ACS5000 Reader Wiring Guide 10/16/2014 2
Table of Contents Proximity Readers Manufacturer Model(s) Page HID 5355 ProxPro 5 HID 6005 Proxpoint, 5395 ThinlineII, 5365 Mini-Prox 6 FARPOINTE DATA P-300, P-500 7 Smart Card Readers Manufacturer Model(s) Page HID 6100 R10, 6140 R15, 6110 R30, 6120 R40, 6130 RK40, 6150 R90 8-9 FARPOINTE DATA Delta3, Delta5, Delta6.4 10 Multi-Technology Readers Manufacturer Model(s) Page HID 6145 RP15, 6125 RP40, 6136 RPK40 11-12 Wireless Receivers Manufacturer Model(s) Page CHAMBERLAIN Centex Wireless Receiver 13 FARPOINTE DATA Ranger Wireless Receiver 14 3
Grounding the Shields Shielded reader wire is required for all Brivo ACS5000 installations. The shield for each reader run should be tied to the grounding lug located in the lower left corner of the ACS5000 panel chassis. The chassis should then be grounded to a reliable earth ground. An electrical ground is usually not acceptable for Brivo installations, therefore it should not be considered for the panel ground. The diagram below shows a typical earth ground. Reader The reader shield should never be connected at the reader Reader Grounding Bus To ensure that the reader shield does not make contact with board level components or other wires, either use a jacketed 18AWG cable between the drain or shield and the grounding lug, or use heat shrink in order to isolate the drain or shield.! NEVER CONNECT YOUR GROUND WHILE THE PANEL EQUIPMENT IS ENERGIZED. DISCONNECT ALL BATTERIES AND REMOVE AC POWER FROM THE PANEL PRIOR TO CONNECTING GROUNDS. 4
Preface Brivo Systems conforms to the SIA Access Control Standard Protocol for the 26-bit Wiegand Reader Interface. Due to varieties of implementation in Wiegand, Brivo chooses to validate the reader in the marketplace for compatibility and the reliability between two systems. In the event that you are attempting to purchase or install a reader to be used with a Brivo ACS5000 Panel, it is recommended that you first review the Reader Wiring Guide for known compatible readers. Any reader that is not currently covered under the ACS5000 Reader Wiring Guide can be tested and added to the guide. Instructions on having a reader tested are contained at the end of this document. Legacy readers may be covered under previous versions of the ACS5000 Reader Wiring Guide. Legacy readers have been removed from the current ACS5000 Reader Wiring Guide due to a lack of hardware to validate operation. If a legacy reader is to be used, please contact Technical Support for access to a previous version that may include the legacy reader. The readers that have been validated, yet omitted from this guide are: AWID Sentinel-Prox KP-6840 AWID Sentinel-Prox LR-911 AWID Sentinel-Prox MM-6800 AWID Sentinel-Prox MR-1824 AWID Sentinel-Prox SP-6820 AWID Sentinel-Prox SR-2400 Northern BR-7 Barcode Reader Bioscrypt V Smart, A Bioscrypt VeriProx, V, H If a previously supported reader is not included in this guide and not listed above, that reader is no longer valid for use with the ACS5000. Please contact Brivo Technical Support should you have any questions. 5
HID 5355 ProxPro The HID ProxPro readers are connected at a terminal strip inside the reader housing. The wiring diagram shows the expected wire colors for the connection between the ProxPro and the ACS5000. Please note any changes in the wiring schema to make sure that the correct terminals are interconnected. 22/6 500 Recommended Wire Installer Reader Wire Reader Location Function Panel Location Green DATA 0 Data 0 / Wiegand data0 White DATA 1 Data 1 / Wiegand data1 Black GROUND Reader Ground gnd Yellow BEEPER Buzzer / Optional buzz Red DC+ +12VDC 12vdc Orange GRN LED Green LED Control grn led Brown RED LED Red LED Control red led Blue N/A Not Used ***** N/A Violet N/A Not Used ***** N/A 6 Please refer to the HID Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the HID reader.
HID 6005 Proxpoint, 5395 ThinlineII, 5365 Mini-Prox The pigtail shown below is standard for most of the HID 6005, 5395 and 5365 model readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Wire Gauge Distance Reader Wire Function Panel Location Green Data 0 / Wiegand data0 White Data 1 / Wiegand data1 Black Reader Ground gnd Yellow Buzzer / Optional buzz Red +12VDC 12vdc Brown LED Control grn led Orange NOT USED ***** N/A Blue NOT USED ***** N/A Violet NOT USED ***** N/A Please refer to the HID Installation Manual associated with the reader to be installed for additional information. 7
Proximity Readers Farpointe Pyramid Readers The pigtail shown below is standard for most of the Farpointe Data Pyramid and Delta series readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. 22/8 or 18/8 may be required if the buzzer is required in conjunction with the Dual Line LED control option. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Reader Wire Function Panel Location Green Data 0 / Wiegand data0 White Data 1 / Wiegand data1 Black Reader Ground gnd Blue Buzzer / Optional buzz Red +12VDC 12vdc Orange Green LED Control grn led Brown(2) Red LED Control red led Yellow NOT USED ***** N/A Single Line Control: The Brown Wire connects to the Green LED Control and the Orange Wire is not connected. Dual Line Control: The Brown Wire connects to the Red LED Control and the Orange Wire connects to the Green LED control. Please refer to the Farpointe Data Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the Farpointe Data reader. 8
HID R10, R15, R30, R40, RK40 iclass Readers with 18 Pigtail The pigtail shown below is standard for most of the HID iclass and multiclass series readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Reader Wire Function Panel Location Green Data 0 / Wiegand data0 White Data 1 / Wiegand data1 Black Reader Ground gnd Yellow Buzzer / Optional buzz Red +12VDC 12vdc Orange Green LED Control grn led Brown Red LED Control red led Blue NOT USED ***** N/A Violet NOT USED ***** N/A Be sure to cover the unused wires. Grounding the Hold Wire can cause unreliable operation. LED Operation The LED will follow the configuration upon a card being read. During Valid Access or Rex, the ACS5000 will control the Green LED. During an Unlock Schedule, the LED will alternate Red/Green. During Credential Validation Check, The panel LED will alternate Red/Amber if available on the reader. Please refer to the HID Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the HID reader. 9
HID R10, R15, R30, R40, RK40 iclass Readers with Terminal The terminal shown below is standard for most of the HID iclass and multiclass series readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Recommended Wire Installer Reader Wire Reader Location Function Panel Location Green P2-3 Data 0 / Wiegand data0 White P2-4 Data 1 / Wiegand data1 Black P1-3 Reader Ground gnd Yellow P1-1 Buzzer / Optional buzz Red P1-4 +12VDC 12vdc Orange P1-2 Green LED Control grn led Brown P1-6 Red LED Control red led Blue N/A Not Used ***** N/A Violet N/A Not Used ***** N/A 10 Please refer to the HID Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the HID reader.
Proximity Readers Farpointe Delta Readers The pigtail shown below is standard for most of the Farpointe Data Pyramid and Delta series readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. 22/8 or 18/8 may be required if the Buzzer is required in conjunction with the Dual Line LED control option. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Reader Wire Function Panel Location Green Data 0 / Wiegand data0 White Data 1 / Wiegand data1 Black Reader Ground gnd Blue Buzzer / Optional buzz Red +12VDC 12vdc Orange Green LED Control grn led Brown(2) Red LED Control red led Yellow NOT USED ***** N/A Single Line Control: The Brown wire connects to the Green LED control and the Orange wire is not connected. Dual Line Control: The Brown wire connects to the Red LED control and the Orange wire connects to the Green LED control. Please refer to the Farpointe Data Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the Farpointe Data reader. 11
HID RP15, RP40, RPK40 iclass Readers with 18 Pigtail The pigtail shown below is standard for most of the HID iclass and multiclass series readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Reader Wire Function Panel Location Green Data 0 / Wiegand data0 White Data 1 / Wiegand data1 Black Reader Ground gnd Yellow Buzzer / Optional buzz Red +12VDC 12vdc Orange Green LED Control grn led Brown Red LED Control red led Blue NOT USED ***** N/A Violet NOT USED ***** N/A Be sure to cover the unused wires. Grounding the hold wire can cause unreliable operation. LED Operation The LED will follow the configuration upon a card being read. During Valid Access or Rex, the ACS5000 will control the Green LED. During an Unlock Schedule, the LED will alternate Red/Green. During Credential Validation Check, The panel LED will alternate Red/Amber if available on the reader. Please refer to the HID Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the HID reader. 12
HID RP15, RP40, RPK40 iclass Readers with Terminal The terminal shown below is standard for most of the HID iclass and multiclass series readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Recommended Wire Installer Reader Wire Reader Location Function Panel Location Green P2-3 Data 0 / Wiegand data0 White P2-4 Data 1 / Wiegand data1 Black P1-3 Reader Ground gnd Yellow P1-1 Buzzer / Optional buzz Red P1-4 +12VDC 12vdc Orange P1-2 Green LED Control grn led Brown P1-6 Red LED Control red led Blue N/A Not Used ***** N/A Violet N/A Not Used ***** N/A 13 Please refer to the HID Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the HID reader.
Wireless Receivers Chamberlain Liftmaster Wireless Receiver The configuration shown below is designed to connect one output on the Chamberlain Centex Wireless Receiver to the ACS5000. Most Centex transmitters have the ability to transmit a 26-bit credential to the receiver as well as to be used as a proximity FOB for traditional proximity readers. Please refer to the Chamberlain datasheets and installation guides regarding the proper transmitter/receiver combination. Reader Wire Function Panel Location Green Data 0 / Wiegand data0 White Data 1 / Wiegand data1 Black Reader Ground gnd Red +12VDC 12vdc Please refer to the Chamberlain Liftmaster Centex Receiver Installation Manual for instructions on proper installation. 14
Wireless Receivers Farpointe Ranger Wireless Receiver The configuration shown below is designed to connect one output on the Chamberlain Centex Wireless Receiver to the ACS5000. Most Centex transmitters have the ability to transmit a 26-bit credential to the receiver as well as to be used as a proximity FOB for traditional Proximity readers. Please refer to the Chamberlain datasheets and installation guides regarding the proper transmitter/receiver combination. Farpointe Ranger Term. Function Panel Location Green Wir ADO/BDO Data 0 / Wiegand data0 White AD1/BD1 Data 1 / Wiegand data1 Black GND Reader Ground gnd Red +12V +12VDC 12vdc Orange BDO/ADO Green LED Control grn led Brown BD1/AD1 Red LED Control red led Please refer to the Installation manual associated with the Farpointe Data Ranger Wireless Receiver for proper installation and configuration. 15
Reader Evaluation Request Form Brivo Systems will evaluate and qualify a reader for installation with the Brivo ACS5000 Panel. All we ask is that you provide us with a reader and the credentials required for operation. Evaluation of a reader may take up to two weeks to complete. Any reader that is sent to Brivo must be in like new condition and free of any defects. This service is open to all Brivo Authorized Dealers. Reader manufacturers are requested to contact Brivo s Product Management Team for evaluation. Company Name: Name: Address: City: State / Province: Zip / Postal Code: Phone Number: Email Address: Signature: Requirements: Reader must operate at 500 ft. Reader will be used in an elevator Reader requires power Reader must operate with specific credentials (include credentials with reader) Type of Reader: Prox 125Khz SC 13.56Mhz RF Multi-Tech Barcode / Magstripe Comments: This form may be emailed to customercare@brivo.com. A Technical Support Representative will follow up with a case number. When the reader is to be shipped to Brivo for evaluation, please be sure to include the case number and a copy of this form with the reader. If cards are to be tested with use on the reader, please send approximately 10 cards in non-sequential order. 16