shorted
L5970D. Up to 1A step down switching regulator. Features. Description. Applications L5970D
Up to 1A step down switching regulator Features Up to 1A output current Operating input voltage from 4.4V to 36V 3.3V / (±%) reference voltage Output voltage adjustable from 1.V to 35V Low dropout operation:
STP10NK80ZFP STP10NK80Z - STW10NK80Z
STP10NK80ZFP STP10NK80Z - STW10NK80Z N-channel 800V - 0.78Ω - 9A - TO-220/FP-TO-247 Zener-protected supermesh TM MOSFET General features Type V DSS R DS(on) I D Pw STP10NK80Z 800V