PRO Series. Card Readers, Cards and Tags

Transcription

1 PRO Series Card Readers, Cards and Tags

2 All Proximity Card Readers: Offer high reliability, consistent read range characteristics, and low power consumption in a single, easy-to-install package. Are sealed in a rugged, weatherised polycarbonate enclosure designed to withstand harsh environments as well as provide a high degree of vandal resistance. This allows reliable performance anywhere. Recognise over 137 billion unique codes. Are warranted against defects in materials and workmanship for life from date of shipment. 2

3 ProxPoint Proximity Card Reader The HID ProxPoint proximity reader is so small and inconspicuous, you hardly know it s there. In addition to its small, attractive design, all of the reader electronics are potted making it ideal for both indoor and outdoor applications. The ProxPoint reader is available with either Wiegand interface or Clock-and-data magnetic stripe interface. The 5-volt capacity allows existing swipe-type access control installations to be easily upgraded to proximity technology, simply by changing the existing reader heads and cards. The Clock-anddata magnetic stripe version reads all HID proximity cards and outputs data in a Track II format. No rewiring or pulling of new cable is necessary. ProxPoint readers are designed to be unobtrusive and to mount directly on metal. When a proximity card is presented to the reader, the red LED flashes green. On reader power-up, an internal self-test routine checks and verifies the set-up configuration and initialises the reader operation. An additional external loop-back test allows for the reader outputs and inputs to be verified without the use of additional test equipment. The ProxPoint reader interfaces with all existing Wiegand protocol access control systems. ProxPoint readers output data in Wiegand format, plus optional Clock-and-data magnetic stripe format. The Clock-and-data magnetic stripe output interfaces with systems that originally read Track II magnetic stripe data using TTL level outputs of data, clock, and card present. Typical maximum* read range : ProxCard II card up to 9.5 cm ISOProx II card up to 5.8 cm ProxKey II key tag up to 4.3 cm ProxCard Plus card up to 3 cm * Depending on local installation conditions. Power supply : 4.75 ~ 16VDC Linear power supplies are recommended. Maximum current requirements : current (DC): Average 35 ma; Peak 60 ma Operating temperature : 30ºC ~ 65ºC Operating humidity : 0 ~ 95% relative humidity non condensing Transmit frequency : 125 khz Cable distance : Wiegand interface: 150 m Clock-and-data interface: 15 m Recommended cable is ALPHA 1295 (22 AWG) 5 conductor stranded with overall shield or equivalent. Material : polycarbonate UL 94 Colour options : black, charcoal grey, beige or white Dimensions : 7.96 x 4.3 x 1.3 cm (H x W x D) Weight : 75 g 3

4 MiniProx Proximity Card Reader The MiniProx proximity card reader boasts a slim design to match any decor. The attractive design allows the MiniProx reader to be mounted indoors or out. A new standard feature on the MiniProx reader is potting of all reader electronics, making this reader weatherised. The MiniProx reader is available with either Wiegand interface or Clock-and-data magnetic stripe interface. The 5-volt capacity allows existing swipe-type access control installations to be easily upgraded to proximity technology, simply by changing the existing reader heads and cards. The Clock-and-data magnetic stripe version reads all HID proximity cards and outputs the data in a Track II format. No rewiring or pulling of new cable is necessary. MiniProx readers are designed to be unobtrusive and to mount directly on metal such as door mullions. When a proximity card is presented to the reader, the red LED flashes green and the beeper sounds. The multicolour LED and beeper can also be controlled individually by the host system. On reader power-up, an internal self-test routine checks and verifies the set-up configuration, determines the internal or external control of the LED and beeper, and initialises the reader operation. An additional external loop-back test allows for the reader outputs and inputs to be verified without the use of additional test equipment. The MiniProx reader interfaces with all existing Wiegand protocol access control systems. MiniProx readers output data in Wiegand format, plus optional Clock-and-data magnetic stripe format. The Clock-and-data magnetic stripe output interfaces with systems that originally read Track II magnetic stripe data using TTL level outputs of data, clock, and card present. Typical maximum* read range : ProxCard II card up to14 cm ISOProx II card up to 10 cm ProxKey II key tag up to 5 cm ProxCard Plus card up to 4 cm * Depending on local installation conditions. Power supply : 4.75 ~ 16 VDC Linear power supplies are recommended. Current requirements : 5 VDC/12 VDC: Average 40 ma/50 ma; Peak 60 ma/120 ma Operating temperature : -30 C ~ 65 C Operating humidity : 0 ~ 95% relative humidity non condensing Transmit frequency : 125 khz Cable distance Wiegand interface: 150 m Clock-and-data interface: 15 m Recommended cable is ALPHA 1295 (22 AWG) 5 conductor stranded with overall shield or equivalent. Additional conductors may be required for LED or beeper control. Material : polycarbonate UL 94 Dimensions : 15.2 x 4.3 x 2.54 cm (H x W x D) Options : colour: charcoal grey or beige connection: terminal strip or pigtail Weight : with terminal strip 99 g / with pigtail 108 g 4

5 ProxPro Proximity Card Reader The ProxPro proximity card reader combines all of the electronics usually found in two separate packages into a single, architecturally attractive enclosure that mounts to a standard single-gang electrical box (U.S.A. Version). With its inherently weatherproof design, the reader is easily mounted either indoors or out. The ProxPro reader offers Wiegand protocol interface compatibility with all standard access control systems, plus optional RS232 and RS422 serial interfaces. To provide an additional level of security, the ProxPro reader is the first to offer an optional, fully integrated personal identification number keypad, weatherised for outdoor applications. Mounting holes fit standard U.S.A. single-gang switch boxes (vertically mounted) to simplify installation. When mounted directly to metal, a selectable jumper setting provides for improved performance. When a proximity card is presented to the reader, the red LED flashes green and the beeper sounds. The multicolour LED and beeper can also be controlled individually by the host system. On reader power-up, an internal self-test routine checks and verifies the set-up configuration, determines the internal or external control of the LED and beeper, and initialises the reader operation. An additional external loop-back test allows for the reader outputs and inputs to be verified without the use of additional test equipment. The ProxPro reader interfaces with all existing Wiegand protocol access control systems. ProxPro readers output data in Wiegand format, plus optional RS232 and RS422 serial interfaces. The ProxPro reader includes a tamper switch to provide electronic notification of reader tampering. The ProxPro reader is the first proximity design available with an optional, integrated, weatherised keypad. The ProxPro reader keypad interfaces with the host system either by sending the keypad data over the data output lines or via a direct connection to the host keypad interface. This offers an additional level of security by allowing the use of a personal identification number (PIN). Typical maximum* read range : ProxCard II card up to 23 cm ISOProx II card up to 15 cm ProxKey II key tag up to 7.6 cm ProxCard Plus card up to 7.6 cm * Depending on local installation conditions. Power supply : 10 ~ 28.5 VDC Reverse voltage protection included. Linear power supplies are recommended. Current requirements : current (DC) all versions: Average 100 ma; Peak 160 ma Operating temperature : -30 C ~ 65 C Operating humidity : 0 ~ 95% relative humidity non condensing Transmit frequency 125 khz Cable distance: Wiegand interface: 150 m RS232 interface: 15 m Recommended cable is ALPHA 1295 (22 AWG) 5 conductor stranded with overall shield or equivalent. Additional conductors may be required for LED or beeper control. Material : polycarbonate UL 94 Dimensions : 12.7 x 12.7 x 2.54 cm (H x W x D) Options : colour: charcoal grey or beige Wiegand Interface or Serial Interface Standard or Keypad Version Weight : 336 g 5

6 ThinLine II Proximity Card Reader The ThinLine II proximity card reader provides performance and reliability with a low-profile appearance. Housed in a newly designed two-piece enclosure, the ThinLine II reader is potted for weather and hazard proofing. This industry-standard sized USA switch plate enclosure eases installation and maintenance with the use of replaceable covers. The ThinLine II reader is available with either a Wiegand interface or a Clock-and-data magnetic stripe interface. The Clock-and-data interface version reads HID proximity cards programmed with magnetic stripe Track II data as well as standard Wiegand data. ThinLine II readers are designed to mount on a single-gang electrical box for easy installation. The readers can be mounted directly on metal with minimal impact on the read range performance. When a proximity card is presented to the reader, the red LED flashes green and the beeper sounds. The multicolour LED and beeper can also be controlled individually by the host system. On reader power-up, an internal self-test routine checks and verifies the set-up configuration, determines the internal or external control of the LED and beeper, and initialises the reader operation. An additional external loop-back test allows for the reader outputs and inputs to be verified without the use of additional test equipment. The ThinLine II reader interfaces with all existing Wiegand protocol access control systems. ThinLine II readers output data in Wiegand format, plus optional Clock-and-data magnetic stripe format. The Clock-and-data magnetic stripe output interfaces with systems that originally read Track II magnetic stripe data using TTL level outputs of data, clock, and card present. Typical maximum* read range : ProxCard II card up to 14 cm ISOProx II card up to 10 cm ProxKey II key tag up to 5 cm ProxCard Plus card up to 4 cm * Depending on local installation conditions. Power supply : 4.75 ~ 16 VDC Linear power supplies are recommended. Current requirements : 5 VDC/12 VDC: Average 40 ma/50 ma; Peak 60 ma/120 ma Operating temperature : -30 C ~ 65 C Operating humidity : 0 ~ 95% relative humidity non condensing Transmit frequency : 125 khz Cable distance : Wiegand interface: 150 m Clock-and-data interface: 15 m Recommended cable is ALPHA 1295 (22 AWG) 5 conductor stranded with overall shield or equivalent. Additional conductors may be required for LED or beeper control. Material : polycarbonate UL 94 Dimensions : 11.9 x 7.6 x 1.7 cm (H x W x D) Colour options : black, white, beige or charcoal grey Weight: : 94 g 6

7 The Noise Tolerant MaxiProx Proximity Card Reader The Noise Tolerant (NT) MaxiProx Reader provides a significant improvement in long range reading consistency. New signal processing techniques incorporated in this reader provide a high tolerance to burst and other transient types of ambient RF interference. This makes the NT MaxiProx reader ideal for installations incorporating parking control, or where special consideration is needed to facilitate access for the physically challenged. The NT MaxiProx reader provides up to 76 cm of consistent read range. Mount reader on non-metallic surfaces for optimal read range performance. Audio-visual indication: when a proximity card is presented to the reader, the red LED flashes green and the beeper sounds. The multicolour LED and beeper can also be controlled individually by the host system. On reader power-up, an internal self-test routine checks and verifies the set-up configuration, determines the internal or external control of the LED and beeper, and initialises the reader operation. The NT MaxiProx reader interfaces with all existing Wiegand protocol access control systems. The NT MaxiProx reader includes a tamper switch to provide electronic notification of reader tampering. Typical maximum* read range : Vehicle ID Tag up to 76 cm ProxCard II card up to 61 cm ISOProx II card up to 40.5 cm ProxKey II key tag up to 30.5 cm ProxCard Plus card up to 23 cm * Depending on local installation conditions. Power supply : 24 VDC Linear power supplies are recommended. Current requirements : current (DC); Average 1 A; Peak 1.7 A Operating temperature : -30 ~ 65 C Operating humidity : 0 ~ 95% relative humidity non-condensing Cable distance : Wiegand interface: 22 AWG m Recommended cable is ALPHA 1295 (22 AWG) 5 conductor stranded with overall shield or equivalent. Additional conductors may be required for LED or beeper control. Transmit frequency : 125 khz Material polycarbonate UL 94 Dimensions : 30 x 30 x 2.54 cm (H x W x D) Colour : charcoal grey Weight : 1.4 kg 7

8 Proximity Cards PX-4-H, PVC-H-4 and PVC-H-5 These proximity cards provide reliable and convenient access. Proximity technology allows fast, accurate reading while offering card read ranges from 10 cm to cm, dependant on the type of proximity reader being used. Since these cards do not require physical contact with the reader, they are virtually maintenance and wear-free. The PX-4-H, PVC-H-4 and PVC-H-5 are long lasting, flexible, credit card size proximity cards. Both the PVC-H-4 and PVC-H-5 allow for direct PVC printing of text, graphics and photos on the card s surface. The PVC-H-5 also offers the user both proximity and magnetic stripe technology for a wider range of access Credit card size for easy handling and storage. No batteries are required for operation. The cards are constructed of strong and flexible PVC to resist cracking and breaking. PVC-H-4, PVC-H-5 are designed to accept direct PVC printing of text, photos and graphics. The PVC-H-5 is a proximity/magnetic stripe card that allows use with both types of technology. All of these proximity devices come with a pre-programmed code number printed on each card. PX-4-H PX-4-H-PW PVC-H-4 PVC-H-4-26 PVC-H-5 PVC-H-5-26 Proximity card (34 Bit) with hole punch for badge clips; Northern Computers artwork Dimensions: 5.40 x 8.57 x 0.17 cm Proximity card (34 Bit) with hole punch for badge clips; plain white Dimensions: 5.40 x 8.57 x 0.17 cm Printable PVC proximity card (34 Bit); thin credit card style; suitable for badge printing; plain white Dimensions: 5.40 x 8.57 x cm Printable PVC proximity card (26 Bit); thin credit card style; suitable for badge printing; plain white Dimensions: 5.40 x 8.57 x cm Printable proximity card (34 Bit) with magnetic stripe (not encoded); thin credit card style; suitable for badge printing; plain white Dimensions: 5.40 x 8.57 x cm Printable proximity card (26 Bit) with magnetic stripe (not encoded); thin credit card style; suitable for badge printing; plain white Dimensions: 5.40 x 8.57 x cm Read range all devices 10 cm ~ cm Operating temperature -45 C ~ 70 C Power requirements none 8

9 ISOProx II The RF-programmable ISOProx II (26 Bit) access card offers proximity technology and photo identification on a single access control card. Accepts both horizontal and vertical slot punching, eliminating the need for badge holders. Meets ISO standards for thickness, for use with all direct image dye sublimation printers. The read range is extremely consistent and is unaffected by body shielding or variable environmental conditions, even when close to keys and coins. Can be carried with credit cards in a wallet or purse. Can be directly printed with video image printers and vertically or horizontally slot punched for easy use. A cross-reference list correlating the external card number and the programmed ID number is provided for easy system administration. Offers over 137 billion unique codes. Passive, no-battery design allows an infinite number of reads. Strong, flexible and resistant to cracking and breaking. Custom multicolour graphics are available. Typical maximum read range : MiniProx reader-up to 10 cm ThinLine II reader-up to 10 cm ProxPro reader-up to 15 cm NT MaxiProx reader-up to 40.5 cm Dimensions : 5.40 x 8.57 x cm Card construction : thin, flexible polyvinyl chloride (PVC) laminate. Operating temperature : -45 C ~ 70 C Weight : 6.8 g Description : 125 khz, RF programmable, customer-specified ID numbers, locations marked for slot punch Options : external card numbering slot punch (horizontal or vertical) custom graphics DuoProx II The DuoProx II card (26 Bit) provides a solution for companies desiring to use one card incorporating proximity, magnetic stripe and photo identification technologies for multiple applications. The DuoProx II card accepts both horizontal and vertical slot punching, eliminating the need for badge holders. The DuoProx II card meets ISO standards for thickness, for use with all direct image printers and magnetic stripe readers. Proven, reliable technology: the read range of the DuoProx II proximity card is extremely consistent. It is not affected by body shielding or variable environmental conditions, even when close to keys and coins. Can be carried with credit cards in a wallet or purse. The DuoProx II card can be directly printed with video image printers and vertically or horizontally slot punched for easy use. A cross-reference list correlating the external card number and the programmed ID number is provided for easy system administration. External numbering matching the encoded numbers is available. The DuoProx II proximity card offers over 137 billion unique codes. DuoProx II proximity cards offer a passive, no-battery design, allowing for an infinite number of reads. DuoProx II proximity cards are strong and flexible for resistance to cracking and breaking. Custom multicolour graphics are available. 9

10 Typical maximum read range : MiniProx reader up to 10 cm ThinLine II reader up to 10 cm ProxPro reader up to 15 cm NT MaxiProx reader up to 40 cm Dimensions : 5.40 x 8.57 x cm Card construction : thin, flexible polyvinyl chloride (PVC) laminate with an ABA standard, high coercivity magnetic stripe rated 4000 Oerstad. Operating temperature : -45 C ~ 70 C Weight : 6.8 g Description : 125 khz, RF programmable, customer-specified ID numbers, locations marked for slot punch Options : Card Finish for Direct Printing External Card Numbering Slot Punch (Horizontal or Vertical) Custom Graphics SmartProx HID s SmartProx proximity card offers the thin card features of the ISOProx II and DuoProx II proximity cards in a package designed for implantation of contact smart card technology. The SmartProx card meets customer requirements for network access, data security, debit transactions, parking, benefit information storage, photo ID and proximity access control with a single card. It provides physical access to data processing areas, as well as logical access to corporate databases. The SmartProx card is able to carry a complete biometric identifier for critical perimeter access control while providing the ease of use of proximity elsewhere. Note: Applications of smart chip depend on size of chip memory and software. HID does not manufacture smart chip modules. The read range is consistent and is unaffected by body shielding or variable environment conditions, even when close to keys and coins. Easily carried with credit cards in a wallet or purse. A cross-reference list correlating the external card number and the programmed ID number is standard for easy system administration. External numbering matching the encoded numbers is available. Can be directly printed with dye-sublimation video image printers. Passive, no-battery design allows an infinite number of reads. Strong, flexible and resistant to cracking and breaking. Custom multicolour graphics are available. Typical maximum read range : ProxPoint reader-up to 3.5 cm MiniProx reader-up to 6.2 cm ThinLine II reader-up to 6.2 cm ProxPro reader-up to 12.5 cm ProxPro Plus reader-up to 14.0 cm MaxiProx reader-up to 35.5 cm Card Dimensions : 5.40 cm x 8.57 cm x cm Card Construction : thin, flexible polyvinyl chloride (PVC) laminate Operating Temperature : -45 C ~ 70 C Humidity : 5 ~ 95% relative humidity, non-condensing Weight : (without smart chip) 6.8 g Description : 125kHz, RF-programmable, customer-specified ID numbers, locations marked for slot punch Options : external card numbering slot punch (horizontal or vertical) custom graphics The SmartProx proximity card can be purchased: From your HID distributor, ready for smart chip implantation by the smart chip manufacturer of your choice. From an HID Value Added Reseller (VAR) with the smart chip already implanted. 10

11 Proximity Tags ProxKey II Proximity Key Tags The RF-programmable ProxKey II proximity key tag incorporates proximity technology into a convenient device approximately the size of an automotive key. This key tag offers universal compatibility with all HID proximity readers and provides an external number for easy identification and control. The key tag can be placed on a key ring for convenient entry. The read range is extremely consistent and is unaffected by body shielding or variable environmental conditions, even when close to keys and coins. Can be carried with keys in pocket or handbag. A cross-reference list correlating the external card number and the programmed ID number is provided for easy system administration. External numbering matching the encoded numbers is available. Offers over 137 billion unique codes. Passive, no-battery design allows an infinite number of reads. Polycarbonate package is resistant to cracking and breaking. Typical maximum read range : MiniProx reader-up to 5 cm ThinLine II reader-up to 5 cm ProxPro reader-up to 7.6 cm NT MaxiProx reader-up to 30.5 cm Dimensions : 4.83 x 2.29 x 0.88 cm Key tag construction : Ultrasonically welded, polycarbonate shell Operating temperature : -45 C ~ 70 C Weight : 7.4 g Description : 125 khz, RF-programmable, charcoal grey, customer-specified ID Numbers, key ring included. Options : external card numbering custom graphics/logo proximity key tag 34 Bit or 26 Bit version The ProxPass The ProxPass is an active tag specially designed for vehicle access control. Providing convenient access control for parking and fleet management applications, ProxPass is an ideal augmentation to an existing or new HID proximity installation. It can be encoded with any HID format and numbering system used by HID proximity cards, including the Corporate 1000 format. RF-programmable, customer specified ID numbers. Options: external card numbering. A cross-reference list correlating the external card number and the programmed ID number provides easy system administration. Over 137 billion unique codes available. Compatible with MaxiProx reader and all HID card formats Dual battery design and low current draw allows two to five years with typical usage. Rugged, UV-resistant, sonic-welded polycarbonate case is also weather resistant. Typical maximum* read range : 1.9 m (using MaxiProx reader) * Depending on local installation conditions. Mounting location : interior windshield, driver s side, upper or lower corner Dimensions 91.6 x 67.5 x 7.6 mm Operating temperature -30 C ~ 85 C Environmental 5 ~ 95% RH, non-condensing (not for marine usage) 11

12 For further information, please contact: SH Printed in NL 2001 All Rights Reserved subject to change without prior notice Proximity (E) / V.01